Beruflich Dokumente
Kultur Dokumente
http://www.brest-wireless.net/wiki/materiel:amos
http://pe2er.nl/omniusb/index.htm
http://pe2er.nl/wifisector/index.htm
Antenne Amos
Plus connue sous le nom d’antenne Serbe (ou Russe) :) Il n’y a pas de
plan de cette antenne en anglais ou français. Elle est quasiment
inconnue, j’ai donc déchiffré ce dialecte pour vous. L’adresse originale
est:
http://yu1aw.ba-karlsruhe.de/Amos.pdf
http://www.qsl.net/yu1aw/vhf_ant.htm
http://home.wanadoo.nl/erwin.gijzen/wifisector/
http://www.amateur.dzand.nl/amos/
http://pe2er.nl/wifisector/index.htm
Construction
Matériel nécessaire:
Le reflecteur
Dans un premier temps, j’ai réalisé le reflecteur. En effet, comme je
n’avais pas de PCB si long que cela sous la main, j’ai utilisé 2 morceaux
que j’ai soudé entre eux à l’aide d’une petite plaque de cuivre.
Positionnement
Placer les deux feeds sur le PCB, percez 4 trous afin de faire tenir les
feeds sur le PCB. Ensuite couper 4 morceaux de bic de 10mn de long,
et coller les dans les trous.
Le balun
Pour avoir deux courants opposés en phase nécessaire à l’attaque des
feeds, on utilise une ligne de lambda / 2 sur l’un des brins. La demi-
onde déphase le courant du coaxial, qui est alors partagé en deux
parties. Le fait de diviser le courant par deux revient à avoir une
Les feeds impédance multipliée par 4.
Une bonne partie de pliage de fil de cuivre 2mn carré vous attend. Il
faut respecter les dimensions au pied de la lettre. Un bon étau est
indispensable pour le pliage..
Voici le résultat:
Le balun est certainement l’élément le plus difficile à réaliser. J’ai utilisé
du cable RG58, en fait le RF195 est beaucoup trop fragile pour ce genre
de chose, il fond à l’approche du fer à souder.
C'est fini ?
Il ne reste plus qu’à souder les feeds, et coller le tout avec précaution.
Quelques points de colle permettent de rigidifier la structure.
Tests et conclusion
Tout d’abord:
Cette antenne est très fragile.. j’ai cassé un balun lors des premiers
tests
La bonne réalisation du balun est vraiment délicate.
Polarisatie Verticaal
Vertical beamwidth (-
3dB) 15º
Homebrew Sector Antenna for Wifi ISM band (2,4GHz)
Horizontal
beamwidth (-3dB)
125º
On this page you will find information on how I build a sector antenna for de
Wifi 2,4GHz ISM band. Connector: Female-N
type (50 Ohm)
The design was published by Dragoslav Dobričić, YU1AW.
This is my version of his design. Overall, the dimensions are a little shorter:
Make a hardcopy of the Autocad drawing (the antenna is drawn to scale 1:1).
Drill a hole in the centre to accept your N-Type connector. I Use one that
comes with rigid coax attached. The shield of the coax should extend to
28mm above the surface of the PCB. The centre conductor must extend 5mm
more. Drill 4 holes to attach the studs to the reflector.
Bend the two radiators. Do not forget to slide on the PE studs before
bending. Remember: It is the amount of wire you use that is important, not
the final dimensions after bending!
Screw or rivet the PE studs to the radiator.
I Use S-Lon 65mm mini PVC rain gutter to house the sector antenna. I am
sure that this is not available all over the world, so you need to find
“Verbindingen KORT houden” means “keep connections SHORT as possible”.
something similar.
Solder the radiator to the coax feed/ BALUN.
I have also used this antenna without a radome. It is however very
susceptible to mechanical damage.
Links Een WLAN Omni USB Adapter IEEE802.11b/g by
PE2ER
http://www.qsl.net/yu1aw/ VHF/ UHF Antennae by Dragoslav Dobričić,
YU1AW
Een variatie op de 8dBi hotspot omni
http://www.brest-wireless.net/wiki/materiel:amos Brest Wireless AMOS
Antenne pagina (French) Introductie
http://www.wirelessnederland.nl Wireless Nederland – Infinite well of Bij wijze van experiment heb ik een IEEE802.11b/g Wifi
knowledge on the subject of Wifi (Dutch) USB Adapter gemonteerd in een 8dBi omnidirectional
antenne. De omni is via een stukje dun teflon coax op de
http://forum.wirelessnederland.nl/viewtopic.php?t=8128&highlight= WLNL:
USB stick aangesloten. De adapter is een Canyon-tec
Drie AMOS Sector antennes voor Wireless Pinkster Kamp 2006 (Dutch)
CN-WF518.
http://forum.wirelessnederland.nl/viewtopic.php?t=7428 WLNL: Zelfbouw
125° 12dBi Sector antenne uit Servië (YU1AW) (Dutch) De (enige) diëlectrische antenne op de print van de USB
adapter is hiervoor verwijderd. De externe antenne is hier
Disclaimer simpelweg voor in de plaats gesoldeerd.
I will not be responsible for damage to equipment, your ego, personal injury or worse
Dethat may result zijn verbluffend. AP´s die met de standaard
resultaten
from the use of this material and material found on any links on my pages. You are responsible
antennestoniet
makete vangen zijn, worden nu met 11Mbps
sure that your use any of my designs is legal in your country. geconnect.
PE2ER Homebrew projects page De USB wifi adapter en antenne straler zijn vervolgens
ingebouwd in een standaard 32mm PVC pijp. Een 4,5
Copyright: Erwin Gijzen meter lange USB kabel verzorgt de verbinding met de
PC.
Version: Nov-2007
Het witte blokje vooraan is de antenne. Adapter uit zijn jasje.
Antenne eraf, coaxje voor de omni ervoor in de plaats. De mantel van de coax is aan de onderzijde op 2
plaatsen met de massa verbonden.
Gat in jasje gemaakt voor de mini coax (het is een stukje
RG-316) en het jasje weer dichtgeritst.
http://www.canyon-
tech.com/products/show.cfm/Net/Wireless_Products_IEE
E_802.11g/CN-WF518
Uitgebreide instellingen voor de Access Point modus.
Links
http://home.deds.nl/~pe2er/antennetesten/antennameasurement.htm Testen
van (zelfbouw) Wifi antennes met eenvoudige zelfbouw meetinstrumenten
http://www.qsl.net/pa0hoo/helix_wifi/linkbudgetcalc/wlan_budgetcalcnl.html W
LAN Link planner