Beruflich Dokumente
Kultur Dokumente
,LTD
PRODUCT SPECIFICATION
【 ◆ 】 Preliminary Specification
【 】 Finally Specification
CUSTOMER’S APPROVAL
SIGNATURE: DATA:
DENG
Prepared By :
Revision record
Table Of Contents
0 Cover 1
0 Revision Record 2
0 Table Of Contents 3
1 General Description 4
2 External Dimensions 5
3 Interface Description 6
5 Electrical Characteristics 8
6 Timing Characteristics 9
7 Backlight Characteristics 13
8 Optical Characteristics 14
10 Inspection Standard 17
11 Handling Precautions 18
1. General Description
1.1 Description
KWH040ST01-F01-B is a Transmissive type color active matrix liquid crystal display (LCD),
which uses amorphous thin film transistor (TFT) as switching devices. This product is
composed of a TFT LCD panel, driver IC, FPC and backlight unit . The following table
described the features of FORMIKE KWH040ST01-F01-B.
1.2 Application
Mobile phone, Multimedia products
and other electronic Products
Etc.
1.3 Features:
Features Description UNITS
LCD type 3.97’’TFT --
Dot arrangement 480(RGB)×800 dots
Driver IC NT35510 --
Color Depth 16.7M
Interface RGB ,MCU Interface --
View Direction ALL View(IPS) --
Module size 57.06(W) ×98.10 (H)×2.10(T) mm
Active area 51.84(W) ×86.4(H) mm
Dot pitch 0.108 (W) ×0.108 (H) mm
Back Light 8 White LED In serial --
With/Without TSP Without TSP
Weight(g) TBD
www.wandisplay.com
1 GND 27 DB14
2 YU 28 DB15
57.06±0.2 2.10±0.1
3 XL 29 DB16 52.06±0.1 2.50
51.84(LCD)(A.A) 2.61 4-1.00 压痕线 压痕线
2.00
4 YD 30 DB17
3.20
不包含导电布厚度
5 XR 31 DB18
6 VCC 32 DB19
喷码:KWH040ST01 CR+日期 喷码:KWH040ST01 CR+日期
PULL TAPE
7 VCC 33 DB20 17*8
8 GND 34 DB21
9 VS 35 DB22
单面带胶导电布T =0.10mm 单面带胶导电布T =0.10mm
10 HS 36 DB23
11 PCLK 37 IOVCC
FORMIKE
2. External Dimensions
56.00
12 DE 38 GND
13 DB0 39 RESET
3.97"TFT
86.40(LCD)(A.A)
14 DB1 40 CS
98.10±0.2
480RGB*800
15 DB2 41 RD
IPS
16 DB3 42 WR/SCL
17 DB4 43 RS
DB5 2.00 3.00 10.96±0.3
18 44 SDI
5/19
19 DB6 45 SDO
1
20 DB7 46 FMARK
21 DB8 47 IM0
22 DB9 48 IM1
57.06
51
23 DB10 49 A
30.80±0.3
XR YD XL YU
24 DB11 50 K
4*0.80
K A
213 1
26 DB13
4*2.50
COMPONENT AREA COMPONENT AREA
0.75
A K
单层区域 单层区域 单层区域
YU XL YD XR XR YD XL YU
KA
对位线(总厚T=0.2MM)
51 51
33.31±0.3
A Stiffener
PI 补强
1 1
对应连接器:HRS:FH26-51S-03SHW
2.50 <0.2>±0.03 3.50
51
NOTES:
Ver.1.0
1. DISPLAY TYPE: TFT
A1 K1
CUSTOMER APPROVE FORMIKE ELECTRONIC CO.,LTD.
0.3±0.03
W=0.3±0.03
14.4±0.03
15.6±0.07
3. Interface Description
PIN NO. PIN NAME DESCRIPTION
1 GND Ground.
2 YU Touch Panel Up Side Wire.
3 XL Touch Panel Left Side Wire.
4 YD Touch Panel Down Side Wire.
5 XR Touch Panel Right Side Wire.
6-7 VCC Power supply (+2.3V~+4.8V).
8 GND Ground.
VS Frame synchronizing signal for RGB interface operation.
9
Fix to GND level when not in use.
HS Line synchronizing signal for RGB interface operation.
10
Fix to GND level when not in use.
PCLK Dot clock signal for RGB interface operation.
11
Fix to GND level when not in use.
DE Data enable signal for RGB interface operation.
12
Fix to GND level when not in use.
DB0-DB23 24-Bit parallel data bus for 8080 system and RGB interface mode.
13-36
Fix to GND level when not in use.
37 IOVCC Power supply Voltage for I/O Interface (+1.65V~+3.3V).
38 GND Ground.
RESET This signal will reset the device and must be applied to properly initialize
39
the chip. Signal is active low.
40 CS Chip select input pin(“ low” enable).
RD 8080 system(RD):Serves as a read signal and MCU read data at the rising
41 edge.
Fix to GND when not in use.
WR/SCL 8080 system(WR):Serves as a write signal and writes data at the rising
edge.
42
SCL: a synchronous clock in SPI Interface.
Fix to GND level when not in use.
RS This pin is used to select ”data or command” in the 8080 system interface
When RS=’’1’’, data is selected.
43
When RS=’’0’’, command is selected.
Fix to GND when not in use.
SDI Serial input signal in SPI interface. The data is input on the rising edge of
44 the SCL signal.
Fix to GND when not in use.
SDO Serial output signal in SPI interface. The data is output on the rising edge of
45 the SCL signal.
Fix to open when not in use.
FMARK Tearing effect output pin to Synchronous MCU to frame writing.
46
activated by S/W command. If not used, please open this pin.
47 IM0 Interface type selection:
IM1 IM1 IM0 SRAM Register
48 0 0 80-8bit MPU I/F80-8bit MPU I/F DB[7:0]
5. Electrical Characteristics
6.Timing Characteristics.
7. Backlight Characteristics.
Test
Item Symbol MIN TYP MAX UNIT Note
Condition
Supply Voltage Vf 23.2 26.4 30.4 V If=60 mA -
Supply Current If - 20 - mA - -
Reverse Voltage Vr - - 5 V 10uA
Power dissipation Pd - 528 - mW -
Luminous Intensity for L 400
CM
- -
Cd/m2 If=60 mA
Uniformity for LCM - 80 - - % If=60 mA
Life Time - 50000 - - Hr If=60 mA -
Backlight Color White
8.Optical Characteristics
10.Inspection Standard
11.4 packing
z Module employ LCD elements and must be treated as such.
z Avoid intense shock and falls from a height.
z To prevent modules from degradation, do not operate or store them exposed direct to sunshine or high
temperature/humidity
11.6 storage
In the case of storing for a long period of time for instance, for years for the purpose or replacement use, the
following ways are recommended.
z Storage in a polyethylene bag with the opening sealed so as not to enter fresh air outside in it . And with no
desiccant.
z Placing in a dark place where neither exposure to direct sunlight nor light’s keeping the storage temperature
range.
z Storing with no touch on polarizer surface by the anything else.
It is recommended to store them as they have been contained in the inner container at the time of delivery from
us
11.7 Safety
z It is recommendable to crash damaged or unnecessary LCD’s into pieces and wash off liquid crystal by either
of solvents such as acetone and ethanol, which should be burned up later.
z When any liquid leaked out of a damaged glass cell comes in contact with your hands, please wash it off well
with soap and water
12.2
On the following occasions, the handing of problem should be decided through discussion and agreement
between responsible of the both parties.
z When a question is arisen in this specification
z When a new problem is arisen which is not specified in this specifications
z When an inspection specifications change or operating condition change in customer is reported to FORMIKE
ELECTRONIC CO,.LTD,and some problem is arisen in this specification due to the change
z When a new problem is arisen at the customer’s operating set for sample evaluation in the customer site.