Beruflich Dokumente
Kultur Dokumente
SLIDE GUIDES
S W I V E L S L I D I N G G U I D E S H O E S
El
COST-EFFECTIVE.
LSCO’S SPRING-LOADED SWIVEL SLIDING G UIDE SHOES PROVIDE RIDE QUALITY IN A COST-
E
SA-15
EFFECTIVE PACKAGE IN THOSE APPLICATIONS THAT DO NOT ALLOW FOR THE INSTALLATION
OF ROLLER GUIDES. U NSURPASSED BUILD QUALITY AND DURABLE MATERIALS ENSURE A SA-8
LIFETIME OF RELIABLE PERFORMANCE, AND A COMPREHENSIVE ARRAY OF SIZES AND GIB LINER
OPTIONS ENSURE THAT ELSCO SWIVEL SLIDING G UIDE SHOES ARE SUITABLE ACROSS A WIDE RANGE
OF APPLICATIONS.
■■■■■■■■■■■■■■■■■■■■
■■■■■■■■■■■■■■■■■■■■
Optional molybdenum-disulfide-filled nylon rails.
gibs include a graphite-like solid lubricant •Rail gibs can be modified to
impregnated into the gib material and accommodate 18.5-lb. (T140-1B) rails.
provide added durability, particularly in
■■■■■■■■■■
■■■■■■■■■■
applications where rails are not lubricated.
Gibs are made to fit 5/8-in. (16mm) rail ELSCO roller guides and swivel sliding
blades, and can be modified to fit 3/4-in. guide shoes offer a cost-effective
■■■
■■■
(19mm) rails. approach for improving elevator ride
quality by reducing the need for expensive,
labor-oriented solutions and ongoing A typical installation:
maintenance. That’s why, to elevator Passenger Elevator Cabin guides
contractors around the world, the ELSCO for Low-Rise Hydraulic Elevator.
name is synonymous with quality and Speed: 100 fpm (0,5 m/s).
value. At ELSCO, We are ride quality. Capacity: 2,500 lbs. (1.100 kg).
See inside for mounting instructions. Many factors must be considered when
making a guide selection. Please call us to
SC-8
SL
discuss your specific application. SD-8
410.363.9020
info@elscoguides.com S W I V
ELSCO’s Swivel Sliding Guide Shoes are HUB AND GIB ASSEMBLY
designed with adjustment features that provide BRACKET
the best possible riding characteristics when HUB
Installation Instructions guide shoes are specified. The installer can
Swivel Slide Guide Shoes
HUB BRACKET
1/4"
GAP
3 4 5
Slide the hub and gib assembly into the bracket. Position swivel sliding guide shoe onto the With gib seated firmly against the rail face, set
rail while lowering mounting bracket over the 1/4" (6 mm) gap between the gib holder and
mounting hole or studs. Install mounting bracket.
hardware (not included).
HUB ADJUSTING
SCREW AND NUT
GREASE FITTING
6 7 8
Securely tighten mounting bolts and/or nuts. At this point, install the remaining guides on Insert hub adjusting screw and nut into bracket.
top of and/or beneath the elevator. Lubricate Adjustment of this screw regulates the pressure
the fitting on each guide with general purpose of the gib against the face of the rail.
grease until a small amount appears between
the hub and bracket. If guides are equipped with adjustable
stops, proceed with steps 9 and 10.
9 10 11
To limit postwise float, turn adjustment screw When the desired amount of postwise float is After all adjustments have been made, ride
clockwise until it makes contact with solid stop set, tighten the locknut securely while holding elevator in both the up and down direction at
washer (installed in step 2 “Note”). At this point, float adjustment screw in place. inspection speed to check hoistway clearances.
there will be zero postwise float. To increase Check to be sure that all mounting bolts and/or
float, turn adjustment screw counterclockwise. nuts, and adjustment locknuts are securely
Note: Each full turn equals 1/16" (2 mm). tightened. Make several more runs at operating
speed, then recheck float (if applicable) before
returning elevator to service.
2 3/8 in
(60mm)
1 3/16 in
Models Models
(30mm)
Mounting Templates
Swivel Slide Guide Shoes
SC-8 SA-15
SD-8 SA-8
1 1/16 in
(27mm)
11/16 in
(18mm)
7 7/16 in
1 1/16 in (189mm)
(27mm) FROM FACE OF RAIL
7 1/16 in (MODELS SA-15 & SA-8
(179mm) 8 1/4 in
FROM FACE OF RAIL (210mm)
MAXIMUM OVERALL
7 15/16 in
DEPTH
(202mm) 9 7/16 in
2 3/8 in (MODEL SA-8)
MAXIMUM OVERALL (240mm)
(60mm)
DEPTH MAXIMUM OVERALL
DEPTH
(MODEL SA-15)
1 1/2 in
(38mm)
4 in
(102mm)
MAXIMUM OVERALL
WIDTH
SHOWN ON 8# RAIL
SHOWN ON 8# RAIL MODEL SA-15 TO BE USD ON 15# RAIL ONLY
Models
SA-15
SA-8
11/16 in
(18mm)
1 1/16 in
(27mm)
5 1/2 in
(140mm)
2 3/4 in
(70mm)
7 7/16 in
(189mm)
FROM FACE OF RAIL 3 in
(MODELS SA-15 & SA-8 (76mm)
8 1/4 in
(210mm)
MAXIMUM OVERALL
DEPTH
9 7/16 in
(MODEL SA-8)
(240mm)
MAXIMUM OVERALL
DEPTH
(MODEL SA-15)
2 1/4 in
(57mm)
7 in
(178mm)
MAXIMUM OVERALL
WIDTH
SHOWN ON 8# RAIL
TEM PLATES S HOWN ACTUAL S IZ E MODEL SA-15 TO BE USD ON 15# RAIL ONLY
Swivel Sliding Guide Shoes
Specifications
Note: All metric dimensions are rounded off to the nearest millimeter
Rail Gib Style and Dimensions Available in Nylon or Molybdenum Disulfide-Filled Nylon
Dimension
Model Gib Style I J K L M
SA-15 15 lb HI-WALL GIB 2 3/8" 1 7/8" 5/8"* 1 11/16" 8 1/2"
(60mm) (48mm) (16mm) (43mm) (216mm)
SA-8/ 8 lb LO-WALL GIB 1 1/2" 1" 5/8"* 1 11/16" 8 1/2"
SC (38mm) (25mm) (16mm) (43mm) (216mm)
SD-8 8 lb LO-WALL GIB 1 3/8" 1" 5/8" 1 3/8" 5 1/2"
(35mm) (25mm) (16mm) (35mm) (140mm)
*3/4" (19mm) Available for Model SA-15 and SA-8 Swivel Guides
Note: All metric dimensions are rounded off to the nearest millimeter