Beruflich Dokumente
Kultur Dokumente
J0088K-00-APM303
33504494701NE_14
J88K
Engine ref. 4045TF220
Alternator ref. KH00973T
Performance class G3
GENERAL CHARACTERISTICS
Frequency (Hz) 50 Hz
Voltage (V) 400/230
Standard Control Panel APM303
Optional control panel TELYS
Optional Control Panel M80
Optional control panel NA
POWER
ESP PRP
Voltage Standby Amps
DESCRIPTIVE kWe kVA kWe kVA
Mechanic governor
415/240 70 88 64 80 122
Mechanically welded chassis with antivibration
suspension 400/230 70 88 64 80 127
Main line circuit breaker 380/220 69 86 62 78 131
Radiator for core temperature of 48/50°C max with 200/115 70 88 64 80 254
mechanical fan
240 TRI 70 88 64 80 212
Protective grille for fan and rotating parts (CE option)
9 dB(A) silencer supplied separately
230 TRI 70 88 64 80 221
Charger DC starting battery with electrolyte 220 TRI 70 88 64 80 231
12 V charge alternator and starter
Delivered with oil and coolant -30°C DIMENSIONS COMPACT VERSION
Manual for use and installation Length (mm) 1870
Width (mm) 994
POWER DEFINITION
Height (mm) 1360
PRP : Prime Power is available for an unlimited number of annual
operating hours in variable load applications, in accordance with ISO Dry weight (kg) 1088
8528-1. ESP : The standby power rating is applicable for supplying
emergency power in variable load applications in accordance with ISO Tank capacity (L) 180
8528-1. Overload is not allowed.
TERMS OF USE
According to the standard, the nominal power assigned by the genset is
DIMENSIONS SOUNDPROOFED VERSION
given for 25°C Air Intlet Temperature, of a barometric pressure of 100 Type soundproofing M128
kPA (100 m A.S.L), and 30 % relative humidity. For particular conditions
in your installation, refer to the derating table. Length (mm) 2300
ASSOCIATED UNCERTAINTY Width (mm) 1060
For the generating sets used indoor, where the acoustic pressure levels
depends on the installation conditions, it is not possible to specify the Height (mm) 1680
ambient noise level in the exploitation and maintenance instructions .
You will also find in our exploitation and maintenance instructions a Dry weight (kg) 1508
warning concerning the air noise dangers and the need to implement Tank capacity (L) 180
appropriated preventive measures.
Acoustic pressure level @1m in dB(A) 76
Sound power level guaranteed (Lwa) 94
Acoustic pressure level @7m in dB(A) 64
33515266401 3
19/05/2017
J88K
ENGINE CHARACTERISTICS
EMISSIONS
Emission PM (mg/Nm3) 5% O2 60
Emission CO (mg/Nm3) 5% O2 190
Emission HC+NOx (g/kWh) 0
Emission HC (mg/Nm3) 5% O2 34
33515266401 3
19/05/2017
J88K
ALTERNATOR CHARACTERISTICS
DIMENSIONS
Dimensions soundproofed version Dimensions DW compact version
Type soundproofing M128 Type soundproofing
Length (mm) 2300 Length (mm) 2344
Width (mm) 1060 Width (mm) 1060
Height (mm) 1680 Height (mm) 1579
Dry weight (kg) 1508 Dry weight (kg) 1362
Tank capacity (L) 180 Tank capacity (L) 390
Acoustic pressure level @1m in dB(A) 76 Acoustic pressure level @1m in dB(A)
Sound power level guaranteed (Lwa) 94 Sound power level guaranteed (Lwa)
Acoustic pressure level @7m in dB(A) 64 Acoustic pressure level @7m in dB(A)
Dimensions DW soundproofed version Dimensions DW 48h soundproofed version
Type soundproofing M128 DW Type soundproofing M128 DW48
Length (mm) 2344 Length (mm) 2344
Width (mm) 1060 Width (mm) 1060
Height (mm) 1900 Height (mm) 1989
Dry weight (kg) 1695 %PdnetE_5% 1725
Tank capacity (L) 390 Tank capacity (L) 700
Acoustic pressure level @1m in dB(A) 76 Acoustic pressure level @1m in dB(A) 76
Sound power level guaranteed (Lwa) 94 Sound power level guaranteed (Lwa) 94
33515266401 3
19/05/2017
Acoustic pressure level @7m in dB(A) 64 Acoustic pressure level @7m in dB(A) 64
33515266401 3
19/05/2017
J88K
CONTROL PANEL
33515266401 3
19/05/2017
M80, transfer of information Basic terminal block
The M80 is a dual-function control unit. It can be used as a The control unit can be used as a basic terminal block for
basic terminal block for connecting a control box and as an connecting a control box.
instrument panel with a direct read facility, with displays
giving a global view of your generating set's basic Offers the following functions:
parameters.
emergency stop button, customer connection terminal
Offers the following functions: block, CE.
33515266401 3
19/05/2017
General and safety manual
Generating set
IZIDOC-1311_EN
2017/07/17 33532000201_6_1
MGS_ 33532000201_6_1
CONTENTS
1 Preface........................................................................................................................................................................................ 4
1.1 Description of the documentation for generating sets ........................................................................................................ 4
1.2 General recommendations ................................................................................................................................................. 5
2 Safety instructions ....................................................................................................................................................................... 6
2.1 Meaning of the pictograms on the generating set............................................................................................................... 6
2.2 General guidelines ............................................................................................................................................................. 7
2.3 Risks relating to handling phases ....................................................................................................................................... 9
2.4 Risk of electrocution ........................................................................................................................................................... 9
2.4.1 Safety precautions in case of electrical shock................................................................................................................ 9
2.5 Risk of fire, burns and explosions..................................................................................................................................... 10
2.6 Risks relating to exhaust gases and Risks related ........................................................................................................... 11
2.7 Risks relating to noise ...................................................................................................................................................... 12
2.8 Guidelines for protecting the environment ........................................................................................................................ 12
3 General description of the equipment ....................................................................................................................................... 13
3.1 Identification plates........................................................................................................................................................... 13
3.1.1 Identifying sets ............................................................................................................................................................. 13
3.1.2 Location of plates on generating sets with and without an enclosure .......................................................................... 14
3.1.3 Location of plates on containerised generating sets .................................................................................................... 14
3.1.4 Identifying generating set components ........................................................................................................................ 15
3.2 Fixed generating set ......................................................................................................................................................... 16
3.2.1 Generating set without protective cover ....................................................................................................................... 16
3.2.2 Generating set with protective cover ............................................................................................................................ 17
3.3 Mobile generating set ....................................................................................................................................................... 18
3.3.1 Generating set without trailer ....................................................................................................................................... 18
3.3.2 Trailer-mounted generating set .................................................................................................................................... 19
3.3.3 Lighting column ............................................................................................................................................................ 19
3.4 Containerised generating set ........................................................................................................................................... 20
3.4.1 ISO 20 and ISO 40 containers ..................................................................................................................................... 21
3.4.2 CPU 20 and CPU 40 containers .................................................................................................................................. 22
3.4.3 CIR 20 containers ........................................................................................................................................................ 23
3.4.4 Trailer-mounted container ............................................................................................................................................ 23
3.5 Technical characteristics and operation of additional equipment (if so equipped) ............................................................ 24
3.5.1 Built-in fluid retention container (option) ....................................................................................................................... 24
3.5.2 REN-RAB automatic oil auxiliary adjuster .................................................................................................................... 25
3.5.2.1 Technical specifications ........................................................................................................................................... 25
3.5.2.2 Operation ................................................................................................................................................................. 25
3.5.3 JAPY manual pump ..................................................................................................................................................... 26
3.5.4 JAPY electric pump ...................................................................................................................................................... 27
3.5.5 Shut-off valve ............................................................................................................................................................... 28
3.5.6 Battery charger ............................................................................................................................................................ 28
3.5.6.1 BC0512.................................................................................................................................................................... 29
3.5.6.2 BC0524.................................................................................................................................................................... 31
3.5.6.3 BC1012.................................................................................................................................................................... 33
3.5.6.4 BC1024.................................................................................................................................................................... 35
3.5.6.5 BC2024.................................................................................................................................................................... 37
4 Handling .................................................................................................................................................................................... 39
4.1 Unloading the equipment ................................................................................................................................................. 40
4.2 Moving the equipment using slings .................................................................................................................................. 40
4.2.1 Display of lifting points ................................................................................................................................................. 41
4.3 Moving the equipment using a forklift truck ...................................................................................................................... 42
4.3.1 Handling generating sets with and without an enclosure ............................................................................................. 42
4.3.2 Handling containerised generating sets ....................................................................................................................... 42
4.4 Moving the equipment using a mobile winch .................................................................................................................... 43
4.5 Moving equipment by rollers or dolly systems .................................................................................................................. 43
5 Transporting and storing the generating set.............................................................................................................................. 44
5.1 Preparing for transport ..................................................................................................................................................... 44
5.2 Road transport.................................................................................................................................................................. 44
5.2.1 ADR regulations concerning the transport of dangerous materials .............................................................................. 44
5.2.2 Generating sets with and without an enclosure............................................................................................................ 45
5.2.3 Containerised generating sets ..................................................................................................................................... 46
5.3 Rail transport .................................................................................................................................................................... 47
5.3.1 Generating sets with and without an enclosure............................................................................................................ 47
5.3.2 Containerised generating sets ..................................................................................................................................... 47
5.4 Shipping ........................................................................................................................................................................... 47
5.4.1 Generating sets with and without an enclosure............................................................................................................ 47
The documentation supplied with the generating sets defines all operating and maintenance operations for the generating set or
power station, as well as instructions for the safety and protection of people and equipment. This reference documentation is designed
to help you become familiar with the equipment, operate and maintain it, and conduct daily and periodic servicing. It consists of the
following elements:
- The instructions and safety regulations to be respected for the protection of persons,
- The generation set's technical specifications (data sheet),
- The general recommendations containing, among other things:
the transport and handling indications,
the general rules for installing generating sets,
general instructions for preparing generating sets prior to their commissioning,
the specifications for fuel, lubricants and coolants to be used,
special maintenance instructions,
maintenance specifications and/or instructions for certain optional equipment.
- The operating instructions for the control unit (if equipped),
- The operating and maintenance manual for the engine fitted to the generating set*,
- The maintenance manual for the alternator fitted to the generating set*,
- The electrical diagrams (separate document or included in the documentation, as the case may be).
The information and references contained in the manuals are taken from technical data available at the time of print (the photos
shown in our manuals are not legally binding). In line with our policy of continually improving the quality of our products, this information
may be amended without warning.
* The reference documents for the engines and alternators fitted to the generating sets consist of engine operating and maintenance
manuals (provided by the manufacturer) and alternator operating and maintenance manuals (also provided by the manufacturer).
Certain operating and maintenance manuals of the engines powering the generating sets have control units and indicate the engine
start-up and shut-down procedures: as our generating sets are equipped with specific control units, only the information provided in
the documentation of the control units equipping our generating sets are to be taken into consideration.
In addition, depending on the manufacturing criteria of the generating sets, some engines may be fitted with specific electrical wiring
different from that described in the engine documentation.
In this manual, the warning messages are used in the following manner:
Immediate danger.
Indicates an imminent danger which may result in death or serious injury. Failure to follow the instruction
shown may pose serious risks to the health and life of those concerned.
DANGER
Potential danger.
Indicates a dangerous situation if the warning is not heeded. Failure to follow the instruction indicated may
cause minor injuries to those concerned or damage to equipment.
IMPORTANT
The left and right sides can be seen from the back of the generating set (the radiator is at the front). Abbreviations and terms defined
in the glossary and references to figures and chapters are shown in italics.
Carefully read the entire generating set operating and maintenance manual and safety instructions. It is essential that the instructions,
safety regulations and current legislation be respected.
If you have any doubts regarding the instructions or recommended operations, please contact your nearest agent. Our dealers are
highly qualified and can answer all of your questions. They can also supply spare parts and other services. They also have trained
staff to carry out preventive and corrective maintenance on generating sets and even ensure their complete overhaul.
All operations not specified in the generating set's documentation are prohibited; no settings are to be modified if not expressly
stipulated in the documentation. Ensure that all operations are carried out by personnel who have received appropriate training. Never
let other people use the generating set without having given them all the necessary instructions beforehand. Never let a child touch
the generating set, even when not in operation.
In all cases, respect the local regulations currently in place concerning the use of generating sets.
Important: Important:
Important:
rotating or moving danger, automatic Draining fuel. Draining oil. Draining coolant.
high temperature.
parts. start.
Danger: Important:
Consult the Sight and hearing Do not open the Open the doors
Sight protection Battery isolating
information protection doors when the before starting
compulsory. switch.
guide. compulsory. generating set is the generating
operating. set.
- Personnel protection:
o Wear suitable clothing and protective goggles.
o Remove any personal belongings that may hinder the operation: watch, bracelet, etc.
o Fit a panel over the controls of the equipment to prevent any attempt to start.
o Disconnect the battery (and pneumatic starter if fitted) before beginning any maintenance operation.
o Handle the equipment according to best practices, using techniques which do not endanger the personnel.
o It is essential to wear gloves when detecting leaks.
o Regularly check that the safety devices are operating correctly.
Note: the mounting bolts on the protective devices of the rotating parts are captive bolts equipped with retaining washers.
Also, in order to ensure the integrity of this assembly, it is prohibited to use electric or pneumatic screwdrivers to undo
these mounting bolts.
- Additional instruction:
o If necessary, contact the dealer for the following reasons:
answers to any questions relating to the equipment;
training requests for personnel;
supplying the relevant documentation for maintenance operations;
supplying spare parts;
corrective or preventive maintenance operations.
Operating site
- Maintenance:
o Clean the entire operating site regularly with suitable cleaning materials.
o The presence of dangerous or combustible materials inside premises must be limited to the operating requirements.
- Access:
o Prohibit free access to persons who are not part of the establishment, except for those designated by the user.
DANGER
- Select the appropriate handling equipment and apparatus according to the type of equipment being handled. Check that
there is sufficient handling capacity.
- Check that the handling equipment and apparatus are in good operating condition.
- Respect the handling instructions described in the present documentation and the pictograms displayed on the equipment
to be handled.
- Be sure never to stand under the load being handled.
Note: the lifting rings provided on the equipment are designed to handle the generating set alone. If additional equipment is fitted to
the generating set, a study should be conducted in order to define the centre of gravity of the assembly and to check the correct
mechanical performance of the structure and its lifting rings.
DANGER
- Read the manufacturer's identification plate carefully. The values for voltage, power, current and frequency are shown.
Check that these values match the installation being supplied.
- The electrical connections must be made in accordance with current standards and regulations in the country of use and the
neutral system sold.
- Ask a qualified electrician to intervene when there are specific cases requiring equipment to be connected to an existing
electrical network.
- Disconnect the power to the equipment (equipment voltage, battery voltage and network voltage) before any installation or
maintenance operation is performed.
- Connect the equipment wires by respecting the wiring diagram supplied by the manufacturer.
- Always handle the equipment with dry hands and feet.
- Take all the necessary precautions to avoid touching stripped cables or disconnected connectors.
- Use and maintain the cables in good condition, well insulated and connected correctly and securely.
- Only replace equipment that provides protection against electric shock with identical equipment (specifications and nominal
values).
- Only use flexible durable cables with a rubber covering, which conform to ECI 245-4, or equivalent cables.
- Refit the protective plates (blanking covers) after each maintenance operation.
Note: The electrical equipment supplied with the equipment complies with standard NF C15.100 (France), or with the standards of
the countries in question.
1. Avoid direct contact both with the live conductor and the victim's body.
2. Shut off the power immediately and activate the emergency stop for the equipment concerned. Note:
the live wire may be cut with an axe. Take extreme care to avoid the electric arc that will be generated
by this.
3. If it is impossible to access the equipment: move the victim away from the live conductor using a dry
piece of wood, dry clothing or other non-conducting material.
4. Move the victim away from any situations where there is a danger of death.
5. Contact the emergency services.
6. If breathing has stopped, begin artificial respiration at once.
7. In the event of cardiac arrest, carry out cardiac massage.
- RISK OF BURNS -
- RISK OF FIRE -
DANGER - RISK OF EXPLOSION -
1. Before starting the equipment, move any flammable or explosive products away (petrol, oil, cloth, etc.).
2. It is prohibited to put combustible materials on the hot parts of the equipment (for example: exhaust pipe).
3. Avoid any contact with the hot parts of the equipment (for example: exhaust pipe).
4. Use appropriate ventilation to allow the equipment to cool correctly.
5. Wait for the engine to stop and cool down completely before removing the radiator cap.
6. Wait for the equipment to stop and cool down completely before covering the equipment (if necessary).
7. Depressurize the air, oil and cooling circuits before removing or disconnecting all the fittings, pipes or connected components.
When installing the equipment on a vehicle or other mobile equipment, a study must be conducted beforehand in
order to take into account the various specific uses of the generating set.
IMPORTANT
Fuels
- Respect current local regulations regarding the equipment and fuel used (petrol, diesel and
gas).
- Top up the engine with fuel when the engine has stopped (except for equipment with an
automatic filling system).
- Smoking, using a flame or producing sparks are forbidden while the fuel tank is being filled.
- Use protection suitable against fires and explosions.
- Pipes must be replaced as soon as their condition demands it.
Oils
1. Check that the system is no longer pressurized before carrying out any procedures.
2. Avoid contact with hot oil.
3. Wait for the engine to stop and cool down completely before topping up the oil.
4. Before starting the engine, refit the oil filler cap.
5. It is prohibited to cover the generating set with a fine layer of oil for anti-rust protection.
Battery
Smoking, using a flame or producing sparks are forbidden close to batteries (particularly when the batteries are being charged).
DANGER
Exhaust gas
- Use suitable ventilation to release the exhaust gas outside and prevent it from accumulating.
- Respect current local regulations regarding the equipment and fuel used (petrol, diesel and gas).
- Periodically examine the burnt gas exhaust.
- Pipes must be replaced as soon as their condition demands it.
Note: the carbon monoxide present in the exhaust gas may lead to death by inhalation if the concentration levels in the atmosphere
are too high.
Battery electrolyte
- Avoid all contact with the skin and eyes.
- Wear suitable protective goggles and clothing and strong alkali-resistant gloves
for handling the electrolyte.
DANGER
- Always use suitable ear defenders when working in close proximity to a generating set which is in operation.
- The sound pressure level measured at 1 m is indicated on the generating set's nameplate.
Note: For generating sets operating indoors, for which the ambient noise levels are dependent upon the installation conditions, it is
not possible to specify these ambient noise levels in the operating instructions. As prolonged exposure to high sound pressure levels
can cause permanent damage to hearing, acoustic measurements must be performed after installation in order to determine the
sound pressure level and, if necessary, to implement the appropriate preventive measures.
Generating sets and their components are identified by means of identification plates.
The precise rules for identifying each major component (engine, alternator, etc.) are set out in each manufacturer's documentation
contained in the appendices of this manual. 16
1
3
17
2
14
12 10 11 7 15
13 9 8
5 4 18
1 - Generating set
2 - Manufacturer name 9 - Maximum ambient temperature for the rated power (°C)
3 - Model 10 - Rated frequency (Hz)
4 - Serial number 11 - Generating set rotation speed (RPM)
5 - Year of manufacture 12- Rated voltage (V)
6 - Rated output (kVA and kW) according to the ISO 8528-1 13 - Rated current (A)
standard 14 - Weight (kg)
PRP: main power 15 - CE marking
ESP: emergency power 16 - Non CE standard marking (e.g.: EAC)
7 - Rated power factor 17 - Sound pressure
8 - Maximum altitude of the site above sea level (m) for the 18 - Sound power
rated power
The identification plate for generating sets with and without protective covers is affixed to the lower section of the base frame.
Identification plate
Figure 2: Position of the identification plate for generating sets with and without protective covers
Identification plate
5 2
12
11
10
1
2
6
3
15
8
14
13
10
12
11
1
2
14
7
13
6 10
12
16
15 11
Lights
Column
Trailer
The term ‘HC’ makes reference to “High Cube” containers which are high-capacity and have a greater height. The term ‘Dry’
designates standard height containers.
*ISO (making reference to ISO dimensions) - CIR ("Conteneur Industriel et Rental", Industrial and Rental Container) - CPU
(Containerised Power Unit)
ISO 20 and ISO 40 20' and 40' containers comply with the ISO/TC104 standards and are CSC1 certified, i.e. authorised for shipping.
Silencer
Console
AIPR
Sound trap
Soundproofed
Radiator air inlet grille
Fuel tank
Silencer
Sound trap
Soundproofed
air inlet grille
AIPR
Radiator
CPU 20 and CPU 40 containers are compact generating sets designed for low noise level and exceptional accessibility. The
dimensions and ISO corners of these models allow ISO transport and handling equipment to be used.
Sound traps
CIR 20 containers (not C.S.C. certified) are built based on ISO 20 containers (compliant with ISO/TC104 on request).
These low noise level containers are well-suited to mobile and rental applications.
NOTE: The non-retention zone must be in the open air: do not plug the side drainage openings.
Radiator
Muffler
Soundproof air
inlet grille
Non-retention zone
All container generating sets (20' and 40') are available on a trailer.
Any outflow of the fluid contained in the generating sets (fuel, oil and coolant) will be collected in a retention container if the generating
set is fitted with this option.
The containers have a capacity which allows 110% of the fluids contained in the generating set fitted with this option to be collected.
Three different fittings are available:
Fitting 1: Fluid retention container Fitting 2: Offset fluid retention container Fitting 3: Offset fluid retention container
integrated into the tank frame underneath the generating set frame integrated into the frame and tank
Note: generating sets equipped with the option corresponding to fitting 3 (see Figure: Integrated fluid retention container) are also
equipped with a high level indicator in the retention container.
In all cases, the retention containers must be regularly checked to ensure they contain no fluid (fuel, oil and coolant, or rainwater or
condensation). If necessary, drain the containers either via the drain port or using the drain pump (for containers fitted with this pump).
Drain the fluids from the retention container into a designated container.
It is prohibited to perform this drain procedure on the ground.
IMPORTANT
The REN regulator type RAB 101 -70 is an oil level regulator for all engine power ratings. It keeps the oil level in the crankcase
correct. Set to "engine running" oil level, it regulates the level in line with consumption.
Most models have a low level alarm or stop threshold to inform the user about insufficient oil supply, a drop in the crankcase oil level
or potential overfilling.
An integrated oil level threshold triggers an alarm or stops the engine and warns the user that there is an insufficient oil supply, whilst
the engine continues to consume.
3.5.2.2 Operation
When the crankcase oil level drops, the float drops and opens the valve.
The open valve allows oil to flow through from the tank to the crankcase via the regulator.
When the desired level is reached in the crankcase, the regulator float rises which causes the valve to close and stops the flow.
The valve has been designed to be self-cleaning and cannot clog.
A 3 mm hole in the regulator is large enough to allow the oil sump to be topped up.
Oil supply
TOP
Float
action
Separation of
unit LR857
BOTTOM
Low level
contacts
Diesel
HV
Oil 1. Lever
3. Piston + valves + pins
4. Seat + valves + pins
5. Body
6. Fittings and seals
7. Felt seal + O-ring + fittings
8. Cap
EZ Diesel
The maximum pressure in the body of the pump should not exceed 10bars. Normal use of the pump should not require any major
effort by the operator during pumping.
In case of major difficulty using the lever during pumping, do not force it, and check to make sure there are no foreign bodies in the
suction circuit, drain the pump. If the difficulties persist, contact one of our agents.
The hourly flow rates are given at the indicated double stroke rate and for a full range of movement of the lever, 1 metre suction, 1
metre discharge, free flow.
Suction capacity is independent of the size of the pump. A size 0 pump and a size 5 pump have the same suction capacity. These
pumps can achieve 7 meters of suction with cold water, at sea level, and with a foot flap. It is advisable to check installation conditions
for suction : Ø of pipe and length.
The presence of air in the circuit limits the suction capacity of the pump. To avoid any air ingress, all joints must be perfectly sealed
and the piping must have no cracks or porosity.
Technical data:
Electrical data:
- Power: 0.37 kW
- Engine made for continuous work
Usable fluids
Prohibited fluids
Damper valves are safety components which close automatically and are reset manually.
SHUT-OFF VALVE
Wear gloves and take care operating the damper valves: risk of injury.
DANGER
To reset:
1. Hold the lever or position the spanner on the hexagon shape (we recommend using a ring spanner for improved ergonomics).
2. Slowly but firmly, turn in the direction indicated below until it is possible to feel it lock into place.
3. Gradually release the pressure: the valve should remain open.
Lever
19 hexagon 17 hexagon Lever or 19 or 22 hexagon
depending on model
Battery chargers are charging modules for emergency electrical supplies, adapted to equipment and systems with inrush currents:
relays, motors, solenoid valves, automata, audible warning devices, etc. and their constant monitoring, signalling, inspection and
control circuits or designed to charge accumulator batteries.
These charger modules associated with batteries comprise battery charger assemblies which make each system safe in the event of
mains supply faults.
They permanently supply the equipment (monitoring, signalling, inspection and control) and ensure that the batteries are maintained.
Features
DC voltage 12 V
Rated current 5A
Current range 0~5A
Rated power 60 W
Ripple & Noise (max.) 120mVp-p
Voltage adj. Range 12 ~ 15 V
OUTPUT
Line regulation (+/-) 1.0%
Load regulation (+/-) 1.0%
Setup, rise time 500ms, 30ms/230VAC 500ms, 30ms/115VAC at full load
Hold up time (typ.) 50ms/230VAC 20ms/115VAC at full load
Please adjust output voltage required with the potentiometer according to
Information
the battery charger
Voltage range 85 ~ 264VAC 120 ~ 370VDC
Frequency range 47 ~ 63Hz
Efficiency (typ.) 86%
INPUT
AC current (typ.) 1.8A/115VAC 1A/230VAC
Inrush current (typ.) Cold start 30A/115VAC 60A/230VAC
Leakage current <1mA / 240VAC
105 ~ 150% rated output power
Overload Protection type: constant current limiting recovers automatically after fault
PROTECTION condition is removed
15.6 ~ 18V
Over voltage
Protection type : shut down o/p voltage, re-power on to recover
FUNCTIONS Fault relay contact Relay contact ratings (max.) 30V/1A resistive Contact closed = fault
Working temp. (-)20 ~ (+)70°C (refer to output load derating curve)
Working humidity 20 ~ 90% RH non condensing
Storage temp, humidity (-)40 ~ (+)85°C, 10 ~ 95% RH
ENVIRONMENT
Temp. Coefficient (+/-)0.03%/°C (0 ~ 50°C)
Component: 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along
Vibration
X, Y, Z axes ; Mounting: Compliance with IEC60068-2-6
Safety standards UL508, UL60950-1, TUV EN60950-1 approved
Withstand voltage I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
Isolation resistance I/P-O/P, I/P-FG, O/P-FG:>100M Ohm / 500VDC / 25°C / 70% RH
SAFETY
& EMC Emi conduction & radiation Compliance with EN55011, EN55022 (CISPR22), EN61204-3 Class B
Harmonic current Compliance with EN61000-3-2,-3
Compliance with EN61000-4-2, 3, 4, 5, 6, 8, 11, ENV50204, EN55024,
Protections EMS
EN61000-6-2, EN61204-3, heavy industry level, criteria A
MTBF 299.2Khrs min MIL-HDBK-217F (25°C)
OTHERS Dimension 40 x 90 x 100mm (W x H x D)
Packing 0.33kg; 42pcs/14.8kg/0,82CUFT
All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient
temperature.
Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair wire terminated with a 0.1µF
& 47% µF parallel capacitor.
NOTES
The power supply is considered a component which will be installed into a final equipment. The final
equipment must be re-confirmed that it still meets EMC directives
Length of set up time is measured at cold first start. Turning ON/OFF the power supply very quick may lead
to increase of the set up time.
Block diagram
Features
DC voltage 24 V
Rated current 5A
Current range 0~5A
Rated power 120 W
Ripple & Noise (max.) 120mVp-p
Voltage adj. Range 24 ~ 29 V
OUTPUT
Line regulation (+/-) 0.5%
Load regulation (+/-) 0.5%
2000ms, 70ms, 50ms/400VAC
Setup, rise, hold up time
2000ms, 70ms, 10ms/230VAC at full load
Please adjust output voltage required with the potentiometer according to the
Information
battery charger type before the commissioning
Voltage range 180 ~ 550VAC 254 ~ 780VDC
Frequency range 47 ~ 63Hz
Efficiency (typ.) 91% / 400V
INPUT
AC current (typ.) 0.55A/400VAC 1.2A/230VAC
Inrush current (typ.) Cold start 50A
Leakage current <3.5mA / 530VAC
105 ~ 130% rated output power
Overload Protection type: constant current limiting, recovers automatically after fault
condition is removed.
31 ~ 37V
PROTECTION Over voltage
Protection type : shut down o/p voltage, re-power on to recover
110°C (+/-)5°C (TSW1)
Over temperature Protection type : shut down o/p voltage, recovers automatically after
temperatures goes down
Relay contact rating(max.): 30V / 1A resistive Contact open = DC OK / Contact
Fault relay contact
FUNCTIONS closed = DC NOK
Boos mode Contact closed = boost mode Boost voltage =+4% above floating voltage
Working temp. (-)25 ~ (+)70°C (refer to ouput load derating curve)
Working humidity 20 ~ 90% RH non condensing
Storage temp, humidity (-)40 ~ (+)85°C, 10 ~ 95% RH
ENVIRONMENT
Temp. Coefficient (+/-)0.03%/°C (0 ~ 50°C)
Component: 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y,
Vibration
Z axes ; Mounting: Compliance with IEC60068-2-6
SAFETY Isolation resistance I/P-O/P, I/P-FG, O/P-FG:100M Ohm / 500VDC / 25°C / 70% RH
& EMC
EMI conduction & Compliance with EN55011 (CISPR11), EN55022 (CISPR22), EN61204-3 Class
radiation B
Compliance with N61000-4-2,3,4,5,6,8,11, ENV50204, EN61204-3, EN61000-
EMS immunity
6-2 (EN50082-2), heavy industry level, criteria A.
MTBF 268Khrs min MIL-HDBK-217F (25°C)
OTHERS
Dimensions 40 x 125.2 x 113.5mm (W x H x D)
Packing 0.65Kg; 20pcs/14Kg/1.16CUFT
All parameters NOT specially mentioned are measured at 400VAC input, rated load and 25°C of ambient
temperature.
Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair wire terminated with a
NOTES 0.1µF & 47 % µF parallel capacitor.
The power supply is considered a component which will be installed into a final equipment. The final
equipment must be re-confirmed that it still meets EMC directives
Length of set up time is measured at cold first start. Turning ON/OFF the power supply very quick may lead
to increase of the set up time.
Block diagram
Features
DC voltage 12 V
Rated current 10 A
Current range 0 ~ 10 A
Rated power 120 W
Ripple & Noise (max.) 120mVp-p
OUTPUT Voltage adj. Range 12 ~ 15 V
Line regulation (+/-) 0.5%
Load regulation (+/-) 0.5%
Setup, rise time 2000ms, 70ms, 50ms/400VAC - 2000ms, 70ms, 10ms/230VAC at full load
Hold up time (typ.) Please adjust output voltage required with the potentiometer according to the battery
charger type before the commissioning
Voltage range 180 ~ 550VAC - 254 ~ 780VDC
Frequency range 47 ~ 63Hz
Efficiency (typ.) 89.5% / 400V
INPUT
AC current (typ.) 0.55A/400VAC 1.2A/230VAC
Inrush current (typ.) Cold start 50A
Leakage current <3.5mA / 530VAC
105 ~ 130% rated output power
Overload Protection type: constant current limiting recovers automatically after fault condition is
removed
PROTECTION
16 ~ 18V
Over voltage
Protection type : shut down o/p voltage, re-power on to recover
Over temperature 105°C (+/-)5°C (TSW1)
Fault relay contact Protection type : shut down o/p voltage, recovers automatically after temperatures
goes down
FUNCTIONS
Boost mode Relay contact rating (max.): 30V / 1A resistive - Contact open = DC OK / Contact closed
= DC NOK
Working temp. Contact closed = boost mode - Boost voltage =+4% above floating voltage
Working humidity (-)25 ~ (+)70°C (refer to output load derating curve)
ENVIRONMENT Storage temp, humidity 20 ~ 90% RH non condensing
Temp. Coefficient (-)40 ~ (+)85°C, 10 ~ 95% RH
Vibration (+/-)0.03%/°C (0 ~ 50°C)
Safety standards Components: 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z
axes ; Mounting : Compliance with IEC60068-2-6
Withstand voltage UL508 approved
SAFETY
& EMC Isolation resistance I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC O/P-DC OK:0.5KVAC
EMI conduction &
I/P-O/P, I/P-FG, O/P-FG:100M Ohm / 500VDC / 25°C / 70% RH
radiation
EMS immunity Compliance with EN55011 (CISPR11), EN55022 (CISPR22), EN61204-3 Class B
MTBF Compliance with EN61000-4-2,3,4,5,6,8,11, ENV50204, EN61204-3, EN61000-6-2
(EN50082-2), heavy industry level, criteria A
OTHERS
Dimension 40 x 125.2 x 113.5mm (L x H x P)
Packing 268Khrs min MIL-HDBK-217F (25°C)
All parameters NOT specially mentioned are measured at 400V AC input, rated load and 25°C of ambient
temperature.
Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair wire terminated with a 0.1 µF &
47 µF parallel capacitor.
NOTES
The power supply is considered a component which will be installed into a final equipment. The final equipment
must be re-confirmed that it still meets EMC directives
Length of set up time is measured at cold first start. Turning ON/OFF the power supply very quick may lead to
increase of the set up time.
Block diagram
Features
DC voltage 24 V
Rated current 10 A
Current range 0 ~ 10 A
Rated power 240 W
Ripple & Noise (max.) 150mVp-p
Voltage adj. Range 24 ~ 28 V
OUTPUT
Line regulation (+/-) 0.5%
Load regulation (+/-) 1%
Setup, rise time 800ms, 150ms/400VAC 1500ms, 150ms/230VAC at full load
Hold up time (typ.) 18ms / 400VAC 18ms / 230VAC at full load
Information Please adjust output voltage required with the potentiometer according to the battery
charger type before the commissioning
Voltage range 180 ~ 550VAC 254 ~ 780VDC
Frequency range 47 ~ 63Hz
Efficiency (typ.) 91%
INPUT
AC current (typ.) 1A/400VAC 2A/230VAC
Inrush current (typ.) Cold start 50A
Leakage current <3.5mA / 530VAC
105 ~ 130% rated output power
Overload Protection type : Constant current limiting, unit will shut down after 3 sec., auto-recovery
after 1 minute if the fault condition is removed
29 ~ 33V
PROTECTION Over voltage Protection type : Shut down o/p voltage, auto-recovery after 1 minute if the fault condition
is removed
90°C (+/-)5°C (TSW1)
Over temperature Protection type : shut down o/p voltage, recovers automatically after temperatures goes
down
60VDC/0.3A, 30VDC/1A, 30VAC/0.5A resistive load - Contact open = DC OK / Contact closed
Fault relay contact
= DC NOK
FUNCTIONS
Contact closed = boost mode
Boos mode
Boost voltage =+4% above floating voltage
Working temp. (-)30 ~ (+)70°C (refer to output load derating curve)
Working humidity 20 ~ 95% RH non condensing
Storage temp, humidity (-)40 ~ (+)85°C, 10 ~ 95% RH
ENVIRONMENT
Temp. Coefficient (+/-)0.03%/°C (0 ~ 50°C)
Vibration Components: 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes ;
Mounting: Compliance with IEC60068-2-6
Safety standards UL508 approved, IEC60950-1 CB approved by SIQ, design refer to GL
Withstand voltage I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC O/P-DC OK:0.5KVAC
SAFETY Isolation resistance I/P-O/P, I/P-FG, O/P-FG:100M Ohm / 500VDC / 25°C / 70% RH
& EMC Emi conduction &
radiation Compliance with EN55011 (CISPR11), EN55022 (CISPR22), EN61204-3 Class B
Block diagram
Features
DC voltage 24 V
Rated current 20 A
Current range 0 ~ 20 A
Rated power 480 W
Ripple & Noise (max.) 100mVp-p
Voltage adj. Range 24 ~ 28 V
OUTPUT
Line regulation (+/-) 0.5%
Load regulation (+/-) 1%
Setup, rise time 800ms, 150ms/400VAC 2000ms, 150ms/230VAC at full load
Hold up time (typ.) 18ms / 400VAC 16ms / 230VAC at full load
Information Please adjust output voltage required with the potentiometer according to the battery
charger type before the commissioning
Voltage range 180 ~ 550VAC 254 ~ 780VDC
Frequency range 47 ~ 63Hz
Efficiency (typ.) 92%
INPUT
AC current (typ.) 1.6A/400VAC 4A/230VAC
Inrush current (typ.) Cold start 50A
Leakage current <3.5mA / 530VAC
105 ~ 130% rated output power
Overload Protection type : Constant current limiting, unit will shut down after 3 sec. , auto-
recovery after 1 minute if the fault condition is removed
29 ~ 33V
PROTECTION Over voltage Protection type : Shut down o/p voltage, auto-recovery after 1 minute if the fault
condition is removed
95°C (+/-)5°C (TSW)
Over temperature Protection type : shut down o/p voltage, recovers automatically after temperatures
goes down
60VDC/0.3A, 30VDC/1A, 30VAC/0.5A resistive load Contact open = DC OK / Contact
Fault relay contact
FUNCTIONS closed = DC NOK
Boost mode Contact closed = boost mode -Boost voltage =+4% above floating voltage
Working temp. (-)30 ~ (+)70°C (refer to ouput load derating curve)
Working humidity 20 ~ 95% RH non condensing
Storage temp, humidity (-)40 ~ (+)85°C, 10 ~ 95% RH
ENVIRONMENT
Temp. Coefficient (+/-)0.03%/°C (0 ~ 50°C)
Vibration Components: 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z
axes ; Mounting: Compliance with IEC60068-2-6
Safety standards UL508 approved, IEC60950-1 CB approved by SIQ, design refer to GL
Withstand voltage I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC O/P-DC OK:0.5KVAC
SAFETY Isolation resistance I/P-O/P, I/P-FG, O/P-FG:100M Ohm / 500VDC / 25°C / 70% RH
& EMC Emi conduction &
radiation Compliance with EN55022 (CISPR22), EN61204-3 Class B, EN61000-3-2,-3
Block diagram
Some generating sets are equipped with transport brackets, which are red,
facilitating their movement and transportation.
It is essential to remove the transport brackets before the generating set
concerned is installed in its final position.
Lifting a lighting column with the lifting ring fixed to the generating set is
prohibited; use the 4 lifting rings on the trailer.
IMPORTANT
Certain generating sets cannot be handled using the lifting ring mounted on the
enclosure or can only be handled when the fuel tank is empty: follow the
instructions on the sticker, as the case may be. If you have any doubt, please
contact one of our agents.
To unload the equipment from its transportation support, observe the following steps:
1. Select the unloading site for the equipment, in accordance with the following criteria:
- The proximity between the unloading site and the equipment's operating location;
- Ease of access to the equipment for the movement stages;
- Ease of movement between the unloading site and the location where the equipment will be used;
- The ability of the ground to support the load of the equipment and its handling apparatus.
2. Correctly place the transport support and the handling apparatus (crane, forklift, etc.).
3. If the transport support must be moved, make sure that the equipment to be handled is correctly secured.
4. If the ground does not have the prerequisites to support the load of the equipment and its handling apparatus, fit beams or
load distribution plates that are designed to support the entire load.
5. Select the appropriate method, handling equipment and apparatus according to the type of equipment being handled. Check
that the handling capacity is sufficient (weight and jib distance required to place the equipment).
6. Carefully read the instructions relating to the handling methods in the section entitled "Equipment handling" in this document
and call upon a professional to assist you.
IMPORTANT
Generating set with 4 fork pockets Generating set with 4 lifting brackets
Enclosure with 1 lifting ring Enclosure with 2 lifting brackets Enclosure with 4 lifting brackets
sling length
or
enclosure width
WARNING
Maximum sling angle for enclosed generating sets with lifting brackets
Container
X4
IMPORTANT
Use a forklift truck with forks that are longer than the width of the frame.
IMPORTANT
1. Position the forklift's forks under the frame (except with generating sets fitted with "forklift pockets", in which case position
the forks in these pockets), making sure that only its cross members are resting on the forks.
2. Lift the equipment, handling it gently.
3. Set down the generating set in its unloading location.
Only containers equipped with forklift pockets are authorised for handling.
Each forklift pocket area of the generating set is marked by a pictogram.
IMPORTANT
Use a forklift truck with forks that are longer than the width of the frame.
IMPORTANT
If you are using a room equipped with a suitable rail or mobile winch, proceed as described in the paragraph "Moving the equipment
by hoisting".
Use equipment that is in good condition and suited to the material to be moved.
In the event a cable ratchet is used during rolling operations, an appropriate braking system in keeping with the load must be
implemented.
Only generating sets that do not have brackets built into the frame can be moved using rollers or dolly
systems.
The base frame support surface on the rollers must not be deformed.
IMPORTANT
IMPORTANT
All transport operations must be carried out in compliance with the current regulations of the countries concerned.
Prior to all transport operations:
- Check the overall condition of the generating set and ensure that all threaded fasteners are tight;
- Check that all valves on the generating set are correctly closed (drain valve, fuel valve, etc.);
- Check for leaks;
- Protect the generating set so that it is not damaged during transport.
Certain elements of the generating set (exhaust stack, spark arrestor, exhaust extension, air conditioner, cooling towers, etc.) must
sometimes be dismantled for transport: protect them during their transport, plug their installation location and ensure that they are put
correctly back into place upon delivery.
- Where the means of containment has a capacity greater than 1,500 litres, the machinery or equipment
is placarded on all four external sides [...] and the transport document includes the following additional
statement: ‘Carriage in accordance with special provision 363’.
44 Section 5 Transporting and storing the generating set 33532000201_6_1 MGS_186_EN _17/07/2017 15:01
5.2.2 Generating sets with and without an enclosure
When transporting generating sets by road, the following steps must be observed:
1. Select transport equipment (trailer, semi-trailer, etc.) suitable for this usage and which has all the safety guarantees in terms
of load bearing capacity and of the securing devices.
2. Place the generating set on the transport equipment: it should preferably be positioned over the axles and centred so as to
balance the load.
3. Chock and secure the generating sets to the deck of the transport equipment or use non-slip pads at the four corners of the
genset.
4. Strap the generating sets to their transport equipment, ensuring that their placement does not risk damaging the equipment
during transport.
For generating sets equipped with a towbar, the strap can be placed around the towbar.
5. Select a transport route which makes it possible to travel on roads suitable for vehicles, and whose quality will not damage
the on-board generating sets.
20° - 30°
MGS_186_EN _17/07/2017 15:01 33532000201_6_1 Section_5 _Transporting and storing the generating set 45
1. Place the slings over the top of 20° - 30°
the enclosure, on each side of the
lifting brackets.
20° - 30°
Figure 26: Example of recommended lashings for generating sets with protective enclosures
When transporting generating sets in containers on roads, the following steps must be observed:
1. Select transport equipment (container carrier) suitable for this usage and having all the safety guarantees in terms of load
bearing capacity and securing devices.
2. Select a transport route which makes it possible to travel on roads suitable for vehicles, and whose quality will not damage
the container or its contents.
46 Section 5 Transporting and storing the generating set 33532000201_6_1 MGS_186_EN _17/07/2017 15:01
5.3 Rail transport
Generating sets must be transported by rail in accordance with the specific rules governing rail transport.
For the transport of generating sets by rail, choose transport equipment appropriate for this usage, and having all the safety
guarantees both in terms of load-bearing capacity and securing devices.
Containers transported by rail must comply with the specific rules governing rail transport.
Containers must receive the necessary approvals for rail transport.
When transporting generating sets in containers by rail, choose transport equipment appropriate for this usage and having all the
guarantees in terms of load-bearing capacity and securing devices.
5.4 Shipping
We strongly recommend that maritime containers be used to transport the generating sets. Choose the appropriate transport
equipment having all the safety guarantees in terms of protection, load-bearing capacity and securing devices. In the case of an LCL
(less-than-container-load) container, elements must be packed in SEI crates.
The transport of certain elements of the generating set or the installation must often be organised separately.
This involves, for example:
- For generating sets: exhaust stacks, cooling towers and other bulky components which must sometimes be dismantled for
transport, or spare parts.
- For installations: electrical cabinets, transformers, terrace-mounted cooling towers and other electrical or mechanical
components.
These components must be packaged in at least a SEI 4 shipping container, with category C protection (solid case under waterproof
cover) for electrical equipment.
MGS_186_EN _17/07/2017 15:01 33532000201_6_1 Section_5 _Transporting and storing the generating set 47
5.6 Generating sets on trailers
ACCIDENT RISK
Before each use, check overall condition of the trailer and the fastening of the generating set.
At all times, ensure that:
- The manoeuvre cannot injure someone.
- No one is near the vehicle when it is being moved or its mobile elements are in use.
Perform the technical inspections required by current regulations.
The original adjustments must be maintained and checked by specialists.
It is essential that the instructions, safety regulations and current legislation be respected.
Any attempt to tow a trailer with a non-compliant device (bar, cables, lashing, etc.) runs the risk of
DANGER serious accidents.
5.6.2 Description
5.6.2.2 Hitches
48 Section 5 Transporting and storing the generating set 33532000201_6_1 MGS_186_EN _17/07/2017 15:01
5.6.2.3 Signalling
The trailer is equipped with a lighting device in compliance with European Directive 76/756/CE.
Lights/signalling (only for "on-road" trailers)
Warning lights are mandatory for on-road driving. Signalling must comply with current regulations in the country of use.
5.6.2.4 Limits
Speed limits:
Our trailers are approved for a maximum speed of 140 km/h on roads suitable for vehicular traffic.
Our trailers are not designed for all-terrain use.
Specific limitation: road signs
Speed limits over obstacles (height / speed):
- Curb: 30 cm at 5 km/h
- Speed bump: 10 cm at 30 km/h
MGS_186_EN _17/07/2017 15:01 33532000201_6_1 Section_5 _Transporting and storing the generating set 49
5.6.3 Use
The trailer must be hitched horizontally, particularly concerning dual-axle trailers. All 4 wheels must be in contact with the ground.
CORRECT CORRECT
véhicule
Towing vTowing
éhicule
tracteur
vehicle remorque tvehicle
racteur remorque
Trailer Trailer
INCORRECT INCORRECT
Towing
véhicule vTowing
éhicule
vehicle
tracteur tvehicle
racteur
remorque
Trailer
remorque
Trailer
The brake controls are designed to pull trailers behind passenger vehicles with soft suspension. If used behind an
HGV, the ball hitch must be fitted with a damper to prevent premature wear.
WARNING
50 Section 5 Transporting and storing the generating set 33532000201_6_1 MGS_186_EN _17/07/2017 15:01
5.6.3.1 Verifications prior to hitching
The trailer may become unhitched from the tow vehicle if not hitched correctly. The release cable will engage
the parking brake (acting as an emergency brake) should the trailer become detached from the towing vehicle.
The following instructions must be followed in order for the braking system to operate effectively:
- The release cable MUST NOT be wound around the jockey wheel, as this would prevent the
emergency brake from working.
- The release cable MUST run as straight as possible, without being impeded at any point.
- The release cable must be long enough to allow turning, and it must not be stressed or impeded in
use, as this would trigger the parking brake while the vehicle is being towed.
IMPORTANT
Coupling
1. Drive the towing vehicle or move the trailer (after releasing the parking brake, if fitted) to the coupling position.
2. Put the trailer in the horizontal position using the guide wheel (jockey wheel).
3. Put the hitching ring above the towing vehicle hook, and then lower the adjustable draw bar (if fitted) or lower the front of the
trailer to secure the ring in the hook; the trailer must remain in the horizontal position after this adjustment. Make any
necessary height adjustments using the jockey wheel to enable coupling.
4. Once this has been done, raise the jockey wheel until it is lifted off the ground slightly and is not bearing any load.
5. Attach the release cable to the attachment point on the hitching point (see Figure: Release cable), then plug the electrical
cable controlling the lamps, indicators, etc. into the socket on the towing vehicle. Check that the lamps on both the vehicle
and the trailer operate correctly.
6. Lift up the jockey wheel completely and lock it in position, making sure that it is not impeding the brake rod or the release
cable. In the case of a retractable jockey wheel, make sure that the safety pin has been correctly put back in position.
7. Ensure that the parking brake (if fitted) is completely disengaged by pushing its handle down fully. If necessary, remove and
store the wheel chocks.
MGS_186_EN _17/07/2017 15:01 33532000201_6_1 Section_5 _Transporting and storing the generating set 51
5.6.3.3 Hitching a trailer equipped with a coupling head (ball)
5.6.3.3.1 Coupling
1. Drive the towing vehicle or move the trailer (after releasing the parking brake, if fitted) to the coupling position.
2. Open the coupling head. To do so, pull the coupling handle (see Figure: Coupling head example) in the direction of the arrow.
The coupling mechanism can remain open as long as the coupling head is not resting on the tow ball.
3. Put the trailer in the horizontal position using the guide roller (jockey wheel), and then mount the open coupling head on the
hitching joint by lowering the adjustable towbar, if fitted, or by lowering the front of trailer. This must remain in the horizontal
position after this adjustment.
If necessary, adjust the height using the jockey wheel. The coupling head will be engaged automatically, accompanied by a
clearly audible click; then lower the coupling handle. The coupling mechanism will then be engaged, and the coupling handle
cannot adopt a lower position (when manoeuvred by hand).
4. Once this has been done, raise the jockey wheel until it is lifted off the ground slightly and is not bearing any load.
5. Attach the cable to the attachment point on the hitching plate (see Figure: Release cable), then plug the electrical cable
controlling the lamps, indicators, etc. into the socket on the towing vehicle. Check that the lights on both the vehicle and the
trailer operate correctly.
6. Raise the jockey wheel completely and lock it in position, making sure that it is not impeding the brake rod or the release
cable. In the case of a retractable jockey wheel, make sure that the safety pin has been put back in place correctly.
7. Ensure that the parking brake (if fitted) is completely disengaged by pushing its handle down fully. If necessary, remove and
store the wheel chocks.
52 Section 5 Transporting and storing the generating set 33532000201_6_1 MGS_186_EN _17/07/2017 15:01
5.6.3.3.2 Wear indicator (on certain models)
The coupling head has a wear indicator (see Figure: Wear indicator) that tells you whether the wear limit of the towing vehicle's tow
ball or that of the towed vehicle's coupling has been reached.
To use this indicator, couple the trailer and drive the towing vehicle approximately 500 m, so that the coupling head is positioned.
When you have done this, check the wear as indicated below.
green
red
In these conditions, the coupling head may release the tow ball, and the trailer becomes detached from the
towing vehicle. Therefore, the coupling head and tow ball must be checked prior to each use. All defective
parts must be replaced.
IMPORTANT
5.6.3.4 Operation
"On-site" trailer
These trailers are not fitted with a main brake, and so cannot be braked in motion; the tyres allow
for a maximum speed of 27 km/h. It is therefore absolutely prohibited to exceed this speed.
Nor are these trailers fitted with signalling lights. On-road use is prohibited.
"On-road" trailer
Special attention must be paid to the tightening of the wheels on new vehicles and after each
removal/replacement.
In the first few miles' driving, heating of the brake hubs and drums will actually loosen the lug nuts. It is
therefore essential that the lug nuts be checked every 6 miles (10 kilometres) until no further loosening is
noted.
IMPORTANT
The lug nuts should nonetheless be checked prior to each use of the trailer.
Should the trailer be at a right angle with the vehicle in reverse, never continue reversing.
The way you drive and your speed must be suited to the condition of the land, roads and paths and how the trailer handles.
Check the brakes at a speed below 30 km/h.
Driving at high speed causes the tyres to heat up; it is thus important to stop from time to time and check them. Excessive heating
may result in a blow-out and therefore cause a serious accident. For reversing manoeuvres, remember to lock the inertia brake.
5.6.3.5 Uncoupling
1. Set the parking brake (if fitted), and immobilise the trailer by chocking the wheels.
2. Using the jockey wheel, unlock the coupling and raise the drawbar to release the hitch from the towing vehicle. The jockey
wheel retraction mechanism (if fitted) must lock automatically before the jockey wheel touches the ground. When you are
sure that the mechanism is locked and that the wheel is bearing the load, the trailer can be uncoupled from the vehicle.
3. Disconnect the electrical cable plug controlling the lights, indicators, etc. from the socket on the towing vehicle.
4. Remove the release cable from the hitching plate.
MGS_186_EN _17/07/2017 15:01 33532000201_6_1 Section_5 _Transporting and storing the generating set 53
5.6.4 Technical information
Available drawbars:
RRTA
M125 750 kg
RRTF
RCTD
750 kg RRTA
RRTF
M126
1300 kg RRFTA
750 kg RTTA
M127
1600 kg RRFTA
(1) : Available drawbars: DIN40 ring / 68x42 ring / 76x42 ring / 50 mm ball.
54 Section 5 Transporting and storing the generating set 33532000201_6_1 MGS_186_EN _17/07/2017 15:01
5.6.4.2 Wheels and tyres
Characteristics of the threaded fasteners used to secure the generating set to the trailer:
- Recommended threaded fasteners: M16 class 8.8 minimum
- Self-locking nuts
- Recommended tightening torque (dry fit):
232 N.m for M16 class 8.8 screws
262 N.m for M16 class 9.8 screws
341 N.m for M16 class 10.9 screws
Keyed slot
MGS_186_EN _17/07/2017 15:01 33532000201_6_1 Section_5 _Transporting and storing the generating set 55
5.6.4.5 Maintenance schedule
When commissioning
Operations Frequency Every 6 months Every year
and before towing
General condition of the
vehicle
Tyre pressure
Tighten the wheel nuts
Efficiency of the automatic
brake
Efficiency of the parking
Check brake
Braking adjustment and
distribution across all wheels
Wear on brake linings and
drums
No play in the hubs
Play in the clamping tube
Play in the ball socket or ring
Braking control hinges and
Lubricate joints
Stands and jockey wheel rod
Lubricate or grease the moving parts on the coupling device (see lubrication points examples in the Figure: Trailer lubrication/greasing
points
Recommended lubricant: general purpose grease compliant with DIN 51825 KTA 3KA.
56 Section 5 Transporting and storing the generating set 33532000201_6_1 MGS_186_EN _17/07/2017 15:01
5.6.4.6
33532000201_6_1
Drum temperature abnormally high Incorrect brake adjustment Make adjustments*
Jaws, springs, drums, brake cable or linkage deteriorated Replace the damaged parts*
Damage to plunger or guide rings Replace the faulty parts and grease*
When starting, the trailer holds back Plunger corrosion Remove the corrosion and lubricate with grease
the towing vehicle Linkage damaged or incorrectly set Replace the damaged parts and make adjustments*
Faulty shock absorber Replace the shock absorber*
Play in the coupling head Head worn (see wear indicator) or ball worn Replace the head or the ball*
57
6 Installation
The generating set's installation location will be determined according to the application. There are no specific rules which govern the
choice of location, but the following elements are deciding factors:
- proximity to the electrical distribution panel;
- disturbances caused by noise;
- fuel supply;
- burnt gas evacuation;
- the nature of the ground.
The choice of location will therefore be the result of a carefully considered compromise!
The installation area should be flat enough for the frame to rest level on it and strong enough so that the generating set does not sink
down (on a slab, for example).
Furthermore, an operating generating set generates a certain amount of vibratory energy. This vibratory energy makes its way to the
ground via the frame. Installed on resilient mounts, our generating sets do not require a special support. However, the surface on
which the generating sets rest must be:
- strong enough to support the loading;
- detached from the rest of the construction;
- level;
- slab smoothed when poured;
- slab without separate screed.
If there is a risk of vibration transmission, the generating set can be mounted on a floating slab, insulated if necessary by a resilient
material. This solution is mainly used for very powerful generating sets.
Some generating sets are equipped with transport rollers (red in colour), facilitating their handling and
transport: the transport rollers must be removed prior to final installation of the generating sets concerned.
It is prohibited to rest the containerised generating sets on their ISO corners. A recess should be made for
IMPORTANT the ISO corners in the concrete slab.
CORRECT INSTALLATION
INCORRECT INSTALLATION
INCORRECT INSTALLATION
The regulations concerning fuel are unique to each country. Refer to the regulations in force in the country concerned.
Example of current regulations in France:
Decree of 10/08/982.
Decree of 19/11/01 – Article EL73.
- Daily fuel tank
The maximum capacity of the Daily Fuel Tank (DT) in the generating set room is 500 L for an Establishment Receiving
the Public (ERP).
Place the DT in a separate room if the volume is greater than 500 L.
- Use a retention container with a capacity greater than the capacity of the DT.
- Fuel pipe:
If the pipe is under load and underground: double skin.
Use a safety valve between the main tank and the DT.
Use a safety valve between the DT and the engine.
It is prohibited to use hoses in the ERP.
Regulations concerning the installation of an underground fuel tank are unique to each country. Refer to the current regulations in the
country concerned.
Example of an underground fuel tank installation according to the current regulations in France:
Decree of 22/06/19984 articles 9 and 11.
10 metres EMERGENCY
EXIT
PROPERTY
PROPERTY
UNDERGROUND
FUEL OR GAS
STORAGE TANK
TRANSFER
PUBLIC ROAD
2 Decree of 10 August 1998 modifying the decree of 25 July 1997 relating to general advice applicable to installations classified for
the protection of the environment subject to the declaration under section no.2910 (Combustion).
3 Decree of 19 November 2001 concerning the approval of conditions complementing and modifying the safety regulations against
the risk of fire and panic in establishments receiving the public. Article EL 7 concerning the installation of generating sets.
4 Decree of 22/06/1998 relating to underground tanks storing flammable liquids and their related equipment.
Since the fuel is classed as a "dangerous product", certain regulations for storage and distribution must be followed. It is also
necessary to consult current laws when carrying out the installation.
Do not use galvanised receptacles or brass coated receptacles for storing fuel.
IMPORTANT
RM 6 7
21 REC REM
1
ASM
24
8 9 3 11 12 13 11 4 5
ASM
P c
25 14 15
10
27 19 2
VB
23
20
26
17
16
1 - Daily service tank V1 10 - Non-return valve 19 - Filler
18 2 - Retention tank V2>V1 11 - 3-way valve 20 - Dipstick
22 3 - Electro-pump 12 - Filter 21 - Tank vent
4 - Manual pump 13 - Meter 22 - Earth plate
5 - DT leak detection 14 - Shut-off valve 23 - Safety valve
6 - DT dipstick 15 - Engine isolation valve 24 - Safety valve casing
7 - DT vent 16 - Single or double wall tank 25 - Shut-off valve casing
8 - Isolation valve 17 - Filling limiter 26 - Tracking
9 - Filter 18 - Foot valve with filter 27 - Leak detection (if double wall tank)
Use a retention container capable of collecting leaks, with a capacity which is at least equal to 110% of the total volume of fluid
present in the generating set (fuel, oil and coolant).
Analyse any noise pollution that the equipment may cause in order not to disturb those living close by.
Be aware of the regulations in force, in order not to be vulnerable to future legal action.
The sound level of the set and reverberation effects on buildings must be taken into account.
Figure 36: Examples of an increase in sound level caused by reverberations and sound directivity
For contractual reasons, certain logistics or technical equipment are either not delivered, delivered separately or delivered uninstalled.
Such items may include exhaust (protection from hot parts, spark arrestor, exhaust extension or outlet), cooling, and ventilation or
air-conditioning elements, as well as electrical elements such as cabinets. Before commissioning the generating set, install these
elements so as to ensure that the final product is compliant with the applicable regulations (e.g.: CE compliance). Call upon a
professional installer, if needed.
Generating sets are not equipped with devices that protect against voltage surges from atmospheric discharges or due to handling
operations.
The company disclaims all liability for any accidents caused by these phenomena.
However, it is possible to install surge protectors considering that this assembly does not provide complete protection.
6.2.1 Introduction
Note: failure to respect the main principles exposes the entire installation to damage and abnormal wear. The procedure described
lists the main requirements for installing a "standard" generating set composed of a heat engine, a generator and an electrical panel.
These requirements must be considered to be the general principles. For any special applications and if in doubt, our technical
services will advise you and assess your specific installation conditions. Moreover, the current regulations, requirements and laws
relating to installation locations should be respected.
FUEL STORAGE
AIR INLET
ELECTRICAL CABLES
The fire resistance rating must conform to the current legislation appropriate to the type of building.
IMPORTANT
The size and layout of the room are determined according to two requirements:
- Fixed requirements
These are the dimensions of the equipment installed and its peripherals, namely: daily fuel feed tank, electrical cabinet, silencer,
batteries, etc.
- Variable requirements
These are the dimensions which must be left around each
piece of equipment to allow for any maintenance and
dismantling operations.
A space of about 1 metre around the generating set is
considered the minimum required for carrying out problem-
free maintenance. This will leave enough space to check that
the doors of the covered generating sets open fully, that
equipment can be accessed for maintenance and that full
removal of the generating set can be carried out.
Access
Ensure that there is an access door which allows the generating set and its accessories to pass through, preferably along the axis of
the floor plate of the generating set.
Ventilation
- Ensure the presence of fresh air inlets and hot air outlets which are suited to the conditions of use and the cooling system.
- Define appropriately sized openings, in accordance with the following elements:
the generating set power;
the atmospheric conditions;
the cooling system;
the soundproofing method (if necessary).
- Ensure that the air is swept in the following direction: Alternator Engine Radiator.
- Ensure that the air inlets and outlets are as direct as possible.
- Connect the cooling system to a sheath or outlet cover so that it is sealed in order to prevent any hot air from being
recirculated.
- Ensure that the air inlets and outlets are never located near to each other.
It is preferable to release the vapour from the crankcase outside the generating set room in order to prevent a
deposit from developing on the radiator which may cause the radiator to clog and affect its cooling ability.
Ensure that the crankcase vapours are recovered in order to preserve the environment.
IMPORTANT
Note: a heat engine generates a certain amount of heat, which must be evacuated outside the room to ensure that the generating set
works properly. The heat released by the generating set originates from different sources:
- cylinder cooling;
- radiation from the engine unit and exhaust duct;
- alternator cooling.
Insufficient ventilation would cause the ambient temperature to increase which, at the very least, would cause loss of engine power
and potentially cause the generating set to shut down.
The lifting system must, in general, form an integral part of the construction. It is composed of a mobile winch which moves along an
H- or I-shaped sealed steel rail in the walls and ceiling. This system is generally positioned above and in the longitudinal axis of the
generating set, directed towards the exit.
Regulations concerning sound emissions are unique to each country. Refer to the regulations in force in the country concerned.
Example of current regulations in France:
Decree of 25/07/97, section 29105 - 8.1
- Noise emissions produced by the installation must not, to begin with, have an emergence greater than the permitted values
specified in the following table in the statutory emergence zones:
Ambient noise level in the statutory Permitted emergence for the period from Permitted emergence for the period from
emergence zones (including noise from 7:00 am to 10:00 pm except for Sundays 10:00 pm to 7:00 am as well as on
the establishment) and bank holidays Sundays and bank holidays
Sound trap
Silencer
Sound trap
Soundproofed doors
5 Decree of 25/07/97 relating to general advice applicable to installations classified for the protection of the environment subject to
the declaration under section no.2910 Combustion.
Regulations concerning exhaust emissions are unique to each country. Refer to the regulations in force in the country concerned.
Example of current regulations in France:
Engine with a thermal power consumption greater than 2,000 kW.
Decree of 25/07/97 art. 6.2.6 - 2 modified by the decree of 15/08/00.
Pollutants
Production
Applicability Production Production Production Production
Emergency
1 - Exhaust pipe
2 - Elbows
3 - Compensator
4 - Condensation bleed
5 - Bulkhead crossing - roof outlet
6 - Exhaust outlet
7 - Suspension line
8 - Needle frame
9 - Column base
10 - Silencer suspension
11 - Thermal insulation
12 - Silencer
Note 1: It should be noted that the more complicated a circuit, the more it causes drops in pressure and consequently, its diameter
will be large and heavy and its supports and silencers expensive.
Note 2: Exhaust circuit components marked in Figure: Example of a burnt gas exhaust circuit, are explained in the following
paragraphs.
No. 2: Elbows
Elbows must have a minimum curve radius equal to 2 times the
diameter of the pipe, if possible in a single part. If the elbow is
made of welded steel, check that it includes at least 3 sectors for Figure 42: Examples of pipes and elbows
90° elbows.
Silencer
No. 12: Silencer
Silencers reduce noise by absorbing or dephasing the sound wave. The exhaust should be suspended correctly; under no
circumstances should the supports be reused on the generating set (except for original fittings).
Absorption silencer
Gas moves through a soundproofed duct composed of a highly
absorbent material protected by a perforated panel.
"Adapted" silencer
The "adapted" silencer is fitted directly onto the generating set or
in the cover. It is an absorption silencer.
Regulations concerning the chimney height are unique to each country. Refer to the regulations in force in the country concerned.
Example of current regulations in France:
Minimum ejection speed: 25 m/s
- Emergency operation of the main electrical supply with a building present within a radius of 15 metres of the installation:
Decree of 25/07/97 section 2910 - 6.2.2.E
The height of the exhaust chimney should exceed the height of the buildings located less than 15 metres around
the installation by 3 metres, whilst being less than 10 metres.
For d < 15 m => Hchim = Hobst + 3
Telescoping chimney
Chimney flue
Container
Trap
Receptacle
for condensate
Drain valve
The systems described below evacuate and channel the heat produced by the engine cooling circuit.
Ventilated radiator
The engine cooling circuit is connected to a tubular ribbed radiator at the end of the frame. This radiator is cooled by the fan controlled
directly by the engine.
In all cases, the air is blown in the Fan Radiator direction.
Note: an expansion vessel can compensate for variations in the volume of coolant fluid according to the temperature.
Air cooler
The engine cooling circuit is connected to an air cooler located inside or outside the room.
When located in the room, it operates in the same way as a ventilated radiator. The fan or fans are either coupled to the engine or
driven by one or more electric motors.
If the air cooler is positioned outside, on the roof or in another room, the coolant pipes are extended, meaning that ventilation of the
room is separate from the cooling.
In these installations the degassing conditions should be considered even more carefully than for a radiator.
In all cases, the air cooler is cooled by the fan(s).
Note: if cooling using a radiator or air cooler in the room, the increase in temperature due to heat radiation for the sizing of the
installation should always be taken into account.
Install the equipment, taking into account the prevailing winds: position the air inlets away from the wind to ensure there are no
difficulties in adverse weather conditions (entry of air, snow, sand, etc.).
Respect a minimum distance of 2 metres between the container air inlets and outlets and any ventilation obstacles.
Air inlet
2 m,
2 m, min.
min.
Air
discharge
Air inlet
Make sure that the air inlets are oriented away from the prevailing winds in order to avoid any inconvenience during difficult climatic
conditions (entry of air, snow, sand,...).
Arrange the equipment so that the exhaust fumes will not bother the control panel operator.
1. It is imperative to remove the exhaust outlet cover plate(s) (used for transport).
2. Install the extension ,supplied with the generating set, in place of the cover plate(s) .
IMPORTANT 3. It is imperative to maintain a clearance of 3mm between the extension and the roof of the canopy.
≈ 3 mm
Figure 58: Removing the cover plate Figure 59: Installing the extension
When using a tall chimney, preferably use a self-stabilising chimney installed next to the container.
The general checks referred to in this section are performed in conjunction with the generating set's commissioning operations. They
must be adapted or complemented according to the actual commissioning conditions.
- The generating set must meet the needs of the installation in terms of its power requirements and configuration.
- The installation must have been performed in compliance with recognised trade practices by a qualified person: the
installation must be clean, correctly maintained and regularly checked throughout the generating set's service life.
- Carefully read the operating and servicing manuals provided, note the maintenance to be performed and the associated
deadlines. Throughout the generating set's service life, regularly check that the deadlines are respected.
After all connections have been made, ensure that the cable passageways on the installation have been
properly sealed (notably concerning enclosed generating sets).
IMPORTANT
Head disconnect
point open
Grid
Generating set
General information
Low voltage electrical installations are subject to the regulations set out in standard NFC 15.100 (France) or the standards in the
countries concerned based on international standard IEC 60364. Cable routing must comply with NFC 15.100, paragraph 528
“Electromagnetic disturbances” or lEC 60364-4-44 “Protection against voltage disturbances and electromagnetic disturbances”.
They must also adhere to the regulations in the NFC 15.401 application guide (France) or to the regulations and standards in the
relevant country.
Power cables
- Power cables should preferably be installed in ducts or on a cable tray for this purpose.
- Determine the cable cross-section and number of cables according to the cable type and the current standards to be
observed in the country of installation. The choice of conductors must comply with international standard IEC 30364-5-52.
Note: the power cables may be unipolar or multipolar according to the power of the generating set.
Any change to the setting on the general residual current device could pose a risk to personal safety. The
user will be held liable - any changes must only be made by trained, qualified engineers.
IMPORTANT
Note: when the generating set is disconnected from an installation after use, the general residual current device must be restored to
factory settings by a qualified engineer who can then check this.
To ensure that the device providing protection against electric shocks is effective, connect the generating set to the earth. To do
this, use a copper wire with a minimum cross-section of 25 mm2 for a stripped cable and 16 mm2 for an insulated cable, connected
to the generating set earth socket and a galvanised steel earthing rod embedded vertically into the ground.
Ensure that the resistance value of this earthing rod complies with the values indicated in the table below (use the highest
differential setting from the installation as a guideline).
UI
The resistance value is calculated in the following way: R
I n
Maximum resistance value of the earth socket R (Ω) according to the differential unit operational
current (operation time should not be longer than 1 second)
Earth R Earth R
I Δn
(Ω) (Ω)
differential
Ul: 50 V Ul: 25 V
≤ 30 mA 500 > 500
100 mA 500 250
300 mA 167 83
500 mA 100 50
1A 50 25
3A 17 8
5A 10 5
10A 5 2.5
The Ul value: 25 V is required for site installations, and livestock buildings, etc
For a default voltage of 25 V and a default current of 30 mA, this rod must be of a minimum length of: see table below
Length of
Nature of ground rod in
metres
Thick arable land,
1
moist compact ballast
Lean arable land,
1
Gravel, coarse ballast
To obtain an equivalent length, you can use several earthing rods
Bare stony soils, dry sand,
3.6 connected in parallel and set apart by at least their length.
impermeable rock
Example: 4 interconnected 1 metre rods separated by 1 metre.
Note: for the United States (National Electrical Code reference NFPA-70).
The generating set must be earthed. To do this, use a copper wire with a minimum cross-section of 13.3 mm² (or AWG 6, at most)
connected to the generating set earth socket and a galvanised steel earthing rod embedded vertically and fully into the ground.
This earthing rod embedded fully in the ground must have a minimum length of 2.5 m.
The Earthing system, or SLT (formerly Neutral system) of the electrical installation defines the situation of the generating set neutral
in relation to earth and the grounds of the electrical installation at the user end.
The purpose of the earthing systems is to protect personnel and equipment by managing the risks posed by insulation defects. For
safety reasons, any live conducting part of a facility must be insulated from the earth. This insulation may be achieved by distance,
or by using insulating materials. But with time, insulation may deteriorate (due to vibrations, mechanical impacts, dust, etc.), and
therefore generate an earth with dangerous potential. This defect poses risks for personnel and property, but also continuity of service.
Earthing systems are codified by two letters that define the connections:
- The first letter defines the neutral connection:
I Insulated or earthed via an impedance device
T Connected to earth
- The second letter defines the grounding situation of the electrical facility:
T Connected to earth
Connected to
N
neutral
Number of
Speed Detection Note
conductors
C 3 poles
Triggered by overcurrent protection
TN No measurement of residual current
upon 1st fault
S 4 poles
R R
Ph 1 Ph 1
Ph 2 Ph 2
id
Ph 3 Ph 3
N N
PE PE
id
R
Neutral connected Ground connected
R
to earth to earth
T T
id
Neutral earth Ground earth
The alternator neutral is earthed, and the grounds of the user equipment have their own earth connection.
This earthing system is the most frequent in the private sector in France.
In the TT system, automatic power cut-off via a Residual Current Device (RCD) is obligatory at the upstream part of the facility, to
ensure that personnel are protected (with a maximum 30 mA device on outlet circuits).
In the TN system, the alternator neutral is earthed and the user grounds are connected to the main protective conductor (PE), itself
connected to the earth socket.
Ph 1 Ph 1
Ph 2 Ph 2
Ph 3 Ph 3
N N
PE PE
id
Ground to neutral SeparateSeparate
N Neutral conductor
protective conductor
id
id
Neutral connected
to earth
T
Neutral earth
In the TN-S system, the power supply is automatically cut by the opening of the overcurrent protection circuit breaker protecting the
faulty circuit.
TN-S is obligatory for networks with aluminium conductors which have a cross-section ≤ 16 mm2.
Ph 1
Ph 2
Ph 3
N
PE
Ground connected
Neutral insulated to earth
I T
Z CPI
Ph 1 Ph 1
id
Ph 2 Ph 2
Ph 3 id Ph 3
N N
PE PE
id
id
id
id id
Z CPI Z CPI
id
In the IT earthing system, the alternator's neutral is earthed via an impedance device (Z) greater than
1000 Ohms, or insulated (Z=∞). The installation's grounds are earthed (see Figure: Neutral IT system). It should be noted that an
IMD (Insulation Monitoring Device) is connected in parallel to this impedance device Z to monitor the circuit's insulation at all times.
- First fault: the current flowing through the metal frame passes through the neutral impedance device Z, which means a very
low current (or practically zero if neutral is insulated), so the contact voltage is not dangerous. That is why hospitals, concert
halls, etc. use this system to avoid outages in the case of a first fault. The IMD (Insulation Monitoring Device) detects this
leak and reports it via an indicator light and/or an alarm.
- Second fault: both conductors concerned by insulation faults are interconnected, leading to a short-circuit. The power supply
is automatically cut by the opening of the over-current protection circuit breaker, as in the TN system. It should be noted that
the IT neutral system must not be used if you do not have a technician on call 24/7.
For the IT neutral system, in the case of a 20 kV/400V step-down transformer, it is necessary to provide overvoltage protection for
the 400V network. This protection must be mounted between earth and the neutral point, if available, or a phase if not available.
For an LV generating set with an IT system, this protection is not necessary, as the voltage cannot be over 500V.
The network's insulation voltage must be the value of the phase-phase voltage.
General information
Installations having a voltage range between 1 kV and 50 kV are referred to as “high voltage electrical installations” (HVA). These
high voltage electrical installations are subject to the regulations set out in standard NFC 13.100 and more particularly NFC 13.200
(France, voltage range from 1 kV to 33 kV) or the standards in the countries concerned based on international standard IEC 62271.
Cable routing must comply with NFC 13.200, paragraph 451 "Electromagnetic disturbances" or with IEC 62271-1 and IEC 62271-
200.
Equipment
The choice of the required equipment shall be made based on the following criteria:
Example:
The operating voltage must be below the rated voltage.
Voltage - Operating voltage: 20kV
This voltage shall define the isolation voltage.
- Rated voltage: 24kV
Power cables
The high voltage cables must have metal shielding on the insulation or on the assembly of conductor cables, to ensure:
- earthing along the entire circuit,
- dissipation of capacitive currents,
- dissipation of phase-earth fault currents.
The cross-section shall be selected following the study of overcurrents and protections implemented.
Battery cables
- Install the battery or batteries in close proximity to the electric starter motor. The cables will be connected directly from the
battery terminals to the starter motor terminals (§ "Connecting/disconnecting the battery").
- Check that the polarities of the battery and starter motor correspond. (an inversion could cause severe damage to the
electrical equipment).
- The minimum cross-section of the cables is 70 mm2. This cross-section varies according to the power of the starter motor
but also the distance between the batteries and the generating set (voltage drops on the line).
Protection of persons
A set of protection and intervention equipment in good condition must be made available to operators in each room containing HVA
equipment (gloves, rescue pole, insulated stool, etc.).
HOMOPOLAR
GÉNÉRATEUR
INSTALLATION HOMOPOLAIRE
GENERATOR
Figure 64: Power supply diagram including external sources which may be coupled to the HVA grid
In all cases, the overload and short-circuit currents specific to the installation must be calculated. The addition
IMPORTANT or the removal of a generator or receiver shall require verification of the resistance of the various elements of
the installation to overcurrents.
The fluids used by the generating sets, such as oils, fuels and coolants, are
dangerous products. Do not ingest, avoid all extended or repeated contact
with the skin (gloves are recommended), and keep out of the reach of
DANGER children.
All specifications (product features) are given in the engine and alternator maintenance manuals attached to this manual.
In addition to these documents, it is strongly recommended that the fuels, lubricants and coolants mentioned in the “Specifications”
chapter, be used.
Good fuel quality is vital for good engine performance. This applies both to technical performance, such as longevity, power, and fuel
consumption as well as the ability to comply with the rules set out by the authorities regarding emissions. Only fuels complying with
current legal requirements and national and international standards must be used Consult the local fuel distributor to find out about
the characteristics of the diesel which is available in the region.
Examples of standards and requirements :
European standard (CEN) for automotive fuel - diesel engine fuels - requirements and test
EN 590
methods
American Society for Testing and Materials : basic requirement for the United States and
ASTM D 975 1-D and 2-D
Canada
JIS KK 2204 Japanese Industrial Standards
Emissions compliance
Certification measures confirming that the legal emissions limit values are adhered to shall be carried out using certified fuel
conforming to the requirements and standards referred to above.
In low outside temperatures diesel fuel may become insufficiently fluid due to build up of paraffin deposits. Also, in order to avoid any
malfunctions (blocked filters for example), procure, in winter, diesel fuel which is sufficiently fluid in cold temperatures.
Requirements to be met for different geographical regions and for different seasons (winter/summer) are specified in national
standards and/or regulations. Petroleum companies must always take care to supply fuels whose cold flow properties are correct for
any time of year. Generally, diesel contains additives so it can be used in low temperatures in the region where it is sold.
Any fuel additives must comply with the engine manufacturers recommendations and be of sufficient lubricity to suit the injection
systems. It is preferable to use fuels ready mixed with additives in the refinery than those which are mixed together in a storage tank.
Notes:
- 0.5% sulphur = 5000 ppm and 1% sulphur = 10000 ppm.
- EATS = Exhaust After Treatment System.
- HFRR (High Frequency Reciprocating Rig) : testing method used to evaluate the lubricating properties of diesel fuels.
- DFO: Domestic fuel oil
DFO : We recommend improving storage conditions by using fuel which has been pretreated in the refinery in order to stabilise the
fuel (avoid oxidation, bacterial growth and corrosion). We recommend adding a water separator between the main fuel storage tank
and the day tank.
Fuels containing biodiesel : We recommend improving storage conditions by using fuel which has been pretreated in the refinery in
order to stabilise the fuel (avoid oxidation, bacterial growth and corrosion)
The military version of kerosene based fuel with additives (Nato F-63 or XF-63) is the type of fuel most adapted
to our generating sets, however it still retains the negative impacts of points 3 - 6.
Use of NATO F-63 or XF-63 fuel is a replacement choice whereby the user of the genset must assume any
impact on service life of the engine and performance of the generating set.
Selecting the right oil based on its use is essential for correct engine operation. Besides the lubrication function, an oil must also:
- cool certain parts;
- protect metal parts against corrosion;
- improve sealing, in particular between pistons, piston rings and cylinders;
- remove impurities (to the filter).
It is recommendable to use a premium lubricant for diesel engines. The table below lists the oils recommended for each engine
manufacturer.
ENGINE OIL
BRAND TYPE BRAND TYPE
KD27V12
K135 KD36V16 KOHLER. GENLUB EVOLUTION 15W40
KD45V20
GENLUB EVOLUTION 15W40 (*)
(*) Engine water preheating is required => system fitted as
KOHLER.
standard for ESP/DCP/LTP/PRP applications.
KD series KD62V12
K175 KD83V16 KOHLER.
Note: For applications without engine water preheating, use
KD103V20
viscosity 10W40 or 5W40.
(For example: Total Rubia works 2000 viscosity 10W40 / Shell
Rotella T6 viscosity 5W40)
LOMBARDINI
All KOHLER. 5W40 OIL
KOHLER.
JOHN DEERE All KOHLER. GENLUB EVOLUTION 15W40
Note: To use an oil other than the KOHLER brand, it is necessary to obtain the approval of the KOHLER engineering and design
office or the after-sales department.
Use:
“Power generation” Particularly intended for all-season lubrication of generating set engines, but also all stationary
engines.
All engines compliant More generally, it is dedicated to all engines having to operate for long periods of time under
with standards
TIER 1, TIER 2 and TIER full load or repeated phases of acceleration and idle.
3 It is specially recommended for engines with the latest technology and rated to the EURO
Stage IIIa or US EPA TIER 3 emission standards.
Performance:
ACEA : E7 (E5)
API : CI-4 / CH-4 / CF
Classifications JASO : Level DH-1
The KOHLER GENLUB EVOLUTION 15W-40 formulation has been approved by engine
manufacturers who fit out the generating sets, such as:
MTU (Category 2)
Compliant with VOLVO (VDS-3)
specifications KOHLER KD series
Advantages:
Total safety Excellent thermal stability ensuring good lubrication of hot engine parts, particularly during
intensive and continuous operation.
Extended oil change Reinforced dispersion, detergent and anti-wear capability allowing the engine oil to resist
intervals
attacks between long oil change intervals: dust, soot, water, diesel fuel, and combustion acid.
Simplified engine For the lubrication of all types of older and newer generation engines, regardless of brand and
lubrication type.
Specifications:
Use:
“Power generation” Recommended for petrol engines (multi-valve and turbocharged engines fitted with or without
a catalytic converter) and diesel engines with or without a turbocharger.
Direct injection Specially recommended to satisfy the requirements of direct injection diesel engines.
Can be used under the most severe operating conditions.
The most intensive
applications
All seasons
Performance:
Advantages:
High performance Excellent engine protection, particularly against distribution wear and tear.
Exceptional thermal and corrosion stability preventing deterioration even under very intensive
Increased use.
engine life
KOHLER 5W-40 has been designed to satisfy the manufacturer’s requirements in terms of
Extended oil extended oil change intervals.
change intervals
Specifications:
The engine's internal cooling system allows the engine to operate at a precise temperature.
The table below lists the coolants recommended for each engine manufacturer.
ENGINE
MITSUBISHI LLC
MITSUBISHI All
KOHLER GENCOOL PC -26
pH pH 7.5 to 8.5
Alkalinity reserve ML ≥ 10
- Check the position of the generating set (stability, mounting, available space, ventilation, exhaust, etc.). See the chapter
entitled "Installation".
- Check that the plugs, blanking covers and protective adhesive strips have been removed.
- Ensure that the desiccant bags have been removed from the electrical elements (cabinet or control console, alternator, etc.).
- Check the electrical connections (See the chapter entitled "Electrically connecting a generating set"):
earthing;
electrical control connections;
electrical power connections;
starter battery charging system (rating and voltage) if so equipped.
- Check that the residual current devices are operating correctly.
- Check the tension of the drive belt(s).
- Check the alternator's insulation.
- Check the starter battery or batteries (connecting and charge). See the paragraph entitled "Starter batteries".
- Check the starter battery charging system (if so equipped).
- Check the levels See the engine's maintenance manual:
coolant;
oil;
fuel.
- Check that the additional equipment is in good condition and operational (notably the air filter).
- Open the oil filler tap (if so equipped).
- Open the fuel tap (if so equipped).
- Select the fuel supply method (tank, day service tank, etc., as the case may be).
- Bleed the air from the fuel system and prime the system as required, taking all necessary precautions and in full respect of
the safety instructions (See engine maintenance manual).
For generating sets equipped with a MTU 2000Gx5 / MTU 2000Gx6 type engine and a Beaward
radiator: check that the shell is centred in relation to the radiator.
For generating sets equipped with MTU 4000 series engines: the engine flywheel blocking device must be removed (crankshaft
protection during transport) before the generating set is started for the first time.
For generating sets equipped with Lombardini / Kohler engines: These engines must be run in. Do not exceed 70% of the
rated power for the first 50 hours of operation.
Some generating sets are fitted with variable temperature controllers and regulators
which control the speed of rotation of the fans according to the level of cooling
required for the correct operation of the generating set.
To ensure this system operates correctly, certain adjustments and checks must be
made before starting up the generating sets. The procedure below describes these
operations and applies to Schneider systems fitted with an "ALTIVAR 21" variable
controller and a "REG48PUN1JLU" regulator.
All the operations are carried out while the generating set is running
IMPORTANT
Check the values shown in the temperature regulator value settings table
For generating sets operating occasionally, throughout the service life of the unit, regularly check, or before each start-up, the overall
cleanliness, general condition of the installation and the generating set, and particularly the following points:
- Check for elements that may block the air inlets and outlets, radiators and fans (dirt and debris, ice, branches, etc.).
- Check the fluid levels - see the engine's maintenance manual:
coolant;
oil;
fuel.
- Open the oil filler tap (if so equipped).
- Open the fuel tap (if so equipped).
- Select the fuel supply method (tank, day service tank, etc., as the case may be).
- Check the starter battery charging system (if so equipped).
- Check the starter battery or batteries (connecting and charge) - see the paragraph entitled "Starter batteries".
Some of our generating sets are equipped with an optional auxiliary preheating system. It can be activated automatically or manually,
depending on the configuration chosen.
7.6.2 Starting
The start-up procedure differs slightly according to the generating sets' configuration and their integration within the installation. For
generating sets equipped with a control unit, refer to the control unit's operating manual for information regarding the manual or
automatic start-up modes and the associated configurations. If in doubt, please contact your nearest agent.
Off-load tests
- Carry out the safety checks (emergency shutdown, oil pressure, coolant temperature, etc.).
- Check the mechanical parameters:
engine parameters (oil pressure, coolant temperature);
absence of abnormal vibrations;
absence of abnormal noises;
absence of leaks.
- Check the electrical parameters:
voltage, frequency, current;
rotating field.
On-load tests
- Check the mechanical parameters:
engine parameters (oil pressure, coolant temperature);
absence of abnormal vibrations;
absence of abnormal noises;
absence of leaks.
- Check the electrical parameters:
voltage, frequency, current;
rotating field.
When operating at no load or low load (< 30% of nominal power), the operating conditions are such that the engine cannot be used
at its optimum level. The main reasons for this are:
- A small volume of burnt fuel in the combustion chamber means that full combustion cannot be attained; the thermal energy
resulting from the combustion is not great enough for the engine's optimum operating temperature to be reached.
- Supercharged engines have lower compression ratios (low compression ratio without supercharging), which are required for
full load, and not suitable for good combustion at low load.
The combination of these factors leads to engine clogging and, in particular, the piston ring and valve clogging which results in:
- accelerated wear and glazing of the cylinder liners;
- reduced leak tightness of the mating faces, with valve rod movement sometimes becoming less efficient (sticking).
Consequently, using any supercharged engine at low load (< 30%) during tests or normal use can only have negative implications
for engine operation and service life. Maintenance will have to be stepped up in order to cope with the severe operating conditions.
Shortening draining intervals, among other things, will enable you to change the oil more frequently, which will tend to be choked with
unburnt particles and contaminated with fuel. A ballast resistance is generally added to reduce periods of low load operation and to
enable full load to be reached periodically, which is necessary to unclog the engine.
Finally, when operation is taking place under load, we recommend that you pay close attention to the oil venting system, especially
for engines whose sump air vent is located at the supercharger inlet (risk of oil or oil vapour uptake and engine racing).
On production generating sets (such as the CPU20 type or CPU40 type container or specific generating set), the upstream fuel filters,
mounted on the inside face of the side doors, can be replaced while the generating set is in operation. For these foreseen, yet
exceptional operations, all safety measures must be taken to prevent accidents, notably:
- Wear the necessary personal protective equipment,
- Prior to the operation, identify all potential hazards (rotating parts, hot parts, etc.),
- Locate the emergency stop and ensure that it can be easily activated at any time during the operation (by the operator or
by another person),
- Replace the filters one by one, shutting off the fuel supply progressively on each filter. Recover the fuel in a recipient provided
for this purpose.
Furthermore, while the generating set is in operation, the container may be under a slight positive or negative pressure (significant
suction or delivery of air by the cooling fans, depending on the configuration). This normal process may either cause the outward
opening side doors to open with slightly greater force when the generating set is in operation (take care when opening them, and only
when necessary), or cause doors to close unexpectedly and make them more difficult to open from the inside (in this case, use the
emergency stop button to shut down the generating set).
The shut-down procedure differs according to the generating sets' configuration and their integration within the installation.
In all cases:
- The emergency stop button to stop the generating set should be reserved for exceptional situations in which the safety of
persons is at stake.
- Progressively lower the load demanded to the generating set and allow it to idle (0% load) for ten or so minutes before
stopping it.
For generating sets equipped with control units, refer to the control unit's operating manual for information regarding the manual or
automatic shut-down modes and the associated configurations. If in doubt, please contact your nearest agent.
Become aware of the safety instructions prior to all operations. Ensure that all adjustments and repairs are carried out by personnel
who have received appropriate training. Our dealers are highly qualified and can answer all of your questions. They can also supply
you with spare parts and other services and they have qualified staff to carry out preventive and corrective maintenance on generating
sets and even ensure their complete overhaul.
The user should check that the installation is in good working condition at all times.
- Perform the maintenance operations outlined in the documentation supplied with the generating set.
- Perform regular checks and tests to ensure that the installation is operating correctly.
These regular servicing operations, checks and tests must be recorded in a test log containing the following information: interval,
nature of the inspection and/or test performed, date and time carried out, report of operations, and the name and signature of
technician.
The maintenance plans (periodic maintenance tables) are outlined in the respective documentation (service
manual) for the engines, alternators and for certain additional equipment. As a general rule, these plans make
a distinction between use under continuous operation and use under emergency operation. They also take
the consumables used into account, for example: the sulphur content of the diesel fuel or the grade of lubricant
oil.
The maintenance plan should be adapted based on the configuration of the installation, the generating
set and all the equipment.
IMPORTANT Preference should be given to the manufacturer's recommendations, and their servicing rules are to
be followed when performing the operations.
The operations below are to be performed in addition to the manufacturer's recommendations. If you
have any doubt, please contact one of our agents.
FREQUENCY (h)
Comments
LEVEL (1)
Commissioning
Calendar limit
10h / 1 x day
After 20h
OPERATIONS
1000h
500h
GENERATING SET
Load testing at min. 50% of rated power (ideally 80%) for 1 hour after
stabilisation of parameters (2) and associated checks 1 1m
(Reminder: Does not replace the manufacturer's recommendations)
Check for leaks 1 6m X X X
Visually inspect general condition 1 6m X X X
Check the clogging indicator on air filter(s) (if fitted) 1 6m X X X
Check the condition and connections of hoses and pressure lines 1 6m X X X
Clean the generating set 1 6m X
Clean the relays and contactors with low-pressure compressed air 3 6m X
Check the condition and connections of the electrical equipment 1 6m X X X
Check the condition of drive belts 2 1y X X X
Check and retighten fasteners 1 1y X X X
Test the differential relay (3) 3 1y X
CONTAINER
Check and bleed the various fuel filters on generating set(s), as required 2 6m X X X X
Replace the various fuel filters on the generating set(s) 2 1y X
Check the condition and cleanliness of the air inlet and outlet elements 2 6m X X X
Check the condition and cleanliness of the radiators 2 1y X
Check the condition and cleanliness of the sound traps 2 1y X
BATTERIES
Check the charging system and the charge status of the starter batteries,
3 6m X X
remote control
Service the batteries (starter and remote control, if equipped) 3 1y X
EXHAUST SYSTEM
Check the condition of the elements (mechanical condition and alteration of
2 1y X
materials)
Check that the various fasteners are tight (support, frame, clamping or
2 1y X
mufflers)
FREQUENCY (h)
Comments
LEVEL (1)
Commissioning
Calendar limit
10h / 1 x day
After 20h
OPERATIONS
1000h
500h
AIR COOLER
All of these factors lead to choking of the engine, in particular the piston rings and valves, which leads to:
- accelerated wear and glazing of the cylinder liners;
- loss of sealing of seats, and sometimes sticking of valve stems.
Consequently, operating any turbocharged engine at low load (< 30%) during tests or normal use can only have adverse
repercussions on an engine's operation and its service life. Maintenance intervals will have to be shortened to accompany harsh
operating conditions. Shortening draining intervals, among other things, will enable you to change the oil more frequently, which will
tend to be choked with unburnt particles and contaminated with fuel. A ballast resistor is generally added to limit low load phases and
obtain the periodic full loads necessary to unchoke the engine.
Finally, when operating under load, we advise vigilance with regard to the oil breather circuit, and more particularly to engines which
have the crankcase vent connected to the turbocharger inlet (risk of oil or oil vapour absorption and accelerated engine speed).
Tests on emergency supply generating sets (only concerns France, see NF E 37-312)
For emergency supply generating sets (GSS), the following tests must be performed:
- periodic checks on the oil, coolant and fuel levels, the engine heating device and the condition of the source used for start-
up (battery or compressed air), for example every two weeks;
- automatic starting test with a minimum load of 50% of the nominal power of the generating set when used or on a ballast
resistor, for example every 6 months. During this test, the fuel supply cut-off valve, reserved for emergency purposes, must
never be used when the generating set is in operation.
The sealing between the cover and the frame and between the frame and the retention tank is ensured by a gasket.
It is essential to replace the gasket if the cover has been removed.
IMPORTANT
Users must maintain the enclosures and base frames to ensure that the paintwork retains all its protective properties.
1. Open the doors of the generating set if necessary, then remove the panels and keep the bolts.
2. Clean the inside of the generating set: remove any plant debris, leaves and waste and check that the drainage holes are not
blocked.
3. Carefully screw the removable panels back on and close the generating set doors if necessary.
4. Wash the outside of the generating set using a cleaning agent (water with a mild detergent added, e.g. car shampoo).
5. Carefully rinse with clean fresh water to remove any trace of cleaning product at an operating pressure of less than 120 bar
(if using a high-pressure washer, maintain the washer nozzle at a distance of at least 20 to 30 cm from the surface to be
cleaned).
6. For generating sets equipped with a retention tank, perform the draining operation recovering the fluids and, when possible,
check the condition and operability of the retention tank's high level sensor.
7. Dry with a soft, absorbent cloth.
A cleaning foam may be used and wiped off using a soft, absorbent cloth. Stubborn stains may be removed using a suitable solvent
(white spirit or equivalent) and wiped off using a soft, absorbent cloth.
Curative treatment will be necessary to eliminate any major scratches. This treatment should be carried out by a trained professional.
IMPORTANT
M1xx enclosures
Drainage holes
Removable panel
M2xx enclosures
Removable panel
Drainage holes
Drainage holes
Removable panel
M4xx enclosures
IMPORTANT
Removable
panel
This chapter outlines the general rules for maintaining the lubricating, fuel and cooling circuits.
Taking into account the configuration of the installation, the generating set and the associated equipment,
adapt the proposed procedures.
Preference should be given to the manufacturer's recommendations, and their servicing rules are to be
followed when performing the operations.
IMPORTANT
The operations below are to be performed in addition to the manufacturer's recommendations. If you have
any doubt, please contact one of our agents.
Hot oil.
The oil may contain harmful combustive residues.
Danger of burning and poisoning!
DANGER - Wear protective clothes, gloves and masks.
- Avoid contact with the skin.
- Do not breathe the oil vapours.
In order to correctly compare the results, it is necessary to make sure of the representativeness of the samples by means of a suitable
sampling method.
When in severe conditions of use, analyses should be carried out more frequently, for example when:
- in extreme climatic conditions ;
- subject to repeated starts ;
- the engine is running for a long time on low load ;
- there is high sulphur content in the fuel (from 0.5 to 1.5% by weight).
Some signs that the oil is no longer carrying out its function may include:
- Unusually large deposits or precipitations on the inside of the engine and its components such as filters, centrifuges or
separators, in particular when compared with the previous analysis ;
- unusual discolouration of components.
As a precaution, also send a bottle containing a new oil sample which will serve as a reference point for the analysis of the used oil.
SAMPLING POINT:
Sampling is carried out at a representative point in the system, preferably just after the machine is shut down:
- always at the designated sampling point(s)
- failing this, via the dipstick well with a syringe and flexible hose ;
- as a last resort, directly from the sump drain point after draining the polluted fluid at the bottom of the sump.
SAMPLING METHOD:
This method can be used by adapting the periodic draining of the oil sump.
Figure 66: Examples of oil sump drain valves Figure 67: Oil drainage pump
a) Remove the filter using a suitable tool and dispose of the filter element.
b) Clean the sealing surface on the connecting part.
c) Check the sealing ring of the new filter and coat it with new oil
d) Screw the new oil filter on according to the manufacturers recommendations.
e) If applicable, replace the other filters in the same manner.
High pressure fuel in the fuel lines may cause serious injury.
Do not disconnect the fuel lines between the fuel pump and injectors.
Only drain the fuel system via the fuel filters.
Before carrying out any work make sure that the pressure in the fuel system has dropped.
DANGER
Additional fuel filters are fitted on some generating sets. In addition to the recommendations that appear in the maintenance manuals
for the engines (filters fitted by the engine manufacturers), the operations described in this paragraph must be performed.
A : FILTER
B: SEAL
C: WATER DRAIN D B
D: AIR BLEED VALVE
E : PRIMING PUMP E
F: WATER SENSOR A
B ISOLATION VALVES
D
B
A
A
B
B
A
B
B
F C
C
D ISOLATION VALVES
B
How often you check for water in the fuel and replace the filter element depends on the quality of the fuel used and the level of
contaminants it contains.
Note: the presence of water in the filter is easy to check ; with water having a greater density than the fuel, it will sink to the bottom of
the transparent bowl, appearing as a different colour to the lighter density oil above.
8.4.2.1.2 Bleeding
1. Shut down the generating set and wait for the engine to cool in order to avoid any risk of fire.
2. If the filters fitted in series are equipped with an isolation valve, alternately isolate the filter being purged
2. Place a container under the water drain tap.
3. Unscrew (around 2 turns) the water drain tap on the bowl and the air vent valve (if present). Drain the water.
4. Close the water drain tap and the air vent valve
5. Make sure the drain tap and vent valve are closed tightly.
PRELIMINARY OPERATIONS:
1. Shut down the generating set and wait for the engine to cool in order to avoid any risk of fire.
2. Close the isolation valve between the tank and the filter if applicable.
3. If the filters are fitted in series and are equipped with an isolation valve, alternately isolate the filter being replaced.
Generally, the replacement instructions will come with the spare filter.
If necessary when finished replacing the filter, drain the fuel supply circuit.
The procedure for priming the fuel supply circuit is generally described in the engine manufacturer manual. Follow these
recommendations.
Engines equipped with an automatic priming system do not require manual priming.
1st case: Without priming pump (the fuel source must be higher than the filter inlet)
1. Place a container under the air bleed valve to catch any fuel.
2. Open the shut-off valve which allows fuel to be supplied to the engine.
3. Unscrew (around 2 turns) the air bleed screw on the fuel filter until the fuel flows without bubbles.
4. Close the air bleed screw.
5. Start the engine and check there are no leaks.
2nd case: With a manual priming pump, without manual air bleed
1. Open the shut-off valve which allows fuel to be supplied to the engine.
2. Work the priming pump until it becomes difficult to pump (pressure point).
3. Wait a minute then repeat.
4. Start the engine and check there are no leaks.
3nd case: With a manual priming pump and manual air bleed
1. Place a container under the air bleed valve to catch any fuel.
2. Open the shut-off valve which allows fuel to be supplied to the engine.
3. Unscrew (around 2 turns) the air bleed screw on the fuel filter.
4. Work the priming pump until the fuel flows without bubbles.
5. Close the air bleed screw. Continue to work the priming pump until it becomes difficult to pump (pressure point).
6. Start the engine and check there are no leaks.
Coolant is flammable.
Liquid escaping suddenly from the cooling system may cause serious burns.
DANGER Wear protective clothes, rubber gloves and protective goggles.
Shut down the engine.
Do not remove the fill cap until it has cooled enough to be turned with bare hands. Start by
turning the cap on the expansion tank to the first notch to release the pressure, then remove it
completely.
After draining the cooling system, several successive refills are necessary to completely fill the circuit.
IMPORTANT Before starting to refill, make sure you have enough new coolant for the whole system (engine, pipes, radiator,...).
In order to correctly compare the results, it is necessary to make sure of the representativeness of the samples by means of a suitable
sampling method.
Regular analyses of the coolant will allow you to prevent engine problems well before they present themselves, improve the running
of equipment and reduce costly repairs.
The test can detect:
- cavitation corrosion
- chemical distribution ;
- leakage of combustion gases ;
- contamination ;
- electrical earthing problems.
When in severe conditions of use, analyses should be carried out more frequently, for example when:
- in extreme climatic conditions ;
- subject to repeated starts ;
- the engine is often running for a long time on low load ;
Some signs that the coolant is no longer carrying out its function may include:
- Engine Overheating ;
- colour alteration ;
- deposits present.
SAMPLING POINT:
Sampling is carried out at a representative point in the system, preferably just after the machine is shut down:
- always at the designated sampling point(s)
- if not, then by the radiator coolant drain valve after draining the polluted fluid at the bottom of the radiator ;
SAMPLING METHOD:
8.4.3.3 Draining
Preliminary operations
1. Place a suitable container to collect the coolant under the drain valves and caps.
2. Turn off the pre-heating element (if applicable)
Drainage procedure:
1. Turn the cap on the expansion tank to the first notch to release the pressure, then remove it completely.
2. Open the drain points and let the coolant flow from the following locations (depending on the configuration):
- radiator drain valve ;
- engine block ;
- pre-heater group;
- coolant pump body ;
- Injection pump ;
- thermostat case
- any cooling system pipes equipped with a drain.
3. Close all the open drainage points.
4. Put the expansion tank cap in place and close.
Prioritise filling with the help of a pump, through the lowest point in the circuit.
1. Connect a suitable pump to the lowest drain point with a flexible hose.
2. Loosen the permanent aeration points and the air bleed points. It is sometimes necessary also to bleed the body of the
pump and the thermostat housing.
3. Turn the cap on the expansion tank to the first notch to release the pressure, then remove it completely.
4. Open the drain valve and fill the cooling circuit using the pump to a pressure of at least 0.5 bar.
5. During filling, when the liquid begins to flow without any bubbles, close, in succession, the drain and bleed points.
6. Fill the circuit until the level in the expansion tank is at its maximum.
7. Close the drain valve.
8. Check that the expansion tank cap is in good condition, clean the sealing surfaces if necessary.
9. Put the cap in place and close it.
10. Make sure there are no leaks anywhere in the cooling system.
11. Dismantle and clean the pump and hose.
1. Turn the cap on the expansion tank to the first notch to release the pressure, then remove it completely.
2. Loosen the permanent aeration points and the air bleed points. It is sometimes necessary also to bleed the body of the
pump and the thermostat housing.
3. Pour the coolant into the expansion tank.
4. During filling, when the liquid begins to flow without any bubbles, close, in succession, the drain and bleed points.
5. Fill the expansion tank until it reaches the maximum level.
6. Check that the expansion tank cap is in good condition, clean the sealing surfaces if necessary.
7. Put the cap in place and close it.
8. Cut off the fuel supply and start the engine for 10 seconds maximum.
9. Make sure there are no leaks anywhere in the cooling system.
10. Turn the cap on the expansion tank to the first notch to release the pressure, then remove it completely.
11. Top up the cooling liquid until it reaches the max. level.
12. Put the cap in place and close it.
13. Start the engine again and repeat the operations described in the previous steps of this procedure as many times as
necessary until it is no longer necessary to top up the coolant.
1. Start the engine without load until the water temperature reaches 60-70 °C.
2. Shut down the engine and let it cool down.
3. Make sure there are no leaks anywhere in the cooling system.
4. Turn the cap on the expansion tank to the first notch to release the pressure, then remove it completely.
5. Top up the cooling liquid until it reaches the max. level.
6. Start the engine again and repeat the operations described in the previous steps of this procedure as many times as
necessary until it is no longer necessary to top up the coolant.
Check the coolant level in the expansion tank for the next two starts.
Certain manufacturer documentation use only a clogging indicator to define air filter maintenance.
If such an indicator is absent, and without an additional servicing indication, the filter(s) should be
replaced at least yearly, or more often if necessary.
IMPORTANT
Certain generating sets are equipped with air filters for dusty environments : maintenance requirements for these filters is determined
by checking the maintenance indicator provided on these filters.
Note: The maintenance indicator may be specific to, or an original part by, the engine manufacturer. The maintenance indicator is
mounted on the engine air intake, just after the air filter.
Maintenance frequency
- Do not judge the condition of the filter by its visual appearance.
- Carrying out maintenance too frequently may cause :
Damage to the filter cartridge ;
Incorrect installation of the filter cartridge ;
Accidental introduction of dust into the engine.
If the air filter is fitted with a dust removal valve (A), press on the B
tip of the valve to remove accumulated dust particles.
Check the maintenance indicator on the air filter (B). when the
indicator is red :
These operations must only be carried out when the generating set is shut down.
These operations must only be carried out by qualified personnel.
IMPORTANT
1. Carefully remove the cartridge. 2. Thoroughly clean the inside of the filter body as well as
the parts in contact with the seals, with a clean, damp
cloth.
3. Check the condition and elasticity of the seals on 4. Install the new cartridge and carefully close the cover.
the new filter cartridge.
5. Check that the whole air intake circuit is sealed 6. Reset the maintenance indicator by pushing the button
marked C after changing the filter cartridge.
DANGER
Risk of explosion or fire (oxygen and hydrogen present). The battery must never be
exposed to any naked flames or sparks.
Risk of sparks forming and an explosion. When fitting the battery, never invert the
polarities.
Do not short the battery terminals with a tool or other metal object.
Risk of injury. Battery electrolyte is extremely corrosive. Always protect your eyes, skin
and clothing when handling batteries. Always wear protective goggles and gloves.
In the event of contact with the skin, wash thoroughly with water and soap. If the eyes are
splashed, rinse thoroughly with water and consult a doctor immediately.
After the battery has been topped up, it must be recharged for at least 30 minutes.
The results of the density and voltage measurements make it possible to define the charge status of the battery. If the charge status
is less than 60%, the battery must be recharged.
Highly discharged or sulphated batteries (formation of whitish lead sulphate deposit on the plates, which becomes hard) can no longer
regenerate or be charged in a generating set.
A discharged battery should be recharged immediately, or else it will suffer irreparable damage.
IMPORTANT
Battery charge
Example of charge:
- 12V 60 Ah battery = 6 A charging current;
- Charge status: 50% (acid density 1.19 and voltage when idle 12.30V);
- The battery is short 30 Ah, and this must be recharged.
- Charge factor: 1.2;
- 30 Ah x 1.2 = 36 Ah to be charged;
- Charging current: 6A, approximately 6 hours charging required; the charging current
must always be 1/10th of the nominal capacity of the battery.
Recharging is complete when the battery voltage and the acid density stop increasing.
The power of the charger must be suitable for the battery to be charged and the charging time available.
Note: if several batteries connected together are being recharged, the following points must be checked:
- Are the batteries connected in series?
- Is the voltage chosen exact? 1 battery x 12 V, 3 x 36V batteries.
- Adjust the charge current to the lowest battery.
- The power difference between the batteries must be as low as possible.
Keep the batteries clean and dry. The presence of impurities and rust on the battery and
terminals may cause the current jumps, voltage drops and the battery to discharge,
particularly in humid weather.
1. Clean any signs of oxidation on the battery terminals and the cable terminals using a
brass brush.
2. Fully tighten the cable terminals and lubricate them with grease for battery terminals or
vaseline. A terminal which is not secured correctly may cause sparks and therefore
lead to an explosion.
IMPORTANT
Regularly check that the harness fins are not clogged and clean as often as local conditions require. Note: The cleanliness of the
device is a factor which will determine its performance and length of service life.
As the engines are fitted with an oil vapour recirculation system, the harness should not get greasy. As a general rule, using
compressed air directed parallel to the fins should be sufficient to clean the harness.
In all cases, cleaning should be undertaken with care to ensure the surface of the fins is not damaged.
IMPORTANT
Drain
point
LT circuit
Drain
point
HT circuit
4. Carry out the same procedure for the other fans. 5. Remove the fan support panels.
6. Disconnect the servomotors from the motorised 7. Remove the motorised ventilation flap to gain access to
ventilation flap. the harness.
Servomotors Motorised
ventilation flap
Servomotor
connection unit
8. Using an industrial vacuum cleaner, remove all foreign bodies that might obstruct the harness. Blow the harness with
compressed air, if necessary.
9. If there are any traces of grease, use commercial solvents to clean the harness.
10. Refit the components in the reverse order to removal, then close the circuits and fill the harness with antifreeze coolant.
This section contains general descriptions and maintenance procedures concerning additional equipment which may be fitted to our
generating sets.
Maintenance must only be carried out when the generating set or installation is switched off, and the engine
and its components have cooled down.
IMPORTANT
The user must carry out the following checks annually (or more frequently if the installation or operating conditions require):
- check the mechanical performance of the components;
- check the tightness of the various fastenings;
- check that the drainage system operates correctly (cf. condensate collector);
- periodic cleaning of spark arresters if fitted to the silencer;
- periodic check of the catalytic converters (efficiency and condition) if fitted to the silencers.
Deadlines:
Every week: check that the connections are well sealed and there are no leaks.
Every month: check the condition of the pump cover and body and keep it clean.
For a pump used every two or three days there is no special maintenance.
At the beginning of winter, drain the pump, protect it from freezing by wrapping it or disassembling and keeping it protected.
For a pump which isn't regularly used it is necessary after each usage to strictly follow the following instructions:
- make sure the pump is completely drained.
- lubricate the pump to make sure it doesn't rust.
IMPORTANT
Compliance with these instructions is essential to keep the pumps in good working order:
1. Remove the top fitting
2. Tilt the pumps piston to 55° with the lever
3. Using an oil syringe equipped with an elbow fitting, apply a small amount of vaseline oil onto the
cylindrical wall of the pump body. Tilt the piston to the other side and perform the same operation,
always with a very small dose.
4. Work the lever a dozen times, through the full range of movement, in order to distribute the
lubricant to all the edges of the pump body.
5. Then leave the lever in the upright position.
6. Replace the fitting
Following a maintenance fault on a pump which hasn't been used for several weeks, the mechanism is at risk of
becoming blocked by rust on the cast iron components.
IMPORTANT In this case, it will be necessary to dismantle the pump (contact one of our agents).
In case of major difficulty using the lever during pumping, do not force it, and check to make sure there are no foreign bodies in the
suction circuit, drain the pump.
1. Lever
2. Cap
3. Piston + valves + pins
4. Seat + valves + pins
5. Body
6. Fittings and seals
7. Felt seal + O-ring + fittings
8. Packing gland + ring + packing
Sealing on EP, BP and HL series pumps is done using a packing gland and ET209 packing made of ramie yarn impregnated with
PTFE. The rotation speed of the piston pin is low and cannot cause wear of the piston even when it is dry.
This system cannot be sealed 100% and requires regular monitoring in-situ.
In case of leakage, the packing must be compressed by tightening the two bolts, gently and alternately, on the oval gland which rests
on a ring. This compresses the packing in its housing. After tightening, check the effort it takes to work the pump. The movement
should remain easy.
The advantage of this solution is that it is possible to make adjustments to the sealing externally without disassembling the cover of
the pump.
There is a complete seal kit.
Draining:
A small valve or screw, on the piping about 0.70 m below the pump, is indispensable. In case of prolonged periods without use, drain
the pump and apply some vaseline oil, by spray if possible, in order to avoid blockage of the internal components.
A generating set which is left unused may have a damaging effect on the engine and alternator. To reduce these effects, it is advisable
to prepare and store the generating set correctly.
Storing batteries
- Batteries ready for use must be stored in a cool and dry place (frost-free) protected from the sun.
- Batteries must be transported and stored in a vertical position to prevent any risk of acid spillage.
- Leave the terminal cover on the positive terminal.
If the problem persists, call upon an agent for assistance. The serial numbers of the generating set, the engine, alternator and possibly
the control unit (if equipped) are often necessary.
MGS_186_EN _17/07/2017 15:01 33532000201_6_1 Section_10 _Rapid identification of minor malfunctions 129
10.2 Starter batteries
Fault observed Probable origin Measures or observations
Incorrect composition Cool
The acid heats up when a new battery is
Incorrect storage Charge the battery
filled
Prolonged storage in a damp place Check the acid density
The acid escapes through the filler holes The battery is too full Reduce the battery fluid level
Battery tray not leaktight Replace the battery
Acid level too low Considerable formation of gas due to a Check the charger and repair if
very high charging voltage necessary
Insufficient charge
Acid level too low Recharge the battery
Short circuit in the power circuit
Incorrect operation from start-up Check the electrical installation
Consumption fault
The battery has been filled with acid Reduce the acid level and fill with distilled
Acid density too high
instead of water water. Repeat the operation if necessary
Battery empty Recharge the battery
Starting problems Battery exhausted or faulty
Starting test incorrect Capacity too low Replace the battery
Battery sulphated
Incorrect battery part no Define the correct battery part no. for the
recommended use
Short service life
Repeated deep discharging It is recommended to charge the battery
Battery stored too long without charge using a regulator
Overload
High water consumption Check the charger (voltage regulator).
Charging voltage too high
Sparks after battery charging
Short circuit
Connection or disconnection during
The battery explodes Replace the battery
charging
Internal fault (for example: interruption)
and low electrolyte level
130 Section 10 Rapid identification of minor malfunctions 33532000201_6_1 MGS_186_EN _17/07/2017 15:01
10.3 JAPY manual pump
The pumps do not have any particular maintenance requirements. Check for leaks around the seals if necessary.
Fault finding and resolution
Suction height too high Bring the pump closer to the fluid to be pumped
MGS_186_EN _17/07/2017 15:01 33532000201_6_1 Section_10 _Rapid identification of minor malfunctions 131
11 Glossary
European Agreement Concerning the International Carriage of Dangerous Goods by Road: this
agreement stipulates the conditions for the merchandise involved, notably their packaging and labels,
ADR
and the conditions notably for the construction, equipment, and use of the vehicle transporting the
materials involved.
AIPR designates electrical equipment (cabinet or box) which houses the main circuit breaker
AIPR (downstream from the power alternator) and the auxiliary outgoing feeders. The AIPR is generally
mounted on the generating set base frame. It is used for housing circuit breakers of 800 A or more.
Auxiliaries
The electrical auxiliaries of a generating set comprise the electrical equipment which ensures the
(auxiliary electrical
correct operation of the generating set, in particular that of the internal combustion engine: battery
equipment of a generating
charger, preheating of the internal combustion engine, electric fuel supply pump, etc.
set)
Retention tank This is a vessel for collecting generating set leaks, to prevent them from polluting the environment.
Welding seam This is a welding bead.
Box This is the common name given to an ISO container.
Generating set connection terminal identified by a PE marking or by a standardised "Earth" symbol and
Earth terminal
provided to enable the generating set to be earthed. This terminal is internally connected to the earth
(of a generating set)
of the generating set and, according to the earthing system diagram (SLT), to the alternator neutral.
Low Voltage Low Voltage A: 50 V <LVA < 500 V alternating current
LV
Low Voltage B: 500 V <LVB < 1000 V alternating current
Multipolar cable Cable comprising more than one insulated conductor.
Tripolar cable Multipolar cable comprising three insulated conductors.
Single pole cable Cable comprising a single insulated conductor.
Checking the rotating field on a three-phase installation involves checking the rotation direction of the
phases using an instrument (phase rotation tester or rotophaser): when the instrument's connectors,
Rotating field
phase 1, phase 2, and phase 3, are connected to the corresponding phases of the network being
(rotating field check)
checked, the display on the instrument indicates whether or not the order 1-2-3 indicated by the
markings on the tested conductors (terminals, cables) is correct.
Application (or performance) classes: G1, G2, G3 and G4.
Standardised performance classes for generating sets defined by standard ISO 8528-1:
They define the particular requirements concerning precision and stability for the voltage and frequency
of a generating set during load variations in the installation to be supplied.
- Class G1: for an application where the connected loads are such that only basic parameters
of voltage and frequency are required;
Application classes
- Class G2: for an application where the demands on voltage characteristics are very much the
(or performance classes)
same as for the commercial power system;
- Class G3: for an application where the connected equipment may make severe demands on
frequency, voltage and waveform characteristics (for example: telecommunications and
thyristor-controlled loads);
- Class G4: for applications where the demands made on the frequency, voltage and waveform
characteristics are exceptionally severe (for example: data-processing equipment).
Output class: COP, PRP, LTP, ESP, DCP and MAX.
Output class
Standardised output class of a generating set defined by standard ISO 8528-1 and ISO 8528-8.
Standardised fitting on all 8 corners of ISO containers enabling containers to be handled and
ISO corner casting
transported.
IMD Insulation monitoring device.
CSC
-
A three-phase generating set is designed and protected (circuit breaker setting) to be able to
Apparent power (kVA) provide its rated active power (kW) to an installation whose power factor (PF) can vary from 1
to 0.8.
- The rated apparent power (kVA) indicated on the identification plate of a three-phase
generating set is determined for a rated power factor (PF) of 0.8 and is therefore equal to the
rated active power (kW) divided by 0.8.
For example: If the rated active power of a three-phase generating set is 80 kW, the rated apparent
power in kVA is: 80 / 0.8 = 100 kVA.
- When the rated power factor (PF) indicated on the identification plate of a single-phase
generating set is 1, the rated apparent power (kVA) is equal to the rated active power (kW).
Maximum power in kW that a generating set is capable of supplying continuously under a constant load
for an unlimited number of hours per year, under the agreed operating conditions, provided that the
maintenance intervals and operating modes are observed in accordance with the manufacturer's
requirements.
Legend
t time
P power
a
Continuous power (100%)
Maximum power in kW that a generating set is capable of supplying continuously under a variable load
for an unlimited number of hours per year, under the agreed operating conditions, provided that the
maintenance intervals and operating modes are observed in accordance with the manufacturer's
requirements.
The mean admissible power (Ppp) over a 24-hour period must not exceed 70% of the main power,
unless otherwise agreed by the manufacturer of the heat engine.
Legend
t time
P power
a
Prime power (100%)
b
Average permissible power in a 24h period (P pp)
c Actual average power in a 24h period (P pa)
d Shutdown
NOTE t1 + t2 + t3 + … … … + tn = 24h
Emergency Standby
Power: ESP
Legend
t time
P power
a
Emergency standby power (ESP)
b
Average permissible power in a 24h period (P pp)
c Actual average power in a 24h period (P pa)
d Shutdown
NOTE t1 + t2 + t3 + … … … + tn = 24h
Maximum power in kW that a generating set is capable of supplying up to 500 hours per year, under
the agreed operating conditions, provided that the maintenance intervals and operating modes are
observed in accordance with the manufacturer's requirements.
NOTE: The limited running time power (100%) is limited to a maximum of 500 hours per year.
Legend
t time
P power
Limited time power (LTP)
The power given by multiplying the current and voltage that the generating set is capable of providing
for at least 5 minutes within the following voltage and frequency limits.
Note 1: The prescribed output voltage must be within ± 10 % of the rated voltage and the output frequency must be
Maximum power: MAX within ± 8% of the nominal frequency.
Note 2: The protection device must not be activated within 5 minutes and the overload conditions must satisfy the
requirements of paragraph 6.4 Overload conditions from ISO 8528-8. The minimum ratio between rated power
(COP) and maximum power (MAX) should be such that Pnominal/Pmax ≥ 0,75.
Term sometimes used to designate the earthing system (SLT in French) of an installation (see
Earthing system
paragraph "Earthing system").
Differential device which only detects the fault current to earth in an electrical circuit. It is designed to
Differential relay be connected to the control of a circuit breaker which it opens in order to cut off the electrical supply
when a fault current is detected.
Controller
APM303
Soft version : 1.1.0
33502030901_1_1
23/01/2015
The "user level" user manual is designed for users who are qualified to set up an
installation (generating set and environment). These users must be able to monitor
that the generating set is operating correctly (start, stop, basic settings), to interpret
any indications (mechanical, electrical) and may be required to check one or more
parameters.
The "operator level" user manual is designed for those who – in addition to the skills
required for users – have the skills required to modify one or more parameters, to
change the operation of an installation (generating set and environment). To do this,
the operator will have completed training provided by the manufacturer beforehand.
The "specialist level" user manual is designed for those who – in addition to the
skills required for operators – have the skills required to make any special or complex
modification to an installation (generating set and environment). To do this, the
specialist will have completed training provided by the manufacturer beforehand.
APM303 - QUICK START GUIDE page 1/2
abbreviations used: GS = Generating Set 5 - Operation in MANUAL mode: GS off
ATS = Automatic Transfer Switch Manually open the GS circuit breaker (the power is cut
1 - Safety instructions off).
Read the safety instructions on starting up Allow the engine to cool down for 3 minutes.
a GS. Press the STOP button, the RUN LED goes off, the engine
(see General and Safety Manual) stops.
When the GS is off, the control unit may be powered by a
dangerous voltage (preheating, battery charger). 6 - Operation in AUTO mode
When on, the APM303 is powered by a dangerous voltage.
The APM303 has been factory preconfigured; modifying its The AUTO mode is active only if the AUTO LED is fixed.
parameters may make the generating set unstable.
Check that the GS circuit breaker is closed.
Press the AUTO button, the AUTO LED lights up, AUTO mode
2 - Powering on is selected.
Close the battery isolator (if fitted), Start up is possible if the ALARM! LED is off.
Turn the switch on the front of the central console ON (if fitted). Start-up is launched on activation of the remote start/stop,
input, which must be a () potential-free contact (no AC or DC
3 - Checks before starting voltage).
Battery voltage, () e.g. coming from a self-regulating ATS.
Engine oil level,
Coolant level, On activation of the input, the RUN LED flashes and the GS
GS circuit breaker open. starts.
If the ALARM! LED is flashing, refer to section 7. When the voltage and frequency have stabilised, the RUN
4 - Front panel, buttons and LEDs LED becomes fixed and the GS takes over.
On deactivation of the remote start/stop input, the RUN LED
STOP button flashes.
stops the GS and After a cooling period (3 minutes) (), the GS stops and the
acknowledges the fault (if RUN LED goes off.
ALARM! is flashing) The AUTO LED remains on, the GS is on standby, ready for
AUTO button another start.
selects AUTO or MANUAL () If an ATS is fitted, the total number of cooling periods
mode must be correctly adjusted.
START button
starts the GS MANUAL mode takes priority over active AUTO mode:
- pressing the START button activates MANUAL mode,
LED off - pressing the STOP button stops the GS.
other buttons
LED on access to screens 7 - Appearance of an anomaly
LED flashing (see section 13) If the ALARM! LED flashes (see section 13), this means that
an anomaly (alarm or fault) has been detected.
ALARM! alarm = GS not stopped fault = GS stopped
no anomaly (alarm or fault) To view the anomaly, press or to show the screen
fault detected but cleared below:
anomaly detected (alarm or fault) A C
AUTO
MANUAL mode by default B D
AUTO mode selected
remote start/stop on/engine cooling E
RUN
GS stopped A The anomaly appears with an order number
GS started (MANUAL mode) Pictogram symbolising the anomaly (see sections 9 and
B 11)
start or stop in progress
C Anomaly status (fault only, see section 10)
5 - Operation in MANUAL mode: GS on Number of hours GS has been operating when anomaly
D appeared
MANUAL mode inhibits AUTO mode.
If the ALARM! LED is off (no fault present), it is possible to E See section 13 when flashes
start the GS.
Press the START button, the RUN LED flashes, the GS starts. Note: this screen also shows the events (see section 12).
When the voltage and frequency have stabilised, the RUN LED
8 - Active and inactive alarm
becomes fixed.
active
Manually close the GS circuit breaker; the GS takes load
or is ready to take load.
Check the electrical and mechanical values on the APM303 inactive
screens (see section 13).
An alarm cannot be cleared: it becomes inactive even after
intervention from the user.
APM303 - QUICK START GUIDE page 2/2
9 - List of alarms 13 - Displaying the different screens
Automatic scrolling through 7 screens ( 1 to 6 + INIT).
Battery voltage low or charging alternator not working
1
Manual scrolling through 6 screens ( 1 to 6 ), by pressing
flat battery repeatedly on or .
low fuel level INIT
GS overload
1
inactive, not
cleared main ()
active, cleared 2
after pressing
inactive, cleared
after pressing
start up in AUTO mode When is fixed (after 4 seconds), the list of events and
anomalies can be viewed by pressing .
stop in MANUAL mode
stop in AUTO mode
1
JOHN DEERE
Engine
3029DF120
3029DFS29
3029HFS70 (HF270)
3029TF120
3029TFS29
3029TFS70 (TF270)
4045HF120
4045HFS72 (HF275)
4045HFS73 (HF279)
4045HFS80 (HF280)
4045HFS82 (HF285)
4045HFS83 (HF285)
4045TF120
4045TF220
4045TFS70 (TF270)
6068HF120-153
6068HF120-183
6068HFS55
6068HFS72 (HF275)
6068HFS73 (HF279)
6068HFS76 (HF475)
6068HFS77 (HF475)
6068HFS82 (HF285)
6068HFS83 (HF285)
6068HFS89 (HF485)
6068TF220
OMCD16564
33522039401_6_1
30/09/2014
(QJLQHV 3RZHU 8QLWV IRU
*HQ6HWV 6DUDQ
6WDJH ,, DQG 1RQ(PLVVLRQ
&HUWLILHG
23(5$725
6 0$18$/
'#"#!'
&$/,)251,$
3URSRVLWLRQ :DUQLQJ
:$51,1*
31
,QWURGXFWLRQ
3LVWRQ
/LVW RI HPLVVLRQUHODWHG FRPSRQHQWV
)XHO LQMHFWLRQ SXPS &$/,)251,$ 352326,7,21 :$51,1*
,QWDNH PDQLIROG 'LHVHO HQJLQH H[KDXVW DQG VRPH RI LWV FRQVWLWXHQWV DUH NQRZQ
7XUERFKDUJHU WR WKH 6WDWH RI &DOLIRUQLD WR FDXVH FDQFHU
&KDUJH DLU FRROLQJ V\VWHP ELUWK GHIHFWV DQG RWKHU UHSURGXFWLYH KDUP
&'(' 6(3
31
,QWURGXFWLRQ
31
&RQWHQWV
3DJH
3DJH
,GHQWLILFDWLRQ 9LHZV
,GHQWLILFDWLRQ YLHZV )ROORZ 6DIHW\ ,QVWUXFWLRQV
+DQGOH )XHO 6DIHO\²$YRLG )LUHV
+DQGOH 6WDUWLQJ )OXLG 6DIHO\
0DLQWHQDQFH 5HFRUGV +DQGOLQJ %DWWHULHV 6DIHO\
8VLQJ 0DLQWHQDQFH 5HFRUGV ,OOXPLQDWH :RUN $UHD 6DIHO\
+RXUV RI 2SHUDWLRQ ,QVWDOO $OO *XDUGV
+RXUV RI RSHUDWLRQ /LYH :LWK 6DIHW\
+RXUV RI RSHUDWLRQ 3UHSDUH IRU (PHUJHQFLHV
+RXUV RI RSHUDWLRQ 3UHYHQW 0DFKLQH 5XQDZD\
+RXUV RI RSHUDWLRQ 5HFRJQL]H 6DIHW\ ,QIRUPDWLRQ
+RXUV RI RSHUDWLRQ 5HPRYH 3DLQW %HIRUH :HOGLQJ RU +HDWLQJ
+RXUV RI RSHUDWLRQ
5HSODFH 6DIHW\ 6LJQV
+RXUV RI RSHUDWLRQ
3DUN 0DFKLQH 6DIHO\
+RXUV RI RSHUDWLRQ
3UDFWLFH 6DIH 0DLQWHQDQFH
+RXUV RI RSHUDWLRQ
3UHYHQW $FLG %XUQV
+RXUV RI RSHUDWLRQ
3UHYHQW %DWWHU\ ([SORVLRQV
+RXUV RI RSHUDWLRQ
3URWHFW $JDLQVW +LJK 3UHVVXUH 6SUD\
+RXUV RI RSHUDWLRQ
3URWHFW $JDLQVW 1RLVH
+RXUV RI RSHUDWLRQ
6HUYLFH DQG 2SHUDWH &KHPLFDO
+RXUV RI RSHUDWLRQ
6SUD\HUV 6DIHO\
+RXUV RI RSHUDWLRQ
6HUYLFH &RROLQJ 6\VWHP 6DIHO\
+RXUV RI RSHUDWLRQ 6HUYLFH 0DFKLQHV 6DIHO\
+RXUV RI RSHUDWLRQ 6WD\ &OHDU RI 5RWDWLQJ 'ULYHOLQHV
+RXUV RI RSHUDWLRQ 6XSSRUW 0DFKLQH 3URSHUO\
+RXUV RI RSHUDWLRQ 8QGHUVWDQG 6LJQDO :RUGV
+RXUV RI RSHUDWLRQ 8VH 3URSHU /LIWLQJ (TXLSPHQW
8VH 3URSHU 7RROV
6HULDO 1XPEHUV 8VH 6WHSV DQG +DQGKROGV &RUUHFWO\
3RZHU7HFK ODEHO :HDU 3URWHFWLYH &ORWKLQJ
(QJLQH VHULDO QXPEHU SODWH :RUN LQ &OHDQ $UHD
5HFRUG HQJLQH VHULDO QXPEHU :RUN ,Q 9HQWLODWHG $UHD
(QJLQH RSWLRQ FRGHV
5HFRUG IXHO LQMHFWLRQ SXPS PRGHO QXPEHU
)XHOV /XEULFDQWV DQG &RRODQW
5HFRUG (QJLQH &RQWURO 8QLW (&8
'LHVHO )XHO
6HULDO 1XPEHU
+DQGOLQJ DQG 6WRULQJ 'LHVHO )XHO
5HFRUG +LJK3UHVVXUH )XHO 3XPS
'LHVHO (QJLQH %UHDN,Q 2LO ²
0RGHO 1XPEHU
1RQ(PLVVLRQV &HUWLILHG DQG
&HUWLILHG 7LHU 7LHU 7LHU 6WDJH
6DIHW\ , 6WDJH ,, DQG 6WDJH ,,,
$YRLG +DUPIXO $VEHVWRV 'XVW 'LHVHO (QJLQH 2LO ² 1RQ(PLVVLRQV
$YRLG +HDWLQJ 1HDU 3UHVVXUL]HG )OXLG /LQHV &HUWLILHG DQG &HUWLILHG 7LHU DQG
$YRLG +LJK3UHVVXUH )OXLGV 6WDJH ,
&DOLIRUQLD 3URSRVLWLRQ :DUQLQJ /XEULFDQW 6WRUDJH
'LVSRVH RI :DVWH 3URSHUO\ 0L[LQJ RI /XEULFDQWV
'R 1RW 2SHQ +LJK3UHVVXUH )XHO 6\VWHP 'LHVHO (QJLQH &RRODQW HQJLQH ZLWK
([KDXVW )LOWHU &OHDQLQJ ZHW VOHHYH F\OLQGHU OLQHUV
L
31
&RQWHQWV
3DJH 3DJH
LL
31
&RQWHQWV
3DJH
6WRUDJH
(QJLQH VWRUDJH JXLGHOLQHV
3UHSDUH (QJLQH IRU /RQJ 7HUP 6WRUDJH
5HPRYH (QJLQH IURP /RQJ 7HUP 6WRUDJH
6SHFLILFDWLRQV
*HQHUDO HQJLQH SDFN VSHFLILFDWLRQV
1RQ(PLVVLRQ &HUWLILHG (QJLQHV
*HQHUDO HQJLQH SDFN VSHFLILFDWLRQV
6WDJH ,, (PLVVLRQ &HUWLILHG (QJLQHV
*HQHUDO HQJLQH SDFN VSHFLILFDWLRQV
(3$ 7LHU (PLVVLRQ &HUWLILHG (QJLQHV
*HQHUDO HQJLQH SDFN VSHFLILFDWLRQV
(3$ 7LHU (PLVVLRQ &HUWLILHG (QJLQHV
8QLILHG ,QFK %ROW DQG 6FUHZ 7RUTXH 9DOXHV
0HWULF %ROW DQG 6FUHZ 7RUTXH 9DOXHV
LLL
31
&RQWHQWV
LY
31
,GHQWLILFDWLRQ 9LHZV
,GHQWLILFDWLRQ YLHZV
&' ²81²-$1
')
&RQWLQXHG RQ QH[W SDJH '36*&' $35
31
,GHQWLILFDWLRQ 9LHZV
&' ²81²-$1
+)
&RQWLQXHG RQ QH[W SDJH '36*&' $35
31
,GHQWLILFDWLRQ 9LHZV
31
,GHQWLILFDWLRQ 9LHZV
&' ²81²$35
+)8
'36*&' $35
31
0DLQWHQDQFH 5HFRUGV
8VLQJ 0DLQWHQDQFH 5HFRUGV
7R REWDLQ WKH EHVW SHUIRUPDQFH HFRQRP\ DQG VHUYLFH OLIH
IURP \RXU HQJLQH HQVXUH VHUYLFH LV FDUULHG RXW DFFRUGLQJ -RKQ 'HHUH RLOV DQG FRRODQWV KDYH EHHQ IRUPXODWHG
WR WKLV SUHVHQW PDQXDO DQG UHFRUGHG LQ WKH IROORZLQJ WR JLYH PD[LPXP SURWHFWLRQ DQG SHUIRUPDQFH WR \RXU
SDJHV ,W LV UHFRPPHQGHG WKDW \RXU HQJLQH 'LVWULEXWRU HQJLQH :H UHFRPPHQG RQO\ JHQXLQH -RKQ 'HHUH VHUYLFH
RU \RXU 'HDOHU FDUU\ RXW WKLV VHUYLFH ZRUN DQG VWDPS WKH SURGXFWV DQG UHSODFHPHQW SDUWV
DSSURSULDWH FDVH 7R SURWHFW \RXU ULJKWV XQGHU WKH ZDUUDQW\ HQVXUH DOO
.HHSLQJ DQ DFFXUDWH DFFRXQW RI DOO VHUYLFH SHUIRUPHG RQ VFKHGXOHG VHUYLFHV DUH FDUULHG RXW DQG UHFRUGHG ,I \RXU
\RXU HQJLQH ZLOO JLYH PRUH YDOXH WR WKH PDFKLQH ZKHQ HQJLQH LV FRYHUHG E\ H[WHQGHG ZDUUDQW\ LW LV LPSRUWDQW WR
UHVHOO LW PDLQWDLQ WKLV UHFRUG IRU WKH GXUDWLRQ RI WKH ZDUUDQW\
'36*&' 0$<
'DWH
'36*&' 0$<
31
0DLQWHQDQFH 5HFRUGV
'DWH
'36*&' -$1
'DWH
'36*&' -$1
31
0DLQWHQDQFH 5HFRUGV
'DWH
'36*&' -$1
'DWH
'36*&' $35
31
0DLQWHQDQFH 5HFRUGV
'DWH
'36*&' $35
'DWH
'36*&' -$1
31
0DLQWHQDQFH 5HFRUGV
'DWH
'36*&' -$1
'DWH
'36*&' $35
31
0DLQWHQDQFH 5HFRUGV
'DWH
'36*&' -$1
'DWH
'36*&' $35
31
0DLQWHQDQFH 5HFRUGV
'DWH
'36*&' -$1
'DWH
'36*&' $35
31
0DLQWHQDQFH 5HFRUGV
'DWH
'36*&' -$1
'DWH
'36*&' -$1
31
0DLQWHQDQFH 5HFRUGV
'DWH
'36*&' $35
'DWH
'36*&' $35
31
0DLQWHQDQFH 5HFRUGV
'DWH
'36*&' -$1
'DWH
'36*&' -$1
31
0DLQWHQDQFH 5HFRUGV
'DWH
'36*&' -$1
'DWH
'36*&' $35
31
6HULDO 1XPEHUV
3RZHU7HFK ODEHO
$ ODEHO LV ORFDWHG RQ WKH URFNHU DUP FRYHU ZKLFK LGHQWLILHV
HDFK HQJLQH DV D -RKQ 'HHUH 3RZHU7HFK HQJLQH
5* ²81²-$1
'36*&' -8/
&' ²81²6(3
5* ²81²-$1
(DFK HQJLQH KDV D ±GLJLW -RKQ 'HHUH VHULDO QXPEHU 7KH DQG HQJLQHV DQG QHDU WKH IXHO VXSSO\ SXPS
ILUVW WZR GLJLWV LGHQWLI\ WKH IDFWRU\ WKDW SURGXFHG WKH HQJLQH RQ DQG HQJLQHV
´&'´ LQGLFDWHV WKH HQJLQH ZDV EXLOW LQ 6DUDQ )UDQFH
<RXU HQJLQH
V VHULDO QXPEHU SODWH $ LV ORFDWHG RQ WKH
ULJKWKDQG VLGH RI F\OLQGHU EORFN EHKLQG WKH IXHO ILOWHU IRU
'36*&' -$1
31
6HULDO 1XPEHUV
&'% ²81²$8*
BBBBBBBBBBBBBBBBBBB
(QJLQH 0RGHO 1XPEHU &
BBBBBBBBBBBBBBBBBBB
&RHIILFLHQW RI $EVRUSWLRQ 9DOXH '
DQG HQJLQH SODWH
BBBBBBBBBBBBBBBBBBB
&'$ ²81²-$1
DQG HQJLQH SODWH
'36*&' -$1
31
6HULDO 1XPEHUV
&'$ ²81²$8*
(QJLQH RSWLRQ FRGH ODEHO
,Q DGGLWLRQ WR WKH VHULDO QXPEHU SODWH 2(0 HQJLQHV KDYH 7KH ILUVW WZR GLJLWV RI HDFK FRGH LGHQWLI\ D VSHFLILF JURXS
DQ HQJLQH RSWLRQ FRGH ODEHO DIIL[HG WR WKH URFNHU DUP VXFK DV DOWHUQDWRUV 7KH ODVW WZR GLJLWV RI HDFK FRGH
FRYHU 7KHVH FRGHV LQGLFDWH ZKLFK RI WKH HQJLQH RSWLRQV LGHQWLI\ RQH VSHFLILF RSWLRQ SURYLGHG RQ \RXU HQJLQH VXFK
ZHUH LQVWDOOHG RQ \RXU HQJLQH DW WKH IDFWRU\ :KHQ LQ DV D YROW DPS DOWHUQDWRU
QHHG RI SDUWV RU VHUYLFH IXUQLVK \RXU DXWKRUL]HG VHUYLFLQJ
GHDOHU RU HQJLQH GLVWULEXWRU ZLWK WKHVH QXPEHUV 127( 7KHVH RSWLRQ FRGHV DUH EDVHG RQ WKH ODWHVW
LQIRUPDWLRQ DYDLODEOH DW WKH WLPH RI SXEOLFDWLRQ
$Q DGGLWLRQDO VWLFNHU PD\ EH DOVR GHOLYHUHG LQ D SODVWLF 7KH ULJKW LV UHVHUYHG WR PDNH FKDQJHV DW
EDJ DWWDFKHG WR WKH HQJLQH RU LQVHUWHG LQ WKH PDFKLQH DQ\ WLPH ZLWKRXW QRWLFH
GRFXPHQWDWLRQ ,W LV UHFRPPHQGHG WR VWLFN WKLV RSWLRQ
FRGH OLVW VWLFNHU HLWKHU ,I DQ HQJLQH LV RUGHUHG ZLWKRXW D SDUWLFXODU FRPSRQHQW WKH
2Q WKLV SDJH RI \RXU 2SHUDWRU
V PDQXDO EHORZ WKLV ODVW WZR GLJLWV RI WKDW IXQFWLRQDO JURXS RSWLRQ FRGH ZLOO EH
VHFWLRQ RU ;; 7KH OLVW RQ WKH QH[W SDJH VKRZV RQO\ WKH
RU ILUVW WZR GLJLWV RI WKH FRGH QXPEHUV )RU IXWXUH UHIHUHQFH
2Q WKH ´(QJLQH 2ZQHU
V :DUUDQW\´ ERRNOHW XQGHU WKH WLWOH VXFK DV RUGHULQJ UHSDLU SDUWV LW LV LPSRUWDQW WR KDYH WKHVH
237,21 &2'(6 (QJLQH PDQXIDFWXULQJ FRQILJXUDWLRQ FRGH QXPEHUV DYDLODEOH 7R HQVXUH WKLV DYDLODELOLW\ HQWHU
WKH WKLUG DQG IRXUWK GLJLWV VKRZQ RQ \RXU HQJLQH RSWLRQ
127( 7KH 0DFKLQH 0DQXIDFWXUHU PD\ KDYH DOUHDG\ FRGH ODEHO LQ WKH VSDFHV SURYLGHG RQ WKH IROORZLQJ SDJH
VWXFN LW DW D VSHFLILF DFFHVVLEOH SODFH LQVLGH WKH
HQFORVXUH RU FORVH WR D PDLQWHQDQFH DUHD 127( 127( <RXU HQJLQH RSWLRQ FRGH ODEHO PD\ QRW
FRQWDLQ DOO RSWLRQ FRGHV LI DQ RSWLRQ KDV EHHQ DGGHG
7KH HQJLQH RSWLRQ FRGH ODEHO LQFOXGHV DQ HQJLQH EDVH DIWHU WKH HQJLQH OHIW WKH SURGXFLQJ IDFWRU\
FRGH $ 7KLV EDVH FRGH PXVW DOVR EH UHFRUGHG DORQJ ,I RSWLRQ FRGH ODEHO LV ORVW RU GHVWUR\HG FRQVXOW
ZLWK WKH RSWLRQ FRGHV $W WLPHV LW ZLOO EH QHFHVVDU\ WR \RXU VHUYLFLQJ GHDOHU RU HQJLQH GLVWULEXWRU VHOOLQJ
IXUQLVK WKLV EDVH FRGH WR GLIIHUHQWLDWH WZR LGHQWLFDO RSWLRQ WKH HQJLQH IRU D UHSODFHPHQW
FRGHV IRU WKH VDPH HQJLQH PRGHO
31
6HULDO 1XPEHUV
&' ²81²6(3
0DQXIDFWXUHU
V 1R BBBBBBBBBBBBBBBBBBBBBBBBBB
6HULDO 1R BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB
'36*&' -$1
31
6HULDO 1XPEHUV
5* ²81²$35
8QLW (&8 PRXQWHG RQ RU QHDU WKH HQJLQH
3DUW 1R
6HULDO 1R
$²6HULDO 1XPEHU /DEHO 5HFRUG (QJLQH &RQWURO 8QLW (&8 6HULDO 1XPEHU
&' )(%
5* ²81²129
0DQXIDFWXUHU
V 1R
6HULDO 1R
31
6DIHW\
$YRLG +DUPIXO $VEHVWRV 'XVW
$YRLG EUHDWKLQJ GXVW WKDW PD\ EH JHQHUDWHG ZKHQ
KDQGOLQJ FRPSRQHQWV FRQWDLQLQJ DVEHVWRV ILEHUV ,QKDOHG
DVEHVWRV ILEHUV PD\ FDXVH OXQJ FDQFHU
&RPSRQHQWV LQ SURGXFWV WKDW PD\ FRQWDLQ DVEHVWRV
ILEHUV DUH EUDNH SDGV EUDNH EDQG DQG OLQLQJ DVVHPEOLHV
76 ²81²$35
FOXWFK SODWHV DQG VRPH JDVNHWV 7KH DVEHVWRV XVHG LQ
WKHVH FRPSRQHQWV LV XVXDOO\ IRXQG LQ D UHVLQ RU VHDOHG LQ
VRPH ZD\ 1RUPDO KDQGOLQJ LV QRW KD]DUGRXV DV ORQJ DV
DLUERUQH GXVW FRQWDLQLQJ DVEHVWRV LV QRW JHQHUDWHG
$YRLG FUHDWLQJ GXVW 1HYHU XVH FRPSUHVVHG DLU IRU
FOHDQLQJ $YRLG EUXVKLQJ RU JULQGLQJ PDWHULDO FRQWDLQLQJ
DVEHVWRV :KHQ VHUYLFLQJ ZHDU DQ DSSURYHG UHVSLUDWRU
$ VSHFLDO YDFXXP FOHDQHU LV UHFRPPHQGHG WR FOHDQ .HHS E\VWDQGHUV DZD\ IURP WKH DUHD
DVEHVWRV ,I QRW DYDLODEOH DSSO\ D PLVW RI RLO RU ZDWHU RQ
WKH PDWHULDO FRQWDLQLQJ DVEHVWRV
';'867 0$5
76 ²81²0$<
EXUVW ZKHQ KHDW JRHV EH\RQG WKH LPPHGLDWH IODPH DUHD
';725&+ '(&
31
6DIHW\
76 ²81²$35
8VH OHDNSURRI FRQWDLQHUV ZKHQ GUDLQLQJ IOXLGV 'R QRW XVH
IRRG RU EHYHUDJH FRQWDLQHUV WKDW PD\ PLVOHDG VRPHRQH
LQWR GULQNLQJ IURP WKHP
'R QRW SRXU ZDVWH RQWR WKH JURXQG GRZQ D GUDLQ RU LQWR
DQ\ ZDWHU VRXUFH
$LU FRQGLWLRQLQJ UHIULJHUDQWV HVFDSLQJ LQWR WKH DLU FDQ
GDPDJH WKH (DUWK¶V DWPRVSKHUH *RYHUQPHQW UHJXODWLRQV
PD\ UHTXLUH D FHUWLILHG DLU FRQGLWLRQLQJ VHUYLFH FHQWHU WR
,QTXLUH RQ WKH SURSHU ZD\ WR UHF\FOH RU GLVSRVH RI ZDVWH
UHFRYHU DQG UHF\FOH XVHG DLU FRQGLWLRQLQJ UHIULJHUDQWV
IURP \RXU ORFDO HQYLURQPHQWDO RU UHF\FOLQJ FHQWHU RU IURP
\RXU -RKQ 'HHUH GHDOHU
';'5$,1 0$5
76 ²81²0$5
2QO\ WHFKQLFLDQV IDPLOLDU ZLWK WKLV W\SH RI V\VWHP FDQ
SHUIRUP UHSDLUV 6HH \RXU -RKQ 'HHUH GHDOHU
';::+3&5 -$1
';),/7(5 -$1
31
6DIHW\
76 ²81²$35
DYDLODEOH IURP \RXU -RKQ 'HHUH GHDOHU
7KHUH FDQ EH DGGLWLRQDO VDIHW\ LQIRUPDWLRQ FRQWDLQHG RQ
SDUWV DQG FRPSRQHQWV VRXUFHG IURP VXSSOLHUV WKDW LV QRW
UHSURGXFHG LQ WKLV RSHUDWRU
V PDQXDO
/HDUQ KRZ WR RSHUDWH WKH PDFKLQH DQG KRZ WR XVH FRQWUROV
SURSHUO\ 'R QRW OHW DQ\RQH RSHUDWH ZLWKRXW LQVWUXFWLRQ
.HHS \RXU PDFKLQH LQ SURSHU ZRUNLQJ FRQGLWLRQ
,I \RX GR QRW XQGHUVWDQG DQ\ SDUW RI WKLV PDQXDO DQG QHHG
8QDXWKRUL]HG PRGLILFDWLRQV WR WKH PDFKLQH PD\ LPSDLU WKH
DVVLVWDQFH FRQWDFW \RXU -RKQ 'HHUH GHDOHU
IXQFWLRQ DQGRU VDIHW\ DQG DIIHFW PDFKLQH OLIH
';5($' -81
76 ²81²$8*
3UHYHQW ILUHV E\ NHHSLQJ PDFKLQH FOHDQ RI DFFXPXODWHG
WUDVK JUHDVH DQG GHEULV $OZD\V FOHDQ XS VSLOOHG IXHO
8VH RQO\ DQ DSSURYHG IXHO FRQWDLQHU IRU WUDQVSRUWLQJ
IODPPDEOH OLTXLGV
1HYHU ILOO IXHO FRQWDLQHU LQ SLFNXS WUXFN ZLWK SODVWLF EHG
OLQHU $OZD\V SODFH IXHO FRQWDLQHU RQ JURXQG EHIRUH
UHIXHOLQJ 7RXFK IXHO FRQWDLQHU ZLWK IXHO GLVSHQVHU QR]]OH 'R QRW VWRUH IXHO FRQWDLQHU ZKHUH WKHUH LV DQ RSHQ IODPH
EHIRUH UHPRYLQJ FDQ OLG .HHS IXHO GLVSHQVHU QR]]OH LQ VSDUN RU SLORW OLJKW VXFK DV ZLWKLQ D ZDWHU KHDWHU RU RWKHU
FRQWDFW ZLWK IXHO FRQWDLQHU LQOHW ZKHQ ILOOLQJ DSSOLDQFH
';),5( 2&7
';),5( $35
31
6DIHW\
76 ²81²$35
$OZD\V UHPRYH JURXQGHG EDWWHU\ FODPS ILUVW DQG
UHSODFH JURXQGHG FODPS ODVW
6XOIXULF DFLG LQ EDWWHU\ HOHFWURO\WH LV SRLVRQRXV DQG VWURQJ
HQRXJK WR EXUQ VNLQ HDW KROHV LQ FORWKLQJ DQG FDXVH
EOLQGQHVV LI VSODVKHG LQWR H\HV
$YRLG KD]DUGV E\
)LOOLQJ EDWWHULHV LQ D ZHOOYHQWLODWHG DUHD
:HDULQJ H\H SURWHFWLRQ DQG UXEEHU JORYHV
$YRLGLQJ XVH RI DLU SUHVVXUH WR FOHDQ EDWWHULHV
$YRLGLQJ EUHDWKLQJ IXPHV ZKHQ HOHFWURO\WH LV DGGHG
$YRLGLQJ VSLOOLQJ RU GULSSLQJ HOHFWURO\WH
8VLQJ FRUUHFW EDWWHU\ ERRVWHU RU FKDUJHU SURFHGXUH
,I DFLG LV VSLOOHG RQ VNLQ RU LQ H\HV
)OXVK VNLQ ZLWK ZDWHU
$SSO\ EDNLQJ VRGD RU OLPH WR KHOS QHXWUDOL]H WKH DFLG
)OXVK H\HV ZLWK ZDWHU IRU ² PLQXWHV *HW
PHGLFDO DWWHQWLRQ LPPHGLDWHO\
,I DFLG LV VZDOORZHG
'R QRW LQGXFH YRPLWLQJ
'ULQN ODUJH DPRXQWV RI ZDWHU RU PLON EXW GR QRW
H[FHHG / TW
*HW PHGLFDO DWWHQWLRQ LPPHGLDWHO\
:$51,1* %DWWHU\ SRVWV WHUPLQDOV DQG UHODWHG
76 ²81²$8*
DFFHVVRULHV FRQWDLQ OHDG DQG OHDG FRPSRXQGV FKHPLFDOV
NQRZQ WR WKH 6WDWH RI &DOLIRUQLD WR FDXVH FDQFHU DQG
UHSURGXFWLYH KDUP :DVK KDQGV DIWHU KDQGOLQJ
';::%$77(5,(6 '(&
';/,*+7 -81
31
6DIHW\
76 ²81²6(3
:HDU FORVHILWWLQJ FORWKHV 6WRS WKH HQJLQH DQG EH VXUH
IDQV EHOWV SXOOH\V DQG GULYHV DUH VWRSSHG EHIRUH PDNLQJ
DGMXVWPHQWV FRQQHFWLRQV RU FOHDQLQJ QHDU IDQV DQG WKHLU
GULYH FRPSRQHQWV
';*8$5'6 $8*
76 ²²2&7
';/,9( 6(3
76 ²81²$35
';),5( 0$5
31
6DIHW\
76 ²81²-$1
HQJLQH RQO\ IURP RSHUDWRU¶V VHDW ZLWK WUDQVPLVVLRQ LQ
QHXWUDO RU SDUN
';%<3$6 6(3
7 ²81²-81
';$/(57 6(3
76 ²81²$35
5HPRYH SDLQW D PLQLPXP RI PP LQ IURP DUHD
WR EH DIIHFWHG E\ KHDWLQJ ,I SDLQW FDQQRW EH UHPRYHG
ZHDU DQ DSSURYHG UHVSLUDWRU EHIRUH KHDWLQJ RU ZHOGLQJ
,I \RX VDQG RU JULQG SDLQW DYRLG EUHDWKLQJ WKH GXVW
:HDU DQ DSSURYHG UHVSLUDWRU
,I \RX XVH VROYHQW RU SDLQW VWULSSHU UHPRYH VWULSSHU ZLWK
VRDS DQG ZDWHU EHIRUH ZHOGLQJ 5HPRYH VROYHQW RU
SDLQW VWULSSHU FRQWDLQHUV DQG RWKHU IODPPDEOH PDWHULDO
'R DOO ZRUN LQ DQ DUHD WKDW LV ZHOO YHQWLODWHG WR FDUU\ WR[LF
IURP DUHD $OORZ IXPHV WR GLVSHUVH DW OHDVW PLQXWHV
IXPHV DQG GXVW DZD\
EHIRUH ZHOGLQJ RU KHDWLQJ
'R QRW XVH D FKORULQDWHG VROYHQW LQ DUHDV ZKHUH ZHOGLQJ 'LVSRVH RI SDLQW DQG VROYHQW SURSHUO\
ZLOO WDNH SODFH
';3$,17 -8/
31
6DIHW\
76 ²81²$35
';6,*16 $8*
76 ²81²0$<
';3$5. -81
31
6DIHW\
76 ²81²$8*
';6(59 )(%
31
6DIHW\
76 ²81²$8*
H[FHHG / TXDUWV
*HW PHGLFDO DWWHQWLRQ LPPHGLDWHO\
';32,621 $35
76 ²81²$35
'R QRW FKDUJH D IUR]HQ EDWWHU\ LW PD\ H[SORGH :DUP
EDWWHU\ WR & )
';63$5.6 0$5
31
6DIHW\
76 ²81²0$5
SUHVVXUH VSUD\ LQMHFWHG LQWR WKH VNLQ PXVW EH VXUJLFDOO\
UHPRYHG ZLWKLQ D IHZ KRXUV RU JDQJUHQH PD\ UHVXOW
'RFWRUV XQIDPLOLDU ZLWK WKLV W\SH RI LQMXU\ VKRXOG UHIHUHQFH
D NQRZOHGJHDEOH PHGLFDO VRXUFH 6XFK LQIRUPDWLRQ LV
DYDLODEOH IURP 'HHUH &RPSDQ\ 0HGLFDO 'HSDUWPHQW LQ
0ROLQH ,OOLQRLV 86$
';635$< $35
76 ²81²$8*
';12,6( 0$5
31
6DIHW\
76 ²81²$8*
OHJDO XVH RI DJULFXOWXUDO FKHPLFDOV
5HGXFH ULVN RI H[SRVXUH DQG LQMXU\
:HDU DSSURSULDWH SHUVRQDO SURWHFWLYH HTXLSPHQW DV
UHFRPPHQGHG E\ WKH PDQXIDFWXUHU 6HH µ+DQGOH
DJULFXOWXUDO FKHPLFDOV VDIHO\¶ IRXQG LQ WKH 6DIHW\
6HFWLRQ
)LOO IOXVK FDOLEUDWH DQG GHFRQWDPLQDWH VSUD\HU LQ DQ
DUHD ZKHUH UXQRII ZLOO QRW UHDFK SRQGV ODNHV RU VWUHDPV
OLYHVWRFN DUHDV RU JDUGHQV RU QHDU RWKHU SHRSOH
.HHS FKLOGUHQ DZD\ IURP WKH FKHPLFDOV FKHPLFDO
VROXWLRQV DQG ULQVDWHV
,I VSUD\ RU FKHPLFDO FRQFHQWUDWH FRQWDFWV VNLQ KDQGV
RU IDFH ZDVK LPPHGLDWHO\ ZLWK VRDS DQG ZDWHU
76 ²81²$35
,I VSUD\ RU FKHPLFDO FRQFHQWUDWH JHWV LQWR H\HV IOXVK
LPPHGLDWHO\ ZLWK ZDWHU
,I QR]]OH FORJV RU V\VWHP PDOIXQFWLRQV VWRS HQJLQH DQG
UHOLHYH VSUD\ SUHVVXUH IURP V\VWHP
'R QRW SODFH QR]]OH WLSV RU RWKHU FRPSRQHQWV WR WKH
PRXWK WR FOHDU REVWUXFWLRQV .HHS VSDUH WLSV RQ KDQG
IRU UHSODFHPHQW
0LQLPL]H ULVN RI VSUD\ GULIW
3URSHUO\ GLVSRVH RI XQXVHG FKHPLFDOV IOXVKLQJ VROXWLRQ
8VH ODUJH QR]]OH WLSV RSHUDWHG DW ORZHU SUHVVXUHV DQG HPSW\ FKHPLFDO FRQWDLQHUV
'R QRW RSHUDWH VROXWLRQ GHOLYHU\ V\VWHP DW SUHVVXUHV
H[FHHGLQJ N3D EDU SVL
'HFRQWDPLQDWH HTXLSPHQW XVHG LQ PL[LQJ WUDQVIHUULQJ
DQG DSSO\LQJ FKHPLFDOV DIWHU XVH
'R QRW VSUD\ ZKHQ ZLQGV H[FHHG NPK PSK
'R QRW VSUD\ ZKHQ ZLQG LV EORZLQJ WRZDUGV D QHDUE\
VHQVLWLYH FURS JDUGHQ RU SRSXODWHG DUHD
';::&+(0 $35
';5&$3 -81
31
6DIHW\
76 ²81²$8*
VKRUWV DQG HQWDQJOHPHQW LQ PRYLQJ SDUWV
';/226( -81
76 ²81²$8*
:HDU FORVHILWWLQJ FORWKLQJ 6WRS WKH HQJLQH DQG EH VXUH
WKDW DOO URWDWLQJ SDUWV DQG GULYHOLQHV DUH VWRSSHG EHIRUH
PDNLQJ DGMXVWPHQWV FRQQHFWLRQV RU SHUIRUPLQJ DQ\ W\SH
RI VHUYLFH RQ HQJLQH RU PDFKLQH GULYHQ HTXLSPHQW
';527$7,1* $8*
76 ²81²$8*
'R QRW VXSSRUW WKH PDFKLQH RQ FLQGHU EORFNV KROORZ WLOHV
RU SURSV WKDW PD\ FUXPEOH XQGHU FRQWLQXRXV ORDG 'R QRW
ZRUN XQGHU D PDFKLQH WKDW LV VXSSRUWHG VROHO\ E\ D MDFN
)ROORZ UHFRPPHQGHG SURFHGXUHV LQ WKLV PDQXDO
:KHQ LPSOHPHQWV RU DWWDFKPHQWV DUH XVHG ZLWK D
PDFKLQH DOZD\V IROORZ VDIHW\ SUHFDXWLRQV OLVWHG LQ WKH
LPSOHPHQW RU DWWDFKPHQW RSHUDWRU
V PDQXDO
';/2:(5 )(%
31
6DIHW\
76 ²²6(3
&$87,21 VDIHW\ VLJQV &$87,21 DOVR FDOOV DWWHQWLRQ WR
VDIHW\ PHVVDJHV LQ WKLV PDQXDO
';6,*1$/ 0$5
76 ²81²$8*
';/,)7 -81
76 ²81²129
)RU ORRVHQLQJ DQG WLJKWHQLQJ KDUGZDUH XVH WKH FRUUHFW
VL]H WRROV '2 127 XVH 86 PHDVXUHPHQW WRROV RQ
PHWULF IDVWHQHUV $YRLG ERGLO\ LQMXU\ FDXVHG E\ VOLSSLQJ
ZUHQFKHV
8VH RQO\ VHUYLFH SDUWV PHHWLQJ -RKQ 'HHUH VSHFLILFDWLRQV
';5(3$,5 )(%
';::02817 2&7
31
6DIHW\
76 ²81²$35
';:($5 0$5
7(- ²81²2&7
5HDG DOO LQVWUXFWLRQV WKRURXJKO\ GR QRW DWWHPSW
VKRUWFXWV
';&/($1 -81
76 ²81²$35
GRRUV DQG JHW RXWVLGH DLU LQWR WKH DUHD
';$,5 )(%
31
)XHOV /XEULFDQWV DQG &RRODQW
'LHVHO )XHO
&RQVXOW \RXU ORFDO IXHO GLVWULEXWRU IRU SURSHUWLHV RI WKH
6XOIXU &RQWHQW IRU 7LHU DQG 6WDJH ,,, $ (QJLQHV
GLHVHO IXHO DYDLODEOH LQ \RXU DUHD
,Q JHQHUDO GLHVHO IXHOV DUH EOHQGHG WR VDWLVI\ WKH ORZ 8VH RI GLHVHO IXHO ZLWK VXOIXU FRQWHQW OHVV WKDQ
WHPSHUDWXUH UHTXLUHPHQWV RI WKH JHRJUDSKLFDO DUHD LQ PJNJ SSP LV 5(&200(1'('
ZKLFK WKH\ DUH PDUNHWHG 8VH RI GLHVHO IXHO ZLWK VXOIXU FRQWHQW ² PJNJ
² SSP 5('8&(6 WKH RLO DQG ILOWHU FKDQJH
'LHVHO IXHOV VSHFLILHG WR (1 RU $670 ' DUH LQWHUYDO
UHFRPPHQGHG 5HQHZDEOH GLHVHO IXHO SURGXFHG E\
K\GURWUHDWLQJ DQLPDO IDWV DQG YHJHWDEOH RLOV LV EDVLFDOO\ %()25( XVLQJ GLHVHO IXHO ZLWK VXOIXU FRQWHQW JUHDWHU
LGHQWLFDO WR SHWUROHXP GLHVHO IXHO 5HQHZDEOH GLHVHO WKDW WKDQ PJNJ SSP FRQWDFW \RXU -RKQ 'HHUH
PHHWV (1 RU $670 ' LV DFFHSWDEOH IRU XVH DW DOO GHDOHU
SHUFHQWDJH PL[WXUH OHYHOV 6XOIXU &RQWHQW IRU 7LHU DQG 6WDJH ,, (QJLQHV
5HTXLUHG )XHO 3URSHUWLHV 8VH RI GLHVHO IXHO ZLWK VXOIXU FRQWHQW OHVV WKDQ
,Q DOO FDVHV WKH IXHO VKDOO PHHW WKH IROORZLQJ SURSHUWLHV PJNJ SSP LV 5(&200(1'('
8VH RI GLHVHO IXHO ZLWK VXOIXU FRQWHQW ² PJNJ
&HWDQH QXPEHU RI PLQLPXP &HWDQH QXPEHU JUHDWHU ² SSP 5('8&(6 WKH RLO DQG ILOWHU FKDQJH
WKDQ LV SUHIHUUHG HVSHFLDOO\ IRU WHPSHUDWXUHV EHORZ LQWHUYDO
± & ± ) RU HOHYDWLRQV DERYH P IW %()25( XVLQJ GLHVHO IXHO ZLWK VXOIXU FRQWHQW JUHDWHU
WKDQ PJNJ SSP FRQWDFW \RXU -RKQ 'HHUH
&ROG )LOWHU 3OXJJLQJ 3RLQW &)33 VKRXOG EH DW OHDVW GHDOHU
& ) EHORZ WKH H[SHFWHG ORZHVW WHPSHUDWXUH RU &ORXG
3RLQW EHORZ WKH H[SHFWHG ORZHVW DPELHQW WHPSHUDWXUH 6XOIXU &RQWHQW IRU 2WKHU (QJLQHV
)XHO OXEULFLW\ VKRXOG SDVV D PD[LPXP VFDU GLDPHWHU RI 8VH RI GLHVHO IXHO ZLWK VXOIXU FRQWHQW OHVV WKDQ
PP DV PHDVXUHG E\ $670 ' RU ,62 PJNJ SSP LV 5(&200(1'('
$ PD[LPXP VFDU GLDPHWHU RI PP LV SUHIHUUHG 8VH RI GLHVHO IXHO ZLWK VXOIXU FRQWHQW JUHDWHU WKDQ
PJNJ SSP 5('8&(6 WKH RLO DQG ILOWHU FKDQJH
'LHVHO IXHO TXDOLW\ DQG VXOIXU FRQWHQW PXVW FRPSO\ ZLWK
LQWHUYDO
DOO H[LVWLQJ HPLVVLRQV UHJXODWLRQV IRU WKH DUHD LQ ZKLFK
WKH HQJLQH RSHUDWHV '2 127 XVH GLHVHO IXHO ZLWK VXOIXU ,03257$17 'R QRW PL[ XVHG GLHVHO HQJLQH RLO RU DQ\
FRQWHQW JUHDWHU WKDQ PJNJ SSP RWKHU W\SH RI OXEULFDWLQJ RLO ZLWK GLHVHO IXHO
6XOIXU FRQWHQW IRU ,QWHULP 7LHU )LQDO 7LHU ,PSURSHU IXHO DGGLWLYH XVDJH PD\ FDXVH GDPDJH
6WDJH ,,, % DQG 6WDJH ,9 (QJLQHV RQ IXHO LQMHFWLRQ HTXLSPHQW RI GLHVHO HQJLQHV
8VH 21/< XOWUD ORZ VXOIXU GLHVHO 8/6' IXHO ZLWK D
PD[LPXP RI PJNJ SSP VXOIXU FRQWHQW
';)8(/ -81
&$87,21 5HGXFH WKH ULVN RI ILUH +DQGOH IXHO :KHQ XVLQJ %LR'LHVHO IXHO WKH IXHO ILOWHU PD\ UHTXLUH PRUH
FDUHIXOO\ '2 127 ILOO WKH IXHO WDQN ZKHQ HQJLQH IUHTXHQW UHSODFHPHQW GXH WR SUHPDWXUH SOXJJLQJ
LV UXQQLQJ '2 127 VPRNH ZKLOH \RX ILOO WKH
&KHFN HQJLQH RLO OHYHO GDLO\ SULRU WR VWDUWLQJ HQJLQH $
IXHO WDQN RU VHUYLFH WKH IXHO V\VWHP
ULVLQJ RLO OHYHO PD\ LQGLFDWH IXHO GLOXWLRQ RI WKH HQJLQH RLO
)LOO WKH IXHO WDQN DW WKH HQG RI HDFK GD\
V RSHUDWLRQ WR ,03257$17 7KH IXHO WDQN LV YHQWHG WKURXJK WKH
SUHYHQW ZDWHU FRQGHQVDWLRQ DQG IUHH]LQJ GXULQJ FROG ILOOHU FDS ,I D QHZ ILOOHU FDS LV UHTXLUHG DOZD\V
ZHDWKHU UHSODFH LW ZLWK DQ RULJLQDO YHQWHG FDS
.HHS DOO VWRUDJH WDQNV DV IXOO DV SUDFWLFDEOH WR PLQLPL]H
:KHQ IXHO LV VWRUHG IRU DQ H[WHQGHG SHULRG RU LI WKHUH LV D
FRQGHQVDWLRQ
VORZ WXUQRYHU RI IXHO DGG D IXHO FRQGLWLRQHU WR VWDELOL]H WKH
(QVXUH WKDW DOO IXHO WDQN FDSV DQG FRYHUV DUH LQVWDOOHG IXHO DQG SUHYHQW ZDWHU FRQGHQVDWLRQ &RQWDFW \RXU IXHO
SURSHUO\ WR SUHYHQW PRLVWXUH IURP HQWHULQJ 0RQLWRU ZDWHU VXSSOLHU RU -RKQ 'HHUH GHDOHU IRU UHFRPPHQGDWLRQV
FRQWHQW RI WKH IXHO UHJXODUO\
';)8(/ )(%
31
)XHOV /XEULFDQWV DQG &RRODQW
'LHVHO (QJLQH %UHDN,Q 2LO ² 1RQ(PLVVLRQV &HUWLILHG DQG &HUWLILHG 7LHU 7LHU 7LHU
6WDJH , 6WDJH ,, DQG 6WDJH ,,,
1HZ HQJLQHV DUH ILOOHG DW WKH IDFWRU\ ZLWK HLWKHU -RKQ $3, 6HUYLFH &ODVVLILFDWLRQ &&
'HHUH %UHDN,Q RU -RKQ 'HHUH %UHDN,Q 3OXV $&($ 2LO 6HTXHQFH (
(QJLQH 2LO 'XULQJ WKH EUHDNLQ SHULRG DGG -RKQ 'HHUH $&($ 2LO 6HTXHQFH (
%UHDN,Q RU %UHDN,Q 3OXV (QJLQH 2LO UHVSHFWLYHO\ DV
QHHGHG WR PDLQWDLQ WKH VSHFLILHG RLO OHYHO ,03257$17 'R QRW XVH 3OXV ,, 3OXV RU
HQJLQH RLOV PHHWLQJ DQ\ RI WKH IROORZLQJ IRU WKH
2SHUDWH WKH HQJLQH XQGHU YDULRXV FRQGLWLRQV SDUWLFXODUO\ LQLWLDO EUHDNLQ RI D QHZ RU UHEXLOW HQJLQH
KHDY\ ORDGV ZLWK PLQLPDO LGOLQJ WR KHOS VHDW HQJLQH $3, &- $&($ (
FRPSRQHQWV SURSHUO\
$3, &, 3/86 $&($ (
,I -RKQ 'HHUH %UHDN,Q (QJLQH 2LO LV XVHG GXULQJ WKH $3, &, $&($ (
LQLWLDO RSHUDWLRQ RI D QHZ RU UHEXLOW HQJLQH FKDQJH WKH RLO $3, &+ $&($ (
DQG ILOWHU DW D PD[LPXP RI KRXUV
$3, &* $&($ (
,I -RKQ 'HHUH %UHDN,Q 3OXV (QJLQH 2LO LV XVHG FKDQJH $3, &) $&($ (
WKH RLO DQG ILOWHU DW D PLQLPXP RI KRXUV DQG D $3, &)
PD[LPXP HTXDO WR WKH LQWHUYDO VSHFLILHG IRU -RKQ 'HHUH $3, &)
3OXV ,, RU 3OXV RLO
$IWHU HQJLQH RYHUKDXO ILOO WKH HQJLQH ZLWK HLWKHU -RKQ 7KHVH RLOV GR QRW DOORZ WKH HQJLQH WR
'HHUH %UHDN,Q RU %UHDN,Q 3OXV (QJLQH 2LO EUHDN LQ SURSHUO\
,I -RKQ 'HHUH %UHDN,Q RU %UHDN,Q 3OXV (QJLQH 2LO LV -RKQ 'HHUH %UHDN,Q 3OXV (QJLQH 2LO FDQ EH XVHG IRU
QRW DYDLODEOH XVH DQ 6$( : YLVFRVLW\ JUDGH GLHVHO DOO -RKQ 'HHUH GLHVHO HQJLQHV DW DOO HPLVVLRQ FHUWLILFDWLRQ
HQJLQH RLO PHHWLQJ RQH RI WKH IROORZLQJ DQG FKDQJH WKH RLO OHYHOV
DQG ILOWHU DW D PD[LPXP RI KRXUV RI RSHUDWLRQ
$IWHU WKH EUHDNLQ SHULRG XVH -RKQ 'HHUH 3OXV
$3, 6HUYLFH &ODVVLILFDWLRQ &( ,, -RKQ 'HHUH 3OXV RU RWKHU GLHVHO HQJLQH RLO DV
$3, 6HUYLFH &ODVVLILFDWLRQ &' UHFRPPHQGHG LQ WKLV PDQXDO
%UHDN,Q LV D WUDGHPDUN RI 'HHUH &RPSDQ\
%UHDN,Q 3OXV LV D WUDGHPDUN RI 'HHUH &RPSDQ\
3OXV LV D WUDGHPDUN RI 'HHUH &RPSDQ\
';(12,/ 0$<
31
)XHOV /XEULFDQWV DQG &RRODQW
'LHVHO (QJLQH 2LO ² 1RQ(PLVVLRQV &HUWLILHG DQG &HUWLILHG 7LHU DQG 6WDJH ,
8VH RLO YLVFRVLW\ EDVHG RQ WKH H[SHFWHG DLU WHPSHUDWXUH
50 o C 122o F
UDQJH GXULQJ WKH SHULRG EHWZHHQ RLO FKDQJHV
-RKQ 'HHUH 3OXV ,, RLO LV SUHIHUUHG 40 o C 104o F
SAE 40
-RKQ 'HHUH 3OXV LV DOVR UHFRPPHQGHG 30 o C 86 o F
SAE-15W-40
SAE 30
2WKHU RLOV PD\ EH XVHG LI WKH\ PHHW RQH RU PRUH RI WKH
SAE 10W-40
IROORZLQJ 20 o C 68 o F
SAE 10W-30
-RKQ 'HHUH 7RUT*DUG
SAE 5W-30
SAE 0W-40
10 o C 50 o F
$3, 6HUYLFH &DWHJRU\ &-
$3, 6HUYLFH &DWHJRU\ &, 3/86 0o C 32 o F
$3, 6HUYLFH &DWHJRU\ &,
$3, 6HUYLFH &DWHJRU\ &+ -10 o C 14 o F
$3, 6HUYLFH &DWHJRU\ &*
$3, 6HUYLFH &DWHJRU\ &) -20 o C -4 o F
$&($ 2LO 6HTXHQFH (
76 ²81²-8/
$&($ 2LO 6HTXHQFH ( -30 o C -22 o F
$&($ 2LO 6HTXHQFH (
$&($ 2LO 6HTXHQFH (
$&($ 2LO 6HTXHQFH ( -40 o C -40 o F
/XEULFDQW 6WRUDJH
0L[LQJ RI /XEULFDQWV
31
)XHOV /XEULFDQWV DQG &RRODQW
-RKQ 'HHUH &22/*$5' ,, &RQFHQWUDWH LQ D ² :KHQ &22/*$5' ,, RU &22/*$5' ,, 3* LV XVHG WKH
PL[WXUH RI FRQFHQWUDWH ZLWK TXDOLW\ ZDWHU GUDLQ LQWHUYDO LV \HDUV RU KRXUV RI RSHUDWLRQ
,03257$17 :KHQ PL[LQJ FRRODQW FRQFHQWUDWH ZLWK ,I D FRRODQW RWKHU WKDQ &22/*$5' ,, RU &22/*$5' ,,
ZDWHU GR QRW XVH OHVV WKDQ RU JUHDWHU 3* LV XVHG UHGXFH WKH GUDLQ LQWHUYDO WR \HDUV RU
WKDQ FRQFHQWUDWLRQ RI FRRODQW /HVV WKDQ KRXUV RI RSHUDWLRQ
JLYHV LQDGHTXDWH DGGLWLYHV IRU FRUURVLRQ ,03257$17 'R QRW XVH FRROLQJ V\VWHP VHDOLQJ
SURWHFWLRQ *UHDWHU WKDQ FDQ UHVXOW LQ DGGLWLYHV RU DQWLIUHH]H WKDW FRQWDLQV
FRRODQW JHODWLRQ DQG FRROLQJ V\VWHP SUREOHPV VHDOLQJ DGGLWLYHV
2WKHU &RRODQWV 'R QRW PL[ HWK\OHQH JO\FRO DQG SURS\OHQH
JO\FRO EDVH FRRODQWV
2WKHU HWK\OHQH JO\FRO RU SURS\OHQH JO\FRO EDVH FRRODQWV
PD\ EH XVHG LI WKH\ PHHW WKH IROORZLQJ VSHFLILFDWLRQ 'R QRW XVH FRRODQWV WKDW FRQWDLQ QLWULWHV
31
)XHOV /XEULFDQWV DQG &RRODQW
31
2SHUDWLQJ WKH (QJLQH
8VLQJ 'LDJQRVWLF *DXJH WR $FFHVV (QJLQH ,QIRUPDWLRQ 2SWLRQDO HTXLSPHQW
5* ²81²6(3
'LDJQRVWLF *DXJH
$²'LDJQRVWLF *DXJH '²(QWHU .H\ )² $PEHU ´:$51,1*´ ,QGLFDWRU
%²0HQX .H\ (²5HG ´6723 (1*,1(´ /LJKW
&²$UURZ .H\V ,QGLFDWRU /LJKW
3UHVV WKH PHQX NH\ % WR DFFHVV WKH YDULRXV HQJLQH 7KH GLDJQRVWLF JDXJH LQFOXGHV D JUDSKLFDO EDFNOLW /LTXLG
IXQFWLRQV LQ VHTXHQFH 7KH GLVSOD\V FDQ EH VHOHFWHG DV &U\VWDO 'LVSOD\ /&' VFUHHQ 7KH GLVSOD\ FDQ VKRZ
HLWKHU FXVWRPDU\ (QJOLVK RU PHWULF XQLWV 7KH IROORZLQJ HLWKHU D VLQJOH SDUDPHWHU RU D TXDGUDQW GLVSOD\ VKRZLQJ
PHQX RI HQJLQH SDUDPHWHUV FDQ EH GLVSOD\HG RQ WKH IRXU SDUDPHWHUV VLPXOWDQHRXVO\ 7KH GLDJQRVWLF JDXJH
GLDJQRVWLF JDXJH ZLQGRZ XVHV WZR DUURZ NH\V & IRU VFUROOLQJ WKURXJK WKH HQJLQH
SDUDPHWHU OLVW DQG YLHZLQJ WKH PHQX OLVW DQG DQ HQWHU NH\
(QJLQH KRXUV ' IRU VHOHFWLQJ KLJKOLJKWHG LWHPV 7KH UHG ( DQG DPEHU
(QJLQH USP ) OLJKWV DUH XVHG WR VLJQDO DFWLYH WURXEOH FRGH UHFHLYHG
6\VWHP YROWDJH E\ WKH GLDJQRVWLF JDXJH
3HUFHQW HQJLQH ORDG DW WKH FXUUHQW USP
&'% -$1
31
2SHUDWLQJ WKH (QJLQH
5* ²81²2&7
0HQX 'LVSOD\
285*3$ 6(3
5* ²81²2&7
0DLQ 0HQX ,WHPV
285*3$ 6(3
5* ²81²6(3
31
2SHUDWLQJ WKH (QJLQH
5* ²81²2&7
UHWXUQ WR WKH HQJLQH SDUDPHWHU GLVSOD\
285*3$ 6(3
5* ²81²6(3
RQO\ IXQFWLRQ
31
2SHUDWLQJ WKH (QJLQH
5* ²81²2&7
(QWHU .H\
285*3$% 6(3
5* ²81²6(3
8VH $UURZ .H\V 7R 6FUROO
285*3$% 6(3
5* ²81²6(3
31
2SHUDWLQJ WKH (QJLQH
3UHVV WKH 0HQX NH\ WR H[LW WKH PDLQ PHQX DQG UHWXUQ
WR WKH HQJLQH SDUDPHWHU GLVSOD\
5* ²81²6(3
([LW 0DLQ 0HQX
285*3$% 6(3
5* ²81²6(3
QDYLJDWH WKH GLDJQRVWLF JDXJH VFUHHQV ,I HQJLQH
VWDUW XS LV GHVLUHG 6HH 6WDUWLQJ 7KH (QJLQH $OO
RI WKH HQJLQH YDOXHV LOOXVWUDWHG RQ WKH GLDJQRVWLF
JDXJH LQGLFDWH WKH HQJLQH LV UXQQLQJ
)RU GHVFULSWLRQ RI WURXEOH FRGHV VHH FKDUW
LQ 7URXEOHVKRRWLQJ 6HFWLRQ
0HQX .H\
5* ²81²2&7
6HOHFW 6WRUHG &RGHV
31
2SHUDWLQJ WKH (QJLQH
5* ²81²2&7
(QWHU .H\
285*3$& 6(3
5* ²81²2&7
8VH $UURZ .H\V 7R 6FUROO
285*3$& 6(3
5* ²81²2&7
31
2SHUDWLQJ WKH (QJLQH
3UHVV WKH 0HQX NH\ WR H[LW WKH PDLQ PHQX DQG UHWXUQ
WR WKH HQJLQH SDUDPHWHU GLVSOD\
5* ²81²6(3
([LW 0DLQ 0HQX
285*3$& 6(3
5* ²81²6(3
127( 7KH HQJLQH GRHV QRW QHHG WR EH UXQQLQJ WR
QDYLJDWH WKH GLDJQRVWLF JDXJH VFUHHQV ,I HQJLQH
VWDUW XS LV GHVLUHG 6HH 6WDUWLQJ 7KH (QJLQH $OO
RI WKH HQJLQH YDOXHV LOOXVWUDWHG RQ WKH GLDJQRVWLF
JDXJH LQGLFDWH WKH HQJLQH LV UXQQLQJ
)RU GHVFULSWLRQ RI WURXEOH FRGHV VHH FKDUW
LQ 7URXEOHVKRRWLQJ 6HFWLRQ 1RUPDO 2SHUDWLRQ
5* ²81²6(3
FRUUHFWLYH DFWLRQ QHHGHG
,03257$17 ,JQRULQJ DFWLYH WURXEOH FRGHV FDQ
UHVXOW LQ VHYHUH HQJLQH GDPDJH
285*3$' 6(3
31
2SHUDWLQJ WKH (QJLQH
5* ²81²6(3
+LGH 7URXEOH &RGHV
285*3$' 6(3
5* ²81²6(3
3UHVVLQJ WKH (QWHU NH\ ZLOO UHGLVSOD\ WKH KLGGHQ
WURXEOH FRGH
285*3$' 6(3
5* ²81²6(3
SDUDPHWHU GLVSOD\
(QWHU .H\
285*3$' 6(3
FRUUHFWHG
285*3$' 6(3
31
2SHUDWLQJ WKH (QJLQH
5* ²81²6(3
'XULQJ QRUPDO RSHUDWLRQ WKH VLQJOH RU IRXU SDUDPHWHU
VFUHHQ ZLOO EH GLVSOD\HG
1RUPDO 2SHUDWLRQ
285*3$( 6(3
5* ²81²6(3
FRUUHFWLYH DFWLRQ QHHGHG
,I WKH ZRUG 1H[W DSSHDUV DERYH WKH DUURZ NH\V WKHUH
DUH PRUH WURXEOH FRGHV WKDW FDQ EH YLHZHG E\ XVLQJ
WKH DUURZ NH\V WR VFUROO WR WKH QH[W WURXEOH FRGH
6KXWGRZQ 0HVVDJH
285*3$( 6(3
5* ²81²6(3
+LGH 7URXEOH &RGH
285*3$( 6(3
31
2SHUDWLQJ WKH (QJLQH
5* ²81²6(3
5HGLVSOD\ 7URXEOH &RGH
285*3$( 6(3
5* ²81²6(3
VKXWGRZQ LFRQ XQWLO WKH WURXEOH FRGH FRQGLWLRQ LV
FRUUHFWHG
,03257$17 ,JQRULQJ WKH VKXWGRZQ PHVVDJH FDQ
UHVXOW LQ VHYHUH HQJLQH GDPDJH
6KXWGRZQ ,FRQ
285*3$( 6(3
$GMXVWLQJ %DFNOLJKWLQJ
7XUQ WKH NH\ VZLWFK WR WKH 21 SRVLWLRQ 6WDUWLQJ DW
5* ²81²6(3
WKH VLQJOH RU IRXU HQJLQH SDUDPHWHU GLVSOD\ SUHVV WKH
0HQX NH\
0HQX .H\
285*3 2&7
31
2SHUDWLQJ WKH (QJLQH
5* ²81²2&7
3UHVV (QWHU .H\
285*3 2&7
5* ²81²6(3
$GMXVW %DFNOLJKW ,QWHQVLW\
285*3 2&7
5* ²81²6(3
31
2SHUDWLQJ WKH (QJLQH
3UHVV WKH 0HQX NH\ WR H[LW WKH PDLQ PHQX DQG UHWXUQ
WR WKH HQJLQH SDUDPHWHU GLVSOD\
5* ²81²6(3
([LW 0DLQ 0HQX
285*3 2&7
$GMXVWLQJ &RQWUDVW
7XUQ WKH NH\ VZLWFK WR WKH 21 SRVLWLRQ 6WDUWLQJ DW
5* ²81²6(3
WKH VLQJOH RU IRXU HQJLQH SDUDPHWHU GLVSOD\ SUHVV WKH
0HQX NH\
0HQX .H\
285*3$) 6(3
5* ²81²2&7
6HOHFW $GMXVW &RQWUDVW
285*3$) 6(3
31
2SHUDWLQJ WKH (QJLQH
5* ²81²6(3
$GMXVW &RQWUDVW ,QWHQVLW\
285*3$) 6(3
5* ²81²6(3
5HWXUQ 7R 0DLQ 0HQX
285*3$) 6(3
3UHVV WKH 0HQX NH\ WR H[LW WKH PDLQ PHQX DQG UHWXUQ
WR WKH HQJLQH SDUDPHWHU GLVSOD\
5* ²81²6(3
285*3$) 6(3
0HQX .H\
31
2SHUDWLQJ WKH (QJLQH
5* ²81²2&7
6HOHFW 8QLWV
285*3% 6(3
5* ²81²2&7
3UHVV (QWHU .H\
285*3% 6(3
5* ²81²6(3
0HWULF N3D DQG 0HWULF EDU DUH IRU ,6 XQLWV ZLWK
SUHVVXUHV GLVSOD\HG LQ N3D DQG EDU UHVSHFWLYHO\ DQG
WHPSHUDWXUHV LQ &
8VH WKH $UURZ NH\V WR KLJKOLJKW WKH GHVLUHG XQLWV RI
PHDVXUHPHQW
31
2SHUDWLQJ WKH (QJLQH
5* ²81²6(3
3UHVV (QWHU .H\ WR 6HOHFW
285*3% 6(3
5* ²81²6(3
5HWXUQ 7R 0DLQ 0HQX
285*3% 6(3
5* ²81²6(3
285*3% 6(3
0HQX .H\
31
2SHUDWLQJ WKH (QJLQH
5* ²81²2&7
6HWXS 8S 'LVSOD\
285*3% 6(3
5* ²81²2&7
3UHVV (QWHU .H\
285*3% 6(3
5* ²81²6(3
7HPSHUDWXUH DQG 2LO 3UHVVXUH
E &XVWRP 6HWXS ± 7KLV RSWLRQ FRQWDLQV D OLVW RI
HQJLQH SDUDPHWHUV (QJLQH SDUDPHWHUV IURP WKLV
OLVW FDQ EH VHOHFWHG WR UHSODFH DQ\ RU DOO RI WKH
GHIDXOW SDUDPHWHUV 7KLV RSWLRQ FDQ EH XVHG WR
DGG SDUDPHWHUV DYDLODEOH IRU VFUROOLQJ LQ WKH 8S
'LVSOD\ 8S 'LVSOD\ 2SWLRQV
31
2SHUDWLQJ WKH (QJLQH
5* ²81²6(3
6HOHFW 'HIDXOWV
285*3% 6(3
5* ²81²6(3
'HIDXOWV 6HOHFWHG
285*3% 6(3
5* ²81²6(3
5HVWRUHG 7R 'HIDXOWV
31
2SHUDWLQJ WKH (QJLQH
5* ²81²6(3
6HOHFW &XVWRP 6HWXS
285*3% 6(3
5* ²81²6(3
(QJLQH 3DUDPHWHUV
285*3% 6(3
5* ²81²6(3
6HOHFW 3DUDPHWHUV
31
2SHUDWLQJ WKH (QJLQH
5* ²81²6(3
'HVHOHFW 3DUDPHWHUV
285*3% 6(3
8VH WKH $UURZ NH\V WR VFUROO DQG KLJKOLJKW WKH GHVLUHG
SDUDPHWHU WKDW KDV QRW EHHQ VHOHFWHG IRU GLVSOD\
SDUDPHWHU ZLWKRXW D QXPEHU WR ULJKW RI LW
5* ²81²6(3
6HOHFW 'HVLUHG 3DUDPHWHUV
285*3% 6(3
5* ²81²6(3
31
2SHUDWLQJ WKH (QJLQH
5* ²81²6(3
$XWRPDWLF 6FDQ 2II
285*3% 6(3
5* ²81²6(3
$XWRPDWLF 6FDQ 2Q
285*3% 6(3
5* ²81²6(3
31
2SHUDWLQJ WKH (QJLQH
5* ²81²6(3
0HQX .H\
285*3% 6(3
3UHVV WKH 0HQX NH\ WR H[LW WKH PDLQ PHQX DQG UHWXUQ
WR WKH HQJLQH SDUDPHWHU GLVSOD\
5* ²81²6(3
([LW 0DLQ 0HQX
285*3% 6(3
5* ²81²6(3
RU IRXU HQJLQH SDUDPHWHU GLVSOD\ SUHVV WKH 0HQX NH\
0HQX .H\
285*3% 6(3
31
2SHUDWLQJ WKH (QJLQH
5* ²81²2&7
3UHVV (QWHU .H\
285*3% 6(3
5* ²81²2&7
E &XVWRP 6HWXS ± 7KLV RSWLRQ FRQWDLQV D OLVW RI
HQJLQH SDUDPHWHUV (QJLQH SDUDPHWHUV IURP WKLV OLVW
FDQ EH VHOHFWHG WR UHSODFH DQ\ RU DOO RI WKH GHIDXOW
SDUDPHWHUV
285*3% 6(3
5* ²81²6(3
5HVWRUHG 7R 'HIDXOWV
31
2SHUDWLQJ WKH (QJLQH
5* ²81²6(3
&XVWRP 6HWXS
285*3% 6(3
5* ²81²6(3
6HOHFW 3DUDPHWHUV
285*3% 6(3
5* ²81²6(3
31
2SHUDWLQJ WKH (QJLQH
5* ²81²6(3
'LVSOD\
285*3% 6(3
5* ²81²6(3
(QWHU 6HOHFWHG 3DUDPHWHU
285*3% 6(3
5* ²81²6(3
5HWXUQ 7R 8S &XVWRP 6HWXS
285*3% 6(3
8S 'LVSOD\
31
2SHUDWLQJ WKH (QJLQH
5* ²81²6(3
5HWXUQ 7R 0DLQ 0HQX
285*3% 6(3
3UHVV WKH 0HQX NH\ WR H[LW WKH PDLQ PHQX DQG UHWXUQ
WR WKH HQJLQH SDUDPHWHU GLVSOD\
5* ²81²2&7
6HOHFW 5HPDLQLQJ 3DUDPHWHUV
285*3% 6(3
%UHDNLQ SHULRG
:LWKLQ ILUVW KRXUV RI RSHUDWLRQ $IWHU WKH ILUVW KRXUV GUDLQ WKH FUDQNFDVH DQG FKDQJH
'XULQJ WKH ILUVW KRXUV RI RSHUDWLRQ DYRLG RYHUORDGLQJ WKH RLO ILOWHU VHH &+$1*,1* (1*,1( 2,/ $1' ),/7(5
H[FHVVLYH LGOLQJ DQG QRORDG RSHUDWLRQ )LOO FUDQNFDVH ZLWK VHDVRQDO YLVFRVLW\ JUDGH RLO VHH
',(6(/ (1*,1( 2,/
,I RLO KDV WR EH DGGHG GXULQJ WKLV WLPH VHH (1*,1(
%5($.,1 2,/ &KHFN WHQVLRQ RI DOWHUQDWRU EHOW
127( 'XULQJ WKH EUHDNLQ SHULRG D KLJKHUWKDQXVXDO RLO &KHFN FRQQHFWLRQV RI DLU LQWDNH KRVHV
FRQVXPSWLRQ VKRXOG EH FRQVLGHUHG DV QRUPDO
&KHFN IRU SURSHU WLJKWHQLQJ RI FDS VFUHZV DOO DURXQG WKH
$IWHU ILUVW KRXUV RI RSHUDWLRQ HQJLQH
'36*&' -$1
&$87,21 %HIRUH VWDUWLQJ HQJLQH LQ D FRQILQHG 3HUIRUP DOO SUHVWDUWLQJ FKHFNV RXWOLQHG LQ
EXLOGLQJ LQVWDOO SURSHU RXWOHW H[KDXVW YHQWLODWLRQ 0DLQWHQDQFH'DLO\ 6HFWLRQ
HTXLSPHQW $OZD\V XVH VDIHW\ DSSURYHG
2SHQ WKH IXHO VXSSO\ VKXWRII YDOYH LI HTXLSSHG
IXHO VWRUDJH DQG SLSLQJ
$FWLYDWH WKH VWDUWHU PRWRU VZLWFK WR FUDQN WKH HQJLQH
127( ,I WHPSHUDWXUH LV EHORZ & ) LW PD\ DQG UHOHDVH LW DV VRRQ DV HQJLQH VWDUWV
EH QHFHVVDU\ WR XVH FROG ZHDWKHU VWDUWLQJ DLGV
6HH &2/' :($7+(5 23(5$7,21 127( 'R QRW RSHUDWH WKH VWDUWHU PRWRU PRUH WKDQ
VHFRQGV DW D WLPH
'36*&' -$1
31
2SHUDWLQJ WKH (QJLQH
76 ²81²0$5
&$87,21 '2 127 XVH VWDUWLQJ IOXLG RQ HQJLQHV
HTXLSSHG ZLWK JULGW\SH DLU LQWDNH KHDWHU RU JORZ
SOXJ V (WKHU VWDUWLQJ IOXLG LV KLJKO\ IODPPDEOH
DQG PD\ H[SORGH FDXVLQJ VHULRXV LQMXU\
127( 2Q HQJLQHV ZLWK HOHFWURQLFDOO\ FRQWUROOHG IXHO +DQGOH VWDUWLQJ IOXLG ZLWK FDUH
V\VWHP '( +3&5 WKH DLU LQWDNH KHDWHU
RSHUDWHV DXWRPDWLFDOO\ FRQWUROOHG E\ WKH (&8 $Q
HQJLQH SUHKHDWHU LQGLFDWRU OLJKW FRPHV RQ ZKHQ
WKH NH\ VZLWFK LV WXUQHG 21 ,Q ZDUP ZHDWKHU WKH
OLJKW FRPHV RQ EULHIO\ IRU D OLJKW FKHFN ,Q FROG
ZHDWKHU WKH OLJKW UHPDLQV 21 GXULQJ WKH DXWRPDWLF
RSHUDWLRQ RI WKH DLU LQWDNH KHDWHU RU JORZ SOXJ
V 2SHUDWLQJ WLPH GHSHQGV RQ WHPSHUDWXUH 'R
QRW FUDQN HQJLQH XQWLO OLJKW JRHV 2))
&' ²81²6(3
WKH VLQJOH JORZ SOXJ % VFUHZHG LQ F\OLQGHU KHDG LQWDNH
PDQLIROG $FWLYDWH WKH JORZ SOXJ SUHKHDWHU SRVLWLRQ IRU
VHFRQGV PD[LPXP WKHQ VWDUW WKH HQJLQH
DQG HQJLQHV H[FHSW +3&5 YDOYH KHDG
DUH RSWLRQDOO\ HTXLSSHG ZLWK WKH JULGW\SH DLU KHDWHU $
LQVWDOOHG EHWZHHQ F\OLQGHU KHDG DQG DLU LQWDNH SLSH
)RU PHFKDQLFDO IXHO V\VWHP DFWLYDWH WKH KHDWLQJ *ORZ 3OXJ RU *ULG7\SH DLU KHDWHU
HOHPHQW SUHKHDWHU SRVLWLRQ IRU VHFRQGV PD[LPXP
WKHQ VWDUW WKH HQJLQH
)RU HOHFWURQLFDOO\ FRQWUROOHG HQJLQHV '( +3&5
YDOYH KHDG WXUQ NH\ VZLWFK 21 EXW '2 127 FUDQN
HQJLQH XQWLO HQJLQH SUHKHDWHU LQGLFDWRU OLJKW WXUQV 2))
+3&5 YDOYH KHDG HQJLQHV DUH HTXLSSHG ZLWK JORZ
&' ²81²-$1
SOXJV RQH SHU F\OLQGHU & 7XUQ NH\ VZLWFK 21 EXW
'2 127 FUDQN HQJLQH XQWLO SUHKHDWHU LQGLFDWRU OLJKW
WXUQV 2))
31
2SHUDWLQJ WKH (QJLQH
&RRODQW KHDWHU
&RQQHFW SOXJ RI FRRODQW KHDWHU $ WR D SURSHU SRZHU
VRXUFH RU 9
$W DQ DPELHQW WHPSHUDWXUH RI & ) WKH KHDWLQJ
SURFHVV WDNHV DSSUR[LPDWLYHO\ KRXUV ([WHQG KHDWLQJ
/; ²81²2&7
SHULRG LI DPELHQW WHPSHUDWXUH LV ORZHU
'36*&' )(%
)XHO SUHKHDWHU
)XHO SUHKHDWHU $ VZLWFKHV 21 DQG 2)) DXWRPDWLFDOO\ LQ
UHODWLRQ ZLWK WKH DPELHQW WHPSHUDWXUH
/; ²81²2&7
'36*&' )(%
31
2SHUDWLQJ WKH (QJLQH
76 ²81²$35
.HHS VSDUNV DQG IODPHV DZD\ IURP EDWWHU\
%HIRUH FRQQHFWLQJ RU GLVFRQQHFWLQJ D EDWWHU\
FKDUJHU WXUQ FKDUJHU RII 0DNH ODVW FRQQHFWLRQ
DQG ILUVW GLVFRQQHFWLRQ DW D SRLQW DZD\ IURP
EDWWHU\ $OZD\V FRQQHFW 1(*$7,9( ± FDEOH
ODVW DQG GLVFRQQHFW WKLV FDEOH ILUVW
5* ²81²'(&
YROW ERRVWHU EDWWHU\ IRU YROW HOHFWULFDO
V\VWHPV DQG YROW ERRVWHU EDWWHU\LHV IRU
YROW HOHFWULFDO V\VWHPV
5* ²81²'(&
&RQQHFW RQH HQG RI WKH RWKHU MXPSHU FDEOH WR WKH
1(*$7,9( ± SRVW RI WKH ERRVWHU EDWWHU\
$/:$<6 FRPSOHWH WKH KRRNXS E\ PDNLQJ WKH ODVW
FRQQHFWLRQ RI WKH 1(*$7,9( ± FDEOH WR D JRRG
JURXQG RQ WKH HQJLQH IUDPH DQG DZD\ IURP WKH
EDWWHU\LHV
9ROWV 6\VWHP
6WDUW WKH HQJLQH 'LVFRQQHFW MXPSHU FDEOHV
LPPHGLDWHO\ DIWHU HQJLQH VWDUWV 'LVFRQQHFW
$²9ROW 0DFKLQH EDWWHU\ &²%RRVWHU FDEOH
1(*$7,9( ± FDEOH ILUVW LHV '²&DEOH WR VWDUWHU PRWRU
%²9ROW %RRVWHU EDWWHU\ LHV
'36*&' -$1
31
2SHUDWLQJ WKH (QJLQH
(QJLQH RSHUDWLRQ
:DUPLQJ HQJLQH 8QXVXDO QRLVH RU YLEUDWLRQ
2SHUDWH HQJLQH DW KLJK LGOH IRU WR PLQXWHV EHIRUH ([FHVVLYH EODFN H[KDXVW
DSSO\LQJ WKH ORDG ([FHVVLYH IXHO FRQVXPSWLRQ
127( 7KLV SURFHGXUH GRHV QRW DSSO\ WR VWDQGE\
([FHVVLYH RLO FRQVXPSWLRQ
JHQHUDWRU VHWV ZKHUH WKH HQJLQH LV ORDGHG
)OXLG OHDNV
LPPHGLDWHO\ XSRQ UHDFKLQJ UDWHG VSHHG 5HFRPPHQGDWLRQ IRU WXUERFKDUJHU HQJLQHV
6KRXOG WKH HQJLQH VWDOO ZKHQ RSHUDWLQJ XQGHU ORDG
1RUPDO HQJLQH RSHUDWLRQ ,00(',$7(/< UHVWDUW LW WR SUHYHQW RYHUKHDWLQJ RI
&RPSDUH HQJLQH FRRODQW WHPSHUDWXUH DQG HQJLQH RLO WXUERFKDUJHU FRPSRQHQWV
SUHVVXUH ZLWK VSHFLILFDWLRQV EHORZ
,GOLQJ HQJLQH
6SHFLILFDWLRQ $YRLG H[FHVVLYH HQJLQH LGOLQJ 3URORQJHG LGOLQJ PD\
0LQLPXP RLO SUHVVXUH DW FDXVH WKH HQJLQH FRRODQW WHPSHUDWXUH WR IDOO EHORZ LWV
IXOO ORDG UDWHG VSHHG QRUPDO UDQJH 7KLV LQ WXUQ FDXVHV FUDQNFDVH RLO GLOXWLRQ
²3UHVVXUH N3D EDU SVL GXH WR LQFRPSOHWH IXHO FRPEXVWLRQ DQG SHUPLWV IRUPDWLRQ
&RRODQW WHPSHUDWXUH RI JXPP\ GHSRVLWV RQ YDOYHV SLVWRQV DQG SLVWRQ ULQJV ,W
UDQJH²7HPSHUDWXUH ²& ²) DOVR SURPRWHV UDSLG DFFXPXODWLRQ RI HQJLQH VOXGJH DQG
XQEXUQHG IXHO LQ WKH H[KDXVW V\VWHP ,I DQ HQJLQH ZLOO EH
LGOLQJ IRU PRUH WKDQ PLQXWHV VWRS DQG UHVWDUW ODWHU
6WRS HQJLQH LPPHGLDWHO\ LI FRRODQW WHPSHUDWXUH LV DERYH
RU RLO SUHVVXUH EHORZ VSHFLILFDWLRQV RU LI WKHUH DUH DQ\ 127( *HQHUDWRU VHW DSSOLFDWLRQV KDYH WKH JRYHUQRU
VLJQV RI SDUW IDLOXUH 6\PSWRPV WKDW PD\ EH HDUO\ VLJQV RI ORFNHG DW D VSHFLILHG VSHHG DQG GR QRW KDYH
HQJLQH SUREOHPV FRXOG EH D VORZ LGOH IXQFWLRQ 7KHVH HQJLQHV LGOH DW QR
ORDG JRYHUQHG VSHHG IDVW LGOH
6XGGHQ ORVV RI SRZHU
2LO DW QRUPDO RSHUDWLQJ WHPSHUDWXUH RI & )
'36*&' -$1
31
0DLQWHQDQFH
2EVHUYH VHUYLFH LQWHUYDOV
8VLQJ KRXU PHWHU DV D JXLGH SHUIRUP DOO VHUYLFHV DW WKH ,03257$17 5HFRPPHQGHG VHUYLFH LQWHUYDOV DUH IRU
KRXUO\ LQWHUYDOV LQGLFDWHG RQ IROORZLQJ SDJHV $W HDFK QRUPDO RSHUDWLQJ FRQGLWLRQV 6HUYLFH 025(
VFKHGXOHG PDLQWHQDQFH LQWHUYDO SHUIRUP DOO SUHYLRXV 2)7(1 LI HQJLQH LV RSHUDWHG XQGHU DGYHUVH
PDLQWHQDQFH RSHUDWLRQV LQ DGGLWLRQ WR WKH RQHV VSHFLILHG FRQGLWLRQV 1HJOHFWLQJ PDLQWHQDQFH FDQ UHVXOW
.HHS D UHFRUG RI KRXUO\ LQWHUYDOV DQG VHUYLFHV SHUIRUPHG LQ IDLOXUHV RU SHUPDQHQW GDPDJH WR WKH HQJLQH
XVLQJ FKDUWV SURYLGHG LQ 0DLQWHQDQFH 5HFRUGV 6HFWLRQ
'36*&' -$1
76 ²81²$8*
&RQVXOW \RXU -RKQ 'HHUH HQJLQH GLVWULEXWRU VHUYLFLQJ
GHDOHU RU \RXU QHDUHVW -RKQ 'HHUH 3DUWV 1HWZRUN IRU
UHFRPPHQGHG IXHOV OXEULFDQWV DQG FRRODQW $OVR
DYDLODEOH DUH QHFHVVDU\ DGGLWLYHV IRU XVH ZKHQ RSHUDWLQJ
HQJLQHV LQ WURSLFDO DUFWLF RU DQ\ RWKHU DGYHUVH FRQGLWLRQV
'36*&' -$1
31
0DLQWHQDQFH
D
&OHDQ DLU ILOWHU HOHPHQW ZKHQ UHVWULFWLRQ LQGLFDWRU LV UHG 5HSODFH ILOWHU HOHPHQW DIWHU FOHDQLQJV RU RQFH D \HDU
E
&KDQJH RLO DQG ILOWHU DIWHU WKH ILUVW KRXUV RI RSHUDWLRQ WKHQ HYHU\ KRXUV PD[LPXP WKHUHDIWHU VHH ',(6(/ (1*,1(
2,/ LQIRUPDWLRQ &KDQJH RLO DQG ILOWHU DW OHDVW RQFH D \HDU
F
&KHFN EHOW WHQVLRQ HYHU\ KRXUV RQ DQG HQJLQHV DQG RQ DQG HQJLQHV ZLWK PDQXDO WHQVLRQHU &KHFN
DXWRPDWLF EHOW WHQVLRQHU HYHU\ KRXUV \HDU RQ DQG HQJLQHV ZKHQ HTXLSSHG
G
+DYH \RXU DXWKRUL]HG VHUYLFLQJ GHDOHU RU HQJLQH GLVWULEXWRU DGMXVW YDOYH FOHDUDQFH DV IROORZV $IWHU WKH ILUVW KRXUV RI RSHUDWLRQ WKHQ
HYHU\ KRXUV WKHUHDIWHU RQ DQG HQJLQHV (YHU\ KRXUV RQ DQG HQJLQHV
H
+DYH \RXU DXWKRUL]HG GHDOHU RU HQJLQH GLVWULEXWRU UHSODFH WKH YLEUDWLRQ GDPSHU HYHU\ KRXUV \HDUV
I
'UDLQ DQG IOXVK FRROLQJ V\VWHP HYHU\ KRXUV \HDUV ZKHQ -RKQ 'HHUH &22/*$5' ,, FRRODQW LV XVHG 2WKHUZLVH HYHU\ KRXUV \HDUV
J
&RQWDFW \RXU GHDOHU ZKHQ WKHUPRVWDW RU LQMHFWLRQ QR]]OHV DUH VXVSHFWHG WR EH GHIHFWLYH 5HSODFH LQMHFWLRQ QR]]OHV
HYHU\ KRXUV DQG WKHUPRVWDW HYHU\ KRXUV
'36*&' 0$<
31
0DLQWHQDQFH'DLO\ RU HYHU\ KRXUV
&KHFN (QJLQH 2LO /HYHO
DQG (QJLQHV
&' ²81²6(3
&' ²81²$8*
2LO 'LSVWLFN 2LO )LOOHU &DS
%HIRUH VWDUWLQJ WKH HQJLQH IRU WKH ILUVW WLPH RI WKH GD\
FKHFN HQJLQH RLO OHYHO RQ GLSVWLFN $ $GG RLO DV UHTXLUHG
XVLQJ VHDVRQDO YLVFRVLW\ JUDGH RLO DW URFNHU DUP FRYHU
ILOOHU FDS %
,03257$17 '2 127 ILOO DERYH WKH FURVVKDWFK DUHD
2LO OHYHOV DQ\ZKHUH ZLWKLQ FURVVKDWFK DUHD DUH
)' ²81²0$5
FRQVLGHUHG LQ WKH DFFHSWDEOH RSHUDWLQJ UDQJH
'36*&' 0$<
)' ²81²0$5
&' ²81²129
%HIRUH VWDUWLQJ WKH HQJLQH IRU WKH ILUVW WLPH RI WKH GD\ ,03257$17 '2 127 ILOO DERYH WKH FURVVKDWFK DUHD
FKHFN HQJLQH RLO OHYHO RQ GLSVWLFN $ $GG RLO DV UHTXLUHG 2LO OHYHOV DQ\ZKHUH ZLWKLQ FURVVKDWFK DUHD DUH
XVLQJ VHDVRQDO YLVFRVLW\ JUDGH RLO DW RLO ILOOHU FDS % FRQVLGHUHG LQ WKH DFFHSWDEOH RSHUDWLQJ UDQJH
31
0DLQWHQDQFH'DLO\ RU HYHU\ KRXUV
&' ²81²$35
5HLQVWDOO GLSVWLFN WKHQ WLJKWHQ E\ KDQG
$JDLQ UHPRYH GLSVWLFN DQG FKHFN RLO OHYHO
$GG RLO ZKHQ OHYHO LV EHORZ WKH KROH DUHD % 8VH
VHDVRQDO YLVFRVLW\ JUDGH RLO
,03257$17 '2 127 ILOO DERYH WKH KROH DUHD %
2LO 'LSVWLFN)LOOHU &DS
&' ²81²$35
+ROH $UHD RQ 2LO 'LSVWLFN)LOOHU &DS
'36*&' 0$<
&' ²81²129
76 ²81²$35
5DGLDWRU &DS
$²5DGLDWRU &DS
&$87,21 ([SORVLYH UHOHDVH RI IOXLGV IURP 5HPRYH UDGLDWRU FDS $ DQG FKHFN FRRODQW OHYHO ZKLFK
SUHVVXUL]HG FRROLQJ V\VWHP FDQ FDXVH VKRXOG EH DW ERWWRP RI ILOOHU QHFN )LOO UDGLDWRU ZLWK SURSHU
VHULRXV EXUQV FRRODQW VROXWLRQ LI OHYHO LV ORZ &KHFN HQWLUH FRROLQJ
V\VWHP IRU OHDNV
2QO\ UHPRYH ILOOHU FDS ZKHQ HQJLQH LV FROG RU
ZKHQ FRRO HQRXJK WR WRXFK ZLWK EDUH KDQGV
6ORZO\ ORRVHQ FDS WR ILUVW VWRS WR UHOLHYH SUHVVXUH
EHIRUH UHPRYLQJ FRPSOHWHO\
&'( $35
31
0DLQWHQDQFH'DLO\ RU HYHU\ KRXUV
&' ²81²129
&' ²81²129
&KHFN 'XVW 8QORDGHU 9DOYH &KHFN $LU 5HVWULFWLRQ ,QGLFDWRU
,I DLU ILOWHU KDV D GXVW XQORDGHU YDOYH $ VTXHH]H 0DNH D WKRURXJK LQVSHFWLRQ RI WKH HQJLQH
YDOYH WLS WR UHOHDVH DQ\ WUDSSHG GLUW SDUWLFOHV FRPSDUWPHQW
&KHFN DLU LQWDNH UHVWULFWLRQ LQGLFDWRU % :KHQ 127( :LSH DOO ILWWLQJV FDSV DQG SOXJV EHIRUH
LQGLFDWRU LV UHG DLU ILOWHU QHHGV WR EH FOHDQHG SHUIRUPLQJ DQ\ PDLQWHQDQFH WR UHGXFH WKH
,03257$17 0D[LPXP DLU LQWDNH UHVWULFWLRQ LV FKDQFH RI V\VWHP FRQWDPLQDWLRQ
N3D EDU SVL LQ +2 $ FORJJHG
DLU FOHDQHU HOHPHQW ZLOO FDXVH H[FHVVLYH LQWDNH
UHVWULFWLRQ DQG D UHGXFHG DLU VXSSO\ WR WKH HQJLQH
&') $35
31
0DLQWHQDQFH'DLO\ RU HYHU\ KRXUV
&' ²81²)(%
&KHFN IXHO ILOWHUV & DQG ' GDLO\ IRU ZDWHU RU GHEULV DQG
GUDLQ DV QHFHVVDU\
/RRVHQ GUDLQ SOXJV $ DW ERWWRP RI ERWK IXHO ILOWHUV
WZR RU WKUHH WXUQV
/RRVHQ DLU EOHHG SOXJV % WZR IXOO WXUQV DQG GUDLQ
ZDWHU LQWR D VXLWDEOH FRQWDLQHU
'UDLQ :DWHU IURP )XHO )LOWHUV
:KHQ IXHO VWDUWV WR GUDLQ RXW WLJKWHQ GUDLQ SOXJV
VHFXUHO\ $²'UDLQ 3OXJV &²3ULPDU\ )XHO )LOWHU
%²$LU %OHHG 3OXJV '²)LQDO )XHO )LOWHU
%OHHG IXHO V\VWHP
&' 0$<
&' ²81²$35
&KHFN IXHO ILOWHUV $ DQG % GDLO\ IRU ZDWHU RU GHEULV DQG
GUDLQ DV QHFHVVDU\
/RRVHQ GUDLQ SOXJV & DW ERWWRP RI ERWK IXHO ILOWHUV
WZR RU WKUHH WXUQV
'UDLQ ZDWHU LQWR D VXLWDEOH FRQWDLQHU 'UDLQ :DWHU IURP )XHO )LOWHUV
31
0DLQWHQDQFH KRXUV
&KDQJH (QJLQH 2LO DQG )LOWHU DQG (QJLQHV
&' ²81²'(&
&' ²81²$8*
2LO 3DQ 'UDLQ 9DOYH 2LO )LOWHU
127( &KDQJH HQJLQH RLO DQG ILOWHU IRU WKH ILUVW WLPH
&' ²81²-$1
DIWHU KRXUV PD[LPXP RI RSHUDWLRQ WKHQ
HYHU\ KRXUV WKHUHDIWHU &KDQJH RLO DQG
ILOWHU DW OHDVW RQFH D \HDU
31
0DLQWHQDQFH KRXUV
&' ²81²'(&
)' ²81²0$5
2LO )LOOHU &DS &URVVKDWFK $UHD RQ 2LO 'LSVWLFN
&ORVH RLO SDQ GUDLQ YDOYH 6WDUW HQJLQH DQG UXQ WR FKHFN IRU SRVVLEOH OHDNV
)LOO HQJLQH FUDQNFDVH ZLWK FRUUHFW -RKQ 'HHUH HQJLQH 6WRS HQJLQH DQG FKHFN RLO OHYHO DIWHU PLQXWHV ,I
RLO WKURXJK RSHQLQJ RQ URFNHU DUP FRYHU ' QHFHVVDU\ WRS XS
7R GHWHUPLQH WKH FRUUHFW RLO ILOO TXDQWLW\ IRU \RXU HQJLQH
VHH WKH 6SHFLILFDWLRQV 6HFWLRQ
127( &UDQNFDVH RLO FDSDFLW\ PD\ YDU\ VOLJKWO\ $/:$<6
ILOO FUDQNFDVH WR IXOO PDUN RU ZLWKLQ FURVVKDWFK DUHD
RQ GLSVWLFN ZKLFKHYHU LV SUHVHQW '2 127 RYHUILOO
&' $35
31
0DLQWHQDQFH KRXUV
&KDQJH (QJLQH 2LO DQG )LOWHU RQ DQG (QJLQHV ([FHSW +)*+)6+)8
&' ²81²'(&
&' ²81²'(&
2LO 3DQ 'UDLQ 9DOYH 2LO )LOWHU
&' ²81²'(&
127( &KDQJH HQJLQH RLO DQG ILOWHU IRU WKH ILUVW WLPH
DIWHU KRXUV PD[LPXP RI RSHUDWLRQ WKHQ
HYHU\ KRXUV WKHUHDIWHU &KDQJH RLO DQG
ILOWHU DW OHDVW RQFH D \HDU
&'$ ²81²'(&
5HSODFH RLO ILOWHU DV IROORZV
D 5HPRYH DQG GLVFDUG RLO ILOWHU HOHPHQW % XVLQJ D
VXLWDEOH ILOWHU ZUHQFK
E $SSO\ FOHDQ HQJLQH RLO WR LQQHU & DQG RXWHU '
VHDOV DQG WR ILOWHU WKUHDGV
F :LSH ERWK VHDOLQJ VXUIDFHV ( RI WKH ILOWHU KHDGHU 2LO )LOWHU +HDGHU
ZLWK D FOHDQ UDJ (QVXUH QRWFKHV LQ GXVW VHDO )
DUH SURSHUO\ LQVWDOOHG LQ WKH VORWV LQ WKH KRXVLQJ $²2LO 'UDLQ 9DOYH '²2XWHU 6HDO
5HSODFH GXVW VHDO LI GDPDJHG %²2LO )LOWHU (OHPHQW (²6HDOLQJ 6XUIDFHV
&²,QQHU 6HDO )² 'XVW 6HDO
G ,QVWDOO DQG WLJKWHQ RLO ILOWHU E\ KDQG XQWLO LW LV WLJKW
DJDLQVW GXVW VHDO ) '2 127 RYHUWLJKWHQ
&ORVH RLO SDQ GUDLQ YDOYH
&RQWLQXHG RQ QH[W SDJH &' -81
31
0DLQWHQDQFH KRXUV
&' ²81²6(3
&' ²81²129
2LO )LOOHU &DS RQ 5RFNHU $UP &RYHU
2LO )LOOHU &DS DQG 'LSVWLFN
)LOO HQJLQH FUDQNFDVH ZLWK FRUUHFW -RKQ 'HHUH HQJLQH
RLO WKURXJK RSHQLQJ RQ URFNHU DUP FRYHU & RU RQ WKH
VLGH RI WKH HQJLQH %
7R GHWHUPLQH WKH FRUUHFW RLO ILOO TXDQWLW\ IRU \RXU HQJLQH
VHH WKH 6SHFLILFDWLRQV 6HFWLRQ
)' ²81²0$5
127( &UDQNFDVH RLO FDSDFLW\ PD\ YDU\ VOLJKWO\ $/:$<6
ILOO FUDQNFDVH WR IXOO PDUN RU ZLWKLQ FURVVKDWFK DUHD RQ
GLSVWLFN $ ZKLFKHYHU LV SUHVHQW '2 127 RYHUILOO
&' -81
31
0DLQWHQDQFH KRXUV
&KDQJH (QJLQH 2LO DQG )LOWHU +)* +)6 DQG +)8 (QJLQHV
&' ²81²$35
&' ²81²$35
2LO 3DQ 'UDLQ 9DOYH 2LO )LOWHU
&' ²81²'(&
127( &KDQJH HQJLQH RLO DQG ILOWHU IRU WKH ILUVW WLPH
DIWHU KRXUV PD[LPXP RI RSHUDWLRQ WKHQ
HYHU\ KRXUV WKHUHDIWHU &KDQJH RLO DQG
ILOWHU DW OHDVW RQFH D \HDU
&'$ ²81²'(&
5HSODFH RLO ILOWHU DV IROORZV
D 5HPRYH DQG GLVFDUG RLO ILOWHU HOHPHQW % XVLQJ D
VXLWDEOH ILOWHU ZUHQFK
E $SSO\ FOHDQ HQJLQH RLO WR LQQHU & DQG RXWHU '
VHDOV DQG WR ILOWHU WKUHDGV
F :LSH ERWK VHDOLQJ VXUIDFHV ( RI WKH ILOWHU KHDGHU 2LO )LOWHU +HDGHU
ZLWK D FOHDQ UDJ (QVXUH QRWFKHV LQ GXVW VHDO )
DUH SURSHUO\ LQVWDOOHG LQ WKH VORWV LQ WKH KRXVLQJ $²2LO 'UDLQ 9DOYH '²2XWHU 6HDO
5HSODFH GXVW VHDO LI GDPDJHG %²2LO )LOWHU (OHPHQW (²6HDOLQJ 6XUIDFHV
&²,QQHU 6HDO )² 'XVW 6HDO
G ,QVWDOO DQG WLJKWHQ RLO ILOWHU E\ KDQG XQWLO LW LV WLJKW
DJDLQVW GXVW VHDO ) '2 127 RYHUWLJKWHQ
&ORVH RLO SDQ GUDLQ YDOYH
&RQWLQXHG RQ QH[W SDJH &' -81
31
0DLQWHQDQFH KRXUV
&' ²81²$35
VHH WKH 6SHFLILFDWLRQV 6HFWLRQ
7R FKHFN RLO OHYHO SURFHHG DV IROORZV
D 5HPRYH RLO GLSVWLFNILOOHU FDS $
E :LSH GLSVWLFN EODGH WR UHPRYH RLO
F 5HLQVWDOO GLSVWLFN WKHQ WLJKWHQ E\ KDQG 2LO 'LSVWLFN)LOOHU &DS
&' ²81²$35
ZLWKRXW SHUPLWWLQJ HQJLQH WR VWDUW 7KLV ZLOO
KHOS LQVXUH DGHTXDWH OXEULFDWLRQ WR HQJLQH
FRPSRQHQWV EHIRUH HQJLQH VWDUWV
&' -81
31
0DLQWHQDQFH KRXUV
; ²81²$8*
7LJKWHQ DOO FRQQHFWLRQV EHIRUH DSSO\LQJ SUHVVXUH
.HHS KDQGV DQG ERG\ DZD\ IURP SLQKROHV DQG
QR]]OHV ZKLFK HMHFW IOXLGV XQGHU KLJK SUHVVXUH
8VH D SLHFH RI FDUGERDUG RU SDSHU WR VHDUFK
IRU OHDNV 'R QRW XVH \RXU KDQG
,I DQ\ IOXLG LV LQMHFWHG LQWR WKH VNLQ LW PXVW %HZDUH RI +LJK3UHVVXUH )OXLGV
EH VXUJLFDOO\ UHPRYHG ZLWKLQ D IHZ KRXUV
E\ D GRFWRU IDPLOLDU ZLWK WKLV W\SH LQMXU\ RU
JDQJUHQH PD\ UHVXOW 'RFWRUV XQIDPLOLDU ZLWK
WKLV W\SH RI LQMXU\ PD\ FDOO WKH 'HHUH &RPSDQ\
0HGLFDO 'HSDUWPHQW LQ 0ROLQH ,OOLQRLV RU RWKHU
NQRZOHGJHDEOH PHGLFDO VRXUFH
&' ²81²'(&
/RRVHQ GUDLQ SOXJ $ DQG DLU EOHHG SOXJ % 'UDLQ
IXHO LQWR D VXLWDEOH FRQWDLQHU
127( /LIWLQJ XS RQ UHWDLQLQJ ULQJ DV LW LV URWDWHG KHOSV
WR JHW LW SDVW UDLVHG ORFDWRUV
31
0DLQWHQDQFH KRXUV
5* ²81²'(&
ZDWHU VHSDUDWRU ERZO RQWR QHZ HOHPHQW 7LJKWHQ
VHFXUHO\
%OHHG WKH IXHO V\VWHP
31
0DLQWHQDQFH KRXUV
&KDQJH )XHO )LOWHU (OHPHQWV RQ DQG (QJLQHV ([FHSW +)*+)6+)8
; ²81²$8*
&' ²81²)(%
)XHO )LOWHUV
&$87,21 (VFDSLQJ IOXLG XQGHU SUHVVXUH FDQ ,03257$17 'R QRW GXPS WKH ROG IXHO LQWR
SHQHWUDWH WKH VNLQ FDXVLQJ VHULRXV LQMXU\ 5HOLHYH WKH QHZ ILOWHU HOHPHQW 7KLV FRXOG FDXVH
SUHVVXUH EHIRUH GLVFRQQHFWLQJ IXHO RU RWKHU OLQHV IXHO LQMHFWLRQ SUREOHPV
7LJKWHQ DOO FRQQHFWLRQV EHIRUH DSSO\LQJ SUHVVXUH
$ SOXJ LV SURYLGHG ZLWK WKH QHZ HOHPHQW IRU
.HHS KDQGV DQG ERG\ DZD\ IURP SLQKROHV DQG
SOXJJLQJ WKH XVHG HOHPHQW
QR]]OHV ZKLFK HMHFW IOXLGV XQGHU KLJK SUHVVXUH
8VH D SLHFH RI FDUGERDUG RU SDSHU WR VHDUFK
,QVSHFW ILOWHU PRXQWLQJ EDVH IRU FOHDQOLQHVV &OHDQ DV
IRU OHDNV 'R QRW XVH \RXU KDQG
UHTXLUHG
,I DQ\ IOXLG LV LQMHFWHG LQWR WKH VNLQ LW PXVW
127( 5DLVHG ORFDWRUV RQ IXHO ILOWHU FDQLVWHU PXVW
EH VXUJLFDOO\ UHPRYHG ZLWKLQ D IHZ KRXUV
EH LQGH[HG SURSHUO\ ZLWK VORWV LQ PRXQWLQJ
E\ D GRFWRU IDPLOLDU ZLWK WKLV W\SH LQMXU\ RU
EDVH IRU FRUUHFW LQVWDOODWLRQ
JDQJUHQH PD\ UHVXOW 'RFWRUV XQIDPLOLDU ZLWK
WKLV W\SH RI LQMXU\ PD\ FDOO WKH 'HHUH &RPSDQ\
,QVWDOO QHZ ILOWHU HOHPHQW GU\ RQWR PRXQWLQJ EDVH %H
0HGLFDO 'HSDUWPHQW LQ 0ROLQH ,OOLQRLV RU RWKHU
VXUH HOHPHQW LV SURSHUO\ LQGH[HG DQG ILUPO\ VHDWHG RQ
NQRZOHGJHDEOH PHGLFDO VRXUFH
EDVH ,W PD\ EH QHFHVVDU\ WR URWDWH ILOWHU IRU FRUUHFW
DOLJQPHQW
127( (QJLQHV DUH HTXLSSHG ZLWK D SULPDU\ IXHO ILOWHU
) DQG D ILQDO IXHO ILOWHU % %RWK IXHO ILOWHUV KDYH ,I HTXLSSHG ZLWK ZDWHU VHSDUDWRU ERZO ( UHPRYH
WR EH UHSODFHG WRJHWKHU DW WKH VDPH WLPH ILOWHU HOHPHQW IURP VHSDUDWRU ERZO 'UDLQ DQG FOHDQ
VHSDUDWRU ERZO 'U\ ZLWK FRPSUHVVHG DLU ,QVWDOO ERZO
7KRURXJKO\ FOHDQ IXHO ILOWHU DVVHPEO\ DQG VXUURXQGLQJ RQWR QHZ ILOWHU HOHPHQW 7LJKWHQ VHFXUHO\
DUHD
,QVWDOO UHWDLQLQJ ULQJ RQWR PRXQWLQJ EDVH PDNLQJ
'LVFRQQHFW ZDWHULQIXHO VHQVRU ZLULQJ FHUWDLQ GXVW VHDO LV LQ SODFH RQ ILOWHU EDVH +DQG WLJKWHQ
ULQJ DERXW WXUQ XQWLO LW ´VQDSV´ LQWR WKH GHWHQW '2
/RRVHQ GUDLQ SOXJ & DQG GUDLQ IXHO LQWR D VXLWDEOH
127 RYHUWLJKWHQ UHWDLQLQJ ULQJ
FRQWDLQHU
127( 7KH SURSHU LQVWDOODWLRQ LV LQGLFDWHG ZKHQ D FOLFN
127( /LIWLQJ XS RQ UHWDLQLQJ ULQJ DV LW LV URWDWHG KHOSV
LV KHDUG DQG D UHOHDVH RI WKH UHWDLQLQJ ULQJ LV IHOW
WR JHW LW SDVW UDLVHG ORFDWRUV
%OHHG WKH IXHO V\VWHP
)LUPO\ JUDVS WKH UHWDLQLQJ ULQJ $ DQG URWDWH LW
FORFNZLVH WXUQ 5HPRYH ULQJ DORQJ ZLWK ILOWHU
HOHPHQW % RU )
&' -81
31
0DLQWHQDQFH KRXUV
; ²81²$8*
7LJKWHQ DOO FRQQHFWLRQV EHIRUH DSSO\LQJ SUHVVXUH
.HHS KDQGV DQG ERG\ DZD\ IURP SLQKROHV DQG
QR]]OHV ZKLFK HMHFW IOXLGV XQGHU KLJK SUHVVXUH
8VH D SLHFH RI FDUGERDUG RU SDSHU WR VHDUFK
IRU OHDNV 'R QRW XVH \RXU KDQG
,I DQ\ IOXLG LV LQMHFWHG LQWR WKH VNLQ LW PXVW +LJK3UHVVXUH )OXLGV
EH VXUJLFDOO\ UHPRYHG ZLWKLQ D IHZ KRXUV
E\ D GRFWRU IDPLOLDU ZLWK WKLV W\SH LQMXU\ RU
JDQJUHQH PD\ UHVXOW 'RFWRUV XQIDPLOLDU ZLWK SOXJJHG IXHO ILOWHUV ORZ IXHO SUHVVXUH ,I QR
WKLV W\SH RI LQMXU\ PD\ FDOO WKH 'HHUH &RPSDQ\ DODUP VRXQGV GXULQJ WKH PRQWK VHUYLFH
0HGLFDO 'HSDUWPHQW LQ 0ROLQH ,OOLQRLV RU RWKHU LQWHUYDO UHSODFH HOHPHQWV DW WKDW WLPH RU DIWHU
NQRZOHGJHDEOH PHGLFDO VRXUFH KRXUV RSHUDWLRQ ZKLFKHYHU FRPHV ILUVW
31
0DLQWHQDQFH KRXUV
127( %RWK WKH SULPDU\ DQG WKH ILQDO IXHO ILOWHU HOHPHQWV
PXVW EH UHSODFHG DW WKH VDPH WLPH
&'$ ²81²0$5
$²:DWHULQ)XHO VHQVRU '²2ULQJ
FRQQHFWRU (²'UDLQ YDOYH
%²&DQLVWHU
&²3ULPDU\ IXHO ILOWHU HOHPHQW
31
0DLQWHQDQFH KRXUV
&' ²81²0$5
5HSODFH ILQDO IXHO ILOWHU HOHPHQW
&' -81
31
0DLQWHQDQFH KRXUV
&' ²81²0$<
D 8VH RI -'* 7HQVLRQ *DXJH $
6SHFLILFDWLRQ
%HOW WHQVLRQ²1HZ EHOW ² 1 ² OEIRUFH
8VHG EHOW ² 1 ² OEIRUFH
&' ²81²0$<
FRUUHFWO\ WHQVLRQHG
,03257$17 'R QRW SU\ DJDLQVW WKH DOWHUQDWRU
UHDU IUDPH 'R QRW WLJKWHQ RU ORRVHQ EHOWV
ZKLOH WKH\ DUH KRW
&' ²81²0$<
'36*&' $35
31
0DLQWHQDQFH KRXUV
5* ²81²2&7
VWDPSHG RQ WKH WRS HGJH RI WKH DOWHUQDWRU EUDFNHW
&' ²81²-$1
$²%HOW JDXJH '²5HIHUHQFH PDUN
%²&DS VFUHZ (²$OWHUQDWRU XSSHU EUDFNHW
&²&DS VFUHZ QRWFK
5HIHUHQFH PDUNV
'36*&' -$1
31
0DLQWHQDQFH KRXUV \HDU
&OHDQLQJ FUDQNFDVH YHQW WXEH
,I \RX RSHUDWH WKH HQJLQH LQ GXVW\ FRQGLWLRQV FOHDQ WKH
WXEH DW VKRUWHU LQWHUYDOV
5HPRYH DQG FOHDQ FUDQNFDVH YHQW WXEH $
&' ²81²$8*
,QVWDOO WKH YHQW WXEH %H VXUH WKH 2ULQJ ILWV FRUUHFWO\
LQ WKH URFNHU DUP FRYHU IRU HOERZ DGDSWHU 7LJKWHQ
KRVH FODPS VHFXUHO\
'36*&' -$1
&' ²81²$35
5* ²81²0$<
31
0DLQWHQDQFH KRXUV \HDU
&' ²81²$8*
,03257$17 7KH DLU LQWDNH V\VWHP PXVW QRW OHDN &KHFN FODPSV RQ SLSLQJ $ ZKLFK FRQQHFW WKH DLU
$Q\ OHDN QR PDWWHU KRZ VPDOO PD\ UHVXOW LQ ILOWHU HQJLQH DQG LI SUHVHQW WXUERFKDUJHU DQG DLUWRDLU
HQJLQH IDLOXUH GXH WR DEUDVLYH GLUW DQG GXVW UDGLDWRU 7LJKWHQ FODPSV DV QHFHVVDU\
HQWHULQJ WKH LQWDNH V\VWHP
7HVW DLU UHVWULFWLRQ LQGLFDWRU % IRU SURSHU RSHUDWLRQ
,QVSHFW DOO LQWDNH KRVHV SLSLQJ IRU FUDFNV 5HSODFH 5HSODFH LQGLFDWRU DV QHFHVVDU\
DV QHFHVVDU\
'36*&' -$1
,I HQJLQH KDV D UXEEHU GXVW XQORDGHU YDOYH & LQVSHFW
WKH YDOYH RQ ERWWRP RI DLU ILOWHU IRU FUDFNV RU SOXJJLQJ
5HSODFH DV QHFHVVDU\
6HUYLFH DLU ILOWHU DV QHFHVVDU\
5* ²81²'(&
'36*&' -$1
31
0DLQWHQDQFH KRXUV \HDU
5* ²81²129
ZLWKLQ VSHFLILFDWLRQ UHSODFH WHQVLRQHU DVVHPEO\
&KHFNLQJ EHOW ZHDU
7KH EHOW WHQVLRQHU LV GHVLJQHG WR RSHUDWH ZLWKLQ WKH OLPLW
RI DUP PRYHPHQW SURYLGHG E\ WKH FDVW VWRSV $ DQG %
ZKHQ FRUUHFW EHOW OHQJWK DQG JHRPHWU\ LV XVHG ,I WKH
WHQVLRQHU VWRS RQ VZLQJ DUP $ LV KLWWLQJ WKH IL[HG VWRS (DUOLHU GHVLJQ WHQVLRQHU
% FKHFN PRXQWLQJ EUDFNHWV DOWHUQDWRU EHOW WHQVLRQHU
LGOHU SXOOH\ HWF DQG WKH EHOW OHQJWK 5HSODFH EHOW DV
QHHGHG VHH 5HSODFLQJ )DQ DQG $OWHUQDWRU %HOW
DQG (QJLQHV ZLWK $XWRPDWLF 7HQVLRQHU
5* ²81²129
/DWHU GHVLJQ WHQVLRQHU
31
0DLQWHQDQFH KRXUV \HDU
5* ²81²129
E 5HOHDVH WHQVLRQ RQ WHQVLRQ DUP DQG UHPRYH EUHDNHU
EDU
F 3XW D PDUN $ RQ VZLQJ DUP RI WHQVLRQHU DV VKRZQ
G 0HDVXUH PP LQ IURP $ DQG SXW D PDUN %
RQ WHQVLRQHU PRXQWLQJ EDVH
127( (DUOLHU HQJLQHV KDYH D /()7+$1' WKUHDG 0DUNV RQ WHQVLRQHU
UROOHU FDS VFUHZ ZKLOH ODWHU HQJLQHV KDYH D
PP LQ VTXDUH KROH LQ WHQVLRQHU
5* ²81²-$1
I 5HFRUG WRUTXH ZUHQFK PHDVXUHPHQW DQG FRPSDUH
ZLWK VSHFLILFDWLRQ EHORZ 5HSODFH WHQVLRQHU DVVHPEO\
DV UHTXLUHG
6SHFLILFDWLRQ
6SULQJ²)RUFH ² 1ÂP ² OEIW
$OLJQ PDUNV
$²0DUN RQ VZLQJ DUP %²0DUN RQ WHQVLRQHU
PRXQWLQJ EDVH
'36*&' $35
&' ²81²0$<
$GMXVW HQJLQH YDOYH FOHDUDQFH DV IROORZV RU KDYH \RXU
DXWKRUL]HG VHUYLFLQJ GHDOHU RU HQJLQH GLVWULEXWRU DGMXVW
WKH HQJLQH YDOYH FOHDUDQFH
5HPRYH URFNHU DUP FRYHU DQG FUDQNFDVH YHQW WXEH
8VLQJ -'( RU -'* )O\ZKHHO 7XUQLQJ 7RRO $
URWDWH HQJLQH IO\ZKHHO LQ UXQQLQJ GLUHFWLRQ FORFNZLVH
YLHZHG IURP ZDWHU SXPS XQWLO 1R SLVWRQ IURQW
KDV UHDFKHG WRS GHDG FHQWHU 7'& RQ FRPSUHVVLRQ
VWURNH ,QVHUW WLPLQJ SLQ -'( RU -'* % LQWR
IO\ZKHHO ERUH
&RQWLQXHG RQ QH[W SDJH '36*&' -$1
31
0DLQWHQDQFH KRXUV \HDU
&' ²81²0$<
127( ,I URFNHU DUP LV HTXLSSHG ZLWK DGMXVWLQJ VFUHZ
DQG MDP QXW $ WLJKWHQ MDP QXW WR 1ÂP
OEIW DIWHU DGMXVWLQJ YDOYH FOHDUDQFH
5* ²81²$8*
YDOYHV DQG 1R DQG LQWDNH YDOYHV
F 5RWDWH IO\ZKHHO /RFN 1R SLVWRQ DW 7'&
H[KDXVW VWURNH (
G $GMXVW YDOYH FOHDUDQFH RQ 1R H[KDXVW YDOYH DQG
1R LQWDNH YDOYH
&\OLQGHU (QJLQH
127( )LULQJ RUGHU LV
&' ²81²-81
VWURNH
'36*&' -$1
31
0DLQWHQDQFH KRXUV \HDU
5* ²81²-$1
5* ²81²-$1
7HVW UDGLDGRU FDS
&$87,21 ([SORVLYH UHOHDVH RI IOXLGV IURP $OORZ HQJLQHV WR FRRO WKHQ FDUHIXOO\ UHPRYH UDGLDWRU
SUHVVXUL]HG FRROLQJ V\VWHP FDQ FDXVH FDS
VHULRXV EXUQV
)LOO UDGLDWRU ZLWK FRRODQW WR WKH QRUPDO RSHUDWLQJ OHYHO
6KXW RII HQJLQHV 2QO\ UHPRYH ILOOHU FDS ZKHQ
,03257$17 '2 127 DSSO\ H[FHVVLYH SUHVVXUH
FRRO HQRXJK WR WRXFK ZLWK EDUH KDQGV 6ORZO\
WR FRROLQJ V\VWHP GRLQJ VR PD\ GDPDJH
ORRVHQ FDS WR ILUVW VWRS WR UHOLHYH SUHVVXUH
UDGLDWRU DQG KRVHV
EHIRUH UHPRYLQJ FRPSOHWHO\
&RQQHFW JDXJH DQG DGDSWHU WR UDGLDWRU ILOOHU QHFN
7HVW 5DGLDWRU &DS
3UHVVXUL]H FRROLQJ V\VWHP WR VSHFLILFDWLRQ OLVWHG IRU
5HPRYH UDGLDWRU FDS DQG DWWDFK WR '67 WHVWHU UDGLDWRU FDS
DV VKRZQ :LWK SUHVVXUH DSSOLHG FKHFN DOO FRROLQJ V\VWHP KRVH
3UHVVXUL]H FDS WR VSHFLILFDWLRQ OLVWHG *DXJH VKRXOG FRQQHFWLRQV UDGLDWRU DQG RYHUDOO HQJLQH IRU OHDNV
KROG SUHVVXUH IRU VHFRQGV ZLWKLQ WKH QRUPDO UDQJH ,I OHDNDJH LV GHWHFWHG FRUUHFW DV QHFHVVDU\ DQG
LI FDS LV DFFHSWDEOH SUHVVXUH WHVW V\VWHP DJDLQ
,I JDXJH GRHV QRW KROG SUHVVXUH UHSODFH UDGLDWRU FDS ,I QR OHDNDJH LV GHWHFWHG EXW WKH JDXJH LQGLFDWHG D
6SHFLILFDWLRQ GURS LQ SUHVVXUH FRRODQW PD\ EH OHDNLQJ LQWHUQDOO\
5DGLDWRU &DS ZLWKLQ WKH V\VWHP RU DW WKH EORFNWRKHDG JDVNHW +DYH
&DOLEUDWLRQ²3UHVVXUH N3D EDU \RXU HQJLQH GLVWULEXWRU RU VHUYLFLQJ GHDOHU FRUUHFW WKLV
SVL IRU VHFRQGV PLQLPXP SUREOHP LPPHGLDWHO\
5HPRYH WKH FDS IURP JDXJH WXUQ LW DQG UHWHVW
FDS WR FRQILUP PHDVXUHPHQW
7HVW &RROLQJ 6\VWHP
127( (QJLQH VKRXOG EH ZDUPHG XS WR WHVW
RYHUDOO FRROLQJ V\VWHP
&'(& $35
31
0DLQWHQDQFH KRXUV \HDUV
&KHFN DQG DGMXVW HQJLQH YDOYH FOHDUDQFH
DQG (QJLQHV
$GMXVW HQJLQH YDOYH FOHDUDQFH DV IROORZV RU KDYH \RXU
DXWKRUL]HG VHUYLFLQJ GHDOHU RU HQJLQH GLVWULEXWRU DGMXVW
WKH HQJLQH YDOYH FOHDUDQFH
&' ²81²0$<
5HPRYH URFNHU DUP FRYHU DQG FUDQNFDVH YHQW WXEH
8VLQJ -'( RU -'* )O\ZKHHO 7XUQLQJ 7RRO $
URWDWH HQJLQH IO\ZKHHO LQ UXQQLQJ GLUHFWLRQ FORFNZLVH
YLHZHG IURP ZDWHU SXPS XQWLO 1R SLVWRQ IURQW
KDV UHDFKHG WRS GHDG FHQWHU 7'& RQ FRPSUHVVLRQ
VWURNH ,QVHUW WLPLQJ SLQ -'* RU -'( % LQWR
IO\ZKHHO ERUH
&RQWLQXHG RQ QH[W SDJH '36*&' $35
31
0DLQWHQDQFH KRXUV \HDUV
5* ²81²$8*
,I YDOYHV QHHG DGMXVWLQJ ORRVHQ WKH ORFNQXW RQ URFNHU
DUP DGMXVWLQJ VFUHZ 7XUQ DGMXVWLQJ VFUHZ XQWLO IHHOHU
JDXJH VOLSV ZLWK D VOLJKW GUDJ +ROG WKH DGMXVWLQJ
VFUHZ IURP WXUQLQJ ZLWK VFUHZGULYHU DQG WLJKWHQ
ORFNQXW WR 1ÂP OEIW 5HFKHFN FOHDUDQFH DIWHU
WLJKWHQLQJ ORFNQXW 5HDGMXVW FOHDUDQFH DV QHFHVVDU\
5HLQVWDOO URFNHU DUP FRYHU DQG FUDQNFDVH YHQW WXEH
&\OLQGHU (QJLQH
127( )LULQJ RUGHU LV
5* ²81²2&7
D /RFN 1R SLVWRQ DW 7'& FRPSUHVVLRQ VWURNH %
E $GMXVW YDOYH FOHDUDQFH RQ 1R DQG H[KDXVW
YDOYHV DQG 1R DQG LQWDNH YDOYHV
F 5RWDWH IO\ZKHHO /RFN 1R SLVWRQ DW 7'&
FRPSUHVVLRQ VWURNH &
G $GMXVW YDOYH FOHDUDQFH RQ 1R DQG H[KDXVW
YDOYHV DQG 1R DQG LQWDNH YDOYHV
&\OLQGHU (QJLQH $²)URQW RI HQJLQH (²([KDXVW YDOYH
127( )LULQJ RUGHU LV %²1R 3LVWRQ DW 7'& ,² ,QWDNH YDOYH
FRPSUHVVLRQ VWURNH
&²1R 3LVWRQ DW 7'&
D /RFN 1R SLVWRQ DW 7'& FRPSUHVVLRQ VWURNH % FRPSUHVVLRQ VWURNH
E $GMXVW YDOYH FOHDUDQFH RQ 1R DQG H[KDXVW
YDOYHV DQG 1R DQG LQWDNH YDOYHV
F 5RWDWH IO\ZKHHO /RFN 1R SLVWRQ DW 7'&
FRPSUHVVLRQ VWURNH &
G $GMXVW YDOYH FOHDUDQFH RQ 1R DQG H[KDXVW
YDOYHV DQG 1R DQG LQWDNH YDOYHV
5* ²81²2&7
$²)URQW RI HQJLQH (²([KDXVW YDOYH
%²1R 3LVWRQ DW 7'& ,² ,QWDNH YDOYH
FRPSUHVVLRQ VWURNH
&²1R 3LVWRQ DW 7'&
FRPSUHVVLRQ VWURNH
'36*&' $35
31
0DLQWHQDQFH KRXUV \HDUV
&' ²81²6(3
6SHFLILFDWLRQ
)DVW LGOH² +]
*HQHUDWRU VHW ² USP
+] *HQHUDWRU VHW ² USP
'36*&' -$1
&' ²81²6(3
$SSO\ IXOO ORDG
,I VSHFLILHG SRZHU FDQQRW EH REWDLQHG WXUQ VFUHZ %
WR DGMXVW GURRS XQWLO WKH UHTXHVWHG SRZHU LV UHDFKHG
127( ,I VXUJLQJ H[LWV XSRQ UHPRYLQJ WKH ORDG WXUQ
VFUHZ % FORFNZLVH WR HOLPLQDWH
'36*&' -$1
31
0DLQWHQDQFH KRXUV \HDUV
5* ²81²-$1
GHIHFWLYH DQG VKRXOG EH UHSODFHG
,03257$17 7KH YLEUDWLRQ GDPSHU DVVHPEO\ LV QRW
UHSDLUDEOH DQG VKRXOG EH UHSODFHG HYHU\
KRXUV RU \HDUV ZKLFKHYHU RFFXUV ILUVW
5* ²81²129
VSHFLILFDWLRQV JLYHQ EHORZ UHSODFH YLEUDWLRQ GDPSHU
6SHFLILFDWLRQ
'DPSHU²0D[LPXP
UDGLDO UXQRXW PP LQ
'36*&' -$1
31
0DLQWHQDQFH KRXUV \HDUV
'UDLQ DQG )OXVK &RROLQJ 6\VWHP
127( 'UDLQ DQG IOXVK FRROLQJ V\VWHP HYHU\ KRXUV
\HDUV ZKHQ -RKQ 'HHUH &22/*$5' ,, FRRODQW LV
XVHG 2WKHUZLVH HYHU\ KRXUV \HDUV
76 ²81²$35
SUHVVXUL]HG FRROLQJ V\VWHP FDQ FDXVH
VHULRXV EXUQV
6KXW RII HQJLQH 2QO\ UHPRYH ILOOHU FDS ZKHQ
FRRO HQRXJK WR WRXFK ZLWK EDUH KDQGV 6ORZO\
ORRVHQ FDS WR ILUVW VWRS WR UHOLHYH SUHVVXUH
EHIRUH UHPRYLQJ FRPSOHWHO\
D (QJLQHV
5* ²81²'(&
(QJLQH %ORFN 'UDLQ 3OXJ
&' -8/
3OXJ
31
0DLQWHQDQFH KRXUV \HDUV
&' ²81²$35
&' -8/
&' ²81²$8*
SRVVLEOH UXVW RU VHGLPHQW
6WRS HQJLQH DQG LPPHGLDWHO\ GUDLQ WKH ZDWHU IURP
V\VWHP EHIRUH UXVW DQG VHGLPHQW VHWWOH
$IWHU GUDLQLQJ ZDWHU FORVH DOO GUDLQ RULILFHV )LOO
WKH FRROLQJ V\VWHP ZLWK FOHDQLQJ SURGXFW VXFK DV
30&& RU 30&& &RROLQJ 6\VWHP &OHDQHUV
DYDLODEOH IURP \RXU -RKQ 'HHUH 'HDOHU )ROORZ 5DGLDWRU 'UDLQ 9DOYH
GLUHFWLRQV RI WKH PDQXIDFWXUHU RQ ODEHO
&²5DGLDWRU 'UDLQ 9DOYH
$IWHU FOHDQLQJ WKH FRROLQJ V\VWHP GUDLQ FOHDQHU DQG
ILOO ZLWK ZDWHU WR IOXVK WKH V\VWHP 5XQ HQJLQH XQWLO
ZDWHU SDVVHV WKURXJK WKH WKHUPRVWDW WKHQ GUDLQ RXW &RROLQJ V\VWHP FDSDFLW\
IOXVKLQJ ZDWHU (QJLQH 0RGHO &RROLQJ V\VWHP FDSDFLW\
&KHFN FRROLQJ V\VWHP KRVHV IRU SURSHU FRQGLWLRQ ') 7) / TW
5HSODFH DV QHFHVVDU\ +)8 7)8
') 7) / TW
&ORVH DOO GUDLQ RULILFHV DQG ILOO WKH FRROLQJ V\VWHP ZLWK ') / TW
VSHFLILHG FRRODQW VHH +HDY\ 'XW\ 'LHVHO (QJLQH
7) 7) / TW
&RRODQW 7)8
+) +)8 / TW
7) 7)
+)8 +) / TW
+) +)8
+)8
+)8 / TW
+)8 / TW
31
0DLQWHQDQFH KRXUV \HDUV
&' ²81²0$<
%²&RRODQW 7HPSHUDWXUH
6HQVRU
&' -8/
31
0DLQWHQDQFH$V UHTXLUHG
$GGLWLRQDO VHUYLFH LQIRUPDWLRQ
7KLV PDQXDO GRHV QRW DOORZ D FRPSOHWH UHSDLU RI \RXU
HQJLQH ,I \RX ZDQW ZDQW PRUH GHWDLOHG VHUYLFH LQIRUPDWLRQ
WKH IROORZLQJ SXEOLFDWLRQV DUH DYDLODEOH IURP \RXU UHJXODU
SDUWV FKDQQHO
3& ² 3DUWV &DWDORJ IRU 1RQ(PLVVLRQ &HUWLILHG
5* ²81²'(&
(QJLQHV
3& ² 3DUWV &DWDORJ IRU 6WDJH ,, (PLVVLRQ &HUWLILHG
(QJLQHV
3& ² 3DUWV &DWDORJ IRU +)* (QJLQHV
3& ² 3DUWV &DWDORJ IRU +)8 (QJLQHV
3& ² 3DUWV &DWDORJ IRU +)6 (QJLQHV
&70 ² &RPSRQHQW 7HFKQLFDO 0DQXDO IRU 2(0
(QJLQH DFFHVVRULHV (QJOLVK RQO\
&70 ² &RPSRQHQW 7HFKQLFDO 0DQXDO IRU DQG &70 ² &RPSRQHQW 7HFKQLFDO 0DQXDO IRU '(
)XHO 6\VWHPV RQ DQG HQJLQHV (QJOLVK
EDVH HQJLQHV (QJOLVK
&70 ² &RPSRQHQW 7HFKQLFDO 0DQXDO IRU +3&5
&70 ² &RPSRQHQW 7HFKQLFDO 0DQXDO IRU )XHO 6\VWHP RQ DQG ZLWK 9DOYH +HDG
0HFKDQLFDO )XHO 6\VWHPV RQ DQG HQJLQHV (QJLQHV (QJOLVK
(QJOLVK
&70 ² &RPSRQHQW 7HFKQLFDO 0DQXDO IRU
&70 ² &RPSRQHQW 7HFKQLFDO 0DQXDO IRU +3&5 3RZHU7HFK (QJLQH L7 SODWIRUP (QJOLVK 7R EH XVHG
)XHO 6\VWHP RQ DQG /HYHO ZLWK 9DOYH IRU +)* +)6 DQG +)8 (QJLQHV
+HDG (QJLQHV (QJOLVK
&70 ² &RPSRQHQW 7HFKQLFDO 0DQXDO IRU +3&5
)XHO 6\VWHP RQ DQG /HYHO ZLWK 9DOYH
+HDG (QJLQHV (QJOLVK
'36*&' -8/
31
0DLQWHQDQFH$V UHTXLUHG
76 ²81²0$5
RWKHU FRPSRQHQWV EHWZHHQ WKH KLJKSUHVVXUH
IXHO SXPS DQG QR]]OHV RQ HQJLQHV ZLWK +LJK
3UHVVXUH &RPPRQ 5DLO +3&5 IXHO V\VWHP
2QO\ WHFKQLFLDQV IDPLOLDU ZLWK WKLV W\SH RI V\VWHP
FDQ SHUIRUP UHSDLUV 6HH \RXU -RKQ 'HHUH GHDOHU
+LJK3UHVVXUH )XHO /LQHV
,03257$17 1HYHU VWHDP FOHDQ RU SRXU FROG ZDWHU
RQ DQ LQMHFWLRQ SXPS ZKLOH LW LV VWLOO ZDUP 7R
GR VR PD\ FDXVH VHL]XUH RI SXPS SDUWV
0RGLILFDWLRQ RU DOWHUDWLRQ RI LQMHFWLRQ SXPS RU
KLJKSUHVVXUH IXHO SXPS $ LQMHFWLRQ WLPLQJ
RU IXHO LQMHFWRUV LQ ZD\V QRW UHFRPPHQGHG E\
5* ²81²129
WKH PDQXIDFWXUHU ZLOO WHUPLQDWH WKH ZDUUDQW\
REOLJDWLRQ WR WKH SXUFKDVHU
,Q DGGLWLRQ WDPSHULQJ ZLWK IXHO V\VWHP ZKLFK
DOWHUV HPLVVLRQUHODWHG HTXLSPHQW RQ HQJLQHV
PD\ UHVXOW LQ ILQHV RU RWKHU SHQDOWLHV SHU (3$
UHJXODWLRQV RU RWKHU ORFDO HPLVVLRQ ODZV
)XHO 6\VWHP
'R QRW DWWHPSW WR VHUYLFH LQMHFWLRQ SXPS RU
IXHO LQMHFWRUV \RXUVHOI 6SHFLDO WUDLQLQJ DQG
VSHFLDO WRROV DUH UHTXLUHG 6HH \RXU DXWKRUL]HG $²+LJK3UHVVXUH )XHO 3XPS
VHUYLFLQJ GHDOHU RU HQJLQH GLVWULEXWRU
&' $35
31
0DLQWHQDQFH$V UHTXLUHG
&' ²81²6(3
7KRURXJKO\ FOHDQ DOO GLUW DURXQG DLU ILOWHU DUHD
/RRVHQ FODPS % WKHQ UHPRYH DLU ILOWHU
,03257$17 1HYHU UHLQVWDOO DQ DLU ILOWHU ZKLFK VKRZV
HYLGHQFH RI EDG FRQGLWLRQ SXQFKHG GHQWHG
DOORZLQJ QR ILOWHUHG DLU WR HQWHU WKH HQJLQH
5* ²81²)(%
)XOO\ GHSUHVV DLU UHVWULFWLRQ LQGLFDWRU UHVHW EXWWRQ DQG
UHOHDVH WR UHVHW LQGLFDWRU
&KHFN DLU V\VWHP HQWLUHO\ IRU SURSHU FRQGLWLRQ VHH
&KHFNLQJ $LU ,QWDNH 6\VWHP
'36*&' $35
31
0DLQWHQDQFH$V UHTXLUHG
&' ²81²$8*
$²3ULPDU\ HOHPHQW &²$LU UHVWULFWLRQ LQGLFDWRU '²:LQJ QXW
%²6HFRQGDU\ VDIHW\ HOHPHQW
127( 7KH SURFHGXUH IRU FOHDQLQJ RU UHSODFLQJ ,03257$17 ,I SULPDU\ HOHPHQW VKRZV HYLGHQFH RI
DLU ILOWHU HOHPHQW FDQ YDU\ GHSHQGLQJ RQ EDG FRQGLWLRQ SXQFKHG GHQWHG UHSODFH ERWK
DLU ILOWHU FRQILJXUDWLRQ WKH SULPDU\ DQG WKH VHFRQGDU\ HOHPHQWV
&OHDQ DLU ILOWHU ZKHQ UHVWULFWLRQ LQGLFDWRU & LV UHG &OHDQ SULPDU\ HOHPHQW ZLWK FRPSUHVVHG DLU ZRUNLQJ
5HSODFH ERWK SULPDU\ $ DQG VHFRQGDU\ % ILOWHU IURP ´FOHDQ´ WR ´GLUW\´ VLGH
HOHPHQWV DIWHU SULPDU\ HOHPHQW KDV EHHQ FOHDQHG VL[
WLPHV RU DW OHDVW RQFH D \HDU 127( &RPSUHVVHG DLU SUHVVXUH PXVW QRW H[FHHG
N3D EDU SVL
3URFHHG DV IROORZV
7KRURXJKO\ FOHDQ DOO GLUW DURXQG DLU ILOWHU DUHD 0DUN DLU ILOWHU WR NHHS WUDFN RI HDFK FOHDQLQJ RSHUDWLRQ
5HPRYH ZLQJ QXW ' DQG UHPRYH SULPDU\ HOHPHQW )XOO\ GHSUHVV DLU UHVWULFWLRQ LQGLFDWRU UHVHW EXWWRQ DQG
$ IURP FDQLVWHU UHOHDVH WR UHVHW LQGLFDWRU
,03257$17 'R QRW DWWHPSW WR FOHDQ WKH VHFRQGDU\ &KHFN DLU V\VWHP HQWLUHO\ IRU SURSHU FRQGLWLRQ VHH
VDIHW\ HOHPHQW % ,W PXVW EH RQO\ UHSODFHG &KHFNLQJ $LU ,QWDNH 6\VWHP
DV UHFRPPHQGHG
31
0DLQWHQDQFH$V UHTXLUHG
5HSODFLQJ IDQ DQG DOWHUQDWRU EHOW DQG (QJLQHV ZLWK $XWRPDWLF 7HQVLRQHU
&' ²81²6(3
&' ²81²6(3
,QVWDOODWLRQ RQ HQJLQHV ,QVWDOODWLRQ RQ HQJLQHV H[FHSW +)*+)6+)8
&' ²81²$35
$/7² $OWHUQDWRU ,² ,GOHU 3XOOH\
&3²&UDQN 3XOOH\ 7² $XWRPDWLF 7HQVLRQHU
)'²)DQ 'ULYH :3²:DWHU 3XPS
'36*&' -81
31
0DLQWHQDQFH$V UHTXLUHG
; ²81²$8*
8VH D SLHFH RI FDUGERDUG RU SDSHU WR VHDUFK
IRU OHDNV 'R QRW XVH \RXU KDQG
,I $1< IOXLG LV LQMHFWHG LQWR WKH VNLQ LW PXVW
EH VXUJLFDOO\ UHPRYHG ZLWKLQ D IHZ KRXUV E\
D GRFWRU IDPLOLDU ZLWK WKLV W\SH RI LQMXU\ RU
JDQJUHQH PD\ UHVXOW 'RFWRUV XQIDPLOLDU ZLWK
WKLV W\SH RI LQMXU\ PD\ FDOO WKH 'HHUH &RPSDQ\
0HGLFDO 'HSDUWPHQW LQ 0ROLQH ,OOLQRLV RU RWKHU WZR IXHO ILOWHUV SULPDU\ DQG ILQDO :KHQHYHU WKH
NQRZOHGJHDEOH PHGLFDO VRXUFH IXHO V\VWHP KDV EHHQ RSHQHG XS IRU VHUYLFH OLQHV
GLVFRQQHFWHG RU ILOWHUV UHPRYHG LW ZLOO EH QHFHVVDU\
127( (QJLQHV ZLWK PHFKDQLFDO IXHO V\VWHP KDYH D WR EOHHG DLU IURP WKH V\VWHP 2Q GXDO IXHO ILOWHU
VLQJOH IXHO ILOWHU ZKLOH HOHFWURQLFDOO\ FRQWUROOHG V\VWHP EOHHG DLU RQO\ IURP ILQDO ILOWHU
HQJLQHV '( DQG +3&5 IXHO V\VWHPV KDYH
&'$ -81
5*$ ²81²-$1
5* ²81²129
/RRVHQ WKH DLU EOHHG VFUHZ $ WZR IXOO WXUQV 2Q 6WDUW HQJLQH DQG FKHFN IRU OHDNV
'( IXHO V\VWHP ORRVHQ RQO\ DLU EOHHG VFUHZ RQ ILQDO
IXHO ILOWHU ,I HQJLQH GRHV QRW VWDUW LW ZLOO EH QHFHVVDU\ WR EOHHG
DLU IURP IXHO V\VWHP DW IXHO LQMHFWLRQ SXPS RU LQMHFWLRQ
2SHUDWH IXHO SXPS SULPHU OHYHU % XQWLO IXHO IORZ LV QR]]OHV DV H[SODLQHG QH[W
IUHH IURP DLU EXEEOHV
7LJKWHQ EOHHG VFUHZ VHFXUHO\ FRQWLQXH RSHUDWLQJ KDQG
SULPHU XQWLO SXPSLQJ DFWLRQ LV QRW IHOW
&RQWLQXHG RQ QH[W SDJH &'$ -81
31
0DLQWHQDQFH$V UHTXLUHG
&' ²81²6(3
&' ²81²)(%
0HFKDQLFDO ,QMHFWLRQ 3XPS )XHO 5HWXUQ /LQH '( )XHO 5HWXUQ /LQH
5* ²81²-$1
1ÂP OEIW
F 5HSHDW SURFHGXUH IRU UHPDLQLQJ LQMHFWLRQ QR]]OHV LI
QHFHVVDU\ XQWLO DOO DLU KDV EHHQ UHPRYHG IURP IXHO
V\VWHP
,I HQJLQH VWLOO ZLOO QRW VWDUW VHH \RXU DXWKRUL]HG
VHUYLFLQJ GHDOHU RU HQJLQH GLVWULEXWRU %OHHG )XHO 6\VWHP DW )XHO ,QMHFWLRQ 1R]]OHV
31
0DLQWHQDQFH$V UHTXLUHG
5* ²81²0$<
76 ²81²0$5
)LQDO )XHO )LOWHU %OHHG 6FUHZ
5* ²81²0$<
IORZ LV IUHH IURP DLU EXEEOHV
7LJKWHQ EOHHG VFUHZ VHFXUHO\ &RQWLQXH RSHUDWLQJ
SULPHU XQWLO SXPSLQJ DFWLRQ LV QRW IHOW
6WDUW HQJLQH DQG FKHFN IRU OHDNV
,I HQJLQH ZLOO QRW VWDUW UHSHDW VWHSV )XHO 3XPS 3ULPHU /HYHU
&'$ -81
,I HQJLQH ZLOO QRW VWDUW DIWHU ILOWHU FKDQJH WXUQ LJQLWLRQ NH\
21 IRU VHFRQGV WR SULPH WKH IXHO V\VWHP ,W PD\ EH
QHFHVVDU\ WR WXUQ WKH NH\ 2)) DQG 21 DJDLQ WR UHSULPH
WKH V\VWHP EHIRUH VWDUWLQJ
&' ²81²$35
&'$ -81
31
7URXEOHVKRRWLQJ
*HQHUDO WURXEOHVKRRWLQJ LQIRUPDWLRQ
7URXEOHVKRRWLQJ HOHFWURQLFDOO\ FRQWUROOHG HQJLQH SUREOHPV 'LDJQRVH WKH SUREOHP VWDUWLQJ ZLWK WKH HDVLHVW WKLQJV
FDQ EH GLIILFXOW 7KH ILUVW WKLQJ WR GR LV WR LGHQWLI\ WKH W\SH ILUVW
RI SUREOHP ZKLFK FDQ EH PHFKDQLFDO RU HOHFWULFDO 'RXEOHFKHFN EHIRUH EHJLQQLQJ WKH GLVDVVHPEO\
$Q HQJLQH ZLULQJ OD\RXW LV SURYLGHG LQ WKLV VHFWLRQ WR
'HWHUPLQH FDXVH DQG PDNH D WKRURXJK UHSDLU
LGHQWLI\ HOHFWULFDO FRPSRQHQWV HQJLQH FRQWUROOHU VHQVRUV
$IWHU PDNLQJ UHSDLUV RSHUDWH WKH HQJLQH XQGHU QRUPDO
FRQGLWLRQV WR YHULI\ WKDW WKH SUREOHP DQG FDXVH ZDV
FRQQHFWRUV FRUUHFWHG
/DWHU LQ WKLV VHFWLRQ LV D OLVW RI SRVVLEOH HQJLQH SUREOHPV 127( DQG HQJLQHV KDYH HOHFWURQLF FRQWURO
DQG GLDJQRVWLF WURXEOH FRGHV WKDW PD\ EH HQFRXQWHUHG V\VWHPV ZKLFK PD\ JHQHUDWH GLDJQRVWLF WURXEOH
DFFRPSDQLHG E\ SRVVLEOH FDXVHV DQG FRUUHFWLRQV 7KLV FRGHV WR VLJQDO SUREOHPV VHH 'LVSOD\LQJ RI
WURXEOHVKRRWLQJ LQIRUPDWLRQ LV RI D JHQHUDO QDWXUH 'LDJQRVWLF 7URXEOH &RGHV
6HH DOVR WKH JHQHUDWRU GRFXPHQWDWLRQ IRU D FRPSOHWH
LQIRUPDWLRQ RI \RXU DSSOLFDWLRQ ,I GLDJQRVWLF WURXEOH FRGHV DUH SUHVHQW SHUIRUP
WKH VXJJHVWHG FRUUHFWLYH DFWLRQV
$ UHOLDEOH SURJUDP IRU WURXEOHVKRRWLQJ HQJLQH SUREOHPV ,I WKLV GRHV QRW FRUUHFW WKH HQJLQH SUREOHP
VKRXOG LQFOXGH WKH IROORZLQJ EDVLF GLDJQRVWLF WKRXJKW FRQWDFW \RXU VHUYLFLQJ GHDOHU
SURFHVV ,I HQJLQH KDV SUREOHPV EXW QR GLDJQRVWLF
.QRZ WKH HQJLQH DQG DOO UHODWHG V\VWHPV WURXEOH FRGHV DUH GLVSOD\HG UHIHU WR (QJLQH
6WXG\ WKH SUREOHP WKRURXJKO\ 7URXEOHVKRRWLQJ IRU SUREOHPV DQG VROXWLRQV
5HODWH WKH V\PSWRPV WR \RXU NQRZOHGJH RI HQJLQH DQG
V\VWHPV
&'' $35
5* ²81²129
SURSHUO\ 6HH (QJLQH 7URXEOHVKRRWLQJ LQ WKLV VHFWLRQ
127( 'LDJQRVWLF JDXJH $ XVHV WKH PHQX NH\ %
WR DFFHVV YDULRXV HQJLQH IXQFWLRQV 7ZR DUURZ
NH\V & DUH XVHG WR VFUROO WKURXJK WKH HQJLQH
SDUDPHWHU OLVW DQG YLHZ WKH PHQX OLVW 7KH NH\
' LV XVHG IRU VHOHFWLQJ KLJKOLJKWHG LWHPV
7URXEOH &RGH 'LVSOD\ 2Q ,QVWUXPHQW 3DQHO
5HDG DQG UHFRUG '7&V GLVSOD\HG RQ /&' RI
GLDJQRVWLF JDXJH $ )RU SURFHGXUH WR DFFHVV GLDJQRVWLF $²'LDJQRVWLF *DXJH &²$UURZ .H\V
WURXEOH FRGHV UHIHU WR 8VLQJ 'LDJQRVWLF *DXJH WR $FFHVV %²0HQX .H\ '²(QWHU .H\
(QJLQH ,QIRUPDWLRQ HDUOLHU LQ WKLV PDQXDO
*R WR WKH /LVWLQJ RI 'LDJQRVWLF 7URXEOH &RGHV '7&V
ODWHU LQ WKLV VHFWLRQ WR LQWHUSUHW WKH '7&V SUHVHQW
&RQWDFW \RXU QHDUHVW HQJLQH GLVWULEXWRU RU VHUYLFLQJ
GHDOHU ZLWK D OLVW RI '7&V VR WKDW QHFHVVDU\ UHSDLUV FDQ
EH PDGH
&' 0$<
31
7URXEOHVKRRWLQJ
8VLQJ EOLQN FRGH PHWKRG IRU UHWULHYLQJ 'LDJQRVWLF 7URXEOH &RGHV '7&
V
127( 7KH PHWKRG EHORZ DSSOLHV WR DSSOLFDWLRQV KDYLQJ ,I WKHUH DUH QR DFWLYH '7&V WKH )DXOW /DPS ZLOO IODVK
D IDXOW ODPS RQ LQVWUXPHQW SDQHO UHIHU WR WKH D FRGH
JHQHUDWRU GRFXPHQWDWLRQ IRU PRUH LQIRUPDWLRQ
)ROORZLQJ WKH DFWLYH FRGHV WKH )DXOW /DPS ZLOO IODVK
7KH (OHFWURQLF &RQWURO 8QLW (&8 KDV WKH DELOLW\ WR GLVSOD\ D FRGH 7KLV LQGLFDWHV WKH VWDUW RI EOLQNLQJ VWRUHG
'7&V XVLQJ EOLQNLQJ VHTXHQFH RI WKH IDXOW ODPS FRGHV ,I WKHUH DUH DQ\ VWRUHG '7&V WKH )DXOW /DPS
ZLOO IODVK LWV ±GLJLW QXPEHU ,I WKHUH LV PRUH WKDQ RQH
127( 7KH (&8 EOLQNV WKH FRGHV LQ GLJLW FRGHV VWRUHG '7& WKH (&8 ZLOO IODVK HDFK FRGH LQ QXPHULFDO
RQO\ 6HH /,67,1* 2) ',$*1267,& 7528%/( RUGHU ,I WKHUH DUH QR VWRUHG '7&V WKH )DXOW /DPS
&2'(6 '7&6 ODWHU LQ WKLV *URXS ZLOO IODVK D FRGH
3UHVV GRZQ 2YHUULGH 6KXWGRZQ 6ZLWFK ZKLOH WXUQLQJ 2QFH FRPSOHWH WKLV VHTXHQFH ZLOO UHSHDW
WKH LJQLWLRQ VZLWFK ´21´ :KHQ FRPSOHWH WXUQ LJQLWLRQ ´2))´
7KH )DXOW /DPS ZLOO EHJLQ WR IODVK D FRGH QXPEHU )RU $V DQ H[DPSOH LI DQ HQJLQH KDG DQ DFWLYH '7&
H[DPSOH IODVK WKUHH WLPHVVKRUW SDXVHIODVK WZR DQG VWRUHG '7& WKH IODVKLQJ VHTXHQFH ZRXOG EH
WLPHVORQJ SDXVH 7KLV H[DPSOH LV FRGH IODVK WKUHH WLPHVVKRUW SDXVHIODVK WZR WLPHVORQJ
7KH (&8 EHJLQV WKH IODVKLQJ VHTXHQFH E\ IODVKLQJ SDXVHIODVK RQH WLPHVKRUW SDXVHIODVK HLJKW
D FRGH WKLV LQGLFDWHV WKH VWDUW RI EOLQNLQJ DFWLYH WLPHVORQJ SDXVHIODVK WKUHH WLPHVVKRUW SDXVHIODVK
FRGHV ,I WKHUH DUH DQ\ DFWLYH '7&V WKH (&8 ZLOO IODVK WKUHH WLPHVORQJ SDXVHIODVK ILYH WLPHVVKRUW
LWV ±GLJLW QXPEHU ,I WKHUH LV PRUH WKDQ RQH DFWLYH SDXVHIODVK WKUHH WLPHV
'7& WKH (&8 ZLOO IODVK HDFK FRGH LQ QXPHULFDO RUGHU
&' )(%
31
7URXEOHVKRRWLQJ
31
7URXEOHVKRRWLQJ
31
7URXEOHVKRRWLQJ
31
7URXEOHVKRRWLQJ
5* ²81²0$<
$²&RRODQW 7HPSHUDWXUH 6HQVRU +²2LO 3UHVVXUH 6HQVRU 1²&$1 1HWZRUN 'LDJQRVWLF 6²)XHO +HDWHU &RQQHFWRU
&RQQHFWRU &RQQHFWRU &RQQHFWRU 7² 0DQLIROG $LU 7HPSHUDWXUH
%²)XHO 7HPSHUDWXUH 6HQVRU ,² 0DLQ 6\VWHP )XVH DPS 2²,QVWUXPHQW 3DQHO &RQQHFWRU 0$7 6HQVRU &RQQHFWRU
&RQQHFWRU -² 3RZHU DQG *URXQG %DWWHU\ +DUQHVV 8²$OWHUQDWRU ,JQLWLRQ &RQQHFWRU
&²,QMHFWLRQ 3XPS 6ROHQRLG &RQQHFWLRQV 3²SLQ 2SWLRQDO )HDWXUH 9²2SWLRQDO ,QVWUXPHQW 3DQHO RU
&RQQHFWRU .²)XVH +ROGHU &RQQHFWRU ([WHQGHGIHDWXUH *HQHUDWRU ,QVWUXPHQW 3DQHO
'²6$( &$1 &RQQHFWRU /² 7UDQVLHQW 9ROWDJH 3URWHFWLRQ (&8 RQO\
(²&UDQNVKDIW 3RVLWLRQ 6HQVRU 793 0RGXOH &RQQHFWRU 4²SLQ ,QVWUXPHQW 3DQHO
&RQQHFWRU 0²5HPRWH 21 2)) &RQQHFWRU &RQQHFWRU
)² (&8 &RQQHFWRU 5²(QJLQH :LULQJ +DUQHVV
*²6WDUWHU 5HOD\ &RQQHFWRU
&'( 0$<
31
7URXEOHVKRRWLQJ
(QJLQH :LULQJ /D\RXW RQ DQG (QJLQHV ² 'HQVR +LJK 3UHVVXUH &RPPRQ 5DLO
([FHSW +)*+)6+)8
5* ²81²-81
+)8 (QJLQH VKRZQ
$²(QJLQH &RRODQW 7HPSHUDWXUH '²(&8 &RQQHFWRU +²3RZHU DQG *URXQG %DWWHU\ /² 3XPS &RQWURO 9DOYH 6ROHQRLG
(&7 6HQVRU (²2SWLRQDO ,QVWUXPHQW 3DQHO RU &RQQHFWLRQV 0²)XHO 7HPSHUDWXUH 6HQVRU
%²(OHFWURQLF ,QMHFWRU &RQQHFWRU *HQHUDWRU ,QVWUXPHQW 3DQHO ,² )XHO 5DLO 3UHVVXUH 6HQVRU
&²0DQLIROG $LU 7HPSHUDWXUH )² (QJLQH :LULQJ +DUQHVV -² &UDQNVKDIW 3RVLWLRQ 6HQVRU
0$7 6HQVRU *²(QJLQH 2LO 3UHVVXUH 6HQVRU .²3XPS 3RVLWLRQ 6HQVRU
&RQQHFWRU
&') -81
31
7URXEOHVKRRWLQJ
(QJLQH :LULQJ /D\RXW DQG 6HQVRU /RFDWLRQ +)* +)6 DQG +)8
(QJLQHV
&' ²81²0$<
$²(QJLQH &RRODQW 7HPSHUDWXUH &²6XFWLRQ &RQWURO 9DOYH (²)XHO 7HPSHUDWXUH 6HQVRU
6HQVRU '²)XHO 5DLO 3UHVVXUH 6HQVRU )² /RZ 3UHVVXUH )XHO 3UHVVXUH
%²&UDQNVKDIW 3RVLWLRQ 6HQVRU 6HQVRU
&RQWLQXHG RQ QH[W SDJH &'& -81
31
7URXEOHVKRRWLQJ
&' ²81²0$<
*²&DPVKDIW 3RVLWLRQ 6HQVRU ,² (QJLQH &RQQHFWRU &LUFXLW -² 0DFKLQH &RQQHFWLRQ
+²(QJLQH &RQQHFWRU &LUFXLW
&RQWLQXHG RQ QH[W SDJH &'& -81
31
7URXEOHVKRRWLQJ
&' ²81²0$<
.²/RZ 3UHVVXUH )XHO 3XPS 0²(QJLQH 2LO 3UHVVXUH 6HQVRU 1²:DWHU ,Q )XHO 6HQVRU
/² 0DQLIROG $LU 7HPSHUDWXUH
6HQVRU
&'& -81
31
7URXEOHVKRRWLQJ
(QJLQH FUDQNV EXW ZLOO QRW VWDUW ,QFRUUHFW VWDUWLQJ SURFHGXUH 9HULI\ FRUUHFW VWDUWLQJ SURFHGXUH
)XHO ILOWHU SOXJJHG RU IXOO RI ZDWHU 5HSODFH IXHO ILOWHU RU GUDLQ ZDWHU IURP
ILOWHU
,QMHFWLRQ SXPS QRW JHWWLQJ IXHO RU DLU &KHFN IXHO IORZ DW VXSSO\ SXPS RU
LQ IXHO V\VWHP EOHHG IXHO V\VWHP
(QJLQH KDUG WR VWDUW RU ZLOO QRW VWDUW (QJLQH VWDUWLQJ XQGHU ORDG 5HPRYH ORDG
:DWHU GLUW RU DLU LQ IXHO V\VWHP 'UDLQ IOXVK ILOO DQG EOHHG V\VWHP
,QMHFWLRQ SXPS VKXWRII QRW UHVHW 7XUQ NH\ VZLWFK WR ´2))´ WKHQ WR ´21´
(QJLQH NQRFNV /RZ HQJLQH RLO OHYHO $GG RLO WR HQJLQH FUDQNFDVH
31
7URXEOHVKRRWLQJ
(QJLQH UXQV LUUHJXODUO\ RU VWDOOV /RZ FRRODQW WHPSHUDWXUH 5HPRYH DQG FKHFN WKHUPRVWDW
IUHTXHQWO\
&ORJJHG IXHO ILOWHU 5HSODFH IXHO ILOWHU HOHPHQW
:DWHU GLUW RU DLU LQ IXHO V\VWHP 'UDLQ IOXVK ILOO DQG EOHHG V\VWHP
%HORZ QRUPDO HQJLQH WHPSHUDWXUH 'HIHFWLYH WKHUPRVWDW 5HPRYH DQG FKHFN WKHUPRVWDW
31
7URXEOHVKRRWLQJ
+LJK RLO FRQVXPSWLRQ &UDQNFDVH RLO WRR OLJKW 8VH SURSHU YLVFRVLW\ RLO
(QJLQH HPLWV ZKLWH VPRNH ,PSURSHU W\SH RI IXHO 8VH SURSHU IXHO
(QJLQH HPLWV EODFN RU JUD\ H[KDXVW ,PSURSHU W\SH RI IXHO 8VH SURSHU IXHO
VPRNH
&ORJJHG RU GLUW\ DLU FOHDQHU 6HUYLFH DLU FOHDQHU
6WUHWFKHG SRO\ 9EHOW RU GHIHFWLYH EHOW &KHFN DXWRPDWLF EHOW WHQVLRQHU DQG
WHQVLRQHU FKHFN EHOWV IRU VWUHWFKLQJ 5HSODFH DV
UHTXLUHG
31
7URXEOHVKRRWLQJ
/RZ HQJLQH RLO OHYHO &KHFN RLO OHYHO $GG RLO DV UHTXLUHG
+LJK IXHO FRQVXPSWLRQ ,PSURSHU W\SH RI IXHO 8VH SURSHU W\SH RI IXHO
'36*&' 0$<
31
7URXEOHVKRRWLQJ
(OHFWULFDO WURXEOHVKRRWLQJ
6\PSWRP 3UREOHP 6ROXWLRQ
8QGHUFKDUJHG V\VWHP ([FHVVLYH HOHFWULFDO ORDG IURP DGGHG 5HPRYH DFFHVVRULHV RU LQVWDOO KLJKHU
DFFHVVRULHV RXWSXW DOWHUQDWRU
%DWWHU\ XVHV WRR PXFK ZDWHU &UDFNHG EDWWHU\ FDVH &KHFN IRU PRLVWXUH DQG UHSODFH DV
QHFHVVDU\
%DWWHULHV ZLOO QRW FKDUJH /RRVH RU FRUURGHG FRQQHFWLRQV &OHDQ DQG WLJKWHQ FRQQHFWLRQV
6WUHWFKHG SRO\ 9EHOW RU GHIHFWLYH EHOW $GMXVW EHOW WHQVLRQ RU UHSODFH EHOWV
WHQVLRQHU
6WDUWHU ZLOO QRW FUDQN (QJLQH XQGHU ORDG 5HPRYH ORDG
6WDUWHU FUDQNV VORZO\ /RZ EDWWHU\ RXWSXW 6HH \RXU DXWKRUL]HG VHUYLFLQJ GHDOHU
RU HQJLQH GLVWULEXWRU
(QWLUH HOHFWULFDO V\VWHP )DXOW\ EDWWHU\ FRQQHFWLRQ &OHDQ DQG WLJKWHQ FRQQHFWLRQV
31
7URXEOHVKRRWLQJ
'36*&' -$1
31
6WRUDJH
(QJLQH VWRUDJH JXLGHOLQHV
-RKQ 'HHUH HQJLQHV FDQ EH VWRUHG RXWVLGH IRU XS WR -RKQ 'HHUH HQJLQHV FDQ EH VWRUHG LQVLGH ZDUHKRXVHG
WKUHH PRQWKV ZLWK QR ORQJ WHUP SUHSDUDWLRQ ,) IRU XS WR VL[ PRQWKV ZLWK QR ORQJ WHUP SUHSDUDWLRQ
&29(5(' %< :$7(53522) &29(5,1*
-RKQ 'HHUH HQJLQHV H[SHFWHG WR EH VWRUHG PRUH WKDQ
-RKQ 'HHUH HQJLQHV FDQ EH VWRUHG LQ D VWDQGDUG VL[ PRQWKV ORQJ WHUP VWRUDJH SUHSDUDWLRQ 0867
RYHUVHDV VKLSSLQJ FRQWDLQHU IRU XS WR WKUHH PRQWKV %( WDNHQ 6HH 3UHSDUH (QJLQH IRU /RQJ 6WRUDJH
ZLWK QR ORQJ WHUP SUHSDUDWLRQ
'36*&' 0$<
,03257$17 $Q\ WLPH \RXU HQJLQH ZLOO QRW EH 5HPRYH IDQDOWHUQDWRU EHOW LI GHVLUHG
XVHG IRU RYHU VL[ PRQWKV WKH IROORZLQJ 5HPRYH DQG FOHDQ EDWWHULHV 6WRUH WKHP LQ D FRRO GU\
UHFRPPHQGDWLRQV IRU VWRULQJ LW DQG UHPRYLQJ SODFH DQG NHHS WKHP IXOO\ FKDUJHG
LW IURP VWRUDJH ZLOO KHOS WR PLQLPL]H
FRUURVLRQ DQG GHWHULRUDWLRQ &OHDQ WKH H[WHULRU RI WKH HQJLQH ZLWK VDOWIUHH ZDWHU
DQG WRXFK XS DQ\ VFUDWFKHG RU FKLSSHG SDLQWHG
&KDQJH HQJLQH RLO DQG UHSODFH ILOWHU 8VHG RLO ZLOO QRW VXUIDFHV ZLWK D JRRG TXDOLW\ SDLQW
JLYH DGHTXDWH SURWHFWLRQ 6HH &KDQJH (QJLQH 2LO
&RDW DOO H[SRVHG PDFKLQHG PHWDO VXUIDFHV ZLWK
DQG )LOWHU
JUHDVH RU FRUURVLRQ LQKLELWRU LI QRW IHDVLEOH WR SDLQW
6HUYLFH DLU FOHDQHU 6HH &OHDQ $LU )LOWHU (OHPHQW
6HDO DOO RSHQLQJV RQ HQJLQH ZLWK SODVWLF EDJV DQG WDSH
'UDLQLQJ DQG IOXVKLQJ RI FRROLQJ V\VWHP LV QRW
6WRUH WKH HQJLQH LQ D GU\ SURWHFWHG SODFH ,I HQJLQH
QHFHVVDU\ LI HQJLQH LV WR EH VWRUHG RQO\ IRU VHYHUDO
PXVW EH VWRUHG RXWVLGH FRYHU LW ZLWK D ZDWHUSURRI
PRQWKV +RZHYHU IRU H[WHQGHG VWRUDJH SHULRGV RI
FDQYDV RU RWKHU VXLWDEOH SURWHFWLYH PDWHULDO DQG XVH
D \HDU RU ORQJHU LW LV UHFRPPHQGHG WKDW WKH FRROLQJ
D VWURQJ ZDWHUSURRI WDSH
V\VWHP EH GUDLQHG IOXVKHG DQG UHILOOHG 5HILOO ZLWK
'36*&' 0$<
31
6SHFLILFDWLRQV
*HQHUDO HQJLQH SDFN VSHFLILFDWLRQV
1RQ(PLVVLRQ &HUWLILHG (QJLQHV
,7(0 81,7 2) ') ') &'')6 &'')8 7)
0($685(
1XPEHU RI
&\OLQGHUV
)XHO 'LHVHO 'LHVHO 'LHVHO 'LHVHO 'LHVHO
%RUH PP
6WURNH PP
'LVSODFHPHQW /
&RPSUHVVLRQ 5DWLR
32:(5D # N: KS
USP 3ULPH
32:(5D # N: KS
USP 6WDQGE\
32:(5D # N: KS
USP 3ULPH
32:(5D # N: KS
USP 6WDQGE\
:LGWK RYHUDOO PP
/HQJWK RYHUDOO PP
+HLJKW RYHUDOO PP
:HLJKW GU\E NJ
(QJLQH RLO TXDQWLW\ /
(QJLQH FRRODQW /
TXDQWLW\
D
:LWK )DQ
E
$SSUR[LPDWH
31
6SHFLILFDWLRQV
D
:LWK )DQ
E
$SSUR[LPDWH
D
:LWK )DQ
E
$SSUR[LPDWH
31
6SHFLILFDWLRQV
D
:LWK )DQ
E
$SSUR[LPDWH
,7(0 81,7 2) 0($685( +)* +)6 +)8
1XPEHU RI &\OLQGHUV
)XHO 'LHVHO 'LHVHO 'LHVHO
%RUH PP
6WURNH PP
'LVSODFHPHQW /
&RPSUHVVLRQ 5DWLR
32:(5D # USP N: KS
3ULPH
32:(5D # USP N: KS
6WDQGE\
32:(5D # USP N: KS
3ULPH
32:(5D # USP N: KS
6WDQGE\
:LGWK RYHUDOO PP
/HQJWK RYHUDOO PP
+HLJKW RYHUDOO PP
E NJ
:HLJKW GU\
(QJLQH RLO TXDQWLW\ /
(QJLQH FRRODQW TXDQWLW\ F
/ ² ²
D
:LWK )DQ
E
$SSUR[LPDWH
F
,QFOXGLQJ 5DGLDWRU
&') 6(3
31
6SHFLILFDWLRQV
D
:LWK )DQ
E
$SSUR[LPDWH
,7(0 81,7 2) 0($685( +)6 +)6 +)8
1XPEHU RI &\OLQGHUV
)XHO 'LHVHO 'LHVHO 'LHVHO
%RUH PP
6WURNH PP
'LVSODFHPHQW /
&RPSUHVVLRQ 5DWLR
32:(5D # USP N: KS
3ULPH
32:(5D # USP N: KS
6WDQGE\
32:(5D # USP N: KS
3ULPH
32:(5D # USP N: KS
6WDQGE\
:LGWK RYHUDOO PP
/HQJWK RYHUDOO PP
+HLJKW RYHUDOO PP
E NJ
:HLJKW GU\
(QJLQH RLO TXDQWLW\ /
(QJLQH FRRODQW TXDQWLW\ /
D
:LWK )DQ
E
$SSUR[LPDWH
,7(0 81,7 2) 0($685( +)8 7)6 7)8
1XPEHU RI &\OLQGHUV
31
6SHFLILFDWLRQV
D
:LWK )DQ
E
$SSUR[LPDWH
,7(0 81,7 2) 0($685( +)6 +)6 +)6 +)6
1XPEHU RI &\OLQGHUV
)XHO 'LHVHO 'LHVHO 'LHVHO 'LHVHO
%RUH PP
6WURNH PP
'LVSODFHPHQW /
&RPSUHVVLRQ 5DWLR
32:(5D # USP N: KS
3ULPH
32:(5D # USP N: KS
6WDQGE\
32:(5D # USP N: KS
3ULPH
32:(5D # USP N: KS
6WDQGE\
:LGWK RYHUDOO PP
/HQJWK RYHUDOO PP
+HLJKW RYHUDOO PP
E NJ
:HLJKW GU\
(QJLQH RLO TXDQWLW\ /
(QJLQH FRRODQW TXDQWLW\ /
D
:LWK )DQ
E
$SSUR[LPDWH
,7(0 81,7 2) 0($685( +)8 +)8 +)8
1XPEHU RI &\OLQGHUV
)XHO 'LHVHO 'LHVHO 'LHVHO
%RUH PP
6WURNH PP
'LVSODFHPHQW /
&RQWLQXHG RQ QH[W SDJH &') 6(3
31
6SHFLILFDWLRQV
D
:LWK )DQ
E
$SSUR[LPDWH
&') 6(3
D
:LWK )DQ
E
$SSUR[LPDWH
&'' -8/
31
6SHFLILFDWLRQV
D
:LWK )DQ
E
$SSUR[LPDWH
,7(0 81,7 2) 0($685( +)6 +)6 +)6
1XPEHU RI &\OLQGHUV
)XHO 'LHVHO 'LHVHO 'LHVHO
%RUH PP
6WURNH PP
'LVSODFHPHQW /
&RPSUHVVLRQ 5DWLR
32:(5D # USP N: KS
3ULPH
32:(5D # USP N: KS
6WDQGE\
32:(5D # USP N: KS
3ULPH
32:(5D # USP N: KS
6WDQGE\
:LGWK RYHUDOO PP
/HQJWK RYHUDOO PP
+HLJKW RYHUDOO PP
E NJ
:HLJKW GU\
(QJLQH RLO TXDQWLW\ /
(QJLQH FRRODQW TXDQWLW\ /
D
:LWK )DQ
E
$SSUR[LPDWH
&'' -8/
31
6SHFLILFDWLRQV
%ROW RU 6FUHZ 6$( *UDGH 6$( *UDGH D 6$( *UDGH RU 6$( *UDGH RU
E F E F E F
6L]H /XEULFDWHG 'U\ /XEULFDWHG 'U\ /XEULFDWHG 'U\ /XEULFDWHGE 'U\F
1ÂP OELQ 1ÂP OELQ 1ÂP OELQ 1ÂP OELQ 1ÂP OELQ 1ÂP OELQ 1ÂP OELQ 1ÂP OELQ
1ÂP OEIW 1ÂP OEIW
1ÂP OEIW 1ÂP OEIW
1ÂP OEIW 1ÂP OEIW 1ÂP OEIW
1ÂP OEIW
7RUTXH YDOXHV OLVWHG DUH IRU JHQHUDO XVH RQO\ EDVHG RQ WKH VWUHQJWK RI WKH EROW 5HSODFH IDVWHQHUV ZLWK WKH VDPH RU KLJKHU JUDGH ,I KLJKHU
RU VFUHZ '2 127 XVH WKHVH YDOXHV LI D GLIIHUHQW WRUTXH YDOXH RU WLJKWHQLQJ JUDGH IDVWHQHUV DUH XVHG WLJKWHQ WKHVH WR WKH VWUHQJWK RI WKH
SURFHGXUH LV JLYHQ IRU D VSHFLILF DSSOLFDWLRQ )RU SODVWLF LQVHUW RU FULPSHG VWHHO RULJLQDO 0DNH VXUH IDVWHQHU WKUHDGV DUH FOHDQ DQG WKDW \RX
W\SH ORFN QXWV IRU VWDLQOHVV VWHHO IDVWHQHUV RU IRU QXWV RQ 8EROWV VHH WKH SURSHUO\ VWDUW WKUHDG HQJDJHPHQW :KHQ SRVVLEOH OXEULFDWH
WLJKWHQLQJ LQVWUXFWLRQV IRU WKH VSHFLILF DSSOLFDWLRQ 6KHDU EROWV DUH GHVLJQHG WR IDLO SODLQ RU ]LQF SODWHG IDVWHQHUV RWKHU WKDQ ORFN QXWV ZKHHO EROWV
XQGHU SUHGHWHUPLQHG ORDGV $OZD\V UHSODFH VKHDU EROWV ZLWK LGHQWLFDO JUDGH RU ZKHHO QXWV XQOHVV GLIIHUHQW LQVWUXFWLRQV DUH JLYHQ IRU WKH
VSHFLILF DSSOLFDWLRQ
D
*UDGH DSSOLHV IRU KH[ FDS VFUHZV QRW KH[ EROWV XS WR LQ PP ORQJ *UDGH DSSOLHV IRU KH[ FDS VFUHZV RYHU
LQ PP ORQJ DQG IRU DOO RWKHU W\SHV RI EROWV DQG VFUHZV RI DQ\ OHQJWK
E
³/XEULFDWHG´ PHDQV FRDWHG ZLWK D OXEULFDQW VXFK DV HQJLQH RLO IDVWHQHUV ZLWK SKRVSKDWH DQG RLO FRDWLQJV RU LQ
DQG ODUJHU IDVWHQHUV ZLWK -'0 )& )) RU )- ]LQF IODNH FRDWLQJ
F
³'U\´ PHDQV SODLQ RU ]LQF SODWHG ZLWKRXW DQ\ OXEULFDWLRQ RU WR LQ IDVWHQHUV ZLWK -'0 )% )( RU )+ ]LQF IODNH FRDWLQJ
';7254 -$1
31
6SHFLILFDWLRQV
%ROW RU 6FUHZ &ODVV &ODVV RU &ODVV &ODVV
6L]H /XEULFDWHGD 'U\E /XEULFDWHGD 'U\E /XEULFDWHGD 'U\E /XEULFDWHGD 'U\E
1ÂP OELQ 1ÂP OELQ 1ÂP OELQ 1ÂP OELQ 1ÂP OELQ 1ÂP OELQ 1ÂP OELQ 1ÂP OELQ
0
1ÂP OEIW 1ÂP OEIW 1ÂP OEIW 1ÂP OEIW
0
1ÂP OEIW 1ÂP OEIW 1ÂP OEIW
0
1ÂP OEIW
0
0
0
0
0
0
0
0
0
0
0
7RUTXH YDOXHV OLVWHG DUH IRU JHQHUDO XVH RQO\ EDVHG RQ WKH VWUHQJWK RI 6KHDU EROWV DUH GHVLJQHG WR IDLO XQGHU SUHGHWHUPLQHG ORDGV $OZD\V
WKH EROW RU VFUHZ '2 127 XVH WKHVH YDOXHV LI D GLIIHUHQW WRUTXH YDOXH RU UHSODFH VKHDU EROWV ZLWK LGHQWLFDO SURSHUW\ FODVV 5HSODFH IDVWHQHUV ZLWK
WLJKWHQLQJ SURFHGXUH LV JLYHQ IRU D VSHFLILF DSSOLFDWLRQ )RU VWDLQOHVV VWHHO WKH VDPH RU KLJKHU SURSHUW\ FODVV ,I KLJKHU SURSHUW\ FODVV IDVWHQHUV DUH
IDVWHQHUV RU IRU QXWV RQ 8EROWV VHH WKH WLJKWHQLQJ LQVWUXFWLRQV IRU WKH XVHG WLJKWHQ WKHVH WR WKH VWUHQJWK RI WKH RULJLQDO 0DNH VXUH IDVWHQHU
VSHFLILF DSSOLFDWLRQ 7LJKWHQ SODVWLF LQVHUW RU FULPSHG VWHHO W\SH ORFN QXWV WKUHDGV DUH FOHDQ DQG WKDW \RX SURSHUO\ VWDUW WKUHDG HQJDJHPHQW :KHQ
E\ WXUQLQJ WKH QXW WR WKH GU\ WRUTXH VKRZQ LQ WKH FKDUW XQOHVV GLIIHUHQW SRVVLEOH OXEULFDWH SODLQ RU ]LQF SODWHG IDVWHQHUV RWKHU WKDQ ORFN QXWV
LQVWUXFWLRQV DUH JLYHQ IRU WKH VSHFLILF DSSOLFDWLRQ ZKHHO EROWV RU ZKHHO QXWV XQOHVV GLIIHUHQW LQVWUXFWLRQV DUH JLYHQ IRU WKH
VSHFLILF DSSOLFDWLRQ
D
³/XEULFDWHG´ PHDQV FRDWHG ZLWK D OXEULFDQW VXFK DV HQJLQH RLO IDVWHQHUV ZLWK SKRVSKDWH DQG RLO FRDWLQJV RU 0
DQG ODUJHU IDVWHQHUV ZLWK -'0 )& )) RU )- ]LQF IODNH FRDWLQJ
E
³'U\´ PHDQV SODLQ RU ]LQF SODWHG ZLWKRXW DQ\ OXEULFDWLRQ RU 0 WR 0 IDVWHQHUV ZLWK -'0 )% )( RU )+ ]LQF IODNH FRDWLQJ
';7254 -$1
31
6SHFLILFDWLRQV
31
,QGH[
3DJH
3DJH
$
9LHZ VWRUHG VHUYLFH FRGHV
$LU ILOWHU
&KHFN (
&OHDQ RU UHSODFH RQHSLHFH
&OHDQ RU UHSODFH HOHPHQW (QJLQH
$LU LQWDNH V\VWHP 2SHUDWLRQ
&KHFNLQJ (QJLQH &RQWURO 8QLW (&8 VHULDO QXPEHU
(QJLQH RLO
% %UHDN,Q
1RQ(PLVVLRQV FHUWLILHG DQG FHUWLILHG
%DWWHU\ +DQGOLQJ 6DIHW\ WLHU WLHU WLHU VWDJH , VWDJH ,,
6DIHW\ %DWWHU\ +DQGOLQJ DQG VWDJH ,,,
%HOW 'LHVHO
&KHFN DXWRPDWLF WHQVLRQHU 1RQ(PLVVLRQV FHUWLILHG DQG FHUWLILHG
&KHFN WHQVLRQ WLHU DQG VWDJH ,
5HSODFH DQG HQJLQHV ZLWK (QJLQH VSHHG 0HFKDQLFDO IXHO V\VWHP
DXWRPDWLF WHQVLRQHU (QJLQH ZLULQJ OD\RXW
%ROW DQG VFUHZ WRUTXH YDOXHV DQG (QJLQHV :LWK 'HQVR
0HWULF +LJK 3UHVVXUH &RPPRQ 5DLO ([FHSW
8QLILHG LQFK +)*+)6+)8
%UHDNLQ HQJLQH RLO :LWK 6WDQDG\QH '( SXPS
1RQ(PLVVLRQV FHUWLILHG DQG FHUWLILHG WLHU (QJLQH :LULQJ /D\RXW DQG 6HQVRU
WLHU WLHU VWDJH , VWDJH ,, DQG VWDJH ,,, /RFDWLRQ +)* +)6 DQG
+)8 (QJLQHV
&
)
&RQILJXUDWLRQ GDWD YLHZLQJ
&RRODQW )XHO
'LHVHO HQJLQH 'LHVHO
(QJLQH ZLWK ZHW VOHHYH F\OLQGHU OLQHUV +DQGOLQJ DQG VWRULQJ
3UHVVXUH WHVWLQJ FRROLQJ V\VWHP )XHO ILOWHU
6XSSOHPHQWDO DGGLWLYHV &KHFN
:DUP WHPSHUDWXUH FOLPDWHV )XHO SXPS PRGHO QXPEHU
&RRODQW OHYHO )XHO V\VWHP
&KHFN %OHHGLQJ
&UDQNFDVH YHQW WXEH
&OHDQLQJ +
,QGH[
31
,QGH[
3DJH 3DJH
0DLQWHQDQFH 2
KRXUV \HDU
&KHFN DQG DGMXVW YDOYH FOHDUDQFH 2LO
DQG HQJLQHV (QJLQH
&KHFNLQJ DLU LQWDNH V\VWHP 1RQ(PLVVLRQV FHUWLILHG DQG FHUWLILHG
&KHFNLQJ DXWRPDWLF EHOW WHQVLRQHU WLHU DQG VWDJH ,
DQG (QJLQHV 2LO OHYHO
&OHDQLQJ FUDQNFDVH YHQW WXEH &KHFN
3UHVVXUH WHVWLQJ FRROLQJ V\VWHP 2SHUDWLQJ WKH HQJLQH
5HSODFH &UDQNFDVH 9HQW )LOWHU 2SWLRQDO %UHDNLQ SHULRG
KRXUV \HDUV &KDQJLQJ *HQHUDWRU )UHTXHQF\
$GMXVW VSHHG GURRS JRYHUQRU 6WDQGE\ SRZHU XQLWV
0HFKDQLFDO IXHO V\VWHP 6WDUWLQJ WKH HQJLQH
$GMXVW YDOYH FOHDUDQFH DQG 6WRSSLQJ WKH HQJLQH
HQJLQHV 8VLQJ D ERRVWHU EDWWHU\ RU FKDUJHU
&KHFN HQJLQH VSHHG 0HFKDQLFDO IXHO V\VWHP
'DPSHU FKHFN 3
KRXUV \HDUV
'UDLQ DQG )OXVK &RROLQJ 6\VWHP 3URSRVLWLRQ
+RXUV
&KDQJH (QJLQH 2LO DQG )LOWHU DQG 6
(QJLQHV
&KDQJH (QJLQH 2LO DQG )LOWHU 6DIHW\ $YRLG +LJK3UHVVXUH )OXLGV
+)* +)6 DQG $YRLG +LJK3UHVVXUH )OXLGV
+)8 (QJLQHV 6DIHW\ +DQGOH )XHO 6DIHO\ $YRLG )LUHV
&KDQJH (QJLQH 2LO DQG )LOWHU RQ $YRLG )LUHV +DQGOH )XHO 6DIHO\
DQG (QJLQHV ([FHSW 6DIHW\ 6WHSV DQG +DQGKROGV
+)*+)6+)8 8VH 6WHSV DQG +DQGKROGV &RUUHFWO\
&KDQJH )XHO )LOWHU (OHPHQW DQG 6HULDO QXPEHU
(QJLQHV (QJLQH &RQWURO 8QLW (&8
&KDQJH )XHO )LOWHU (OHPHQWV +LJKSUHVVXUH IXHO SXPS
+)* +)6 DQG 6HULDO QXPEHUV
+)8 (QJLQHV (QJLQH &RQWURO 8QLW (&8 VHULDO QXPEHU
&KDQJH )XHO )LOWHU (OHPHQWV RQ (QJLQH RSWLRQ FRGHV
DQG (QJLQHV ([FHSW (QJLQH VHULDO QXPEHU SODWH
+)*+)6+)8 )XHO SXPS PRGHO QXPEHU
&KHFNLQJ EHOW 32:(57HFK ODEHO
$V UHTXLUHG 5HFRUG HQJLQH VHULDO QXPEHU
$GGLWLRQDO VHUYLFH LQIRUPDWLRQ 5HFRUG IXHO LQMHFWLRQ SXPS PRGHO QXPEHU
%OHHG WKH IXHO V\VWHP 6SHFLILFDWLRQV
&OHDQ RU UHSODFH DLU ILOWHU RQHSLHFH (QJLQH 3DFN
&OHDQ RU UHSODFH DLU ILOWHU HOHPHQW (3$ 7LHU (PLVVLRQ &HUWLILHG (QJLQHV
'R QRW PRGLI\ IXHO V\VWHP (3$ 7LHU (PLVVLRQ &HUWLILHG (QJLQHV
5HSODFH IDQ DQG DOWHUQDWRU EHOWV 1RQ(PLVVLRQ &HUWLILHG (QJLQHV
DQG HQJLQHV ZLWK DXWRPDWLF WHQVLRQHU 6WDJH ,, (PLVVLRQ &HUWLILHG (QJLQHV
,QGH[
31
,QGH[
3DJH 3DJH
7RUTXH FKDUWV :
0HWULF
8QLILHG LQFK :LULQJ KDUQHVV
7URXEOH FRGHV DQG (QJLQHV :LWK 'HQVR
7URXEOHVKRRWLQJ +LJK 3UHVVXUH &RPPRQ 5DLO ([FHSW
(OHFWULFDO +)*+)6+)8
(QJLQH :LWK 6WDQDG\QH '( SXPS
*HQHUDO LQIRUPDWLRQ
8
8QLILHG LQFK EROW DQG VFUHZ WRUTXH YDOXHV
,QGH[
31
,QGH[
,QGH[
31
User guide and maintenance manual
KOHLER
Alternator
18/07/2017 33521036201_3_1
MUE 33521036201_3_1
CONTENTS
1 Preface.......................................................................................................................................................................................... 2
1.1 General guidelines ............................................................................................................................................................... 2
1.2 Instructions and safety regulations (personal protection).....................................................................................................2
2 Applicable directives and standards.............................................................................................................................................. 2
3 Specifications ................................................................................................................................................................................ 3
3.1 Mass..................................................................................................................................................................................... 3
4 Maintenance.................................................................................................................................................................................. 4
4.1 General checking of the installation ..................................................................................................................................... 4
4.2 Cleaning the alternator ......................................................................................................................................................... 4
4.3 Checking the ventilation circuit............................................................................................................................................. 4
4.4 Checking bearings................................................................................................................................................................ 5
4.4.1 Bearings lubricated for life ............................................................................................................................................... 5
4.4.2 Regreasable bearings...................................................................................................................................................... 5
4.5 Checking the winding ........................................................................................................................................................... 5
4.6 Maintenance of the regulator................................................................................................................................................ 6
4.6.1 Access to complete regulators manuals .......................................................................................................................... 6
4.6.2 Presentation of the regulator............................................................................................................................................ 6
4.6.3 Setting the regulator......................................................................................................................................................... 7
5 Repairing faults ............................................................................................................................................................................. 8
5.1 Intervention of the protections .............................................................................................................................................. 8
5.2 Explanation of the regulator LED flashing sequences..........................................................................................................8
5.3 Faults.................................................................................................................................................................................... 9
The various operations described in this manual are accompanied by recommendations or symbols to alert the user to the potential
risk of accidents. It is vital that you understand and take notice of the different warning symbols used.
Immediate danger.
Indicates an imminent danger which may result in death or serious injury. Failure to follow the instruction
shown may pose serious risks to the health and life of those concerned.
DANGER
Potential danger.
Indicates a dangerous situation if the warning is not heeded. Failure to follow the instruction indicated may
cause minor injuries to those concerned or damage to equipment.
IMPORTANT
Note : The manufacturer reserves the right to modify the characteristics of its products at any time to incorporate the latest
technological developments. The information contained in this document are subject to change without previous notice.
RISK OF INJURY.
During operation, do not allow anyone to stand in front of the air outlet guards, in case anything is ejected from
them.
Do not allow children younger than 14 to go near the air outlet guards.
IMPORTANT
RISK OF BURN.
Never touch the alternator during operation or immediately after the stopping of the unit because some surface
parts might still be very hot.
IMPORTANT
STANDARDS:
- EN and IEC 60034 – 1 "Rotating electrical machines - Part 1: Rating and Performance"
3.1 Mass
Alternator KH00260T KH00350T KH00404T KH00420T KH00422T KH00460T KH00470T KH00500T KH00520T
Total (kg) 65 79 115 88 180 136 93 195 136
Alternator KH00620T KH00630T KH00771T KH00930T KH00941T KH00970T KH00973T KH01030T KH01180T
Total (kg) 225 162 250 510 290 300 300 560 590
Alternator KH01380T KH01720T KH02211T KH02970T KH02950T KH03543T KH01483T KH01982T KH02712T
Total (kg) 680 765 905 1870 1586 1693 1040 1171 1380
Alternator KH02953T KH03450T KH03543T KH03544T KH03850T KH03860T KH04070T KH04590T KH04830T
Total (kg) 1586 2090 1693 1693 3010 2275 2395 3380 2660
- Ensure that air flow is not reduced by partial blocking of the suction and discharge grids: mud, fiber, grease, etc ...
- Check for corrosion or abrasion grids air outlet.
If your system is equipped with filters:
- Remove the grid and remove the filter.
- Clean the filter with low pressure compressed air or replace if it is clogged.
.
Air inlet
Filter
Support
CAUTION
After prolonger storage or if the machines show signs of condensation, it is necessary to do an insulation check :
- Check the insulation resistance of all windings towards grounds, including the rotor. This measurement can be carried out
with a “Megger” device, or similar, with a 500V direct-current voltage.
- If the measured values are less than that required, warm up windings by blowing hot air of about 50-60°C.
DSR
DER 1 DER 2
Check that all connections, the position of the encoder, the straps and add-ons are repositioned identically than the initial regulator.
During normal operation and a duty cycle of 50% an indicator light mounted on the board flashes every 2 seconds; it flashes
differently in the event of intervention or alarm 1 ( see section ‘Meaning of LED flash regulator’).
The Hz trimmer allows to calibrate the threshold of the intervention of the under frequency protection up to -20% with respect to the
nominal speed value set by jumper 50/60 (at 50 Hz the threshold can be calibrated from 40 Hz to 50 Hz, at 60 Hz the threshold can
be calibrated from 48 Hz to 60 Hz).
The intervention of this protection reduce the output generator voltage and, to calibrate it, use the following procedure :
Rotate the Hz trimmer entirely in the counter clockwise direction.
1. If the machine has to operate at 60 Hz, ensure that the bridge is inserted between
a. DSR : terminals 12 and 13 of the CN1 connector.
b. DER : terminals 25 and 26.
2. Bring the generator to 90% of the nominal speed.
3. Slowly turn the “Hz” trimmer, by rotating it clockwise until the generator voltage begins to drop and ascertain that the
indicator light simultaneously begins flashing rapidly.
4. By increasing speed, the generator voltage will normalise and the alarm will disappear.
5. Set the speed to the nominal value.
When working on the rotating diodes, the excitation (induced, inductors) or the main field, contact an
authorized dealer.
IMPORTANT
LED
SHORT CIRCUIT
Amp
Hz or O.S.
STOP
Alarm intervention
T (s)
Blown fusible - Check the connection cables using the attached diagrams.
Alternator does not - Increase speed by 15%.
Residual voltage too low
excite - For an instant apply on the electronic regulator a 12 V battery voltage with a
No residual voltage
30Ω resistor in series respecting the polarities.
After being excited Faulty connection - Check connection cables as per attached drawings.
alternator does not
excite
Faulty setting - Calibrate the voltage using the special potentiometer.
Low speed - Check the number of turns.
Low voltage at no load (possible safety device activation)
Damaged windings - Check the windings.
Faulty setting - Calibrate the voltage using the special potentiometer.
High voltage at no - Check the regulator and replace it if necessary.
Faulty regulator
load
Faulty setting - Calibrate the voltage using the special potentiometer.
Load too high - Current too high, cosφ lower than 0.8, speed lower than 4% of the rated
At load conditions, value.
voltage lower than (possible safety device activation)
rated value - Check the regulator and replace it if necessary.
Faulty regulator
- Disconnect the cables and check the diodes; replace them if necessary.
Faulty diodes
At load conditions, Faulty setting - Calibrate the voltage using the special potentiometer.
voltage higher than Faulty regulator - Check the regulator and replace it if necessary.
rated voltage
Unstable speed - Check that rotation is uniform.
Unstable voltage Faulty setting - Regulate the stability of the regulator with the "STAB" potentiometer.