Beruflich Dokumente
Kultur Dokumente
Terminal Blocks
FREE Videos:
www.automationdirect.com/videos
FREE Documentation:
www.automationdirect.com/documentation
In this interactive PDF you can:
FREE CAD drawings:
• Use bookmarks to navigate by www.automationdirect.com/cad
product category
DINnectors Full-featured
Terminal Blocks
DINnectors provide a means of connecting
* UL rating for
copper wire and identifying two or more wires within the
only demands of an industrial environment.
DINnectors can terminate solid or stranded
wires ranging from 24 to 3/0 AWG (18 to
3/0 for CSA), and offer fusing, grounding or
disconnecting capability within the terminal
block itself.
Most DINnectors are modular in design, so
you can mix as many combinations of types,
wire-sizes and quantities as can fit on the uni-
versal DIN rail.
Our range of DINnectors terminal blocks is
internationally approved by various national
and international standards organizations
such as UL, CSA, VDE, SEV, RINA and IEC.
Terminal block
10 AWG
$0.25
KN-T10GRY
$3.16 $1.23
1492-W6 30 04 36 2
Three-level
terminal block
$1.25 $9.36 $9.50 terminal blocks and accessories
KN-TL14 1492-WTF3 27 15 97 9
* sold in 1m lengths
** Prices shown are per each, sold in packaged quantities
Prices may vary by dealer. Many other part numbers are available from all vendors. All prices are U.S. published prices. AutomationDirect prices as of 4/27/2016.
A-B prices from www.wernerelectric.com 4/18/2016. Phoenix Contact prices from www.mouser.com 4/18/2016.
Konnect-It® Component
Family Overview
Terminal Blocks Accessories
Single-Level Terminal Blocks End Brackets
Single-level terminal blocks can handle cur- End brackets prevent terminal blocks
rents up to 175A, can accept a wide range of and other DIN rail mounted compo-
wiring sizes from 26 AWG to 2/0 AWG and nents and devices from sliding along the
have a 100kA SCCR rating. Single-level termi- rail. They are available in configurations
nal blocks are available in a variety of colors. for 35mm and 15mm DIN rails.
online file usage Group D KN-T12BRN 100 $22.00 KN-T10BRN 100 $25.00 KN-T8BRN 100 $49.00
Brown
KN-T12BRN-25 25 $6.00 KN-T10BRN-25 25 $6.50 KN-T8BRN-25 25 $13.50
KN-T12BLK 100 $22.00 KN-T10BLK 100 $25.00 KN-T8BLK 100 $49.00
Black
Dimensions: mm [in] KN-T12BLK-25 25 $6.00 KN-T10BLK-25 25 $6.50 KN-T8BLK-25 25 $13.50
KN-T12GRN 100 $22.00 KN-T10GRN 100 $25.00 KN-T8GRN 100 $49.00
Green
KN-T12GRN-25 25 $6.00 KN-T10GRN-25 25 $6.50 KN-T8GRN-25 25 $13.50
KN-T12ORG 100 $22.00 KN-T10ORG 100 $25.00 KN-T8ORG 100 $49.00
Orange
KN-T12ORG-25 25 $6.00 KN-T10ORG-25 25 $6.50 KN-T8ORG-25 25 $13.50
KN-T12RED 100 $22.00 KN-T10RED 100 $25.00 KN-T8RED 100 $49.00
Red
KN-T12RED-25 25 $6.00 KN-T10RED-25 25 $6.50 KN-T8RED-25 25 $13.50
KN-T12YEL 100 $22.00 KN-T10YEL 100 $25.00 KN-T8YEL 100 $49.00
Yellow
KN-T12YEL-25 25 $6.00 KN-T10YEL-25 25 $6.50 KN-T8YEL-25 25 $13.50
See our website: www.AutomationDirect.com KN-T12WHT 100 $22.00 KN-T10WHT 100 $25.00 KN-T8WHT 100 $49.00
White
for complete engineering drawings KN-T12WHT-25 25 $6.00 KN-T10WHT-25 25 $6.50 KN-T8WHT-25 25 $13.50
Technical Specifications
Model KN-T12 KN-T10 KN-T8
Width 5mm [0.20 in] 6mm [0.24 in] 8mm [0.31 in]
Stripping Length 10mm [0.39 in] 10mm [0.39 in] 12mm [0.47 in]
Tightening Torque 0.4 N·m [3.5 lb·in] 0.5 N·m [4.4 lb·in] 0.8 N·m [7.1 lb·in]
Density 200/m [60 pcs/ft] 166/m [50 pcs/ft] 125/m [38 pcs/ft]
UL/CSA Approval 600V 20A 26-12 AWG *300V 30A 26-10 AWG *300V 50A 26-8 AWG
VDE Approval 750V 24A 2.5 mm² 750V 32A 4mm² 630V 41A 6mm²
CE Conformity 750V 24A 2.5 mm² 750V 32A 4mm² 630V 41A 6mm²
SCCR Rating 100kA 100kA 100kA
Operating Temperature Ambient air temperature: -67°F to 185°F [-55°C to 85°C], Relative humidity: 50% max at 104°F [40°C] and 90% max at 68°F [20°C]
Material Current Bar: Copper Alloy / Housing: Polyamide 66 / Screw: Zinc Plated Steel
DIN Rail Width 35mm
Accessories
KN-ECT6GRY 100/pkg $16.00 KN-ECT6GRY 100/pkg $16.00 KN-ECT6GRY 100/pkg $16.00
Gray
KN-ECT6GRY-25 25/pkg $4.00 KN-ECT6GRY-25 25/pkg $4.00 KN-ECT6GRY-25 25/pkg $4.00
Blue KN-ECT6BLU KN-ECT6BLU KN-ECT6BLU
Brown KN-ECT6BRN KN-ECT6BRN KN-ECT6BRN
End Covers Black KN-ECT6BLK KN-ECT6BLK KN-ECT6BLK
(International colors) Green KN-ECT6GRN 10/pkg $2.00
KN-ECT6GRN 10/pkg $2.00
KN-ECT6GRN 10/pkg $2.00
Orange KN-ECT6ORG KN-ECT6ORG KN-ECT6ORG
Red KN-ECT6RED KN-ECT6RED KN-ECT6RED
Yellow KN-ECT6YEL KN-ECT6YEL KN-ECT6YEL
White KN-ECT6WHT KN-ECT6WHT KN-ECT6WHT
Gray KN-ST1GRY 25/pkg $7.50 KN-ST1GRY 25/pkg $7.50 KN-ST1GRY 25/pkg $7.50
Blue KN-ST1BLU KN-ST1BLU KN-ST1BLU
Brown KN-ST1BRN KN-ST1BRN KN-ST1BRN
Black KN-ST1BLK KN-ST1BLK KN-ST1BLK
Separators Green KN-ST1GRN KN-ST1GRN KN-ST1GRN
(International colors) 10/pkg $3.00 10/pkg $3.00 10/pkg $3.00
Orange KN-ST1ORG KN-ST1ORG KN-ST1ORG
Red KN-ST1RED KN-ST1RED KN-ST1RED
Yellow KN-ST1YEL KN-ST1YEL KN-ST1YEL
White KN-ST1WHT KN-ST1WHT KN-ST1WHT
2-pole KN-2J12 25/pkg $7.50 KN-2J10 25/pkg $10.50 KN-2J8 25/pkg $11.00
3-pole KN-3J12 20/pkg $9.50 KN-3J10 20/pkg $12.50 KN-3J8 20/pkg $13.50
Jumpers
4-pole KN-4J12 15/pkg $11.00 KN-4J10 15/pkg $12.50 KN-4J8 15/pkg $13.00
10-pole KN-10J12 5/pkg $7.50 KN-10J10 5/pkg $9.50 KN-10J8 5/pkg $10.50
Comb-type jumper / 2-pole KN-2JCC12 25/pkg $10.00 KN-2JCC10 25/pkg $20.00 KN-2JCC8 25/pkg $21.00
Top Cover / Blank KN-TC-1 25/pkg $6.00 KN-TC-1 25/pkg $6.00 KN-TC-1 25/pkg $6.00
Top Cover / Symbol KN-TC-1s 25/pkg $8.50 KN-TC-1s 25/pkg $8.50 KN-TC-1s 25/pkg $8.50
Marking Tags KN-L5 Series KN-L5 Series KN-L5 / KN-L6P5 Series
To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number’s web page.
Technical Specifications
Model KN-T6 KN-T4 KN-T2
Width 10mm [0.39 in] 12mm [0.47 in] 16mm [0.63 in]
Stripping Length 12mm [0.47 in] 16mm [0.63 in] 18mm [0.71 in]
Tightening Torque 1.2 N·m [10.6 lb·in] 1.2 N·m [10.6 lb·in] 2.5 N·m [22.1 lb·in]
Density 100/m [33 pcs/ft] 83/m [25 pcs/ft] 62/m [19 pcs/ft]
UL/CSA Approval *300V 65A 16-6 AWG 600V 80A 12-4 AWG 600V 115A 10-2 AWG
VDE Approval 630V 57A 10mm² 750V 76A 16mm² 750V 125A 35mm²
CE Conformity 630V 57A 10mm² 750V 76A 16mm² 750V 125A 35mm²
SCCR Rating 100kA 100kA 100kA
Operating Temperature Ambient air temperature: -67°F to 185°F [-55°C to 85°C], Relative humidity: 50% max at 104°F [40°C] and 90% max at 68°F [20°C]
Material Current Bar: Copper Alloy / Housing: Polyamide 66 / Screws: Zinc Plated Steel
DIN Rail Width 35mm
Accessories
KN-ECT6GRY 100/pkg $16.00 KN-ECT4GRY 25/pkg $7.50
Gray
KN-ECT6GRY-25 25/pkg $4.00 — — —
Blue KN-ECT6BLU KN-ECT4-BLU 10/pkg $3.50
Brown KN-ECT6BRN — — —
End Covers Black KN-ECT6BLK — — — Note: KN-T2 is totally enclosed,
(International colors) Green KN-ECT6GRN 10/pkg $2.00
— — — no end cover required
Orange KN-ECTORG — — —
Red KN-ECT6RED — — —
Yellow KN-ECT6YEL — — —
White KN-ECT6WHT — — —
Gray KN-ST1GRY 25/pkg $7.50 KN-ST2GRY 25/pkg $10.00 KN-ST3GRY 10/pkg $5.00
Blue KN-ST1BLU KN-ST3BLU 10/pkg $10.00 KN-ST3BLU 10/pkg $5.00
Brown KN-ST1BRN — — — — — —
Black KN-ST1BLK — — — — — —
Separators Green KN-ST1GRN — — — — — —
(International colors) 10/pkg $3.00
Orange KN-ST1ORG — — — — — —
Red KN-ST1RED — — — — — —
Yellow KN-ST1YEL — — — — — —
White KN-ST1WHT — — — — — —
2-pole KN-2J6 25/pkg $14.00 KN-2J4 25/pkg $22.50 KN-2J2 25/pkg $23.00
3-pole KN-3J6 20/pkg $15.00 KN-3J4 20/pkg $24.00 KN-3J2 20/pkg $25.00
Jumpers
4-pole KN-4J6 15/pkg $15.00 KN-4J4 15/pkg $24.00 KN-4J2 15/pkg $25.00
10-pole KN-10J6 5/pkg $11.50 KN-10J4 5/pkg $19.00 KN-10J2 5/pkg $19.00
Comb-type jumper / 2-pole KN-2JCC6 25/pkg $23.00 — — — — — —
Top Cover / Blank KN-TC-1 25/pkg $6.00 KN-TC-2 25/pkg $15.50 KN-TC-2 25/pkg $15.50
Top Cover / Symbol KN-TC-1S 25/pkg $8.50 KN-TC-2s 25/pkg $15.50 KN-TC-2s 25/pkg $15.50
Marking Tags KN-L5/ KN-L6P5 Series KN-L5/ KN-L6P5 Series KN-L5/ KN-L6P5 Series
To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number’s web page.
Dimensions: mm [in]
Ordering Information
Colors Part Number Qty Price Part Number Qty Price Part Number Qty Price
KN-T1/0GRY 25 $65.00 KN-T2/0GRY 10 $41.00 KN-T12SP4 100 $119.00
Gray
KN-T1/0GRY-10 10 $25.00 — — — KN-T12SP4-25 25 $39.00
KN-T1/0BLU 25 $65.00 KN-T2/0BLU 10 $59.00 — — —
Blue
KN-T1/0BLU-10 10 $25.00 — — — — — —
Technical Specifications
Model KN-T1/0 KN-T2/0 KN-T12SP4
Width 20mm [0.79 in] 22mm [0.87 in] 5mm [0.20 in]
Stripping Length 20mm [0.79 in] 20mm [0.79 in] 10mm [0.39 in]
Tightening Torque 6.0 N·m [53.1 lb·in] 6.0 N·m [53.1 lb·in] 0.5 N·m [4.4 lb·in]
Density 50/m [15 pcs/ft] 45/m [13 pcs/ft] 200/m [60 pcs/ft]
UL/CSA Approval 600V 150A 6-1/0 AWG 600V 175A 6-2/0 AWG 600V 20A 26-12 AWG
CE Conformity 1000V 150A 50mm² 750V 192A 70mm² 750V 24A 2.5 mm²
SCCR Rating 100kA 100kA 10kA per Table SB4.1, 2009, UL 508A.
Operating Temperature Ambient air temperature: -67°F to 185°F [-55°C to 85°C], Relative humidity: 50% max at 104°F [40°C] and 90% max at 68°F [20°C]
Material Current Bar: Copper Alloy / Housing: Polyamide 66 / Screws: Zinc Plated Steel
DIN Rail Width 35mm
Accessories
End Covers Gray — — — — — — KN-EC12SP4 25/pkg $7.00
2-pole KN-2J1/0 5/pkg $7.00 — — — KN-2JM12 25/pkg $6.50
3-pole KN-3J1/0 5/pkg $11.50 — — — KN-3JM12 20/pkg $7.50
Jumpers
4-pole KN-4J1/0 5/pkg $15.00 — — — KN-4JM12 15/pkg $7.50
10-pole — — — — — — KN-10JM12 5/pkg $8.50
KN-L5 Series
Marking Tags No tags available
KN-L6P5 Series KN-L5 Series
To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number’s web page.
Technical Specifications
Model KN-D12 KN-D10
Width 5mm [0.20 in] 6mm [0.24 in]
Stripping Length 9mm [0.35 in] 9mm [0.35 in]
Tightening Torque 0.4 N·m [3.5 lb·in] 0.5 N·m [4.4 lb·in]
Density 200/m [60 pcs/ft] 166/m [50 pcs/ft]
UL/CSA Approval 300V 20A 26-12 AWG 300V 30A 26-10 AWG
CE Conformity 500V 24A 2.5 mm² 500V 32A 4mm²
SCCR Rating 100kA 100kA
Ambient air temperature: -67°F to 185°F [-55°C to 85°C]
Operating Temperature Relative humidity: 50% max at 104°F [40°C] and 90% max at 68°F [20°C]
Material Current Bar: Copper Alloy / Housing: Polyamide 66 / Screws: Zinc Plated Steel
DIN Rail Width 35mm
Accessories
Gray KN-ECDGRY 25/pkg $8.00 KN-ECDGRY 25/pkg $8.00
Blue KN-ECDBLU 10/pkg $4.00 KN-ECDBLU 10/pkg $4.00
Black KN-ECDBLK 10/pkg $4.00 KN-ECDBLK 10/pkg $4.00
End Covers
(International Green KN-ECDGRN 10/pkg $4.00 KN-ECDGRN 10/pkg $4.00
colors)
Orange KN-ECDORG 10/pkg $4.00 KN-ECDORG 10/pkg $4.00
Red KN-ECDRED 10/pkg $4.00 KN-ECDRED 10/pkg $4.00
Yellow KN-ECDYEL 10/pkg $4.00 KN-ECDYEL 10/pkg $4.00
2-pole KN-2J12 25/pkg $7.50 KN-2J10 25/pkg $10.50
3-pole KN-3J12 20/pkg $9.50 KN-3J10 20/pkg $12.50
Jumpers
4-pole KN-4J12 15/pkg $11.00 KN-4J10 15/pkg $12.50
10-pole KN-10J12 5/pkg $7.50 KN-10J10 5/pkg $9.50
Marking Tags KN-L5 Series
To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part
number’s web page.
Ordering Information
Color Part Number Qty Price Part Number Qty Price
Gray KN-D12X 20 $38.00 KN-D10X 20 $42.00
Technical Specifications
Model KN-D12X KN-D10X
Width 5mm [0.20 in] 6mm [0.24 in]
Stripping Length 9mm [0.35 in] 9mm [0.35 in]
Tightening Torque 0.4 N·m [3.5 lb·in] 0.5 N·m [4.4 lb·in]
Density 200/m [60 pcs/ft] 166/m [50 pcs/ft]
UL/CSA Approval 300V 20A 26-12 AWG 300V 30A 26-10 AWG
CE Conformity 500V 24A 2.5 mm² 500V 32A 4mm²
SCCR Rating 10kA per Table SB4.1, 2009, UL 508A.
Ambient air temperature: -67°F to 185°F [-55°C to 85°C]
Operating Temperature Relative humidity: 50% max at 104°F [40°C] and 90% max at 68°F [20°C]
Material Current Bar: Copper Alloy / Housing: Polyamide 66 / Screws: Zinc Plated Steel
DIN Rail Width 35mm
Accessories
End Covers Gray KN-ECDGRY 25/pkg $8.00 KN-ECDGRY 25/pkg $8.00
2-pole KN-2J12 25/pkg $7.50 KN-2J10 25/pkg $10.50
3-pole KN-3J12 20/pkg $9.50 KN-3J10 20/pkg $12.50
Jumpers*
4-pole KN-4J12 15/pkg $11.00 KN-4J10 15/pkg $12.50
10-pole KN-10J12 5/pkg $7.50 KN-10J10 5/pkg $9.50
Marking Tags KN-L5 Series
* KN-D12X and KN-D10X terminal blocks can only be jumped on the lower decks.
To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number’s
web page.
Dimensions: mm [in]
Ordering Information
Color Part Number Qty Price Part Number Qty Price Part Number Qty Price
Gray KN-D12DR1 20 $37.00 KN-D10DR1 20 $40.00 KN-DG12 20 $61.00
Technical Specifications
Model KN-D12DR1 KN-D10DR1 KN-DG12
Width 5mm [0.20 in] 6mm [0.24 in] 6mm [0.24 in]
Stripping Length 9mm [0.35 in] 9mm [0.35 in] 9mm [0.35 in]
Tightening Torque 0.4 N·m [3.5 lb·in] 0.5 N·m [4.4 lb·in] 0.4 N·m [3.5 lb·in]
Density 200/m [60 pcs/ft] 166/m [50 pcs/ft] 166/m [50 pcs/ft]
UL/CSA Approval 300V 20A 26-12 AWG 300V 30A 26-10 AWG 300V 24A 24-12 AWG
CE Conformity 500V 24A 2.5 mm² 500V 32A 4mm² 440V 24A 2.5 mm²
SCCR Rating 10kA per Table SB4.1, 2009, UL 508A. Maximum short circuit current rating for unmarked components.
Operating Temperature Ambient air temperature: -67°F to 185°F [-55°C to 85°C], Relative humidity: 50% max at 104°F [40°C] and 90% max at 68°F [20°C]
Material Current Bar: Copper Alloy / Housing: Polyamide 66 / Screws: Zinc Plated Steel
DIN Rail Width 35mm
Accessories
End Cover Gray KN-ECDGRY 25/pkg $8.00 KN-ECDGRY 25/pkg $8.00 KN-ECDG12 10/pkg $3.00
2-pole KN-2J12 25/pkg $7.50 KN-2J10 25/pkg $10.50 KN-2JTL12 25/pkg $11.50
3-pole KN-3J12 20/pkg $9.50 KN-3J10 20/pkg $12.50 KN-3JTL12 20/pkg $14.50
Jumpers
4-pole KN-4J12 15/pkg $11.00 KN-4J10 15/pkg $12.50 KN-4JTL12 15/pkg $13.00
10-pole KN-10J12 5/pkg $7.50 KN-10J10 5/pkg $9.50 KN-10JTL12 5/pkg $11.50
Marking Tags KN-L5 Series KN-L5 Series KN-L5 Series
To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number’s web page.
Ordering Information
Color Part Number Qty Price Part Number Qty Price
KN-D12LED-24DC 20 $48.00 KN-D10LED-24DC 20/pkg $54.00
Gray
KN-D12LED-110DC 20 $48.00 KN-D10LED-110DC 20/pkg $54.00
Technical Specifications
Model KN-D12LED-xxDC KN-D10LED-xxDC
Width 5mm [0.20 in] 6mm [0.24 in]
Stripping Length 9mm [0.35 in] 9mm [0.35 in]
Tightening Torque 0.4 N·m [3.5 lb·in] 0.5 N·m [4.4 lb·in]
Density 200/m [60 pcs/ft] 166/m [50 pcs/ft]
UL/CSA Approval 300V 20A 26-12 AWG 300V 30A 26-10 AWG
CE Conformity 24VDC/110VDC 24A 2.5 mm² 24VDC/110VDC 32A 4mm²
LED Voltage 2 Volts 2 Volts
10k (KN-D12LED-24DC), 2mA, 9-36 VDC 10k (KN-D10LED-24DC), 2mA, 9-36 VDC
Resistor Value 56k (KN-D12LED-110DC), 2mA, 60-150 VDC 56k (KN-D10LED-110DC), 2mA, 60-150 VDC
SCCR Rating 10kA per Table SB4.1, 2009, UL 508A. Maximum short circuit current rating for unmarked components.
Ambient air temperature: -67°F to 185°F [-55°C to 85°C]
Operating Temperature Relative humidity: 50% max at 104°F [40°C] and 90% max at 68°F [20°C]
Material Current Bar: Copper Alloy / Housing: Polyamide 66 / Screws: Zinc Plated Steel
DIN Rail Width 35mm
Accessories
End Covers Gray KN-ECDGRY 25/pkg $8.00 KN-ECDGRY 25/pkg $8.00
2-pole KN-2J12 25/pkg $7.50 KN-2J10 25/pkg $10.50
3-pole KN-3J12 20/pkg $9.50 KN-3J10 20/pkg $12.50
*Jumpers
4-pole KN-4J12 15/pkg $11.00 KN-4J10 15/pkg $12.50
10-pole KN-10J12 5/pkg $7.50 KN-10J10 5/pkg $9.50
Marking Tags KN-L5 Series KN-L5 Series
*Only lower decks can be jumpered
To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number’s web page.
Ordering Information
Part Number Qty Price Part Number Qty Price
KN-D12LED-24AC 20/pkg $48.00 KN-D10LED-24AC 20/pkg $54.00
Gray
KN-D12LED-110AC 20/pkg $48.00 KN-D10LED-110AC 20/pkg $54.00
Technical Specifications
Model KN-D12LED-xxAC KN-D10LED-xxAC
Width 5mm [0.20 in] 6mm [0.24 in]
Stripping Length 9mm [0.35 in] 9mm [0.35 in]
Tightening Torque 0.4 N·m [3.5 lb·in] 0.5 N·m [4.4 lb·in]
Density 200/m [60 pcs/ft] 166/m [50 pcs/ft]
UL/CSA Approval 300V 20A 26-12 AWG 300V 30A 26-10 AWG
CE Conformity 24VAC/110VAC 24A 2.5 mm² 24VAC/110VAC 32A 4mm²
LED Voltage 2 Volts 2 Volts
4.7k (KN-D12LED-24AC), 2.5 mA, 9-36 VAC 4.7k (KN-D10LED-24AC), 2.5 mA, 9-36 VAC
Resistor Value 33k (KN-D12LED-110AC), 2mA, 60-150 VAC 33k (KN-D10LED-110AC), 2mA, 60-150 VAC
SCCR Rating 10kA per Table SB4.1, 2009, UL 508A. Maximum short circuit current rating for unmarked components.
Ambient air temperature: -67°F to 185°F [-55°C to 85°C]
Operating Temperature Relative humidity: 50% max at 104°F [40°C] and 90% max at 68°F [20°C]
Material Current Bar: Copper Alloy / Housing: Polyamide 66 / Screws: Zinc Plated Steel
DIN Rail Width 35mm
Accessories
End Covers Gray KN-ECDGRY 25/pkg $8.00 KN-ECDGRY 25/pkg $8.00
2-pole KN-2J12 25/pkg $7.50 KN-2J10 25/pkg $10.50
3-pole KN-3J12 20/pkg $9.50 KN-3J10 20/pkg $12.50
Jumpers
4-pole KN-4J12 15/pkg $11.00 KN-4J10 15/pkg $12.50
10-pole KN-10J12 5/pkg $7.50 KN-10J10 5/pkg $9.50
Marking Tags KN-L5 Series KN-L5 Series
*Only lower decks can be jumpered
To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number’s web page.
• KN-TL14S designed to
make sensor connec-
tions more practical Dimensions: mm [in]
Ordering Information
Color Part Number Qty Price Part Number Qty Price Part Number Qty Price
Gray KN-TL14 20 $25.00 KN-TG12 20 $66.00 KN-TL14S 20 $23.00
Technical Specifications
Model KN-TL14 KN-TG12 KN-TL14S
Width 6mm [0.24 in] 6mm [0.24 in] 6mm [0.24 in]
Stripping Length 9mm [0.35 in] 9mm [0.35 in] 9mm [0.35 in]
Tightening Torque 0.4 N·m [3.5 lb·in] 0.4 N·m [3.5 lb·in] 0.5 N·m [4.4 lb·in]
Density 166/m [50 pcs/ft] 166/m [50 pcs/ft] 166/m [50 pcs/ft]
UL/CSA Approval 300V 24A 24-12 AWG 300V 24A 24-12 AWG 300V 24A 24-12 AWG
CE Conformity 440V 24A 2.5 mm² 440V 24A 2.5 mm² 550V 24A 2.5 mm²
SCCR Rating 100kA 100kA 10kA per Table SB4.1, 2009, UL 508A.
Ambient air temperature: -67°F to 185°F [-55°C to 85°C]
Operating Temperature Relative humidity: 50% max at 104°F [40°C] and 90% max at 68°F [20°C]
Material Current Bar: Copper Alloy / Housing: Polyamide 66 / Screws: Zinc Plated Steel
DIN Rail Width 35mm
Accessories
End Cover Gray kn-ectl 10/pkg $2.50 kn-ectg12 10/pkg $3.00 kn-ectls 10/pkg $3.00
2-pole kn-2jtl12 25/pkg $11.50 kn-2jtl12 25/pkg $11.50 kn-2jtl12 25/pkg $11.50
3-pole kn-3jtl12 20/pkg $14.50 kn-3jtl12 20/pkg $14.50 kn-3jtl12 20/pkg $14.50
Jumpers
4-pole kn-4jtl12 15/pkg $13.00 kn-4jtl12 15/pkg $13.00 kn-4jtl12 15/pkg $13.00
10-pole kn-10jtl12 5/pkg $11.50 kn-10jtl12 5/pkg $11.50 kn-10jtl12 5/pkg $11.50
Marking Tags KN-L5 Series KN-L5 Series KN-L5 Series
To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number’s web page.
Ordering Information
Color Part Number Qty Price Part Number Qty Price
Gray KN-TL14SLN 20 $42.00 KN-TL14SLP 20 $42.00
Technical Specifications
Model KN-TL14SLN KN-TL14SLP
Width 6mm [0.24 in] 6mm [0.24 in]
Stripping Length 9mm [0.35 in] 9mm [0.35 in]
Tightening Torque 0.5 N·m [4.4 lb·in] 0.5 N·m [4.4 lb·in]
Density 166/m [50 pcs/ft] 166/m [50 pcs/ft]
UL/CSA Approval 300V 24A 24-12 AWG 300V 24A 24-12 AWG
CE Conformity — 24A 2.5 mm² — 24A 2.5 mm²
LED Voltage 2 Volts 2 Volts
Resistor Value 10k 10k
SCCR Rating 10kA per Table SB4.1, 2009, UL 508A. Maximum short circuit current rating for unmarked components.
Ambient air temperature: -67°F to 185°F [-55°C to 85°C]
Operating Temperature Relative humidity: 50% max at 104°F [40°C] and 90% max at 68°F [20°C]
Material Current Bar: Copper Alloy / Housing: Polyamide 66 / Screws: Zinc Plated Steel
DIN Rail Width 35mm
Accessories
End Covers Gray KN-ECTLS 10/pkg $3.00 KN-ECTLS 10/pkg $3.00
2-pole KN-2JTL12 25/pkg $11.50 KN-2JTL12 25/pkg $11.50
3-pole KN-3JTL12 20/pkg $14.50 KN-3JTL12 20/pkg $14.50
Jumpers
4-pole KN-4JTL12 15/pkg $13.00 KN-4JTL12 15/pkg $13.00
10-pole KN-10JTL12 5/pkg $11.50 KN-10JTL12 5/pkg $11.50
Marking Tags KN-L5 Series KN-L5 Series
To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number’s web page.
Miniature Feed-Through
Terminal Blocks
Dimensions: mm [in]
• Screw connection KN-M12 KN-MG12
terminal
• PE snap-on connection
DIN rail
• UL E179129
(For copper wire only.
One conductor in
terminal only.)
• CE (EN 60947-7-1/
EN 60947-7-2)
Ordering Information
Color Part Number Qty Price Part Number Qty Price
KN-M12GRY 100 $36.00 — — —
Gray
KN-M12GRY-25 25 $9.00 — — —
KN-M12BLU 100 $36.00 — — —
Blue
KN-M12BLU-25 25 $9.00 — — —
Yellow/ — — — KN-MG12 50 $90.00
Green — — — KN-MG12-10 10 $19.00
Technical Specifications
Model KN-M12 KN-MG12
Width 5mm [0.20 in] 5mm [0.20 in]
Stripping Length 10mm [0.39 in] 10mm [0.39 in]
Tightening Torque 0.4 N·m [3.5 lb·in] 0.4 N·m [3.5 lb·in]
Density 200/m [60 pcs/ft] 200/m [60 pcs/ft]
UL/CSA Approval 300V 20A 26-12 AWG — — 26-12 AWG
CE Conformity 400V 24A 2.5 mm² — — 2.5 mm²
SCCR Rating 100kA 10kA per Table SB4.1, 2009, UL 508A.
Ambient air temperature: -67°F to 185°F [-55°C to 85°C]
Operating Temperature Relative humidity: 50% max at 104°F [40°C] and 90% max at 68°F [20°C]
Material Current Bar: Copper Alloy / Housing: Polyamide 66 / Screws: Zinc Plated Steel
DIN Rail Width 15mm
Accessories
KN-ECMGRY-10 10/pkg $4.00 — — —
Gray
KN-ECMGRY 100/pkg $34.50 — — —
End Covers
(International colors) Blue KN-ECMBLU 10/pkg $4.00 — — —
Green/ — — — KN-ECMGRN 10/pkg $4.00
Yellow
2-pole KN-2JM12 25/pkg $6.50 — — —
3-pole KN-3JM12 20/pkg $7.50 — — —
Jumpers
4-pole KN-4JM12 15/pkg $7.50 — — —
10-pole KN-10JM12 5/pkg $8.50 — — —
Marking Tags KN-L5 Series KN-L5 Series
To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part
number’s web page.
Miniature Feed-Through
Terminal Blocks
Dimensions: mm [in]
• Screw connection KN-M10 KN-MG10
terminal
• PE snap-on connection
DIN rail
• UL E179129
(For copper wire only.
One conductor in
terminal only.)
• CE (EN 60947-7-1)
Ordering Information
Color Part Number Qty Price Part Number Qty Price
KN-M10GRY 100 $45.00 — — —
Gray
KN-M10GRY-25 25 $10.00 — — —
W
KN-M10BLU 100 $45.00 — — —
Blue
KN-M10BLU-25 25 $10.00 — — —
Technical Specifications
Model KN-M10 KN-MG10
Width 6mm [0.24 in] 6mm [0.24 in]
Stripping Length 10mm [0.39 in] 10mm [0.39 in]
Tightening Torque 0.5 N·m [4.4 lb·in] 0.5 N·m [4.4 lb·in]
Density 166/m [50 pcs/ft] 166/m [50 pcs/ft]
UL/CSA Approval 300V 30A 26-10 AWG — — 26-10 AWG
CE Conformity 400V 32A 4mm² — — 4mm²
SCCR Rating 100kA 10kA per Table SB4.1, 2009, UL 508A.
Ambient air temperature: -67°F to 185°F [-55°C to 85°C]
Operating Temperature Relative humidity: 50% max at 104°F [40°C] and 90% max at 68°F [20°C]
Material Current Bar: Copper Alloy / Housing: Polyamide 66 / Screws: Zinc Plated Steel
DIN Rail Width 15mm
Accessories
KN-ECMGRY-10 10/pkg $4.00 — — —
Gray
KN-ECMGRY 100/pkg $34.50 — — —
End Covers Blue KN-ECMBLU 10/pkg $4.00 — — —
Green/ — — — KN-ECMGRN 10/pkg $4.00
Yellow
2-pole KN-2JM10 25/pkg $7.00 — — —
3-pole KN-3JM10 20/pkg $8.50 — — —
Jumpers
4-pole KN-4JM10 15/pkg $10.00 — — —
10-pole KN-10JM10 5/pkg $9.50 — — —
Marking Tags KN-L5 Series KN-L5 Series
To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part
number’s web page.
Dimensions: mm [in]
• Screw connection
terminal KN-G10 KN-G8 KN-G4
• PE screw connection
DIN Rail
• UL E179129
(For copper wire only.
One conductor in
terminal only.)
• CE (EN 60947-7-1/
EN 60947-7-2)
• VDE (IEC 60947-7-1)
See our website: www.AutomationDirect.com for complete engineering drawings
Ordering Information
Color Part Number Qty Price Part Number Qty Price Part Number Qty Price
Yellow/ KN-G10 50 $87.00 KN-G8 25 $55.00 KN-G4 50 $215.00
Green KN-G10-10 10 $19.00 KN-G8-10 10 $23.00 KN-G4-10 10 $42.00
Technical Specifications
Model KN-G10 KN-G8 KN-G4
Width 6mm [0.24 in] 10mm [0.39 in] 12mm [0.47 in]
Stripping Length 10mm [0.39 in] 12mm [0.47 in] 12mm [0.47 in]
Tightening Torque 0.5 N·m [4.4 lb·in] 1.2 N·m [10.6 lb·in] 1.2 N·m [10.6 lb·in]
Density 166/m [50 pcs/ft] 100/m [30 pcs/ft] 83/m [25 pcs/ft]
UL/CSA Approval — — 26-10 AWG — — 16-8 AWG — — 12-4 AWG
VDE Approval — — 4mm² — — 10mm² — — 16mm²
CE Conformity — — 4mm² — — 10mm² — — 16mm²
Operating Temperature Ambient air temperature: -67°F to 185°F [-55°C to 85°C], Relative humidity: 50% max at 104°F [40°C] and 90% max at 68°F [20°C]
SCCR Rating 10kA per Table SB4.1, 2009, UL 508A. Maximum short circuit current rating for unmarked components.
Material Current Bar: Copper Alloy / Housing: Polyamide 66 / Screws: Zinc Plated Steel
DIN Rail Width 35mm
Accessories
KN-L5 Series KN-L5 Series
Marking Tags KN-L5 Series
KN-L6 Series KN-L6 Series
To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number’s web page.
Dimensions: mm [in]
Ordering Information
Color Part Number Qty Price Part Number Qty Price
Yellow/ KN-G2 40 $187.00 KN-G1/0 10 $54.00
Green KN-G2-10 10 $45.00 KN-G1/0-5 5 $29.00
Technical Specifications
Model KN-G2 KN-G1/0
Width 16mm [0.63 in] 20mm [0.79 in]
Stripping Length 18mm [0.71 in] 20mm [0.79 in]
Tightening Torque 2.5 N·m [22.1 lb·in] 6 N·m [22.1 lb·in]
Density 62/m [19 pcs/ft] 50/m [15 pcs/ft]
UL/CSA Approval — — 12-2 AWG — — 6-1/0 AWG
VDE Approval — — 35mm² — — 50mm²
CE Conformity — — 35mm² — — 50mm²
Ambient air temperature: -67°F to 185°F [-55°C to 85°C]
Operating Temperature Relative humidity: 50% max at 104°F [40°C] and 90% max at 68°F [20°C]
10kA per Table SB4.1, 2009, UL 508A.
SCCR Rating Maximum short circuit current rating for unmarked components.
Material Current Bar: Copper Alloy / Housing: Polyamide 66 / Screws: Zinc Plated Steel
DIN Rail Width 35mm 35mm
Accessories
KN-L5 Series
Marking Tags No tags available
KN-L6P5 Series
To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part
number’s web page.
• Screw connection
terminal
• PE snap-on
Dimensions: mm [in]
connection
• UL E179129 KN-G12SP KN-G12SP4 KN-G10SP
(For copper
wire only. One
conductor in
terminal only.)
• CE (EN 60947-7-1/
EN 60947-7-2)
• VDE (IEC 60947-7-2)
Ordering Information
Color Part Number Qty Price Part Number Qty Price Part Number Qty Price
Yellow/ KN-G12SP 50 $69.00 KN-G12SP4 25/pkg $55.00 KN-G10SP 50/pkg $77.00
Green KN-G12SP-10 10 $15.00 KN-G12SP4-10 10/pkg $24.00 KN-G10SP-10 10/pkg $17.00
Technical Specifications
Model KN-G12SP KN-G12SP4 KN-G10SP
Width 5.75 mm [0.23 in] 5mm [0.20 in] 6mm [0.24 in]
Stripping Length 10mm [0.39 in] 10mm [0.39 in] 10mm [0.39 in]
Tightening Torque 0.4 N·m [3.5 lb·in] 0.5 N·m [4.4 lb·in] 0.5 N·m [4.4 lb·in]
Density 53 pcs/ft [173/m] 200/m [60 pcs/ft] 161/m [49 pcs/ft]
UL/CSA Approval — — 26-12 AWG — — 26-12 AWG — — 26-10 AWG
VDE Approval — — 2.5 mm² — — 2.5 mm² — — 4mm²
CE Conformity — — 2.5 mm² — — 2.5 mm² — — 4mm²
Operating Temperature Ambient air temperature: -67°F to 185°F [-55°C to 85°C], Relative humidity: 50% max at 104°F [40°C] and 90% max at 68°F [20°C]
SCCR Rating 10kA per Table SB4.1, 2009, UL 508A. Maximum short circuit current rating for unmarked components.
Material Current Bar: Copper Alloy / Housing: Polyamide 66 / Screws: Zinc Plated Steel
DIN Rail Width 35mm
Accessories
Yellow/
End Covers — — — KN-ECG12SP4 10/pkg $3.00 — — —
Green
Marking Tags KN-L5 Series KN-L5 Series KN-L5 Series
To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number’s web page.
Dimensions: mm [in]
• Screw connection KN-F10 KN-F10LxxDC KN-F10LxxAC
terminal
• UL E179129
(For copper wire only.
One conductor in
terminal only.)
• CE (EN 60947-7-3)
• Fuse series: GMA, GMC,
S500, S506
Ordering Information
Color Part Number Qty Price Part Number Qty Price Part Number Qty Price
KN-F10 50 $83.00 KN-F10L24DC 25 $50.00 KN-F10L24AC 25 $50.00
KN-F10-10 10 $19.00 KN-F10L24DC-10 10 $22.00 KN-F10L24AC-10 10 $22.00
— — — KN-F10L110DC 25 $50.00 KN-F10L110AC 25 $50.00
Gray
— — — KN-F10L110DC-10 10 $22.00 KN-F10L110AC-10 10 $22.00
— — — KN-F10L220DC 25 $50.00 KN-F10L220AC 25 $50.00
— — — KN-F10L220DC-10 10 $22.00 KN-F10L220AC-10 10 $22.00
Technical Specifications
Model KN-F10 KN-F10LxxDC KN-F10LxxAC
Width 8mm [0.31 in] 8mm [0.31 in] 8mm [0.31 in]
Stripping Length 12mm [0.47 in] 12mm [0.47 in] 12mm [0.47 in]
Tightening Torque 0.8 N·m [7.1 lb·in] 0.8 N·m [7.1 lb·in] 0.8 N·m [7.1 lb·in]
Density 125/m [38 pcs/ft] 125/m [38 pcs/ft] 125/m [38 pcs/ft]
UL/CSA Approval 300V 6.3 A 26-8 AWG 300V 6.3A 26-8 AWG 300V 6.3 A 26-8 AWG
CE Conformity 500V 6.3 A 6mm² 24/110VDC 6.3A 6mm² 24/110VAC 6.3 A 6mm²
LED Voltage — 2 Volts —
10k (KN-F10L24DC), 2mA, 9-36VDC 4.7k (KN-F10L24AC), 2.5 mA, 9-36VAC
Resistor Value — 56k (KN-F10L110DC), 2mA, 60-150VDC 33k (KN-F10L110AC), 2mA, 60-150VAC
220k (KN-F10L220DC), 1mA, 100-250VDC 56k (KN-F10L220AC), 2mA, 100-250VAC
Operating Temperature Ambient air temperature: -67°F to 185°F [-55°C to 85°C], Relative humidity: 50% max at 104°F [40°C] and 90% max at 68°F [20°C]
SCCR Rating 10kA per Table SB4.1, 2009, UL 508A. Maximum short circuit current rating for unmarked components.
Material Current Bar: Copper Alloy / Housing: Polyamide 66 / Screws: Zinc Plated Steel
DIN Rail Width 35mm
Accessories
End Covers / Gray KN-ECF10 25/pkg $9.00 KN-ECF10 25/pkg $9.00 KN-ECF10 25/pkg $9.00
KN-L5 Series KN-L5 Series KN-L5 Series
Marking Tags KN-L6P5 Series KN-L6P5 Series KN-L6P5 Series
To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number’s web page.
Dimensions: mm [in]
KN-F10-DCH KN-KBD10
• Screw connection
terminal
• UL E179129
(For copper wire only.
One conductor in
terminal only.)
• CE (EN 60947-7-1)
Ordering Information
Color Part Number Qty Price Part Number Qty Price
KN-F10-DCH 25 $37.00 KN-KBD10 50 $61.00
Gray
KN-F10-DCH-10 10 $20.00 KN-KBD10-10 10 $15.00
Technical Specifications
Model KN-F10-DCH KN-KBD10
Width 8mm [0.31 in] 6.2 mm [0.24 in]
Stripping Length 12mm [0.47 in] 10mm [0.39 in]
Tightening Torque 0.8 N·m [7.1 lb·in] 0.5 N·m [4.4 lb·in]
Density 125/m [38 pcs/ft] 166/m [50 pcs/ft]
UL/CSA Approval 300V 6.3 A 26-8 AWG 600V 16A 26-10 AWG
CE Conformity 500V 6.3 A 6mm² 500V 16A 4mm²
Operating Ambient air temperature: -67°F to 185°F [-55°C to 85°C]
Temperature Relative humidity: 50% max at 104°F [40°C] and 90% max at 68°F [20°C]
10kA per Table SB4.1, 2009, UL 508A.
SCCR Rating Maximum short circuit current rating for unmarked components.
Material Current Bar: Copper Alloy / Housing: Polyamide 66 / Screws: Zinc Plated Steel
DIN Rail Width 35mm
Accessories
End Covers Gray KN-ECF10 25/pkg $9.00 KN-ECKBD 10/pkg $4.00
KN-L5 Series
Marking Tags KN-L5 Series
KN-L6P5 Series
To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number’s web page.
Entrelec Konnect-It
115 486.03 KN-T12GRY
125 486.05 KN-T12BLU
115 116.07 KN-T10GRY
125 116.01 KN-T10BLU
115 118.11 KN-T8GRY
125 118.13 KN-T8BLU
115 120.17 KN-T6GRY
125 120.11 KN-T6BLU
115 129.14 KN-T4GRY
125 129.16 KN-T4BLU
115 124.07 KN-T2GRY
125 124.01 KN-T2BLU
115 216.13 KN-T2/0GRY
125 216.15 KN-T2/0BLU
115 490.13 KN-D12GRY
125 490.15 KN-D12BLU
115 271.22 KN-D10GRY
115.541.11 KN-TL14
115 542.12 KN-TL14S
115 643.27 KN-DG12
110 251.05 KN-M10GRY
120 251.07 KN-M10BLU
165 488.27 KN-G10
165 113.16 KN-G10
165 114.17 KN-G8
165 115.10 KN-G8
165 130.23 KN-G4
165 111.14 KN-G2
160 496.26 KN-MG10
115 657.25 KN-F10
115 604.21 KN-F10SP
115 986.00 KN-KBD10
Konnect-It® Accessories
Multi-Pole Jumper Bars
KN-10J12
Multi-pole jumper bars provide terminal block connection flexibility. Screw-down
connection jumpers feature all-metal construction and can be installed quickly just
by tightening the screws. Screwless comb-style jumpers are also available. See next
page for I/O jumper installation instructions.
• KN-T1/0GRY
• KN-T1/0GRY-10
• KN-T1/0BLU
• KN-T1/0BLU-10
Applicable to jumpers:
• KN-2J1/0
• KN-3J1/0
• KN-4J1/0
Remove
only internal
knockout panels
To avoid shock hazard
IMPORTANT! • Leave external knockout panels intact
• Install removable covers into original position.
Replace Removable
Covers
CLICK
To avoid
exposure to live circuit, do not
remove external knockout panels
Konnect-It® Accessories
End Brackets
End brackets prevent terminal blocks and other DIN rail mount components and devices from moving laterally on the
rail. They are constructed from polyamide 66 and available in configurations for 35mm and 15mm DIN rails.
Dimensions mm [in]
KN-EB3 KN-EB4 KN-EB5 KN-EB7
End Covers
End covers are used to cover the open side of sectional DIN rail mount terminal
blocks. They should be used at the end of an assembly of identical terminal blocks
or whenever there is a change in the physical size of the terminal block.
Material: Polyamide 66
KN-ECDGRN green
Konnect-It® Accessories
Separators
Separators are used to segment banks of terminal blocks. Allows you to maintain a
single row of terminal blocks, but have separate power source clusters.
KN-TC-1 KN-TC-1S
KN-MA-3
Konnect-It® Accessories
Marking Tags 5 x 5mm
Use with any Konnect-It series terminal blocks
Konnect-It® Accessories
Marking Tags 6.5 x 10mm
Use with any Konnect-It series terminal blocks 6.5mm or wider.
35 mm wide
• Non-anodized finish
• Galvanic zinc plating and passivation
(minimum thickness 6 microns)
• Lightweight, easy to cut and deburr
• Terminal blocks only
Pcs/ Price/ Pcs/ Price/
• Maximum mounting screw #10-32 or M5 Part Number Pkg Pkg Part Number Pkg Pkg
• Available in 1-meter lengths
DN-R35SAL1 10 $36.00
DIN Rail DN-R35SAL2-2 2 $24.25
35 mm wide raised DN-R35SAL1-2 2 $8.00
• Non-anodized finish Aluminum DIN Rails Specifications
• Galvanic zinc plating and passivation (minimum
thickness 6 microns) Aluminum, slotted, 3'3" (1 m) length, Aluminum, slotted, 3'3" (1 m) length,
• Enables users to raise terminal blocks 2¼" above Description 35 mm (1.38 in) wide, 35 mm (1.38 in) wide,
10 mm (0.39 in) high 58 mm (2.28 in) high
the back panel
• Terminal blocks only Plating Galvanic zinc plating, non-anodized finish
• Available in 1-meter lengths International
• Bushing or grommet recommended for wire ac- DIN 50960, RoHs
Standards
cess hole
Suggested
(example Heyco UB-875 not sold by ADC) Mounting #10-32 or M5
Screw Type
DN-R35SAL1
DN-R35SAL1-2
DN-R35SAL2-2
DN-ASB1 30˚angled DIN rail support bracket (M6-1.0 screws not included) 50 $49.50
DN-ASB2-10 30˚angled DIN rail support bracket (M6-1.0 screws included) 10 $12.00
DN-SSB25-10 1” (25 mm) DIN rail support bracket (M6-1.0 screws included) 10 $17.00
DN-SSB50-10 2” (50 mm) DIN rail support bracket (M6-1.0 screws included) 10 $18.25
2.75” (70 mm) DIN rail support bracket (M6-1.0 screws
DN-SSB70-10 included) 10 $23.00
DN-SSB90-10 3.5” (90 mm) DIN rail support bracket (M6-1.0 screws included) 10 $24.25
DN-CLIP-FM4 40 $45.00
DIN rail mounting clip with M4 x 0.7 mm threaded hole
(Screws not included)
DN-CLIP-FM4-5 5 $6.25
DN-CLIP-FM5 40 $49.50
DIN rail mounting clip with M5 x 0.8 mm threaded hole
(Screws not included)
DN-CLIP-FM5-5 5 $7.00
DN-CLIP-FM4 DN-CLIP-FM5
DN-SSB70-10 DN-SSB90-10 DN-CLIP-FM4-5 DN-CLIP-FM5-5
DN-ASB1 DN-ASB2-10
DN-CLIP-FM4 DN-CLIP-FM5
AutomationDirect prices are U.S. published prices from April 2014 Price List.
Prices subject to change without notice.
It could cost you a lot more in the long run. But you don’t need to overpay to get reliable,
high-performance safety devices that conform to all the latest standards. Our prices on
safety relays, switches and light curtains mean you can do even more to protect what’s important.
Marking system
• Inclined at a 45O angle
for easy reading
• Can be marked by hand
or preprinted from
Wire stops 0-1000
• Stops wires from being
inserted too far
Funneled wire entry
• Allows for fast and easy
insertion of the wire into
the clamp
• Closed on all four sides
for safety
Quality materials
1 3
High-contact pressure
DINnectors are manufactured from Polyamide 6.6 plas- Continuous, high-contact pressure is essential for a
tic with very good electrical, mechanical, and chemical reliable connection. Even the best conductors give
properties. This UL-approved material has a flammabil- poor results if the contact pressure is insufficient.
ity rating of V2 (self-extinguishing) according to UL94. Low-contact pressure causes aggravating and dan-
It has a continuous upper temperature limit of 105°C, gerous intermittent connections. DINnectors termi-
and a lower temperature limit of -20°C. The Compara- nal block screw clamp connection technology offers
tive Tracking Index is CTI>600, with an average humid- the highest contact pressure available. DINnectors 12
ity absorption of 3-4 percent. AWG terminal block produces a high contact force of
DINnectors screws and clamps are manufactured from approximately 169 ft/lbs (750 Nm).
hardened steel plated with a zinc-dichromate corrosion-
Low voltage drop
4
resistant finish. The current bars are made from a cop-
per alloy with a tin/lead plating.
Many electrical engineers consider voltage drop values
DINnectors terminal blocks boast a long-term storage across the connection points to be an excellent meas-
temperature range of -13°F to 131°F (-25°C to 55°C). ure of the quality of the terminal block. Low voltage
drop means low contact resistance, which indicates
terminal connector
Weidmuller
terminal connector
Phoenix Contact
terminal connector
Specifying a Terminal
Block System
Step 2: Determine Step 4: Calculate
the electrical the rail length
specifications Calculate the density per foot of each
Determine your requirements for the type and quantity of terminal block in
maximum wire size, current, and voltage your assembly to determine the total
for each terminal block. rail length. Remember to add 1/2 inch
for each rail end to accommodate rail
mounting screws. Also add 0.0008”
Step 3: Select the (0.2 mm) tolerance per terminal, plus the
accessories width of the end brackets, end covers,
and any separators.
Choose between deep or shallow then
Step 1: Select the type select the appropriate end cover(s) and
Choose from the many types of ter- end brackets. Then decide if you would Step 5: Place your
minal blocks as required for your sys-
tem: screw-type or screwless, feed-
like to use internal jumpers, top covers,
angled support brackets, test plugs, sep-
order!
through, multi-level, mini, ground, arators, or blank or printed marking tags. Call 1-800-633-0405 or visit our Web
fuse, disconnect or direct mount. site at www.automationdirect.com
to order.
Multi-level/Sensor Terminal Blocks Double-level terminal blocks offer twice the wiring density of feed-through blocks. Triple-level blocks
enable either high-density wiring or simplified, low-cost sensor wiring.
Ground terminal blocks are used to mechanically and electrically connect wires to the
Ground Terminal Blocks
DIN rail, thus allowing the rail to function as a ground bus bar.
Fuse blocks provide easily-replaceable fuse protection for PLC output devices or modules.
Circuit Protection Blocks
They are available for 1/4”, 5 mm Midget and Class CC size fuses.
Disconnect Terminal Blocks Convenient operation allows fast circuit Mini terminal blocks are used in ar
Mini Terminal Blocks
disconnection without rewiring. extremely limited space require
Book 3 (14.1)
eTB-39
w w w. a Terminal
u t o m a t Blocks
iondirect.com/terminal-blocks 1 - 8 0 0 - tTBL-39
Terminal Blocks 633 - 0 4 0 5
Prices as of April
For16,
latest
2014.
prices,
Check
please
Webcheck
site for
AutomationDirect.com
most current prices.
DINnector standard
terminal blocks
• Polyamide 6.6 plastic molding
• Zinc dichromate-plated, hardened steel
screws and clamps
DN-T1/0 DN-T3/0 • Nickel-plated, copper current bar
• Single or double-level blocks
DN-THERM1 DN-THERM2
tTBL-40
w w w. a u t oTerminal
m a t i o nBlocks
direct.com/terminal-blocks 1 - 8 0 0 - 633 - 0 4 0 5
For latest prices, please check AutomationDirect.com
Dimensions Blue
Brown
DN-T12B-A
DN-T12BR-A
100 $42.00 DN-T10B-A
100 $42.00 DN-T10BR-A
100 $47.50 DN-T8B
100 $47.50 –
50
–
$38.00
–
mm [inches] Black DN-T12BLK-A 100 $42.00 DN-T10BLK-A 100 $47.50 DN-T8BLK 50 $38.00
Available Green DN-T12GRN-A 100 $42.00 DN-T10GRN-A 100 $47.50 DN-T8GRN 50 $38.00
DN-T12-A Colors
Orange DN-T12ORG-A 100 $42.00 DN-T10ORG-A 100 $47.50 DN-T8ORG 50 $38.00
Red DN-T12RED-A 100 $42.00 DN-T10RED-A 100 $47.50 DN-T8RED 50 $38.00
Yellow DN-T12YEL-A 100 $42.00 DN-T10YEL-A 100 $47.50 DN-T8YEL 50 $38.00
White DN-T12W-A 100 $42.00 DN-T10W-A 100 $47.50 DN-T8W 50 $38.00
Technical Specifications
Stripping Length 10mm [0.39 in] 10mm [0.39 in] 12mm [0.47 in]
Tightening Torque 0.5 N·m [4 lb·in] 0.8 N·m [7 lb·in] 1.2 N·m [10.6 lb·in]
Density 200/m [60 pcs/ft] 166/m [50 pcs/ft] 142/m [43 pcs/ft]
UL Approval* 600V 20A 24-12 AWG 600V 30A 24-10 AWG 600V 50A 22-8 AWG
CSA Approval 600V 24A 24-12 AWG 600V 30A 24-10 AWG 600V 50A 22-8 AWG
VDE Approval 800V 24A 2.5 mm² 800V 32A 4mm² 800V 41A 6mm²
Operating Ambient air temp: -20°C to 105°C [-4°F to 221°F]
DN-T10-A Temperature Relative humidity: 50% max at 40°C [104°F]; 90% max at 20°C [68°F]
SCCR Rating 10kA per Table SB4.1, 2009, UL 508A, maximum short circuit current rating for unmarked components
CE Conformity CE (EN 60947-1 / EN 60947-7-1)
Agency File # UL E179129
Note: To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number's web page.
Accessories
DN-EC1210 100 $26.00 DN-EC1210 100 $26.00 DN-EC86 100 $28.00
End Covers
DN-EC1210MN 25 $8.00 DN-EC1210MN 25 $8.00 DN-EC86MN 25 $8.00
DN-S1210 100 $30.50 DN-S1210 100 $30.50 DN-S86 100 $36.50
Separators
DN-S1210MN 25 $9.25 DN-S1210MN 25 $9.25 DN-S86MN 25 $7.75
DN-2J2Y 100 $26.00 DN-2J4Y 100 $27.50
2-pole
DN-2J2YMN 25 $7.50 DN-2J4YMN 25 $8.00
–
Jumpers DN-3J2Y 100 $36.50 DN-3J4Y 100 $43.50
3-pole
DN-T8
DN-3J2YMN 25 $10.25 DN-3J4YMN 25 $12.00
24-pole DN-24J2Y 5 $16.00 DN-24J4Y
DN-24J8 5 $24.00 5 $17.00
Jumper Cutting DN-J2CUT 1 $46.50 DN-J4CUT 1 $46.50 –
Tool**
DN-C12 100 $36.50 DN-C10 100 $36.50 DN-C86 100 $36.50
Top Cover
DN-C12MN 25 $7.75 DN-C10MN 25 $7.75 DN-C86MN 25 $7.75
Test Plug/Red DN-TPR 10 $24.50 DN-TPR 10 $24.50
–
Test Plug/Black DN-TPB 10 $24.50 DN-TPB 10 $24.50
7.5 mm DN-R35S1 10 $28.00 DN-R35S1 10 $28.00 DN-R35S1 10 $28.00
35mm high DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00
DIN Rail 15mm DN-R35HS1 10 $49.50 DN-R35HS1 10 $49.50 DN-R35HS1 10 $49.50
high DN-R35HS1-2 2 $12.00 DN-R35HS1-2 2 $12.00 DN-R35HS1-2 2 $12.00
DN-EB35 50 $39.50 DN-EB35 50 $39.50 DN-EB35 50 $39.50
DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00
DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50
End Brackets
DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50
DN-QEB35 50 $25.50 DN-QEB35 50 $25.50 DN-QEB35 50 $25.50
DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50
Angled
Support Bracket DN-ASB1
50 $49.50 DN-ASB1 50 $49.50 DN-ASB1 50 $49.50
Marking Tags DN-LA or 500/ various DN-L or 500/ various DN-L or 500/ various
DN-LT series 100 DN-LT series 100 DN-LT series 100
*Copper Wire Only
**Jumper Cutting Tools DN-JxCUT cut the applicable multi-pole jumpers and MAINTAIN THE JUMPER INSULATION
Note: For more information on accessories, see the DINnectors Accessories section of this chapter.
• Screw connection
terminal
• 35mm DIN-rail
mountable
• LVD 2006/95/EC
Dimensions
DN-T3/0
DN-T6 DN-T4 DN-T1/0
44 mm
75 mm 49 mm
[1.73 in]
[2.95 in]
[1.93 in] 61 mm
[2.40 in]
50 mm
74 mm [1.97 in] 9 mm 56 mm
[2.91 in] 26 mm 62 mm
[0.35 in] [2.20 in] 12 mm
[1.02 in] [2.44 in] 16 mm
[0.47 in]
[0.63 in]
Note: Screw is a Hex Bolt, Size M8
DN-D10-A DN-D10X-A**
Series: EURO D 4-2/35 Series: EURO D 4-2/35
Ordering Information
Part Number Pcs/Pkg Price Part Number Pcs/Pkg Price Dimensions
Gray DN-D10-A 50 $78.00 DN-D10X-A 50 $117.00
Blue DN-D10B-A 50 $81.00
Black DN-D10BLK-A 50 $81.00
Available Green DN-D10GRN-A 50 $81.00 DN-D10-A
Colors –
Orange DN-D10ORG-A 50 $81.00 6mm [0.24 in]
Red DN-D10RED-A 50 $81.00 75 mm [2.95 in]
Yellow DN-D10YEL-A 50 $81.00
56 mm [2.20 in]
Technical Specifications
Stripping Length 10mm [0.39 in] 10mm [0.39 in]
Tightening Torque 0.6 N·m [7 lb·in] 0.6 N·m [7 lb·in]
Density 166/m [50 pcs/ft] 166/m [50 pcs/ft]
UL Approval* 600V 30A 24-10 AWG 600V 30A 24-10 AWG
CSA Approval 600V 30A 24-10 AWG 600V 30A 24-10 AWG
VDE Approval 800V 32A 4mm² 800V 32A 4mm²
Ambient air temperature: -20°C to 105°C [-4°F to 221°F]
Operating Temperature Relative humidity: 50% max at 40°C [104°F]; 90% max at 20°C [68°F]
10kA per Table SB4.1, 2009, UL 508A,
SCCR Rating Maximum short circuit current rating for unmarked components
CE Conformity CE (EN 60947-1 / EN 60947-7-1) DN-D10X-A
Agency File # UL E179129 6mm [0.24 in]
Note: To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number's web page. 75 mm [2.95 in]
Accessories
56 mm [2.20 in]
Ordering Information
Part Number Pcs/Pkg Price Part Number Pcs/Pkg Price
Color Gray DN-D10LED1-A 10 $31.50 DN-D10DR-A 50 $119.00 LED terminal blocks
Technical Specifications These terminal blocks have
Stripping Length 10mm [0.39 in] 10mm [0.39 in]
built‑in LED indicators. The
Tightening Torque 0.6 N·m [7 lb·in] 0.6 N·m [7 lb·in]
LED illuminates when voltage is
Density 166/m [50 pcs/ft] 166/m [50 pcs/ft]
present. The LED1 version
LED Voltage 12-24 V AC/DC 3.4 kΩ –
UL Approval* 600V 30A 24-10 AWG 600V 1A (Diode) 24-10 AWG is for 24V AC/DC circuits,
CSA Approval 600V 30A 24-10 AWG 600V 1A (Diode) 24-10 AWG and includes current-limiting
VDE Approval 800V 32A 4mm² 800V 1A (Diode) 4mm² elements. Note: Wire only one supply.
Ambient air temperature: -20°C to 105°C [-4°F to 221°F]
Operating Temperature Relative humidity: 50% max at 40°C [104°F]; 90% max at 20°C [68°F]
10kA per Table SB4.1, 2009, UL 508A, DN-D10LED1-A
SCCR Rating Maximum short circuit current rating for unmarked components
24VAC +24VDC
CE Conformity CE (EN 60947-1 / EN 60947-7-1)
Agency File # UL E179129
Note: To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number's web page.
Accessories
DN-DEC10 50 $18.00 DN-DEC10 50 $18.00 110VAC
End Covers +110VDC
DN-DEC10MN 10 $3.75 DN-DEC10MN 10 $3.75 Diode terminal blocks
DN-2J4Y 100 $27.50 DN-2J4Y 100 $27.50
Typically, an inductive load
2-pole
DN-2J4YMN 25 $8.00 DN-2J4YMN 25 $8.00
produces a spike (neg.-going)
Jumpers** DN-3J4Y 100 $43.50 DN-3J4Y 100 $43.50
3-pole when it is turned off. These
DN-3J4YMN 25 $12.00 DN-3J4YMN 25 $12.00
24-pole DN-24J4Y 100 $17.00 DN-24J4Y 100 $17.00 terminal blocks with built-in diodes
Jumper Cutting Tool*** DN-J4CUT 1 $46.50 DN-J4CUT 1 $46.50 help protect your PLC’s output
DN-DC10 100 $34.50 DN-DC10 100 $34.50 circuits. The circuit below shows
Top Cover the normal voltages to the load
DN-DC10MN 25 $7.75 DN-DC10MN 25 $7.75
Test Plug/Red DN-TPR 10 $24.50 DN-TPR 10 $24.50 (during ON state). (Please see
Test Plug/Black DN-TPB 10 $24.50 DN-TPB 10 $24.50 application note AN-MISC-032 at
7.5 mm DN-R35S1 10 $28.00 DN-R35S1 10 $28.00 http://support.automationdirect.
35mm high DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00 com/docs/an-misc-032.pdf)
DIN Rail 15mm DN-R35HS1 10 $49.50 DN-R35HS1 10 $49.50
high DN-R35HS1-2 2 $12.00 DN-R35HS1-2 2 $12.00
DN-EB35 50 $39.50 DN-EB35 50 $39.50 DN-D10DR-A
DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00
DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50 +V
End Brackets
DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50
DN-QEB35 50 $25.50 DN-QEB35 50 $25.50
DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50
Angled Support Bracket DN-ASB1 50 $49.50 DN-ASB1 50 $49.50 1N4007 Reverse bias diode
DN-L or DN-L or (See Diode information
Marking Tags 500/100 various 500/100 various
DN-LT series DN-LT series + V eTB-69)
located on page
*Copper wire only
**Jumpering and testing should be done on bottom level only.
***Jumper Cutting Tool DN-J4CUT cuts DN-xJ4Y Series multi-pole jumpers and MAINTAINS THE JUMPER INSULATION.
For more information on accessories, see the DINnectors Accessories section of this chapter.
14 SOR
Triple-level terminal blocks
G SEN
AW enable high-density wiring or
simplified, low-cost sensor
• Screw connection wiring.
terminal
• 35mm DIN-rail When wiring space is at a
mountable premium, use the DN‑TL14-A to
• LVD 2006/95/EC DN-TL14-A connect three separate circuits
Series: EURO W 2.5/35 DN-TL14S-A in only 5mm of linear DIN-rail
Series: EURO Z 2.5/35 space. The rest of our family
of triple-level blocks will allow
Ordering Information
you to wire one terminal block
Part Number Pcs/Pkg Price Part Number Pcs/Pkg Price
per sensor, vs. the traditional
Color Gray DN-TL14-A 25 $41.00 DN-TL14S-A 25 $35.50
method, which requires three
Technical Specifications different single-level blocks per
Stripping Length 10 mm [0.39 in] 10 mm [0.39 in]
sensor
Tightening Torque 0.5 N·m [4.5 lb·in] 0.5 N·m [4.5 lb·in]
Density 200/m [57 pcs/ft] 200/m [57 pcs/ft] The DN‑TL14S-A is the
UL Approval* 300V 10A 26-14 AWG 300V 10A 26-14 AWG standard sensor terminal block,
CSA Approval 300V 10A 26-14 AWG 300V 10A 26-14 AWG and the DN‑TL14SLP-A and
VDE Approval 300V 10A 2.5 mm² 300V 10A 2.5 mm² DN‑TL14SLN-A provide LED
Ambient air temperature: -20°C to 105°C [-4°F to 221°F] indication at the terminal block
Operating Temperature Relative humidity: 50% max at 40°C [104°F]; 90% max at 20°C [68°F] when voltage is present.
10kA per Table SB4.1, 2009, UL 508A,
SCCR Rating Maximum short circuit current rating for unmarked components
CE Conformity CE (EN 60947-1 / EN 60947-7-1)
Agency File # UL E179129 Dimensions
Note: To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number's web page.
Accessories
End Covers DN-EC14 25 $10.00 DN-EC14S 25 $9.00
DN-2JL14B-A DN-2JL14B-A DN-TL14-A
2-pole 100 $39.00 100 $39.00
Blue DN-2JL14B-AMN 25 $9.00 DN-2JL14B-AMN 25 $9.00
3-pole DN-3JL14B-A 100 $59.00 DN-3JL14B-A 100 $59.00
Blue DN-3JL14B-AMN 25 $12.50 DN-3JL14B-AMN 25 $12.50 55 mm
[2.17 in]
12-pole Blue DN-12JL14B-A 10 $15.00 DN-12JL14B-A 10 $15.00
Jumpers
2-pole DN-2JL14-A 100 $39.00 DN-2JL14-A 100 $39.00
Red DN-2JL14-AMN 25 $9.00 DN-2JL14-AMN 25 $9.00
78 mm 5.3 mm
3-pole DN-3JL14-A 100 $59.00 DN-3JL14-A 100 $59.00 [3.08 in] [0.21 in]
Red DN-3JL14-AMN 25 $12.50 DN-3JL14-AMN 25 $12.50
12-pole Red DN-12JL14-A 10 $15.00 DN-12JL14-A 100 $15.00
Jumper Cutting Tool DN-JL14CUT 1 $65.00 DN-JL14CUT 1 $65.00
DN-TL14S-A
7.5 mm DN-R35S1 10 $28.00 DN-R35S1 10 $28.00
35mm high DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00
DIN Rail 15mm DN-R35HS1 10 $49.50 DN-R35HS1 10 $49.50
high DN-R35HS1-2 2 $12.00 DN-R35HS1-2 2 $12.00
55 mm
DN-EB35 50 $39.50 DN-EB35 50 $39.50 [2.17 in]
DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00
DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50
End Brackets
DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50
62 mm 5.3 mm
DN-QEB35 50 $25.50 DN-QEB35 50 $25.50 [2.44 in] [0.21 in]
DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50
Angled Support Bracket DN-ASB1 50 $49.50 DN-ASB1 50 $49.50
Marking Tags DN-LAT-A series 500 various DN-LAT-A series 500 various
*Copper wire only
For more more information on accessories, see the DINnectors Accessories section of this chapter.
A W ire the bottom two levels of one D C onnect the power supply terminals
DN‑TL14-A to connect your power of the DN-TL14-A to the LED sensor
supply to what will become a sensor +V terminal blocks by installing jumpers.
and -V power bus. This will create a +V and -V power
bus on the two bottom levels of the
B Mount the triple-level sensor blocks next to terminals. Use an external wire to
the DN-TL14-A. The DN‑TL14S-A is our
standard sensor terminal block. connect a group of 12
The DN-TL14SLP-A gives you LED DN-TL14-As to another group.
indication for PNP sensors, and the
DN‑TL14SLN-A gives you LED indication for E W ire the sensor signal lines through
the top levels of the blocks to your
NPN sensors. PLC or controller. Remember to use
the appropriate end covers to cover
C U se the top level to connect the first
sensor signal line to the PLC. any exposed metal parts for safety
purposes.
D PNP
Signal
C
A -
Power -
Supply + +
DN-3JL14B-A
DN-TL14-A
NPN
PLC or Signal
B
Controller
-
+
DN-3JL14-A
DN-TL14SLN-A
NPN
E Signal
DN-TL14SLN-A
Note: Wiring schematic is for reference only. See individual I/O modules for correct wiring connections.
DN-TL14SLP-A DN-TL14SLN-A
Series: EURO Z 2.5 LP/35 Series: EURO Z 2.5 LN/35 55 mm
[2.17 in]
Ordering Information
Part Number Pcs/Pkg Price Part Number Pcs/Pkg Price
Color Gray DN-TL14SLP-A 25 $70.00 DN-TL14SLN-A 25 $70.00
62 mm 5.3 mm
Technical Specifications [2.44 in] [0.21 in]
Stripping Length 10 mm [0.39 in] 10 mm [0.39 in]
Tightening Torque 0.5 N·m [4.5 lb·in] 0.5 N·m [4.5 lb·in]
Density 200/m [57 pcs/ft] 200/m [57 pcs/ft]
Leakage Current 25mA@5V 25mA@5V
DN-TL14SLN-A
LED Voltage/Resistance 12 – 24V AC/DC. 3.4 kΩ 12 – 24V AC/DC. 3.4 kΩ
UL Approval* 300V 10A 26-14 AWG 300V 10A 26-14 AWG
CSA Approval 300V 10A 26-14 AWG 300V 10A 26-14 AWG
VDE Approval 300V 10A 2.5 mm² 300V 10A 2.5 mm²
55 mm
Ambient air temperature: -20°C to 105°C [-4°F to 221°F]
Operating Temperature Relative humidity: 50% max at 40°C [104°F]; 90% max at 20°C [68°F] [2.17 in]
10kA per Table SB4.1, 2009, UL 508A,
SCCR Rating Maximum short circuit current rating for unmarked components
CE Conformity CE (EN 60947-1 / EN 60947-7-1)
62 mm 5.3 mm
Agency File # UL E179129 [2.44 in] [0.21 in]
Note: To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number's web page.
Accessories
End Cover DN-EC14S 25 $9.00 DN-EC14S 25 $9.00
2-pole DN-2JL14B-A 100 $39.00 DN-2JL14B-A 100 $39.00
Blue DN-2JL14B-AMN 25 $9.00 DN-2JL14B-AMN 25 $9.00
3-pole DN-3JL14B-A 100 $59.00 DN-3JL14B-A 100 $59.00
Blue DN-3JL14B-AMN 25 $12.50 DN-3JL14B-AMN 25 $12.50
12-pole Blue DN-12JL14B-A 10 $15.00 DN-12JL14B-A 10 $15.00
Jumpers
2-pole DN-2JL14-A 100 $39.00 DN-2JL14-A 100 $39.00
Red DN-2JL14-AMN 25 $9.00 DN-2JL14-AMN 25 $9.00
3-pole DN-3JL14-A 100 $59.00 DN-3JL14-A 100 $59.00
Red DN-3JL14-AMN 25 $12.50 DN-3JL14-AMN 25 $12.50
12-pole Red DN-12JL14-A 10 $15.00 DN-12JL14-A 10 $15.00
Jumper Cutting Tool DN-JL14CUT 1 $65.00 DN-JL14CUT 1 $65.00
7.5 mm DN-R35S1 10 $28.00 DN-R35S1 10 $28.00
35mm high DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00
DIN Rail 15mm DN-R35HS1 10 $49.50 DN-R35HS1 10 $49.50
high DN-R35HS1-2 2 $12.00 DN-R35HS1-2 2 $12.00
DN-EB35 50 $39.50 DN-EB35 50 $39.50
DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00
DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50
End Brackets
DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50
DN-QEB35 50 $25.50 DN-QEB35 50 $25.50
DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50
Angled Support Bracket DN-ASB1 50 $49.50 DN-ASB1 50 $49.50
Marking Tags DN-LAT-A series 500 various DN-LAT-A series 500 various
*Copper wire only
For more information on accessories, see the DINnectors Accessories section of this chapter.
DN-THERM2 / DN-THERM2MN
6.0 mm
Clamping Yoke 42.0 mm [0.24 in]
[1.65 in]
27.5 mm
[1.08 in]
Accessories
DN-EMXM1EC1
left (open) side 25 $8.50 DN-EMXDVEC1 25 $8.50
End Cover right (closed) side
DN-EMXM1EC2 25 $8.50 DN-EMXDVEC2 25 $8.50
Spacer Either side DN-EMXM1SPA1 25 $7.25 DN-EMXDVSPA1 25 $8.25
(4) DN-EMXDV (4) DN-EMXDV with
7.5 mm DN-R35S1 10 $28.00 DN-R35S1 10 $28.00
Series: EURO XDV 2.5/35 (2) DN-4PLUG
35mm high DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00
DIN Rail 15mm DN-R35HS1 10 $49.50 DN-R35HS1 10 $49.50 DN-EMXM1
high DN-R35HS1-2 2 $12.00 DN-R35HS1-2 2 $12.00
DN-2J2Y 100 $26.00 DN-2J2Y 100 $26.00
29.5 mm
[1.16 in]
2-pole
DN-2J2YMN 25 $7.50 DN-2J2YMN 25 $7.50
Jumpers** DN-3J2Y 100 $36.50 DN-3J2Y 100 $36.50
3-pole
DN-3J2YMN 25 $10.25 DN-3J2YMN 25 $10.25
24-pole DN-24J2Y 1 $16.00 DN-24J2Y 1 $16.00
Jumper Cutting Tool** DN-J2CUT 1 $46.50 DN-J2CUT 1 $46.50 59.0 mm 5.0 mm
[2.32 in] [0.20 in]
Pin Protector – 4-pole DN-EMPEG1 Each piece covers and protects up to 4 unused pins $2.50
DN-EB35 50 $39.50 DN-EB35 50 $39.50 DN-EMXDV
DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00
DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50
End Brackets
DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50
52.0 mm
[2.05 in]
DN-M10-A DN-MG10
Series: EURO 4/15 Series: EURO E4/15
Ordering Information
Part Number Pcs/Pkg Price Part Number Pcs/Pkg Price
Gray Block DN-M10-A 100 $58.00 – – –
Blue Block DN-M10B-A 100 $78.00 – – –
Green/Yellow Block – – – DN-MG10 20 $47.50
Technical Specifications
Stripping Length 10mm [0.39 in] 10mm [0.39 in] DN-M10-A
Tightening Torque 0.6 N·m [5.3 lb·in] 0.6 N·m [5.3 lb·in]
Density 142/m [43 pcs/ft] 166/m [50 pcs/ft]
CE Conformity LVD 2006/95/EC LVD 2006/95/EC
UL Approval* 300V 30A 24-10 AWG – – 18-10 AWG
28 mm
CSA Approval 300V 30A 24-10 AWG – – 18-10 AWG [1.10 in]
VDE Approval 400V 32A 4mm² – – 4mm²
Ambient air temperature: -20°C to 105°C [-4°F to 221°F]
Operating Temperature Relative humidity: 50% max at 40°C [104°F]; 90% max at 20°C [68°F]
10kA per Table SB4.1, 2009, UL 508A, 32 mm 6 mm
SCCR Rating Maximum short circuit current rating for unmarked components [1.26 in] [0.24 in]
CE Conformity CE (EN 60947-1 / EN 60947-7-1)
Agency File # UL E179129 DN-MG10
Note: To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number's web page.
Accessories
DN-ECM10 100 $26.00
End Covers
DN-ECM10MN 25 $8.00 31.5 mm
DN-2J4Y 100 $27.50 [1.24 in]
2-pole
DN-2J4YMN 25 $8.00
Jumpers DN-3J4Y 100 $43.50
3-pole
DN-3J4YMN 25 $12.00 32 mm 6 mm
– [1.26 in] [0.24 in]
24-pole DN-24J4Y 5 $17.00
Jumper Cutting Tool** DN-J4CUT 1 $46.50
DN-MC10 100 $37.50
Top Cover
DN-MC10MN 25 $7.75
Test Plug/Red DN-TPR 10 $24.50
Test Plug/Black DN-TPB 10 $24.50
DN-R15S1 DN-R15S1
15mm DIN Rail 5.5high
mm 10 $26.00 10 $26.00
DN-R15S1-2 2 $8.00 DN-R15S1-2 2 $8.00
DN-EB15 100 $64.00
End Brackets –
DN-EB15MN 20 $14.00
Angled Support Bracket DN-ASB1 50 $49.50 DN-ASB1 50 $49.50
Marking Tags DN-LT series 100 various DN-LT series 100 various
* For copper wire only
** Jumper cutting tool DN-J4CUT cuts DN-xJ4Y Series multi-pole jumpers and MAINTAINS THE JUMPER INSULATIONS.
Note: For more information on accessories, see the DINnectors Accessories section of this chapter.
Ordering Information
Part Number Pcs/Pkg Price Part Number Pcs/Pkg Price Part Number Pcs/Pkg Price
Green/Yellow DN-G10 50 $115.00DN-G8 50 $138.00DN-G6 50 $188.00
Terminal Block DN-G10-10 10 $24.50 DN-G8-10 10 $29.50 DN-G6-10 10 $40.00
Technical Specifications
Stripping Length 10mm [0.39 in] 12mm [0.47 in] 13mm [0.51]
Tightening Torque 0.8 N·m [7 lb·in] 1.1 N·m [10 lb·in] 2.3 N·m [20 lb·in]
Ground Screw Torque – 0.8 N·m [7 lb·in] –
Density 142/m [43 pcs/ft] 125/m [38 pcs/ft] 100/m [30 pcs/ft]
UL Approval* – – 24-10 AWG – – 22-8 AWG – – 20-6 AWG
CSA Approval – – 18-12 AWG – – 18-8 AWG – – 18-6 AWG
VDE Approval – – 4mm² – – 6mm² – – 10mm²
Operating Temperature Ambient air temperature: -20°C to 105°C [-4°F to 221°F] / Relative humidity: 50% max at 40°C [104°F]; 90% max at 20°C [68°F]
SCCR Rating 10kA per Table SB4.1, 2009, UL 508A, Maximum short circuit current rating for unmarked components
CE Conformity CE (EN 60947-1 / EN 60947-7-2)
Agency File # UL E179129 / LR84816
Note: To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number's web page.
Accessories
7.5 mm DN-R35S1 10 $28.00 DN-R35S1 10 $28.00 DN-R35S1 10 $28.00
35mm high DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00
DIN Rail 15mm DN-R35HS1 10 $49.50 DN-R35HS1 10 $49.50 DN-R35HS1 10 $49.50
high DN-R35HS1-2 2 $12.00 DN-R35HS1-2 2 $12.00 DN-R35HS1-2 2 $12.00
Angled Support Bracket DN-ASB1 50 $49.50 DN-ASB1 50 $49.50 DN-ASB1 50 $49.50
44 mm 36 mm
44 mm [1.42 in]
[1.73 in] [1.73 in]
58 mm 7 mm
58 mm 10 mm 58 mm 8 mm [2.28 in] [0.28 in]
[2.28 in] [0.39 in] [2.28 in] [0.31 in]
Ordering Information
Part Number Pcs/Pkg Price Part Number Pcs/Pkg Price
DN-G4 25 $115.00DN-G1/0 25 $147.00
Green/Yellow Block
DN-G4MN 8 $27.25 DN-G1/0MN 5 $23.75
Technical Specifications
Stripping Length 14mm [0.55 in] 18mm [0.71]
Tightening Torque 3.4 N·m [30 lb·in] 5.1 N·m [45 lb·in]
Ground Screw Torque 1.1 N·m [10 lb·in] 1.1 N·m [10 lb·in]
Density 83/m [25 pcs/ft] 62/m [19 pcs/ft]
UL Approval* – 14-4 AWG – – 14-1/0 AWG
CSA Approval – – 14-4 AWG – – 14-1/0 AWG
VDE Approval – – 25mm² – – 35mm²
SCCR Rating 10kA per Table SB4.1, 2009, UL 508A, Maximum short circuit current rating for unmarked components
CE Conformity CE (EN 60947-1 / 60947-7-2)
Agency File # UL E179129 / LR84816
Note: To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number's web page.
Accessories
7.5 mm DN-R35S1 10 $28.00 DN-R35S1 10 $28.00
35mm high DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00
DIN Rail 15mm DN-R35HS1 10 $49.50 DN-R35HS1 10 $49.50
high DN-R35HS1-2 2 $12.00 DN-R35HS1-2 2 $12.00
Angled Support Bracket DN-ASB1 50 $49.50 DN-ASB1 50 $49.50
49 mm
[1.93 in] 60 mm
[2.36 in]
58 mm 12 mm 62 mm 16 mm
[2.28 in] [0.47 in] [2.44 in] [0.63 in]
Ordering Information
Part Pcs/ Price Part Pcs/ Price Part Pcs/ Price Part Pcs/ Price
Number Pkg Number Pkg Number Pkg Number Pkg
DN-F6 25 $93.00 DN-F10 50 $149.00
Gray Terminal Block – –
DN-F6MN 7 $20.00 DN-F10MN 10 $22.75
12-24 VAC/DC* DN-F6L24 10 $54.00 DN-F10L24 10 $53.00
110 VAC/DC* – DN-F6L110 10 $54.00 – DN-F10L110 10 $53.00
220 VAC/DC* DN-F6L220 10 $54.00 DN-F10L220 10 $53.00
Technical Specifications
Stripping Length 12mm [0.47 in] 12mm [0.47 in] 10mm [0.39 in] 10mm [0.39 in]
Tightening Torque 2.0 N·m [17.7 lb·in] 2.0 N·m [17.7 lb·in] 0.6 N·m [5.3 lb·in] 0.6 N·m [5.3 lb·in]
Density 100/m [30 pcs/ft] 100/m [30 pcs/ft] 100/m [30 pcs/ft] 100/m [30 pcs/ft]
UL Approval** 600V 30A 20-6 AWG 600V 30A 20-6 AWG 300V 15A 24-10 AWG 300V 15A 24-10 AWG
CSA Approval 600V 30A 18-6 AWG 600V 30A 18-6 AWG 300V 8A 18-12 AWG 300V 8A 18-12 AWG
VDE Approval 750V 8A – 750V 8A – 500V 8A 4mm² 500V 8A 4mm²
Fuse Size (not supplied) 1 1/4” X 1/4” 1 1/4” X 1/4” 5x20mm-5x25mm 5x20mm-5x25mm
Indicator Type Non-indicating LED blown fuse indicator Non-indicating LED blown fuse indicator
Operating Temperature Ambient air temperature: -20°C to 85°C [-4°F to 185°F] / Relative humidity: 50% max at 40°C [104°F]; 90% max at 20°C [68°F]
SCCR Rating 10kA per Table SB4.1, 2009, UL 508A, Maximum short circuit current rating for unmarked components
CE Conformity CE (EN 60947-1 / 60947-7-3)
Agency File # UL E179129 / LR84816
Note: To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number's web page.
Accessories
End Covers Included Included Included Included
DN-R35S1
7.5 mm 10 $28.00 DN-R35S1 10 $28.00 DN-R35S1 10 $28.00 DN-R35S1 10 $28.00
35mm high
DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00
DIN Rail 15mmDN-R35HS1 10 $49.50 DN-R35HS1 10 $49.50 DN-R35HS1 10 $49.50 DN-R35HS1 10 $49.50
high
DN-R35HS1-2 2 $12.00 DN-R35HS1-2 2 $12.00 DN-R35HS1-2 2 $12.00 DN-R35HS1-2 2 $12.00
DN-EB35 50 $39.50 DN-EB35 50 $39.50 DN-EB35 50 $39.50 DN-EB35 50 $39.50
DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00
DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50
End Brackets
DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50
DN-QEB35 50 $25.50 DN-QEB35 50 $25.50 DN-QEB35 50 $25.50 DN-QEB35 50 $25.50
DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50
Angled Support Bracket DN-ASB1 50 $49.50 DN-ASB1 50 $49.50 DN-ASB1 50 $49.50 DN-ASB1 50 $49.50
Marking Tags DN-L*** or 500/ various
DN-L*** or 500/ various
DN-L*** or 500/ various DN-L*** or 500/ various
DN-LT**** 100 DN-LT**** 100 DN-LT**** 100 DN-LT**** 100
*Working voltage **For copper wire only ***On lever arm ****On terminal body
Note: DN-F6 series fuse holders will accommodate the following AutomationDirect fuses: ABC, AGC, MDA and MDL Series.
DN-F10 series fuse holders will accommodate the following AutomationDirect fuses: GMA, GMC, S500, and S506 Series.
For more information on accessories, see the DINnectors Accessories section of this chapter.
44 mm 44 mm
[1.73 in] [1.73 in]
66 mm 66 mm
[2.6 in] [2.6 in]
10 mm 10 mm
[0.39 in] [0.39 in]
Supplementary Protector /
Disconnect Terminal Block
Sockets mm mm
in in
5/ 4
F2. sc. 5/F
i F2. ocket
d c. s
F4 ket dis /LED
mm
soc
in
w
DN-DIS series Disconnect Terminal
Blocks offer the flexibility of opening
mm
in
Ordering Information
Trip Indicator Pcs/
Part Number Trip Indicator Pcs/
Pkg Price Part Number Pkg Price
DN-DIS2 – 50 $75.00 DN-DIS4 – 50 $75.00
DN-DIS2MN – 10 $18.25 DN-DIS4MN – 10 $18.25
Gray Socket with DN-DIS2L12 12 VAC/DC LED 50 $77.00 DN-DIS4L12 12 VAC/DC LED 50 $77.00
Disconnect DN-DIS2L12MN 12 VAC/DC LED 10 $21.75 DN-DIS4L12MN 12 VAC/DC LED 10 $21.75
DN-DIS2L24 24 VAC/DC LED 50 $96.50 DN-DIS4L24 24 VAC/DC LED 50 $77.00
DN-DIS2L24MN 24 VAC/DC LED 10 $21.75 DN-DIS4L24MN 24 VAC/DC LED 10 $21.75
Technical Specifications
Stripping Length 5mm [0.20 in] 6mm [0.24 in]
Tightening Torque 0.5 N·m [4.4 lb·in] 0.8 N·m [7 lb·in]
10A with SUPP 24-12 10A with SUPP 24-10
UL Approval* 300V
20A with disconnect AWG*
300V
25A with disconnect AWG*
Ambient air temperature: -20°C to 85°C [-4°F to 185°F]
Operating Temperature Relative humidity: 50% max at 40°C [104°F]; 90% max at 20°C [68°F]
10kA per Table SB4.1, 2009, UL 508A,
SCCR Rating Maximum short circuit current rating for unmarked components
CE Conformity CE (EN 60947-1 / 60947-7-3)
Agency File # UL E179129
Note: To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number's web page.
Accessories
End Cover/ DN-FESPA 50 $15.00 DN-FESPA 50 $15.00
Spacer** DN-FESPA-10 10 $3.00 DN-FESPA-10 10 $3.00
DN-FESEP 50 $15.00 DN-FESEP 50 $15.00
Separator
DN-FESEP-10 10 $3.00 DN-FESEP-10 10 $3.00
7.5 mm DN-R35S1 10 $28.00 DN-R35S1 10 $28.00
high DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00
35mm DIN Rail
15mm DN-R35HS1 10 $49.50 DN-R35HS1 10 $49.50
high DN-R35HS1-2 2 $12.00 DN-R35HS1-2 2 $12.00
DN-EB35 50 $39.50 DN-EB35 50 $39.50
DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00
DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50
End Brackets
DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50
DN-QEB35 50 $25.50 DN-QEB35 50 $25.50
DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50
Angled Support Bracket DN-ASB1 50 $49.50 DN-ASB1 50 $49.50
DN-DIS-BLADE 50 $21.50 DN-DIS-BLADE 50 $21.50
Disconnect Blade
DN-DIS-BMN 10 $5.50 DN-DIS-BMN 10 $5.50
500/ 500/
Marking Tags DN-LA or DN-LT series 100 various DN-L or DN-LT series 100 various
*For copper wire only
**Use one End Cover / Spacer per DN-FEx Terminal Block Socket when using DN-SUPP-x supplementary protector
Note: For more information on accessories, see the DINnectors Accessories section of this chapter.
(with DN-SUPP-xx)
(with DN-SUPP-xx)
(with DN-SUPP-xx)
78.1 mm
[3.08 in]
34.0 mm
[1.34 in]
When aW
lighneend aalliogne,duasleone, u s e When aW
lighneend ainligane
rodwin
, uaserow, use
55.8 mm 5.0 mm 6.0 mm DN-FESD ENP-FESEP 2pcs DN2-pFcE s SDPNA-FfoErSD PNA -fFoEr 2DN-FE2
[2.20 in] [0.20 in] [0.24 in]
2pcs DN 2p-FcE
s SDENP-FfoErSD ENP -fFoE4
r DN-FE4
DN-FE2, DN-FE2Lxx DN-FE2xxx DN-FE4xxx
DN-FE4, DN-FE4Lxx
DN-DIS-xxx dimensions are the same as DN-FExxx dimensions.
Supplementary Protectors
for Terminal Block Sockets
Supplementary Protectors
Rated Internal Fits Pcs Price
Part Number Reference Current Type
Resistance Socket /Pkg /Pkg
DN-SUPP-P25 20 $197.00
435T0025 0.25 A 14Ω
DN-SUPP-P25-1 1 $10.00
DN-SUPP-P5 20 $197.00
435T0050 0.5 A 3.4 Ω
DN-SUPP-P5-1 1 $10.00
DN-SUPP-1 20 $197.00
435T0100 1A 0.9 Ω
DN-SUPP-1-1 1 $10.00
DN-SUPP-2 Terminal 20 $197.00
435T0200 2A 0.25 Ω Block Socket DN-SUPP-x
DN-SUPP-2-1 UL1077 Types: 1 $10.00 Supplementary Protector
DN-SUPP-3 Single Pole DN-FEx 20 $197.00 (plugs into DN-FE EURO F series socket)
435T0300 3A 0.11 Ω Push On or
DN-SUPP-3-1 Push Off DN-DISx if 1 $10.00
OFF
DN-SUPP-4 Push to Reset disconnect 20 $197.00
435T0400 4A 0.07 Ω blade is
DN-SUPP-4-1 removed 1 $10.00
[43.7 mm]
DN-SUPP-6
1.72 in
20 $197.00
[8.6 mm]
435T0600 6A
0.34 in
DN-SUPP-6-1 1 $10.00
DN-SUPP-8 20 $197.00
435T0800 8A ≤0.05 Ω
DN-SUPP-8-1 1 $10.00
DN-SUPP-10 20 $197.00
435T1000 10A 0.21 in
DN-SUPP-10-1 1 $10.00 [5.2 mm]
[6.4 mm]
0.25 in
0.32 in
[8.2 mm] 0.57 in
[14.5 mm]
[24.4 mm]
0.78 in
0.96 in
Supplementary Protector Specifications [19.8 mm]
Ordering Information
Part Number Pcs/Pkg Price Part Number Pcs/Pkg Price
DN-DIS10 50 $162.00DN-KBD12 50 $90.00
Gray Disconnect Block
DN-DIS10MN 10 $26.25 DN-KBD12MN 10 $14.50
Technical Specifications
Stripping Length 10mm [0.39 in] 10mm [0.39 in]
Tightening Torque 0.6 N·m [5.3 lb·in] 0.5 N·m [4.4 lb·in]
Density 125/m [30 pcs/ft] 200/m [60 pcs/ft]
UL Approval* 300V 30A 24-10 AWG 600V 20A 22-12 AWG
CSA Approval 300V 25A 18-12 AWG 600V 16A 18-12 AWG
VDE Approval 500V 25A 4mm² 600V 16A 2.5 mm²
Disconnect Type Copper bar Copper blade
Ambient air temperature: -20°C to 85°C [-4°F to 185°F]
Operating Temperature Relative humidity: 50% max at 40°C [104°F]; 90% max at 20°C [68°F]
SCCR Rating 10kA per Table SB4.1, 2009, UL 508A, Maximum short circuit current rating for unmarked components
CE Conformity CE (EN 60947-1 / EN 60947-7-3) CE (EN 60947-1 / EN 60947-7-1)
Agency File # UL E179129 / LR84816
Note: To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number's web page.
Accessories
DN-ECKBD 100 $26.00
End Cover Included
DN-ECKBDMN 10 $3.75
DN-R35S1
7.5 mm 10 $28.00 DN-R35S1 10 $28.00
35mm high
DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00
DIN Rail DN-R35HS1
15mm 10 $49.50 DN-R35HS1 10 $49.50
high
DN-R35HS1-2 2 $12.00 DN-R35HS1-2 2 $12.00
DN-EB35 50 $39.50 DN-EB35 50 $39.50
DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00
DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50
End Bracket
DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50
DN-QEB35 50 $25.50 DN-QEB35 50 $25.50
DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50
Angled Support Bracket DN-ASB1 50 $49.50 DN-ASB1 50 $49.50
DN-DIS10 / DN-DIS10MN
DN-KBD12 / DN-KBD12MN
35 mm
44 mm [1.38 in]
[1.73 in]
52 mm 5 mm
66 mm 10 mm
[2.05 in] [0.20 in]
[2.6 in] [0.39 in]
Cross Reference
Allen-Bradley®
The following is a list of comparable but overpriced competitor products. To obtain our high-quality DINnectors, simply find the
corresponding part number of the unit you currently use. These are approximate replacements based on UL wire size, ampacity
and voltage. Please consult the technical section for specifications to determine suitability for your application. Physical size var-
ies from manufacturer to manufacturer.
Cross Reference
Entrelec®
The following is a list of comparable but overpriced competitor products. To obtain our high-quality DINnectors, simply find the
corresponding part number of the unit you currently use. These are approximate replacements based on UL wire size, ampacity
and voltage: please consult the technical section for specifications to determine suitability for your application. Physical size var-
ies from manufacturer to manufacturer.
Cross Reference
Phoenix Contact®
The following is a list of comparable but overpriced competitor products. To obtain our high-quality DINnectors, simply find the
corresponding part number of the unit you currently use. These are approximate replacements based on UL wire size, ampacity
and voltage. Please consult the technical section for specifications to determine suitability for your application. Physical size var-
ies from manufacturer to manufacturer.
Cross Reference
Weidmuller®
The following is a list of comparable but overpriced competitor products. To obtain our high-quality DINnectors, simply find the
corresponding part number of the unit you currently use. These are approximate replacements based on UL wire size, ampacity
and voltage. Please consult the technical section for specifications to determine suitability for your application. Physical size var-
ies from manufacturer to manufacturer.
Cross Reference
Weidmuller®
The following is a list of comparable but overpriced competitor products. To obtain our high-quality DINnectors, simply find the
corresponding part number of the unit you currently use. These are approximate replacements based on UL wire size, ampacity
and voltage. Please consult the technical section for specifications to determine suitability for your application. Physical size varies
from manufacturer to manufacturer .
Screwless At a Glance
Feed-through terminal blocks are available in a number of wire size options to ensure
Feed-through Terminal Blocks flexibility and ease of installation for your DIN-rail mounted connection system.
Multi-level Terminal Blocks Double-level terminal blocks offer twice the wiring density of feed-through blocks.
Ground terminal blocks are used to mechanically and electrically connect wires to the
Ground Terminal Blocks DIN rail, thus allowing the rail to function as a ground bus bar.
Disconnect Terminal Block Plug-in Terminal Blocks Marking Tags & Accessories
2
1
1 2 Removal
Push down util
Properly align jumper bar
firmly seated.
with terminal block center
jumper slots.
CLICK!
Yes No
o Yes = Good, acceptable jumper
No = Bad, damaged jumper
Screwless Feed-Through
Terminal Blocks
Feed-through terminal blocks
provide the means to connect two
wires together, and are available
in sizes suitable for up to 8AWG DN-Q12-A
DN-Q10B-A DN-Q8-A
wire. These terminal blocks are (Euro Q2.5/35)
(Euro Q4/35) (Euro Q6/35)
35mm DIN-rail mountable.
Ordering Information
Part Number Pcs/Pkg Price Part Number Pcs/Pkg Price Part Number Pcs/Pkg Price
Gray Terminal Block DN-Q12-A 50 $24.50 DN-Q10-A 50 $24.00 DN-Q8-A 50 $38.00
Blue Terminal Block DN-Q12B-A 50 $26.50 DN-Q10B-A 50 $26.50 DN-Q8B-A 50 $41.00
Description Screwless feed-through terminal blocks Screwless feed-through terminal blocks Screwless feed-through terminal blocks
Technical Specifications
Stripping Length 12mm [0.47 in] 15mm [0.59 in] 18mm [0.71]
Density 200/m [60 pcs/ft] 166/m [50 pcs/ft] 125/m [38 pcs/ft]
UL Approval* 600V 20A 24-12 AWG 600V 30A 24-10 AWG 600V 45A 22-8 AWG
CSA Approval 600V 20A 24-12 AWG 600V 30A 24-10 AWG 600V 45A 22-8 AWG
VDE Approval 630V 24A 2.5 mm² 630V 32A 4mm² 630V 41A 6mm²
Operating Temperature Ambient air temperature: -20°C to 105°C [-4°F to 221°F] / Relative humidity: 50% max at 40°C [104°F]; 90% max at 20°C [68°F]
SCCR Rating 10kA per Table SB4.1, 2009, UL 508A, Maximum short circuit current rating for unmarked components
CE Conformity CE (EN 60947-1 / EN 60947-7-1)
Agency File # UL E179129
Note: To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number's web page.
Accessories
DN-QEC12 50 $12.00 DN-QEC10 50 $12.00 DN-QEC8 50 $14.00
End Covers
DN-QEC12MN 10 $3.25 DN-QEC10MN 10 $3.25 DN-QEC8MN 10 $3.50
DN-2J2Y 100 $26.00 DN-2J4Y 100 $27.50 DN-2J6Y 100 $34.50
2-pole
DN-2J2YMN 25 $7.50 DN-2J4YMN 25 $8.00 DN-2J6YMN 25 $9.00
Jumpers DN-3J2Y 100 $36.50 DN-3J4Y 100 $43.50 DN-3J6Y 100 $50.00
3-pole
DN-3J2YMN 25 $10.25 DN-3J4YMN 25 $12.00 DN-3J6YMN 25 $13.00
Multi-pole DN-24J2Y 5 $16.00 DN-24J4Y 5 $17.00 DN-12J6Y 10 $21.00
Jumper Cutting Tool DN-J2CUT 1 $46.50 DN-J4CUT 1 $46.50 –
35mm 7.5 mm DN-R35S1 10 $28.00 DN-R35S1 10 $28.00 DN-R35S1 10 $28.00
DIN Rail high DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00
DN-EB35 50 $39.50 DN-EB35 50 $39.50 DN-EB35 50 $39.50
DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00
DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50
End Brackets
DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50
DN-QEB35 50 $25.50 DN-QEB35 50 $25.50 DN-QEB35 50 $25.50
DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50
Angled Support Bracket DN-ASB1 50 $49.50 DN-ASB1 50 $49.50 DN-ASB1 50 $49.50
Marking Tags DN-QL Series 500 various DN-QL Series 500 various DN-QL Series 500 various
*Copper wire only
Note: For more information on accessories, see the DINnectors Accessories section of this chapter.
Dimensions
DN-Q12-A DN-Q10-A DN-Q8-A
mm mm
mm mm
in in
mm mm in in
in in
mm mm
mm mm
mm
in in
in in
in
Screwless Double-Level
Terminal Blocks
DN-QD12-A DN-QD12X-A LED version Diode version
Double-level terminal blocks offer twice This style is available with LED indicator Typically, an inductive load produces a
the wiring density of feed-through blocks. installed. The LED illuminates when volt- spike when it is turned off. These terminal
The DN-QD12X-A version is supplied age is present. The DN-QD12L2-A ver- blocks with built-in diode help protect
with an internal jumper to common all sion is for 12 - 24 VAC/DC circuits, and your PLC’s output circuits. (Please see
four of its connection points. includes current limiting elements. application note AN-MISC-032 at
DN-QD12X-A DN-QD12L2-A http://support.automationdirect.com/
(Euro QD2.5/35) (Euro QD2.5/35) docs/an-misc-032.pdf
DN-QD12DR-A
(Euro QD2.5/35)
Ordering Information
Part Pcs/ Price Part Pcs/ Price Part Pcs/ Price Part Pcs/ Price
Number Pkg Number Pkg Number Pkg Number Pkg
Gray Terminal Blk DN-QD12-A 25 $35.50 DN-QD12X-A 10 $23.50 DN-QD12L2-A 10 $24.50 DN-QD12DR-A 10 $23.50
Blue Terminal Blk DN-QD12B-A 25 $37.50 DN-QD12XB-A 10 $25.50 – –
Double-level screwless Double-level screwless cross- Double-level screwless terminal blocks w/ Double-level screwless terminal blocks
Description terminal blocks connected terminal blocks LED installed for visual circuit indication w/diode installed for circuit protection
Technical Specifications
Stripping Length 12mm [0.47 in] 12mm [0.47 in] 12mm [0.47 in] 12mm [0.47 in]
Density 200/m [60 pcs/ft] 200/m [60 pcs/ft] 200/m [60 pcs/ft] 200/m [60 pcs/ft]
UL Approval* 600V 20A 24-12 AWG 600V 20A 24-12AWG 600V 20A 24-12 AWG 600V 1A diode 24-12 AWG
CSA Approval 600V 20A 24-12 AWG 600V 20A 24-12AWG 600V 20A 24-12 AWG 600V 1A diode 24-12 AWG
VDE Approval 500V 24A 2.5 mm² 500V 24A 2.5 mm² 500V 24A 2.5 mm² 500V 1A diode 2.5 mm²
LED Voltage – – 12 -24 VAC/DC. 3.4 kΩ –
Operating Temp Ambient air temperature: -20°C to 105°C [-4°F to 221°F] / Relative humidity: 50% max at 40°C [104°F]; 90% max at 20°C [68°F]
SCCR Rating 10kA per Table SB4.1, 2009, UL 508A, Maximum short circuit current rating for unmarked components
CE Conformity CE (EN 60947-1 / EN 60947-7-1)
Agency File # UL E179129
Note: To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number's web page.
Accessories
End Covers DN-QDEC12 25 $9.75 DN-QDEC12 25 $9.75 DN-QDEC12 25 $9.75 DN-QDEC12 25 $9.75
DN-2J2Y 100 $26.00 DN-2J2Y 100 $26.00 DN-2J2Y 100 $26.00 DN-2J2Y 100 $26.00
2-pole
DN-2J2YMN 25 $7.50 DN-2J2YMN 25 $7.50 DN-2J2YMN 25 $7.50 DN-2J2YMN 25 $7.50
Jumpers DN-3J2Y 100 $36.50 DN-3J2Y 100 $36.50 DN-3J2Y 100 $36.50 DN-3J2Y 100 $36.50
3-pole
DN-3J2YMN 25 $10.25 DN-3J2YMN 25 $10.25 DN-3J2YMN 25 $10.25 DN-3J2YMN 25 $10.25
24-pole DN-24J2Y 5 $16.00 DN-24J2Y 5 $16.00 DN-24J2Y 5 $16.00 DN-24J2Y 5 $16.00
Cutting Tool DN-J2CUT 1 $46.50 DN-J2CUT 1 $46.50 DN-J2CUT 1 $46.50 DN-J2CUT 1 $46.50
35mm 7.5 mm DN-R35S1 10 $28.00 DN-R35S1 10 $28.00 DN-R35S1 10 $28.00 DN-R35S1 10 $28.00
DIN Rail high DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00
DN-EB35 50 $39.50 DN-EB35 50 $39.50 DN-EB35 50 $39.50 DN-EB35 50 $39.50
DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00
DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50
End Brackets
DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50
DN-QEB35 50 $25.50 DN-QEB35 50 $25.50 DN-QEB35 50 $25.50 DN-QEB35 50 $25.50
DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50
Angled DN-ASB1 50 $49.50 DN-ASB1 50 $49.50 DN-ASB1 50 $49.50 DN-ASB1 50 $49.50
Support Bracket
Marking Tags DN-QL Series 500 various DN-QL Series 500 various DN-QL Series 500 various DN-QL Series 500 various
*Copper wire only
For more information on accessories, see the DINnectors Accessories section of this chapter.
98 mm 5 mm
DN-QD12-A Series
Dimensions [3.86 in] [0.2 in]
Note: Jumpering and testing capability on
bottom level only, for DN-QD12X,
DN-QD12L2 and DN-QD12DR.
37.5 mm 2 2
[1.48 in] /
Screwless One-Connection
to Two-Connection Terminal Blocks
Unlike screw terminal blocks, screwless terminal block spring These versions allow multiple wires to be connected together by
clamps are designed to clamp a single wire. If your application way of multiple spring clamps and are 35mm DIN-rail mount-
requires multiple wires to be tied together, we offer multiple able. LED and diode variations are also available in this style.
versions, including one-to-two and two-to-two models.
Marking Tags DN-QL Series 500 various DN-QL Series 500 various DN-QL Series 500 various DN-QL Series 500 various
For more information on accessories, see the DINnectors Accessories section of this chapter.
* Copper wire only.
Screwless One-Connection
to Two-Connection Terminal Blocks
1N4007 Diode Information
RMS Reverse Voltage* V (Rrms) 600V
Average Rectified Forward Current Single Phase, I (O) 1.0 A
Resistive Load, 60Hz
Non-Repetitive Peak Surge Current
(Surge applied at rated load) I (FSM) 30A (1 cycle)
Dimensions
mm [inches] DN-Q12-1-2-A
DN-Q12-1-2L1-A
DN-Q12-1-2L2-A
DN-Q12-1-2DR-A
Screwless Knife-Blade
Disconnect Terminal Blocks
Dimensions
68.5 mm 5 mm
[2.70 in] [0.2 in]
Specifications
Wire Strip Length 12mm [0.47 in]
Density 200/m [60 pcs/ft]
UL Approval* 600V 20A 24-12 AWG
CSA Approval 600V 20A 24-12 AWG
VDE Approval 630V 24A 2.5 mm²
Ambient air temperature: -20°C to 85°C [-4°F to 185°F]
Operating Temperature Relative humidity: 50% max at 40°C [104°F]; 90% max at 20°C [68°F]
10kA per Table SB4.1, 2009, UL 508A,
SCCR Maximum short circuit current rating for unmarked components
CE Conformity CE (EN 60947-1 / EN 60947-7-1)
Agency File # UL E179129
Note: To obtain the most current agency approval information, see the Agency Approval Checklist
section on the specific part number's web page.
Accessories
Pcs/
Part Number Price
Pkg
End Cover DN-QEC12-1-2 25 $8.75
DN-2J2Y 100 $26.00
2-pole
DN-2J2YMN 25 $7.50
Jumpers DN-3J2Y 100 $36.50
3-pole
DN-3J2YMN 25 $10.25
24-pole DN-24J2Y 5 $16.00
Jumper Cutting Tool DN-J2CUT 1 $46.50
35mm 7.5 mm DN-R35S1 10 $28.00
DIN Rail high DN-R35S1-2 2 $9.00
DN-EB35 50 $39.50
DN-EB35MN 20 $18.00
DN-EB35-A 50 $28.50
End Brackets
DN-EB35-A-10 10 $7.50
DN-QEB35 50 $25.50
DN-QEB35-10 10 $7.50
Angled Support Bracket DN-ASB1 50 $49.50
Marking Tags DN-QL Series 500 various
For more information on accessories, see the DINnectors Accessories section of this chapter.
* Copper wire only.
Screwless Two-Connection
to Two-Connection Terminal Blocks
DN-Q12-2-2 -A DN-Q12-2-2L2-A
(Euro QM2/2 2.5/35) DN-Q12-2-2D2-A
(Euro QM2/2 2.5/35) (Euro QM2/2 2.5/35)
DN-Q12-2-2*-A
Series
28.5 mm
[1.12 in]
Ordering Information
Pcs/ Part Pcs/ Pcs/
Part Number Price Number Price Part Number Price
Pkg Pkg Pkg
Gray Terminal Block DN-Q12-2-2-A 25 $24.50 DN-Q12-2-2L2-A 10 $25.50 DN-Q12-2-2D2-A 10 $21.50
Blue Terminal Block DN-Q12B-2-2-A 25 $26.50 – –
Two-connection to two-connection Two-connection to two-connection screwless
Two-connection to two-connection screwless screwless
Description terminal block for 24-12 AWG wire terminal block for 24-12 AWG wire. terminal block for 24-12 AWG wire. Reverse
LED installed for visual circuit indication bias diode installed for circuit protection
Technical Specifications
Stripping Length 12mm [0.47 in] 12mm [0.47 in] 12mm [0.47 in]
Density 200/m [60 pcs/ft] 200/m [60 pcs/ft] 200/m [60 pcs/ft]
UL Approval* 600V 20A 24-12 AWG 600V 20A 24-12 AWG 600V 1A Diode 24-12 AWG
CSA Approval 600V 20A 24-12 AWG 600V 20A 24-12 AWG 600V 1A Diode 24-12 AWG
VDE Approval 630V 20A 2.5 mm² 630V 24A 2.5 mm² 630V 1A Diode 2.5 mm²
LED Voltage – 12 - 24 VAC/DC 3.4 kΩ –
Ambient air temperature: -20°C to 105°C [-4°F to 221°F ]
Operating Temperature Relative humidity: 50% max at 40°C [104°F]; 90% max at 20°C [68°F]
SCCR 10kA per Table SB4.1, 2009, UL 508A, Maximum short circuit current rating for unmarked components
CE Conformity CE (EN 60947-1 / EN 60947-7-1)
Agency File # UL E179129
Note: To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number's web page.
Accessories
End Cover DN-QEC12-2-2 25 $9.75 DN-QEC12-2-2 25 $9.75 DN-QEC12-2-2 25 $9.75
DN-2J2Y 100 $26.00
2-pole
DN-2J2YMN 25 $7.50
Jumpers DN-3J2Y 100 $36.50
3 pole – –
DN-3J2YMN 25 $10.25
24-pole DN-24J2Y 5 $16.00
Jumper Cutting Tool DN-J2CUT 1 $46.50
mm DN-R35S1 DN-R35S1 DN-R35S1
DIN Rail 7.5high
10 $28.00 10 $28.00 10 $28.00
DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00
DN-EB35 50 $39.50 DN-EB35 50 $39.50 DN-EB35 50 $39.50
DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00
DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50
End Bracket
DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50
DN-QEB35 50 $25.50 DN-QEB35 50 $25.50 DN-QEB35 50 $25.50
DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50
Angled Support Bracket DN-ASB1 50 $49.50 DN-ASB1 50 $49.50 DN-ASB1 50 $49.50
Marking Tags DN-QL Series 500 various DN-QL Series 500 various DN-QL Series 500 various
For more information on accessories, see the DINnectors Accessories section of this chapter.
* Copper wire only
SCCR Rating 10kA per Table SB4.1, 2009, UL 508A, maximum SCCR for unmarked components
CE Conformity CE (EN 60947-1 / EN 60947-7-1)
Agency File # UL E179129
To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number's web page.
59.0 mm
[2.32 in]
5.0 mm
[0.20 in]
Accessories
DN-EMXM1EC1
left (open) side 25 $8.50 DN-EMXDVEC1 25 $8.50
End Cover right (closed) side
DN-EMXM1EC2 25 $8.50 DN-EMXDVEC2 25 $8.50
Spacer either side DN-EMXM1SPA1 25 $7.25 DN-EMXDVSPA1 25 $8.25
DN-QEMXDV DN-2J2Y 100 $26.00 DN-2J2Y 100 $26.00
2-pole
DN-2J2YMN 25 $7.50 DN-2J2YMN 25 $7.50
Jumpers DN-3J2Y 100 $36.50 DN-3J2Y 100 $36.50
3-pole
DN-3J2YMN 25 $10.25 DN-3J2YMN 25 $10.25
52.0 mm
[2.05 in]
Ordering Information
Part Number Pcs/Pkg Price Part Number Pcs/Pkg Price Part Number Pcs/Pkg Price
Green/Yellow Block DN-QG12 10 $18.50 DN-QG10 10 $19.50 DN-QG8 10 $24.00
Technical Specifications
Stripping Length 12mm [0.47 in] 15mm [0.59 in] 18mm [0.71 in]
Density 200/m [60 pcs/ft] 166/m [50 pcs/ft] 125/m [38 pcs/ft]
UL Approval 24-12 AWG 24-10 AWG 22-8 AWG
CSA Approval 24-12 AWG 24-10 AWG 22-8 AWG
VDE Approval 2.5 mm² 4mm² 6mm²
Operating Temperature Ambient air temperature: -20°C to 105°C [-4°F to 221°F] / Relative humidity: 50% max at 40°C [104°F]; 90% max at 20°C [68°F]
SCCR Rating 10kA per Table SB4.1, 2009, UL 508A, Maximum short circuit current rating for unmarked components
CE Conformity CE (EN 60947-1 / EN 60947-7-2)
Agency File # UL E179129
Note: To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number's web page.
Accessories
DN-QEC12 50 $12.00 DN-QEC10 50 $12.00 DN-QEC8 50 $14.00
End Cover
DN-QEC12MN 10 $3.25 DN-QEC10MN 10 $3.25 DN-QEC8MN 10 $3.50
35mm DN-R35S1 10 $28.00 DN-R35S1 10 $28.00 DN-R35S1 10 $28.00
DIN Rail DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00
DN-EB35 50 $39.50 DN-EB35 50 $39.50 DN-EB35 50 $39.50
DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00
DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50
End Brackets
DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50
DN-QEB35 50 $25.50 DN-QEB35 50 $25.50 DN-QEB35 50 $25.50
DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50
Angled Support Bracket DN-ASB1 50 $49.50 DN-ASB1 50 $49.50 DN-ASB1 50 $49.50
Marking Tags DN-QL Series 500 various DN-QL Series 500 various DN-QL Series 500 various
Note: For more information on accessories, see the DINnectors Accessories section of this chapter.
34.5 mm 36.5 mm
28.5 mm
[1.36 in] [1.52 in]
[1.12 in]
Ordering Information
Part Number Pcs/Pkg Price Part Number Pcs/Pkg Price
Green/Yellow Block DN-QG12-1-2 10 $32.50 DN-QG12-2-2 10 $38.00
Technical Specifications
Stripping Length 12mm [0.47 in] 12mm [0.47 in]
Density 200/m [60 pcs/ft] 200/m [60 pcs/ft]
UL Approval 24-12 AWG 24-12 AWG
CSA Approval 24-12 AWG 24-12 AWG
VDE Approval 2.5 mm² 2.5 mm²
Operating Ambient air temperature: -20°C to 105°C [-4°F to 221°F]
Temperature Relative humidity: 50% max at 40°C [104°F]; 90% max at 20°C [68°F]
10kA per Table SB4.1, 2009, UL 508A,
SCCR Rating Maximum short circuit current rating for unmarked components
CE Conformity CE (EN 60947-1 / EN 60947-7-2)
Agency File # UL E179129
Note: To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number's web page.
Accessories
End Cover DN-QEC12-1-2 25 $8.75 DN-QEC12-2-2 25 $9.75
35mm DN-R35S1 10 $28.00 DN-R35S1 10 $28.00
DIN Rail DN-R35S1-2 2 $9.00 DN-R35S1-2 2 $9.00
DN-EB35 50 $39.50 DN-EB35 50 $39.50
DN-EB35MN 20 $18.00 DN-EB35MN 20 $18.00
DN-EB35-A 50 $28.50 DN-EB35-A 50 $28.50
End Brackets
DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50
DN-QEB35 50 $25.50 DN-QEB35 50 $25.50
DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50
Angled Support Bracket DN-ASB1 50 $49.50 DN-ASB1 50 $49.50
Marking Tags DN-QL Series 500 various DN-QL Series 500 various
Note: For more information of accessories, see the DINnectors Accessories section of this chapter.
28.5 mm 28.5 mm
[1.12 in] [1.12 in]
Accessories
Steel DIN Rails
Features
35mm wide
• Available in 1-meter lengths
• 7.5 mm-high rails primarily
used to mount terminal blocks,
relays, timers and small PLCs such
as the DL05, DL06,
Part Number Pcs/ Price/ Pcs/ Price/ Part Number Pcs/ Price/
DL105, DL205, CLICK, and Part#
Pkg Pkg Pkg Pkg Pkg Pkg
Productivity3000
• 15mm-high rails for mounting larger DIN Rail DN-R35S1 10 $28.00 DN-R35HS1 10 $49.50 DN-R15S1 10 $26.00
and heavier components such as DN-R35S1-2 2 $9.00 DN-R35HS1-2 2 $12.00 DN-R15S1-2 2 $8.00
contactors and larger PLCs
Steel DINnectors Accessories Specifications
15mm wide Steel, slotted, 3’3” [1m] length, Steel, slotted, 3’3” [1m] length, Steel, slotted, 3’3” [1m] length,
• Available in 1-meter lengths Description 35mm [1.38 in] wide, 35mm [1.38 in] wide, 15mm [0.59 in] wide,
7.5 mm [0.30 in] high 15mm [0.59 in] high 5.5 mm [0.22 in] high
• DN‑R15S1 exclusively for mounting
mini terminal blocks such as the Plating Zinc-plated and chromated
DN-M10-A
International EN60715. RoHS
Standards
Suggested
Mounting M6 M6 M4
Screw Type
Accessories
Dimensions mm [inches]
DN-R35HS1
DN-R35S1
DN-R15S1
DN-R35SAL1
DN-R35SAL1-2
DN-R35SAL2-2
Accessories
DIN rail support brackets
• Angled support brackets raise and tilt mounting rails 30 degrees from mounting surface
for easier wiring
• DN-ASB1 plated steel support bracket
• DN-ASB2-10 cold-rolled steel treated with galvanic zinc plating and passivation
DN-ASB1 30˚angled DIN rail support bracket (M6-1.0 screws not included) 50 $49.50
DN-ASB2-10 30˚angled DIN rail support bracket (M6-1.0 screws included) 10 $12.00
DN-SSB25-10 1” [25mm] DIN rail support bracket (M6-1.0 screws included) 10 $17.00
DN-SSB50-10 2” [50mm] DIN rail support bracket (M6-1.0 screws included) 10 $18.25
DN-SSB70-10 2.75” [70mm] DIN rail support bracket (M6-1.0 screws included) 10 $23.00
DN-SSB90-10 3.5” [90mm] DIN rail support bracket (M6-1.0 screws included) 10 $24.25
DN-CLIP-FM4 40 $45.00
DIN rail mounting clip with M4 x 0.7 mm threaded hole
(Screws not included)
DN-CLIP-FM4-5 5 $6.25
DN-CLIP-FM5 40 $49.50
DIN rail mounting clip with M5 x 0.8 mm threaded hole
(Screws not included)
DN-CLIP-FM5-5 5 $7.00
DN-CLIP-FM4 DN-CLIP-FM5
DN-SSB70-10 DN-SSB90-10 DN-CLIP-FM4-5 DN-CLIP-FM5-5
Accessories
DIN Rail Support Brackets and Mounting Clips
Dimensions mm [inches]
DN-ASB1 DN-ASB2-10
DN-CLIP-FM4 DN-CLIP-FM5
Accessories
Jumpers
Multi-pole jumper bars for DINnector terminal blocks
Dimensions
mm [inches]
Accessories
Modifying a DN-24J8 jumper bar to the required number of poles
1) Place the insulating part click
into the jumper bar and
insert screws, based on
number of poles required.
(For instance, in the follow-
ing example, 5 poles are
required). Click into place.
Accessories
Terminal Plugs Accessories – Terminal Plugs
Plugs* Part Pcs/ Price/ Plugs* Part Pcs/Pkg Price/ Number Length
Number Pkg Pkg Number Pkg of Poles mm [in]
DN-2PLUG 200 $67.00 DN-2PLUGMN 10 $4.25 2 10.2 [0.40]
DN-3PLUG 200 $104.00 DN-3PLUGMN 10 $6.25 3 15.2 [0.60]
DN-4PLUG 100 $69.00 DN-4PLUGMN 10 $8.25 4 20.3 [0.80]
DN-5PLUG 100 $70.00 DN-5PLUGMN 10 $10.25 5 25.4 [1.00]
DN-6PLUG 100 $81.00 DN-6PLUGMN 10 $10.25 6 30.5 [1.20]
DN-xxPLUG / DN-xxPLUGMN DN-7PLUG 50 $49.50 DN-7PLUGMN 5 $8.25 7 35.6 [1.40]
14.5 mm
DN-8PLUG 50 $68.00 DN-8PLUGMN 5 $8.25 8 40.6 [1.60]
[0.57 in] DN-9PLUG 50 $63.25 DN-9PLUGMN 5 $9.00 9 45.7 [1.80]
5.1 mm
DN-10PLUG 50 $80.00 DN-10PLUGMN 5 $10.00 10 50.8 [2.00]
[0.20 in]
DN-11PLUG 50 $77.00 DN-11PLUGMN 5 $11.00 11 55.9 [2.20]
11.0 mm
[0.43 in]
DN-DIS-BLADE
DN-DIS-BMN Disconnect Blade
Part Number Description Pcs/Pkg Price
19.2 mm 5.0 mm
[0.77 in] [0.20 in] DN-DIS-BLADE Terminal block disconnect blade for DN-FE2, 50 $21.50
DN-DIS-BMN DN-FE4, DN-DIS2 and DN-DIS4 10 $5.50
26.9 mm
[1.08 in]
DN-DIS-BLADE
End Brackets
Pcs/ Price/
Part Number Description
End Brackets Pkg Pkg
DN-EB15 100 $64.00
Terminal block end stop 7mm width screw clamping. Gray
DN-EB15MN 20 $14.00
DN-EB35 50 $39.50
Terminal block end stop 9mm width screw clamping. Gray
DN-EB35MN 20 $18.00
DN-EB35-A 50 $28.50
Terminal block end stop 6mm width screw clamping. Black
DN-EB35-A-10 10 $7.50
DN-QEB35 50 $25.50
Terminal block end stop 6mm width screwless clamping. Black
DN-QEB35-10 10 $7.50
16 mm
34.0 mm
[1.34 in]
[0.63 in]
7 mm
[0.28 in]
For more information on accessories, see the “DINnectors Accessories” section of this chapter.
Accessories
End Covers
Certain end covers can be used with multiple terminal block parts to cover and insulate the open
side, or to put more space between adjacent blocks.
Spacers
Spacers are used to put more space between adjacent blocks. Top Covers
DINnectors Spacers DINnectors Top Covers
For Use Pcs/ For Use Pcs/
Part Number Description Price Part Number Description Price
with Pkg with Pkg
DN-S1210 Spacer for DN-T12-A and DN-T10-A 100 $30.50 DN-C12 Top cover, clear, printed 100 $36.50
DN-T10-A series terminal DN-T12-A
DN-T12-A DN-C12MN electrical symbol. 25 $7.75
DN-S1210MN blocks 25 $9.25
DN-S86 Spacer for DN-T8 and DN-T8 100 $36.50 DN-C10 Top cover, clear, printed 100 $36.50
DN-T6 series terminal DN-T10-A
DN-T6 DN-C10MN electrical symbol. 25 $7.75
DN-S86MN blocks 25 $7.75
DN-C86 Top cover, clear, printed DN-T8 100 $36.50
DN-EMXM1SPA1 Spacer for single-level
plug-in terminal blocks
DN-EMXM1
DN-QEMXM1 25 $7.25 DN-C86MN electrical symbol. DN-T6 25 $7.75
Spacer for double-level DN-EMXDV DN-DC10 Top cover, clear, printed 100 $34.50
DN-EMXDVSPA1 25 $8.25 DN-D10
plug-in terminal blocks DN-QEMXDV DN-DC10MN electrical symbol. 25 $7.75
DN-FESPA Spacer for DN-FE sockets DN-FE 50 $15.00 DN-MC10 Top cover, clear, printed 100 $37.50
DN-M10
and DN-DIS disconnects DN-DIS DN-MC10MN electrical symbol. 25 $7.75
DN-FESPA-10 10 $3.00
Accessories
DINnector End Covers and Spacers Dimensions
Part Number Length Height Thickness
DN-EC1210 DN-EC1210MN 44mm [1.73 in] 35mm [1.38 in]
DN-S1210 DN-S1210MN 55mm [2.17 in] 44mm [1.73 in]
DN-EC86 DN-EC86MN 50mm [1.97 in] 43mm [1.69 in]
DN-S86 DN-S86MN 55mm [2.17 in] 49mm [1.93 in]
DN-EC4 DN-EC4MN 56mm [2.21 in] 48mm [1.89 in]
DN-EC1/0 DN-EC1/0MN 62mm [2.44 in] 60mm [2.36 in] 1.5 mm [0.06 in]
DN-DEC10 DN-DEC10MN 72mm [2.80 in] 55mm [2.17 in]
DN-EC14 – 78mm [3.08 in] 55mm [2.17 in]
DN-EC14S – 55mm [2.17 in] 50mm [1.97 in]
DN-ECM10 DN-ECM10MN 32mm [1.26 in] 27mm [1.06 in]
DN-ECKBD DN-ECKBDMN 52mm [2.05 in] 34.5 mm [1.36 in]
DN-EC1210, DN-EC1210MN DN-EC86,
DN-EMXM1EC1 DN-EMXM1EC2 DN-EC86MN DN-EC4 (MN),
DN-EMXDVEC1 DN-EMXDVEC2 DN-EC1/0 (MN), DN-ECKBD (MN),
DN-S1210, DN-S1210MN, DN-S86 (MN)
DN-EMXDVSPA1 DN-EMXM1SPA1 as shown on next page
DN-FESPA DN-FESPA-10
Part Number DN-FESEP-10
DN-FESEP Length Height Thickness
DN-EC1210
DN-QEC12 DN-QEC12MN 50mm [1.97 in] 23mm [0.9 in]
44 mm [1.73 in] 35 mm [1.38 in]
DN-EC1210MN
DN-QEC10 DN-QEC10MN 57.4 mm [2.26 in] 33.6 mm [1.32 in] H
1.5 mm [0.06 in]
DN-QEC8
DN-EC86 DN-QEC8MN 63mm [2.48 in] 38.5 mm [1.52 in]
50 mm [1.97 68.5
in] mm43[2.70
mm 1.5 mm [0.06 in]
DN-QEC12-1-2 – in] [1.69 in][1.12 in]
28.5 mm
DN-EC86MN
DN-QEC12-2-2 – 87.5 mm [3.44 in] 28.5 mm [1.12 in]
L T
DN-QDEC12 – 98mm [3.86 in] 37mm [1.46 in]
H H H
L T L T L T
L T
Accessories
Dimensional Drawings
DN-EMXM1EC1 DN-EMXM1EC2
1.5 mm
[0.06 in] 57.5 mm 1.5 mm
57.5 mm [2.26 in] [0.06 in]
[2.26 in]
28.5 mm
28.5 mm
[1.12 in]
[1.12 in]
DN-EMXDVSPA1
2.5 mm DN-EMXM1SPA1
75.6 mm
[2.98 in] [0.10 in]
57.5 mm 2.5 mm
[2.26 in] [0.10 in]
51.0 mm
[2.01 in]
28.5 mm
[1.12 in]
DN-EMXDVEC1 DN-EMXDVEC2
1.5 mm 75.6 mm 1.5 mm
75.6 mm [0.06 in] [2.98 in] [0.06 in]
[2.98 in]
51.0 mm
[2.01 in]
51.0 mm
[2.01 in]
DN-FESEP,
DN-FESEP-10 DN-FESPA, DN-FESPA-10
1.0 mm 1.5 mm
55.0 mm 55.0 mm
[0.04 in] [0.06 in]
[2.17 in] [2.17 in]
33.0 mm
33.0 mm
[1.30 in]
[1.30 in]
Accessories
DN-LB (blank)
shown on right
DN-L
• Fits terminal block types: All except DN-LAB (blank) shown on left; DN-LTA marker shown top; DN-LT60 marker
Screwless DINnectors , DN-T12-A, shown middle;
DN-M10-A, DN-MG, and DN-TL series part of DN-LA100 on right
DN-LTGND shown bottom
• Material: Thermoplastic with heat DN-LA
embossed black print
• Fits terminal block types: DN-T12-A
DN-LT
Note: • Fits terminal block types: All except
1. The marking sequence of 50 tags (i.e. 101-150) is series
Screwless DINnectors
printed 10 times in each package of 500 tags. • Material: Thermoplastic with heat (see DN-QL series)
2. The DN-L tags fit all DINnectors 6mm wide and embossed black print
wider. Note:
•M aterial: Thermoplastic with heat
3. The DN-L tags 1. T he marking sequence (i.e. 1-100) is printed five
embossed black print
fit all DIN- Dimensions Note:
times in each package of 500 tags.
nectors 6mm 12 mm 6 mm
2. T he DN-T12-A series is 5mm wide, so the 6mm 1. T hese marking tags allow the
wide and wider [0.47 in] [0.23 in]
wide DN-L tags do not fit these blocks. flexibility of creating custom Dimensions
but will leave a 3. T he DN-LA tags fit marking sequences on site. 5 mm 3 mm
[0.19 in] [0.11 in]
gap between tags all DINnectors 5mm Dimensions 2. T he DN-M10-A support a
on blocks wider wide and wider but 12 mm 5 mm maximum of three digits (tags),
than 6mm. will leave a gap [0.47 in] [0.19 in] while other DINnectors support
between tags on up to four digits (tags)
Marking Pcs/ Price
Part# blocks wider than
Sequence Pkg 5mm. Marking Pcs/
DN-L50 Part# Price
1-50 500 $32.50 Sequence Pkg
51-100 DN-L100 500 $32.50 Marking Pcs/ Price 1-5 DN-LT15 100 $5.75
Part#
101-150 DN-L150 500 $32.50 Sequence Pkg 6-0 DN-LT60 100 $5.75
1-100 DN-LA100 500 $32.50 1 DN-LT1 100 $5.75
151-200 DN-L200 500 $32.50 101-200 DN-LA200 500 $32.50 2 DN-LT2 100 $5.75
201-250 DN-L250 500 $32.50 201-300 DN-LA300 500 $32.50 3 DN-LT3 100 $5.75
251-300 DN-L300 500 $32.50 301-400 DN-LA400 500 $32.50 4 DN-LT4 100 $5.75
301-350 DN-L350 500 $32.50 Blank Tags DN-LAB 500 $32.50 5 DN-LT5 100 $5.75
L1, L2, L3, L, 6 DN-LT6 100 $5.75
351-400 DN-L400 500 $32.50 7 DN-LT7 100 $5.75
N, GND, +, -, DN-LAS 500 $32.50
401-450 DN-L450 500 $32.50 COM,COM* 8 DN-LT8 100 $5.75
Blank DN-LB 500 $22.00 9 DN-LT9 100 $5.75
0 DN-LT0 100 $5.75
L1, L2, L3, L, N, GND,
+, -, COM,COM* DN-LS 500 $32.50 DN-LAT-A Unprinted DN-LTBLNK 100 $5.75
• Fits terminal block types: Triple level A DN-LTA 100 $5.75
DN-QL DN-TL14 B DN-LTB 100 $5.75
Material: Thermoplastic with heat C DN-LTC 100 $5.75
• Fits terminal block types: Screwless
DN-Q series embossed black print D DN-LTD 100 $5.75
Dimensions E DN-LTE 100 $5.75
• Material: Thermoplastic with heat em- Note: 5mm 6mm F DN-LTF 100 $5.75
bossed black print. Packaged 100 labels 1. T he marking sequence (i.e. [0.19 in] [0.23 in] G DN-LTG 100 $5.75
per card, and five cards per box. 1-100) is printed five times in H DN-LTH 100 $5.75
Note: each package of 500 tags. I DN-LTI 100 $5.75
1. The marking sequence (i.e. 1-100) J DN-LTJ 100 $5.75
is printed five times in each K DN-LTK 100 $5.75
package of 500 tags. Dimensions Marking Pcs/ Price
Part # L DN-LTL 100 $5.75
Sequence Pkg M DN-LTM 100 $5.75
1-100 DN-LAT100-A 500 $29.00 N DN-LTN 100 $5.75
101-200 DN-LAT200-A 500 $29.00 – – – –
201-300 DN-LAT300-A 500 $29.00 P DN-LTP 100 $5.75
301-400 DN-LAT400-A 500 $29.00 Q DN-LTQ 100 $5.75
401-500 DN-LAT500-A 500 $29.00 R DN-LTR 100 $5.75
501-600 DN-LAT600-A 500 $29.00 S DN-LTS 100 $5.75
DN-QLS Shown Blank Tags DN-LATB-A 500 $21.00 T DN-LTT 100 $5.75
L1, L2, L3, L, N, U DN-LTU 100 $5.75
+,-, COM,COM* DN-LATS-A 500 $29.00
V DN-LTV 100 $5.75
Marking Sequence Part # Pcs/
Pkg Price
W DN-LTW 100 $5.75
X DN-LTX 100 $5.75
1-100 DN-QL100 500 $25.50
Y DN-LTY 100 $5.75
101-200 DN-QL200 500 $25.50
Z DN-LTZ 100 $5.75
201-300 DN-QL300 500 $25.50
301.400 DN-QL400 500 $25.50 DN-LTGND 100 $5.75
401-500 DN-QL500 500 $25.50 + DN-LTPOS 100 $5.75
Blank Tags DN-QLB 500 $21.50 - DN-LTNEG 100 $5.75
L1, L2, L3, L, N, +,-, ~ DN-LTAC 100 $5.75
COM,COM* DN-QLS 500 $29.00 = DN-LTDC 100 $5.75
Accessories
Terminal Marking Accessories
Price
Part # Description For Use With Pcs/Pkg Each
DN-EMLBL1 Blank labels
DN-EMPEG1 pin protectors for
100 $5.25
DN-EMLBL2 Labels printed 1 – 12 DN-xEMXxx plug-in terminal 100 $7.25
blocks
DN-EMLBL3 Labels printed 13 – 24 100 $7.25
DN-MTA dimensions
Price
Part# Description Pcs/Pkg Each
20.5 mm 5.9 mm
Marking tag adapter
[0.81 in] [0.23 in] DN-MTA holds up to six 50 $8.00
DN-LT tags
3 mm
[0.12 in]
DN-MTA marking tag adapter
Marking pen
BM-M092CS BM-M093CS
6 mm 10 mm
8 mm 2.6 mm [0.24 in] 3.3 mm [0.39 in]
10 mm
[0.31 in] [0.1 in] [0.39 in] [0.13 in]
BM-M094CS
10 mm
12 mm 3.15 mm [0.39 in]
[0.47 in] [0.12 in] Wire protectors are metallic strips that
physically isolate the conductor from the
terminal screw. The protectors prevent
12.2 mm 20.7 mm cutting or nicking softer conductors.
[0.48 in] [0.81 in]
23 mm 7.3 mm
[0.91 in] [0.29 in]
4.2 mm 4.7 mm 139.3 mm
Ø [5.48 in]
[0.17 in] [0.19 in]
Finger-safe EPDB301 310 max 1 pole distribution block, 1 in/1 out 200 kA 1 8.1 oz. $25.00
(EPDB) EPDB306 380 max 1 pole distribution block, 1 in/6 out 200 kA 1 9.1 oz. $35.50
1 pole distribution block,
EPDB512 570 max 2 in/12 out 200 kA 1 12.5 oz. $41.00
EPDB702 760 max 1 pole distribution block, 2 in/2 out 200 kA 1 16.4 oz. $64.00
Accessory DN-EB35* – End bracket – 50 1.87 lb. $39.50
*Note: DIN-rail anchors are required on block or blocks. Anchors must be used to
prevent damage to the plastic housing when tightening terminals.
EPDB101 EPDB104
EPDB301 EPDB306
EPDB702
EPDB512
Part Number Minimum Enclosure Size in(mm)* Wire Connector Hole Diameter
EPDB101 16 x 16 x 6.75 [406.4 x 406.4 x 171.45] Part Number Line in (mm) Load in (mm)
EPDB104 16 x 16 x 6.75 [406.4 x 406.4 x 171.45] EPDB101 0.450 [11.43] 0.450 [11.43]
EPDB301 36 x 30 x 12.63 [914.4 x 762 x 320.80 EPDB104 0.450 [11.43] 0.246 [6.25]
EPDB306 24 x 20 x 6.75 [609.6 x 508 x 171.45] EPDB301 0.720 [18.29] 0.720 [18.29]
EPDB512 24 x 20 x 6.75 [609.6 x 508 x 171.45] EPDB306 0.870 [22.10] 0.314 [7.98]
EPDB702 36 x 30 x 12.63 [914.4 x 762 x 320.80] EPDB512 0.687 [17.45] 0.265 [6.73]
*Note: Terminal block SCCR determined based on testing in minimum-size enclosure EPDB702 0.875 [22.23] 0.875 [22.23]
4 to 14 AWG
25 to 2.5mm² Yes Yes
2/0 to 8 AWG 0.550 [14.0] top row,
EPDB104 0.750 [19.0] 70 to 10mm² Yes Yes 0.850 [21.6] bottom row screws fully opened N/A Yes
no wire in hole No N/A
350 Kcmil to 2/0 AWG 350 Kcmil to 2/0 AWG
Yes Yes Yes Yes
185 to 70mm² 185 to 70mm²
EPDB301 1.350 [34.3] 1.250 [31.8]
1/0 to 6 AWG 1/0 to 6 AWG
No Yes No Yes
50 to 16mm² 50 to16mm²
500 to 250 Kcmil 2 to 14 AWG
Yes Yes Yes Yes
240 to 150mm² 35 to 2.5mm²
0.590 [15.0] top row,
EPDB306 1.250 [31.8] 4/0 to 6 AWG No Yes 1.200 [30.5] bottom row screws fully opened N/A Yes
120 to 16mm²
N/A N/A N/A no wire in hole No N/A
300 Kcmil to 4/0 AWG Yes Yes
150 to 120mm² 4 to 14 AWG
0.550 [14.0] top row Yes Yes
1.15 [29.2] top row, 3/0 to 4 AWG 25 to 2.5mm²
EPDB512 1.400 [35.6] bottom row 95 to 25mm² No Yes 1.00 [25.4] middle row
1.220 [31.0] bottom row
screws fully opened N/A No screws fully opened N/A Yes
no wire in hole No N/A no wire in hole Yes N/A
EPDB702 1.250 [31.8] 300 Kcmil to 6 AWG 1.250 [31.8] 300 Kcmil to 6 AWG
No Yes No Yes
150 to 16mm² 150 to 16mm²
screws fully opened N/A No screws fully opened N/A No
no wire in hole No N/A no wire in hole No N/A
Table A Table B
Block Cover Block Cover
HPB1XX-(pole) PBC21 HPB106-1 PBC31
HPB3XX-(pole) PBC31 HPB106-2 PBC32
HPB312-3
HPB106-3 PBC33
Load Side
Load Side
Load Side
PBC71 Power distribution block cover for all 760A open style 1-pole and 3-pole blocks. 1 pole block
requires 1 cover. 3-pole block requires 3 covers 1 0.9 oz. $6.25
PB7121, PB7123
Covers
Optional Cover for Optional Cover for
PB1011, PB1012, PB1013 PB3061, PB3062, PB3063 PB4011, PB4012, PB4013
PB1041, PB1042, PB1043 PB3121, PB3122, PB3123 PB5121, PB5122, 5123
Part A Dimension
Number in[mm] Part A Dimension
PBC21 0.94 [23.88] Number in[mm]
PBC22 1.75 [44.45] PBC31 2.10 [53.34]
PBC23 2.56 [65.02] PBC32 3.72 [94.49]
PBC33 5.34 [135.64]
Optional Cover for PB7121 and PB7123 Note: Dimensions are in inches [milimeters]
Part
Number
PBC71
Wiring Accessories
Single Insulated Wire Ferrules
These tin-plated copper single insulated ferrules
are designed to accommodate conductors with
cross-sections ranging from 20AWG to 1AWG
(0.5 to 50 mm²). Tolerances according to DIN
46228 part 4.
Wiring Accessories
Crimp Terminals
Partially insulated crimp terminals are constructed from high quality tin-plated
copper and PVC. Heat resistant from -4°F [-20°C] up to +167°F [+75°C].
Flammability classification UL 94-V0.
Ring Terminals
Partially Insulated PVC Ring Terminals
Cross Section Dimension (mm) Pcs/
Part Number Price
AWG mm² X Y Z Pkg
V70RK004004 20 - 18 0.5 - 1 4.0 8.0 22.2 100 $7.50
V70RK004005 20 - 18 0.5 - 1 5.0 8.0 22.2 100 $7.50
V70RK004011 16 - 14 1.5 - 2.5 4.0 8.6 23.0 100 $8.00
V70RK004012 16 - 14 1.5 - 2.5 5.0 8.6 23.0 100 $8.50
V70RK004017 12 - 10 4-6 4.0 9.5 26.9 100 $12.00
V70RK004018 12 - 10 4-6 5.0 9.5 26.9 100 $12.00
Fork Terminals
Partially Insulated PVC Fork Terminals
Cross Section Dimension (mm) Pcs/
Part Number Price
AWG mm² X Y Z Pkg
V70GK004003 20 - 18 0.5 - 1 4.0 7.3 22.3 100 $7.50
V70GK004004 20 - 18 0.5 - 1 5.0 8.0 21.7 100 $8.00
V70GK004008 16 - 14 1.5 - 2.5 4.0 7.3 22.3 100 $7.50
V70GK004009 16 - 14 1.5 - 2.5 5.0 8.1 22.3 100 $8.50
V70GK004011 12 - 10 4-6 4.0 9.1 25.8 100 $11.50
V70GK004012 12 - 10 4-6 5.0 9.1 25.8 100 $11.50
Butt Connectors
Fully Insulated PVC Butt Connectors
Cross Section Dimension (mm) Pcs/
Part Number Price
AWG mm² X Y Pkg
V70SV004001 20 - 18 0.5 - 1 5.4 26.0 100 $8.00
V70SV004002 16 - 14 1.5 - 2.5 6.1 26.0 100 $9.00
V70SV004003 12 - 10 4 - 6 8.0 26.0 100 $12.50
Pin Terminals
Partially Insulated PVC Pin Terminals
Cross Section Dimension (mm) Pcs/
Part Number Price
AWG mm² X Y Pkg
V70SS004001 20 - 18 0.5 - 1 12.0 23.3 100 $8.50
V70SS004002 16 - 14 1.5 - 2.5 12.0 23.4 100 $9.00
V70SS004003 12 - 10 4 - 6 14.0 28.2 100 $13.50
Note: Dimensions are approximate. Please visit our website www.AutomationDirect.com for complete engineering drawings.
Wiring Accessories
Disconnect Terminals
Disconnect terminals are constructed from copper-enhanced PVC and brass. Heat re-
sistant from -4°F [-20°C] up to +167°F [+75°C]. Flammability classification UL 94-V0.
Note: Dimensions are approximate. Please visit our website www.AutomationDirect.com for complete engineering drawings.
Wiring Accessories
Disconnect Terminals
Disconnect terminals are constructed from copper-enhanced PVC and brass. Heat
resistant from -4°F [-20°C] up to +167°F [+75°C]. Flammability classification UL
94-V0.
2011/65/EU
Note: Dimensions are approximate. Please visit our website www.AutomationDirect.com for complete engineering drawings.
Wiring Accessories
Crimping Tools
Crimping Tools
Part Number Description Weight Price K70ZA000113
Crimping tool for use with single ferrules AWG 20 - 10 (0.5 - 6 mm²) and twin ferrules
0.74 lb
K70ZA000113 AWG 2 x 18 - 2 x 12 (2 x 0.75 - 2 x 4 mm²). 5 crimping positions. With and without
(335g)
$99.00
insulating collar. Conforms to DIN 46228 part 1 and 2.
Crimping tool for use with single ferrules AWG 10 - 4 (6 - 25 mm²) and twin ferrules 1.19 lb
K70ZA000117 AWG 2 x 12 - 2 x 8 (2 x 4 - 2 x 10 mm²). 4 crimping positions. Conforms to DIN (540g) $105.00
46228 part 1 and 4.
K70ZA000118 Crimping tool for use with single ferrules AWG 2 - 1 (35 - 50 mm²) and twin ferrules
AWG 2 x 6 (2 x 16 mm²). 2 crimping positions. Conforms to DIN 46228 part 1 and 4.
1.19 lb
(540g)
$105.00
K70ZA000130 Crimping
positions.
tool for PVC-insulated terminals AWG 20 - 10 (0.5 - 6 mm²). 3 crimping 1.12 lb
(510g)
$99.00
Note: Z&F crimping tools recommended by the ferrule manufacturer before terminating in terminal blocks,
wire connectors, or end-product terminals (such as starters, etc.).
V30AE000053 V30AE000053
V30AE000055 V30AE000055
V30AE000056 V30AE000056
V30AE000025 V30AE000058
V30AE000026 V30AE000059
V30AE000027 V30AE000060
V30AE000028 V30AE000061
V30AE000029 V30AE000062
V30AE000030 V30AE000063
V30AE000031 V30AE000064
V30AE000033 V30AE000067
V30AE000035 V30AE000070
V30AE001134 V30AE001145
V30AE000606 V30AE000607
V30AE000733 V30AE000734
V30AE000608 V30AE000609
V30AE000735 V30AE000736
Twin Ferrules
V30AE000623 V30AE000625
V30AE000737 V30AE000738
V30AE000611 V30AE000611
V30AE000748 V30AE000748
V30AE001148 V30AE001148
V30AE001139 V30AE001150
V30AE001141 V30AE001152
V30AE001143 V30AE001154
BM-5345
Crimping tool and die set
Fig. 1 (BM-537)
Fig. 2 (BM-539)
End Sleeve Terminals 22-12
End Sleeve Terminals 10-6 Fig. 3 (BM-535)
AWG (0.5-4 mm²)
AWG (6-16mm²) Uninsulated Copper Terminals
20-8 AWG (0.5-10 mm²)
DN-CT-HDL Crimping tool handle for DN-CT-Dx dies (dies NOT included)
Approximate dimensions: 9.75 x 2.52 x 0.95 in (234 x 64 x 24 mm); 16.2 oz (460g) 1 $52.00
DN-CT-D2 Die set for DN-CT-HDL; 22-14 AWG (0.5-2.5 mm2) red & blue insulated terminals 1 $42.00 DN-CT-HDL Crimping Tool
DN-CT-D3 Die set for DN-CT-HDL; 22-10 AWG (0.5-6 mm2) non-insulated terminals 1 $36.50
DN-CT-D4 Die set for DN-CT-HDL; 24-8 AWG (0.25-10 mm2) wire ferrules 1 $36.50
DN-CT-D5 Die set for DN-CT-HDL; 6-4 AWG (16-25 mm2) wire ferrules 1 $36.50
DN-CT-D6 Die set for DN-CT-HDL; 2-1/0 AWG (35-50 mm ) wire ferrules
2
1 $36.50
DN-CT-D7 Die set for DN-CT-HDL; 22-10 AWG (0.5-6 mm2) open barrel non-insulated terminals 1 $55.00
DN-CT-D8 Die set for DN-CT-HDL; 8-pin (RJ45) modular plugs 1 $36.50
DN-CT-D9 Die set for DN-CT-HDL; 6-pin (RJ11/RJ12) modular plugs 1 $36.50
Crimping tool modular system; includes handle and three die sets
(DN-CT-HDL + DN-CT-D2 + DN-CT-D4 + DN-CT-D5)
DN-CT-SET The die pairs are held together for easy handling, and interchange without separate 1 $147.00
tools. DN-CT-SET
* The DN-CT-xx series features a crimping tool with multiple interchangeable dies separately available. Crimping Tool & Die Set
The die pairs are held together for easy handling, and can be interchanged without separate tools.
The finished square and hexagonal crimps have the same cross-sectional area.
Choosing between the square and hexagonal crimp tools depends on the shape of
the hole where the wire will be inserted. Square crimps fit better in rectangular holes
while hexagonal crimps fit better in round holes.
Wiring Accessories –
Cutting & Stripping Tools
Wire Cutting and Stripping Tools
Wire Cutting and Stripping Tools
Pcs Price
Part # Description /Pkg Each
Self-Adjusting Cutting and Stripping Tool
Cutting and stripping tool with replaceable blades and jaw inserts; includes (1) DN-WSJ blade
DN-WS Approximate dimensions: 7.5 x 4.8 x0.8 in (191 x 123 x 20 mm); Weight: 4.8 oz (136g) 1 $79.00
DN-WSJ DN-WS replacement straight-blade insert; for PVC insulations; 34-8 AWG (0.02-10 mm2) 1 $34.00
DN-WSMMC DN-WS 16 mm2 blade insert; 12-5 AWG (4-16 mm2) 1 $39.50
DN-WSVBC DN-WS V-blade insert; for harder insulations such as PTFE & PVC; 28-12 AWG (0.1-4 mm2) 1 $24.50
DN-WSRJ DN-WS replacement jaw inserts 2 $6.25
Cable Stripping Tool
Cable stripping tool; cable diameters 0.1-0.43 in (2.5-11 mm) with insulation up to 0.04 in (1.0 mm) thick
DN-CST Approximate dimensions: 3.6 x 1.6 x 0.8 in (90.5 x 39.5 x 19 mm); Weight: 0.9 oz (28g)
1 $24.00