Beruflich Dokumente
Kultur Dokumente
TABLE OF CONTENTS
TITLE PAGE
Abstract i
List of symbols iv
List of figures v
List of tables vi
List of Graphs vii
1 Introduction
1.1 Brief review of ADP - 1 1
1.2 Structural Design - Overview 2
2 V-n diagram 4
3 Structural Design of wing
3.1 Introduction 10
3.2 Air –Inertia Load Estimation 11
3.3 Shear force & Bending moment Distribution 13
3.4 Material Selection 14
3.5 Wing Spar and Stringer Design 18
3.6 Shear flow Distribution 33
4 Structural Design of Fuselage
7 Conclusion 57
Bibliography 58
Website reference 59
Page |7
LIST OF SYMBOLS
LIST OF FIGURES
LIST OF TABLES
LIST OF GRAPHS
1
INTRODUCTION
Aircraft Design Project-II deals with a more in-depth study and analysis of aircraft performance
and structural characteristics. In the following pages we have carried out structural analysis of fuselage
and wings and the appropriate materials have been chosen to give our aircraft adequate structural
integrity. The flight envelope of our aircraft has also been established by constructing the V-n diagram.
We have also determined the landing gear position, retraction and other accompanying systems and
mechanisms. The study of all the above mentioned characteristics, has given us insight into the
complexity of designing a subsonic multi-role 8 seater business jet.
5. Height 4.8 m
P a g e | 12
The structure of an aircraft is required to support two classes of loads, first termed ground
loads, includes all loads encountered by the aircraft during movement or transportation on the
ground such as taxing, landing loads, towing etc, while the second is the air loads, comprises
loads imposed on the structure. The two classes of loads of loads may be still classified as
surface forces acting on the surface of the structure and body forces acting over the volume of
the structure. Basically all air loads are the resultant of the pressure distribution over the surfaces
of the skin produced by steady flight, maneuver or gust conditions. Generally these causes
bending, shear, torsion in all parts of the structure in addition to local normal pressure loads
imposed on the skin.
Ground loads encountered in landing and taxing subject the aircraft to concentrated shock
loads through the undercarriage system. The majority of the aircraft have their main
undercarriage located in the wings with nose wheel or tail wheel in the vertical plane of
symmetry. Clearly the position of the undercarriage should be in such a position so as to produce
minimum loads on the wing structure.
P a g e | 14
2
ESTIMATION OF V-N DIAGRAM
The control of weight in aircraft design is of extreme importance. Increase in weight
requires stronger structures to support them, which in turn lead to further increase in weight & so
on. Excess of structural weight means lesser amounts of payload, affecting the economic
viability of the aircraft.
Therefore there is need to reduce aircraft’s weight to the minimum compatible with
safety. Thus to ensure general minimum standards of strength & safety, airworthiness regulations
lay down several factors which the primary structures of the aircraft must satisfy.
These are
1. LIMIT LOAD: the maximum load that the aircraft is expected to experience in normal
operation.
2. PROOF LOAD: product of the limit load and proof factor(1.0-1.25)
3. ULTIMATE LOAD : product of limit load and ultimate factor(1.0-1.5)
The aircraft’s structure must withstand the proof load without detrimental distortion &
should not fail until the ultimate load has been achieved.
V-n Diagram:
A chart of Velocity versus load factor (V-n diagram) is another way of showing limits of
aircraft performance. It shows how much load factor can be safely achieved at different
airspeeds.
P a g e | 15
The maneuverability of the aircraft is also dictated by the loads falling on the structures
during the maneuvers. Both the aerodynamic and structural limitations for a given airplane are
illustrated in the V-n diagram, a plot of load factor versus flight velocity.
A V-n diagram is type of flight envelope for the aircraft establishing the maneuver boundaries.
The BCAR (British civil airworthiness requirements) has given the basic strength and
flight performance limits of various categories of the aircraft. They are listed below
Fully aerobatic 6 -3
Tabular column 2: LOAD FACTOR
The 8 seater executive aircraft comes under the normal category. Therefore the load
factor limits for the aircraft is 3.8 & -1.5.
The V-n diagram for the aircraft is drawn for the two cases namely,
1. Intentional maneuver( pilot induced maneuver )
2. Unintentional maneuver( gusts)
INTENTIONAL MANEUVER:
Intentional maneuvers are induced by the pilot during climb, pull up or pull down,
banking the plane etc...
The load factor is function of velocity. The expression relating the load factor and the
velocity is given by
nmax =
Where nmax is the maximum load factor, V is the speed of the aircraft, Vs is the stalling
speed of the aircraft.
The stalling speed of the aircraft Vs 2 =
Nmax= V Nmax=
V
3.5 110.74
-0.75 51.256
3 102.53
-1 59.197
2.5 93.599
2 83.71
1.5 72.501
Tab3. Velocity VS Load Factor
1 59.197
The dive speed of the aircraft is the maximum speed of the aircraft. The dive speed is equal to
the sum of the cruising speed and 60 knots.
VD = 236.11 + 60 knots
= 266.67 m/s
GUSTS:
These may be critical for large, high speed aircraft and may possibly cause higher
loads than control initiated maneuvers.
Thus in the gust analysis, the change in load factor due to the gust is calculated. The
BCAR has given standard gust velocities for stall, cruise, dive speeds as 66, 50, 25 ft/s
P a g e | 17
respectively. The small change in load factor ∆n due to the gust is calculated by assuming a
sharp gust.
The change in load factor ∆n =
In the above formula, gusts are assumed to be sharp but it is usually graded, hence
a relief factor called gust alleviation factor K is introduced in the term.
!"
Where K = , µ =#$%$&$%
'(
Where ρ is the density, C is the mean aerodynamic chord, g is the acceleration due to gravity;
CLα is the slope lift coefficient.
µ =
$
$)$
*
$+,+
µ=
,$-.$.+$.$+
µ = 50.36
K=
$/
=
/
Κ = 0.796
P a g e | 18
123
#
K = Therefore ∆n = 0
!"
#
123
∆n = 0
!"
+-/$,$.$+$$-.-+
=
$+,+
∆n = 1.062
#
123
∆n = 0
!"
+-/$,$.$+$.$/..
=
$+,+
∆n = 2.725
For DIVE SPEED V= 266.67 m/s, U= 7.5 m/s
#
123
∆n = 0
!"
+-/$,$.$+$+$///+
=
$+,+
∆n
∆ = 1.794
P a g e | 19
V 1+∆
∆n 1-∆
∆n
3
STRUCTURAL ANALYSIS AND DESIGN OF WINGS
1. Distributed loads - Loads such as aerodynamic loads, weight of the wing and weight of
fuel.
2. Concentrated loads – Loads such as thrust, engine weight, landing gear weight and
armament weight.
SCHRENK’S CURVE:
Lift is a component of the resultant aerodynamic force acting at the centre of pressure of
an aerodynamic chord, along a direction perpendicular to the direction of the relative wind. At a
particular altitude and at a specific angle of attack, Lift varies along the wing span due to the
variation in chord length along the span. Schrenks curve defines this lift distribution over the
wing span of an aircraft. Since the wings of an aircraft are symmetrical about the longitudinal
axis, the Schrenks curve for the starboard wing alone can be obtained at first. This is given by
45 4
y=
TO FIND y1:
Lift force is found along the line joining the aerodynamic centers of chords along the
wing span. Hence, the wing is rotated about the wing root so that the line joining the
aerodynamic centers becomes the horizontal line.
6
a= )
789:
.,
a= )
789..; .<
=6.55
Lift per unit length at wing root = CL×0.5×ρ×V2×CR
= 0.23884×0.5×1.4×236.1112×2.55
= 23766.98 N/m
6.55 m
X Y1
0 23766.98
1 22571.7
2 21376.42
3 20181.14
4 18985.86
5 17790.58
6 16595.3
6.55 15937.89
Tab5. Span VS Linear Lift Distribution
25000
LINEAR LIFT DISTRIBUTION
20000
15000
Series1
10000
Series2
5000
0
0 1 2 3 4 5 6 6.55
SPAN (a)
15138.35 N/m
6.55 m
Fig 5. Elliptic Lift Distribution
Y2 = 1155.60@A BCD E F
x Y2
0 15138.317
1 14960.852
2 14415.354
3 13457.142
4 11987.651
5 9779.05
6 6072.292
6.55 0
55BGHBIDJKKBH55GGKCLABCDMF
Y1+Y2 =
x Y1+Y2
0 19452.65
1 18766.28
2 17895.89
3 16819.14
4 15486.76
5 13784.82
6 11333.796
6.55 7968.95
Tab 7:SpanVsSchrenk's value
P a g e | 25
x y
0 -12464.07
1 -8948.74
2 -6014.49
3 -3661.28
4 -1889.11
5 -697.97
6 87.88
6.55 0
Tab 8: SpanVs Load acting on wing
Power Plant:
According to our design data, Our Aircraft power plant is attach to rear fuselage. So,
power plant calculation won’t be calculated.
Wf = 23215.55
Consider as equation,
yf = 1902.91x-12464.07
2 -8658.25
3 -6755.35
4 -4852.43
5 -2949.52
The solution methods which follow Euler's beam bending theory (σ/y=M/I=E/R) use the
bending moment values to determine the stresses developed at a particular section of the beam
due to the combination of aerodynamic and structural loads in the transverse direction. Most
engineering solution methods for structural mechanics problems (both exact and approximate
methods) use the shear force and bending moment equations to determine the deflection and
slope at a particular section of the beam. Therefore, these equations are to be obtained as
analytical expressions in terms of span wise location. The bending moment produced here is
about the longitudinal (x) axis.
As both the wings are symmetric, let us consider the starboard wing at first. There are
three primary loads acting on a wing structure in transverse direction which can cause
considerable shear forces and bending moments on it. They are as follows:
1 Y1 155673.719 5.458
2 Y2 77896.859 2.781
∑V=0
77836.859-54426.46-23215.55-VA = 0
VA = 194.85
∑MA = 0
MA+ (54426.465×1.637)+(23215.55×1.31)-(155673.719×5.458)-(77836.859×2.781)
MA – 946622.97 = 0
MA= 946622.97
P a g e | 30
SHEAR FORCE
S.F1 = -298.84 x2 + 45489.019 x + 577.8 @A BCD E S - 42.903 Sin-
F FD
T
1
U -290.52 T V A BCF V K GGF U -194.85
KGG D
0 -19625.79
1 -8113.17
2 1496.55
3 9203.37
4 15007.29
5 18908.31
6 20906.43
6.55 21194.28
Tab 10: Span VS Shear Force
BENDING MOMENT:
F
B.M = -199.21 x3 + 15163.006 x2 + 288.9 [x (x@A BCD E S ) + 42.903 Sin -1KGG] + 385.2
FA
(42.903- x2)1.5-290.52 (5+ 21.45 x2- 2.18 x3) + 94662.97
P a g e | 31
0 754870.44
1 1043525.353
2 1062831.914
3 1084364.515
4 1108829.591
5 1318721.935
6 1381469.212
6.55 943585.515
1600000
1400000 BENDING
MOMENT
1200000
1000000
800000
600000
400000
200000 SHEAR FORCE
0
-8 -6 -4 -2 0 2 4 6 8
WING SPAN
Shear force and bending moment diagrams due to loads along chordwise
direction at cruise condition:
Aerodynamic center- This is a point on the chord of an airfoil section where the bending
moment due to the components of resultant aerodynamic force (Lift and Drag) is constant
irrespective of the angle of attack. Hence the forces are transferred to this point for obtaining
constant Ma.c
Shear center- This is a point on the airfoil section where if a force acts, it produces only bending
and no twisting. Hence the force is transferred to this point and the torque is found.
Cn = CL cos ά + CD sin ά
= 1.398
CC = CL sin ά + CD cos ά
= 0.026
For Linear,
y = 23.05 x + 145.39 à1
Shear Force:
Integrate Eqn. 1
5HA
NC W 55 GGFD V 5AG DBF
P a g e | 33
0 0
1 156.915
2 336.88
3 539.895
4 765.96
5 1015.07
6 1287.24
7 1582.45
8 1900.72
9 2242.03
10 2606.40
11 2993.81
12 3404.28
12.84 3766.88
Tab 12: Span wise VS Shear Force
BENDING MOMENT:
.,
X W3.841 x3+72.69x2
0 0
1 76.531
2 176.108
3 321.77
P a g e | 34
vigneshaeronautical@gmail.com
4 536.584
5 843.575
6 1265.796
7 1826.293
8 2548.112
9 3454.299
10 4567.9
11 5911.961
12 7509.528
12.84 9064.425
Tab 13: Span wise VS Bending Moment
14000
BENDING MOMENT & SHEAR FORCE
12000 BENDING
MOMENT
10000
8000
6000 SHEAR
FORCE
4000
2000
CHORDWISE
Aerodynamic center- This is a point on the chord of an airfoil section where the bending
moment due to the components of resultant aerodynamic force (Lift and Drag) is constant
irrespective of the angle of attack. Hence the forces are transferred to this point for obtaining
constant Ma.c
Shear center- This is a point on the airfoil section where if a force acts, it produces only bending
and no twisting. Hence the force is transferred to this point and the torque is found
The lift and drag forces produce a moment on the surface of cross-section of the wing,
otherwise called a torque, about the shear center. Moment about the aerodynamic center gets
transferred to the shear center. The shear center on the chord under which it is locates.
T= ½ Cn ρ V2 c × 0.034 C
P a g e | 36
= 1325.51 C2
Where,
C à chord
the equation for chord can also be represented in terms of x by taking C = mx +k,
C = 0.264 x +2.55
0 0
1 9541.54
2 21052.24
3 34716.62
4 50719.18
5 69244.42
6 90476.85
7 114600.98
8 141801.31
9 172262.34
10 206168.6
11 243704.57
12 285054.76
12.84 322871.54
P a g e | 37
T2 = 0
T3 = -3347.9 ×C2
0 0
1 -24099.51
2 -53172.67
3 -87685.49
4 -128104.0
5 -174894.22
6 -228522.19
7 -289453.92
8 -358155.45
9 -435092.80
10 -520732.01
11 -615539.06
12 -719980.03
12.84 -815496.45
P a g e | 38
NET TORQUE:
Then the different torque components are brought together in a same graph to make a
comparison
The net torque will be sum of all the above torques (i.e.) torques due to normal force, chordwise
force, powerplant and aerodynamic moment.
400000
200000
0
1 2 3 4 5 6 7 8 9 10 11 12 13 14
-200000 Series1
Series2
-400000 Series3
-600000
-800000
-1000000
The specified structural roles of the wing (or main plane) are:
Ø To transmit: wing lift to the root via the main span wise beam
Inertia loads from the power plants, undercarriage, etc., to the main beam.
Aerodynamic loads generated on the aerofoil, control surfaces & flaps to the main
beam.
Ø To react against:
Landing loads at attachment points
Loads from pylons/stores
Wing drag and thrust loads
Ø To provide:
Fuel tank age space
Torsional rigidity to satisfy stiffness and aero-elastic requirements.
Ø To fulfill these specific roles, a wing layout will conventionally compromise:
Span wise members (known as spars or booms)
Chord wise members(ribs)
A covering skin
Stringers
P a g e | 40
The structural functions of each of these types of members may be considered independently as:
SPARS
v Webs – resist shear and torsional loads and help to stabilize the skin.
v Flanges - resist the compressive loads caused by wing bending.
SKIN
v Increase skin panel buckling strength by dividing into smaller length sections.
v React axial bending loads
RIBS
The maximum bending moment from previous section was found to be as 2897784.51
Nm. Therefore we define 3 Spars with front spar at 15% of chord, middle spar at 45% of chord
and rear spar at 70% of chord. The position of the three spars from the leading edge of the root
chord is given below as follows:
P a g e | 41
= 16517371.71Nm
The Structural load bearing members in the wing are the Spars and Stringers. The
bending moment carried by the Spars is 70% and that of Stringers is 30% of the total Bending
Moment.
A. Centroid
B. Moment of Inertia
C. Bending Moment
D. Bending Stress
P a g e | 42
FRONT SPAR:
I xx = 49789.88 cm4
I yy = 3292.22 cm4
= 404675606.7 N cm
Front Spar Bending Stress:
a
Bending Stress, σ z = c by
A 19 154425.68
B 14.5 117851.18
C 14.5 117851.18
D -14.5 -117851.18
E -14.5 -117851.18
F -19 -154425.68
The bending stress at various points whose co-ordinates are determined with centroid as
the origin are calculated from above formula and tabulated.
P a g e | 44
MIDDLE SPAR:
I xx = 60467.7 cm4
I yy = 5189.17 cm4
The bending moment carried by the middle spar is 40% of the total bending moment
carried by the spars.
A 20.8 159088.52
B 15.8 120846.09
C 15.8 120846.09
D -15.8 -120846.09
E -15.8 -120846.09
F -20.8 -159088.52
REAR SPAR
I xx = 2649.184 cm4
I yy = 199.46 cm4
A 8.86 966719.74
B 6.36 693943.29
C 6.36 693943.29
D -6.36 -693943.29
E -6.36 -693943.29
F -8.86 -966719.74
The bending stress at various points whose co-ordinates are determined with Centroid as
the origin are calculated from above formula and tabulated.
P a g e | 49
4
STRUCTURAL ANALYSIS AND DESIGN OF FUSELAGE
The fuselage is the main structure, or body, of the aircraft. It provides space for
personnel, cargo, controls, and most of the accessories. The power plant, wings, stabilizers, and
landing gear are attached to it.
onocoque design relies largely on the strength of the skin, or covering, to carry
The monocoque
various loads. The monocoque design may be divided into three classes - monocoque,
semimonocoque and reinforced shell.
v The true monocoque construction uses formers, frame assemblies, and bulkheads to give
shape to the fuselage. However, the skin carries the primary stresses. Since no bracing
members are present, the skin must be strong enough to keep the fuselage rigid. The
biggest problem in monocoque construction is maintaining enough strength while
keeping the weight within limits.
v Semimonocoque design overcomes the strength-to-weight problem of monocoque
construction. In addition to having formers, frame assemblies, and bulkheads, the
semimonocoque construction has the skin reinforced by longitudinal members.
v The reinforced shell has the skin reinforced by a complete framework of structural
members.
Different portions of the same fuselage may belong to any one of the three classes. Most are
considered to be of semimonocoque-type construction.
The semimonocoque fuselage is constructed primarily of aluminum alloy, although steel
and titanium are found in high-temperature areas. Primary bending loads are taken by the
longerons, which usually extend across several points of support. The longerons are
supplemented by other longitudinal members known as stringers. Stringers are more numerous
and lightweight than longerons.
The vertical structural members are referred to as bulkheads, frames, and formers. The
heavier vertical members are located at intervals to allow for concentrated loads. These members
are also found at points where fittings are used to attach other units, such as the wings and
stabilizers.
The stringers are smaller and lighter than longerons and serve as fill-ins. They have some
rigidity but are chiefly used for giving shape and for attachment of skin. The strong, heavy
longerons hold the bulkheads and formers. The bulkheads and formers hold the stringers. All of
these join together to form a rigid fuselage framework. Stringers and longerons prevent tension
and compression stresses from bending the fuselage.
The skin is attached to the longerons, bulkheads, and other structural members and
carries part of the load. The fuselage skin thickness varies with the load carried and the stresses
sustained at particular location.
v The bulkhead, frames, stringers, and longerons aid in the design and construction of a
streamlined fuselage. They add to the strength and rigidity of the structure.
v The main advantage of the semimonocoque construction is that it depends on many
structural members for strength and rigidity. Because of its stressed skin construction, a
semimonocoque fuselage can withstand damage and still be strong enough to hold
together.
P a g e | 51
Length
Equipment and Shear Bending
S.No. from Ref. Weight (N) Moment
Component Force Moment
point
1 Nose 0.58 3933.81 2281.609 3933.81 2281.809
Weight of
9 10.50 2000.68 21007.14 77861.99 489163.96
Fuselage Sheet
To determine the shear force and bending moment diagram for the wing we assume that the wing
is a cantilever beam with the root end fixed while the tail end is free.
Shear Force = Rx
fQ g
Bending Moment =
Tabulation for the values of shear force and bending moment at various positions along the span
is as follows.
100000
80000
Shear force
60000
40000
20000
0
0.58 2.02 2.62 6.62 6.63 7.92 9.85 10.32 10.5 14.23 17.1 17.6
Length from Ref. point
700000
600000
500000
400000
300000
200000
100000
0
0.58 2.02 2.62 6.62 6.63 7.92 9.85 10.32 10.5 14.23 17.1 17.6
Leght from Ref. point
Structural analysis of fuselage like that of wing is of prime importance while designing
an aircraft. As the fuselage is the one which houses the pilot, the power plant and also part of the
payload its structural integrity is a matter of concern. While analyzing the fuselage structure the
section must be idealized. Idealization involves the conversion of a stringer and its
accompanying skin thickness into a concentrated mass known as a boom. The shear flow
analysis of the fuselage simulating flight conditions is shown below.
X Y
(m) (m)
1.005 0
0.985 0.26
0.88 0.48
0.72 0.72
0.48 0.88
0.26 0.985
0 1.005
-0.26 0.985
-0.48 0.88
-0.72 0.72
-0.88 0.48
-0.985 0.26
-1.005 0
-0.985 -0.26
-0.88 -0.48
-0.72 -0.72
-0.48 -0.88
-0.26 -0.985
0 -1.005
0.26 -0.985
0.48 -0.88
0.72 -0.72
0.88 -0.48
0.985 -0.26
1.005 0
P a g e | 54
0.5
0
-1.5 -1 -0.5 0 0.5 1 1.5
-0.5
-1
-1.5
The above stringer section is uniformly used throughout the fuselage as shown above in
order to provide the fuselage the required load carrying capacity. The diagram showed adjacent
is of the idealized fuselage structure. The idealization process is carried out in the following way.
STRESS ANALYSIS:
IDEALIZATION:
where,
B1 èArea of Boom 1
By Symmetry,
B1 = B9, B2 = B8, B10 = B16, B3 = B7 , B11 = B15, B4 = B6 = Bl2 = B14 ,B5 = B13
=815582.12
B2 = 815582.12 mm2
Similarly B3 = 815582.12 mm2, B4 =815582.12 mm2. We note that stringers 5 and 13 lie on the
neutral axis of the section and are therefore unstressed; the calculation of boom areas B5 and B13
does not then arise.
We know that,
Ixx = By2
c__? = 24.67 m4; c__g = 13.77 m4; c__R = 6.12 m4; c__i = 1.11 m4
=2897784.51 × 3.8×1.5
=16517371.71 Nm
Ixx = 24.67 m4
1 5.5 3.68
2, 16 4.11 2.75
3, 15 2.74 1.83
4, 14 1.37 0.9
5, 13 0 0
6, 12 -1.37 -0.9
7, 11 -2.74 -1.83
8, 10 -4.11 -2.75
9 -5.5 -3.68
P a g e | 57
5
Design of Miscellaneous Members
Wing fuselage intersection
The 8 seater business jet aircraft has low wing configuration, thus the entire wing
structure continues in the way of airplane body.
This concept is adopted as it is the most simple and straight forward method used in
Horizon 4000 transport, during 1950s. The lift and moment loads can be carried between the
wing and fuselage by simple shear on the four pins. The drag and thrust is taken by breather web.
This design allows the wing spar and fuselage bulkheads to deflect independently of each other
such that no spar moment is directly transferred to the bulkheads.
The wing-body juncture produces aerodynamic interference which in turn promotes flow
separation with its attendant higher drag and unsteady buffeting. This adverse pressure gradient
and consequent flow separation can be minimized using contoured surface called fillet.
Engine mount
An engine mount is a frame that supports the engine and holds it to the fuselage or
nacelle. Usually it is made of built up sheet metal, welded steel tubing. The turbofan engine,
“HONEY WELL TFE731-20” is wing mounted. A typical turbofan engine installation for a
low wing aircraft configuration similar to that of this aircraft is shown below,
P a g e | 58
The pylon has three spars (longerons) – Upper, middle and lower- and three major
bulkheads, and is attached to the wing at four primary points. These are two mid
mid--spar fittings, an
upper link and a diagonal brace (drag strut). The attachment pins are secured with “fuse” bolts
which are hollow carbon steel devices that have been heat treated to shear fail at a definite load.
In the landing break way condition (wheels
(wheels-up landing);
anding); the sequence is designed to fail the
upper and lower links so that the pylon rotates around the mid
mid-spar
spar and upward. The wing pylon
design provides considerable load path redundancy such that an upper link can fail, partially or
completely, and there
ere is an alternate path
path- lower diagonal brace. The below figure shows the
engine mounts.
P a g e | 59
Empennage Design
Horizontal Stabilizer:
The horizontal tail of the aircraft is conventional and consists of a fixed tail box. The
horizontal stabilizer is usually a two spar structure consisting of a Centre structural box section
and two outer sections. The stabilizer assembly is interchangeable (symmetrical airfoil section)
as a unit at the fuselage attach points and the outer sections are interchangeable at the attachment
to the center box.
The two basic horizontal stabilizer box constructions for modern transports are
1. Box constructions with spars, closer light rib spacing (usually less than 10 inches) and
surface (may be tapered skins) without stringer reinforcement. The feature of this design
is the low manufacturing cost and high torsional stiffness require by the flutter analysis.
2. Box construction with spar stronger ribs and surface skins with stringer reinforcements
(skin-stringer or integrally stiffened panels) is a lighter weight structure.
P a g e | 60
Vertical Stabilizer:
The structural design of the vertical stabilizer is essentially the same as for the horizontal
stabilizer is essentially the same as for horizontal stabilizers. The vertical stabilizer box is a two
or multi spar structure (general aviation airplanes usually use single spar design) with cover
panels (with or without ribs). The root of the box is terminated at the aft fuselage conjuncture
with fittings or splices.
P a g e | 61
In addition to providing the required strength and stiffness, the structural box almost
always has to provide fuel space. Integral tanks, as opposed to separate internally supported
types, are preferred since their use enables the maximum advantage to be taken of the available
volume. Integrally machined or moulded constructions, which use a small amount of large
components, are obviously an advantage since sealing is reduced to a minimum. The major
problem occurs at tank end ribs, particularly in the corners of the spar web and skins, and at
lower surface access panels. The corner difficulty is overcome by using special “suitcase” corner
fittings.
Access panels should be large enough for a person to get through so that the inside can be
inspected and resealed if necessary. On shallow section wings, the access has to be in the lower
surface so that the operator can work in an acceptable way even if the depth is insufficient to
climb in completely. Apart from the sealing problems, lower surface access panels are in what is
primarily a tension skin and so introduce stress concentrations in an area where crack
propagation is a major consideration. The access panels are arranged in a span-wise line so the
edge reinforcing can be continuous and minimum stress concentration due to the cut-outs.
Access panels are often designed to carry only shear and pressure loads, the wing bending being
reacted by the edge reinforcing members. A deep wing can avoid these problems by using upper
surface access panels but this is not a preferred aerodynamic solution.
AUXILIARY SURFACES
The structural layout of the auxiliary lifting surfaces is generally similar to that of the
wing but there are differences, in part due to the smaller size and in part due to the need to
provide hinges or supports. The latter implies that each auxiliary surface is a well-defined.
Conventional training edge control surfaces are almost invariably supported by a number
of discrete hinges, although continuous, piano type, hinges may be used for secondary tabs. To
some degree the number and location of the discrete hinges depends upon the length of the
control. The major points to be considered are:
v The bending distortion of the control relative to the fixed surface must be limited so that
the nose of the control does mot fouls the fixed shroud.
v The control hinge loads and the resulting shear forces and bending moments should be
equalized as far as is possible.
v Structural failure of a single hinge should be tolerated unless each hinge is of fail-safe
design and can tolerate cracking one load path.
P a g e | 62
These points suggest the use of a relatively large number of discrete hinges but there are
difficulties associated with this solution there are the obvious loads likely to be induced in the
control by the distortion under load of the main surface to which it is attached may be significant.
These problems do not arise if only two hinge points are used as any span-wise distortion or
misalignment can be accommodated by designing one of the hinges so that it can rotate about a
vertical axis. When more than two hinges are used the „floating hinge concept cannot fully
overcome the problems. However, it is possible to design the control surface so that it is flexible
in bending and indeed the more hinges there are the easier this is to accomplish. One hinge must
always be capable of reacting side loads in the plane of the control surface. The hinges are
supported near to the aft extremities of the main surface ribs.
Some designs incorporate the pivot into the moving surface with the support bearings on
the fuselage, while on others the pivot is attached to the fuselage and the bearings are in the
surface. The bearings should be as far apart as local geometry allows minimizing loads resulting
from the reaction of the surface bending moment.
There is a wide variety of leading and trailing edge high-lift systems. Some types are
simply hinged to the wing, but many require some degree of chord-wise extension. This can be
achieved by utilizing a linkage, a mechanism, a pivot located outside the aerofoil contour or,
perhaps most commonly, by some form of track. Trailing edge flaps may consist of two or more
separate chord-wise segments, or slats, to give a slotted surface and these often move on tracts
attached to the main wing structure.
The majority of flaps and slats are split into span wise segments of no greater lengths
than can be supported at two or three locations. As with control surfaces, the locations of the
support points are established so as to minimize local deformations since the various slots are
critical in determining the aerodynamic performance. Sometimes the actuation may be located at
P a g e | 63
a different pan wise position from the support points. This is often a matter of convenience,
layout clearances, and the like.
The structural design of flaps is similar to that of control surfaces but it s simpler as there
is no requirement for mass balance, the operating mechanisms normally being irreversible. On
large trailing edge flap components, there is often more than one spar member. Especially when
this assists in reacting the support or operating loading. There may be a bending stiffness
problem in the case of relatively small chord slat segments and full depth honey combs can be
used to deal with this. Figure shows a cross section of a typical slotted flap of metal construction
but the same layout applies if composite materials are used.
In many cases the slipstream or afflux from power plants impinges upon a flap and this is
likely to require special consideration in the design. Additional stiffness is not necessarily the
answer because acoustic fatigue characteristics are often worse at higher panel frequencies.
However the extensive local support offered by sandwich construction, either in panel or full
depth configuration, is usually beneficial. This leads naturally to the application of reinforced
plastic materials. Trailing edge flaps tends to be prone to damage by debris thrown up by the
landing gear and it may be desirable to use Kevlar or glass rather than carbon fibers for the lower
surface, but material compatibility needs to be considered.
The joint of the fuselage with the wing is subjected to heavy load inputs and there is a
potential for considerable relative distortion. This distortion is usually accepted and the wing
centre box is built completely into the fuselage, the resulting constraint stresses being allowed
for. It is usual for the wing structure of large aircraft to include a production joint at the side of
the fuselage and this is virtual essential for swept wings.
It is sometimes possible to arrange the wing pick-ups as pivots on the neutral axis or set
them on swinging links. In this case, the relative motion is allowed to take place and there are no
induced stresses. Structural assembly of the wing to the fuselage is relatively simple.
Similar remarks also apply to the attachment of the horizontal stabilizer when the
incidence setting is fixed. If the surface is also used for trimming or control, some special
consideration is necessary in the location of the pivot and actuation fittings. These usually
require a relatively heavily loaded rib or a pair of ribs, and where possible at least one of the
attachment points should be close to the rib or spar intersection. It is desirable to arrange for the
lateral distance between the pivots to be as great as possible to minimize pivot loads resulting
from asymmetric span-wise loading. When the controls are manually operated, it is simplest if
the elevator-hinge line and pivot coincide.
Fins are usually built integrally with the rear fuselage. This is mainly due to the different
form of loading associated with the geometric asymmetry.
P a g e | 64
Flutter:
Flutter occurs at a critical or flutters speed Vf which in turn is defined as the lowest
airspeed at which a given structure will oscillate with sustained simple harmonic motion. Flight
at speeds below and above the flutter speed represents conditions of stable and unstable (that is
divergent) structural oscillation, respectively.
Generally, an elastic system having just one degree of freedom cannot be unstable unless
some peculiar mechanical characteristic exists such as a negative spring force or a negative
damping force. However, it is possible for systems with two or more degrees of freedom to be
unstable without possessing unusual characteristics. The forces associated with each individual
degree of freedom can interact, causing divergent oscillations for certain phase differences.
The flutter of a wing in which the flexural and torsional modes are coupled is an
important example of this type of instability. Some indication of the physical nature of wing
bending–torsion-flutter may be had from an examination of aerodynamic and inertia forces
during a combined bending and torsional oscillation in which the individual motions are 90 out
of phase. In a pure bending or pure torsional oscillation the aerodynamic forces produced by the
effective wing incidence oppose the motion; the geometric incidence in pure bending remains
constant and therefore does not affect the aerodynamic damping force, while in pure torsion the
geometric incidence produces aerodynamic forces which oppose the motion during one-half of
the cycle but assist it during the other half so that the overall effect is nil. Thus, pure bending or
pure torsional oscillations are quickly damped out. This is not the case in the combined
oscillation when the maximum twist occurs at zero bending and vice versa; i.e. a 90 phase
difference.
The type of flutter described above, in which two distinctly different types of oscillating
motion interact such that the resultant motion is divergent, is known as classical flutter. Other
types of flutter, non-classical flutter, may involve only one type of motion. For example, stalling
flutter of a wing occurs at a high incidence where, for particular positions of the span wise axis
of twist, self-excited twisting oscillations occur which, above a critical speed, diverge.
Aileron Buzz:
Another non-classical form of flutter, aileron buzz, occurs at high subsonic speeds and is
associated with the shock wave on the wing forward of the aileron. If the aileron oscillates
downwards the flow over the upper surface of the wing accelerates, intensifying the shock and
P a g e | 65
resulting in a reduction in pressure in the boundary layer behind the shock. The aileron,
therefore, tends to be sucked back to its neutral position. When the aileron raises the shock
intensity reduces and the pressure in the boundary layer increases, tending to push the aileron
back to its neutral position.
At low frequencies these pressure changes are approximately 180 out of phase with the
aileron deflection and therefore become aerodynamic damping forces. At higher frequencies a
component of pressure appears in phase with the aileron velocity which excites the oscillation. If
this is greater than all other damping actions on the aileron a high frequency oscillation results in
which only one type of motion, rotation of the aileron about its hinge, is present, i.e. aileron
buzz. Aileron buzz may be prevented by employing control jacks of sufficient stiffness to ensure
that the natural frequency of aileron rotation is high.
Buffeting:
Buffeting is produced most commonly in a tail plane by eddies caused by poor airflow In
the wing wake striking the tail plane at a frequency equal to its natural frequency; a resonant
oscillation having one degree of freedom could then occur. The problem may be alleviated by
proper positioning of the tail plane and clean aerodynamic design.
P a g e | 67
7
CONCLUSION
In conclusion, the series of short range aircrafts incorporated many unique design of
future that was never seen on an operational aircraft. The design of these aircrafts points the way
for the design of future of very high mach airplanes.
The airplane has gone through many design modifications since its early conceptual
designs expected, among these was a growth in weight. The document to provide information on
the trends in various aircraft characteristics that may influence general long-term airport planning
and design.
These are strong indications that future trends could see the coexistence of very high
capacity aircraft modules of similar capacities for the long range/very long range operations.
Cargo payloads, which include mail, express and freight, are increasing in size and weight as
larger aircraft service with the airlines,
We have enough hard work for this design project. A design never gets completed in a
flutter sense but it is one step further towards ideal system. But during the design of this aircraft,
we learnt a lot about aeronautics and its implications when applied to an aircraft design.
P a g e | 68
BIBLIOGRAPHY