Beruflich Dokumente
Kultur Dokumente
48
APPENDIX
ENTEC ENTEC
ELECTRIC & ELECTRONIC CO., LTD
Copyright © 2009 by ENTEC ELECTRIC & ELECTRONIC CO., LTD all right reserved. Forerunner Distribution & Automation
APPENDIX http://www.entecene.co.kr
Table of Contents
ENHANCED TECHNOLOGY i
APPENDIX http://www.entecene.co.kr
1.GLOBAL SETTING
1.SYSTEM
1.POWER LINE
Frequency* Power line nominal frequency (50, 60 Hz) 60
2.CURRENT SENSING
PHA CT Ratio Set phase current ratio (1~2000) 1 1000
3.VOLTAGE SENSING
1V Connect Type 1st Voltage connector (NONE, WYE, DELTA) WYE
*. NOTE ) “2V INS-Type” setting shall be Ver. 3.80 of ETR300-R or higher to be indicated. .
ENHANCED TECHNOLOGY 1
APPENDIX http://www.entecene.co.kr
Hour* Set the difference of “Hour” between UTC and Local time.(0~23hour) 1 9
Min* Set the difference of “Minute” between UTC and Local time. (0~59min) 1 0
Time Syn’ Ref* Set Reference Time Type from GPS (LOCAL, GMT) GMT
*. NOTE ) The default value of settings marked with * can vary according to the option type.
2.Communication
1. Protocol Setup
1. DNP3 Protocol Setup
SLAVE1:
ENABLE
Function Use DNP3 protocol or not (DISABLE, ENABLE)
SLAVE2:
DISABLE
SLAVE1:PORT1
COM Port Select DNP3 communication port (PORT1, PORT2, PORT3)
SLAVE2:PORT2
D/L Confirm Enable data link layer confirm (NO, YES, SOME) SOME
D/L Frame Dly’ Set Data Link frame Delay Time (10~5000msec) 10 100
SLAVE1 : 1
DNP Address Slave address (0~65534) 1
SLAVE2 : 0
SLAVE1 : 15
SBO Time Select before operate time-out (1~255 sec) 1
SLAVE2 : 30
2 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
Master IP Oct 1 Select the IP Address for DNP3 Communication (0~255) 1 192
Master IP Oct 2 Select the IP Address for DNP3 Communication (0~255) 1 168
Master IP Oct 4 Select the IP Address for DNP3 Communication (0~255) 1 202
Time Req(m) Set interval time for synchronization time (0(OFF), 1~30000 min) 1 OFF
Select Timeout* The period after a previously received select will timeout (0(OFF), 1~255sec) 1 5
ENHANCED TECHNOLOGY 3
APPENDIX http://www.entecene.co.kr
MSP Time-Tag** Time tag format for single-point (CP56, CP24) CP56
MIT Time-Tag** Time tag format for integrated totals (CP56, CP24) CP56
Time tag format for measured value and normalized value, in case of
MME Time-Tag** CP56
general event (CP56, CP24)
Time tag format for measured value and normalized value in fault
Flt Time-Tag** CP56
current event (CP56, CP24)
*. NOTE ) 1. The above setting marked with * shall be Ver. 3.6 or higher of ETR300-R to be indicated.
2. In case ETR300 is the standard type, the above setting marked with ** shall be Ver. 3.9 or higher of ETR300-R to be
indicated.
3. In case ETR300 is the External I/O option type, the above setting marked with ** shall be Ver. 4.1 or higher of
ETR300-R to be indicated.
3. IEC60870-5-104 Protocol Setup
Time Out(t2) Timeout for acking in case of no data t2<t1 (1~255 sec) 1 10
Time Out(t3) Timeout for sending test frames in case of a long idle state (1~255 sec) 1 20
Select Timeout* The period after a previously received select will timeout (0(OFF), 1~255sec) 1 5
MSP Time-Tag** Time tag format for single-point (CP56, CP24) CP56
MIT Time-Tag** Time tag format for integrated totals (CP56, CP24) CP56
Time tag format for measured value and normalized value, in case of
MME Time-Tag** CP56
general event (CP56, CP24)
Time tag format for measured value and normalized value in fault
Flt Time-Tag** CP56
current event (CP56, CP24)
4 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
COM Port Select COM Port (PORT1, PORT2, PORT3, PORT4) PORT3
2. Port Setup
1. PORT1(232) Setup
Baud Rate Select the baud rate for PORT1 (1200, 2400, 4800, 9600, 19200 bps) 9600
Parity Bit Select whether to use Parity Bit (NONE, ODD, EVEN) NONE
Modem Sel Select the type of communication wire (2W, 4W, DIAL, NONE) 4W
CTS Usage Select whether to use CTS signal or not (DISABLE, ENABLE) ENABLE
DCD Usage Set whether to use DCD signal (DISABLE, ENABLE) DISABLE
RTS Usage Select whether to use RTS Usage (OFF, ON, AUTO) AUTO
2. PORT2(485) Setup
Baud Rate Select the baud rate for PORT2 (1200, 2400, 4800, 9600, 19200 bps) 9600
Parity Bit Set whether to use Parity Bit, and set a type (NONE, ODD, EVEN) NONE
Line Type Select a physical port for communication (RS422, RS485) RS422
ENHANCED TECHNOLOGY 5
APPENDIX http://www.entecene.co.kr
keep Alive Function keep Alive Function use or not (DISABLE, ENABLE) ENABLE
4. PORTF(232) Setup
Baud Rate Baud Rate (1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200bps) 38400
6 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
AEvt Skip at Ft Select DB/TH Event Skip at fault pickup (NO, YES) NO
Daily Max I Set whether to use Daily Max I or not (DISABLE, ENABLE) DISABLE
Flt ‘I’ Evt Select the Fault ‘I’ Event (NO, YES, 1SHOT) YES
Aver. Load Calc T Set the Average Load Calculation Time (1/2/3/4/5/6/10/12/15/20/30 min) 15
BI Queue size* Set the binary queue size (32, 64, 128, 256) 256
BI Evt Mode Set the binary event mode (ALL, LAST) ALL
AI Queue size * Set the analog queue size (32, 64, 128, 256) 256
AI Evt Mode Set the analog event mode (ALL, LAST) ALL
CI Queue size * Set the counter queue size (32, 64, 128, 256) 256
CI Evt Mode Set the counter event mode (ALL, LAST) ALL
Time Syn’ Type Set the time synch type (LOCAL, GMT) LOCAL
Time Tag Type Set the time tag type (LOCAL, GMT) LOCAL
CI Frz Preiod** Set the period to freeze counter by itself. (OFF, 1~60000min.) 1 OFF
*. NOTE )1. Applicable for lower than Ver 3.5 of ETR300-R, the default value of “BI Queue size”, “AI Queue size” and “CI Queue
size” setting is “32”.
2. In case ETR300 is the standard type, the above setting marked with ** shall be Ver. 3.9 or higher of ETR300-R to be indicated.
3. In case ETR300 is the External I/O option type, the above setting marked with ** shall be Ver. 4.1 or higher of
ETR300-R to be indicated.
FTP Mode-W Select the protocol for file transfer (DNP, FTPC, FTPS, USER) DNP
FTP Dev Set the Device Type for FTP file classification (Space ~‘z’ ) REC
FTP Dev. No Set the Device Number for FTP file classification (Space ~‘z’ ) REC001
FTP ID Set the ID of the device used for the connection with FTP (Space ~‘z’ ) ENTEC
FTP Passive Select the FTP connecting method (DISABLE, ENABLE) DISABLE
3. Event Recorder
Wave Capture Select whether to use Wave capture or not (ON, OFF) ON
Wave S/R Select a number of sampling for wave capture (16, 32, 64, 128 sample) 64
ENHANCED TECHNOLOGY 7
APPENDIX http://www.entecene.co.kr
D.V. Max Set the Dead line maximum voltage (0.00~1.25) 0.01 0.50
L.V. Min Set the Live line minimum voltage (0.00~1.25) 0.01 0.85
Sync Phase Select the synchronism phase (ALL, R(AB), S(CB), T(AC) ) ALL
Time delay Set a delay time of synchronism check (0.0~180.0sec) 0.1 1.0
2.Operation Count
Function Select whether to monitor Recloser operation count (OFF, ON) OFF
Count set It is to set the same operation number of circuit breaker (0~10000) 1 0
3. Contact Wear
Function Select whether to monitor Recloser contact wear. (OFF, ON) OFF
Pickup (%) Set a number for Recloser alarming. (0.0~50.0 %) 0.1 20.0
Rated Volt(kV) Set the power line nominal voltage (15, 27, 38 kV) 27
Interrupt(kA) Enter the capacity of rated Interrupter (5.0 ~ 50.0 kA) 0.1 12.5
4. Battery Test
Period Set a time period for automatic battery test (0(OFF), 1~720 hour) 1 24
2.Interrupt
Level Set Interrupt detect level for power quality (0(OFF), 0.10~0.49 pu) 0.01 0.10
8 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
Level Set a voltage sag for power quality (0(OFF), 0.50~0.99 pu) 0.01 0.90
Time Set a time to detect voltage sag (0.5~10.0 cycle) 0.5 2.0
4. Swell
Level Set a detect level of voltage swell (0(OFF), 1.01~1.50 pu) 0.01 1.20
Time Set a time to detect voltage swell. (0.5~10.0 cycle) 0.5 2.0
5.Harmonics
VTHD Pickup Detect level of Voltage THD (0(OFF), 0.5~100.0 %) 0.1 OFF
VTHD Delay Detect time of Voltage THD (0.2~60.0 sec) 0.1 1.0
ITHD Pickup Detect level of Current THD (0(OFF), 0.5~100.0 %) 0.1 OFF
ITHD Delay Detect time of Current THD (0.2~60.0 sec) 0.1 1.0
6. Current Unbalance
Level Detect level of Current Unbalance for Power Quality (0(OFF), 1~100 %) 1 30
Time Set a detect time of current unbalance (0.1~60.0 sec) 0.1 4.0
7. Voltage Unbalance
Level Detect level of Voltage Unbalance for Power Quality (0(OFF), 1~100 %) 1 30
Time Set a detect time of voltage unbalance (0.1~60.0 sec) 0.1 4.0
8. Under Voltage
Level Set an under voltage detect level for power quality (0(OFF), 0.30~0.95pu) 0.01 0.80
Time Set an under voltage detecting time (0.0~180.0 sec) 0.1 4.0
9. Over Voltage
Level Set an over voltage detect level for power quality (0(OFF), 1.05~1.50 pu) 0.01 1.20
Time Set an over voltage detecting time (0.0~180.0 sec) 0.1 4.0
Level Set an under frequency detect level for power quality(0(OFF), 46.00~59.98 Hz) 0.01 59.50
Time Set an under frequency detecting time (0.03~10.00 sec) 0.01 3.00
Min. I Set the minimum current value to current unbalance and THD (0~630 A) 1 60
6. TD Monitor
TD1 Rate Set Transducer 1(TD1) monitoring range (1~200) 1 40
ENHANCED TECHNOLOGY 9
APPENDIX http://www.entecene.co.kr
TD1-1 Delay Set a delay time of TD1 (0.01~600.00 sec) 0.01 2.00
TD1-2 Type Set 2nd monitoring element of TD1 (UNDER, OVER) UNDER
TD1-2 PU* Set 2nd pickup value of TD1 (0(OFF), 0~6000.0) 0.1 19.0
TD1-2 Delay Set 2nd delay time of TD1 (0.01~600.00 sec) 0.01 2.00
7. Fault Locator*
Function* Fault Locator (OFF,ON) OFF
Z1(RES)* Real impedance of the feeder positive sequence (0.1-6000.0 ohms) 0.1 10.0
Z1(IND)* Imaginary impedance of the feeder positive sequence (0.1-6000.0 ohms) 0.1 10.0
Z0(RES)* Real impedance of the feeder zero sequence (0.1-6000.0 ohms) 0.1 10.0
Z0(IND)* Imaginary impedance of the feeder zero sequence (0.1-6000.0 ohms) 0.1 10.0
5. Loop Control
Type Select Set loop control function (NONE, SEC, MID, TIE) NONE
VRS to S/M The setting values are used in SEC, MID (VS, VL) VS
VRS to Tie The setting value is used in TIE (VS, VL, VS&VL) VS
CAS to Mid Select whether to use automatic setting change in MID type (OFF, ON) OFF
CAS to Tie Set value is used in TIE (OFF, VS, VL, BOTH) OFF
AR Time Setting value is used in SEC, MID (0.01~600.00 sec) 0.01 5.00
DLPT Delay Dead Bus Pickup Time Delay setting (0.01~600.00 sec) 0.01 60.00
*. NOTE ) The default value of settings marked with * can vary according to the option type.
LLPT Delay Live Bus Pickup Time Delay setting (0.01~600.00 sec) 0.01 10.00
10 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
NRT After LA Non Reclose Time After LC Action setting (0.00~600.00 sec) 0.01 15.00
6. Passcode
1.Passcode 1
2.Passcode 2
7. PLC
1.Common
1.Logic Timer
TM1-PU Set a pickup time of Logic timer 1 (0.01~600.00 sec) 0.01 0.05
TM1-DO Set a Dropout Time of Logic timer 1 (0.01~600.00 sec) 0.01 0.05
2.Pulse Timer
PTM1 Set a output time of pulse timer 1 (0.01~600.00 sec) 0.01 0.01
3. Pulse Counter
2. DI/DO
1. Input Debounce Timer
IN101 Set an Input Debounce Time of IN101 (0.005~10.000 sec) 0.001 0.020
IN301~312 is the same setting as IN101. From Ver 4.00 of ETR300-R, IN301~312 settings indicated.
OUT101 Set an Output pulse time of OUT101 (0(BUFF), 0.01~10.00 sec) 0.01 BUFF
OUT301~308 is the same setting as OUT101. From Ver 4.00 of ETR300-R OUT301~308 settings indicated.
8. Others
1. Time Display Type
TIME DISP’ TYPE Set the displays turn (YMD, MDY) MDY
ENHANCED TECHNOLOGY 11
APPENDIX http://www.entecene.co.kr
3. Vo Select
Vo SELECT* Select the zero sequence voltage (H/W, SEQ) SEQ
*. NOTE ) The default value of settings marked with * can vary according to the option type.
Interval* Setting group is changed if power flow changes during the set time.(10~180 sec) 1 30
*. NOTE ) The location of “AUTO SGRP CHANGE” menu. may be different according to the version of ETR300-R firmware.
6. H/W OPTION*
EX-IO?* Select where to install the external I/O unit ETIO10 (NO/YES) NO
2.GROUP SETTING
1.PROTECTION (Primary, Alternate, Editbank Setup)
1.Operation
Lockout-PHA Select the total number of the phase trip operations (1~5) 1 4
Lockout-GND Select the total number of the ground trip operations (1~5) 1 4
Lockout-SEF Select the total number of the SEF trip operations (1~5) 1 4
Lockout-NEG Select the total number of the negative sequence trip operations (1~5) 1 4
Fast Curve-PHA Select the number of the phase fast curve operations (0~5) 1 2
Fast Curve-GND Select a number for the ground fast curve operations (0~5) 1 2
Fast Curve-NEG Select a number for the negative sequence fast curve operations (0~5) 1 2
2.Intervals
PHASE/NEG SEQ’
OTHERS
Reset T(AR) It is to select Reset time during auto reclosing (3~180 sec) 1 30
12 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
C/P Wait Waiting time to get power supply (1.00 ~ 600.00 sec) 0.01 60.00
3.Pickup Current
Phase Set the pickup current of Phase (OFF,10~1600A) 1 500
Neg Seq’ Set the pickup current of negative sequence (OFF,10~1600A) 1 500
4.Phase Fast
Curve Select the desired curve type (A(101), B(117), ..., DEF-10S) ANSI-V1
*. NOTE ) Applicable for lower than 3.4 of ETR300-R, the default value of “Curve” setting is “ANSI-NI”.
Time Dial Select Time dial and multiply it to selected curve. (0.05~15.00) 0.01 1.00
Time Add Select Time adder and add it on the curve (0.00~10.00 sec) 0.01 0.00
Reset Method Select the reset method of phase fast protection. (INST, LINEAR) INST
Low Set DT Set trip time to be a definite time. (0(OFF), 1~ 600sec) 1 OFF
5.Phase Delay: The setting is very similarly to the phase fast setting.
6.Ground Fast
1.Ground Fast Setup
Curve Select the desired curve type (A(101), B(117), ..., DEF-10S) ANSI-V1
*. NOTE ) Applicable for lower than 3.4 of ETR300-R, the default value of “Curve” setting is “ANSI-NI”.
Time Dial Select Time dial and multiply it to selected curve (0.05~15.00) 0.01 1.00
Time Add Select Time adder and add it on the curve (0.00~10.00 sec) 0.01 0.00
Reset Method Select the reset method of phase fast protection. (INST, LINEAR) INST
Low Set DT Set trip time to be a definite time. (0(OFF), 1~ 600sec) 1 OFF
7.Ground Delay: The setting is very similarly to the Ground fast setting.
8.SEF Element
SEF delay time set
(Applicable for lower than Ver. 3.94 of ETR300-R : 0.0~180.0 sec,
Time Delay Applicable for Ver. 3.94~3.99 of ETR300-R : 0.0~600.0 sec, 0.1 5.0
Applicable for Ver. 4.00~4.16 of ETR300-R : 0.0~180.0 sec,
Applicable for Ver. 4.17 or higher of ETR300-R : 0.0~600.0 sec)
ENHANCED TECHNOLOGY 13
APPENDIX http://www.entecene.co.kr
*. NOTE ) Applicable for lower than Ver. 3.4 of ETR300-R, the default value of “Curve” setting is “ANSI-NI”.
Time Dial Select Time dial and multiply it to selected curve (0.05~15.00) 0.01 0.50
Time Add Select Time adder and add it on the curve (0.00~10.00 sec) 0.01 0.00
Reset Method Select the reset method of phase fast protection. (INST, LINEAR) INST
Low Set DT Set trip time to be a definite time. (0(OFF), 1~ 600sec) 1 OFF
11.NEG SEQ Delay: The setting is very similarly to the NEG SEQ Fast setting.
12.Phase High Current Trip (50P-1)
Sequence Active trip(0(OFF),1~5) 1 1
Pickup Set the pickup current of Phase High current Trip(0(OFF), 10~20000 A) 1 4000
Pickup Set the pickup current of Ground High current Trip(0(OFF), 10~20000 A) 1 4000
Pickup Set the pickup current of NEG High current trip(0(OFF), 10~20000 A) 1 4000
Pickup Set pickup current of Phase High Current Lockout (0(OFF),10~20000 A) 1 8000
14 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
Pickup Set pickup current of Ground High Current Lockout (0(OFF), 10~20000 A) 1 8000
Pickup Set pickup current of NEG High Current Lockout (0(OFF), 10~20000 A) 1 8000
PHA(A) Set phase inrush current restraint value (0(OFF), 10~20000A) 1 2000
Curve-PHA Select the desired curve type (A(101), B(117), ..., DEF-10S) N3
Time Dial-PHA Set a coefficient to apply to a set curve (0.05~15.00) 0.01 1.00
Time Addr-PHA Adding a time onto a set curve (0.00~10.00 sec) 0.01 0.00
GND(A) Set ground inrush current restraint value (0(OFF), 10~20000A) 1 2000
Curve-GND Select the desired curve type (A(101), B(117), ..., DEF-10S) N3
Time Dial-GND Set a coefficient to apply to a set curve (0.05~15.00) 0.01 1.00
Time Addr-GND Adding a time onto a set curve (0.00~10.00 sec) 0.01 0.00
M.R.T- GND Minimum Response Time setting (0.00~10.00 sec) 0.01 0.00
NEG(A) Set negative inrush current restraint value (0(OFF), 10~20000A) 1 2000
ENHANCED TECHNOLOGY 15
APPENDIX http://www.entecene.co.kr
Time Dial- NEG Set a coefficient to apply to a set curve (0.05~15.00) 0.01 1.00
Time Addr- NEG Adding a time onto a set curve (0.00~10.00 sec) 0.01 0.00
M.R.T- NEG Minimum Response Time setting (0.00~10.00 sec) 0.01 0.00
SEF(A) Set SEF inrush current restraint value (0(OFF), 0.1~2000.0A) 0.1 20
Outage Time Set a time to disable Cold load pickup (0.00~600.00 sec) 0.01 1.0
RMT Func-PHA Set whether to use Phase Minimum operation current reset function (OFF, ON) ON
Select the restore minimum time required for the inrush load
RMT Time-PHA (Applicable for lower than Ver 3.4 of ETR300-R : 0.00~60.00 sec, 0.01 3.00
Applicable for Ver 3.4 or higher of ETR300-R : 0.00~600.00 sec)
Cold load pickup Reset Time setting on phase inrush current
Rst Time-PHA (Applicable for lower than Ver 3.4 of ETR300-R : 0.00~60.00 sec, 0.01 3.00
Applicable for Ver 3.4 or higher of ETR300-R : 0.00~600.00 sec)
RMT Func-GND Set whether to use ground Minimum operation current reset function (OFF, ON) ON
Select the restore minimum time required for the inrush load
RMT Time-GND (Applicable for lower than Ver 3.4 of ETR300-R : 0.00~60.00 sec, 0.01 3.00
Applicable for Ver 3.4 or higher of ETR300-R : 0.00~600.00 sec)
Cold load pickup Reset Time setting on ground inrush current
Rst Time-GND (Applicable for lower than Ver 3.4 of ETR300-R : 0.00~60.00 sec, 0.01 3.00
Applicable for Ver 3.4 or higher of ETR300-R : 0.00~600.00 sec)
RMT Func-NEG Set whether to use negative Minimum operation current reset function (OFF, ON) ON
Select the restore minimum time required for the inrush load
RMT Time- NEG (Applicable for lower than Ver 3.4 of ETR300-R : 0.00~60.00 sec, 0.01 3.00
Applicable for Ver 3.4 or higher of ETR300-R : 0.00~600.00 sec)
Cold load pickup Reset Time setting on negative inrush current
Rst Time- NEG (Applicable for lower than Ver 3.4 of ETR300-R : 0.00~60.00 sec, 0.01 3.00
Applicable for Ver 3.4 or higher of ETR300-R : 0.00~600.00 sec)
RMT Func-SEF Set whether to use SEF Minimum operation current reset function (OFF, ON) ON
Select the restore minimum time required for the inrush load
RMT Time- SEF (Applicable for lower than Ver 3.4 of ETR300-R : 0.00~60.00 sec, 0.01 3.00
Rst Time- SEF (Applicable for lower than Ver 3.4 of ETR300-R : 0.00~60.00 sec, 0.01 3.00
Make Use ‘I’ This setting changes the time of cold load pickup actives.(NO,YES) NO
E-CLP Multi’ Set the multiple of cold load. (1.0~5.0) 0.1 2.0
16 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
M.P.V Set Minimum Polarizing to check Phase disconnect direction (0(OFF), 10~80%) 1 30
BLOCK OC Select whether to block the phase polarizing trip (NO, YES) NO
M.P.V Set Minimum Polarizing Voltage to check ground fault direction. (0(OFF), 10~80%) 1 30
BLOCK OC Select whether to block the ground polarizing trip (NO, YES) NO
M.P.V Set Minimum Polarizing Voltage to check Negative Sequence direction.(0(OFF), 10~80%) 1 30
BLOCK OC Select whether to block the NEG polarizing trip. (NO, YES) NO
M.P.V Set Minimum Polarizing Voltage to check Negative Sequence direction.(0(OFF), 10~80%) 1 30
BLOCK OC Select whether to block the NEG polarizing trip. (NO, YES) NO
20.Voltage
1. Under/ Over voltage1 (27)
UV1 Function Under voltage function setting .(OFF, TR, AL, TR&AL) OFF
UV1 Delay Set time delay for UV1 (0.00~600.00 sec) 0.01 5.00
OV1 Function Over Voltage function setting (OFF, TR, AL, TR&AL) OFF
OV1 Delay Time Delay for OV1 (0.00~600.00 sec) 0.01 5.00
NVCL Func’ Select whether to close when normal voltage inputs.(OFF, ON) OFF
ENHANCED TECHNOLOGY 17
APPENDIX http://www.entecene.co.kr
UV1 NVCL Lv Set the normal voltage based on under voltage(0.10~1.40xVT) 0.01 0.95
OV1 NVCL Lv Set the normal voltage based on over voltage(0.10~1.40xVT) 0.01 1.05
2. Under /Over voltage2 (27): It is the same setting as 1. Under/ Over voltage1 (27)
21.Frequency
1.Under / Over frequency
UF TD Time Delay for under frequency detected. (0.00~600.00 sec) 0.01 2.00
OF TD Time Delay for over frequency detected. (0.00~600.00 sec) 0.01 2.00
Min. V Minimum Voltage for frequency protection actives.(0.00~1.25 x VT) 0.01 0.10
NFCL Func’ Select whether to close when normal voltage inputs.(OFF, ON) OFF
UF NFCL Lv Set the normal frequency based on under frequency.(40.00~65.00Hz) 0.01 59.80
OF NFCL Lv Set the normal frequency based on over frequency.(40.00~65.00Hz) 0.01 60.20
22.User Curve
1.User Curve1
Live Level Set pickup level of live line (0.10~0.90pu) 0.01 0.80
*. NOTE ) The default value of settings marked with * can vary according to the option type.
Detect Time Set a time to detect live line in load side (0~60000msec) 5 5
18 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
Live Line Tm Set the delay time of live detect element (0.0~18 0.0sec) 0.1 4.0
26.Demand
Function Demand setting (OFF, TR, AL, TR&AL) TRIP
Interval Set the interval to calculate Demand current (5, 10, 15, 20, 30, 60 min) 5
PHA Pickup Set the Pickup current of phase Demand. (0(OFF), 10~1600A) 1 600
PHA Time Delay Set the detect delay time of phase Demand. (0.00~600.00 sec) 0.01 10.00
GND Pickup Set the Pickup current of ground Demand. (0(OFF), 10~1600A) 1 300
GND Time Delay Set the detect delay time of ground Demand.(0.00~600.00 sec) 0.01 10.00
NEQ Time Delay Set the detect time of NEQ-PHA Demand. (0.00~600.00 sec) 0.01 10.00
D/T M-Close Time delay for manual close (0.00~600.00 sec) 0.01 0.00
Detect Time Set delay time of phase open or loss (0.0~180.0sec) 0.1 4.0
*. NOTE ) Applicable for lower than Ver. 3.4 of ETR300-R, the default value of “PHA-Pickup” setting is “400A”.
PHA-Time Set the detect time of phase alarm Current.(0.0~180.0 sec) 0.1 2.0
GND-Pickup Set the pickup value of ground Alarm Current. (0(OFF), 10~1600A) ) 1 OFF
*. NOTE ) Applicable for lower than Ver. 3.4 of ETR300-R, the default value of “GND-Pickup” setting is “70A”.
GND-Time Set the detect time of ground Alarm Current.(0.0~180.0 sec) 0.1 2.0
NEG-Pickup Set the pickup value of NEG Alarm Current.(0(OFF), 10~1600A) 1 OFF
*. NOTE ) Applicable for lower than Ver. 3.4 of ETR300-R, the default value of “NEG-Pickup” setting is “400A”.
NEG-Time Set the detect time of NEG alarm Current. (0.0~180.0 sec) 0.1 2.0
ENHANCED TECHNOLOGY 19
APPENDIX http://www.entecene.co.kr
Time Delay Set the delay time for loss of phase detected.(0.10~100.00) 0.01 20.00
2.Select Setbank
Primary Select a Bank of Primary setting group. (BANK 1~6) BANK1
20 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
ENHANCED TECHNOLOGY 21
APPENDIX http://www.entecene.co.kr
48 DIGDO DIAGNOSTIC DO
22 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
64 DO0C DO 0 - CLOSE
65 DO0T DO 0 - TRIP
66 DO10C DO 10 - CLOSE
67 DO10T DO 10 - TRIP
68 DO11C DO 11 - CLOSE
69 DO11T DO 11 - TRIP
70 DO12C DO 12 - CLOSE
71 DO12T DO 12 - TRIP
72 DO13C DO 13 - CLOSE
73 DO13T DO 13 - TRIP
74 DO14C DO 14 - CLOSE
75 DO14T DO 14 - TRIP
76 DO15C DO 15 - CLOSE
77 DO15T DO 15 - TRIP
78 DO16C DO 16 - CLOSE
79 DO16T DO 16 - TRIP
80 DO17C DO 17 - CLOSE
81 DO17T DO 17 - TRIP
82 DO18C DO 18 - CLOSE
83 DO18T DO 18 - TRIP
84 DO19C DO 19 - CLOSE
85 DO19T DO 19 - TRIP
86 DO1C DO 1 - CLOSE
87 DO1T DO 1 - TRIP
88 DO20C DO 20 - CLOSE
ENHANCED TECHNOLOGY 23
APPENDIX http://www.entecene.co.kr
89 DO20T DO 20 - TRIP
90 DO21C DO 21 - CLOSE
91 DO21T DO 21 - TRIP
92 DO22C DO 22 - CLOSE
93 DO22T DO 22 - TRIP
94 DO23C DO 23 - CLOSE
95 DO23T DO 23 - TRIP
96 DO24C DO 24 - CLOSE
97 DO24T DO 24 - TRIP
98 DO25C DO 25 - CLOSE
99 DO25T DO 25 - TRIP
24 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
ENHANCED TECHNOLOGY 25
APPENDIX http://www.entecene.co.kr
26 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
ENHANCED TECHNOLOGY 27
APPENDIX http://www.entecene.co.kr
28 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
ENHANCED TECHNOLOGY 29
APPENDIX http://www.entecene.co.kr
30 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
ENHANCED TECHNOLOGY 31
APPENDIX http://www.entecene.co.kr
32 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
ENHANCED TECHNOLOGY 33
APPENDIX http://www.entecene.co.kr
34 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
* AND
+ OR
! NOT
( ) BRACKET
ENHANCED TECHNOLOGY 35
APPENDIX http://www.entecene.co.kr
36 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
53 LSET13 0 LATCH-13SET
ENHANCED TECHNOLOGY 37
APPENDIX http://www.entecene.co.kr
38 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
ENHANCED TECHNOLOGY 39
APPENDIX http://www.entecene.co.kr
40 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
ENHANCED TECHNOLOGY 41
APPENDIX http://www.entecene.co.kr
42 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
ENHANCED TECHNOLOGY 43
APPENDIX http://www.entecene.co.kr
44 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
ENHANCED TECHNOLOGY 45
APPENDIX http://www.entecene.co.kr
46 ENHANCED TECHNOLOGY
APPENDIX http://www.entecene.co.kr
*. NOTE ) The above setting marked with * shall be Ver. 4.0 or higher of ETR300-R to be indicated.
ENHANCED TECHNOLOGY 47