Beruflich Dokumente
Kultur Dokumente
Contents
7.4.51 State Transition
WCDMA RAN
State Transition Feature Parameter
Description
Issue 04
Date 2016-08-30
and other
All other Huaweiand
trademarks trademarks are trademarks
trade names mentioned of Huawei
in this Technologies
document are the Co., Ltd. of their respective holders.
property
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and
recommendations in this document are provided "AS IS" without warranties, guarantees or representations of
any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Email: support@huawei.com
7.4.51 Contents
1 About This Document
1.1 Scope
1.2 Intended Audience
1.3 Change History
1.4 Differences Between Base Station Types
2 Overview
2.1 UE State Transitions
2.2 RRC Connection States
2.3 UE State Transition Types
2.4 Relationships Between Service Type and State Transition
2.5 Trigger Conditions for UE State Transitions
7 Network Impact
7.1 WRFD-010202 UE State in Connected Mode (CELL-DCH, CELL-PCH, URA-PCH, CELL-FACH)
7.2 WRFD-01061111 HSDPA State Transition
8 Engineering Guidelines
8.1 CELL_DCH State Transition
8.1.1 When to Use CELL_DCH State Transition
8.1.2 Required Information
8.1.3 Deployment
8.1.4 Performance Monitoring
8.2 CELL_PCH State Transition
8.2.1 When to Use CELL_PCH State Transition
8.2.2 Required Information
8.2.3 Deployment
8.2.4 Performance Monitoring
8.3 URA_PCH State Transition
8.3.1 When to Use URA_PCH State Transition
8.3.2 Required Information
8.3.3 Deployment
8.3.4 Performance Monitoring
8.4 WRFD-01061111 HSDPA State Transition
8.4.1 Requirements
8.4.2 Data Preparation
8.4.3 Activation
8.4.4 Activation Observation
8.4.5 Deactivation
8.4.6 MML Command Examples
8.5 Fast State Transition
8.5.1 When to Use Fast State Transition
8.5.2 Deployment
8.5.3 Performance Monitoring
8.6 Air Interface Exception-based H2F State Transition
8.6.1 When to Use Air Interface Exception-based H2F State Transition
8.6.2 Deployment
8.6.3 Performance Monitoring
8.7 Throughput-based D2F/D2P State Transition
8.7.1 When to Use Throughput-based D2F/D2P State Transition
8.7.2 Deployment
8.7.3 Performance Monitoring
8.8 D2F State Transition Based on Release of Combined Services
8.8.1 When to Use D2F State Transition Based on Release of Combined Services
8.8.2 Deployment
8.8.3 Performance Monitoring
8.9 Wait Time-based F2D State Transition
8.9.1 When to Use Wait Time-based F2D State Transition
8.9.2 Deployment
8.9.3 Performance Monitoring
8.10 Smart P2D State Transition
8.10.1 When to Use Smart P2D
8.10.2 Deployment
8.10.3 Performance Monitoring
8.11 Load- and Ec/No-based P2D State Transition
8.11.1 When to Use Load- and Ec/No-based P2D State Transition
8.11.2 Deployment
8.11.3 Performance Monitoring
8.12 Out-of-Service Scenario Optimization
8.12.1 When to Use Out-of-Service Scenario Optimization
8.12.2 Deployment
8.12.3 Performance Monitoring
8.13 Function of Handling State Transition Failures
8.13.1 When to Use the Function of Handling Abnormal Cell Updates of UEs in the URA_PCH State
8.13.2 Deployment
8.13.3 Performance Monitoring
8.14 Function of Optimizing Overlaps Between State Transitions and Other Procedures
8.14.1 When to Use the Function of Optimizing Overlaps Between State Transitions and Other Procedures
8.14.2 Deployment
8.14.3 Performance Monitoring
8.15 H2F Data Transmission Optimization
8.15.1 When to Use H2F Data Transmission Optimization
8.15.2 Deployment
8.15.3 Performance Monitoring
8.16 Service-based F2D State Transition Enhancement
8.16.1 When to Use Service-based F2D State Transition Enhancement
8.16.2 Deployment
8.16.3 Performance Monitoring
8.17 H2F-oriented Event 4A Measurement Optimization
8.17.1 When to Use H2F-oriented Event 4A Measurement Optimization
8.17.2 Deployment
8.17.3 Performance Monitoring
9 Parameters
10 Counters
11 Glossary
12 Reference Documents
1.1 Scope
This document describes state transition, including its technical principles, related features,
network impact, and engineering guidelines.
This document covers the following features:
WRFD-010202 UE State in Connected Mode (CELL-DCH, CELL-PCH, URA-PCH,
CELL-FACH)
WRFD-01061111 HSDPA State Transition
This document requires that readers know the dynamic channel configuration control (DCCC)
mechanism. It is recommended that readers read DCCC Feature Parameter Description beforehand.
This document applies to the following types of network elements (NEs).
NE Type Model
Micro BTS3911E
This section provides information about the changes in different document versions. There are
two types of changes, which are defined as follows:
Feature change
Changes in features and parameters of a specified version as well as the affected entities
Editorial change
Changes in wording or addition of information and any related parameters affected by
editorial changes. Editorial change does not specify the affected entities.
RAN18.1 04 (2016-08-30)
RAN18.1 03 (2016-04-28)
RAN18.1 02 (2016-03-28)
RAN18.1 01 (2016-02-29)
NOTE:
N/A indicates that an NE is not involved, that is, a feature does not require the support of the NE.
2 Overview
shows UE state transitions. For details, see section 7.1 "Overview of RRC States and
Figure 2-1
State Transitions including GSM and E-UTRA" in 3GPP TS 25.331 V9.4.0.
State transitions between idle mode and UTRAN connected mode
State transitions in UTRAN connected mode
Figure 2-1 UE state transitions
After a UE sets up a radio resource control (RRC) connection, it enters the UTRAN connected
mode. The RNC monitors UE behavior and controls UE state transitions. When there are data
transmission requirements, services can be processed in time. When there is no data transmission
requirement, network resources can be saved.
Huawei helped achieve state transitions between idle mode and UTRAN connected mode as well
as state transitions in UTRAN connected mode.
2.2 RRC Connection States
This section describes the WRFD-010202 UE State in Connected Mode (CELL-DCH, CELL-
PCH, URA-PCH, CELL-FACH) feature.
After a UE sets up an RRC connection, it enters UTRAN connected mode. The four states in
UTRAN connected mode are as follows:
CELL_DCH state
A UE in this state occupies dedicated channel resources and consumes a large amount of
radio resources. This state is suitable for high-speed data transmission.
After HSPA is introduced, the CELL_DCH state is categorized as follows:
CELL_DCH state (carried over the DCH)
CELL_DCH state for HSDPA services (carried over the HS-DSCH)
CELL_DCH state for HSUPA services (carried over the E-DCH)
The involved feature is WRFD-01061111 HSDPA State Transition.
CELL_FACH state
A UE in this state uses the common channel to send or receive data, which occupies only a
small amount of resources. Because of resource limitations on the RACH and FACH, the
CELL_FACH state is suitable for low-speed data transmission.
CELL_PCH state
In the uplink, a UE in this state cannot transmit signaling messages. If the UE has data to
transmit on the uplink, it needs to go through the cell update procedure to transit to the
CELL_FACH or CELL_DCH state.
In the downlink, the UE uses discontinuous reception (DRX) to monitor messages on the
PCH at a given moment. The purpose is to receive paging messages. If a UE in the
CELL_PCH state is in the WCDMA network, the UTRAN can obtain the serving cell of the
UE and page the UE within the serving cell. After moving to another cell, the UE needs to
send a CELL UPDATE message to perform cell reselection.
Some UEs on the live network are incompatible with this function. It is recommended these
UEs be blacklisted when this function is enabled. UEs in the blacklist are not allowed to
enter the CELL_PCH state.
For details about how to blacklist UEs, see Terminal Black List Feature Parameter
Description. Before enabling this function, set TAC_FUNC(BSC6900,BSC6910) to
Special_User_Enhance and select PCH_DISABLED_SWITCH under
SpecUserFunctionSwitch.
URA_PCH state
This state differs from the CELL_PCH state in that, if the UE in the URA_PCH state is on a
WCDMA network, the UTRAN can learn which UTRAN registration area (URA) the UE is
in and can page the UE within this URA. After moving to another URA, the UE needs to
send a URA UPDATE message to perform a URA update.
Some UEs on the live network are incompatible with this function. It is recommended these
UEs be blacklisted when this function is enabled. UEs in the blacklist are not allowed to
enter the URA_PCH state.
For details about how to blacklist UEs, see Terminal Black List Feature Parameter
Description. Before enabling this function, set TAC_FUNC(BSC6900,BSC6910) to
Special_User_Enhance and select PCH_DISABLED_SWITCH under
SpecUserFunctionSwitch. Alternatively, set TAC_FUNC(BSC6900,BSC6910) to
Special_User_Enhance and select SPECUSER_URA_PCH_DISABLED_SWITCH
under SpecUserFunctionSwitch(BSC6900,BSC6910).
2.3 UE State Transition Types
Table 2-1 lists the UE state transition types in UTRAN connected mode.
Table 2-1 UE state transition types in UTRAN connected mode
State Reference Channel Type Description
Transition Shifting
Low 3.2 Low - If a UE performing best effort (BE) services stays in the
activity Activity CELL_DCH state and cannot perform a state transition,
State
state Transition the RNC enables the BE services to enter the low activity
state, which is configured with lower rates, to save DCH
resources.
The relationships between service type and state transition are as follows:
A UE stays in CELL_DCH when performing circuit switched (CS) services. State
transitions are not allowed.
A UE can be switched only between CELL_DCH and CELL_FACH when performing
streaming services.
A UE can be switched between any states when performing BE services.
2.5 Trigger Conditions for UE State Transitions
Event 4B: As shown in Figure 2-3, if the traffic volume or throughput stays below the
event 4B threshold, event 4B is reported, which may trigger state transitions.
Figure 2-3 Traffic volume or throughput stays below the event 4B threshold
Cell reselection
If the number of cell reselections exceeds a specified threshold during a specified period of
time, the UE is considered to be in the state of frequent cell reselections, which may trigger
P2U state transitions.
UE reentering service area
A UE in URA_PCH state initiates a CELL UPDATE procedure after reentering the service
area, and the cause value of the CELL_Update message is Re-entered Service Area, which
triggers U2U state transmissions.
UE mobility
When a UE moves to a weak coverage area, the UE falls back from the E-DCH to the DCH.
When the UE then moves to an area with sufficient coverage, it performs a D2E retry for
DCCC based on the traffic volume. For details, see 3.10 D2D State Transition.
Paging or data transmission
When the UTRAN pages a UE or a UE intends to transmit data, state transmissions may be
triggered.
Cell overload
When a cell is overloaded, the RNC transits the UE state from CELL_DCH (DCH/HS-
DSCH/E-DCH) to CELL_FACH (FACH) to relieve cell load.
Historical records of data transmission
The RNC predicts future data transmission behavior of a UE based on historical records:
If the previous transmission interval for a UE was long, the RNC predicts that the
subsequent transmission interval will be long. When the UE completes data
transmission, the RNC quickly transits the UE state from CELL_DCH to CELL_PCH,
URA_PCH, or CELL_FACH. For details, see 3.13 Smart Fast State Transition.
If a UE has transmitted a large amount of data for multiple consecutive times, the RNC
predicts that the UE will transmit a large amount of data next time. When the UE
transmits data next time, the RNC will transit the UE state from CELL_PCH,
URA_PCH, or CELL_FACH to CELL_DCH through a cell update. For details, see
3.11.1 Smart P2D State Transition.
User experience
When the FACH is congested, the FACH congestion-based event 4A threshold for
FACH2DCH/FACH2HSPA channel switch of BE services is used to control F2D state
transitions, thereby relieving the FACH congestion. For details, see 3.9.2 F2D State
Transition Caused by FACH Congestion.
When a cell is not congested and has high signal quality, P2D state transitions can be
triggered to improve user experience in the delay of data transmission. For details, see
3.11.2 Load- and Ec/No-based P2D State Transition.
Principles
The D2F state transition applies to all services except CS voice services. When a UE is in low
mobility, a D2F state transition can save network resources.
Figure 3-1 shows the D2F state transition.
Figure 3-1 D2F state transition
D2F state transition has the following types of channel shifting (see section 2.3 UE State Transition
Types for details):
D2F and H2F channel type shifting uses traffic volume-based event 4B measurement.
E2F channel type shifting uses throughput-based event 4B measurement.
If the actual traffic volume or throughput of a service stays below the event 4B threshold for a
period specified by "Time to trigger", event 4B is reported. In addition, event 4B cannot be
reported again during the period specified by "Pending time after trigger" to prevent repeated
reporting of event 4B from wasting system resources. See Table 3-1 for the parameters related to
the event 4B threshold, "Time to trigger", and "Pending time after trigger."
When receiving a report on event 4B, the RNC starts the timer for D2F state transition and the
counters for UL and DL event 4B reports. If the number of UL and DL event 4B reports is
greater than or equal to the corresponding D2F transition threshold before the timer expires, then
the D2F state transition is performed when the timer expires. See Table 3-1 for the parameters
related to the D2F state transition timer.
The D2F state transition threshold is the rounded-down value obtained by using the following
formula:
D2F transition threshold = D2F transition time/ (Time to trigger + Pending time after trigger) x
State transition traffic redundancy coefficient
In this equation:
The D2F state transition time, time to trigger, and pending time after trigger are specified by
the parameters listed in Table 3-1.
The state transition traffic redundancy coefficient is used to prevent false detection that a UE
is in the low-activity state due to the loss of measurement reports. This coefficient is
configured by using the STATETRANSTRAFFREDUNDCOEF(BSC6900,BSC6910)
parameter.
NOTE:
If the uplink and downlink of a BE service are carried on two different channels, the D2F state transition time
equals the larger value of the D2F state transition time for the two channels, and (Time to trigger + Pending
time after trigger) equals the actual value configured for the channels.
In the case of combined PS services (PS BE service+PS BE service or PS BE service+PS real-time service), if
one of the services meets the state transition conditions, the service first enters the low activity state. A state
transition is performed until the other service also meets the state transition conditions.
In the case of PS BE+CS combined services, if the PS BE service meets the state transition conditions, the
service first enters the low activity state and then the UE performs state transition after the CS service is
released.
1. When adding cell-level state transition parameters, you are advised to modify the following
cell-level parameters: D2F2PTvmThd(BSC6900,BSC6910),
BeH2FTvmThd(BSC6900,BSC6910), E2FThrouThd(BSC6900,BSC6910),
BeF2DTvmThd(BSC6900,BSC6910), BeF2HTvmThd(BSC6900,BSC6910),
BeF2ETvmThd(BSC6900,BSC6910), and
FastDormancyF2DHTvmThd(BSC6900,BSC6910)
2. It is good practice to configure cell-level state transition thresholds as follows. Otherwise,
ping-pong state transition may occur.
D2F2PTvmThd(BSC6900,BSC6910)<BeF2DTvmThd(BSC6900,BSC6910);
D2F2PTvmThd(BSC6900,BSC6910)<
FastDormancyF2DHTvmThd(BSC6900,BSC6910);
BeH2FTvmThd(BSC6900,BSC6910)<BeF2HTvmThd(BSC6900,BSC6910);
BeH2FTvmThd(BSC6900,BSC6910)<
FastDormancyF2DHTvmThd(BSC6900,BSC6910);
If the uplink and downlink of a BE service are carried on different channels, the RNC identifies
the uplink and downlink and selects different parameters according to Table 3-1.
After the D2F state transition switch is turned on, whether the D2F state transition takes effect
also depends on DCCC.
The details are as follows: If DraSwitch(BSC6900,BSC6910) is set to
DRA_DCCC_SWITCH-1 and DcccStg(BSC6900,BSC6910) is set to
RATE_UP_AND_DOWN_ON_DCH,
D2F channel type shifting in D2F state transitions takes effect if the uplink/downlink rate is
lower than or equal to
UlDcccRateThd(BSC6900,BSC6910)/DlDcccRateThd(BSC6900,BSC6910).
If DraSwitch(BSC6900,BSC6910) is set to DRA_DCCC_SWITCH-1 and
DcccStg(BSC6900,BSC6910) is set to RATE_UP_ONLY_ON_DCH,
D2F channel type shifting in D2F state transitions takes effect.
If DraSwitch(BSC6900,BSC6910) is not set to DRA_DCCC_SWITCH-0,
D2F channel type shifting in D2F state transitions takes effect.
If DraSwitch(BSC6900,BSC6910) is set to DRA_DCCC_SWITCH-1 and
DRA_HSUPA_DCCC_SWITCH-1,
E2F channel type shifting in D2F state transitions takes effect when the uplink rate of an
HSUPA user drops to the minimum rate in the uplink rate adjustment set for HSUPA
services.
Table 3-2 lists the switch parameters related to the D2F state transition.
Table 3-2 Switch parameters related to the D2F state transition
NOTE:
If the current service type is non-HSPA, the D2F state transition switch of this service is independent of HSPA
service switch parameters.
For non-PTT services, to prevent ping-pong state transitions between CELL_DCH and
CELL_FACH, turn on PERFENH_H2F_OPT_SWITCH under the
PerfEnhanceSwitch(BSC6900,BSC6910) parameter. After PERFENH_H2F_OPT_SWITCH is
turned on, event 4A and 4B measurements start. If the RNC receives an event 4A report before
the D2F state transition timer expires, and if the uplink throughput is higher than
HSUPA4AThrouThd(BSC6900,BSC6910) or the downlink throughput is higher than
HSDPA4ATvmThd(BSC6900,BSC6910), the RNC stops the D2F state transition timer to prevent
unnecessary state transitions.
After D2F state transitions are optimized, event 4A measurement over HSDPA is optimized to
prevent ping-pong H2F state transitions of HSDPA services. The optimization function is
controlled by PERFENH_HSDPA_4AMEAS_OPTIMIZE_SWITCH under the
PerfEnhanceSwitch6(BSC6900,BSC6910) parameter.
After PERFENH_HSDPA_4AMEAS_OPTIMIZE_SWITCH is selected, if a cell is in the
light load state (that is, the load state of the cell is lighter than the LDR state), the event 4A
measurement mechanism is optimized as follows: L2 layer sends event 4A measurement reports
if the current buffer occupation (BO) value or the maximum traffic volume during each
scheduled data transmission in the current measurement period is greater than the event 4A
threshold. If a cell is in the LDR state, the event 4A measurement mechanism remains
unchanged. That is, L2 layer sends event 4A measurement reports only when both the current BO
value and the maximum traffic volume during each scheduled data transmission in the current
measurement period are greater than the event 4A threshold.
NOTE:
For details about the event 4A measurement mechanism for cells in the LDR state, see section 3.2 "Basic Congestion
Triggering" in Load Reshuffling Feature Parameter Description.
After the throughput-based D2F/D2P state transition function is enabled, this optimization function does not take
effect.
For PTT services, to prevent ping-pong state transitions between CELL_DCH and CELL_FACH,
turn on IUR_HHO_ASYNC_CTRL_SWITCH under the
PROCESSSWITCH4(BSC6900,BSC6910) parameter to start event 4A and 4B measurements. If
the RNC receives an event 4A report for PTT services before the D2F state transition timer
expires, and if either of the following conditions is met, the RNC stops the D2F state transition
timer to prevent unnecessary state transitions:
The measured value of uplink throughput carried in the event 4A report is greater than the
value of PTTE2FTHROUTHD(BSC6900,BSC6910) plus 10 bit/s.
The measured value of downlink traffic volume carried in the event 4A report is greater than
the high-level threshold for PTTDH2FTVMTHD(BSC6900,BSC6910). For example, if
PTTDH2FTVMTHD(BSC6900,BSC6910) is set to 8 bytes, the downlink traffic volume must
be greater than 16 bytes to meet this condition. In this example, "16 bytes" is the high-level
threshold of "8 bytes."
NOTE:
The value range of PTTDH2FTVMTHD(BSC6900,BSC6910) is 8, 16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k,
8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k. The unit of this parameter is byte.
Optimized Mechanism of Delivering Measurement Control Messages for D2F State Transitions
NOTE:
When push to talk (PTT) services are running, this optimization function does not take effect.
The air interface exception-based H2F state transition transits HSDPA users with low throughput
to the CELL_FACH state. Therefore, the resources allocated to these users can be released,
which increases the HSDPA throughput of the cell.
Table 3-3lists the switch parameters related to the air interface exception-based H2F state
transition.
Table 3-3 Switch parameters related to the air interface exception-based H2F state transition
Switch Type Parameter Name Parameter ID
The Downlink Transmitted Code Power measurement configuration is sent to the cell serving the
UEs that meet all of the following conditions, and the NodeB checks the transmitted code power
of the DPCH or F-DPCH for HSDPA users:
A BE service (not IMS service) is set up.
No real-time services are set up, including conversational and streaming services.
The downlink of all PS services is carried on HSDPA channels.
The serving cell is not connected to the DRNC.
When the NodeB reports event Ea related to the downlink transmitted code power of a UE, the
RNC measures the traffic volume and throughput on the UE. If the measured traffic volume is
greater than DlBeAbnH2FHIghTvmThd(BSC6900,BSC6910) and the measured throughput is
less than or equal to DlBeAbnH2FLowThrouThd(BSC6900,BSC6910), the RNC regards the BE
service involved in abnormal data transmission. In this situation, the RNC instructs the UE to
perform an H2F transition to release resources and forbids F2D transitions for the UE within a
certain period of time. The RNC triggers a timer (specified by
BeAbnormH2FStateTransTimer(BSC6900,BSC6910)). The timer stops if the conditions for the
air interface exception-based H2F transition are not met. The RNC instructs the UE to perform an
H2F transition when the timer expires and, at the same time, triggers a penalty timer (specified by
AbnH2FPenaltyLen(BSC6900,BSC6910)) for F2D transitions. F2D transitions are not allowed
for the UE until the timer expires.
If the UE processing the BE service receives event Eb related to the downlink transmitted code
power, the RNC stops measuring the throughput on the UE. In addition, the timer (specified by
BeAbnormH2FStateTransTimer(BSC6900,BSC6910)) stops at the same time if it has started.
3.1.3 D2F State Transition Based on Release of Combined Services
If the proportion of CS+PS combined services is greater than 20% in the network, it is
recommended that you enable D2F state transition based on release of combined services.
Enabling this function can reduce the number of times PS RABs of CS+PS combined services are
released and allow UEs to quickly transfer from the CELL_DCH state to CELL_FACH state,
thereby improving the utilization of cell resources.
When the DRA_PS_STATE_TRANS_WHEN_CS_REL_SWITCH under the
DraSwitch2(BSC6900,BSC6910) parameter is turned on, the PS BE service in CS+PS BE
combined services is processed as follows:
If the PS BE service rate is 0 kbit/s, the PS BE service is not controlled by the timer
ZeroRateUpFailToRelTimerLen(BSC6900,BSC6910). That is, when the timer expires, the
PS service is not released.
NOTE:
ZeroRateUpFailToRelTimerLen(BSC6900,BSC6910) indicates the release timer for the PS BE service at a
rate of 0 kbit/s after the DCCC rate fails to be increased. For details about this parameter, see section 5
"Service Release Policy" in Enhanced Combined Services Feature Parameter Description.
The throughput-based state transition function takes effect only on UEs that meet the following
conditions:
They are in the CELL_DCH state.
They are processing PS BE services.
Their data rates are not 0 kbit/s.
This function can be used in single- or multi-RAB scenarios. After this function is enabled, the
traffic-based state transition function does not take effect. Transferring UEs with low throughput
to the CELL_FACH, CELL_PCH, or URA_PCH state saves network resources and increases
downlink throughput.
The traffic-based state transition function instead of the throughput-based state transition function
takes effect on UEs processing non-PS BE services.
For the throughput-based state transition function, the sliding window is used to measure
throughput. The sliding window size is always the sub measurement period of the throughput-
based D2F/D2P state transition for UEs processing BE services. You can set
BeD2FPThrMeasSubPrd(BSC6900,BSC6910) to specify the sub measurement period.
The average uplink throughput and average downlink throughput during the four sub
measurement periods before each measurement moment are calculated. That is, the throughput
measurement period is always equal to four sub measurement periods.
If both the average uplink throughput and average downlink throughput at the measurement
moment are less than or equal to the low throughput threshold of the throughput-based
D2F/D2P state transition for UEs processing BE services, the timer for triggering the
throughput-based D2F/D2P state transition for UEs processing BE services is started. You
can set the low throughput threshold and the timer by specifying
BeD2FPThrThd(BSC6900,BSC6910) and BeThrD2FPStateTransTmr(BSC6900,BSC6910),
respectively.
The timer for triggering the throughput-based D2F/D2P state transition is stopped if the
uplink or downlink throughput is greater than the value of BeD2FPThrThd at the
measurement moment of a sliding window. If both the average uplink throughput and
average downlink throughput at the measurement moment are less than or equal to the value
of BeD2FPThrThd, layer 2 reports a low throughput indication or an abnormally low
throughput indication based on the measurement results.
After the timer for triggering the throughput-based D2F/D2P state transition expires, layer 2
reports a low throughput indication and determines whether to report an abnormally low
throughput indication based on UE caches.
A UE has abnormally low throughput if the following conditions are met before the state
transition or pending timer expires:
Both the uplink throughput and downlink throughput are less than or equal to the low
throughput threshold at the measurement moment of last four consecutive sliding
windows.
The cache of each UE is greater than 0.
For UEs with abnormally low throughput, after an abnormally low throughput indication is
reported, the pending timer for reporting the low throughput indication to trigger the D2F or
D2P state transitions on UEs with BE services is started. You can set
BeD2FPThrPTAT(BSC6900,BSC6910) to specify the pending timer.
The pending timer is stopped and a high throughput indication is reported if the uplink
or downlink throughput is greater than the value of BeD2FPThrThd at the
measurement moment of a sliding window.
After the pending time expires, layer 2 reports another low throughput indication and
determines whether to report an abnormally low throughput indication based on UE
caches.
For UEs with abnormally low throughput, if the number of low throughput indications or
abnormally low throughput indications is equal to the value of
BeD2FPAbnThrGuardNum(BSC6900,BSC6910), the pending timer continues working. If
the number is less than the value, the pending timer is stopped.
The RNC triggers a corresponding state transition based on the received throughput
indication.
For UEs with low throughput, low throughput indication-based state transitions are
triggered for these UE after the timer expires. If
DRA_THROUGHPUT_BE_D2F_SWITCH under DraSwitch2(BSC6900,BSC6910)
is set to ON, D2F state transitions are triggered. If this switch is set to OFF, D2P state
transitions are triggered.
For UEs with abnormally low throughput, if the number of consecutively received low
throughput indications and abnormally low throughput indications is equal to the value
of BeD2FPAbnThrGuardNum(BSC6900,BSC6910), abnormally low throughput
indication-based D2F state transitions are triggered. After the D2F state transitions
succeed, the F2D penalty timer is started. F2D state transitions are allowed only after
the F2D penalty timer expires, thereby preventing ping-pong state transitions between
CELL_FACH and CELL_DCH and reducing call drops. The F2D penalty timer does
not affect F2D state transitions caused by RAB setups of new CS or PS services.
For UEs with abnormally low throughput, if only the number of low throughput
indications is equal to the value of BeD2FPAbnThrGuardNum(BSC6900,BSC6910),
low throughput indication-based state transitions are triggered. If the number is less
than the value, state transitions are not triggered.
Different F2D penalty timers are started for UEs enabled with RB Parking and UEs not
enabled with RB Parking.
For UEs not enabled with RB Parking, the timer specified by
AbnH2FPenaltyLen(BSC6900,BSC6910) is started.
For UEs enabled with RB Parking, the timer specified by
Parking4ADiscardTimer(BSC6900,BSC6910) is started.
For details about RB Parking, see RB Parking Feature Parameter Description.
The following figure shows the throughput-based D2F/D2P state transition process.
Figure 3-2 Throughput-based D2F/D2P state transition process (for UEs with low throughput)
Figure 3-3 Throughput-based D2F/D2P state transition process (for UEs with abnormally low throughput)
Table 3-4 lists the switch parameters related to the throughput-based D2F/D2P state transition.
Table 3-4 Switch parameters related to the throughput-based D2F/D2P state transition
Parameter ID Parameter Name
With the low activity stare transition function, you can set the LittleRateThd(BSC6900,BSC6910)
parameter to specify the low activity rate for UEs that meet the D2F state transition conditions
but cannot be switched to the CELL_FACH state.
The low activity state transition applies to BE services carried on the DCH. If a UE is in low
mobility and cannot perform state transitions, the UE is switched to the low activity state to save
network resources.
For a BE service carried on the DCH, the RNC reduces the service rate to the low-activity state
threshold LittleRateThd(BSC6900,BSC6910) to save DCH resources if the following conditions
are met:
The UE cannot perform state transitions and can only stay in the CELL_DCH state. For
example, DRA_PS_BE_STATE_TRANS_SWITCH is set to 0.
The total number of uplink and downlink event 4B reports is greater than or equal to the
D2F state transition threshold before the state transition timer expires.
For combined services, the RNC determines whether to enable the low activity state transition
function and reduces the service rate on a per service basis. For example, in the case of BE and
CS combined services, the RNC processes only BE services. In addition, when the uplink and
downlink of a BE service are carried on different channels, the RNC determines whether to
enable the low activity state transition function and reduces the service rate for the uplink and
downlink separately.
The low activity state transition function is disabled when LittleRateThd(BSC6900,BSC6910) is
greater than or equal to UlDcccRateThd(BSC6900,BSC6910) and
DlDcccRateThd(BSC6900,BSC6910).
If LittleRateThd(BSC6900,BSC6910) is too high, a large number of DCH resources are occupied
for a long period of time even when no data is transmitted, which may lead to network
congestion. When LittleRateThd(BSC6900,BSC6910) is too low and a UE starts transmitting data
again, DCCC will increase the service rate of the UE because of low initial throughput even
though a few radio resources are consumed. It is recommended that
LittleRateThd(BSC6900,BSC6910) be set to a small value.
3.3 D2P State Transition
Compared with UEs in the CELL_DCH state, UEs in the CELL_PCH state consume less network
resources. Therefore, when UEs have no data to transmit, the D2P state transition can save
network resources. The D2P state transition can be performed for non-EFD UEs processing BE
services. For details about the state transitions for EFD UEs, see Enhanced Fast Dormancy Feature
Parameter Description.
Before the inactivity timer expires, the RNC triggers an D2P state transition for a UE that is not
transmitting any data if there is no buffered data at the RLC layer.
The inactivity-based D2P state transition is disabled by default. You can enable it by selecting the
DRA_D2P_WHEN_PS_INACT_SWITCH check box under the
DraSwitch2(BSC6900,BSC6910) parameter in the RNC MML command SET
UCORRMALGOSWITCH.
The PS inactivity timer for D2P state transitions is specified by the D2PPsInactTimer parameter in
the SET UUESTATETRANSTIMER command.
If D2PPsInactTimer is set to a small value, UEs in the CELL_DCH state easily switch to the
CELL_PCH state after the data transmission is complete. Later when UEs start to transmit data
again, UE switch to the CELL_FACH state. Under this circumstance, the number of state
transitions increases, the number of reconfiguration messages over the Uu interface increases,
and the probability or duration of FACH congestion may increase. In addition, the number of
UEs in the CELL_DCH state decrease. If D2PPsInactTimer is set to a large value, it is hard for UEs
in the CELL_DCH state to switch to the CELL_PCH state after the data transmission is
complete. The number of UEs in the CELL_DCH state increases as a result, and DCH resources
are wasted.
3.4 F2P State Transition
F2P state transition applies to BE and PTT services. When UEs have no data to transmit, the F2P
state transition is triggered to save network resources.
Table 3-5 lists the switch parameters related to F2P state transition.
Table 3-5 Switch parameters related to F2P state transition
Switch Type Parameter Name Parameter ID
To increase the accuracy for triggering F2P transitions, inactivity-based F2P is introduced. The
RNC performs inactivity-related measurements. If a UE does not receive or transmit any data
during a period specified by the inactivity timer and the RLC buffer is blank, the RNC enables
the UE to transit from the CELL_FACH state to the CELL_PCH state (abbreviated as F2P). After
enabling, this function replaces the F2P based on 4b event.
Inactivity-based F2P increases the accuracy for triggering F2P transitions, and UEs receiving or
transmitting small packets will not experience F2P transitions. This function sets more strict
conditions for triggering F2P transitions and therefore reduces the reconfigurations for F2P2F
transitions (transitions from CELL_FACH to CELL_PCH and then to CELL_FACH again).
Based on the same traffic model, this function reduces signaling messages used for RB
reconfigurations and cell updates and does not significantly affect the distribution of the number
of users in the CELL_FACH and CELL_PCH states.
Inactivity-based F2P is disabled by default. To enable it, run the RNC MML command SET
UCORRMPARA or turn on PerfEnhanceSwitch3(BSC6900,BSC6910):
PERFENH_INACTIVE_F2P_SWITCH. The inactivity-based F2P state transition timer is
specified by the RNC-level parameter InactF2PstateTransTimer(BSC6900,BSC6910) (SET
UUESTATETRANSTIMER) and cell-level parameter
InactF2PStateTransTimer(BSC6900,BSC6910) (ADD/MOD UCELLUESTATETRANS).
3.5 F2U State Transition
F2U state transition applies to BE and PTT services. When the UE does not have data to transmit,
F2U state transition is triggered to save network resources.
The F2U state transition uses the same parameter settings and trigger conditions as the F2P state
transition.
Table 3-7 lists the switch parameters related to F2U state transition.
Table 3-7 Switch parameters related to F2U state transition
Switch Type Parameter Name Parameter ID
P2U state transition applies to BE services. It reduces the number of CELL UPDATE messages
and saves network resources.
Table 3-8 lists the switch parameters related to P2U state transition.
Table 3-8 Switch parameters related to P2U state transition
Switch Type Parameter Name Parameter ID
Before the state transition, the UE is in the CELL_PCH state. During the cell reselection, the UE
sends the CELL UPDATE messages to the RNC. Upon receiving the CELL UPDATE messages,
the RNC starts a timer CellReSelectTimer(BSC6900,BSC6910) and counts the number of CELL
UPDATE messages with the cause value of cell reselection. When the timer expires, the number
of CELL UPDATE messages may be greater than the threshold
CellReSelectCounter(BSC6900,BSC6910). If both conditions are met, the RNC initiates a P2U
transition when the UE sends CELL UPDATE messages again. Then, the UE in the CELL_PCH
state will be transited to the URA_PCH state.
NOTE:
The UE in the CELL_PCH or URA_PCH state cannot receive or send signaling messages. Therefore, the P2U state
transition involves the transient state CELL_FACH, in which necessary signaling interactions are performed over the
FACH.
After returning to the service area, the UE that stays in the URA_PCH state originates a cell
update procedure. If the cell update cause value carried in the CELL UPDATE message is Re-
entered Service Area, the RNC sends a CELL UPDATE CONFIRM message to instruct the UE
to return to the URA_PCH state.
Certain UEs cannot transit from the URA_PCH state to the CELL_PCH state.This reduces the
amount of signaling caused by cell updates and reconfiguration over the air interface.
NOTE:
The UE in the URA_PCH state cannot receive or send signaling messages. Therefore, the U2U state transition
involves the transient state CELL_FACH, in which necessary signaling interactions are performed over the FACH.
This means U2F and F2U state transitions are involved in U2U state transition.
F2D state transition applies to all services except the CS voice service. F2D state transition helps
alleviate FACH congestion in a cell.
Table 3-11 lists the switch parameters related to the F2D state transition.
Table 3-11 Switch parameters related to F2D state transition
Switch Type Parameter Name Parameter ID
Event 4A report is triggered when the uplink or downlink traffic of a UE exceeds the event 4A
threshold and keeps above the threshold for a certain period (event 4A time to trigger). The F2D
state transition is performed when the UTRAN receives an event 4A report. Then, the RNC
determines the service bearing policies for the UE, such as the transport channel (DCH, HS-
DSCH, or E-DCH) and the target rate. If the cell accommodating the UE is overloaded, the RNC
does not allow the UE to perform F2D state transition.
Table 3-12 lists the threshold, time to trigger, and target rate for event 4A and F2D state transition.
Table 3-12 Threshold, time to trigger, and target rate for event 4A and F2D state transition
Service Event 4A Threshold Event 4A Time to Trigger T
Type
UL target rate (
DraSwitch(BSC
HSUPA_DCCC
DL target rate (
DlDcccRateTh
DL target rate (
NOTE:
It is recommended that the cell-level parameter BeF2HTvmThd(BSC6900,BSC6910) be set to a value greater than
the value of BeH2FTvmThd(BSC6900,BSC6910) in the SET UUESTATETRANS command and the value the
cell-level parameter BeH2FTvmThd(BSC6900,BSC6910) in the ADD UCELLUESTATETRANS command. If
the value is less than that of the BeH2FTvmThd(BSC6900,BSC6910) parameter in the SET UUESTATETRANS
command, the RNC automatically selects a larger value as the actual configuration value.
It is recommended that the cell-level parameter BeF2DTvmThd(BSC6910,BSC6900) be set to a value greater than
the value of D2F2PTvmThd(BSC6900,BSC6910) in the SET UUESTATETRANS command and the value the
cell-level parameter D2F2PTvmThd(BSC6900,BSC6910) in the ADD UCELLUESTATETRANS command. If
the value is less than that of the D2F2PTvmThd(BSC6900,BSC6910) parameter in the SET UUESTATETRANS
command, the RNC automatically selects a larger value as the actual configuration value.
This function uses F2D to relieve the FACH congestion. For details about FACH congestion, see
section 4.3 "FACH Congestion Control" in Flow Control Feature Parameter Description.
Table 3-13 lists the switch parameters related to F2D state transition caused by FACH congestion.
Table 3-13 Switch parameters related to F2D state transition caused by FACH congestion
Switch Type Parameter Name Parameter ID
When you find the FACH of a cell is congested, you can manually turn on this function in the
cell to relieve the FACH congestion. When the function of F2D State Transition Caused by
FACH Congestion is activated, the RNC uses the event 4A threshold
BeF2DHTvmThdForFACHCong(BSC6900,BSC6910) in the cell to replace the original RNC-
level event 4A thresholds as follows:
BeF2DTvmThd(BSC6900,BSC6910)
BeF2HTvmThd(BSC6900,BSC6910)
BeF2ETvmThd(BSC6900,BSC6910)
NOTE:
It is recommended that the cell-level event 4A threshold BeF2DHTvmThdForFACHCong(BSC6900,BSC6910)
be set to a value smaller than the original RNC-level event 4A thresholds.
You can enable the wait time-based F2D state transition function when the DTCH mapped onto
the FACH becomes congested (for example, the value of the
VS.FACH.DTCH.CONG.TIME(BSC6900,BSC6910) counter is greater than 3s.) Enabling this
function helps improve user experience if UEs transmit data in the CELL_FACH state.
Table 3-14 lists the switch parameters related to the wait time-based F2D state transition.
Table 3-14 Switch parameters related to the wait time-based F2D state transition
Switch Type Parameter Name Parameter ID
When a UE in the CELL_FACH state is transmitting data, the F2D state transition is triggered
when the following condition is met:
The delay of transmitting RLC service data units (SDUs) is greater than or equal to data
transmission wait time.
The time threshold for the wait time-based F2D state transition is specified by
BasedTimeF2DThd(BSC6900,BSC6910).
After performing the wait time-based F2D state transition, the RNC does not perform the D2F
state transition when the following conditions are met:
The RNC receives the event 4B report within the penalty time specified by
BasedTimeF2DPT(BSC6900,BSC6910).
The traffic volume for event 4B is not 0.
This mechanism helps prevent ping-pong state transitions.
This function is disabled if BasedTimeF2DThd(BSC6900,BSC6910) is set to 0. It is
recommended that you set BasedTimeF2DThd(BSC6900,BSC6910) to a value smaller than
PsInactTmrForFstDrmFach(BSC6900,BSC6910) (inactivity timer for the F2P state transition)
so that the inactive F2P state transition is not triggered before the F2D state transition.
In weak coverage areas, the delay of the RLC SDU is greater than or equal to data transmission
wait time, which easily triggers the wait time-based F2D state transition. The wait time-based
F2D state transition success rate is relatively low in weak coverage areas, which reduces the F2D
state transition success rate. RAN15.0 introduces solutions to the reduced success rate of wait
time-based F2D state transitions in weak coverage areas. If the number of RLC retransmissions is
larger than its threshold, the RNC regards that UEs are located in weak coverage areas. In weak
coverage areas, the wait time-based F2D state transition is not triggered.
The number of RLC retransmissions can be calculated using the following formula:
Number of RLC retransmissions =
ROUNDUP(BasedTimeF2DThd(BSC6900,BSC6910)/TimerPoll(BSC6900,BSC6910) x
BasedTimeF2DRlcRetrNumCoef(BSC6900,BSC6910))
BasedTimeF2DThd(BSC6900,BSC6910) specifies the time threshold for the wait time-
based F2D state transition.
TimerPoll(BSC6900,BSC6910) specifies the timer for the transmitting side of an AM RLC
entity to wait for a response from the peer end after sending the peer end polling RLC
PDUs.
BasedTimeF2DRlcRetrNumCoef(BSC6900,BSC6910) specifies the coefficient of the
number of RLC retransmissions for the wait time-based F2D state transition.
The wait time-based F2D state transition will be restarted after a state transition failure when the
pending timer for the wait time-based F2D state transition expires.
BasedTimeF2DPTAT(BSC6900,BSC6910) specifies the pending timer.
3.9.4 F2D State Transition Based on Web Page Browsing
The service delay of UEs in the CELL_FACH state is greater than that of the UEs in the
CELL_DCH state. Enabling the F2D state transition based on web page browsing function helps
reduce the web page display delay.
After DRA_WEB_FACH_DELAY_OPT_SWITCH is selected, the RNC identifies services of
a UE when the following conditions are true:
The UE enters the CELL_FACH state.
The UE performs PS BE services.
The UE does not use the E-RACH or E-FACH.
If the UE is browsing web pages, the RNC transfers the UE to the CELL_DCH state. During the
F2D state transition, the RLC data transmission is not suspended for the UE.
The RNC considers that the UE is browsing web pages when the following conditions are true:
The downlink data packets are SYN and ACK packets. The source Transmission Control
Protocol (TCP) port is 80 or 8080.
lists the switch parameters related to the F2D state transition based on web page
Table 3-15
browsing.
Table 3-15 Switch parameters related to the F2D state transition based on web page browsing
Switch Parameter Name Parameter ID
Type
Gains provided by this function in the web page display delay can be monitored using drive tests
or Huawei WINS Space. The WINS Space tool is currently unavailable to customers. For details
about this tool, contact Huawei technical support.
3.9.5 Service-based F2D State Transition Enhancement
The service delay of UEs in the CELL_FACH state is greater than that in the CELL_DCH state.
This function enables fast F2D state transitions for HTTPS services and services carried over
specific TCP ports, shortening the service delay.
The RNC transfers a UE to the CELL_DCH state when all the following conditions are true:
The switches DraSwitch2(BSC6900,BSC6910):
DRA_WEB_FACH_DELAY_OPT_SWITCH and RsvSwitch11(BSC6900,BSC6910):
RESERVED_SWITCH_11_BIT29 are both turned on.
The UE enters the CELL_FACH state.
The UE does not use the E-RACH or E-FACH.
The downlink data packets are SYN and ACK packets.
The source TCP port is 443 (indicating HTTPS services) or the port number is the same as
the TCP port number configured for F2D state transitions.
During the F2D state transition, the RLC data transmission is not suspended for the UE.
The following table lists the switch parameters related to the service-based F2D state transition
enhancement function.
Table 3-17 Switch parameters related to the service-based F2D state transition enhancement function
Switch Type Parameter Parameter ID
Name
state
transition
enhancement
function
If user-plane load sharing and node redundancy are enabled in RNC in Pool scenarios, the TCP
port number for F2D state transitions must be specified on all the RNCs.
Gains provided by this function in delay for HTTPS services and services carried over specific
TCP ports can be monitored using drive tests or Huawei WINS Space. The WINS Space tool is
currently unavailable to customers. For detailed operations, contact Huawei technical support.
3.9.6 F2D State Transition Based on TRB Reset
When a UE is in CELL_FACH and the data transmission is abnormal, the UE sends RLC Reset
message to request RNC to reset the RLC. If the reset fails, the RNC releases the RAB
abnormally.
If the function is turned on, the RNC does not release RAB after the failure of RLC reset but try
to put the UE in CELL_DCH. This can reduce the call drops caused by TRB reset of UEs in
CELL_FACH.
Enabling the F2D state transition based on TRB reset reduces the high call drop rate caused by
the downlink traffic radio bearer (TRB) reset of UEs in the CELL_FACH state. After the UE
transitions to the CELL_DCH state, the call drop rate is reduced.
Table 3-18 lists the switch parameters related to the F2D state transition based on TRB reset.
Table 3-18 Switch parameters related to the F2D state transition based on TRB reset
Switch Type Parameter Name Parameter ID
CELL_DCH state for HSDPA services (carried over the HS-DSCH) CELL_DCH state for
HSUPA services (carried over the E-DCH) The D2D state transition allows for switchover
among channels used for H2D, D2H, E2D, and D2E.
The D2D state transition allows for switchover among channels used for H2D, D2H, E2D, and
D2E. For details, see Table 2-1. Figure 3-4 shows how the D2D state transition is implemented. The
D2D state transition does not have switch parameters.
Figure 3-4 D2D state transition
Table 3-19 lists the D2D state transition types and trigger conditions.
Table 3-19 D2D state transition types and trigger conditions
Type Trigger Condition
E2D During a RAB setup, the RAB is carried over the E-DCH but resources
are insufficient.
During a RAB setup, the RAB is carried over the E-DCH but the
coverage is insufficient. For details, see Radio Bearers Feature Parameter
Description.
After an HSUPA RAB setup, coverage-based fallback from the E-DCH
to the DCH is triggered if the radio coverage is poor during HSUPA
data transmission. For details, see Coverage-based Fallback from the E-DCH
to the DCH.
The E-DCH serving cell (the best cell) has changed and either of the
following conditions is met:
The new best cell does not support the E-DCH.
The new best cell has insufficient resources for the E-DCH.
D2E In the preceding E2D scenarios, the RNC switches the UE back to the E-
DCH when any of the following conditions is met:
Periodic attempts are made to reconfigure to the E-DCH. For details,
see the description of technological satisfaction-based inter-frequency
DRD in Directed Retry Decision Feature Parameter Description.
During DCCC data rate adjustment, the target data rate exceeds the
rate bearing threshold for HSUPA (UlBeTraffThsOnHsupa). After an
admission succeeds, the D2E state transition is triggered.
When the uplink coverage recovers, the UE that falls back to the DCH
using the coverage-based fallback from the E-DCH to the DCH
algorithm will be switched back to the E-DCH. For details, see Coverage-
based Switchback from DCH to the E-DCH.
H2D During a RAB setup, the RAB is carried over the HS-DSCH but
resources are insufficient.
The HS-DSCH serving cell (the best cell) has changed and either of
the following conditions is met:
Type Trigger Condition
The new best cell does not support the HS-DSCH. The new best cell
has insufficient resources for the HS-DSCH.
SRB H2D: If a user is in the weak coverage of a cell and the cell load is
light, the downlink SRB falls back from HS-DSCH to DCH. For details,
see HSDPA Feature Parameter Description.
After an H2D channel fallback, an HSDPA service uses the downlink
initial access rate used when HSDPA BE services switch to the DCH.
This downlink initial access rate is specified by the
DlBeH2DInitialRate(BSC6900,BSC6910) parameter.
D2H In the preceding H2D scenarios, the RNC switches the UE back to the
HS-DSCH when any of the following conditions is met:
Periodic attempts are made to reconfigure to the HS-DSCH. For
details, see the description of technological satisfaction-based
inter-frequency DRD in Directed Retry Decision Feature Parameter
Description.
During DCCC data rate adjustment, the target data rate exceeds
the rate bearing threshold for HSDPA (DlBeTraffThsOnHsdpa).
After an admission succeeds, the D2H state transition is triggered.
SRB H2D: If a user is in the good coverage of a cell or in a cell with
heavy load, the downlink SRB comes back from DCH to HS-DSCH. For
details, see HSDPA Feature Parameter Description.
The coverage-based fallback from the E-DCH to the DCH algorithm is introduced to improve
uplink coverage performance of a single UE during HSUPA BE service data transmission.
To enable the E2D function, you can select
DRA_BASE_COVER_BE_E2D_INITSEL_SWITCH and
DRA_BASE_COVER_BE_E2D_SWITCH under the DraSwitch2(BSC6900,BSC6910)
parameter. DRA_BASE_COVER_BE_E2D_INITSEL_SWITCH controls E2D state
transitions of UEs in access mode in areas with weak coverage.
DRA_BASE_COVER_BE_E2D_SWITCH controls E2D state transitions of UEs in connected
mode in areas with weak coverage.
NOTE:
It is recommended that DRA_BASE_COVER_BE_E2D_INITSEL_SWITCH and
DRA_BASE_COVER_BE_E2D_SWITCH be selected together. If
DRA_BASE_COVER_BE_E2D_INITSEL_SWITCH is selected but
DRA_BASE_COVER_BE_E2D_SWITCH is not selected, UEs cannot be reconfigured from the DCH to the E-
DCH after coverage-based E2D state transitions.
If event 6A/6B measurement is used for an E2D switch and a selection of the initial bearer
channel based on Ec/No it recommended that periodical P-CPICH RSCP measurement be used to
replace event 6A/6B measurement. Periodical P-CPICH RSCP measurement allows a UE to
perform both a TTI switch and an E2D switch. In this case, the TTI of the UE can be switched
from 2 ms to 10 ms before the UE performs the E2D switch, thereby increasing UE throughput
and improving user experience. If E2D switch-related parameters are set to recommended values,
the number of 2 ms TTI UEs decreases and the number of R99 UEs experiencing weak coverage
on the uplink increases, thereby significantly reducing the HSDPA call drop rate.
Event 6A/6B Measurement
During HSUPA BE service data transmission, the BE service falls back from the E-DCH to the
DCH when the following conditions are met:
The UE reports event 6A.
The UE does not report 6B event after reporting event 6A.
The UE reports event 4B for all HSUPA BE services.
Other services of the UE also fall back to the DCH.
The formula for calculating the threshold of event 6A/6B is as follows:
Threshold of event 6A/6B = Maximum UE transmit power – Relative threshold of event 6A for
BE service
In this equation:
Maximum UE transmit power is configured by
MaxAllowedUlTxPower(BSC6900,BSC6910).
For the 2 ms TTI, the relative threshold of event 6A for BE service is
BeThd6A1(BSC6900,BSC6910), and that for 10 ms TTI is BeThd6A2(BSC6900,BSC6910).
For the 2 ms TTI, the relative threshold of event 6B for BE service is
BeThd6B1(BSC6900,BSC6910), and that for 10 ms TTI is BeThd6B2(BSC6900,BSC6910).
The threshold of event 4B is E2DThrou4BThd(BSC6900,BSC6910).
A fallback from E-DCH to DCH occurs only in the current cell, which means the inter-frequency
directed retry decision (DRD) is not performed.
If BASE_RSCP_BE_TTI_E2D_RECFG_SWITCH is set to OFF and the switch controlling
coverage-based fallback from the E-DCH to the DCH (DraSwitch2(BSC6900,BSC6910):
DRA_BASE_COVER_BE_E2D_SWITCH) is enabled, the algorithm for coverage-based
dynamic TTI adjustment for a single BE service over HSUPA is automatically disabled. For
details about the algorithm for coverage-based dynamic TTI adjustment of BE services, see
HSUPA TTI Selection Feature Parameter Description.
If severe FACH congestion occurs on a live network, the smart P2D state transition function can
be enabled to directly transit the UE in the connected state with high traffic volume from
CELL_PCH or URA_PCH to CELL_DCH using the CELL UPDATE message. The UE stays in
the CELL_FACH state for a short period to receive signaling. On the UE side, P2D corresponds
to P2F and F2D. On the UTRAN side, P2D is a process when a UE in the CELL_PCH or
URA_PCH state directly transfers to the CELL_DCH state, thereby improving user experience in
the transmission of massive data.
The smart P2D state transition function increases the number of UEs in the CELL_DCH state. If
the traffic volume measurement (TVM)-based P2D state transition function also takes effect,
gains provided by the smart P2D state transition function for resource usage will decrease.
Table 3-20 lists the switch parameters related to the smart P2D state transition.
Table 3-20 Switch parameters related to the smart P2D state transition
Switch Type Parameter Name Parameter ID
NOTE:
DRA_PCH_UE_SMART_P2D_SWITCH under DraSwitch(BSC6900,BSC6910) applies to cell and RNC levels.
If both switches are enabled, cell-level settings prevail.
When the smart P2D state transition is enabled, the RNC records the amount of data a UE
transmits during the interval between when the UE transits from CELL_PCH or URA_PCH to
CELL_FACH or CELL_DCH and when the UE state transits back to CELL_PCH or URA_PCH.
The RNC records the amount of data transmitted by a UE four consecutive times and predicts the
amount of data the UE will transmit subsequently:
If the amount of data transmitted by a UE exceeds the value of
TvmThdForSmartP2D(BSC6900,BSC6910) for four consecutive times, the RNC predicts
that the amount of data transmitted by the UE remains above the value of
TvmThdForSmartP2D(BSC6900,BSC6910) for the fifth time. When the UE subsequently
transmits data in the CELL_PCH or URA_PCH state, the RNC transits the UE to
CELL_DCH to speed up data transmission.
If the amount of data transmitted by a UE four consecutive times is less than or equal to the
value of TvmThdForSmartP2D(BSC6900,BSC6910), the RNC predicts that the UE has a
small amount of data to transmit subsequently. When the UE subsequently transmits data in
the CELL_PCH or URA_PCH state, the RNC transits the UE state to CELL_FACH.
3.11.2 Load- and Ec/No-based P2D State Transition
If a cell is not congested, enabling the load- and Ec/No-based P2D function can directly switch
UEs from the CELL_PCH or URA_PCH state to the CELL_DCH state, thereby improving user
experience in the delay of data transmission. A cell is not congested when both the following
conditions are met:
The downlink non-HSPA power load is in the normal state or lighter state.
The actual uplink service load is in the normal state or lighter state.
For details about the load state of a cell, see section 3.2 "Load-related Measurement Quantities"
in Load Measurement Feature Parameter Description.
Table 3-21 lists the switch parameters related to the load- and Ec/No-based P2D state transition.
Table 3-21 Switch parameters related to the load- and Ec/No-based P2D state transition
Switch Type Parameter Name Parameter ID
When the load- and Ec/No-based P2D state transition is enabled and the RNC receives a CELL
UPDATE message with the uplink data transmission or paging response cause value from a UE,
a state transition from CELL_PCH or URA_PCH to CELL_DCH is triggered only when the
following conditions are met:
The uplink load of a cell is less than or equal to the value of
ActualloadStateForP2D(BSC6900,BSC6910), and the downlink load of this cell is less than
or equal to the value of NonHLoadStateForP2D(BSC6900,BSC6910).
Ec/No is greater than or equal to the value of P2DEcNoThd(BSC6900,BSC6910).
3.12 CPC and EFACH State Transitions
This section describes the new functions of state transitions introduced in HSPA+. Two new
states are introduced in HSPA+: CELL_DCH (CPC) and enhanced CELL_FACH.
The CELL_DCH (CPC) state (CPC for short) corresponds to the CELL_DCH state, with
continuous packet connectivity (CPC) activated.
The enhanced CELL_FACH state (EFACH for short) corresponds to the CELL_FACH
state, with enhanced CELL_FACH operation activated.
Figure 3-5shows how the CPC and EFACH state transitions are implemented. Compared with
CELL_DCH and CELL_FACH states, the following state transitions are introduces in CPC and
EFACH states: CPC2F CPC2EFACH EFACH2CPC EFACH2D D2EFACH F2CPC. For details,
see Table 2-1. For the switch parameters related to the CPC and EFACH state transitions, see
sections 3.1 D2F State Transition and 3.9 F2D State Transition.
The state transition procedures from enhanced CELL_FACH to CELL_PCH in Figure 3-5 are the
same as those from CELL_FACH to CELL_PCH. For details, see 3.4 F2P State Transition.
Figure 3-5 CPC and EFACH state transitions.
As shown in Figure 3-5, CPC2F, D2EFACH, and CPC2EFACH channel switches are triggered by
event 4B, which are similar to those for the D2F state transition. The only difference is that
CPC2F, D2EFACH, and CPC2EFACH have their own state transition timers, as listed in Table 3-
22. For details about other related parameters, see Table 3-1.
parameter BeD2EfachStateTransTimer(BSC6900,BSC6910):
BE service state transition timer (from DCH to E_FACH)
RNC-level parameter
BeH2EFachStateTransTimer(BSC6900,BSC6910), cell-level
parameter BeH2EfachStateTransTimer(BSC6900,BSC6910):
BE service state transition timer (from HS-DSCH to
E_FACH)
RtDH2EFachStateTransTimer(BSC6900,BSC6910): real-time
service state transition timer (from DCH or HSPA to
E_FACH)
F2CPC, EFACH2D, and EFACH2CPC channel switches are triggered by event 4A, which are
similar to those for the F2D state transition.The only difference is that F2CPC, EFACH2D, and
EFACH2CPC have their own event 4A time to trigger and event 4A thresholds, as listed in Table
3-23. For details about other parameters, see Table 3-12.
RtEFach2DHTvmTimeToTrig(BSC6900,BSC6910): RtEFach2DHTvmThd(BSC6900,B
event 4A time to trigger for real-time service state event 4A threshold for real-time s
transition (E_FACH to DCH/HSPA) state transition (E_FACH to DCH
NOTE:
DRA_SMART_FAST_STATE_TRANS_SWITCH under DraSwitch(BSC6900,BSC6910) applies to cell and
RNC levels. If both switches are enabled, cell-level settings prevail.
In cells where UEs are moving at high speeds, the RNC preferentially transits UEs in these cells
to the URA_PCH state. This reduces the following:
Number of CELL UPDATE messages
CPU usage on the SPU
RTWP
Network resource consumption
When the policy of preferentially transiting UEs in cells to the URA_PCH state is used:
The RNC transits the UEs to the URA_PCH state by sending CELL UPDATE CONFIRM
messages after the UEs in the cells send CELL UPDATE messages with the cell reselection,
periodical cell update, or serving cell reentry cause value.
The RNC transits the UEs to the URA_PCH state if the UEs in the cells attempt to transition
from the CELL_FACH or CELL_DCH state to the CELL_PCH or URA_PCH state.
lists the switch parameters related to the policy of preferentially transiting UEs in cells
Table 3-25
to the URA_PCH state.
Table 3-25 Switch parameters related to the policy of preferentially transiting UEs in cells to the
URA_PCH state
Switch Type Parameter Name Parameter ID
The RLC PDU size changes when an UE transitions between the CELL_DCH state and
CELL_FACH state, so RLC entity may be re-established during the state transition. If packets are
transmitting on the RLC layer when RLC entity re-establishment occurs, they will get lost. If the
application layer uses reliable connection such as TCP protocol, TCP will retransmit this part of
packets; but if the application layer uses unreliable connection such as UDP protocol, this part of
packets will get lost. For details about RLC entity re-establishment triggered by RLC PDU size
changes, see 3GPP TS 25.322.
The following operations can be performed for Huawei RNCs to reduce the RLC SDU discarding
possibility during the state transition:
Turn on the RLCSDURETRANSMISSION(BSC6900,BSC6910) switch in the RNC MML
command SET UDPUCFGDATA. Then, the RLC layer will resend the SDU on the
downlink after an RLC entity re-establishment.
Turn on CMP_D2F_RLC_ONESIDE_REBUILD_SWITCH under the
CMPSWITCH(BSC6900,BSC6910) parameter,
CMP_F2D_RLC_ONESIDE_REBUILD_SWITCH under the
CMPSWITCH(BSC6900,BSC6910) parameter in RNC MML command SET
UCORRMALGOSWITCH, to enable one-sided RLC re-establishment. One-sided RLC
entity re-establishment can avoid unnecessary RLC entity re-establishment and packet loss.
If the RLC PDU size on the data receiver or the data transmitter changes, only one-sided
RLC entity needs to be re-established. For details about one-sided RLC entity re-
establishment, see 3GPP TS 25.331.
3.16 Out-of-Service Scenario Optimization
When the RNC sends data to UEs in the CELL_FACH state, the UEs may be in the out-of-
service state. Once a UE detects the out-of-service state, the UE searches for a cell. After finding
a suitable target cell, the UE accesses the network again. When a UE is in the out-of-service state,
the RNC initiates an RRC connection release procedure after failing to exchange data with the
UE. As a result, a call drop occurs.
With the out-of-service scenario optimization function, the RNC can determine whether a UE in
the CELL_FACH state is out of service by identifying timeout causes of the signaling exchange
between the RNC and the UE. The examples of timeout causes are as follows:
The RNC detects an SRB or TRB reset during the measurement control, F2P state transition,
F2U state transition, or F2D state transition of a UE in the CELL_FACH.
The RNC does not receive a response on a CELL UPDTAE CONFIRM message, F2P state
transition, or F2D state transition on time, and the RL is out of synchronization.
After accessing the network, the UE can continue with services, thereby reducing PS call drops.
The out-of-service scenario optimization function is controlled by
FACH_OUTOFSER_OPT_SWITCH under the OptimizationSwitch7(BSC6900,BSC6910)
parameter in the RNC MML command SET URRCTRLSWITCH.
In most cases, if UEs experience call drops due to state transitions, the CN will page the UEs in
idle mode when having data to deliver to the UEs. If both the out-of-service scenario
optimization function and the function of forcibly transiting UEs to the CELL_FACH state upon
D2F state transition failures are enabled, the RNC switches UEs experiencing state transition
failures to the out-of-service state instead of releasing RRC connections. In this case, the number
of PS paging requests sent by the CN to UEs in idle mode decreases. After the CN sends paging
requests, the RNC sends different types of paging messages (for example, PAGING TYPE 1
message for UEs in idle mode and PAGING TYPE 2 message for UEs in the CELL_PCH or
URA_PCH state) to UEs in the out-of-service state at the same time based on the possible
connection states of the UEs. In this way, the probability that the UEs receive paging messages
increases. Therefore, enabling these two functions can increase the CN-side paging success rate
for PS services. However, gains in the CN-side paging success rate for PS services cannot be
quantified.
The function of forcibly transiting UEs to the CELL_FACH state upon D2F state transition
failures is controlled by D2F_ABNORMAL_FORCETOFACH_SWITCH under the
OptimizationSwitch7(BSC6900,BSC6910) parameter. For details, see 5.2 Function of Handling D2F
State Transition Failures.
During H2F state transitions, UEs enter the CELL_FACH state before the RNC configures the
UEs' state as CELL_FACH. As a result, the actual UEs' state is different from the UEs' state
configured on the RNC side for a while (that is, the actual UEs' state is CELL_FACH and the
UEs' state configured on the RNC side is CELL_DCH). In this case, the RNC can properly send
data but the UEs cannot receive the data, which results in invalid data transmission. To solve this
problem, the H2F data transmission optimization function is introduced on the RNC. During H2F
state transition, after sending the H2F RB reconfiguration message, the RNC instructs the NodeB
over the private interface to start real-time CQI reliability detection. Once the NodeB detects
continuous unreliable CQIs, the RNC will delete the buffer data and stop bandwidth allocation in
flow control, as shown in Figure 3-7.
The H2F data transmission optimization function is controlled by
RESERVED_SWITCH_0_BIT10 under the RsvSwitch0(BSC6900,BSC6910) parameter.
Figure 3-7 H2F data transmission before and after optimization
4 State Transition When a UE Is in Connected and Idle Modes
The RRC layer provides signaling connections for UEs and the UTRAN so that the UEs can
interact with the network side. Each CN domain has only one signaling connection.
A UE is in connected mode when a signaling connection is set up, which means there is an RRC
connection between the UE and the UTRAN. The UTRAN can locate the UE's position
according to the CELL_DCH, CELL_FACH, and CELL_PCH states. When an RRC connection
is released or an RRC connection setup fails, the UE returns to the idle mode from the connected
mode.
4.2 Always Online
Figure 4-1 shows the service connection release procedure when a UE is not transmitting data.
Figure 4-1 Service connection release procedure when a UE is not transmitting data
NOTE:
The service connection release request from the PDCP entity may not be processed in time because the associated
processor in the RNC is busy.
For combined CS and PS services, the access or release of PS services may lead to CS call drops.
When always online is enabled, turning on the switch
PS_INACT_NOTREL_FOR_CSPS_SWITCH under the
PROCESSSWITCH3(BSC6900,BSC6910) parameter can reduce the call drop rate of CS services
in combined CS and PS services. After CS services in combined CS and PS services are released,
the remaining PS service or combined PS and PS services are processed as usual.
When the sum of T1 and T2 is less than the time required for state transition, the UE enters idle
mode without performing state transition.
4.3 PCH Blacklist
Huawei provides the PCH blacklist function to address the compatibility issue of certain types of
UEs in CELL_PCH or URA_PCH state. A PCH blacklist consists of type allocation codes
(TACs) of international mobile equipment identities (IMEIs). Operators add TACs of certain UEs
to the PCH blacklist.
The RNC determines whether the TAC of an IMEI carried in the UE-reported Identity Request
message is on the PCH blacklist. To add a TAC of a certain UE to the PCH blacklist, an operator
needs to set the TAC_FUNC(BSC6900,BSC6910) parameter to Compatible_Disposition_for_user
and select PCH_DISABLED_SWITCH of the SpecUserFunctionSwitch(BSC6900,BSC6910)
parameter, and then run the ADD UIMEITAC command to add the TAC to the
TAC(BSC6900,BSC6910) text box.
For UEs to transit from the CELL_DCH or CELL_FACH state to the CELL_PCH or URA_PCH
state, the RNC determines whether the UE's TAC is on the PCH blacklist. If so, the RNC forbids
the state transition for the UE and directly releases the RRC connection with the UE. Blacklisted
UEs are prevented from entering the CELL_PCH or URA_PCH state from other states. The
blacklist function also takes effect on UEs enabled with the CELL_PCH state transition function,
URA_PCH state transition function, or Fast Dormancy feature.
To add a TAC of a certain UE to the URA_PCH blacklist, an operator needs to set the
TAC_FUNC(BSC6900,BSC6910) parameter to Special_User_Enhance and select
SPECUSER_URA_PCH_DISABLED_SWITCH of the
SpecUserFunctionSwitch(BSC6900,BSC6910) parameter, and then run the ADD UIMEITAC
command to add the TAC to the TAC(BSC6900,BSC6910) text box.
When a UE is to transit from the CELL_DCH, CELL_FACH, or CELL_PCH state to the
URA_PCH state, the RNC determines whether the UE's TAC is in the URA_PCH blacklist. If the
UE's TAC is in the URA_PCH blacklist, the RNC forbids the UE to enter the URA_PCH state
and transits the UE to the CELL_PCH state.
Blacklisted UEs are prevented from entering the CELL_PCH or URA_PCH state from other
states. The blacklist function also takes effect on UEs enabled with the CELL_PCH state
transition function, URA_PCH state transition function, or Fast Dormancy feature.
An IMEI consists of 14 decimal digits plus a check digit. It includes 8-digit TAC, 6-digit serial
number (SNR), and 1-digit spare digit.
TAC identifies an authenticated device type.
SNR defines serial number of the UE.
The structure of an IMEI is specified in 3GPP TS 23.003. Following is the composition of an
IMEI:
5.1 Overview
During a state transition, the UE's RRC connection status on the RAN side is unstable. If the state
transition succeeds, the actual RRC connection status of the UE is consistent with the UE's RRC
connection status stored on the RNC side and the UE continues to complete other procedures. If
the state transition fails, the RNC checks the UE state and accordingly performs a state transition
or rollback. If RNC does not check the UE's RRC connection status, the actual RRC connection
status of the UE may be inconsistent with the UE's RRC connection status stored on the RNC
side, which will cause a call drop. In practice, state transitions may fail due to other reasons, such
as resource application failures or abnormal cell updates.
This chapter describes the following causes of state transition failures:
State transition expiry: A D2F/F2D/F2P/F2U state transition is not complete when the
RbRecfgRspTm timer expires.
Signaling radio bearer (SRB) reset on the RNC side: The RNC sends a RADIO BEARER
RECONFIGURATION message in AM mode during an F2D or D2F state transition, which
triggers an SRB reset.
Out-of-synchronization RL: During a D2F state transition, the RNC detects that the uplink
RL is out of synchronization.
RL setup failure: The P2D/U2D state transition fails because the RL setup times out or RL
resource application fails.
Abnormal cell update: After receiving a CELL UPDATE message with the cell reselection
or periodic cell update cause value from a UE in the URA_PCH state, the RNC cannot
initiate a state transition.
5.2 Function of Handling D2F State Transition Failures
Function of Forcibly Transiting UEs to the CELL_FACH State upon D2F State Transition Failures
When an SRB reset, a TRB reset, or expiry occurs during a D2F state transition:
The RNC considers that the D2F state transition succeeds. In this case, the RNC forcibly
transits the UE to the CELL_FACH state and deletes the link carrying the DCH.
After receiving the CELL UPDATE message, the RNC sets the rrc-StateIndicator IE in the
CELL UPDATE CONFIRM message to CELL_FACH so that the CELL_FACH state is
synchronized between the RAN side and the UE side.
This function of forcibly transiting UEs to the CELL_FACH state upon D2F state transition
failures is controlled by D2F_ABNORMAL_FORCETOFACH_SWITCH under the
OptimizationSwitch7(BSC6900,BSC6910) parameter.
NOTE:
It is recommended that the out-of-service scenario optimization function be enabled for UEs in the CELL_FACH
state by selecting FACH_OUTOFSER_OPT_SWITCH under the OptimizationSwitch7(BSC6900,BSC6910)
parameter, thereby minimizing the PS call drop rate. For details, see 3.16 Out-of-Service Scenario Optimization.
Function of Handling D2F State Transition Failures Caused by Expiry (Scenarios in Which Air-
Interface Messages Are Sent in AM Mode During D2F State Transitions)
In most cases, the RNC rolls the UE state back to CELL_DCH on the RNC side when a D2F
state transition expires. After the rollback, the actual RRC connection status of the UE becomes
inconsistent with the UE's RRC connection status stored on the RNC side, which will cause a call
drop.
When a D2F state transition expires, the RNC checks whether it has received an ACK message
from the UE or an RL FAIL message from the NodeBs covering all cells in an active set during
the period from the start of the D2F state transition to the expiry of the RbRecfgRspTm timer.
Upon receiving an ACK message from the UE, the RNC considers that the D2F state
transition succeeds and rolls the UE state back to CELL_FACH on the RNC side. In this
case, the RNC does not need to check whether it has received an RL FAIL message from the
NodeBs covering all cells in an active set. In this case, the function of handling D2F state
transition failures is controlled by D2F_PROCEDURE_OPTIMIZATION_SWITCH
under the OptimizationSwitch3(BSC6900,BSC6910) parameter.
If the RNC does not receive an ACK message from a UE, the RNC needs to check whether
it has received an RL FAIL message from the NodeBs covering all cells in an active set. If it
has received, the RNC considers that the D2F state transition succeeds and rolls the UE state
back to CELL_FACH on the RNC side. In this case, the function of handling D2F state
transition failures is controlled by
D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH under the
OptimizationSwitch3(BSC6900,BSC6910) parameter.
The RNC rolls the UE state back to CELL_DCH on the RNC side when the following
conditions are met:
A state transition expires.
The RNC does not receive an ACK message from a UE or an RL FAIL message from
the NodeBs covering all cells in an active set.
In this case, the function of automatically establishing an RL after a state rollback to
CELL_DCH is controlled by D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH
under the OptimizationSwitch3 parameter.
Function of Handling D2F State Transition Failures Caused by Expiry (Scenarios in Which Air-
Interface Messages Are Sent in UM Mode During D2F State Transitions)
During the period from the start of a D2F state transition to the expiry of the RbRecfgRspTm
timer, the RNC considers that the D2F state transition succeeds and rolls the UE state back to the
CELL_FACH state on the RNC side upon receiving an RL FAIL message from the NodeBs
covering all cells in an active set. This function of handling D2F state transition failures is
controlled by D2F_PROCEDURE_OPTIMIZATION_SWITCH under the OptimizationSwitch3
parameter.
Function of Handling D2F State Transition Failures Caused by SRB Resets Triggered by RADIO
BEARER RECONFIGURATION Messages (Scenarios in Which Air-Interface Messages Are sent in
AM Mode During D2F State Transitions)
During a D2F state transition, the RNC detects an SRB reset, which causes a call drop.
If an SRB reset occurs before the RbRecfgRspTm timer for the D2F state transition expires, the
RNC considers that the D2F state transition succeeds upon receiving an RL FAIL message from
the NodeBs covering all cells in an active set when this timer expires. Then, the RNC rolls the
UE state back to CELL_FACH on the RNC side. This function of handling D2F state transition
failures is controlled by D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH under the
OptimizationSwitch3 parameter.
If an SRB reset occurs before the RbRecfgRspTm timer expires and the RNC does not receive an
RL FAIL message from the NodeBs covering all cells in an active set, the RNC rolls the UE state
back to CELL_DCH on the RNC side when this timer expires. After the state rollback to
CELL_DCH on the RNC side, the RNC determines whether to automatically establish an RL.
The function of automatically establishing an RL after a state rollback to CELL_DCH is
controlled by D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH under the
OptimizationSwitch3 parameter, SRB_RESET_RL_SETUP_SWITCH under the
OptimizationSwitch parameter, and PS_RL_SETUP_SWITCH under the OptimizationSwitch
parameter. For details about call reestablishment of PS services, see Call Reestablishment Feature
Parameter Description.
NOTE:
RRC, RB, and physical channel reconfiguration are triggered by messages over the Uu interface. For details, see
3GPP TS 25.331.
RL establishments are triggered by messages over the Iub interface. For details, see 3GPP TS 25.433.
It is recommended that the function of handling D2F state transition failures be used with the optimized mechanism
of delivering measurement control messages for D2F state transitions together. For details about this mechanism, see
3.1 D2F State Transition.
The RNC checks the RL status during the period from the start of an F2D state transition to the
expiry of the RbRecfgRspTm timer. If the RL status is normal, the RNC considers that the F2D
state transition succeeds and rolls the UE state back to CELL_DCH on the RNC side. This
function of handling F2D state transition failures is controlled by
F2D_PROCEDURE_OPTIMIZATION_SWITCH under the OptimizationSwitch3 parameter.
5.4 Function of Handling F2P/F2U State Transition Failures
If messages are sent in UM mode during F2P/F2U state transitions, UE state inconsistency may
occur between the RNC side and the UE side, which will cause call drops. To prevent call drops,
messages are sent in AM mode. The function of handling F2P/F2U state transition failures is
controlled by F2P_USE_AM_RLC_SWITCH under the
OptimizationSwitch7(BSC6900,BSC6910).
It is recommended that RESERVED_SWITCH_19_BIT13 under
RsvSwitch19(BSC6900,BSC6910) be enabled when F2P/F2U state transitions in AM mode
overlap with a cell update procedure with the cause value of "cell reselection", "re-entering
service area", or "periodic cell update". This action can reduce the PS call drop rate in this
scenario.
NOTE:
If F2P_USE_AM_RLC_SWITCH is set to ON, it is recommended that the formula of calculating the PS drop rate
on the PCH be used. During calculation, the number of abnormal RAB releases caused by F2P/F2U state transitions
must be excluded. If messages are sent in AM mode during F2P/F2U state transitions, call drops may occur during
the F2P/F2U process. It is recommended that the AM mode be enabled together with the solution for handling out-
of-service in CELL_FACH state.
After the RNC triggers a P2D/U2D state transition, a P2F/U2F state transition is triggered instead
of the P2D/U2D state transition in a cell where a UE reports a CELL UPDATE message when
any of the following situations occurs:
The NodeB returns a RADIO LINK SETUP FAILURE message.
The RL setup times out.
The RL resource application fails.
The function of handling P2D/U2D state transition failures is controlled by
P2D_PREPFAIL_OPT_SWITCH under the OptimizationSwitch7(BSC6900,BSC6910)
parameter.
5.6 Function of Handling Abnormal Cell Updates of UEs in the URA_PCH State
After the UE state is reconfigured as URA_PCH, the RNC can deliver a CELL UPDATE
CONFIRM message to inform the UE of the state transition to CELL_PCH upon receiving either
of the following messages from the UE:
CELL UPDATE message containing the cell reselection or periodic cell update cause value
UPLINK SIGNALLING TRANSFER INDICATION message containing the cell
reselection or periodic cell update cause value reported by the DRNC
This function of handling abnormal cell updates of UEs in the URA_PCH state is controlled by
URA_PCH_RESEL_CU_OPT_SWITCH under the
OptimizationSwitch7(BSC6900,BSC6910) parameter.
This section describes the solutions used to optimize overlaps between state transitions and other
procedures, which occur on the live network at a low probability.
Before performing a D2F state transition on the RNC side, the RNC checks whether there is a
connection over the Iu-CS interface. If there is, the RNC does not perform the D2F state
transition. This function of optimizing overlaps between D2F state transitions and CS service
setups is controlled by DRA_D2F_LIMIT_WITH_CS_IU_CON_SWITCH under the
DraSwitch2 parameter.
D2P State Transitions and CS Service Setups
Before performing a D2P state transition on the RNC side, the RNC checks whether there is a
connection over the Iu-CS interface. If there is, the RNC does not trigger the D2P state transition.
If there is not, the RNC triggers the D2P state transition.
If the RNC is performing a D2P state transition on the RNC side when it receives a DOWNLINK
DIRECT TRANSFER message, the RNC buffers the message. This function of optimizing
overlaps between D2P state transitions and CS service setups is controlled by
D2P_DT_MSG_BUFFER_SWITCH under the OptimizationSwitch3(BSC6900,BSC6910)
parameter.
Before performing a F2P state transition on the RNC side, the RNC checks whether there is a
connection over the Iu-CS interface. If there is, the RNC does not perform the F2P state
transition. This function of optimizing overlaps between F2P state transitions and CS service
setups is controlled by PERFENH_F2P_LIMIT_WITH_CS_IU_CON_SWITCH under the
PerfEnhanceSwitch1 parameter.
If the RNC is performing an F2P state transition on the RNC side when it receives a
DOWNLINK DIRECT TRANSFER message, the RNC buffers the message. This function of
optimizing overlaps between F2P state transitions and CS service setups is controlled by
F2P_DT_MSG_BUFFER_SWITCH under the OptimizationSwitch parameter.
When the RNC is performing an F2P/F2U state transition on the RNC side, the RNC considers
that the F2P/F2U state transition succeeds upon receiving either of the following messages:
UPLINK SIGNALLING TRANSFER INDICATION message from the DRNC cell
CELL UPDATE message containing any of the following cause values:
Serving cell reentry
Cell reselection
Periodic cell update
In addition, the RNC will discard subsequent RADIO BEARER RECONFIGURATION
COMPLETE messages. This function of optimizing overlaps between F2P/F2U state transitions
and cell updates is controlled by F2PU_RESELECT_CU_OVERLAP_SWITCH under the
OptimizationSwitch7(BSC6900,BSC6910) parameter.
When the RNC is performing an F2P/F2U state transition on the RNC side, the RNC
reconfigures the UE state as CELL_PCH upon receiving either of the following messages:
CELL UPDATE message containing the uplink data transmission or paging response cause
value
UPLINK SIGNALLING TRANSFER INDICATION message from the DRNC cell
In addition, the RNC will discard subsequent RADIO BEARER RECONFIGURATION
COMPLETE messages. This function of optimizing overlaps between F2P/F2U state transitions
and cell updates is controlled by F2PU_DATATRANS_CU_OVERLAP_SWITCH under the
OptimizationSwitch7(BSC6900,BSC6910) parameter.
F2D State Transitions or Cell Updates of UEs in the CELL_FACH State and Inter-RAT Reselection
After receiving an SRNS CONTEXT REQUEST message from the CN, the RNC processes the
received message and sends an SRNS CONTEXT RESPONSE message to the CN without
waiting for expiration of the ongoing process in either of the following scenarios:
The RNC waits for a response from the UE during F2D-triggered RB reconfiguration or RB
setup.
After receiving a CELL UPDATE message from a UE in the CELL_FACH state, the RNC
sends a CELL UPDATE CONFIRM message to the UE and waits for a response from the
UE.
This function of handling overlaps between F2D state transitions or cell updates of UEs in the
CELL_FACH state and inter-RAT reselection is controlled by
FACH_SRNS_CONTEXT_REQ_OPT_SWITCH under the
OptimizationSwitch8(BSC6900,BSC6910) parameter.
This function prevents call drops in UMTS networks after UEs perform inter-RAT reselection.
After the RNC receives a CELL UPDATE message with the cause value "cell reselection", "UE
Serving cell reentry ", "periodic cell update", or "RLC unrecoverable error" during F2D RB
reconfiguration and setup, the RNC processes the cell update and the RAB setup succeeds if
RB_SETUP_F2D_CU_CROSS_OPT_SWITCH under the
OptimizationSwitch7(BSC6900,BSC6910) parameter is selected; the RNC processes the cell
update but the RAB setup fails if RB_SETUP_F2D_CU_CROSS_OPT_SWITCH under the
OptimizationSwitch7(BSC6900,BSC6910) parameter is not selected. After the RNC receives a
CELL UPDATE message with the cause value "RL out of synchronization", the RNC processes
the cell update and the RAB setup succeeds if
F2D_RBSETUP_CU_OVERLAP_OPT_SWITCH under the
OptimizationSwitch8(BSC6900,BSC6910) parameter is selected; the RNC triggers an abnormal
release process if F2D_RBSETUP_CU_OVERLAP_OPT_SWITCH under the
OptimizationSwitch8(BSC6900,BSC6910) parameter is not selected.
U2F State Transitions and Cell Updates Triggered by Cause Values Other Than Those Triggering
U2F State Transitions
When the RNC performs a cell update, the CELL UPDATE CONFIRM message must contain
the new C-RNTI. This function is controlled by the
FACH_CU_WITH_CRNTI_OPT_SWITCH under the
OptimizationSwitch10(BSC6900,BSC6910) parameter.
During a F2P or F2U state transition, if the RNC receives a cell update message with the
cause value of "RLC unrecoverable error", "Serving cell reentry", or "Periodic cell update"
from the UE in the source cell, the RNC will roll back the UE to the CELL_FACH state to
handle the cell update process.
During a F2D state transition, if the RNC receives a cell update message with a cause value
of "RLC unrecoverable error" from the UE in the source cell, the RNC will roll back the UE
to the CELL_FACH state to handle the cell update process.
The RNC receives a cell update message with a cause value "RLC unrecoverable error"
from the UE in the CELL_FACH state in the source cell.
7 Network Impact
System Capacity
None
Network Performance
The function of optimizing coverage-based E2D and TTI switchover parameters reconfigures the
coverage-based E2D and D2E thresholds for combined CS and PS BE services to achieve a
balance between the service drop rate and the throughput.
7.2 WRFD-01061111 HSDPA State Transition
System Capacity
In HSDPA-capable cells, this feature enables HSDPA UEs with no data transmission for a long
time to transit to the CELL_FACH state, saving system resources and improving system capacity.
Network Performance
This feature saves system resources, improves the RRC connection setup success rate and
increases cell throughput at peak hours.
8 Engineering Guidelines
The CELL_DCH state transition includes channel switching in the CELL_DCH state, such as
H2D, D2H, E2D, and D2E. It recommended that the algorithms of weak-coverage-based E2D for
BE services in access mode and weak-coverage-based E2D for BE services in connected mode be
enabled on networks in which the percentage of RSCP-based weak coverage is greater than 10%.
The purpose is to reconfigure weak-coverage UEs to the DCH to minimize the impact of HSUPA
services on KPIs.
Percentage of RSCP-based weak coverage = (VS.RRC.Access.RSCP.7(BSC6900,BSC6910) +
VS.RRC.Access.RSCP.8(BSC6900,BSC6910) +
VS.RRC.Access.RSCP.9(BSC6900,BSC6910))/(VS.RRC.Access.RSCP.0(BSC6900,BSC6910)
+VS.RRC.Access.RSCP.1(BSC6900,BSC6910) + VS.RRC.Access.RSCP.2(BSC6900,BSC6910) +
VS.RRC.Access.RSCP.3(BSC6900,BSC6910) + VS.RRC.Access.RSCP.4(BSC6900,BSC6910) +
VS.RRC.Access.RSCP.5(BSC6900,BSC6910) + VS.RRC.Access.RSCP.6(BSC6900,BSC6910) +
VS.RRC.Access.RSCP.7(BSC6900,BSC6910) + VS.RRC.Access.RSCP.8(BSC6900,BSC6910) +
VS.RRC.Access.RSCP.9(BSC6900,BSC6910))
8.1.2 Required Information
To observe the impact of weak-coverage-based E2D for BE services in access mode and
weak-coverage-based E2D for BE services in connected mode on network performance,
collect the following information:
HSUPA service drop rate:
HSUPA CALL Drop Rate =
VS.HSUPA.RAB.AbnormRel(BSC6900,BSC6910)/(VS.HSUPA.RAB.AbnormRel(BSC
6900,BSC6910) + VS.HSUPA.RAB.NormRel(BSC6900,BSC6910) +
VS.HSUPA.HHO.E2D.SuccOutIntraFreq(BSC6900,BSC6910) +
VS.HSUPA.HHO.E2D.SuccOutInterFreq(BSC6900,BSC6910) +
VS.HSUPA.E2F.Succ(BSC6900,BSC6910) + VS.HSUPA.E2D.Succ(BSC6900,BSC6910))
HSUPA RAB setup success rate:
HSUPA RAB Assignment Success Rate =
VS.HSUPA.RAB.SuccEstab(BSC6900,BSC6910)/VS.HSUPA.RAB.AttEstab(BSC6900,
BSC6910)
Obtain the values of counters described in the following table to evaluate the gains produced
by coverage-based E2D and D2E state transition.
uplink
RTWP.
8.1.3 Deployment
Requirements
Hardware
None
Other features
None
License
None
Data Preparation
Table 8-1 lists the data to be prepared before activating this feature.
Table 8-1 Data to be prepared before activating coverage-based E2D and D2E state transition
Activation
Activation Observation
The following table lists the counter that indicates whether the function takes effect.
When the counter value is not 0, the algorithms of weak-coverage-based E2D for BE services in
access mode and weak-coverage-based E2D for BE services in connected mode take effect.
Deactivation
//Activation procedure
//Enabling coverage-based E2D in access mode
SET UCORRMALGOSWITCH: DraSwitch2=DRA_BASE_COVER_BE_E2D_INITSEL_SWITCH-1;
//Enabling coverage-based E2D in connected mode
SET UCORRMALGOSWITCH: DraSwitch2=DRA_BASE_COVER_BE_E2D_SWITCH-1;
//Turning on the switch for switching BE services from HSUPA channels to R99
channels in weak coverage areas.
SET UCORRMALGOSWITCH: DraSwitch2=DRA_BASE_COVER_BE_E2D_INITSEL_OPT_SWITCH-1;
//Turning on the switch for increasing or decreasing the DCH data rates of
UEs that are switched from the E-DCH to the DCH due to weak coverage.
SET UCORRMALGOSWITCH: DraSwitch2=DRA_BASE_COVER_E2D_DCCC_SWITCH-1;
//Setting the 6A or 6B thresholds for E2D based on the UE TX power
SET UEDCHTTIRECFG: BeThd6A1=7, BeThd6B1=7, BeThd6A2=8, BeThd6B2=8;
//Setting the coverage-based D2E threshold
SET UDCCC: BaseCoverD2E6AThd=9,BaseCoverD2E6BThd=10,E2DTHROU4BTHD=2;
//Setting the Ec/No decision threshold for coverage-based E2D of BE services
SET UFRC: EcN0ThdForBaseCoverE2D=25;
//Setting the upper and lower threshold for RSCP-based E2D for BE services
SET UCHLQUALITYEVALUATE: BeTTI10msRscpThd=-110, BeTTI10msRscpUpThd=-105;
//Setting the upper and lower threshold for RSCP-based E2D for combined CS
and PS BE services
SET UALGORSVPARA: RsvU32Para36=184550912;
//Deactivation procedure
//Disabling coverage-based E2D in access mode
SET UCORRMALGOSWITCH: DraSwitch2=DRA_BASE_COVER_BE_E2D_INITSEL_SWITCH-0;
//Disabling coverage-based E2D in connected mode
SET UCORRMALGOSWITCH: DraSwitch2=DRA_BASE_COVER_BE_E2D_SWITCH-0;
//Turning off the switch for switching BE services from HSUPA channels to R99
channels in weak coverage areas.
SET UCORRMALGOSWITCH: DraSwitch2=DRA_BASE_COVER_BE_E2D_INITSEL_OPT_SWITCH-0;
//Turning off the switch for increasing or decreasing the DCH data rates of
UEs that are switched from the E-DCH to the DCH due to weak coverage.
SET UCORRMALGOSWITCH: DraSwitch2=DRA_BASE_COVER_E2D_DCCC_SWITCH-0;
The benefits and impacts of this function are observed through the following items:
HSUPA traffic volume and HSUPA user quantity
When this function takes effect, the number of HSUPA UEs decreases in weak coverage
areas, and the HSUPA traffic volume decreases. Therefore, if the values of the following
counters decrease, this function takes effect:
VS.HSUPA.MeanChThroughput.TotalBytes(BSC6900,BSC6910): The HSUPA traffic
volume in a cell is supposed to decrease.
VS.HSUPA.UE.Mean.Cell(BSC6900,BSC6910): The average number of HSUPA UEs in
a cell is supposed to decrease.
VS.CellDCHUEs(BSC6900,BSC6910): The number of CELL_DCH UEs in a cell is
supposed to remain unchanged.
HSUPA RAB setup success rate and HSUPA service drop rate
The coverage-based E2D and D2E function allows UEs in the weak coverage areas to be
switched from HSUPA channels to R99 channels, thereby increasing the HSUPA RAB
setup success rate and decreasing the HSUPA service drop rate.
8.2 CELL_PCH State Transition
There are two types of CELL_PCH state transitions: D2P/F2P and P2F.
If the D2P/F2P and P2F state transitions are enabled, the UTRAN allows the state of low-activity
UEs to be transited between CELL_PCH and CELL_FACH. In this case, UEs do not need to
reestablish RRC connections before transmitting data, thereby reducing signaling and load over
the Uu interface, decreasing service setup delay, and improving user experience. If the D2P/F2P
and P2F state transitions are disabled, UEs must release RRC connections and enter the idle
mode every time they stop transmitting data. When the UEs have data to transmit, they must
reestablish RRC connections. Since the UTRAN can learn which cell the UE is camping on,
D2P/F2P and P2F state transitions ease congestion on the paging channel. It is recommended that
CELL_PCH state transitions be enabled in the following scenarios:
Intelligent terminal or data card penetration rate is greater than 50%.
In this scenario, RRC connections are frequently set up and released and RRC
CONNECTION SETUP/RELEASE messages account for a high proportion of the signaling
over the Uu interface.
The paging channel is congested.
8.2.2 Required Information
Before enabling the CELL_PCH state transition, assess the intelligent terminal or data card
penetration rate on the network and check whether the formula for calculating KPIs after the
CELL_PCH state transition is enabled is used. For details about the formula, see section 8.1.4
Performance Monitoring.
8.2.3 Deployment
Requirements
Hardware
None
Other features
None
License
The licenses for HSDPA State Transition (per Mbps) on the RNC side and HSUPA Function
(per NodeB) on the NodeB side have been activated. For details about how to activate a
license, see License Management Feature Parameter Description.
Other requirements
Some UEs on the live network are incompatible with this function. It is recommended these
UEs be blacklisted when this function is enabled. UEs in the blacklist are not allowed to
enter the CELL_PCH state.
For details about how to blacklist UEs, see Terminal Black List Feature Parameter
Description. Before enabling this function, set TAC_FUNC(BSC6900,BSC6910) to
Special_User_Enhance and select PCH_DISABLED_SWITCH under
SpecUserFunctionSwitch(BSC6900,BSC6910).
Data Preparation
None
Activation
Before activating the CELL_PCH state transition, perform the following operations:
NOTE:
For detailed operations, see section 6.2.3 "Activation" in chapter 6 "Engineering Guidelines" in Enhanced Fast
Dormancy Feature Parameter Description.
NOTE:
Activating the preceding policies can reduce the CS service drop rate but affects user experience of PS services in
combined services. For details about how to guarantee user experience of PS services in combined services when the
CS services are ongoing, see section 11.1.1 "When to Use Bearer Channel Type and Access Rate Control Policy for
PS BE Services During a Setup of Combined Services" in Enhanced Combined Services Feature Parameter
Description.
A UE can directly enter the CELL_FACH or CELL_DCH state. It can enter the CELL_PCH or
URA_PCH state only through the state transition from CELL_FACH or CELL_DCH.
1. Activate the state transition for HSDPA and HSUPA services (recommended if Enhanced
Fast Dormancy feature is disabled):
Run the RNC MML command SET UCORRMALGOSWITCH with the
DRA_PS_BE_STATE_TRANS_SWITCH,
DRA_HSDPA_STATE_TRANS_SWITCH, and
DRA_HSUPA_STATE_TRANS_SWITCH check boxes selected under the Dynamic
Resource Allocation Switch parameter.
2. Perform the following operations to enable the state transition from CELL_FACH to
CELL_PCH:
a. Run the RNC MML SET UUESTATETRANSTIMER. In this step, set BE FACH
or E_FACH to PCH Transition Timer to 5 and Cell Reselection Timer to 180.
(Optional) If BE FACH or E_FACH to PCH Transition Timer needs to be set on
the cell level, run the RNC MML command ADD UCELLUESTATETRANS with
Cell ID specified and BE FACH or E_FACH to PCH Transition Timer set to a
proper value.
b. Run the RNC MML command SET UUESTATETRANS. In this step, set Cell
Reselection Counter Threshold to 9.
c. Run the RNC MML command SET UPSINACTTIMER with PsInactTmrForInt
and PsInactTmrForBac both set to 1800.
(Optional) If the PsInactTmrForInt and PsInactTmrForBac parameters require
cell-level configurations, run the RNC MML command ADD UCELLALTIMER
with Cell ID specified and PsInactTmrForInt and PsInactTmrForBac set to
proper values.
3. NOTE:
4. This feature involves the parameter settings of the state transition from CELL_FACH to CELL_PCH or
URA_PCH. For the parameter settings of other types of state transitions, see DCCC Feature Parameter
Description.
5. For parameter settings related to fast dormancy, see Enhanced Fast Dormancy Feature Parameter Description.
3. (Optional) Blacklist UEs with compatibility issues. Run the RNC MML command ADD
UIMEITAC. In this step, set the TAC_FUNC parameter to Special_User_Enhance, set
the TAC and Description parameters for the UEs with compatibility issues, and select
PCH_DISABLED_SWITCH under the SpecUserFunctionSwitch parameter.
NOTE:
Before enabling the PCH blacklist function, select RNC_PS_QUERY_UE_IMEI_SWITCH under the
PROCESSSWITCH2 parameter in the SET URRCTRLSWITCH command.
Activation Observation
After the state transition from CELL_FACH to CELL_PCH is enabled for a certain period of
time, observe the VS.DCCC.Att.F2P(BSC6900,BSC6910) counter. If the value returned by this
counter increases, the state transition from CELL_FACH to CELL_PCH has taken effect.
To check whether UEs enter the CELL_PCH state, you can check the "rrc-StateIndicator" IE in
the RB RECFG or PH CH RECFG message.
To check whether the PCH blacklist function takes effect, perform the following operations:
When UEs in the CELL_DCH or CELL_FACH state stop transmitting data, check whether the
RNC sends an RRC_RRC_CONN_REL message, instead of the RRC_RB_RECFG message
transmitted during a D2P or F2P state transition. If the RNC sends an RRC_RRC_CONN_REL
message, this function takes effect.
Before being blacklisted, UEs in the CELL_DCH or CELL_FACH state are switched to the
CELL_PCH state when the UEs stop transmitting data. The value of the "RRC State indicator" IE
is CELL_PCH. After being blacklisted, UEs are not switched from the CELL_DCH or
CELL_FACH state to the CELL_PCH state but receive the RRC_RRC_CONN_REL message
from the RNC when stopping transmitting data. In this case, the RRC connections of these UEs
are released.
After the blacklist function takes effect, you can observe the counters in the following table to
check its impacts.
After the blacklist function takes effect, blacklisted UEs are prevented from entering the
CELL_PCH or URA_PCH state. Therefore, the number of UEs in the CELL_PCH or URA_PCH
state under the RNC decreases.
NOTE:
If there are few blacklisted UEs, the values of the VS.CellPCHUEs.RNC(BSC6900,BSC6910) and
VS.UraPCHUEs.RNC(BSC6900,BSC6910) counters basically remain unchanged after the blacklist function takes
effect.
Deactivation
NOTE:
When BE FACH or E_FACH to PCH Transition Timer is set to 65535 (maximum value), it is regarded that the
state transition from FACH or E_FACH to PCH is not performed.
Enabling CELL_PCH state transitions affects paging and air interface signaling.
Paging
Check the counters listed in Table 8-2to assess the effect of CELL_PCH state transitions. The
RNC pages UEs in the CELL_PCH state, within the cell. The average number of type-1
paging messages sent by the cell decreases, and so does the number of paging messages
discarded because of PCH congestion in the cell.
After this feature is enabled, a large number of UEs are switched to the CELL_PCH or
URA_PCH state. As a result, the number of paging attempts in idle mode significantly
decreases, but the original paging failures cannot be eliminated. A possible consequence of
this is that the paging success rate in idle mode decreases. The original paging failures may
be caused by the following: UEs that are dropped from the network or abnormally shut
down Poor coverage Multiple RNCs sharing the same LAC or RAC
Table 8-2 Counters related to paging
Counter Counter Name Description
ID
There are four types of URA_PCH state transitions: F2U, U2F, U2U, and P2U.
If the D2P/F2P, P2F, F2U, U2F, U2U, and P2U state transitions are enabled, the UTRAN allows
the state of low-activity UEs to be transited between CELL_PCH/URA_PCH and CELL_FACH.
In this case, UEs do not need to reestablish RRC connections before transmitting data, thereby
reducing signaling and load over the Uu interface, decreasing service setup delay, and improving
user experience. If the D2P/F2P, P2F, F2U, U2F, U2U, and P2U state transitions are disabled,
UEs must release RRC connections and enter the idle mode every time they stop transmitting
data. When the UEs have data to transmit, they must reestablish RRC connections.
Enabling F2U, U2F, U2U, and P2U state transitions also reduces the number of cell reselections
and thereby reduces air interface signaling caused by CELL UPDATE messages. It is
recommended that URA_PCH state transitions be enabled in scenarios where cell reselections
generate too many CELL UPDATE messages.
After the URA_PCH state transition is enabled, the paging channel may be congested due to a
dramatic increase in paging messages. In this case, divide the UTRAN registration area (URA) or
enable the Layered Paging in URA_PCH feature.
8.3.2 Required Information
URA_PCH state transition is meant to reduce CELL UPDATE messages triggered by cell
reselections. These messages are sent by a UE in the CELL_PCH state after the UE moves to a
new cell. Before enabling URA_PCH state transitions, collect the number of UEs in the
CELL_PCH state and the number of CELL UPDATE messages triggered by cell reselections.
8.3.3 Deployment
Requirements
Hardware
None
Other features
None
License
None
Other requirements
Some UEs on the live network are incompatible with this function. It is recommended these
UEs be blacklisted when this function is enabled. UEs in the blacklist are not allowed to
enter the URA_PCH state.
For details about how to blacklist UEs, see Terminal Black List Feature Parameter
Description. Before enabling this function, set TAC_FUNC(BSC6900,BSC6910) to
Special_User_Enhance and select PCH_DISABLED_SWITCH under
SpecUserFunctionSwitch. Alternatively, set TAC_FUNC(BSC6900,BSC6910) to
Special_User_Enhance and select SPECUSER_URA_PCH_DISABLED_SWITCH
under SpecUserFunctionSwitch(BSC6900,BSC6910).
Data Preparation
None
Activation
Before activating the URA_PCH state transition, perform the following operations: For detailed
operations, see section 6.2.3 "Activation" in chapter 6 "Engineering Guidelines" in Enhanced Fast
Dormancy Feature Parameter Description.
NOTE:
Activating the preceding policies can reduce the CS service drop rate but affects user experience of PS services in
combined services. For details about how to guarantee user experience of PS services in combined services when the
CS services are ongoing, see section 11.1.1 "When to Use Bearer Channel Type and Access Rate Control Policy for
PS BE Services During a Setup of Combined Services" in Enhanced Combined Services Feature Parameter
Description.
A UE can directly enter the CELL_FACH or CELL_DCH state. It can enter the CELL_PCH or
URA_PCH state only through the state transition from CELL_FACH or CELL_DCH.
1. (Optional) If the Enhanced Fast Dormancy feature is disabled, it is recommended that you
perform the following operation to activate the state transition for HSDPA and HSUPA
services:
Run the RNC MML command SET UCORRMALGOSWITCH. In this step, select
DRA_PS_BE_STATE_TRANS_SWITCH,
DRA_HSDPA_STATE_TRANS_SWITCH, and
DRA_HSUPA_STATE_TRANS_SWITCH under the Dynamic Resource Allocation
Switch parameter.
2. Perform the following operations to enable the state transition from CELL_FACH to
URA_PCH:
a. Run the RNC MML command SET UCORRMALGOSWITCH. In this step, select
DRA_PS_BE_STATE_TRANS_SWITCH under the Dynamic Resource
Allocation Switch parameter.
b. Run the RNC MML command SET UCORRMALGOSWITCH to allow UEs to
directly transit from the CELL_FACH state to the URA_PCH state. In this step,
select DRA_F2U_SWITCH under the Dynamic Resource Allocation Switch
parameter.
c. Run the RNC MML SET UUESTATETRANSTIMER. In this step, set BE FACH
or E_FACH to PCH Transition Timer to 5 and Cell Reselection Timer to the
default value.
(Optional) If BE FACH or E_FACH to PCH Transition Timer needs to be set on
the cell level, run the RNC MML command ADD UCELLUESTATETRANS with
Cell ID specified and BE FACH or E_FACH to PCH Transition Timer set to a
proper value.
d. Run the RNC MML command SET UUESTATETRANS. In this step, set Cell
Reselection Counter Threshold to the default value.
NOTE:
This feature involves the parameter settings of the state transition from CELL_FACH to CELL_PCH
or URA_PCH. For the parameter settings of other types of state transitions, see DCCC Feature
Parameter Description.
For the parameter settings related to fast dormancy, see Enhanced Fast Dormancy Feature Parameter
Description.
3. (Optional) Blacklist UEs with compatibility issues. Run the RNC MML command ADD
UIMEITAC. In this step, set the TAC_FUNC parameter to Special_User_Enhance, set
the TAC and Description parameters for the UEs with compatibility issues, and select
PCH_DISABLED_SWITCH under the SpecUserFunctionSwitch parameter.
NOTE:
Before enabling the PCH blacklist function, select RNC_PS_QUERY_UE_IMEI_SWITCH under the
PROCESSSWITCH2 parameter in the SET URRCTRLSWITCH command.
Activation Observation
After the state transition from CELL_FACH to URA_PCH is enabled for a certain period of time,
observe the VS.DCCC.Att.F2U(BSC6900,BSC6910) and VS.DCCC.Succ.F2U(BSC6900,BSC6910)
counters. If the values of these two counters increase, the state transition from CELL_FACH to
URA_PCH has taken effect.
To check whether the PCH blacklist function takes effect, perform the following operations:
When UEs in the CELL_DCH or CELL_FACH state stop transmitting data, check whether the
RNC sends an RRC_RRC_CONN_REL message, instead of the RRC_RB_RECFG message
transmitted during a D2P or F2P state transition. If the RNC sends an RRC_RRC_CONN_REL
message, this function takes effect.
Before being blacklisted, UEs in the CELL_DCH or CELL_FACH state are switched to the
CELL_PCH state when the UEs stop transmitting data. The value of the "RRC State indicator" IE
is CELL_PCH. After being blacklisted, UEs are not switched from the CELL_DCH or
CELL_FACH state to the CELL_PCH state but receive the RRC_RRC_CONN_REL message
from the RNC when stopping transmitting data. In this case, the RRC connections of these UEs
are released.
After the blacklist function takes effect, you can observe the counters in the following table to
check its impacts.
After the blacklist function takes effect, blacklisted UEs are prevented from entering the
CELL_PCH or URA_PCH state. Therefore, the number of UEs in the CELL_PCH or URA_PCH
state under the RNC decreases.
NOTE:
If there are few blacklisted UEs, the values of the VS.CellPCHUEs.RNC(BSC6900,BSC6910) and
VS.UraPCHUEs.RNC(BSC6900,BSC6910) counters basically remain unchanged after the blacklist function takes
effect.
Deactivation
NOTE:
When BE FACH or E_FACH to PCH Transition Timer is set to 65535 (maximum value), it is regarded that the
state transition from FACH or E_FACH to PCH is not performed.
Enabling URA_PCH state transitions affects paging and air interface signaling.
Paging
Check the counters listed in Table 8-4. The RNC pages UEs in the URA_PCH state, within
the URA. Enabling URA_PCH state transitions increases the number of paging messages,
compared with when only CELL_PCH state transitions are enabled.
After this feature is enabled, a large number of UEs are switched to the CELL_PCH or
URA_PCH state. As a result, the number of paging attempts in idle mode significantly
decreases, but the original paging failures cannot be eliminated. A possible consequence of
this is that the paging success rate in idle mode decreases. The original paging failures may
be caused by the following: UEs that are dropped from the network or abnormally shut
down Poor coverage Multiple RNCs sharing the same LAC or RAC
Table 8-4 Counters related to paging
Counter Counter Name Description
ID
8.4.1 Requirements
Hardware
None
Other features
The WRFD-010610 HSDPA Introduction Package feature has been configured before this
feature is activated.
License
This feature is controlled by the license for the WRFD-010611 HSDPA Enhanced Package
feature. For details about this license, see HSDPA Feature Parameter Description.
8.4.2 Data Preparation
None
8.4.3 Activation
Run the RNC MML command SET UCORRMALGOSWITCH. In this step, select
DRA_HSDPA_STATE_TRANS_SWITCH and DRA_PS_BE_STATE_TRANS_SWITCH
under the Dynamic Resource Allocation Switch parameter.
8.4.4 Activation Observation
8.4.5 Deactivation
Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration:
UMTS Radio Global Configuration Express > Connection_Oriented RRM Switch
Configuration > Connection Oriented Algorithm Switches; CME batch modification center:
Modifying RNC Parameters in Batches). In this step, clear DRA_HSDPA_STATE_TRANS_SWITCH
and DRA_PS_BE_STATE_TRANS_SWITCH under the Dynamic Resource Allocation
Switch parameter.
8.4.6 MML Command Examples
NOTE:
If this penetration rate is required, contact Huawei technical support.
Requirements
Data Preparation
Activation
On the RNC LMT, perform the following operations to activate fast state transition:
1. Enable state transitions.
a. Run the following command to enable the state transition for UEs processing PS BE
services, the HSDPA state transition, and the HSUPA state transition:
SET UCORRMALGOSWITCH:
DraSwitch=DRA_HSDPA_STATE_TRANS_SWITCH-
1&DRA_HSUPA_STATE_TRANS_SWITCH-
1&DRA_PS_BE_STATE_TRANS_SWITCH-1;
b. Set the timers for the state transition.
RNC-level parameter configuration
SET UUESTATETRANSTIMER: BeD2FStateTransTimer=5,
BeF2PStateTransTimer=5, BeH2FStateTransTimer=5, BeE2FStateTransTimer=5;
SET UUESTATETRANS: D2FTvmTimeToTrig=D5000,
F2PTvmTimeToTrig=D5000, BeH2FTvmTimeToTrig=D5000;
Cell-level parameter configuration
ADD UCELLUESTATETRANS: CellId=1, BeD2FStateTransTimer=5,
BeF2PStateTransTimer=5, BeH2FStateTransTimer=5, BeE2FStateTransTimer=5;
SET UUESTATETRANS: D2FTvmTimeToTrig=D5000,
F2PTvmTimeToTrig=D5000, BeH2FTvmTimeToTrig=D5000;
c. Prolong the inactivity timer for PS services.
RNC-level parameter configuration
SET UPSINACTTIMER: PsInactTmrForInt=1800, PsInactTmrForBac=1800;
Cell-level parameter configuration
ADD UCELLALTIMER: CellId=1, PsInactTmrForInt=1800,
PsInactTmrForBac=1800;
2. Enable fast state transition.
a. Run the following RNC MML command to enable the RNC-level switch of the smart
fast state transition:
SET UCORRMALGOSWITCH:
DraSwitch=DRA_SMART_FAST_STATE_TRANS_SWITCH-1;
b. Run the following command to enable the cell-level switch of the smart fast state
transition:
ADD UCELLDCCC: CellId=1,
DraSwitch=DRA_SMART_FAST_STATE_TRANS_SWITCH-1;
c. Run the following MML command to set the timer for determining whether a UE is
capable of fast state transition:
SET USTATETIMER: TthdForSFSTUserIdentify=15;
d. Set the inactivity timer for UEs capable of the smart fast state transition in the
CELL_DCH state.
RNC-level parameter configuration
SET UPSINACTTIMER: PsInactTmrForFstDrmDch=5;
Cell-level parameter configuration
ADD UCELLFSTDRMTIMER: CellId=1, PsInactTmrForFstDrmDch=5;
e. Set the inactivity timer for UEs capable of the smart fast state transition in the
CELL_FACH state.
RNC-level parameter configuration
SET UPSINACTTIMER: PsInactTmrForFstDrmFach=5;
Cell-level parameter configuration
ADD UCELLFSTDRMTIMER: CellId=1, PsInactTmrForFstDrmFach=5;
f. Set the inactivity timer for UEs capable of the smart fast state transition in the
CELL_PCH state.
RNC-level parameter configuration
SET UPSINACTTIMER: PsInactTmrForPreFstDrm=1800;
Cell-level parameter configuration
ADD UCELLFSTDRMTIMER: CellId=1, PsInactTmrForPreFstDrm=1800;
Activation Observation
The following procedure is used to monitor the effect of fast state transition:
1. Obtain the IMSI of the UE. Use the UE to start UE tracing and UE throughput monitoring
on the RNC side.
2. Use the UE to set up a service with high traffic volume (for example, browsing a web page
with heavy traffic) and wait until the UE has no data to transmit. Check the UE tracing
results to observe the time when the UE state transits from CELL_DCH to CELL_FACH
and record the time as T1.
3. The data transmission of a UE can be viewed by throughput monitoring. Wait for a period
greater than the value of TthdForSFSTUserIdentify(BSC6900,BSC6910). Set up a service
with high traffic volume again and wait until the UE has no data to transmit. Then, check
the UE tracing results to observe whether the UE state transits from CELL_DCH to
CELL_FACH are within the period specified by
PsInactTmrForFstDrmDch(BSC6900,BSC6910). If they are, record the time when the
state transition is performed as T2, and go to step 4. If they are not, fast state transition
failed.
4. Wait for a period smaller than the value of
TthdForSFSTUserIdentify(BSC6900,BSC6910). Set up a service with high traffic volume
again and wait until the UE has no data to transmit. Then, check the UE tracing results to
observe whether the UE state transits from CELL_DCH to CELL_FACH based on the
timer for state transition are triggered by event 4B. If they are, fast state transition is
functioning properly. If they are not, fast state transition failed.
NOTE:
For parameters related to the 4B event-based D2F state transition, see 3.1 D2F State Transition. For parameters
related to the 4B event-based F2P state transition, see 3.4 F2P State Transition.
Deactivation
On the RNC LMT, perform the following operations to deactivate the smart fast state transition:
1. Run the following command to disable the RNC-level switch of the smart fast state
transition:
SET UCORRMALGOSWITCH:
DraSwitch=DRA_SMART_FAST_STATE_TRANS_SWITCH-0;
2. Run the following command to disable the cell-level switch of the smart fast state
transition:
MOD UCELLDCCC: CellId=1,
DraSwitch=DRA_SMART_FAST_STATE_TRANS_SWITCH-0;
8.5.3 Performance Monitoring
Check the RNC counters in the following table to monitor the gain from fast state transition.
Table 8-8 RNC counters related to fast state transition
Counter ID Counter Name Counter Description
Enabling fast state transition saves DCH resources and therefore affects these counters as
follows: The values of the first six counters decrease. The values of the last three counters may
increase.
If the fast state transition function is also enabled, gains provided by the smart P2D state
transition function for the first six counters in the preceding table will decrease.
8.6 Air Interface Exception-based H2F State Transition
It is recommended that air interface exception-based H2F state transition be enabled for a cell
that meets the following conditions:
The downlink load is high (that is, the proportion of the average TX power to the maximum
TX power is greater than 90%). Proportion of the average TX power to the maximum TX
power = 10(VS.MeanTCP(BSC6900,BSC6910) - MaxTxPower)/10
The proportion of the downlink HSPA power to the maximum TX power is less than 20%.
Proportion of the downlink HSPA power to the maximum TX power = 1-
10(VS.MeanTCP.NonHS(BSC6900,BSC6910) - MaxTxPower)/10
The value of the VS.HSDPA.UE.Mean.Cell(BSC6900,BSC6910) counter measuring the
number of HSDPA UEs is greater than or equal to 40.
The value of the VS.HSDPA.MeanChThroughput(BSC6900,BSC6910) counter measuring
the HSDPA throughput is less than 40 kbit/s.
8.6.2 Deployment
Requirements
Hardware
None
Other features
WRFD-010610 HSDPA Introduction Package
WRFD-01061111 HSDPA State Transition
License
None
Data Preparation
Activation
On the RNC LMT, perform the following operations to activate the air interface exception-based
H2F state transition:
1. Set parameters related to air interface exception-based H2F state transition.
a. Run the following command to set the H2F state transition timer:
SET UUESTATETRANSTIMER: BeAbnormH2FStateTransTimer=31;
b. Run the following command to set the thresholds and penalty time for the H2F state
transition:
SET UUESTATETRANS: DlBeAbnH2FHighThrouThd=8,
DlBeAbnH2FLowThrouThd=8, DlBeAbnH2FHIghTvmThd=102,
DlBeAbnH2FLowTvmThd=102, AbnH2FPenaltyLen=60;
c. Run the following command to set the thresholds for events Ea and Eb used by the
RNC to determine whether the Uu interface transmitting BE services is abnormal:
SET UQUALITYMEAS: DlBeAbnEaThd=2, DlBeAbnEbThd=2;
2. Run the following command to activate the air interface exception-based H2F state
transition function:
ADD UCELLDCCC: CellId=1, BeAbnomH2FSwitch=ON;
Activation Observation
Enabling the air interface exception-based H2F state transition can reduce the number of HSDPA
UEs in a cell, and increase the number of H2F state transition attempts and the number of
successful H2F state transitions.
Table 8-9 Counters used to observe activation of the air interface exception-based H2F state transition
Deactivation
On the RNC LMT, run the following command to deactivate the air interface exception-based
H2F state transition function:
MOD UCELLDCCC: CellId=1, BeAbnomH2FSwitch=OFF;
8.6.3 Performance Monitoring
Check the RNC counters in the following table to monitor the gain from the air interface
exception-based H2F state transition.
Table 8-10 RNC counters related to the air interface exception-based H2F state transition
Counter Counter Name Counter Description
ID
The throughput-based D2F/D2P state transition function can be applied to all networks.
Especially, enabling this function in heavily loaded networks can increase the downlink capacity.
After this function is enabled, two S-CCPCHs are required and the switch restricting the number
of admitted UEs that use FACHs to transmit service data (specified by
FACH_USER_NUM_NOT_CTRL under the NBMCacAlgoSwitch(BSC6900,BSC6910)
parameter) needs to be turned on.
After this function is enabled, the number of state transitions in areas with weak coverage
increases, which may increase the number of PS call drops. In this case, it is recommended that
you turn on the following switches:
Switch controlling whether the RNC identifies the CELL_FACH UEs that are in the out-of-
service state (specified by FACH_OUTOFSER_OPT_SWITCH under the
OptimizationSwitch7(BSC6900,BSC6910) parameter)
Switch controlling whether the RNC commands UEs in the CELL_DCH state to switch to
the CELL_FACH state after these UEs experience D2F state transition failures (specified by
D2F_ABNORMAL_FORCETOFACH_SWITCH under the
OptimizationSwitch7(BSC6900,BSC6910) parameter)
After this function is enabled, the number of UEs in the CELL_FACH state increases, and the
number of CS services initiated by the UEs in the CELL_FACH state accordingly increases. As a
result, the CS access success rate may decrease. In this case, it is recommended that you turn on
the following switches:
Switch controlling whether a PS F2D state transition is prior to a CS service setup in the
CELL_FACH state
Switch controlling whether a cell update can be performed when a UE processing CS
services transfers from the CELL_FACH state to the CELL_DCH state (specified by under
the OptimizationSwitch(BSC6900,BSC6910) parameter).
Switch controlling whether an RB setup is compatible a cell update (specified by
RB_CU_CROSS_COMPATIBLE_SWITCH under the
OptimizationSwitch2(BSC6900,BSC6910) parameter)
Switch controlling whether the RNC sends a RADIO BEARER SETUP message in AM
mode during an F2D state transition (RB_SETUP_F2D_USE_AM_RLC_SWITCH under
the OptimizationSwitch4(BSC6900,BSC6910) parameter)
8.7.2 Deployment
Requirements
Hardware
None
Other features
The state transition for UEs processing BE services, HSDPA State Transition feature, and
HSUPA State Transition feature have been configured before this feature is activated.
License
None
Other requirements
Some UEs on the live network are incompatible with this function. It is recommended these
UEs be blacklisted when this function is enabled. UEs in the blacklist are not allowed to
perform the D2P state transition.
For details about how to blacklist UEs, see Terminal Black List Feature Parameter
Description. Before enabling this function, set TAC_FUNC(BSC6900,BSC6910) to
Special_User_Enhance and select SPECUSER_INHIBIT_D2P_SWITCH under
SpecUserFunctionSwitch3(BSC6900,BSC6910).
Data Preparation
Activation
Activation Observation
Enabling the throughput-based D2F/D2P state transition has the following impacts on a cell:
Reduces the number of UEs in the CELL_DCH state and the number of HSDPA UEs.
Increases the number of UEs in the CELL_FACH or CELL_PCH state. The number of UEs
in the CELL_PCH state is measured by the VS.CellPCHUEs counter.
Increases the value of the VS.HSDPA.H2F.Att counter divided by the value of the
VS.HSDPA.H2F.Succ counter, or the value of the VS.HSDPA.H2P.Att counter divided by
the value of the VS.HSDPA.H2P.Succ counter.
Increases the value of the VS.DCCC.D2C.Att counter divided by the value of the
VS.DCCC.Succ.D2F counter, or the value of the VS.DCCC.D2P.Att counter divided by the
value of the VS.DCCC.D2P.Succ counter.
Table 8-11 Counters related to the throughput-based D2F/D2P state transition
Deactivation
1. On the RNC LMT, run the following command to deactivate the throughput-based state
transition for UEs processing BE services:
SET UCORRMALGOSWITCH:
DraSwitch2=DRA_THROUGHPUT_BE_STATE_TRANS_SWITCH-0;
2. On the RNC LMT, run the following command to deactivate the preferential throughput-
based D2F state transition for UEs processing BE services:
SET UCORRMALGOSWITCH:
DraSwitch2=DRA_THROUGHPUT_BE_D2F_SWITCH-0;
3. On the RNC LMT, run the following command to turn off the switch restricting the number
of admitted UEs that use FACHs to transmit service data:
MOD UCELLALGOSWITCH: CELLID=1,
NBMCacAlgoSwitch=FACH_USER_NUM_NOT_CTRL-0;
4. On the RNC LMT, run the following command to turn off the switch controlling whether
the RNC commands UEs in the CELL_DCH state to switch to the CELL_FACH state after
these UEs experience D2F state transition failures:
SET URRCTRLSWITCH:
OptimizationSwitch7=D2F_ABNORMAL_FORCETOFACH_SWITCH-0;
8.7.3 Performance Monitoring
Enabling this function may change the traffic model. If the traffic model remains unchanged, this
feature will provide gains in throughput. If the traffic model changes, this feature will provide
gains in traffic volume.
Check gains in throughput and traffic volume as follows:
1. You can use counters to evaluate gains in the throughput of a single HSDPA UE and the
throughput of an HSDPA cell. For the throughput of a single HSDPA UE, you can use
either RNC or NodeB counters. However, NodeB counters are recommended.
Throughput of a single HSDPA UE (in the unit of kbit/s) =
VS.HSDPA.MeanChThroughput(BSC6900,BSC6910) (RNC counter)
Throughput of a single HSDPA UE (in the unit of kbit/s) =
VS.HSDPA.DataOutput.Traffic/(VS.HSDPA.DataTtiNum.User x 2) (NodeB counters)
data to transmit
in the queue
buffer
NOTE:
SP indicates a measurement period in the unit of minute. For details about the preceding KPIs and counters, see KPI
Reference and Performance Counter Reference.
8.8.1 When to Use D2F State Transition Based on Release of Combined Services
If the proportion of CS+PS combined services is greater than 20% in the network, it is
recommended that you enable the D2F state transition based on release of combined services.
8.8.2 Deployment
Requirements
Hardware
None
Other features
WRFD-010610 HSDPA Introduction Package
WRFD-01061111 HSDPA State Transition
License
None
This feature is not under license control.
Data Preparation
Dynamic DraSwitch(BSC6900,BSC6910) Select the following check boxes under this parameter: Network
Resource DRA_PS_BE_STATE_TRANS_SWITCH Plan
Allocation DRA_HSDPA_STATE_TRANS_SWITCH
Switch
DRA_HSUPA_STATE_TRANS_SWITCH
Activation
On the RNC LMT, run the following command to activate the D2F state transition based on
release of combined services:
SET UCORRMALGOSWITCH:
DraSwitch2=DRA_PS_STATE_TRANS_WHEN_CS_REL_SWITCH-1;
Activation Observation
The following procedure is used to monitor the effect of the D2F state transition based on release
of combined services:
1. Use a UE to initiate a PS interactive or background service and then a CS service. In this
step, ensure that the rate of the PS service is 0 kbit/s and the CS service lasts for 180s. If the
PS BE service is not released, the function of preventing release of the PS BE service in
combined services takes effect.
2. Release the CS service. If the RNC sends an RRC_RB_RECFG message to transit the UE
to the CELL_FACH state, the function of initiating the fast D2F state transition after
release of the CS service in combined services takes effect.
Deactivation
On the RNC LMT, run the following command to deactivate the D2F state transition based on
release of combined services:
SET UCORRMALGOSWITCH:
DraSwitch2=DRA_PS_STATE_TRANS_WHEN_CS_REL_SWITCH-0;
8.8.3 Performance Monitoring
Check the RNC counters in the following table to monitor the gain provided by the D2F state
transition based on release of combined services.
Table 8-13 RNC counters related to the D2F state transition based on release of combined services
Counter Counter Name Counter Description
ID
If the DTCH mapped onto the FACH becomes congested (for example, the value of the
VS.FACH.DTCH.CONG.TIME(BSC6900,BSC6910) counter is greater than 3s), it is
recommended that you enable the wait time-based F2D state transition to improve user
experience when UEs in the CELL_FACH state are transmitting data.
8.9.2 Deployment
Requirements
Hardware
None
Other features
None
License
None
This feature is not under license control.
Data Preparation
Dynamic DraSwitch(BSC6900,BSC6910) Select the following check boxes under this Network
Resource parameter: Plan
Allocation DRA_PS_BE_STATE_TRANS_SWITCH
Switch DRA_HSDPA_STATE_TRANS_SWITCH
DRA_HSUPA_STATE_TRANS_SWITCH
F2D BasedTimeF2DThd(BSC6900,BSC6910) Set this parameter to a value other than 0. The Network
Threshold recommended value is 28. Plan
Based
Waiting
Time
Activation
On the RNC LMT, run the following command to deactivate the wait time-based F2D state
transition:
SET UUESTATETRANS: BasedTimeF2DThd=28;
Activation Observation
None
Deactivation
On the RNC LMT, run the following command to deactivate the wait time-based F2D state
transition:
SET UUESTATETRANS: BasedTimeF2DThd=0;
8.9.3 Performance Monitoring
Check the RNC counters in the following table to monitor the gain provided by the wait time-
based F2D state transition.
Enabling this function increases the probability of state transitions from CELL_FACH to
CELL_DCH, and therefore the value of the VS.CellFACHUEs(BSC6900,BSC6910) counter in the
preceding table decreases but the values of other counters increase.
8.10 Smart P2D State Transition
Requirements
Before deploying the smart P2D state transition, enable one of the following functions:
CELL_PCH state transition
URA_PCH state transition
Enhanced fast dormancy
Data Preparation
Activation
On the RNC LMT, perform the following operations to activate the smart P2D state transition:
1. Enable state transitions.
a. Run the following command to enable the state transition for UEs processing PS BE
services, the HSDPA state transition, and the HSUPA state transition:
SET UCORRMALGOSWITCH:
DRASWITCH=DRA_HSDPA_STATE_TRANS_SWITCH-
1&DRA_HSUPA_STATE_TRANS_SWITCH-
1&DRA_PS_BE_STATE_TRANS_SWITCH-1;
b. Set the state transition timer.
RNC-level parameter configuration
SET UUESTATETRANSTIMER: BeD2FStateTransTimer=5,
BeF2PStateTransTimer=5, BeH2FStateTransTimer=5, BeE2FStateTransTimer=5;
SET UUESTATETRANS: D2FTvmTimeToTrig=D5000,
F2PTvmTimeToTrig=D5000, BeH2FTvmTimeToTrig=D5000;
Cell-level parameter configuration
ADD UCELLUESTATETRANS: CellId=1, BeD2FStateTransTimer=5,
BeF2PStateTransTimer=5, BeH2FStateTransTimer=5, BeE2FStateTransTimer=5;
SET UUESTATETRANS: D2FTvmTimeToTrig=D5000,
F2PTvmTimeToTrig=D5000, BeH2FTvmTimeToTrig=D5000;
c. Prolong the inactivity timer for PS services.
RNC-level parameter configuration
SET UPSINACTTIMER: PsInactTmrForInt=1800, PsInactTmrForBac=1800;
Cell-level parameter configuration
ADD UCELLALTIMER: CellId=1, PsInactTmrForInt=1800,
PsInactTmrForBac=1800;
2. Enable the smart P2D state transition.
a. Run the following RNC MML command to enable the RNC-level switch of the smart
P2D state transition:
SET UCORRMALGOSWITCH:
DraSwitch=DRA_PCH_UE_SMART_P2D_SWITCH-1;
b. If the smart P2D state transition needs to be enabled only in a specific region, run the
following command to enable the cell-level switch of the smart P2D state transition:
ADD UCELLDCCC: CellId=1,
DraSwitch=DRA_PCH_UE_SMART_P2D_SWITCH-1;
c. Run the following RNC MML command to set the load threshold for the smart P2D
state transition:
SET UUESTATETRANS: TvmThdForSmartP2D= 51;
3. (Optional) If HSDPA UEs are activated in a cell, it is recommended that you run the RNC
MML command SET UCORRMPARA with PERFENH_PSTRAFFIC_P2H_SWITCH
under the Performance Enhancement Switch parameter selected to enable the PS service-
triggered P2H state transition.
Activation Observation
The following procedure is used to monitor the effect of the smart P2D state transition:
1. Obtain the IMSI of the UE. Use the UE to start UE tracing and UE throughput monitoring
on the RNC side.
2. When the UE state transits to CELL_PCH or URA_PCH, use the UE to set up a service
with the traffic volume greater than the value of
TvmThdForSmartP2D(BSC6900,BSC6910), such as, FTP download. After the service is
complete, wait for the UE to transit to the CELL_PCH or URA_PCH state.
3. Repeat step 2 for three times.
4. Wait until the UE state transits to CELL_PCH or URA_PCH. Then, use the UE to set up a
service again. Check the UE tracing results to observe whether the UE state directly transits
from CELL_PCH or URA_PCH to CELL_DCH. If it does, the smart P2D state transition is
functioning properly. If not, the smart P2D state transition fails.
Deactivation
Deactivate the smart P2D state transition on the RNC and cell levels.
Run the following command to deactivate the smart P2D state transition on the RNC level:
SET UCORRMALGOSWITCH: DraSwitch=DRA_PCH_UE_SMART_P2D_SWITCH-0;
Run the following command to deactivate the smart P2D state transition on the cell level:
MOD UCELLDCCC: CellId=01,DraSwitch=DRA_PCH_UE_SMART_P2D_SWITCH-0;
8.10.3 Performance Monitoring
Check the RNC counters in the following table to monitor the gain from the smart P2D state
transition.
Enabling the smart P2D state transition relieves FACH congestion and therefore affects these
counters as follows:
The VS.FACH.DTCH.CONG.TIME(BSC6900,BSC6910) value decreases.
The VS.DCCC.P2D.Succ(BSC6900,BSC6910) and
VS.DCCC.URAP2D.Succ(BSC6900,BSC6910) values increase.
The VS.DCCC.URAP2D.Succ(BSC6900,BSC6910) value changes depending on whether
URA_PCH state transition is enabled. The number of UEs in the CELL_DCH state and the
amount of consumed DCH resources may increase. It is recommended that
PERFENH_PSTRAFFIC_P2H_SWITCH under the
PerfEnhanceSwitch(BSC6900,BSC6910) parameter be selected. In this case, UEs in the
CELL_PCH or URA_PCH state can switch to HSPA channels when initiating PS services,
thereby preventing DCH congestion and abnormal increase in the
VS.HSDPA.D2H.Att(BSC6900,BSC6910) value.
To improve user experience of UEs in the CELL_PCH or URA_PCH state that are to transmit
data, it is recommended that PERFENH_P2D_FAIL_RETRY_SWITCH under the
PerfEnhanceSwitch1(BSC6900,BSC6910) parameter be selected. In this case, a UE is allowed to
perform DRD or channel fallback after P2D state transition admission fails. However, triggering
of a DRD after PERFENH_P2D_FAIL_RETRY_SWITCH is selected depends on the setting
of the P2D DRD function. You can run the SET URRCTRLSWITCH command with
RNC_P2D_DRD_SWITCH under the Optimization Switch parameter selected to enable the
P2D DRD function. For details about this function, see Directed Retry Decision Feature Parameter
Description.
8.11 Load- and Ec/No-based P2D State Transition
To improve user experience in the data transmission delay in a cell that is not congested, it is
recommended that the load- and Ec/No-based P2D function be enabled. A cell is not congested
when both the following conditions are met:
The downlink non-HSPA power load is in the normal state or lighter state.
The actual uplink service load is in the normal state or lighter state.
8.11.2 Deployment
Requirements
Before deploying the load- and Ec/No-based P2D state transition, enable the CELL_PCH state
transition, URA_PCH state transition, or enhanced fast dormancy.
Data Preparation
Table 8-15 Parameters related to the load- and Ec/No-based P2D state transition
Activation
On the RNC LMT, perform the following operations to activate the load- and Ec/No-based P2D
state transition:
1. Enable state transitions.
a. Run the following command to enable the state transition for UEs processing PS BE
services, the HSDPA state transition, and the HSUPA state transition:
SET UCORRMALGOSWITCH:
DraSwitch=DRA_HSDPA_STATE_TRANS_SWITCH-
1&DRA_HSUPA_STATE_TRANS_SWITCH-
1&DRA_PS_BE_STATE_TRANS_SWITCH-1;
b. Set the state transition timer.
RNC-level parameter configuration
SET UUESTATETRANSTIMER: BeD2FStateTransTimer=5,
BeF2PStateTransTimer=5, BeH2FStateTransTimer=5, BeE2FStateTransTimer=5;
SET UUESTATETRANS: D2FTvmTimeToTrig=D5000,
F2PTvmTimeToTrig=D5000, BeH2FTvmTimeToTrig=D5000;
Cell-level parameter configuration
ADD UCELLUESTATETRANS: CellId=1, BeD2FStateTransTimer=5,
BeF2PStateTransTimer=5, BeH2FStateTransTimer=5, BeE2FStateTransTimer=5;
SET UUESTATETRANS: D2FTvmTimeToTrig=D5000,
F2PTvmTimeToTrig=D5000, BeH2FTvmTimeToTrig=D5000;
c. Prolong the inactivity timer for PS services.
RNC-level parameter configuration
SET UPSINACTTIMER: PSINACTTMRFORINT=1800,
PSINACTTMRFORBAC=1800;
Cell-level parameter configuration
ADD UCELLALTIMER: CellId=1, PsInactTmrForInt=1800,
PsInactTmrForBac=1800;
2. Enable the load- and Ec/No-based P2D state transition.
a. Run the following command to enable the load- and Ec/No-based P2D state transition
function:
SET URRCTRLSWITCH: PROCESSSWITCH5=LOAD_BASED_P2D_SWITCH-
1;
b. Run the following commands to set the uplink load thresholds for load- and Ec/No-
based P2D state transitions:
SET UUESTATETRANS: ActualloadStateForP2D=UL_NORMAL_STATE;
SET UUESTATETRANS: NonHLoadStateForP2D=DL_NORMAL_STATE;
c. Run the following command to set the Ec/No threshold for load- and Ec/No-based
P2D state transitions:
SET UFRC: P2DEcNoThd=31;
Activation Observation
After the load- and Ec/No-based P2D state transition is enabled for a period of time, the number
of load- and Ec/No-based P2D state transition attempts and the number of successful load- and
Ec/No-based P2D state transitions will increase. Therefore, if the values of the counters in the
following table increase, the load- and Ec/No-based P2D state transition function has taken
effect.
Counter Name Counter Description
Deactivation
On the RNC LMT, run the following command to deactivate the load- and Ec/No-based P2D
state transition:
SET URRCTRLSWITCH: PROCESSSWITCH5=LOAD_BASED_P2D_SWITCH-0;
8.11.3 Performance Monitoring
Check the RNC counters in the following table to monitor the gain from the load- and Ec/No-
based P2D state transition.
Enabling the load- and Ec/No-based P2D state transition has the following impacts:
The values of the VS.LoadAndEcNoBased.P2D.Att and VS.LoadAndEcNoBased.P2D.Succ
counters will increase if the cell is not congested.
If the values of the VS.DCCC.P2D.Att and VS.DCCC.URAP2D.Att counters increase, the
values of the VS.DCCC.P2D.Succ and VS.DCCC.URAP2D.Succ counters will increase,
and the ratio of successful load- and Ec/No-based P2D state transitions to load- and Ec/No-
based P2D state transition attempts will increase.
The number of UEs in the CELL_DCH state increases, which is indicated by
VS.CellDCHUEs.
8.12 Out-of-Service Scenario Optimization
It is recommended that the out-of-service scenario optimization function be enabled when the
high call drop rate of UEs in the CELL_FACH state, such as a call drop rate of 30%, in a network
cannot be reduced using other optimization methods. After the number of call drops of UEs in the
CELL_FACH state decreases, the UEs will be switched to the DCH if they need to transmit data.
In this case, the number of UEs in the CELL_DCH state that are abnormally released may
increase. To avoid this abnormal release, you can enable the call reestablishment function or the
D2F reconfiguration and reestablishment function.
NOTE:
The D2F reconfiguration and reestablishment function allows the state of more UEs to be reconfigured as
CELL_FACH. If congestion occurs on the DTCH, perform the operations in section "Activating the FACH
Parameter Optimization Strategy" in Enhanced Fast Dormancy Feature Parameter Description.
When UEs are carried on the E-FACH or E-RACH, it is recommended that this function not be
enabled. If this function is enabled in this scenario, UEs that have compatibility issues will
experience call drops.
8.12.2 Deployment
Requirements
Hardware
None
Other features
None
License
None
Data Preparation
Activation
Activation Observation
The following procedure is used to monitor the effect of the out-of-service scenario optimization
function on UEs in the CELL_FACH state:
1. Use a UE to initiate a PS interactive or background service. In this step, ensure that the rate
of the PS service is 0 kbit/s so that the UE is transited to the CELL_FACH state.
2. Move the UE at the cell edge until the UE reports a CELL UPDATE message with the cell
reselection cause value, and ensure that the UE does not respond to the CELL UPDATE
CONFIRM message from the RNC on time. Alternatively, ensure that the UE does not
respond to an F2P/F2D state transition initiated by the RNC on time. In this case, however,
the RNC does not release the UE.
3. Wait until the UE accesses the network again (for example, the UE reports a CELL
UPDATE message with the serving cell reentry cause value). Then, observe whether the
RNC can still process the received message and no call drop occurs. If the RNC can, this
function has taken effect. If the RNC cannot, this function does not work properly.
Deactivation
Check the RNC counters in the following table to monitor the gain from the out-of-service
scenario optimization function.
After the out-of-service scenario optimization function is enabled, the RNC starts the parallel
paging procedure for paging messages if the value of the
VS.RANAP.Paging.Att.ParallelTrans(BSC6900,BSC6910) counter changes from 0 to a value
other than 0. This function will reduce PS call drops caused by procedure overlaps or state
transition failures when UEs in the CELL_FACH state are out of service. The PS call drop rate
can be calculated using the following formulas:
PS Call Drop Ratio (Cell) =
[VS.RAB.AbnormRel.PS(BSC6900,BSC6910)/(VS.RAB.AbnormRel.PS(BSC6900,BSC6910)
+ VS.RAB.NormRel.PS(BSC6900,BSC6910))] x 100%
PS Call Drop Ratio with PCH (Cell) = [(VS.RAB.AbnormRel.PS(BSC6900,BSC6910) -
VS.RAB.AbnormRel.PS.PCH(BSC6900,BSC6910) -
VS.RAB.AbnormRel.PS.D2P(BSC6900,BSC6910) -
VS.RAB.AbnormRel.PS.F2P(BSC6900,BSC6910))/(VS.RAB.AbnormRel.PS(BSC6900,BSC6
910) + VS.RAB.NormRel.PS(BSC6900,BSC6910) -
VS.RAB.AbnormRel.PS.PCH(BSC6900,BSC6910) -
VS.RAB.NormRel.PS.PCH(BSC6900,BSC6910) + VS.DCCC.D2P.Succ(BSC6900,BSC6910) +
VS.DCCC.Succ.F2P(BSC6900,BSC6910) + VS.DCCC.Succ.D2U(BSC6900,BSC6910) +
VS.DCCC.Succ.F2U(BSC6900,BSC6910))] x 100%
8.13 Function of Handling State Transition Failures
8.13.1 When to Use the Function of Handling Abnormal Cell Updates of UEs in the URA_PCH State
If a large number of call drops are caused by state transition failures in the live network, it is
recommended that the function of handling state transition failures be enabled to reduce the PS
call drop rate.
If call drops occur in the live network because the RNC does not process cell updates with the
cell reselection or periodic cell update cause value initiated by UEs in the URA_PCH state, it is
recommended that the function of handling abnormal cell updates of UEs in the URA_PCH state
be enabled.
8.13.2 Deployment
Requirements
When enabling the function of handling state transition failures, you need to turn on the switches
for the following functions:
State transition for UEs processing PS BE services
HSDPA state transition
HSUPA state transition
CELL_FACH state transition
CELL_PCH or URA_PCH state transition
Data Preparation
Table 8-16 Parameters related to the function of handling state transition failures
and D2F_PROCEDURE_OPTIMIZATION_SW
under this parameter.
Activation
Run the RNC MML command SET URRCTRLSWITCH and set the parameters for the
functions of handling state transition failures as follows:
To activate the function of handling D2F state transition failures when the UM mode is
used, select D2F_PROCEDURE_OPTIMIZATION_SWITCH under the Optimization
Switch3 parameter.
To activate the function of handling F2D state transition failures when the UM mode is
used, select F2D_PROCEDURE_OPTIMIZATION_SWITCH under the Optimization
Switch3 parameter.
To activate the function of handling D2F state transition failures when the AM mode is
used, select D2F_PROCEDURE_OPTIMIZATION_SWITCH,
D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH and
AM_D2F_F2D_ResTmr_OPTIMIZATION_SWITCH under the Optimization Switch3
parameter.
To activate the function of handling F2D state transition failures when the AM mode is
used, select F2D_PROCEDURE_OPTIMIZATION_SWITCH and
AM_D2F_F2D_ResTmr_OPTIMIZATION_SWITCH under the Optimization Switch3
parameter.
To activate the function of forcibly transiting UEs to the CELL_FACH state in the case of
D2F state transition failures, select D2F_ABNORMAL_FORCETOFACH_SWITCH
under the Optimization Switch7 parameter.
It is recommended that FACH_OUTOFSER_OPT_SWITCH under the Optimization
Switch7 parameter be selected to enable the out-of service scenario optimization function
for UEs in the CELL_FACH state.
To activate the function of using the AM mode during F2P/F2U state transitions, select
F2P_USE_AM_RLC_SWITCH under the Optimization Switch7 parameter.
To activate the function of optimizing overlaps between F2P state transitions in AM mode
and cell updates, select RESERVED_SWITCH_19_BIT13 under the Reserved Switch 19
parameter.
To activate the function of handling failures in P2D/U2D state transition preparations, select
P2D_PREPFAIL_OPT_SWITCH under the Optimization Switch7 parameter.
To activate the function of handling abnormal cell updates of UEs in the URA_PCH state,
run the RNC MML command SET URRCTRLSWITCH. In this step, select
URA_PCH_RESEL_CU_OPT_SWITCH under the Optimization Switch7 parameter.
NOTE:
When the optimization function of handling D2F state transition failures is enabled, it is good practice to turn on the
SRB reset and RL reestablishment switch during measurement control by running the following command:
SET URRCTRLSWITCH: OptimizationSwitch=MC_RL_RESET_SWITCH-
1&SRB_RESET_RL_SETUP_SWITCH-1&PS_RL_SETUP_SWITCH-1;
This increases the solution gains.
When the F2P or F2U state transition function in AM mode is enabled, it is good practice to enable the solution for
out-of-service in CELL_FACH state to decrease the call drop rate by running the following command:
SET URRCTRLSWITCH: OptimizationSwitch7=FACH_OUTOFSER_OPT_SWITCH-1
//Enabling the function of handling D2F state transition failures when the UM
mode is used
SET URRCTRLSWITCH: OptimizationSwitch3=D2F_PROCEDURE_OPTIMIZATION_SWITCH-1;
//Enabling the function of handling F2D state transition failures when the UM
mode is used
SET URRCTRLSWITCH: OptimizationSwitch3=F2D_PROCEDURE_OPTIMIZATION_SWITCH-1;
//Enabling the function of handling D2F state transition failures when the AM
mode is used
SET URRCTRLSWITCH: OptimizationSwitch3=D2F_PROCEDURE_OPTIMIZATION_SWITCH-
1&D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH-
1&AM_D2F_F2D_ResTmr_OPTIMIZATION_SWITCH-1;
//Enabling the function of handling F2D state transition failures when the AM
mode is used
SET URRCTRLSWITCH: OptimizationSwitch3=F2D_PROCEDURE_OPTIMIZATION_SWITCH-
1&AM_D2F_F2D_ResTmr_OPTIMIZATION_SWITCH-1;
//Enabling the function of forcibly transiting UEs to the CELL_FACH state in
the case of D2F state transition failures
SET URRCTRLSWITCH: OptimizationSwitch7=D2F_ABNORMAL_FORCETOFACH_SWITCH-1;
SET URRCTRLSWITCH: OptimizationSwitch7=FACH_OUTOFSER_OPT_SWITCH-1;
//Enabling the function of using the AM mode during F2P/F2U state transitions
SET URRCTRLSWITCH: OptimizationSwitch7=F2P_USE_AM_RLC_SWITCH-1;
//Enabling the function of optimizing overlaps between F2P state transitions
in AM mode and cell updates
SET UALGORSVPARA: RsvSwitch19=RESERVED_SWITCH_19_BIT13-1;
//Enabling the function of handling failures in P2D/U2D state transition
preparations
SET URRCTRLSWITCH: OptimizationSwitch7=P2D_PREPFAIL_OPT_SWITCH-1;
//Enabling the function of handling abnormal cell updates of UEs in the
URA_PCH state
SET URRCTRLSWITCH: OptimizationSwitch7=URA_PCH_RESEL_CU_OPT_SWITCH-1;
Activation Observation
For details, see sections 8.13.1 When to Use the Function of Handling Abnormal Cell Updates of UEs in the
URA_PCH State and 8.13.3 Performance Monitoring.
Deactivation
Run the RNC MML command SET URRCTRLSWITCH and set the parameters for the
functions of handling state transition failures as follows:
To deactivate the function of handling D2F state transition failures when the UM mode is
used, clear D2F_PROCEDURE_OPTIMIZATION_SWITCH under the Optimization
Switch3 parameter.
To deactivate the function of handling F2D state transition failures when the UM mode is
used, clear F2D_PROCEDURE_OPTIMIZATION_SWITCH under the Optimization
Switch3 parameter.
To deactivate the function of handling D2F state transition failures when the AM mode is
used, clear D2F_PROCEDURE_OPTIMIZATION_SWITCH,
D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH and
AM_D2F_F2D_ResTmr_OPTIMIZATION_SWITCH under the Optimization Switch3
parameter.
To deactivate the function of handling F2D state transition failures when the AM mode is
used, clear F2D_PROCEDURE_OPTIMIZATION_SWITCH and
AM_D2F_F2D_ResTmr_OPTIMIZATION_SWITCH under the Optimization Switch3
parameter.
To deactivate the function of forcibly transiting UEs to the CELL_FACH state in the case of
D2F state transition failures, clear D2F_ABNORMAL_FORCETOFACH_SWITCH
under the Optimization Switch7 parameter.
To deactivate the out-of service scenario optimization function for UEs in the CELL_FACH
state, clear FACH_OUTOFSER_OPT_SWITCH under the Optimization Switch7
parameter.
To deactivate the function of using the AM mode during F2P/F2U state transitions, clear
F2P_USE_AM_RLC_SWITCH under the Optimization Switch7 parameter.
To deactivate the function of optimizing overlaps between F2P state transitions in AM mode
and cell updates, clear RESERVED_SWITCH_19_BIT13 under the Reserved Switch 19
parameter.
To deactivate the function of handling failures in P2D/U2D state transition preparations,
clear P2D_PREPFAIL_OPT_SWITCH under the Optimization Switch7 parameter.
To deactivate the function of handling abnormal cell updates of UEs in the URA_PCH state,
run the RNC MML command SET URRCTRLSWITCH. In this step, clear
URA_PCH_RESEL_CU_OPT_SWITCH under the Optimization Switch7 parameter.
//Disabling the function of handling D2F state transition failures when the
UM mode is used
SET URRCTRLSWITCH: OptimizationSwitch3=D2F_PROCEDURE_OPTIMIZATION_SWITCH-0;
//Disabling the function of handling F2D state transition failures when the
UM mode is used
SET URRCTRLSWITCH: OptimizationSwitch3=F2D_PROCEDURE_OPTIMIZATION_SWITCH-0;
//Disabling the function of handling D2F state transition failures when the
AM mode is used
SET URRCTRLSWITCH: OptimizationSwitch3=D2F_PROCEDURE_OPTIMIZATION_SWITCH-
0&D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH-
0&AM_D2F_F2D_ResTmr_OPTIMIZATION_SWITCH-0;
//Disabling the function of handling F2D state transition failures when the
AM mode is used
SET URRCTRLSWITCH: OptimizationSwitch3=F2D_PROCEDURE_OPTIMIZATION_SWITCH-
0&AM_D2F_F2D_ResTmr_OPTIMIZATION_SWITCH-0;
//Disabling the function of forcibly transiting UEs to the CELL_FACH state in
the case of D2F state transition failures
SET URRCTRLSWITCH: OptimizationSwitch7=D2F_ABNORMAL_FORCETOFACH_SWITCH-0;
SET URRCTRLSWITCH: OptimizationSwitch7=FACH_OUTOFSER_OPT_SWITCH-0;
//Disabling the function of using the AM mode during F2P/F2U state
transitions
SET URRCTRLSWITCH: OptimizationSwitch7=F2P_USE_AM_RLC_SWITCH-0;
//Disabling the function of optimizing overlaps between F2P state transitions
in AM mode and cell updates
SET UALGORSVPARA: RsvSwitch19=RESERVED_SWITCH_19_BIT13-0;
//Disabling the function of handling failures in P2D/U2D state transition
preparations
SET URRCTRLSWITCH: OptimizationSwitch7=P2D_PREPFAIL_OPT_SWITCH-0;
//Disabling the function of handling abnormal cell updates of UEs in the
URA_PCH state
SET URRCTRLSWITCH: OptimizationSwitch7=URA_PCH_RESEL_CU_OPT_SWITCH-0;
The counters described in the following table can be used to monitor the gains produced by the
function of handling state transition failures.
Enabling the function of handling F2D and D2F state transition failures can reduce PS call drops,
thereby reducing PS call drop ratios (including HSDPA call drop rate and HSUPA call drop rate).
PS Call Drop Ratio (Cell) = [VS.RAB.AbnormRel.PS/(VS.RAB.AbnormRel.PS +
VS.RAB.NormRel.PS)] x 100%
PS Call Drop Ratio with PCH (Cell) = [(VS.RAB.AbnormRel.PS -
VS.RAB.AbnormRel.PS.PCH - VS.RAB.AbnormRel.PS.D2P -
VS.RAB.AbnormRel.PS.F2P)/(VS.RAB.AbnormRel.PS + VS.RAB.NormRel.PS -
VS.RAB.AbnormRel.PS.PCH - VS.RAB.NormRel.PS.PCH + VS.DCCC.D2P.Succ +
VS.DCCC.Succ.F2P)] x 100%
HSDPA Call Drop Ratio (Cell) =
[(VS.HSDPA.RAB.AbnormRel)/(VS.HSDPA.RAB.AbnormRel +
VS.HSDPA.RAB.NormRel + VS.HSDPA.H2D.Succ + VS.HSDPA.H2F.Succ +
VS.HSDPA.HHO.H2D.SuccOutIntraFreq + VS.HSDPA.HHO.H2D.SuccOutInterFreq)] x
100%
HSDPA Service Drop Ratio with PCH (Cell) = [(VS.HSDPA.RAB.AbnormRel -
VS.HSDPA.RAB.AbnormRel.H2P)/(VS.HSDPA.RAB.AbnormRel +
VS.HSDPA.RAB.NormRel + VS.HSDPA.HHO.H2D.SuccOutIntraFreq +
VS.HSDPA.HHO.H2D.SuccOutInterFreq + VS.HSDPA.H2D.Succ + VS.HSDPA.H2F.Succ
+ VS.HSDPA.H2P.Succ)] x 100%
HSUPA Call Drop Ratio (Cell) =
[VS.HSUPA.RAB.AbnormRel/(VS.HSUPA.RAB.AbnormRel +
VS.HSUPA.RAB.NormRel + VS.HSUPA.HHO.E2D.SuccOutIntraFreq +
VS.HSUPA.HHO.E2D.SuccOutInterFreq + VS.HSUPA.E2F.Succ +
VS.HSUPA.E2D.Succ)] x 100%
HSUPA Call Drop Ratio with PCH (Cell) = [(VS.HSUPA.RAB.AbnormRel -
VS.HSUPA.RAB.AbnormRel.E2P)/(VS.HSUPA.RAB.AbnormRel +
VS.HSUPA.RAB.NormRel + VS.HSUPA.HHO.E2D.SuccOutIntraFreq +
VS.HSUPA.HHO.E2D.SuccOutInterFreq + VS.HSUPA.E2F.Succ + VS.HSUPA.E2D.Succ
+ VS.HSUPA.E2P.Succ)] x 100%
When call reestablishment is triggered by handling a state transition failure, the value of the
VS.AttRlReEst.PS(BSC6900,BSC6910) counter increases.
When the function of handling failures in state transitions during which RADIO BEARER
RECONFIGURATION messages are sent in AM is enabled, the value of the
VS.RAB.AbnormRel.PS.RF.SRBReset(BSC6900,BSC6910) counter decreases.
After the function of handling D2F state transition failures takes effect, call drops may still occur
after state transitions. These call drops are considered as occurring on the common channel
instead of occurring on the DCH, which increases the value of the
VS.RAB.AbnormRel.PS.CCH(BSC6900,BSC6910) counter. This counter indicates the call drop
rate on the common channel.
8.14 Function of Optimizing Overlaps Between State Transitions and Other Procedures
8.14.1 When to Use the Function of Optimizing Overlaps Between State Transitions and Other Procedures
If a CS service fails to be set up due to an overlap between the CS service setup and a state
transition, it is recommended that the function of optimizing the overlap between state transitions
and CS service setups be enabled.
If a U2F state transition fails due to an overlap between the U2F state transition and a cell update
with a cause value other than those triggering the U2F state transition, it is recommended that the
function of optimizing overlaps between U2F state transitions and cell updates not with cause
values for triggering U2F state transitions be enabled.
If an F2P/F2U state transition fails due to an overlap between the F2P/F2U state transition and a
cell update not with a cause value for triggering the F2P/F2U state transition in the live network,
it is recommended that the function of optimizing overlaps between F2P/F2U state transitions and
cell updates not with cause values for triggering F2P/F2U state transitions be enabled. In
addition, it is recommended that P2D_PREPFAIL_OPT_SWITCH under the
OptimizationSwitch7 parameter be set to ON.
If F2D state transitions or cell updates of UEs in the CELL_FACH state overlap with inter-RAT
reselections and call drops occur because the inter-RAT reselections fail, it is recommended that
you enable the function of handling overlaps between F2D state transitions or cell updates of UEs
in the CELL_FACH state and inter-RAT reselections.
If F2P or F2D state transitions or UEs in the CELL_FACH state overlap with the cell update
process and call drops occur because the CELL UPDATE CONFIRM message does not contain
the new C-RNTI, it is recommended that you enable the Cell Updates of UEs in the
CELL_FACH State with C-RNTI Optimization function
(OptimizationSwitch10:FACH_CU_WITH_CRNTI_OPT_SWITCH).
8.14.2 Deployment
Requirements
When enabling the function of optimizing overlaps between state transitions and CS service
setups or the function of optimizing overlaps between U2F state transitions and cell updates
triggered by cause values other than those triggering U2F state transitions, you need to turn on
the switches for the following functions:
State transition for UEs processing PS BE services
HSDPA state transition
HSUPA state transition
CELL_FACH state transition
CELL_PCH or URA_PCH state transition
Data Preparation
Table 8-17 Parameters related to the function of optimizing overlaps between state transitions and CS
service setups or cell updates
select FACH_SRNS_CONTEXT_REQ_OPT_SWITCH
under this parameter.
Activation
To enable the function of optimizing overlaps between D2F state transitions and CS service
setups, run the RNC MML command SET UCORRMALGOSWITCH. In this step, select
DRA_D2F_LIMIT_WITH_CS_IU_CON_SWITCH under the Dynamic Resource
Allocation Switch 2 parameter.
To enable the function of optimizing overlaps between F2P state transitions and CS service
setups, run the RNC MML command SET UCORRMPARA. In this step, select
PERFENH_F2P_LIMIT_WITH_CS_IU_CON_SWITCH under the Performance
Enhancement Switch 1 parameter.
To enable the function of optimizing overlaps between U2F state transitions and cell
updates, run the RNC MML command SET URRCTRLSWITCH. In this step, select
URA2FACH_OVERLAP_CELLUPT_PROC_SWITCHH under the Optimization
Switch4 parameter.
To enable the function of optimizing overlaps between F2P/F2U state transitions and cell
updates, run the RNC MML command SET URRCTRLSWITCH. In this step, select
F2PU_RESELECT_CU_OVERLAP_SWITCH and
F2PU_DATATRANS_CU_OVERLAP_SWITCH under the Optimization Switch7
parameter.
To enable the function of handling overlaps between F2D state transitions or cell updates of
UEs in the CELL_FACH state and inter-RAT reselections, run the RNC MML command
SET URRCTRLSWITCH. In this step, select
FACH_SRNS_CONTEXT_REQ_OPT_SWITCH under the Optimization Switch8
parameter.
Cell Updates of UEs in the CELL_FACH State with C-RNTI Optimization
To enable this function, run the RNC MML command SET URRCTRLSWITCH with
FACH_CU_WITH_CRNTI_OPT_SWITCH selected under the Optimization Switch10
parameter.
Activation Observation
For details, see sections 8.14.1 When to Use the Function of Optimizing Overlaps Between State Transitions and
Other Procedures and 8.14.3 Performance Monitoring.
Deactivation
To disable the function of optimizing overlaps between D2F state transitions and CS service
setups, run the RNC MML command SET UCORRMALGOSWITCH. In this step, clear
DRA_D2F_LIMIT_WITH_CS_IU_CON_SWITCH under the Dynamic Resource
Allocation Switch 2 parameter.
To disable the function of optimizing overlaps between F2P state transitions and CS service
setups, run the RNC MML command SET UCORRMPARA. In this step, clear
PERFENH_F2P_LIMIT_WITH_CS_IU_CON_SWITCH under the Performance
Enhancement Switch 1 parameter.
To disable the function of optimizing overlaps between U2F state transitions and cell
updates, run the RNC MML command SET URRCTRLSWITCH. In this step, clear
URA2FACH_OVERLAP_CELLUPT_PROC_SWITCH under the Optimization
Switch4 parameter.
To disable the function of optimizing overlaps between F2P/F2U state transitions and cell
updates, run the RNC MML command SET URRCTRLSWITCH. In this step, clear
F2PU_RESELECT_CU_OVERLAP_SWITCH and
F2PU_DATATRANS_CU_OVERLAP_SWITCH under the Optimization Switch7
parameter.
To disable the function of handling overlaps between F2D state transitions or cell updates of
UEs in the CELL_FACH state and inter-RAT reselections, run the RNC MML command
SET URRCTRLSWITCH. In this step, clear
FACH_SRNS_CONTEXT_REQ_OPT_SWITCH under the Optimization Switch8
parameter.
Cell Updates of UEs in the CELL_FACH State with C-RNTI Optimization
To disable this function, run the RNC MML command SET URRCTRLSWITCH with
FACH_CU_WITH_CRNTI_OPT_SWITCH deselected under the Optimization
Switch10 parameter.
The counters in the following table can be used to monitor the gains produced by the function of
optimizing overlaps between state transitions and other procedures.
Enabling the function of optimizing overlaps between state transitions and CS service setups
provides the following benefits:
Reduced number of CS service setup failures caused by state transition failures
Improved user experience in CS services
Increased CS RAB setup success rate
Reduced number of state transitions
The CS RAB setup success rate is calculated using the following formula:
CS RAB Setup Success Ratio (Cell) = [(VS.RAB.SuccEstabCS.Conv(BSC6900,BSC6910) +
VS.RAB.SuccEstabCS.Str(BSC6900,BSC6910))/(VS.RAB.AttEstabCS.Conv(BSC6900,BSC6910)
+ VS.RAB.AttEstabCS.Str(BSC6900,BSC6910))] x 100%
It is recommended that F2P_USE_AM_RLC_SWITCH and
P2D_PREPFAIL_OPT_SWITCH under the OptimizationSwitch7(BSC6900,BSC6910)
parameter be set to ON when the function of optimizing overlaps between F2P/F2U state
transitions and cell updates with any of the following cause values:
Cell reselection
Periodic cell update
Serving cell reentry
Uplink data transmission
Paging response
In this case, PS call drops caused by F2P/F2U state transition failures can be reduced. The PS call
drop rates can be calculated using the following formulas:
PS Call Drop Ratio (Cell) = [VS.RAB.AbnormRel.PS/(VS.RAB.AbnormRel.PS +
VS.RAB.NormRel.PS)] x 100%
PS Call Drop Ratio with PCH (Cell) = [(VS.RAB.AbnormRel.PS -
VS.RAB.AbnormRel.PS.PCH - VS.RAB.AbnormRel.PS.D2P -
VS.RAB.AbnormRel.PS.F2P)/(VS.RAB.AbnormRel.PS + VS.RAB.NormRel.PS -
VS.RAB.AbnormRel.PS.PCH - VS.RAB.NormRel.PS.PCH + VS.DCCC.D2P.Succ +
VS.DCCC.Succ.F2P + VS.DCCC.Succ.D2U + VS.DCCC.Succ.F2U)] x 100%
8.15 H2F Data Transmission Optimization
This feature applies when the throughput of a single HSDPA UE needs to be improved on the
NodeB side and the network load needs to be alleviated when the H2F state transition is enabled
and the RRC state is inconsistent on the UE and RNC side during state transition.
8.15.2 Deployment
Requirements
Before enabling H2F data transmission optimization, turn on the following switches:
DRA_PS_BE_STATE_TRANS_SWITCH and DRA_HSDPA_STATE_TRANS_SWITCH.
Hardware
None
Other Features
WRFD-010610 HSDPA Introduction Package
WRFD-01061111 HSDPA State Transition
License
None
Data Preparation
Activation
Deactivation
This function significantly increases NodeB HSDPA throughput and slightly decreases power
consumption.
Check gains provided by this function as follows:
After this function is enabled, the throughput of a single HSDPA user on the NodeB side
increases by 1% to 8% and HSDPA cell throughput on the NodeB side increases by 0% to
3%.
Formulas for calculating throughput:
Cell throughput on the NodeB side = VS.HSDPA.DataOutput.Traffic/[(VS.DataTtiRatio.Mean -
VS.HSDPA.InactiveDataTtiRatio.Mean) x {SP} x 60] (Unit: kbit/s)
After this function is enabled, if the UE state is different on the UE side and on the RNC
side and the RNC delivers data to the UEs, this function reduces invalid data transmission
and therefore reduces power consumption.
Counter used for performance monitoring: VS.MeanTCP(BSC6900,BSC6910)
After this function is enabled, if a layer higher than the RLC layer delivers data, the
throughput of a single HSDPA user on the RNC side decreases by up to 4% because RLC
user-plane data transmission is suspended. The throughput is measured by the
VS.HSDPA.MeanChThroughput(BSC6900,BSC6910) counter.
Table 8-18 Counters used to monitor the H2F data transmission optimization function
Counter ID Counter Name Counter Description
NOTE:
SP indicates a measurement period in the unit of minute. For details about the preceding KPIs and counters, see KPI
Reference and Performance Counter Reference.
The more scenarios in which the UE state is inconsistent on the UE and network side during H2F, the higher the
feature benefits.
This function applies to networks running HTTPS services or services carried over specific TCP
ports, and the service delay needs to be shortened.
8.16.2 Deployment
Requirements
Before deploying service-based F2D state transition enhancement, enable the F2D state transition
based on web page browsing function.
Hardware
None
License
None
Data Preparation
Activation
Activation Observation
Deactivation
Requirements
Data Preparation
Activation
On the RNC LMT, perform the following operations:
1. Run the following command to enable the H2F-oriented event 4A measurement
optimization function:
SET UCORRMPARA:
PerfEnhanceSwitch6=PERFENH_HSDPA_4AMEAS_OPTIMIZE_SWITCH-1;
Activation Observation
Deactivation
This function improves user experience of web browsing services, reduces the web page E2E
delay by 0.8s to 1.2s, reduces the number of state transitions, increases the number of UEs in the
CELL_DCH state, non-HSPA power consumption, and the number of event 4A measurement
reports.
The following shows the delay reduction:
You can evaluate the reduction in delay by conducting a drive test or using the Huawei WINS
Space tool to perform an offline analysis. The WINS Space tool is currently unavailable to
customers. For detailed operations, contact Huawei technical support engineers.
Counters used to monitor this function
9 Parameters
D2F2PTvmThd BSC69 ADD WRFD- User Experience Meaning: This parameter is used
00 UCELLUESTATETR 180106 Improvement for counter increases by 1 if the traffi
ANS
Lightly Loaded GUI Value Range: D8, D16, D32,
MOD
UCELLUESTATETR Cells Unit: byte
ANS
Actual Value Range: 8, 16, 32, 64
Default Value: D128
Parameter ID NE MML Command Feature Feature Name
ID
D2F2PTvmThd BSC69 ADD WRFD- User Experience Meaning: This parameter is used
10 UCELLUESTATETR 180106 Improvement for counter increases by 1 if the traffi
ANS
Lightly Loaded GUI Value Range: D8, D16, D32,
MOD
UCELLUESTATETR Cells Unit: byte
ANS
Actual Value Range: 8, 16, 32, 64
Default Value: D128
BeH2FTvmThd BSC69 ADD WRFD- User Experience Meaning: This parameter is used
00 UCELLUESTATETR 180106 Improvement for
ANS GUI Value Range: D8, D16, D32,
Lightly Loaded Unit: byte
MOD
UCELLUESTATETR Cells
Actual Value Range: 8, 16, 32, 64
ANS
Default Value: D128
BeH2FTvmThd BSC69 ADD WRFD- User Experience Meaning: This parameter is used
10 UCELLUESTATETR 180106 Improvement for
ANS GUI Value Range: D8, D16, D32,
Lightly Loaded Unit: byte
MOD
UCELLUESTATETR Cells
Actual Value Range: 8, 16, 32, 64
ANS
Default Value: D128
E2FThrouThd BSC69 ADD WRFD- User Experience Meaning: This parameter is used
00 UCELLUESTATETR 180106 Improvement for
ANS GUI Value Range: 0~384
Lightly Loaded Unit: kbit/s
MOD
UCELLUESTATETR Cells
Actual Value Range: 0~384
ANS
Default Value: 8
E2FThrouThd BSC69 ADD WRFD- User Experience Meaning: This parameter is used
10 UCELLUESTATETR 180106 Improvement for
ANS GUI Value Range: 0~384
Lightly Loaded Unit: kbit/s
MOD
UCELLUESTATETR Cells
Actual Value Range: 0~384
ANS
Default Value: 8
BeF2ETvmThd BSC69 ADD WRFD- User Experience Meaning: This parameter specifie
00 UCELLUESTATETR 180106 Improvement for
ANS GUI Value Range: D16, D32, D64
Lightly Loaded Unit: byte
MOD
UCELLUESTATETR Cells
Actual Value Range: 16, 32, 64, 1
ANS
Default Value: D1024
BeF2ETvmThd BSC69 ADD WRFD- User Experience Meaning: This parameter specifie
10 UCELLUESTATETR 180106 Improvement for GUI Value Range: D16, D32, D64
ANS
Lightly Loaded Unit: byte
MOD
UCELLUESTATETR Cells
Actual Value Range: 16, 32, 64, 1
ANS
Default Value: D1024
Parameter ID NE MML Command Feature Feature Name
ID
FastDormancyF2DHTv BSC69 ADD WRFD- User Experience Meaning: Threshold of the uplink
mThd 00 UCELLUESTATETR 180106 Improvement for UEs enabled with the Fast Dorma
ANS
Lightly Loaded GUI Value Range: D16, D32, D64
MOD
UCELLUESTATETR Cells Unit: byte
ANS
Actual Value Range: 16, 32, 64, 1
Default Value: D1024
FastDormancyF2DHTv BSC69 ADD WRFD- User Experience Meaning: Threshold of the uplink
mThd 10 UCELLUESTATETR 180106 Improvement for UEs enabled with the Fast Dorma
ANS
Lightly Loaded GUI Value Range: D16, D32, D64
MOD
UCELLUESTATETR Cells Unit: byte
ANS
Actual Value Range: 16, 32, 64, 1
Default Value: D1024
DRA_BASE_CALL_REESTABLIS
DRA_RRC_FACH_NODEB_UNA
DRA_BE_LITTLE_RATE_THD_S
DRA_BE_INIT_BIT_RATE_TYPE
DRA_SRB_HRETRY_AFTER_RB
DRA_PCH_L2_MC_REL_SWITC
DRA_BASE_COVER_UlR99_CQ
DRA_EFACH_D2P_DISABLE_SW
DRA_WEB_EFACH_DELAY_OP
DRA_CELL_DCCC_MC_THD_SW
DRA_SERVICE_BASED_FAST_
Default Value: DRA_BASE_COVE
DRA_D2F_OVER_IUR_SWITCH
DRA_WEB_FACH_DELAY_OPT
DRA_BASE_COVER_LOAD_SR
DRA_RRC_FACH_NODEB_UNA
DRA_PCH_L2_MC_REL_SWITC
DRA_SERVICE_BASED_FAST_
22. DRA_PCH_L2_MC_REL_SW
released after a D2P/F2P state tra
23. DRA_BASE_COVER_UlR99_
1: When this switch is turned on,
DC/3C/4C/DB/MIMO.
0: When this switch is turned off,
coverage is considered weak. If R
If Ec/N0 is less than or equal to th
The function provided by this para
24. DRA_EFACH_D2P_DISABLE
1: This switch is turned on. The D
0: This switch is turned off. The D
25. DRA_WEB_EFACH_DELAY_
1: This switch is turned on. The w
Data transmission is supported du
0: This switch is turned off. The w
26. DRA_CELL_DCCC_MC_THD
1: This switch is turned on. Cell-le
0: This switch is turned off. RNC-l
of PS DCH channels is considere
27. DRA_SERVICE_BASED_FAS
1: This switch is turned on. When
services through the TCP port 44
0: This switch is turned off. The e
GUI Value Range: DRA_BASE_C
DRA_D2F_OVER_IUR_SWITCH
DRA_WEB_FACH_DELAY_OPT
DRA_THROUGHPUT_BE_STAT
DRA_BE_LITTLE_RATE_THD_S
DRA_EFACH_D2P_DISABLE_SW
Unit: None
Actual Value Range:
DRA_BASE_COVER_BE_E2D_I
DRA_PCPICH_ECN0_ON_RACH
DRA_BASE_COVER_BE_E2D_I
DRA_BASE_COVER_BE_E2D_S
DRA_D2F_OVER_IUR_SWITCH
DRA_CSPS_0K_RATE_UP_SWI
DRA_CSPS_BOTH_ULDL_RATE
DRA_PS_STATE_TRANS_WHEN
DRA_BASE_COVER_E2D_DCC
Parameter ID NE MML Command Feature Feature Name
ID
DRA_WEB_FACH_DELAY_OPT
DRA_D2F_LIMIT_WITH_CS_IU_
DRA_D2P_WHEN_PS_INACT_S
DRA_INTELL_STATE_TRANS_O
DRA_BASE_COVER_LOAD_SR
DRA_THROUGHPUT_BE_STAT
DRA_THROUGHPUT_BE_D2F_S
DRA_BASE_CALL_REESTABLIS
DRA_RRC_FACH_NODEB_UNA
DRA_BE_LITTLE_RATE_THD_S
DRA_BE_INIT_BIT_RATE_TYPE
DRA_SRB_HRETRY_AFTER_RB
DRA_PCH_L2_MC_REL_SWITC
DRA_BASE_COVER_UlR99_CQ
DRA_EFACH_D2P_DISABLE_SW
DRA_WEB_EFACH_DELAY_OP
DRA_CELL_DCCC_MC_THD_SW
DRA_SERVICE_BASED_FAST_
Default Value: DRA_BASE_COVE
DRA_D2F_OVER_IUR_SWITCH
DRA_WEB_FACH_DELAY_OPT
DRA_BASE_COVER_LOAD_SR
DRA_RRC_FACH_NODEB_UNA
DRA_PCH_L2_MC_REL_SWITC
DRA_SERVICE_BASED_FAST_
SPECUSER_NONSPT_F2D_SRB
SPECUSER_SEND_CTFC_WHE
SPECUSER_NONSPT_D2F_F2D
SPECUSER_URA_PCH_DISABL
INTERHO_DISABLED_SWITCH,
INTRATHO_DISABLED_SWITCH
Default Value:
SPECUSER_AMR_HOENHANCE
SER_SRB_COVSEL_SWITCH:0,
BLED_SWITCH:0,INTERHO_DIS
RL_PROCEDURE_OPT_SWITCH
FACH_IUR_CU_CELL_RES_ALO
RAB_FAST_RB_SETUP_ACTCF
EFD_D2P_SEND_PAGING_OPT
SRB_OVER_HSPA_OPT_BASED
HO_SS_USER_IDENTIFY_SWIT
RRC_REJ_TNLFAIL_CNT_SWIT
FIX_PFM_SYSOUT_FAIL_SWITC
Default Value:
SECU_CU_CROSS_IP_OPT_SW
ABLED_USE_EFD_SWITCH:0,C
_SWITCH:0,RAB_FAST_RB_SET
CH:0,FIX_PFM_SYSOUT_FAIL_
12)RAB_FAST_RB_SETUP_ACT
Whether the RNC detects private
1: Indicates that this switch is set
0: Indicates that this switch is set
13)EFD_D2P_SEND_PAGING_O
Whether the RNC sends paging m
1: Indicates that this switch is set
0: Indicates that this switch is set
14)SRB_OVER_HSPA_OPT_BA
Whether to optimize the call drop
1: Indicates that this switch is set
corresponding RL reestablishmen
0: Indicates that this switch is set
RL reestablishment function is en
15)HO_SS_USER_IDENTIFY_SW
Whether the RNC identifies UEs t
1: Indicates that this switch is set
0: Indicates that this switch is set
16)RRC_REJ_TNLFAIL_CNT_SW
Whether the VS.RRC.Rej.TNL.Fa
1: Indicates that this switch is set
0: Indicates that this switch is set
17)FIX_PFM_SYSOUT_FAIL_SW
Whether to correct the measurem
1: Indicates that this switch is set
a. If the scenario of VS.IRATHO.F
b. If the scenario of VS.IRATHO.F
RsvSwitch21=RESERVED_SWIT
0: Indicates that this switch is set
GUI Value Range: SECU_CU_CR
IUFLEX_CS_IMSI_PAGING_UE_
RL_PROCEDURE_OPT_SWITCH
HO_SS_USER_IDENTIFY_SWIT
Unit: None
Actual Value Range:
SECU_CU_CROSS_IP_OPT_SW
RRC_REL_REDIR_OPT_SWITC
RL_RESET_OVERLAP_CU_OPT
UNSTABLE_PREEMPTED_USE
IUFLEX_CS_IMSI_PAGING_UE_
PCH_DISABLED_USE_EFD_SW
Parameter ID NE MML Command Feature Feature Name
ID
CS_PAGING_OVERLAP_RRC_E
CS_PAGING_OVERLAP_DSCR_
FACH_CU_WITH_CRNTI_OPT_S
RL_PROCEDURE_OPT_SWITCH
FACH_IUR_CU_CELL_RES_ALO
RAB_FAST_RB_SETUP_ACTCF
EFD_D2P_SEND_PAGING_OPT
SRB_OVER_HSPA_OPT_BASED
HO_SS_USER_IDENTIFY_SWIT
RRC_REJ_TNLFAIL_CNT_SWIT
FIX_PFM_SYSOUT_FAIL_SWITC
Default Value:
SECU_CU_CROSS_IP_OPT_SW
ABLED_USE_EFD_SWITCH:0,C
_SWITCH:0,RAB_FAST_RB_SET
CH:0,FIX_PFM_SYSOUT_FAIL_
6)STATE_TRANS_COUNT_OPT
1: Indicates that this switch is set
0: Indicates that this switch is set
7)CU_RB_CFG_OPT_SWITCH(R
Whether the RB configuration info
1:Indicates that this switch is set t
0:Indicates that this switch is set t
8)SEND_RNSAP_RESET_AGAIN
Whether the RNC sends a RESE
1: Indicates that this switch is set
0: Indicates that this switch is set
9)SYS_HO_RELOC_CMP_OPT_
Whether the RNC sends a Reloca
1: Indicates that this switch is set
0: Indicates that this switch is set
10)CSPS_SYS_HO_IN_SMC_SW
Whether the RNC sends two secu
1: Indicates that this switch is set
combined services.
0: Indicates that this switch is set
11)MOCN_REDIR_GET_SPID_O
Whether non-supporting UEs sele
1: Indicates that this switch is set
0: Indicates that this switch is set
12)DCH_DISCARD_NONDCH_C
Whether the RNC discards the CE
entering service area", "periodic c
RNC considers this message abn
1: Indicates that this switch is set
(1)The RNC determines that a UE
transmission", or "paging respons
(2)The RNC receives from a UE a
CELL_DCH state transitions.
0: Indicates that this switch is set
13)CMCF_ACTIVE_RECFG_REE
Whether to trigger RL reestablish
1: Indicates that this switch is set
(1) The compressed mode (CM) i
(2) The RNC triggers a CM recon
(3) An SRB reset, a TRB reset, an
Parameter ID NE MML Command Feature Feature Name
ID
DCH_DISCARD_NONDCH_CU_
CMCF_ACTIVE_RECFG_REEST
DCH_RB_REL_CU_OVERLAP_O
FACH_SRNS_CONTEXT_REQ_
CSFB_USER_IDENTIFY_OPT_S
F2D_RBSETUP_CU_OVERLAP_
INIT_DT_OVERLAP_CU_OPT_S
SRVCC_RELOC_IN_CIPHER_O
RLREEST_RAB_SETUPFAIL_CN
MOCN_SAME_DOMAIN_DISC_I
RL_PROCEDURE_OPT_SWITCH
RABSETUP_OVERLAP_CU_REL
RL_CNT_OPT_SWITCH,
TRNC_RELOC_IN_SUCC_OPT_
RELOC_WITHOUT_GLOBAL_CN
RELOC_ACK_WAIT_IUUP_INIT_
ASU_CU_CROSS_OPT_ENH_S
RB_RL_REEST_OPT_ENH_SWI
DCH_CU_CHGCELL_OPT_SWIT
RELOC_SILENT_DETECT_SWIT
RL_FAIL_SUSP_SHO_DEL_SWI
Default Value:
PS_RAB_REL_GTPU_RESOURC
VERLAP_CU_TRIG_DSCR_SWI
OCN_REDIR_GET_SPID_OPT_S
FB_USER_IDENTIFY_OPT_SWI
SAME_DOMAIN_DISC_INIT_DT
N_ID_OPT_SWITCH:0,RELOC_A
SP_SHO_DEL_SWITCH:0
TRNC_RELOC_IN_SUCC_OPT_
DCH_CU_CHGCELL_OPT_SWIT
Unit: None
Actual Value Range:
PS_RAB_REL_GTPU_RESOURC
MNTN_TWO_PENDING_INTEGR
DCCC_HHO_CU_NO_CHANGIN
RAB_MODIFY_NO_CHANGING_
IUR_F2P_P2P_OVERLAP_CU_T
STATE_TRANS_COUNT_OPT_S
CU_RB_CFG_OPT_SWITCH,
SEND_RNSAP_RESET_AGAIN_
SYS_HO_RELOC_CMP_OPT_S
CSPS_SYS_HO_IN_SMC_SWIT
MOCN_REDIR_GET_SPID_OPT
DCH_DISCARD_NONDCH_CU_
CMCF_ACTIVE_RECFG_REEST
DCH_RB_REL_CU_OVERLAP_O
FACH_SRNS_CONTEXT_REQ_
CSFB_USER_IDENTIFY_OPT_S
F2D_RBSETUP_CU_OVERLAP_
INIT_DT_OVERLAP_CU_OPT_S
SRVCC_RELOC_IN_CIPHER_O
RLREEST_RAB_SETUPFAIL_CN
MOCN_SAME_DOMAIN_DISC_I
RL_PROCEDURE_OPT_SWITCH
RABSETUP_OVERLAP_CU_REL
RL_CNT_OPT_SWITCH,
TRNC_RELOC_IN_SUCC_OPT_
RELOC_WITHOUT_GLOBAL_CN
RELOC_ACK_WAIT_IUUP_INIT_
ASU_CU_CROSS_OPT_ENH_S
RB_RL_REEST_OPT_ENH_SWI
DCH_CU_CHGCELL_OPT_SWIT
RELOC_SILENT_DETECT_SWIT
RL_FAIL_SUSP_SHO_DEL_SWI
Default Value:
PS_RAB_REL_GTPU_RESOURC
VERLAP_CU_TRIG_DSCR_SWI
OCN_REDIR_GET_SPID_OPT_S
FB_USER_IDENTIFY_OPT_SWI
Parameter ID NE MML Command Feature Feature Name
ID
SAME_DOMAIN_DISC_INIT_DT
N_ID_OPT_SWITCH:0,RELOC_A
SP_SHO_DEL_SWITCH:0
DLAInRlcSuspendTrigF BSC69 SET USTATETIMER WRFD- HSDPA State Meaning: Delay in suspending RL
orH2F 00 010611 Transition parameter so as to reduce the inv
11 transmission suspension for H2F
GUI Value Range: 0~1000
Unit: ms
Actual Value Range: 0~1000
Default Value: 0
DLAInRlcSuspendTrigF BSC69 SET USTATETIMER WRFD- HSDPA State Meaning: Delay in suspending RL
orH2F 10 010611 Transition parameter so as to reduce the inv
11 transmission suspension for H2F
GUI Value Range: 0~1000
Unit: ms
Actual Value Range: 0~1000
Default Value: 0
30. PERFENH_HO_TARG_3GCE
1: When this switch is turned on,
0: When this switch is turned off,
31. PERFENH_D2F_F2D_MSG_
1: When this switch is turned on,
CycleLengthCoeff", "maxAllowedU
0: When this switch is turned off,
GUI Value Range: PERFENH_MR
PERFENH_NR_OF_DL_CHLCOD
PERFENH_SRB_D2H_BASE_CO
PERFENH_VOICE_DEEPCOVER
PERFENH_RRCDRD_CELL_RA
PERFENH_IUUP2_AMR_RATES
PERFENH_EDCH_THROU_ULD
PERFENH_PERMIT_LTE_SUB_
Unit: None
Actual Value Range:
PERFENH_MR_AGPS_FAIL_CE
PERFENH_RRC_REDIR_PS_IDE
PERFENH_RRC_REDIR_PS_INC
PERFENH_REDIR_OTHER_FB_
PERFENH_NR_OF_DL_CHLCOD
PERFENH_SRNSR_IUB_DM_TE
PERFENH_INTERRAT_HO_PEN
PERFENH_QOS_ENHANCE_SW
PERFENH_SRB_D2H_BASE_CO
PERFENH_SRB_H2D_CODE_JU
PERFENH_HOPRIOMEASTIMER
PERFENH_1X_MC_SETUP_DEA
PERFENH_VOICE_DEEPCOVER
PERFENH_CSPS_CACFAIL_PS
PERFENH_PS_STRM_HIGHRAT
PERFENH_CACFAIL_RRC_RED
PERFENH_RRCDRD_CELL_RA
PERFENH_IUUP2_AMR_MBR_L
PERFENH_AMR_RATESET_SYM
PERFENH_IUUP2_AMR_RATES
PERFENH_IUUP2_AMR_RATES
PERFENH_MR_RTT_MEAS_NO
PERFENH_SRBODCH_ERR_TB
PERFENH_HSDPA_4AMEAS_O
Parameter ID NE MML Command Feature Feature Name
ID
PERFENH_EDCH_THROU_ULD
PERFENH_SERV_DIFF_ZERO_
PERFENH_PERMIT_LTE_SUB_
PERFENH_PERMIT_LTE_SUB_
PERFENH_PERMIT_LTE_SUB_
PERFENH_HO_TARG_3GCELL_
PERFENH_D2F_F2D_MSG_OPT
Default Value: PERFENH_MR_A
PERFENH_REDIR_OTHER_FB_
PERFENH_QOS_ENHANCE_SW
PERFENH_1X_MC_SETUP_DEA
PERFENH_CACFAIL_RRC_RED
PERFENH_IUUP2_AMR_RATES
PERFENH_HSDPA_4AMEAS_O
PERFENH_PERMIT_LTE_SUB_
31. PERFENH_D2F_F2D_MSG_
1: When this switch is turned on,
CycleLengthCoeff", "maxAllowedU
0: When this switch is turned off,
GUI Value Range: PERFENH_MR
PERFENH_NR_OF_DL_CHLCOD
PERFENH_SRB_D2H_BASE_CO
PERFENH_VOICE_DEEPCOVER
PERFENH_RRCDRD_CELL_RA
PERFENH_IUUP2_AMR_RATES
PERFENH_EDCH_THROU_ULD
PERFENH_PERMIT_LTE_SUB_
Unit: None
Actual Value Range:
PERFENH_MR_AGPS_FAIL_CE
PERFENH_RRC_REDIR_PS_IDE
PERFENH_RRC_REDIR_PS_INC
PERFENH_REDIR_OTHER_FB_
PERFENH_NR_OF_DL_CHLCOD
PERFENH_SRNSR_IUB_DM_TE
PERFENH_INTERRAT_HO_PEN
PERFENH_QOS_ENHANCE_SW
PERFENH_SRB_D2H_BASE_CO
PERFENH_SRB_H2D_CODE_JU
PERFENH_HOPRIOMEASTIMER
PERFENH_1X_MC_SETUP_DEA
PERFENH_VOICE_DEEPCOVER
PERFENH_CSPS_CACFAIL_PS
PERFENH_PS_STRM_HIGHRAT
PERFENH_CACFAIL_RRC_RED
PERFENH_RRCDRD_CELL_RA
PERFENH_IUUP2_AMR_MBR_L
PERFENH_AMR_RATESET_SYM
PERFENH_IUUP2_AMR_RATES
PERFENH_IUUP2_AMR_RATES
PERFENH_MR_RTT_MEAS_NO
PERFENH_SRBODCH_ERR_TB
PERFENH_HSDPA_4AMEAS_O
PERFENH_EDCH_THROU_ULD
PERFENH_SERV_DIFF_ZERO_
PERFENH_PERMIT_LTE_SUB_
Parameter ID NE MML Command Feature Feature Name
ID
PERFENH_PERMIT_LTE_SUB_
PERFENH_PERMIT_LTE_SUB_
PERFENH_HO_TARG_3GCELL_
PERFENH_D2F_F2D_MSG_OPT
Default Value: PERFENH_MR_A
PERFENH_REDIR_OTHER_FB_
PERFENH_QOS_ENHANCE_SW
PERFENH_1X_MC_SETUP_DEA
PERFENH_CACFAIL_RRC_RED
PERFENH_IUUP2_AMR_RATES
PERFENH_HSDPA_4AMEAS_O
PERFENH_PERMIT_LTE_SUB_
TAC_FUNC BSC69 ADD UIMEITAC WRFD- Terminal Black Meaning: The function of the TAC
00 MOD UIMEITAC 160103 List on HSDPA, however, the RNC se
RMV UIMEITAC WRFD- Enhanced Fast TAC specifies the UEs that are en
020500 Dormancy the UE in the CELL_FACH or CE
GUI Value Range: Fast_Dormanc
Unit: None
Actual Value Range: Fast_Dorma
Default Value: None
TAC_FUNC BSC69 ADD UIMEITAC WRFD- Terminal Black Meaning: The function of the TAC
10 MOD UIMEITAC 160103 List on HSDPA, however, the RNC se
RMV UIMEITAC WRFD- Enhanced Fast TAC specifies the UEs that are en
020500 Dormancy the UE in the CELL_FACH or CE
GUI Value Range: Fast_Dormanc
Unit: None
Actual Value Range: Fast_Dorma
Default Value: None
BeD2FStateTransTimer BSC69 SET WRFD- UE State in Meaning: Timer for state transition
00 UUESTATETRANST 010202 Connected
IMER GUI Value Range: 1~65535
Mode (CELL- Unit: s
DCH, CELL-
PCH, URA- Actual Value Range: 1~65535
PCH, CELL- Default Value: 5
FACH)
BeD2FStateTransTimer BSC69 SET WRFD- UE State in Meaning: Timer for state transition
10 UUESTATETRANST 010202 Connected
IMER GUI Value Range: 1~65535
Mode (CELL- Unit: s
DCH, CELL-
PCH, URA- Actual Value Range: 1~65535
PCH, CELL- Default Value: 5
FACH)
BeD2FStateTransTimer BSC69 ADD WRFD- UE State in Meaning: Timer for state transition
00 UCELLUESTATETR 010202 Connected
ANS GUI Value Range: 1~65535
Mode (CELL- Unit: s
MOD
UCELLUESTATETR DCH, CELL-
PCH, URA- Actual Value Range: 1~65535
ANS
PCH, CELL- Default Value: 5
FACH)
BeD2FStateTransTimer BSC69 ADD WRFD- UE State in Meaning: Timer for state transition
10 UCELLUESTATETR 010202 Connected
ANS GUI Value Range: 1~65535
Mode (CELL- Unit: s
MOD
UCELLUESTATETR DCH, CELL-
PCH, URA- Actual Value Range: 1~65535
ANS
PCH, CELL- Default Value: 5
FACH)
D2FTvmTimeToTrig BSC69 SET WRFD- UE State in Meaning: When the traffic volume
00 UUESTATETRANS 010202 Connected GUI Value Range: D0, D10, D20,
Mode (CELL- Unit: ms
DCH, CELL-
PCH, URA- Actual Value Range: 0, 10, 20, 40
PCH, CELL- Default Value: D5000
FACH)
D2FTvmTimeToTrig BSC69 SET WRFD- UE State in Meaning: When the traffic volume
10 UUESTATETRANS 010202 Connected GUI Value Range: D0, D10, D20,
Mode (CELL- Unit: ms
DCH, CELL-
PCH, URA- Actual Value Range: 0, 10, 20, 40
PCH, CELL- Default Value: D5000
FACH)
D2FTvmPTAT BSC69 SET WRFD- UE State in Meaning: Pending time after the t
00 UUESTATETRANS 010202 Connected GUI Value Range: D250, D500, D
Mode (CELL- Unit: ms
DCH, CELL-
Actual Value Range: 250, 500, 10
PCH, URA-
PCH, CELL- Default Value: D1000
FACH)
D2FTvmPTAT BSC69 SET WRFD- UE State in Meaning: Pending time after the t
10 UUESTATETRANS 010202 Connected GUI Value Range: D250, D500, D
Mode (CELL- Unit: ms
DCH, CELL-
PCH, URA- Actual Value Range: 250, 500, 10
PCH, CELL- Default Value: D1000
FACH)
BeH2FStateTransTimer BSC69 SET WRFD- UE State in Meaning: Timer for state transition
00 UUESTATETRANST 010202 Connected
IMER GUI Value Range: 1~65535
Mode (CELL- Unit: s
DCH, CELL-
Actual Value Range: 1~65535
Parameter ID NE MML Command Feature Feature Name
ID
BeH2FStateTransTimer BSC69 SET WRFD- UE State in Meaning: Timer for state transition
10 UUESTATETRANST 010202 Connected
IMER GUI Value Range: 1~65535
WRFD- Mode (CELL- Unit: s
010611 DCH, CELL- Actual Value Range: 1~65535
11 PCH, URA-
PCH, CELL- Default Value: 5
FACH)
HSDPA State
Transition
BeH2FStateTransTimer BSC69 ADD WRFD- UE State in Meaning: Timer for state transition
00 UCELLUESTATETR 010202 Connected
ANS GUI Value Range: 1~65535
Mode (CELL- Unit: s
MOD
UCELLUESTATETR DCH, CELL-
PCH, URA- Actual Value Range: 1~65535
ANS
PCH, CELL- Default Value: 5
FACH)
BeH2FStateTransTimer BSC69 ADD WRFD- UE State in Meaning: Timer for state transition
10 UCELLUESTATETR 010202 Connected
ANS GUI Value Range: 1~65535
Mode (CELL- Unit: s
MOD
UCELLUESTATETR DCH, CELL-
PCH, URA- Actual Value Range: 1~65535
ANS
PCH, CELL- Default Value: 5
FACH)
BeH2FTvmTimeToTrig BSC69 SET WRFD- UE State in Meaning: When the traffic volume
00 UUESTATETRANS 010202 Connected GUI Value Range: D0, D10, D20,
WRFD- Mode (CELL- Unit: ms
010611 DCH, CELL-
PCH, URA- Actual Value Range: 0, 10, 20, 40
11
PCH, CELL- Default Value: D5000
FACH)
HSDPA State
Transition
BeH2FTvmTimeToTrig BSC69 SET WRFD- UE State in Meaning: When the traffic volume
10 UUESTATETRANS 010202 Connected GUI Value Range: D0, D10, D20,
WRFD- Mode (CELL- Unit: ms
010611 DCH, CELL-
Actual Value Range: 0, 10, 20, 40
11 PCH, URA-
PCH, CELL- Default Value: D5000
FACH)
HSDPA State
Transition
BeH2FTvmPTAT BSC69 SET WRFD- UE State in Meaning: Pending time after the t
00 UUESTATETRANS 010202 Connected GUI Value Range: D250, D500, D
WRFD- Mode (CELL- Unit: ms
010611 DCH, CELL-
PCH, URA- Actual Value Range: 250, 500, 10
11
PCH, CELL- Default Value: D1000
FACH)
HSDPA State
Transition
BeH2FTvmPTAT BSC69 SET WRFD- UE State in Meaning: Pending time after the t
10 UUESTATETRANS 010202 Connected GUI Value Range: D250, D500, D
WRFD- Mode (CELL- Unit: ms
010611 DCH, CELL-
Actual Value Range: 250, 500, 10
11 PCH, URA-
PCH, CELL- Default Value: D1000
FACH)
HSDPA State
Transition
Parameter ID NE MML Command Feature Feature Name
ID
RtDH2FStateTransTime BSC69 SET WRFD- UE State in Meaning: Timer for state transition
r 00 UUESTATETRANST 010202 Connected
IMER GUI Value Range: 1~65535
Mode (CELL- Unit: s
DCH, CELL-
PCH, URA- Actual Value Range: 1~65535
PCH, CELL- Default Value: 180
FACH)
RtDH2FStateTransTime BSC69 SET WRFD- UE State in Meaning: Timer for state transition
r 10 UUESTATETRANST 010202 Connected
IMER GUI Value Range: 1~65535
Mode (CELL- Unit: s
DCH, CELL-
PCH, URA- Actual Value Range: 1~65535
PCH, CELL- Default Value: 180
FACH)
RtDH2FTvmTimeToTrig BSC69 SET WRFD- UE State in Meaning: When the traffic volume
00 UUESTATETRANS 010202 Connected GUI Value Range: D0, D10, D20,
Mode (CELL- Unit: ms
DCH, CELL-
PCH, URA- Actual Value Range: 0, 10, 20, 40
PCH, CELL- Default Value: D5000
FACH)
RtDH2FTvmTimeToTrig BSC69 SET WRFD- UE State in Meaning: When the traffic volume
10 UUESTATETRANS 010202 Connected GUI Value Range: D0, D10, D20,
Mode (CELL- Unit: ms
DCH, CELL-
Actual Value Range: 0, 10, 20, 40
PCH, URA-
PCH, CELL- Default Value: D5000
FACH)
Parameter ID NE MML Command Feature Feature Name
ID
RtDH2FTvmPTAT BSC69 SET WRFD- UE State in Meaning: Pending time after the t
00 UUESTATETRANS 010202 Connected GUI Value Range: D250, D500, D
Mode (CELL- Unit: ms
DCH, CELL-
PCH, URA- Actual Value Range: 250, 500, 10
PCH, CELL- Default Value: D16000
FACH)
RtDH2FTvmPTAT BSC69 SET WRFD- UE State in Meaning: Pending time after the t
10 UUESTATETRANS 010202 Connected GUI Value Range: D250, D500, D
Mode (CELL- Unit: ms
DCH, CELL-
PCH, URA- Actual Value Range: 250, 500, 10
PCH, CELL- Default Value: D16000
FACH)
BeE2FStateTransTimer BSC69 SET WRFD- UE State in Meaning: Timer for state transition
00 UUESTATETRANST 010202 Connected
IMER GUI Value Range: 1~65535
Mode (CELL- Unit: s
DCH, CELL-
PCH, URA- Actual Value Range: 1~65535
PCH, CELL- Default Value: 2
FACH)
BeE2FStateTransTimer BSC69 SET WRFD- UE State in Meaning: Timer for state transition
10 UUESTATETRANST 010202 Connected
IMER GUI Value Range: 1~65535
Mode (CELL- Unit: s
DCH, CELL-
PCH, URA- Actual Value Range: 1~65535
PCH, CELL- Default Value: 2
FACH)
BeE2FStateTransTimer BSC69 ADD WRFD- UE State in Meaning: Timer for state transition
00 UCELLUESTATETR 010202 Connected
ANS GUI Value Range: 1~65535
Mode (CELL- Unit: s
MOD
UCELLUESTATETR DCH, CELL-
PCH, URA- Actual Value Range: 1~65535
ANS
PCH, CELL- Default Value: 2
FACH)
BeE2FStateTransTimer BSC69 ADD WRFD- UE State in Meaning: Timer for state transition
10 UCELLUESTATETR 010202 Connected
ANS GUI Value Range: 1~65535
Mode (CELL- Unit: s
MOD
UCELLUESTATETR DCH, CELL-
Actual Value Range: 1~65535
ANS PCH, URA-
PCH, CELL- Default Value: 2
FACH)
Parameter ID NE MML Command Feature Feature Name
ID
Configuration
Control (DCCC)
HSUPA DCCC
BeF2HTvmThd BSC69 ADD WRFD- HSDPA State Meaning: This parameter specifie
00 UCELLUESTATETR 010611 Transition the "SET UUESTATETRANS" co
ANS
11 "BeH2FTvmThd" parameter as th
MOD
UCELLUESTATETR GUI Value Range: D16, D32, D64
ANS Unit: byte
Actual Value Range: 16, 32, 64, 1
Default Value: D256
BeF2HTvmThd BSC69 ADD WRFD- HSDPA State Meaning: This parameter specifie
10 UCELLUESTATETR 010611 Transition the "SET UUESTATETRANS" co
ANS
11 "BeH2FTvmThd" parameter as th
MOD
UCELLUESTATETR GUI Value Range: D16, D32, D64
ANS Unit: byte
Actual Value Range: 16, 32, 64, 1
Default Value: D256
DRA_R99_DL_FLOW_CONTRO
DRA_SMART_FAST_STATE_TR
DRA_BASE_LOAD_HBD_INIT_S
Default Value: DRA_AQM_SWITC
DRA_BASE_COVER_BE_TTI_R
DRA_HSDPA_STATE_TRANS_S
DRA_PS_NON_BE_STATE_TRA
DRA_CSPS_NO_PERIOD_RETR
DRA_BASE_COVER_BE_TTI_IN
DcccStg BSC69 SET UDCCC WRFD- Dynamic Meaning: Strategy for adjustment
00 021101 Channel over the DCH can only be raised.
Configuration GUI Value Range: RATE_UP_AN
Control (DCCC) Unit: None
Actual Value Range: RATE_UP_A
Default Value: RATE_UP_AND_D
DcccStg BSC69 SET UDCCC WRFD- Dynamic Meaning: Strategy for adjustment
10 021101 Channel over the DCH can only be raised.
Configuration GUI Value Range: RATE_UP_AN
Control (DCCC) Unit: None
Actual Value Range: RATE_UP_A
Parameter ID NE MML Command Feature Feature Name
ID
UlDcccRateThd BSC69 SET UDCCC WRFD- Dynamic Meaning: Uplink bit rate threshold
00 021101 Channel UE.
Configuration GUI Value Range: D8, D16, D32,
Control (DCCC) Unit: kbit/s
Actual Value Range: 8, 16, 32, 64
Default Value: D64
UlDcccRateThd BSC69 SET UDCCC WRFD- Dynamic Meaning: Uplink bit rate threshold
10 021101 Channel UE.
Configuration GUI Value Range: D8, D16, D32,
Control (DCCC) Unit: kbit/s
Actual Value Range: 8, 16, 32, 64
Default Value: D64
DlDcccRateThd BSC69 SET UDCCC WRFD- Dynamic Meaning: Downlink bit rate thresh
00 021101 Channel effect for the UE.
WRFD- Configuration GUI Value Range: D8, D16, D32,
020107 Control (DCCC) Unit: kbit/s
Overload Actual Value Range: 8, 16, 32, 64
Control
Default Value: D64
DlDcccRateThd BSC69 SET UDCCC WRFD- Dynamic Meaning: Downlink bit rate thresh
10 021101 Channel effect for the UE.
WRFD- Configuration GUI Value Range: D8, D16, D32,
020107 Control (DCCC) Unit: kbit/s
Overload Actual Value Range: 8, 16, 32, 64
Control
Default Value: D64
26. PERFENH_MBDR_TARCELL
selected as the target cell. When
27. PERFENH_RRC_DRD_PREA
decision on intra-RAT DRDs or re
28. PERFENH_RRC_WEAK_RED
redirection. When this switch is tu
29. PERFENH_L2U_CSFB_COM
time PS service, the channel type
the standard access procedure. If
off, the UE follows the standard a
30. PERFENH_DLBLINDDETECT
blind detection is enabled.
31. PERFENH_DLBLINDDETECT
is enabled if the HSDPA service h
32. PERFENH_R6_HSUPA_TTI_
work.
This parameter is an advanced pa
GUI Value Range: PERFENH_AM
PERFENH_INTRAFREQ_MC_TM
PERFENH_RL_RECFG_SIR_CO
PERFENH_TX_INTERRUPT_AF
PERFENH_OLPC_BLER_COEF_
PERFENH_IS_TIMEOUT_TRIG_
PERFENH_RRC_WEAK_REDIR
PERFENH_R6_HSUPA_TTI_10M
Unit: None
Actual Value Range:
PERFENH_AMR_SPEC_BR_SW
PERFENH_INTRAFREQ_MC_TM
PERFENH_UU_P2D_CUC_OPT_
PERFENH_VIP_USER_PCHR_M
PERFENH_TX_INTERRUPT_AF
PERFENH_HSUPA_TTI_RECFG
PERFENH_MULTI_RLS_CQI_PA
PERFENH_RELOC_IE_CALCTIM
PERFENH_RRC_DRD_PREADM
PERFENH_RRC_WEAK_REDIR
PERFENH_L2U_CSFB_COMMC
PERFENH_DLBLINDDETECT_W
PERFENH_DLBLINDDETECT_W
PERFENH_R6_HSUPA_TTI_10M
Default Value:
PERFENH_AMR_SPEC_BR_SW
Parameter ID NE MML Command Feature Feature Name
ID
CH:1,PERFENH_INTERRAT_PE
ER_SWITCH:1,PERFENH_RRC_
PERFENH_CELL_HSUPA_CAP_
PERFENH_HSUPA_TTI_RECFG
OPT_SWITCH:0,PERFENH_REL
H_RRC_DRD_PREADMISSION_
BAMRONDCH:0,PERFENH_R6_
18. PERFENH_HSUPA_TTI_REC
When this switch is turned off, the
When this switch is turned on, the
insufficient coverage, these UEs c
19. PERFENH_DOWNLOAD_EN
20. PERFENH_OLPC_BLER_CO
set by the OMU board if the best
21. PERFENH_EMG_AGPS_MC
RNC delays the sending of this m
22. PERFENH_MULTI_RLS_CQI
the "SET UHSDPCCH" and "ADD
of the two parameters that are for
23. PERFENH_RELOC_IE_CALC
When this switch is turned on, sta
24. PERFENH_IS_TIMEOUT_TR
switch is turned off, the DRD proc
and channel switchover from E-D
25. PERFENH_CELL_CACLOAD
When this switch is turned on, the
resource congestion. When this s
26. PERFENH_MBDR_TARCELL
selected as the target cell. When
27. PERFENH_RRC_DRD_PREA
decision on intra-RAT DRDs or re
28. PERFENH_RRC_WEAK_RED
redirection. When this switch is tu
29. PERFENH_L2U_CSFB_COM
time PS service, the channel type
the standard access procedure. If
off, the UE follows the standard a
30. PERFENH_DLBLINDDETECT
blind detection is enabled.
31. PERFENH_DLBLINDDETECT
is enabled if the HSDPA service h
32. PERFENH_R6_HSUPA_TTI_
work.
This parameter is an advanced pa
GUI Value Range: PERFENH_AM
PERFENH_INTRAFREQ_MC_TM
PERFENH_RL_RECFG_SIR_CO
PERFENH_TX_INTERRUPT_AF
PERFENH_OLPC_BLER_COEF_
PERFENH_IS_TIMEOUT_TRIG_
Parameter ID NE MML Command Feature Feature Name
ID
PERFENH_RRC_WEAK_REDIR
PERFENH_R6_HSUPA_TTI_10M
Unit: None
Actual Value Range:
PERFENH_AMR_SPEC_BR_SW
PERFENH_INTRAFREQ_MC_TM
PERFENH_UU_P2D_CUC_OPT_
PERFENH_VIP_USER_PCHR_M
PERFENH_TX_INTERRUPT_AF
PERFENH_HSUPA_TTI_RECFG
PERFENH_MULTI_RLS_CQI_PA
PERFENH_RELOC_IE_CALCTIM
PERFENH_RRC_DRD_PREADM
PERFENH_RRC_WEAK_REDIR
PERFENH_L2U_CSFB_COMMC
PERFENH_DLBLINDDETECT_W
PERFENH_DLBLINDDETECT_W
PERFENH_R6_HSUPA_TTI_10M
Default Value:
PERFENH_AMR_SPEC_BR_SW
CH:1,PERFENH_INTERRAT_PE
ER_SWITCH:1,PERFENH_RRC_
PERFENH_CELL_HSUPA_CAP_
PERFENH_HSUPA_TTI_RECFG
OPT_SWITCH:0,PERFENH_REL
H_RRC_DRD_PREADMISSION_
BAMRONDCH:0,PERFENH_R6_
Default Value: 64
CS_HHO_ASYNC_CTRL_SWITC
RB_REL_RL_REEST_SWITCH,
UL_DUAL_MODE_UE_D2P_OR_
PHYCHRECFG_ENH_RL_REES
RBRECFG_ENH_RL_REEST_SW
SMC_STOP_RLC_SWITCH,
GTP_SN_IN_RAB_REL_INIT_BY
CMP_IU_QOS_GTP_PDU_SN_S
DL_TRB_RESET_BUFF_SWITC
RRC_CELLFACH_DL_TRB_RES
RAB_ASS_MOD_TNL_ADDR_SU
Default Value:
PS_F2D_OVERLAP_CELLUPT_
CELERATOR_SWITCH:0,RRC_C
_HHO_ASYNC_CTRL_SWITCH:
ETUP_ENHANCE_RL_REEST_S
H:0,PHYCHRECFG_ENH_RL_RE
UFF_SWITCH:0,RRC_CELLFAC
PTTE2FThrouThd BSC69 SET WRFD- Push to Talk Meaning: Absolute threshold for t
00 UPTTSTATETRANS 020134 period is calculated by multiplying
GUI Value Range: 0~38400
Unit: 10bit/s
Actual Value Range: 0~384000
Default Value: 1
PTTE2FThrouThd BSC69 SET WRFD- Push to Talk Meaning: Absolute threshold for t
10 UPTTSTATETRANS 020134 period is calculated by multiplying
GUI Value Range: 0~38400
Unit: 10bit/s
Actual Value Range: 0~384000
Default Value: 1
PTTDH2FTvmThd BSC69 SET WRFD- Push to Talk Meaning: Absolute threshold for t
00 UPTTSTATETRANS 020134 triggered.
GUI Value Range: D8, D16, D32,
Unit: byte
Actual Value Range: 8, 16, 32, 64
Default Value: D8
PTTDH2FTvmThd BSC69 SET WRFD- Push to Talk Meaning: Absolute threshold for t
10 UPTTSTATETRANS 020134 triggered.
GUI Value Range: D8, D16, D32,
Parameter ID NE MML Command Feature Feature Name
ID
Unit: byte
Actual Value Range: 8, 16, 32, 64
Default Value: D8
14. PERFENH_FORBIDDEN_DR
algorithm to adjust its channel typ
15. PERFENH_AGPS_MR_USE_
1: When this switch is set to on, th
the SPECUSER_AGPS_MEAS_E
0: When this switch is set to off, th
the SPECUSER_AGPS_MEAS_E
16. PERFENH_SRB_H2D_D2P2
HSDPA. D2P refers to the state tr
1: When this switch is set to on, S
0: When this switch is set to off, S
17. PERFENH_IUB_MR_USING_
1: When this switch is turned on,
0: When this switch is turned off,
18.PERFENH_FACH_TVM_MC_
1: This switch is turned on. The R
parameters remain unchanged on
0: This switch is turned off. The R
19.PERFENH_FACH_RELOC_IN
initiated by UEs complying with R
1: This switch is turned on. The R
0: This switch is turned off. The R
20.PERFENH_DRNC_MR_REPO
1: When this switch is set to on, U
0: When this switch is set to off, U
21. PERFENH_RELOC_UE_AGP
set to on, the RNC does not deliv
measurement control messages t
22. PERFENH_CSPS_RELOCIN
services experience a combined h
1: This switch is turned on. In the
0: This switch is turned off. The R
23. PERFENH_AMR_CUC_TFI_O
1: This switch is turned on and the
0: This switch is turned off and the
24. PERFENH_AMR_TFC_CTRL
1: This switch is turned on and the
If L3 receives a confirmation abou
CTRL FAIL message before the t
the TFC CTRL FAIL message, the
0: This switch is turned off. If the U
Parameter ID NE MML Command Feature Feature Name
ID
25. PERFENH_RATE_CTRL_AC
effect.
1: This switch is turned on and the
0: This switch is turned off and the
26. PERFENH_LCS_IN_RELOC_
1: This switch is turned on. The R
0: This switch is turned off. The R
27. PERFENH_MBDR_INTER_R
inter-RAT handovers is decided b
decided by the maximum percent
28. PERFENH_EDCH_OLPC_MC
measurement control includes me
the algorithm for adaptive adjustm
1: This switch is turned on. The R
0: This switch is turned off. The R
29. PERFENH_ADJACENT_INDE
neighboring frequencies without s
1: This switch is turned on. The in
0: This switch is turned off. The in
30. PERFENH_SEND_CTFC_WH
1: This switch is turned on and the
31. PERFENH_RB_SETUP_DRD
event, preventing RB setup failure
32. PERFENH_IUR_F2D_REF_D
1: This switch is turned on. The R
phase.
0: This switch is turned off. The R
GUI Value Range: PERFENH_U2
PERFENH_CM_STATE_FORBID
PERFENH_COMACROMICRO_H
PERFENH_SERV_LTE_MC_PUN
PERFENH_SRB_H2D_D2P2D_O
PERFENH_DRNC_MR_REPORT
PERFENH_AMR_TFC_CTRL_QU
PERFENH_EDCH_OLPC_MC_O
PERFENH_IUR_F2D_REF_DRN
Unit: None
Actual Value Range:
PERFENH_U2L_PUNISH_HOLD
PERFENH_IUCS_REL_TRIG_U2
PERFENH_CM_STATE_FORBID
PERFENH_UE_CAP_ENQUIRY_
Parameter ID NE MML Command Feature Feature Name
ID
PERFENH_CU_RELOC_IN_CUC
PERFENH_DIVERSITY_PARA_O
PERFENH_COMACROMICRO_H
PERFENH_AMRC_IUB_BW_RSP
PERFENH_AMR_SRNSR_IN_CH
PERFENH_NCELL_ORDER_OP
PERFENH_SERV_LTE_MC_PUN
PERFENH_DCCC_INIT_RATE_O
PERFENH_FORBIDDEN_DRD_W
PERFENH_AGPS_MR_USE_BLK
PERFENH_SRB_H2D_D2P2D_O
PERFENH_IUB_MR_USING_EX
PERFENH_FACH_TVM_MC_TIM
PERFENH_FACH_RELOC_IN_C
PERFENH_DRNC_MR_REPORT
PERFENH_RELOC_UE_AGPS_M
PERFENH_CSPS_RELOCIN_HU
PERFENH_AMR_CUC_TFI_OPT
PERFENH_AMR_TFC_CTRL_QU
PERFENH_RATE_CTRL_ACK_M
PERFENH_LCS_IN_RELOC_PR
PERFENH_MBDR_INTER_RAT_
PERFENH_EDCH_OLPC_MC_O
PERFENH_ADJACENT_INDEX_
PERFENH_SEND_CTFC_WHEN
PERFENH_RB_SETUP_DRD_O
PERFENH_IUR_F2D_REF_DRN
Default Value:
PERFENH_U2L_SERV_NOT_TR
RFENH_UE_CAP_ENQUIRY_OP
SP_PROC_OPT_SWITCH:1,PER
_FORBIDDEN_DRD_WHEN_LTE
OPT_SWITCH:0,PERFENH_FAC
ENH_AMR_CUC_TFI_OPT_SWI
HO_RATIO_OPT_SW:0,PERFEN
0,PERFENH_IUR_F2D_REF_DR
28. PERFENH_EDCH_OLPC_MC
measurement control includes me
the algorithm for adaptive adjustm
1: This switch is turned on. The R
0: This switch is turned off. The R
29. PERFENH_ADJACENT_INDE
neighboring frequencies without s
1: This switch is turned on. The in
0: This switch is turned off. The in
30. PERFENH_SEND_CTFC_WH
1: This switch is turned on and the
31. PERFENH_RB_SETUP_DRD
event, preventing RB setup failure
32. PERFENH_IUR_F2D_REF_D
1: This switch is turned on. The R
phase.
0: This switch is turned off. The R
GUI Value Range: PERFENH_U2
PERFENH_CM_STATE_FORBID
PERFENH_COMACROMICRO_H
PERFENH_SERV_LTE_MC_PUN
PERFENH_SRB_H2D_D2P2D_O
PERFENH_DRNC_MR_REPORT
PERFENH_AMR_TFC_CTRL_QU
PERFENH_EDCH_OLPC_MC_O
PERFENH_IUR_F2D_REF_DRN
Unit: None
Actual Value Range:
PERFENH_U2L_PUNISH_HOLD
PERFENH_IUCS_REL_TRIG_U2
PERFENH_CM_STATE_FORBID
PERFENH_UE_CAP_ENQUIRY_
PERFENH_CU_RELOC_IN_CUC
PERFENH_DIVERSITY_PARA_O
PERFENH_COMACROMICRO_H
PERFENH_AMRC_IUB_BW_RSP
PERFENH_AMR_SRNSR_IN_CH
PERFENH_NCELL_ORDER_OP
PERFENH_SERV_LTE_MC_PUN
PERFENH_DCCC_INIT_RATE_O
PERFENH_FORBIDDEN_DRD_W
PERFENH_AGPS_MR_USE_BLK
Parameter ID NE MML Command Feature Feature Name
ID
PERFENH_SRB_H2D_D2P2D_O
PERFENH_IUB_MR_USING_EX
PERFENH_FACH_TVM_MC_TIM
PERFENH_FACH_RELOC_IN_C
PERFENH_DRNC_MR_REPORT
PERFENH_RELOC_UE_AGPS_M
PERFENH_CSPS_RELOCIN_HU
PERFENH_AMR_CUC_TFI_OPT
PERFENH_AMR_TFC_CTRL_QU
PERFENH_RATE_CTRL_ACK_M
PERFENH_LCS_IN_RELOC_PR
PERFENH_MBDR_INTER_RAT_
PERFENH_EDCH_OLPC_MC_O
PERFENH_ADJACENT_INDEX_
PERFENH_SEND_CTFC_WHEN
PERFENH_RB_SETUP_DRD_O
PERFENH_IUR_F2D_REF_DRN
Default Value:
PERFENH_U2L_SERV_NOT_TR
RFENH_UE_CAP_ENQUIRY_OP
SP_PROC_OPT_SWITCH:1,PER
_FORBIDDEN_DRD_WHEN_LTE
OPT_SWITCH:0,PERFENH_FAC
ENH_AMR_CUC_TFI_OPT_SWI
HO_RATIO_OPT_SW:0,PERFEN
0,PERFENH_IUR_F2D_REF_DR
DlBeAbnH2FHIghTvmT BSC69 SET WRFD- HSDPA State Meaning: High traffic indication th
hd 00 UUESTATETRANS 010611 Transition GUI Value Range: 1~65535
11 Unit: 10byte
Actual Value Range: 10~655350
Default Value: 102
DlBeAbnH2FHIghTvmT BSC69 SET WRFD- HSDPA State Meaning: High traffic indication th
hd 10 UUESTATETRANS 010611 Transition GUI Value Range: 1~65535
11 Unit: 10byte
Actual Value Range: 10~655350
Default Value: 102
DlBeAbnH2FLowThrouT BSC69 SET WRFD- HSDPA State Meaning: Low throughput indicati
hd 00 UUESTATETRANS 010611 Transition GUI Value Range: 1~32
11 Unit: kbit/s
Actual Value Range: 1~32
Default Value: 8
DlBeAbnH2FLowThrouT BSC69 SET WRFD- HSDPA State Meaning: Low throughput indicati
hd 10 UUESTATETRANS 010611 Transition GUI Value Range: 1~32
11 Unit: kbit/s
Actual Value Range: 1~32
Default Value: 8
BeAbnormH2FStateTran BSC69 SET WRFD- HSDPA State Meaning: Timer for CELL_DCH to
sTimer 00 UUESTATETRANST 010611 Transition
IMER GUI Value Range: 1~65535
11 Unit: 0.1s
Actual Value Range: 0.1~6553.5
Default Value: 31
BeAbnormH2FStateTran BSC69 SET WRFD- HSDPA State Meaning: Timer for CELL_DCH to
sTimer 10 UUESTATETRANST 010611 Transition
IMER GUI Value Range: 1~65535
11 Unit: 0.1s
Actual Value Range: 0.1~6553.5
Default Value: 31
AbnH2FPenaltyLen BSC69 SET WRFD- UE State in Meaning: Time for prohibiting the
00 UUESTATETRANS 010202 Connected can be triggered only after the tim
Mode (CELL- GUI Value Range: 1~65535
DCH, CELL-
Parameter ID NE MML Command Feature Feature Name
ID
AbnH2FPenaltyLen BSC69 SET WRFD- UE State in Meaning: Time for prohibiting the
10 UUESTATETRANS 010202 Connected can be triggered only after the tim
WRFD- Mode (CELL- GUI Value Range: 1~65535
010611 DCH, CELL- Unit: s
11 PCH, URA-
PCH, CELL- Actual Value Range: 1~65535
FACH) Default Value: 60
HSDPA State
Transition
ZeroRateUpFailToRelTi BSC69 SET UCOIFTIMER WRFD- Dynamic Meaning: Release timer for the PS
merLen 00 021101 Channel indicate that resources are insuffi
Configuration GUI Value Range: 0~65535
Control (DCCC) Unit: s
Actual Value Range: 0~65535
Default Value: 180
ZeroRateUpFailToRelTi BSC69 SET UCOIFTIMER WRFD- Dynamic Meaning: Release timer for the PS
merLen 10 021101 Channel indicate that resources are insuffi
Configuration GUI Value Range: 0~65535
Control (DCCC) Unit: s
Actual Value Range: 0~65535
Default Value: 180
Parking4ADiscardTimer BSC69 SET WRFD- RB Parking Meaning: Timer for the RNC to di
00 UUESTATETRANST 160206 downlink event 4A reports sent by
IMER
state transition triggered by a CS
GUI Value Range: 0~65535
Unit: s
Actual Value Range: 0~65535
Default Value: 60
Parking4ADiscardTimer BSC69 SET WRFD- RB Parking Meaning: Timer for the RNC to di
10 UUESTATETRANST 160206 downlink event 4A reports sent by
IMER
state transition triggered by a CS
GUI Value Range: 0~65535
Parameter ID NE MML Command Feature Feature Name
ID
Unit: s
Actual Value Range: 0~65535
Default Value: 60
LittleRateThd BSC69 SET UDCCC WRFD- Dynamic Meaning: Bit rate threshold for low
00 021101 Channel cannot be performed. The reason
WRFD- Configuration the bit rate for low activity are the
010202 Control (DCCC) GUI Value Range: D0, D8, D16, D
WRFD- UE State in Unit: kbit/s
010611 Connected Actual Value Range: 0, 8, 16, 32,
11 Mode (CELL-
DCH, CELL- Default Value: D8
PCH, URA-
PCH, CELL-
FACH)
HSDPA State
Transition
LittleRateThd BSC69 SET UDCCC WRFD- Dynamic Meaning: Bit rate threshold for low
10 021101 Channel cannot be performed. The reason
WRFD- Configuration the bit rate for low activity are the
010202 Control (DCCC) GUI Value Range: D0, D8, D16, D
Parameter ID NE MML Command Feature Feature Name
ID
BeF2PStateTransTimer BSC69 SET WRFD- UE State in Meaning: Timer for state transition
00 UUESTATETRANST 010202 Connected allowed to switch from CELL_FAC
IMER
WRFD- Mode (CELL- GUI Value Range: 1~65535
04010 DCH, CELL- Unit: s
PCH, URA-
PCH, CELL- Actual Value Range: 1~65535
FACH) Default Value: 65535
BeF2PStateTransTimer BSC69 SET WRFD- UE State in Meaning: Timer for state transition
10 UUESTATETRANST 010202 Connected allowed to switch from CELL_FAC
IMER
WRFD- Mode (CELL- GUI Value Range: 1~65535
04010 DCH, CELL- Unit: s
PCH, URA-
PCH, CELL- Actual Value Range: 1~65535
FACH) Default Value: 65535
BeF2PStateTransTimer BSC69 ADD WRFD- UE State in Meaning: Timer for state transition
00 UCELLUESTATETR 010202 Connected allowed to switch from CELL_FAC
ANS
MOD WRFD- Mode (CELL- GUI Value Range: 1~65535
UCELLUESTATETR 040100 DCH, CELL- Unit: s
ANS PCH, URA-
PCH, CELL- Actual Value Range: 1~65535
FACH) Default Value: 65535
Flow Control
BeF2PStateTransTimer BSC69 ADD WRFD- UE State in Meaning: Timer for state transition
10 UCELLUESTATETR 010202 Connected allowed to switch from CELL_FAC
ANS
WRFD- Mode (CELL- GUI Value Range: 1~65535
040100 DCH, CELL-
Parameter ID NE MML Command Feature Feature Name
ID
F2PTvmTimeToTrig BSC69 SET WRFD- UE State in Meaning: When the traffic volume
00 UUESTATETRANS 010202 Connected GUI Value Range: D0, D10, D20,
Mode (CELL- Unit: ms
DCH, CELL-
PCH, URA- Actual Value Range: 0, 10, 20, 40
PCH, CELL- Default Value: D5000
FACH)
F2PTvmTimeToTrig BSC69 SET WRFD- UE State in Meaning: When the traffic volume
10 UUESTATETRANS 010202 Connected GUI Value Range: D0, D10, D20,
Mode (CELL- Unit: ms
DCH, CELL-
PCH, URA- Actual Value Range: 0, 10, 20, 40
PCH, CELL- Default Value: D5000
FACH)
F2PTvmPTAT BSC69 SET WRFD- UE State in Meaning: Pending time after the t
00 UUESTATETRANS 010202 Connected GUI Value Range: D250, D500, D
Mode (CELL- Unit: ms
DCH, CELL-
PCH, URA- Actual Value Range: 250, 500, 10
PCH, CELL- Default Value: D1000
FACH)
F2PTvmPTAT BSC69 SET WRFD- UE State in Meaning: Pending time after the t
10 UUESTATETRANS 010202 Connected GUI Value Range: D250, D500, D
Mode (CELL- Unit: ms
DCH, CELL-
PCH, URA- Actual Value Range: 250, 500, 10
PCH, CELL- Default Value: D1000
FACH)
18. PERFENH_UL_RL_FAIL_SR
cell is checked. If the target cell is
When this switch is turned off, the
19. PERFENH_HO_SIGNAL_SC
than the following causes. The RN
Originating Streaming Call, Origin
Originating High Priority Signalling
switch is turned off, single signalin
20. PERFENH_PS_CMTIMEOUT
similar event 2F measurement rep
mode expires. When this switch is
21. PERFENH_SPEC_PRD_HHO
requirements, when the time dela
triggered immediately. When this
22. PERFENH_BASE_COV_BE_
DCH to DCH in the uplink when th
23. PERFENH_RRC_CELL_HSU
not support HSUPA due to the hig
connection setup.
24. PERFENH_RRC_CELL_HSD
does not support HSDPA due to h
the RRC connection setup.
25. PERFENH_CELL_TTI2MS_C
Iub interface a message indicating
be carried on the E-DCH in the up
26. PERFENH_OLPC_TBSIZE0_
frames if the UE uses the followin
TB number is not 0, and BetaD/B
27. PERFENH_UU_P2D_F2D_M
the message size reduction functi
28. PERFENH_DYC_INIBITRATE
takes effect and cooperates with t
parameter when the UE has set u
speed channel or reduce the bit ra
downlink initial bit rate of a PS BE
29. PERFENH_RLRESETUP_GU
AMR+PS BE combined services,
30. PERFENH_RLRESETUP_PR
preempted if cell resources are in
and AMR+PS BE combined servi
GUI Value Range: PERFENH_CO
PERFENH_AMRC_NACK_SWIT
PERFENH_FORCE_AMR_INTER
PERFENH_RB_MAPPING_OPT_
PERFENH_PS_CMTIMEOUT_UP
Parameter ID NE MML Command Feature Feature Name
ID
PERFENH_RRC_CELL_HSDPA_
PERFENH_DYC_INIBITRATE_M
Unit: None
Actual Value Range:
PERFENH_COMM_PLMN_HO_A
PERFENH_AMRC_NACK_SWIT
PERFENH_FORCE_AMR_INTER
PERFENH_RB_MAPPING_OPT_
PERFENH_PS_CMTIMEOUT_UP
PERFENH_RRC_CELL_HSDPA_
PERFENH_UU_P2D_F2D_MSG_
PERFENH_DYC_INIBITRATE_M
Default Value:
PERFENH_COMM_PLMN_HO_A
C_NACK_SWITCH:0,PERFENH_
OUT_SWITCH:0,PERFENH_INA
WITCH:0,PERFENH_U2L_REDIR
RD_HHO_DELAY_TIME_SWITC
_CHG_OPT_SWITCH:1,PERFEN
ESETUP_PREEMPT_SWITCH:0
22. PERFENH_BASE_COV_BE_
DCH to DCH in the uplink when th
23. PERFENH_RRC_CELL_HSU
not support HSUPA due to the hig
connection setup.
24. PERFENH_RRC_CELL_HSD
does not support HSDPA due to h
the RRC connection setup.
25. PERFENH_CELL_TTI2MS_C
Iub interface a message indicating
be carried on the E-DCH in the up
26. PERFENH_OLPC_TBSIZE0_
frames if the UE uses the followin
TB number is not 0, and BetaD/B
27. PERFENH_UU_P2D_F2D_M
the message size reduction functi
28. PERFENH_DYC_INIBITRATE
takes effect and cooperates with t
parameter when the UE has set u
speed channel or reduce the bit ra
downlink initial bit rate of a PS BE
29. PERFENH_RLRESETUP_GU
AMR+PS BE combined services,
30. PERFENH_RLRESETUP_PR
preempted if cell resources are in
and AMR+PS BE combined servi
GUI Value Range: PERFENH_CO
PERFENH_AMRC_NACK_SWIT
PERFENH_FORCE_AMR_INTER
PERFENH_RB_MAPPING_OPT_
PERFENH_PS_CMTIMEOUT_UP
PERFENH_RRC_CELL_HSDPA_
PERFENH_DYC_INIBITRATE_M
Unit: None
Actual Value Range:
PERFENH_COMM_PLMN_HO_A
PERFENH_AMRC_NACK_SWIT
PERFENH_FORCE_AMR_INTER
PERFENH_RB_MAPPING_OPT_
PERFENH_PS_CMTIMEOUT_UP
PERFENH_RRC_CELL_HSDPA_
PERFENH_UU_P2D_F2D_MSG_
PERFENH_DYC_INIBITRATE_M
Parameter ID NE MML Command Feature Feature Name
ID
Default Value:
PERFENH_COMM_PLMN_HO_A
C_NACK_SWITCH:0,PERFENH_
OUT_SWITCH:0,PERFENH_INA
WITCH:0,PERFENH_U2L_REDIR
RD_HHO_DELAY_TIME_SWITC
_CHG_OPT_SWITCH:1,PERFEN
ESETUP_PREEMPT_SWITCH:0
InactF2PStateTransTim BSC69 SET WRFD- UE State in Meaning: Timer for the UE inactiv
er 00 UUESTATETRANST 010202 Connected transition.
IMER
Mode (CELL- GUI Value Range: 1~64800
DCH, CELL- Unit: s
PCH, URA-
PCH, CELL- Actual Value Range: 1~64800
FACH) Default Value: 10
InactF2PStateTransTim BSC69 SET WRFD- UE State in Meaning: Timer for the UE inactiv
er 10 UUESTATETRANST 010202 Connected transition.
IMER
Mode (CELL- GUI Value Range: 1~64800
DCH, CELL- Unit: s
PCH, URA-
PCH, CELL- Actual Value Range: 1~64800
FACH) Default Value: 10
InactF2PStateTransTim BSC69 ADD WRFD- UE State in Meaning: Timer for the UE inactiv
er 00 UCELLUESTATETR 010202 Connected transition.
ANS
Mode (CELL- GUI Value Range: 1~64800
MOD
UCELLUESTATETR DCH, CELL- Unit: s
ANS PCH, URA-
PCH, CELL- Actual Value Range: 1~64800
FACH) Default Value: 10
InactF2PStateTransTim BSC69 ADD WRFD- UE State in Meaning: Timer for the UE inactiv
er 10 UCELLUESTATETR 010202 Connected transition.
ANS
Mode (CELL- GUI Value Range: 1~64800
MOD
UCELLUESTATETR DCH, CELL- Unit: s
ANS PCH, URA-
PCH, CELL- Actual Value Range: 1~64800
FACH) Default Value: 10
CellReSelectTimer BSC69 SET WRFD- UE State in Meaning: Length of the timer dete
00 UUESTATETRANST 010202 Connected determines that the UE has perfo
IMER
Mode (CELL- state by sending the UE a CELL_
DCH, CELL- GUI Value Range: 1~65535
PCH, URA- Unit: s
Actual Value Range: 1~65535
Parameter ID NE MML Command Feature Feature Name
ID
CellReSelectTimer BSC69 SET WRFD- UE State in Meaning: Length of the timer dete
10 UUESTATETRANST 010202 Connected determines that the UE has perfo
IMER
Mode (CELL- state by sending the UE a CELL_
DCH, CELL- GUI Value Range: 1~65535
PCH, URA- Unit: s
PCH, CELL-
FACH) Actual Value Range: 1~65535
Default Value: 180
CellReSelectCounter BSC69 SET WRFD- UE State in Meaning: Threshold for the numb
00 UUESTATETRANS 010202 Connected frequent cell reselections. This pe
Mode (CELL- state by sending the UE a CELL_
DCH, CELL- GUI Value Range: 1~65535
PCH, URA- Unit: None
PCH, CELL-
FACH) Actual Value Range: 1~65535
Default Value: 9
CellReSelectCounter BSC69 SET WRFD- UE State in Meaning: Threshold for the numb
10 UUESTATETRANS 010202 Connected frequent cell reselections. This pe
Mode (CELL- state by sending the UE a CELL_
DCH, CELL- GUI Value Range: 1~65535
PCH, URA- Unit: None
PCH, CELL-
FACH) Actual Value Range: 1~65535
Default Value: 9
5) CS_RLFAIL_RRCSETUP_STA
1: This switch is turned on. If radio
drops.
0: This switch is turned off. If radio
call drops.
6) PS_INACT_NOTREL_FOR_CS
1: This switch is turned on. The R
session and one or more PS sess
0: This switch is turned off. The R
7) CS_CALL_DROP_DEFINITION
1: This switch is turned on. The R
The RNC releases a CS service.
The RNC receives an IU RELEAS
0: This switch is turned off. The R
8) PS_CALL_DROP_DEFINITION
1: This switch is turned on. The R
The RNC releases a PS service.
The RNC receives an IU RELEAS
0: This switch is turned off. The R
9) RNC_U2U_SWITCH (Switch fo
1: This switch is turned on. The R
0: This switch is turned off. The R
10) CCH_ABNORMOLREL_CAU
1: This switch is turned on. An ab
0: This switch is turned off. An ab
11) INTERRAT2U_RESUME_PS
1: This switch is turned on. The R
0: This switch is turned off. The R
12) UE_TRB_RESET_IOT_SWIT
1: This switch is turned on. After a
containing physical layer informat
UE.The UE will respond with one
RECONFIGURATION COMPLET
0: This switch is turned off. After a
normal procedure.
13) CUC_CMP_NO_ACTIVE_CF
1: This switch is turned on. The R
CONFIRM message.
0: This switch is turned off. The R
14) RAB_DL_BITRATE_MOD_SW
1: This switch is turned on. The R
Parameter ID NE MML Command Feature Feature Name
ID
15) RAB_WAIT_IUUP_INIT_RES
1: This switch is turned on. The R
0: This switch is turned off. The R
16) RNC_RDY_FOR_INTERRAT
1: This switch is turned on. When
(1)Upon receiving a RANAP_REL
(2)After the eNodeB initiates a RI
0: This switch is turned off. When
(1)Upon receiving a RANAP_REL
(2)After the eNodeB initiates a RI
This parameter is an advanced pa
GUI Value Range: FACH_DCCH_
PS_INACT_NOTREL_FOR_CSP
RNC_U2U_SWITCH, INTERRAT
Unit: None
Actual Value Range: FACH_DCC
PS_INACT_NOTREL_FOR_CSP
RNC_U2U_SWITCH, INTERRAT
Default Value:
FACH_DCCH_CONG_CTRL_SW
SPS_SWITCH:0,RAB_DL_BITRA
TERRAT2U_RESUME_PS_ASAP
BeF2HTvmThd BSC69 SET WRFD- HSDPA State Meaning: This parameter specifie
00 UUESTATETRANS 010611 Transition the "SET UUESTATETRANS" co
11 "BeH2FTvmThd" parameter as th
GUI Value Range: D16, D32, D64
Unit: byte
Actual Value Range: 16, 32, 64, 1
Default Value: D256
BeF2HTvmThd BSC69 SET WRFD- HSDPA State Meaning: This parameter specifie
10 UUESTATETRANS 010611 Transition the "SET UUESTATETRANS" co
11 "BeH2FTvmThd" parameter as th
GUI Value Range: D16, D32, D64
Unit: byte
Actual Value Range: 16, 32, 64, 1
Default Value: D256
BeF2HTvmTimeToTrig BSC69 SET WRFD- HSDPA State Meaning: This parameter specifie
00 UUESTATETRANS 010611 Transition GUI Value Range: D0, D10, D20,
11 Unit: ms
Actual Value Range: 0, 10, 20, 40
Default Value: D0
BeF2HTvmTimeToTrig BSC69 SET WRFD- HSDPA State Meaning: This parameter specifie
10 UUESTATETRANS 010611 Transition GUI Value Range: D0, D10, D20,
11 Unit: ms
Actual Value Range: 0, 10, 20, 40
Default Value: D0
EdchRateAdjustSet BSC69 SET WRFD- Dynamic Meaning: Data rate set for adjusti
00 UEDCHRATEADJU 021101 Channel
STSET GUI Value Range: RATE_8KBPS
Configuration RATE_5440KBPS, RATE_11480
Control (DCCC) Unit: None
Parameter ID NE MML Command Feature Feature Name
ID
EdchRateAdjustSet BSC69 SET WRFD- Dynamic Meaning: Data rate set for adjusti
10 UEDCHRATEADJU 021101 Channel
STSET GUI Value Range: RATE_8KBPS
WRFD- Configuration RATE_5440KBPS, RATE_11480
010612 Control (DCCC) Unit: None
08 HSUPA DCCC Actual Value Range: 8, 16, 32, 64
Default Value:
RATE_8KBPS:0,RATE_16KBPS:
KBPS:0,RATE_11480KBPS:0
BasedTimeF2DThd BSC69 SET WRFD- UE State in Meaning: Time threshold for F2D
00 UUESTATETRANS 010202 Connected exceeded, an F2D state transition
Mode (CELL- takes effect only for PS BE servic
DCH, CELL- GUI Value Range: 0;20~250
PCH, URA- Unit: 0.1s
PCH, CELL-
FACH) Actual Value Range: 0, 2~25
Default Value: 0
BasedTimeF2DThd BSC69 SET WRFD- UE State in Meaning: Time threshold for F2D
10 UUESTATETRANS 010202 Connected exceeded, an F2D state transition
Mode (CELL- takes effect only for PS BE servic
DCH, CELL- GUI Value Range: 0;20~250
PCH, URA- Unit: 0.1s
PCH, CELL-
Actual Value Range: 0, 2~25
FACH)
Default Value: 0
BasedTimeF2DPT BSC69 SET WRFD- UE State in Meaning: When an F2D state tran
00 UUESTATETRANS 010202 Connected volume or throughput is not 0 with
Mode (CELL- related inactive timer.
DCH, CELL- GUI Value Range: 0~240
PCH, URA- Unit: s
PCH, CELL-
Actual Value Range: 0~240
FACH)
Default Value: 30
BasedTimeF2DPT BSC69 SET WRFD- UE State in Meaning: When an F2D state tran
10 UUESTATETRANS 010202 Connected volume or throughput is not 0 with
Mode (CELL- related inactive timer.
DCH, CELL- GUI Value Range: 0~240
PCH, URA- Unit: s
PCH, CELL-
FACH) Actual Value Range: 0~240
Default Value: 30
TimerPoll BSC69 ADD UTYPRABRLC WRFD- Logical Channel Meaning: Maximum time of waitin
00 MOD UTYPRABRLC 020900 Management polling PDU. The TX end retransm
GUI Value Range: D10, D20, D30
D360, D370, D380, D390, D400,
Unit: ms
Actual Value Range: 10, 20, 30, 4
480, 490, 500, 510, 520, 530, 540
Default Value: None
TimerPoll BSC69 ADD UTYPRABRLC WRFD- Logical Channel Meaning: Maximum time of waitin
10 MOD UTYPRABRLC 020900 Management polling PDU. The TX end retransm
GUI Value Range: D10, D20, D30
D360, D370, D380, D390, D400,
Unit: ms
Actual Value Range: 10, 20, 30, 4
480, 490, 500, 510, 520, 530, 540
Default Value: None
BasedTimeF2DPTAT BSC69 SET None None Meaning: Pending time for the F2
00 UUESTATETRANS transition based on data transmis
GUI Value Range: 0~15
Unit: s
Actual Value Range: 0~15
Default Value: 2
BasedTimeF2DPTAT BSC69 SET None None Meaning: Pending time for the F2
10 UUESTATETRANS transition based on data transmis
GUI Value Range: 0~15
Unit: s
Actual Value Range: 0~15
Default Value: 2
Unit: None
Actual Value Range:
RESERVED_SWITCH_11_BIT1,
RESERVED_SWITCH_11_BIT8,
RESERVED_SWITCH_11_BIT15
RESERVED_SWITCH_11_BIT17
RESERVED_SWITCH_11_BIT24
RESERVED_SWITCH_11_BIT31
Default Value:
RESERVED_SWITCH_11_BIT1:0
ESERVED_SWITCH_11_BIT8:0,
4:0,RESERVED_SWITCH_11_BI
1_BIT21:0,RESERVED_SWITCH
TCH_11_BIT28:0,RESERVED_S
F2DStateTransTCPPort BSC69 SET None None Meaning: Number of the TCP por
No 00 UDPUCFGDATA transition, the RNC does not susp
GUI Value Range: 0~65535
Unit: None
Actual Value Range: 0~65535
Parameter ID NE MML Command Feature Feature Name
ID
Default Value: 80
F2DStateTransTCPPort BSC69 SET None None Meaning: Number of the TCP por
No 10 UDPUCFGDATA transition, the RNC does not susp
GUI Value Range: 0~65535
Unit: None
Actual Value Range: 0~65535
Default Value: 80
DlBeH2DInitialRate BSC69 SET UFRC WRFD- HSDPA Meaning: DL initial access rate us
00 010610 Introduction GUI Value Range: D8, D16, D32,
Package Unit: kbit/s
Actual Value Range: 8, 16, 32, 64
Default Value: D128
DlBeH2DInitialRate BSC69 SET UFRC WRFD- HSDPA Meaning: DL initial access rate us
10 010610 Introduction GUI Value Range: D8, D16, D32,
Package Unit: kbit/s
Actual Value Range: 8, 16, 32, 64
Default Value: D128
MaxAllowedUlTxPower BSC69 ADD WRFD- Intra RNC Cell Meaning: The maximum allowed
00 UCELLSELRESEL 010801 Update GUI Value Range: -50~33
MOD
UCELLSELRESEL WRFD- Inter RNC Cell Unit: dBm
010802 Update Actual Value Range: -50~33
Default Value: 24
MaxAllowedUlTxPower BSC69 ADD WRFD- Intra RNC Cell Meaning: The maximum allowed
10 UCELLSELRESEL 010801 Update GUI Value Range: -50~33
MOD
UCELLSELRESEL WRFD- Inter RNC Cell Unit: dBm
010802 Update Actual Value Range: -50~33
Default Value: 24
RrcRscpPeriodTimer BSC69 SET WRFD- TTI Switch for Meaning: Interval for UEs to repo
00 UCHLQUALITYEVA 010690 BE Services
LUATE GUI Value Range: D250, D500, D
Based on Unit: ms
Coverage
Actual Value Range: 250, 500, 10
Default Value: D500
RrcRscpPeriodTimer BSC69 SET WRFD- TTI Switch for Meaning: Interval for UEs to repo
10 UCHLQUALITYEVA 010690 BE Services
LUATE GUI Value Range: D250, D500, D
Based on Unit: ms
Coverage
Actual Value Range: 250, 500, 10
Default Value: D500
RabRscpPeriodTimer BSC69 SET WRFD- TTI Switch for Meaning: Interval for UEs to repo
00 UCHLQUALITYEVA 010690 BE Services
LUATE GUI Value Range: D250, D500, D
Unit: ms
Parameter ID NE MML Command Feature Feature Name
ID
RabRscpPeriodTimer BSC69 SET WRFD- TTI Switch for Meaning: Interval for UEs to repo
10 UCHLQUALITYEVA 010690 BE Services
LUATE GUI Value Range: D250, D500, D
WRFD- Based on Unit: ms
020400 Coverage
Actual Value Range: 250, 500, 10
DRD
Introduction Default Value: D2000
Package
EcN0EffectTime BSC69 ADD UCELLFRC WRFD- 3.4/6.8/13.6/27. Meaning: Time period for valid Ec
00 MOD UCELLFRC 010510 2Kbps RRC RSCP.
WRFD- Connection and GUI Value Range: 0~65535
010690 Radio Access Unit: ms
WRFD- Bearer
Establishment Actual Value Range: 0~65535
010507 Default Value: 5000
and Release
WRFD-
150232 TTI Switch for
BE Services
WRFD-
Based on
010612 Coverage
WRFD- Rate
020400 Negotiation at
Parameter ID NE MML Command Feature Feature Name
ID
Admission
Control
Multiband Direct
Retry Based on
UE Location
HSUPA
Introduction
Package
DRD
Introduction
Package
EcN0EffectTime BSC69 ADD UCELLFRC WRFD- 3.4/6.8/13.6/27. Meaning: Time period for valid Ec
10 MOD UCELLFRC 010510 2Kbps RRC RSCP.
WRFD- Connection and GUI Value Range: 0~65535
010690 Radio Access Unit: ms
WRFD- Bearer
Establishment Actual Value Range: 0~65535
010507 Default Value: 5000
and Release
WRFD-
150232 TTI Switch for
BE Services
WRFD- Based on
010612 Coverage
WRFD- Rate
020400 Negotiation at
Admission
Control
Multiband Direct
Retry Based on
UE Location
HSUPA
Introduction
Package
DRD
Introduction
Package
TvmThdForSmartP2D BSC69 SET WRFD- UE State in Meaning: Load threshold for smar
00 UUESTATETRANS 010202 Connected GUI Value Range: 0~65535
Mode (CELL- Unit: 10byte
DCH, CELL-
PCH, URA- Actual Value Range: 0~655350
PCH, CELL- Default Value: 51
FACH)
TvmThdForSmartP2D BSC69 SET WRFD- UE State in Meaning: Load threshold for smar
10 UUESTATETRANS 010202 Connected GUI Value Range: 0~65535
Mode (CELL- Unit: 10byte
DCH, CELL-
PCH, URA- Actual Value Range: 0~655350
PCH, CELL- Default Value: 51
FACH)
14)FACH_RB_RECFG_FAIL_SP
Whether the RNC releases a UE'
1: This switch is turned on. The R
0: This switch is turned off. The R
15)WBAMR_HHO_FAIL_ROLLBA
Whether RNC performs rollback o
1: This switch is turned on. The R
Otherwise, some UEs experience
0: This switch is turned off. The R
16)SEAMLESS_CRYSTAL_VOIC
Whether the RNC-level seamless
1: This switch is set to on. The RN
0: This switch is set to off. The RN
17)CS_RB_PRI_MC_SWITCH
Switch controlling the CS RB setu
1: When this switch is set to on fo
0: When this switch is set to off, th
18)L2U_SRVCC_PS_TIMEOUT_
Whether to support the incoming
1: When this switch is set to on, th
RELOCATION REQUEST messa
0: When this switch is set to off, th
For details, see 3GPP TS 23.216
19)CRYSTAL_VOICE_DEEPCOV
Whether the RNC-level Crystal Vo
1: This switch is set to on. The RN
0: This switch is set to off. The RN
20)LOAD_BASED_P2D_SWITCH
Whether the load- and Ec/N0-bas
1: Indicates that this switch is set
(1)The actual uplink cell load ente
the "ActualloadStateForP2D" and
(2) The Ec/N0 is greater than or e
0: Indicates that this switch is set
21)PRIMOPER_NONROAM_USE
Whether the CN-initiated service
1: Indicates that this switch is set
0: Indicates that this switch is set
22)PS_R99_BLER_STAT_OPT_S
Whether the RNC optimizes the m
Parameter ID NE MML Command Feature Feature Name
ID
PS_R99_BLER_STAT_OPT_SW
RRC_CONN_SETUP_MSG_ENH
Unit: None
Actual Value Range:
INTERRAT_LOAD_SINGLE_RPT
INTERRAT_LOAD_REPORT_FR
UL_EVQI_SWITCH,
DL_EVQI_SWITCH,
VIDEO_RATE_ADAPTION_SWIT
VOIP_MANAGE_SWITCH,
DIFF_SERVICE_ON_TERMINAL
APP_GRP_RES_RSV_SWITCH,
RIM_ON_ECO_SWITCH,
PRIMOPER_NONROAM_USER_
SRBCHG_DRD_FAST_RB_SETU
SRBNOCHG_DRD_FAST_RB_S
FACH_RB_RECFG_FAIL_SPEC
WBAMR_HHO_FAIL_ROLLBACK
EXTD_LAC_PAGING_SWITCH,
TCP_PROXY_SWITCH,
SEAMLESS_CRYSTAL_VOICE_
CS_RB_PRI_MC_SWITCH,
L2U_SRVCC_PS_TIMEOUT_CS
CRYSTAL_VOICE_DEEPCOVER
LOAD_BASED_P2D_SWITCH,
PS_R99_BLER_STAT_OPT_SW
STATE_FACH_CONSISTENT_O
D2P_RECFG_REEST_SWITCH,
IMPVD_UL_COVER_FOR_SRB_
UL_DT_SAI_PLMN_CMP_SWITC
RRC_CONN_SETUP_MSG_ENH
UE_UDA_CAP_QUERY_SWITCH
UDA_SWITCH
Default Value:
INTERRAT_LOAD_SINGLE_RPT
N_TERMINAL_SWITCH:0,APP_G
ACH_RB_RECFG_FAIL_SPEC_C
CC_PS_TIMEOUT_CS_RELOC_
WITCH:0,IMPVD_UL_COVER_F
Parameter ID NE MML Command Feature Feature Name
ID
19)CRYSTAL_VOICE_DEEPCOV
Whether the RNC-level Crystal Vo
1: This switch is set to on. The RN
0: This switch is set to off. The RN
20)LOAD_BASED_P2D_SWITCH
Whether the load- and Ec/N0-bas
1: Indicates that this switch is set
(1)The actual uplink cell load ente
the "ActualloadStateForP2D" and
(2) The Ec/N0 is greater than or e
0: Indicates that this switch is set
21)PRIMOPER_NONROAM_USE
Whether the CN-initiated service
1: Indicates that this switch is set
0: Indicates that this switch is set
22)PS_R99_BLER_STAT_OPT_S
Whether the RNC optimizes the m
1: Indicates that this switch is set
0: Indicates that this switch is set
23)STATE_FACH_CONSISTENT
Whether to enable the state cons
1: Indicates that this switch is set
state. This prevents state inconsis
0: Indicates that this switch is set
This switch is set to OFF by defau
24)D2P_RECFG_REEST_SWITC
Whether the RNC triggers a D2P
1: Indicates that this switch is set
0: Indicates that this switch is set
This switch is set to OFF by defau
25)IMPVD_UL_COVER_FOR_SR
Whether to enable the Improved U
1: Indicates that this switch is set
0: Indicates that this switch is set
26)UL_DT_SAI_PLMN_CMP_SW
Controls the PLMN in the SAI info
1: Indicates that this switch is set
0: Indicates that this switch is set
27)RRC_CONN_SETUP_MSG_E
Whether the enhancement of RRC
Parameter ID NE MML Command Feature Feature Name
ID
LOAD_BASED_P2D_SWITCH,
PS_R99_BLER_STAT_OPT_SW
STATE_FACH_CONSISTENT_O
D2P_RECFG_REEST_SWITCH,
IMPVD_UL_COVER_FOR_SRB_
UL_DT_SAI_PLMN_CMP_SWITC
RRC_CONN_SETUP_MSG_ENH
UE_UDA_CAP_QUERY_SWITCH
UDA_SWITCH
Default Value:
INTERRAT_LOAD_SINGLE_RPT
N_TERMINAL_SWITCH:0,APP_G
ACH_RB_RECFG_FAIL_SPEC_C
CC_PS_TIMEOUT_CS_RELOC_
WITCH:0,IMPVD_UL_COVER_F
ActualloadStateForP2D BSC69 SET WRFD- UE State in Meaning: P2D uplink actual servic
00 UUESTATETRANS 010202 Connected function take effect is satisfied.
Mode (CELL- GUI Value Range: UL_LIGHT_ST
DCH, CELL- Unit: None
PCH, URA-
PCH, CELL- Actual Value Range:
FACH) UL_LIGHT_STATE, UL_NORMA
UL_LOADED_STATE,
UL_HEAVY_STATE, UL_OVERR
Default Value: UL_NORMAL_STA
ActualloadStateForP2D BSC69 SET WRFD- UE State in Meaning: P2D uplink actual servic
10 UUESTATETRANS 010202 Connected function take effect is satisfied.
Mode (CELL- GUI Value Range: UL_LIGHT_ST
DCH, CELL- Unit: None
PCH, URA-
PCH, CELL- Actual Value Range:
FACH) UL_LIGHT_STATE, UL_NORMA
UL_LOADED_STATE,
UL_HEAVY_STATE, UL_OVERR
Default Value: UL_NORMAL_STA
DL_LOADED_STATE,
DL_HEAVY_STATE, DL_OVERR
Default Value: DL_NORMAL_STA
P2DEcNoThd BSC69 SET UFRC WRFD- UE State in Meaning: P2D state transition Ec/
00 010202 Connected take effect is satisfied.
Mode (CELL- GUI Value Range: 0~50
DCH, CELL- Unit: 0.5dB
PCH, URA-
Actual Value Range: -24.5~0.5(A
PCH, CELL-
FACH) Default Value: 31
P2DEcNoThd BSC69 SET UFRC WRFD- UE State in Meaning: P2D state transition Ec/
10 010202 Connected take effect is satisfied.
Mode (CELL- GUI Value Range: 0~50
DCH, CELL- Unit: 0.5dB
PCH, URA-
Actual Value Range: -24.5~0.5(A
PCH, CELL-
FACH) Default Value: 31
BeCpc2FStateTransTim BSC69 SET WRFD- CPC - DTX / Meaning: Timer for state transition
er 00 UUESTATETRANST 010686 DRX
IMER GUI Value Range: 1~65535
WRFD- CPC - HS- Unit: s
010687 SCCH less Actual Value Range: 1~65535
WRFD- operation Default Value: 5
010611 HSDPA State
11 Transition
WRFD- UE State in
010202 Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
Parameter ID NE MML Command Feature Feature Name
ID
BeCpc2FStateTransTim BSC69 SET WRFD- CPC - DTX / Meaning: Timer for state transition
er 10 UUESTATETRANST 010686 DRX
IMER GUI Value Range: 1~65535
WRFD- CPC - HS- Unit: s
010687 SCCH less Actual Value Range: 1~65535
WRFD- operation Default Value: 5
010611 HSDPA State
11 Transition
WRFD- UE State in
010202 Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
BeCpc2FStateTransTim BSC69 ADD WRFD- CPC - DTX / Meaning: Timer for state transition
er 00 UCELLUESTATETR 010686 DRX
ANS GUI Value Range: 1~65535
MOD WRFD- CPC - HS- Unit: s
UCELLUESTATETR 010687 SCCH less Actual Value Range: 1~65535
ANS WRFD- operation Default Value: 5
010611 HSDPA State
11 Transition
WRFD- UE State in
010202 Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
BeCpc2FStateTransTim BSC69 ADD WRFD- CPC - DTX / Meaning: Timer for state transition
er 10 UCELLUESTATETR 010686 DRX
ANS GUI Value Range: 1~65535
MOD WRFD- CPC - HS- Unit: s
UCELLUESTATETR 010687 SCCH less Actual Value Range: 1~65535
ANS WRFD- operation Default Value: 5
010611 HSDPA State
11 Transition
WRFD- UE State in
010202 Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
Parameter ID NE MML Command Feature Feature Name
ID
RtCpc2FStateTransTim BSC69 SET WRFD- CPC - DTX / Meaning: Timer for state transition
er 00 UUESTATETRANST 010686 DRX
IMER GUI Value Range: 1~65535
WRFD- CPC - HS- Unit: s
010687 SCCH less Actual Value Range: 1~65535
WRFD- operation Default Value: 180
010611 HSDPA State
11 Transition
WRFD- UE State in
010202 Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
RtCpc2FStateTransTim BSC69 SET WRFD- CPC - DTX / Meaning: Timer for state transition
er 10 UUESTATETRANST 010686 DRX
IMER GUI Value Range: 1~65535
WRFD- CPC - HS- Unit: s
010687 SCCH less Actual Value Range: 1~65535
WRFD- operation Default Value: 180
010611 HSDPA State
11 Transition
WRFD- UE State in
010202 Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
BeD2EFachStateTransT BSC69 SET WRFD- UE State in Meaning: Timer for state transition
imer 00 UUESTATETRANST 010202 Connected
IMER GUI Value Range: 1~65535
WRFD- Mode (CELL- Unit: s
010611 DCH, CELL- Actual Value Range: 1~65535
11 PCH, URA-
Default Value: 5
WRFD- PCH, CELL-
010688 FACH)
HSDPA State
Transition
Downlink
Enhanced
CELL_FACH
BeD2EFachStateTransT BSC69 SET WRFD- UE State in Meaning: Timer for state transition
imer 10 UUESTATETRANST 010202 Connected
IMER GUI Value Range: 1~65535
Mode (CELL-
Parameter ID NE MML Command Feature Feature Name
ID
BeD2EFachStateTransT BSC69 ADD WRFD- UE State in Meaning: Timer for state transition
imer 00 UCELLUESTATETR 010202 Connected
ANS GUI Value Range: 1~65535
MOD WRFD- Mode (CELL- Unit: s
UCELLUESTATETR 010611 DCH, CELL- Actual Value Range: 1~65535
ANS 11 PCH, URA-
Default Value: 5
WRFD- PCH, CELL-
010688 FACH)
HSDPA State
Transition
Downlink
Enhanced
CELL_FACH
BeD2EFachStateTransT BSC69 ADD WRFD- UE State in Meaning: Timer for state transition
imer 10 UCELLUESTATETR 010202 Connected
ANS GUI Value Range: 1~65535
MOD WRFD- Mode (CELL- Unit: s
UCELLUESTATETR 010611 DCH, CELL- Actual Value Range: 1~65535
ANS 11 PCH, URA-
Default Value: 5
WRFD- PCH, CELL-
010688 FACH)
HSDPA State
Transition
Downlink
Enhanced
CELL_FACH
BeH2EFachStateTransT BSC69 ADD WRFD- UE State in Meaning: Timer for state transition
imer 00 UCELLUESTATETR 010202 Connected
ANS GUI Value Range: 1~65535
MOD WRFD- Mode (CELL- Unit: s
UCELLUESTATETR 010611 DCH, CELL- Actual Value Range: 1~65535
ANS 11 PCH, URA-
Default Value: 5
WRFD- PCH, CELL-
010688 FACH)
HSDPA State
Transition
Parameter ID NE MML Command Feature Feature Name
ID
Downlink
Enhanced
CELL_FACH
BeH2EFachStateTransT BSC69 ADD WRFD- UE State in Meaning: Timer for state transition
imer 10 UCELLUESTATETR 010202 Connected
ANS GUI Value Range: 1~65535
MOD WRFD- Mode (CELL- Unit: s
UCELLUESTATETR 010611 DCH, CELL- Actual Value Range: 1~65535
ANS 11 PCH, URA-
Default Value: 5
WRFD- PCH, CELL-
010688 FACH)
HSDPA State
Transition
Downlink
Enhanced
CELL_FACH
RtDH2EFachStateTrans BSC69 SET WRFD- UE State in Meaning: Timer for state transition
Timer 00 UUESTATETRANST 010202 Connected
IMER GUI Value Range: 1~65535
WRFD- Mode (CELL- Unit: s
010611 DCH, CELL- Actual Value Range: 1~65535
11 PCH, URA-
Default Value: 180
WRFD- PCH, CELL-
010688 FACH)
HSDPA State
Transition
Downlink
Enhanced
CELL_FACH
RtDH2EFachStateTrans BSC69 SET WRFD- UE State in Meaning: Timer for state transition
Timer 10 UUESTATETRANST 010202 Connected
IMER GUI Value Range: 1~65535
WRFD- Mode (CELL- Unit: s
010611 DCH, CELL- Actual Value Range: 1~65535
11 PCH, URA-
Default Value: 180
WRFD- PCH, CELL-
010688 FACH)
HSDPA State
Transition
Downlink
Enhanced
CELL_FACH
BeCpc2EFachStateTran BSC69 SET WRFD- CPC - DTX / Meaning: Timer for state transition
sTimer 00 UUESTATETRANST 010686 DRX
IMER GUI Value Range: 1~65535
Unit: s
Parameter ID NE MML Command Feature Feature Name
ID
BeCpc2EFachStateTran BSC69 SET WRFD- CPC - DTX / Meaning: Timer for state transition
sTimer 10 UUESTATETRANST 010686 DRX
IMER GUI Value Range: 1~65535
WRFD- CPC - HS- Unit: s
010687 SCCH less Actual Value Range: 1~65535
WRFD- operation Default Value: 5
010611 HSDPA State
11 Transition
WRFD- Downlink
010688 Enhanced
WRFD- CELL_FACH
010202 UE State in
Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
RtCpc2EFachStateTran BSC69 SET WRFD- CPC - DTX / Meaning: Timer for state transition
sTimer 00 UUESTATETRANST 010686 DRX
IMER GUI Value Range: 1~65535
WRFD- CPC - HS- Unit: s
010687 SCCH less Actual Value Range: 1~65535
WRFD- operation Default Value: 180
010611 HSDPA State
11 Transition
WRFD- Downlink
010688 Enhanced
WRFD- CELL_FACH
010202
Parameter ID NE MML Command Feature Feature Name
ID
UE State in
Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
RtCpc2EFachStateTran BSC69 SET WRFD- CPC - DTX / Meaning: Timer for state transition
sTimer 10 UUESTATETRANST 010686 DRX
IMER GUI Value Range: 1~65535
WRFD- CPC - HS- Unit: s
010687 SCCH less Actual Value Range: 1~65535
WRFD- operation Default Value: 180
010611 HSDPA State
11 Transition
WRFD- Downlink
010688 Enhanced
WRFD- CELL_FACH
010202 UE State in
Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
BeF2CpcHTvmTimeToT BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
rig 00 UUESTATETRANS 010686 DRX volume variation.
WRFD- CPC - HS- GUI Value Range: D0, D10, D20,
010687 SCCH less Unit: ms
WRFD- operation Actual Value Range: 0, 10, 20, 40
010611 HSDPA State Default Value: D0
11 Transition
WRFD- UE State in
010202 Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
BeF2CpcHTvmTimeToT BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
rig 10 UUESTATETRANS 010686 DRX volume variation.
WRFD- CPC - HS- GUI Value Range: D0, D10, D20,
010687 SCCH less Unit: ms
operation
Parameter ID NE MML Command Feature Feature Name
ID
RtF2CpcTvmTimeToTrig BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
00 UUESTATETRANS 010686 DRX volume variation.
WRFD- CPC - HS- GUI Value Range: D0, D10, D20,
010687 SCCH less Unit: ms
WRFD- operation Actual Value Range: 0, 10, 20, 40
010611 HSDPA State Default Value: D0
11 Transition
WRFD- UE State in
010202 Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
RtF2CpcTvmTimeToTrig BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
10 UUESTATETRANS 010686 DRX volume variation.
WRFD- CPC - HS- GUI Value Range: D0, D10, D20,
010687 SCCH less Unit: ms
WRFD- operation Actual Value Range: 0, 10, 20, 40
010611 HSDPA State Default Value: D0
11 Transition
WRFD- UE State in
010202 Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
BeF2CpcETvmTimeToT BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
rig 00 UUESTATETRANS 010686 DRX variation.
WRFD- CPC - HS- GUI Value Range: D0, D10, D20,
010687 SCCH less Unit: ms
operation Actual Value Range: 0, 10, 20, 40
Parameter ID NE MML Command Feature Feature Name
ID
BeF2CpcETvmTimeToT BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
rig 10 UUESTATETRANS 010686 DRX variation.
WRFD- CPC - HS- GUI Value Range: D0, D10, D20,
010687 SCCH less Unit: ms
WRFD- operation Actual Value Range: 0, 10, 20, 40
010611 HSDPA State Default Value: D0
11 Transition
WRFD- UE State in
010202 Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
BeF2CpcHTvmThd BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
00 UUESTATETRANS 010686 DRX [UCORRMPARA:PERFENHANC
WRFD- CPC - HS- GUI Value Range: D16, D32, D64
010687 SCCH less Unit: byte
WRFD- operation Actual Value Range: 16, 32, 64, 1
010611 HSDPA State Default Value: D512
11 Transition
WRFD- UE State in
010202 Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
BeF2CpcHTvmThd BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
10 UUESTATETRANS 010686 DRX [UCORRMPARA:PERFENHANC
WRFD- CPC - HS- GUI Value Range: D16, D32, D64
010687 SCCH less Unit: byte
operation Actual Value Range: 16, 32, 64, 1
Parameter ID NE MML Command Feature Feature Name
ID
RtF2CpcTvmThd BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
00 UUESTATETRANS 010686 DRX GUI Value Range: D16, D32, D64
WRFD- CPC - HS- Unit: byte
010687 SCCH less Actual Value Range: 16, 32, 64, 1
WRFD- operation
Default Value: D512
010611 HSDPA State
11 Transition
WRFD- UE State in
010202 Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
RtF2CpcTvmThd BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
10 UUESTATETRANS 010686 DRX GUI Value Range: D16, D32, D64
WRFD- CPC - HS- Unit: byte
010687 SCCH less Actual Value Range: 16, 32, 64, 1
WRFD- operation
Default Value: D512
010611 HSDPA State
11 Transition
WRFD- UE State in
010202 Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
BeF2CpcETvmThd BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
00 UUESTATETRANS 010686 DRX [UCORRMPARA:PERFENHANC
WRFD- CPC - HS- GUI Value Range: D16, D32, D64
010687 SCCH less Unit: byte
operation Actual Value Range: 16, 32, 64, 1
Parameter ID NE MML Command Feature Feature Name
ID
BeF2CpcETvmThd BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
10 UUESTATETRANS 010686 DRX [UCORRMPARA:PERFENHANC
WRFD- CPC - HS- GUI Value Range: D16, D32, D64
010687 SCCH less Unit: byte
WRFD- operation Actual Value Range: 16, 32, 64, 1
010611 HSDPA State Default Value: D512
11 Transition
WRFD- UE State in
010202 Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
HSDPA State
Transition
Downlink
Enhanced
CELL_FACH
HSDPA State
Transition
Downlink
Enhanced
CELL_FACH
BeEFach2CpcTvmTime BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
ToTrig 00 UUESTATETRANS 010686 DRX GUI Value Range: D0, D10, D20,
WRFD- CPC - HS- Unit: ms
010687 SCCH less Actual Value Range: 0, 10, 20, 40
WRFD- operation
Default Value: D0
010611 HSDPA State
11 Transition
WRFD- Downlink
010688 Enhanced
WRFD- CELL_FACH
010202 UE State in
Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
BeEFach2CpcTvmTime BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
ToTrig 10 UUESTATETRANS 010686 DRX GUI Value Range: D0, D10, D20,
WRFD- CPC - HS- Unit: ms
010687 SCCH less Actual Value Range: 0, 10, 20, 40
WRFD- operation
Default Value: D0
010611 HSDPA State
11 Transition
WRFD- Downlink
010688 Enhanced
WRFD- CELL_FACH
010202 UE State in
Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
RtEFach2CpcTvmTimeT BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
oTrig 00 UUESTATETRANS 010686 DRX volume variation.
WRFD- CPC - HS- GUI Value Range: D0, D10, D20,
010687 SCCH less Unit: ms
WRFD- operation Actual Value Range: 0, 10, 20, 40
010611 HSDPA State Default Value: D0
11 Transition
WRFD-
010688
Parameter ID NE MML Command Feature Feature Name
ID
WRFD- Downlink
010202 Enhanced
CELL_FACH
UE State in
Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
RtEFach2CpcTvmTimeT BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
oTrig 10 UUESTATETRANS 010686 DRX volume variation.
WRFD- CPC - HS- GUI Value Range: D0, D10, D20,
010687 SCCH less Unit: ms
WRFD- operation Actual Value Range: 0, 10, 20, 40
010611 HSDPA State Default Value: D0
11 Transition
WRFD- Downlink
010688 Enhanced
WRFD- CELL_FACH
010202 UE State in
Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
BeEFach2CpcTvmThd BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
00 UUESTATETRANS 010686 DRX GUI Value Range: D16, D32, D64
WRFD- CPC - HS- Unit: byte
010687 SCCH less Actual Value Range: 16, 32, 64, 1
WRFD- operation
Default Value: D512
010611 HSDPA State
11 Transition
WRFD- Downlink
010688 Enhanced
WRFD- CELL_FACH
010202 UE State in
Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
Parameter ID NE MML Command Feature Feature Name
ID
PCH, CELL-
FACH)
BeEFach2CpcTvmThd BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
10 UUESTATETRANS 010686 DRX GUI Value Range: D16, D32, D64
WRFD- CPC - HS- Unit: byte
010687 SCCH less Actual Value Range: 16, 32, 64, 1
WRFD- operation
Default Value: D512
010611 HSDPA State
11 Transition
WRFD- Downlink
010688 Enhanced
WRFD- CELL_FACH
010202 UE State in
Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
RtEFach2CpcTvmThd BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
00 UUESTATETRANS 010686 DRX GUI Value Range: D16, D32, D64
WRFD- CPC - HS- Unit: byte
010687 SCCH less Actual Value Range: 16, 32, 64, 1
WRFD- operation
Default Value: D512
010611 HSDPA State
11 Transition
WRFD- Downlink
010688 Enhanced
WRFD- CELL_FACH
010202 UE State in
Connected
Mode (CELL-
DCH, CELL-
PCH, URA-
PCH, CELL-
FACH)
RtEFach2CpcTvmThd BSC69 SET WRFD- CPC - DTX / Meaning: This parameter specifie
10 UUESTATETRANS 010686 DRX GUI Value Range: D16, D32, D64
WRFD- CPC - HS- Unit: byte
010687 SCCH less Actual Value Range: 16, 32, 64, 1
operation
Default Value: D512
Parameter ID NE MML Command Feature Feature Name
ID
TthdForSFSTUserIdentif BSC69 SET USTATETIMER WRFD- UE State in Meaning: Timer for determining w
y 00 010202 Connected greater than or equal to this thres
Mode (CELL- GUI Value Range: 0~3600
DCH, CELL- Unit: s
PCH, URA-
PCH, CELL- Actual Value Range: 0~3600
FACH) Default Value: 15
TthdForSFSTUserIdentif BSC69 SET USTATETIMER WRFD- UE State in Meaning: Timer for determining w
y 10 010202 Connected greater than or equal to this thres
Mode (CELL- GUI Value Range: 0~3600
DCH, CELL- Unit: s
PCH, URA-
PCH, CELL- Actual Value Range: 0~3600
FACH) Default Value: 15
PCH, CELL-
FACH)
17. CMP_D2F_RLC_ONESIDE_R
CELL_PCH or URA_PCH (D2P fo
18. CMP_RAB_5_CFG_ROHC_S
configured with the ROHC functio
19. CMP_RAB_6_CFG_ROHC_S
20. CMP_RAB_7_CFG_ROHC_S
21. CMP_RAB_8_CFG_ROHC_S
22. CMP_RAB_9_CFG_ROHC_S
23. CMP_HSUPA_MACD_FLOW
MAC-d flow can be multiplexed.
24. CMP_SMLC_RSLT_MODE_T
PLMN Operator - Target MS serv
25. CMP_F2P_PROCESS_OPTIM
channel reconfiguration procedur
26. CMP_UU_SIB11_SIB12_WIT
cannot promptly read parameters
UCELLMEAS command.
Disuse Statement:This switch CM
Therefore, this switch is not recom
GUI Value Range: CMP_IU_IMS_
CMP_UU_AMR_SID_MUST_CFG
CMP_UU_SERV_CELL_CHG_W
CMP_IU_QOS_ASYMMETRY_IN
CMP_UU_SIB11_SIB12_WITH_1
CMP_RAB_7_CFG_ROHC_SWIT
Unit: None
Actual Value Range: CMP_IU_IM
CMP_IUR_SHO_DIVCTRL_SWIT
CMP_UU_IGNORE_UE_RLC_CA
CMP_UU_SERV_CELL_CHG_W
CMP_RAB_5_CFG_ROHC_SWIT
CMP_SMLC_RSLT_MODE_TYP
Default Value:
CMP_IU_IMS_PROC_AS_NORM
CTRL_SWITCH:0,CMP_UU_ADJ
WITCH:1,CMP_UU_INTRA_FRE
CMP_UU_VOIP_UP_PROC_AS_
MP_RAB_7_CFG_ROHC_SWITC
ZATION_SWITCH:0,CMP_UU_S
26. CMP_UU_SIB11_SIB12_WIT
cannot promptly read parameters
UCELLMEAS command.
Disuse Statement:This switch CM
Therefore, this switch is not recom
GUI Value Range: CMP_IU_IMS_
CMP_UU_AMR_SID_MUST_CFG
CMP_UU_SERV_CELL_CHG_W
CMP_IU_QOS_ASYMMETRY_IN
CMP_UU_SIB11_SIB12_WITH_1
CMP_RAB_7_CFG_ROHC_SWIT
Unit: None
Actual Value Range: CMP_IU_IM
CMP_IUR_SHO_DIVCTRL_SWIT
CMP_UU_IGNORE_UE_RLC_CA
CMP_UU_SERV_CELL_CHG_W
CMP_RAB_5_CFG_ROHC_SWIT
CMP_SMLC_RSLT_MODE_TYP
Default Value:
CMP_IU_IMS_PROC_AS_NORM
CTRL_SWITCH:0,CMP_UU_ADJ
WITCH:1,CMP_UU_INTRA_FRE
CMP_UU_VOIP_UP_PROC_AS_
MP_RAB_7_CFG_ROHC_SWITC
ZATION_SWITCH:0,CMP_UU_S
14)PROC_FOREC_SUCC_COUN
Whether the counters measuring
0: Indicates that this switch is set
1: Indicates that this switch is set
15)FD_SCRI_RCV_IN_RRC_PRO
Whether the RNC performs optim
1: Indicates that this switch is set
the cause value "UE Requested P
connection release indication mes
0: Indicates that this switch is set
16)INNER_CBC_ENCODE_OPT
Whether the built-in CBC uses an
1: Indicates that this switch is set
0: Indicates that this switch is set
17)PLMNID_OPT_IN_RELOC_R
Whether to optimize the PLMN ID
1: Indicates that this switch is set
0: Indicates that this switch is set
18)RB_PROCEDURE_OPT_SWI
Whether the RNC preferentially p
1: Indicates that this switch is set
(1)The RNC does not deactivate D
(2)The RNC rolls back the new co
0: Indicates that this switch is set
19)PLATINUM_TMSI_BROADCA
Whether to optimize the broadcas
1: Indicates that this switch is set
0: Indicates that this switch is set
20)SPECUSER_FAST_RBCFG_
Whether a UE can use the blackli
1: Indicates that this switch is set
0: Indicates that this switch is set
21)RB_SETUP_F2D_CU_CROSS
Whether a RAB is successfully se
RLC unrecoverable error.
1: Indicates that this switch is set
0: Indicates that this switch is set
22)RESTORE_DISCARD_RAB_A
Whether the RNC restores a disc
1: Indicates that this switch is set
Parameter ID NE MML Command Feature Feature Name
ID
RBSETUP_RLREEST_RABSETU
RBSETUP_UEDCHCU_RABSET
PROC_FOREC_SUCC_COUNTE
FD_SCRI_RCV_IN_RRC_PROC
INNER_CBC_ENCODE_OPT_SW
PLMNID_OPT_IN_RELOC_RQD
RB_PROCEDURE_OPT_SWITC
PLATINUM_TMSI_BROADCAST
SPECUSER_FAST_RBCFG_OP
RB_SETUP_F2D_CU_CROSS_O
RESTORE_DISCARD_RAB_ASS
IUR_SIG_E2D_OPT_SWITCH,
RAB_SETUP_ATT_R99_CNT_C
SRB_OVER_HSDPA_CFN_COR
CS_RAB_SETUP_DRD_OPT_SW
SERVICE_QUALITY_MEAS_OPT
IRATHO_HO_OUT_PROCEDUR
IUB_ATM_IP_RL_RECFG_OPT_
ACTIVE_CMCF_FAIL_RL_REES
PFM_PS_CELLDCHUES_PLMN_
RL_REEST_TRIGGER_MSG_OP
Default Value:
F2PU_RESELECT_CU_OVERLA
0,D2F_ABNORMAL_FORCETOF
ST_RABSETUPCNT_CORRECT
NID_OPT_IN_RELOC_RQD_SW
ARD_RAB_ASSIGN_REQ_SWIT
MEAS_OPT_SWITCH:0,IRATHO
R_MSG_OPT_SWITCH:0
FACH_OUTOFSER_OPT_SWITC
P2D_PREPFAIL_OPT_SWITCH,
URA_PCH_RESEL_CU_OPT_SW
D2F_ABNORMAL_FORCETOFA
RLFAIL_OR_TRBRST_D2F_RLR
UE_DCH_CU_RL_REEST_SWIT
CS_RB_SETUP_RL_REEST_SW
PS_RB_SETUP_RL_REEST_SW
RBSETUP_RLREEST_RABSETU
RBSETUP_UEDCHCU_RABSET
PROC_FOREC_SUCC_COUNTE
FD_SCRI_RCV_IN_RRC_PROC
INNER_CBC_ENCODE_OPT_SW
PLMNID_OPT_IN_RELOC_RQD
RB_PROCEDURE_OPT_SWITC
PLATINUM_TMSI_BROADCAST
SPECUSER_FAST_RBCFG_OP
RB_SETUP_F2D_CU_CROSS_O
RESTORE_DISCARD_RAB_ASS
IUR_SIG_E2D_OPT_SWITCH,
RAB_SETUP_ATT_R99_CNT_C
SRB_OVER_HSDPA_CFN_COR
CS_RAB_SETUP_DRD_OPT_SW
SERVICE_QUALITY_MEAS_OPT
IRATHO_HO_OUT_PROCEDUR
IUB_ATM_IP_RL_RECFG_OPT_
ACTIVE_CMCF_FAIL_RL_REES
PFM_PS_CELLDCHUES_PLMN_
RL_REEST_TRIGGER_MSG_OP
Default Value:
F2PU_RESELECT_CU_OVERLA
0,D2F_ABNORMAL_FORCETOF
ST_RABSETUPCNT_CORRECT
NID_OPT_IN_RELOC_RQD_SW
ARD_RAB_ASSIGN_REQ_SWIT
MEAS_OPT_SWITCH:0,IRATHO
R_MSG_OPT_SWITCH:0
PsInactTmrForCon BSC69 SET WRFD- 3.4/6.8/13.6/27. Meaning: When detecting that the
00 UPSINACTTIMER 010510 2Kbps RRC GUI Value Range: 0~14400
Connection and Unit: s
Parameter ID NE MML Command Feature Feature Name
ID
PsInactTmrForCon BSC69 SET WRFD- 3.4/6.8/13.6/27. Meaning: When detecting that the
10 UPSINACTTIMER 010510 2Kbps RRC GUI Value Range: 0~14400
WRFD- Connection and Unit: s
140226 Radio Access
Actual Value Range: 0~14400
Bearer
Establishment Default Value: 20
and Release
Fast Return
from UMTS to
LTE
Establishment
and Release
PsInactTmrForStr BSC69 SET WRFD- UE State in Meaning: When detecting that the
00 UPSINACTTIMER 010202 Connected GUI Value Range: 0~14400
WRFD- Mode (CELL- Unit: s
010510 DCH, CELL-
PCH, URA- Actual Value Range: 0~14400
WRFD- Default Value: 20
140226 PCH, CELL-
FACH)
3.4/6.8/13.6/27.
2Kbps RRC
Connection and
Radio Access
Bearer
Establishment
and Release
Fast Return
from UMTS to
LTE
PsInactTmrForStr BSC69 SET WRFD- UE State in Meaning: When detecting that the
10 UPSINACTTIMER 010202 Connected GUI Value Range: 0~14400
WRFD- Mode (CELL- Unit: s
010510 DCH, CELL-
PCH, URA- Actual Value Range: 0~14400
WRFD- Default Value: 20
140226 PCH, CELL-
FACH)
3.4/6.8/13.6/27.
2Kbps RRC
Connection and
Radio Access
Bearer
Establishment
and Release
Fast Return
from UMTS to
LTE
3.4/6.8/13.6/27.
2Kbps RRC
Connection and
Radio Access
Bearer
Establishment
and Release
Paging UE in
CELL_FACH,
CELL_DCH
State (Type 2)
Inter RNC Cell
Update
Paging UE in
Idle,
CELL_PCH,
URA_PCH State
(Type 1)
URA_PCH State
(Type 1)
Fast Return
from UMTS to
LTE
Radio Access
Bearer
Establishment
and Release
PSInactTmrForImsSig BSC69 SET WRFD- UE State in Meaning: When detecting that the
00 UPSINACTTIMER 010202 Connected GUI Value Range: 0~64800
WRFD- Mode (CELL- Unit: s
010510 DCH, CELL-
PCH, URA- Actual Value Range: 0~64800
PCH, CELL- Default Value: 20
FACH)
3.4/6.8/13.6/27.
2Kbps RRC
Connection and
Radio Access
Bearer
Establishment
and Release
PSInactTmrForImsSig BSC69 SET WRFD- UE State in Meaning: When detecting that the
10 UPSINACTTIMER 010202 Connected GUI Value Range: 0~64800
WRFD- Mode (CELL- Unit: s
010510 DCH, CELL-
PCH, URA- Actual Value Range: 0~64800
PCH, CELL- Default Value: 20
FACH)
3.4/6.8/13.6/27.
2Kbps RRC
Connection and
Radio Access
Bearer
Establishment
and Release
Establishment
and Release
TAC BSC69 ADD UIMEITAC WRFD- Terminal Black Meaning: Type Allocation Code (T
00 MOD UIMEITAC 160103 List consists of an eight digit string. If
RMV UIMEITAC WRFD- Enhanced Fast GUI Value Range: 0~99999999
020500 Dormancy Unit: None
Actual Value Range: 0~99999999
Default Value: None
TAC BSC69 ADD UIMEITAC WRFD- Terminal Black Meaning: Type Allocation Code (T
10 MOD UIMEITAC 160103 List consists of an eight digit string. If
RMV UIMEITAC WRFD- Enhanced Fast GUI Value Range: 0~99999999
020500 Dormancy Unit: None
Actual Value Range: 0~99999999
Default Value: None
HANGE_MSG_OPT_SWITCH:0,F
CELLUPDATE_PROCEDURE_O
14)D2P_DT_MSG_BUFFER_SW
Whether the RNC buffers the DIR
1: This switch is turned on. The R
0: This switch is turned off. The R
15)CM_CODE_CONFLICT_OPT_
Used to solve code resource conf
1: This switch is turned on. Code
0: This switch is turned off. Code
16)H_SERV_CELL_CHANGE_M
Whether to reduce the size of the
1: This switch is turned on. The si
0: This switch is turned off. The si
17)FAST_HSDPA_SERV_CELL_
Whether to enable the fast HSDP
1: This switch is turned on. The R
0: This switch is turned off. The R
18)RLRST_ASU_SUCC_COUNT
When the RL reestablishment fun
to correct the counting of success
1: This switch is turned on. Such
0: This switch is turned off. Such
19)COUNT_STATE_CHG_BY_R
Whether to enable certain state tr
1: This switch is turned on. These
0: This switch is turned off. These
20)RAB_RELATED_COUNTER_
Whether to optimize the statistics
1: This switch is turned on. Under
0: This switch is turned off. Under
21)CELLUPDATE_PROCEDURE
Whether to enable the optimized
1: This switch is set to on.
The RNC supports the overlappin
For UEs in the CELL_DCH state,
For UEs in the CELL_PCH or UR
message to the UE in the cell whe
UE through the DRNC while waiti
0: This switch is set to off. The op
22)PTT_PAGING_PRD_CRRCT_
Whether to correct the retransmis
Parameter ID NE MML Command Feature Feature Name
ID
RLRST_ASU_SUCC_COUNTER
COUNT_STATE_CHG_BY_RAB_
RAB_RELATED_COUNTER_OP
CELLUPDATE_PROCEDURE_O
PTT_PAGING_PRD_CRRCT_SW
RRC_REL_STATUS_RSP_RAB_
L2U_UP_DELAY_OPT_SWITCH
PRI_LDR_SYSHO_OUT_USE_S
Default Value:
SYS_RELOC_OUT_SUCC_STAT
FOREVER_PCH_CTRL_PLANE_
NFO_NOTIFY_NODEB_SWITCH
HANGE_MSG_OPT_SWITCH:0,F
CELLUPDATE_PROCEDURE_O
2D_OVERLAP_CELLUPT_SWIT
WITCH:1,RNC_RB_SCRI_NOT_
TCH:1,RB_SETUP_CIPHER_TIM
SWITCH:0,SCRI_COMPATIBLE_
32. PERFENH_UE_LTE_MEAS_
When this switch is turned on, the
capability carried in the IE "UE-Ra
GUI Value Range: PERFENH_HS
PERFENH_OLPC_BLER_COEF_
PERFENH_PTT_IUR_D2F_SWIT
PERFENH_P2D_LIMIT_ON_DCH
PERFENH_F2P_LIMIT_WITH_C
PERFENH_UL_CHL_CHG_OLPC
PERFENH_ICR_GSMNCELL_FIL
PERFENH_UE_LTE_MEAS_CAP
Unit: None
Actual Value Range:
PERFENH_HSUPA_LOC_BASED
PERFENH_HRETRY_OPT_SWIT
PERFENH_IUR_CSPS_RELOC_
PERFENH_HSUPA_PO_THROU
PERFENH_OLPC_BLER_COEF_
PERFENH_LITTLE_RATE_TIME
PERFENH_CS_TRIG_PS_P2D_Z
PERFENH_FACH_CONG_D2IDL
PERFENH_P2D_FAIL_RETRY_S
PERFENH_PTT_IUR_D2F_SWIT
PERFENH_LOW_VELO_OPT_S
PERFENH_SRB_FAST_HRETRY
PERFENH_PTT_H2F_OPT_SWI
PERFENH_IUR_DB_TICK_OPT_
PERFENH_P2D_LIMIT_ON_DCH
PERFENH_BASE_RES_BE_TTI_
PERFENH_BASE_ADM_CE_TTI
PERFENH_OLPC_SIRTAR_RES
PERFENH_F2P_LIMIT_WITH_C
PERFENH_CS_PS_F2H_RATE_
PERFENH_TTI_MC_UPDATE_O
PERFENH_HRETRY_OPT_WITH
PERFENH_UL_CHL_CHG_OLPC
PERFENH_IUR_CSPS_COMB_O
PERFENH_GSMOPGRP_TRANS
PERFENH_INTERRATHO_RETR
PERFENH_ICR_GSMNCELL_FIL
PERFENH_AMRC_DELAY_SWIT
Parameter ID NE MML Command Feature Feature Name
ID
PERFENH_AMRC_DELAY_UE_C
PERFENH_SMLC_D2F_ALLOW
PERFENH_CSPS_NO_RATEUP
Default Value:
PERFENH_HSUPA_LOC_BASED
DJUSTOPT:0,PERFENH_LITTLE
PERFENH_LOW_VELO_OPT_S
H:1,PERFENH_BASE_RES_BE_
F2H_RATE_LIMIT_SWITCH:0,PE
_GSMOPGRP_TRANSTOSRNC_
NH_SMLC_D2F_ALLOW_SWITC
AMRC_ON_122_AMR_HHO_RO
ASYN_RL_REEST_OPT_SWITC
SRVCC_RELOC_IN_USE_CS_K
CS_PAGING_OVERLAP_RRC_O
Unit: None
Actual Value Range:
RB_RLREEST_AM_TRB_RLC_R
RB_SETUP_UM_TRB_RLREEST
DRNC_RL_REEST_OPT_SWITC
URA2FACH_OVERLAP_CELLUP
RB_SETUP_F2D_USE_AM_RLC
RB_RECFG_D2F_USE_AM_RLC
RB_RECFG_F2D_USE_AM_RLC
RRC_UE_USER_SMOOTH_OPT
TRNC_LOAD_CTRL_SWITCH,
IU_SIG_REL_PCH_PAGING_SW
CPC_OPT_FOR_RLSETUP_SW
D2P_L2DEACT_FAIL_OPT_SWI
EFACH_RRC_REG_CMP_SWIT
P2D_TSID_ERR_UE_RSP_MSG
AMRC_ON_122_AMR_HHO_RO
RELOC_IN_RG_COMB_INDEX_
SCM_CU_CROSS_SWITCH,
DRNC_HSPA_CM_OPT_SWITC
IUB_TRANSID_OPT_SWITCH,
L2_ENHENCE_RECFG_OPT_SW
ASYN_RL_REEST_OPT_SWITC
RNC_IMSI_HO_OPT_SWITCH,
IUR_PRIQUEUE_INFO_TO_MOD
URA_PCH_LAC_RAC_CHG_NO
PAGING_OVERLAP_CU_OPT_S
SRVCC_RELOC_IN_USE_CS_K
SOCKET_RECEIVE_DATA_COR
CU_PRI_OVERLAP_OTHER_PR
INTERRAT2U_INTEG_PROTECT
CS_PAGING_OVERLAP_RRC_O
INTRA_NODEB_RLCC_INIT_CA
DRNC_RL_PARA_UPT_OPT_SW
Default Value:
RB_RLREEST_AM_TRB_RLC_R
WITCH:0,RB_RECFG_D2F_USE
Parameter ID NE MML Command Feature Feature Name
ID
SETUP_SWITCH:1,D2P_L2DEAC
LOC_SWITCH:0,SCM_CU_CRO
EUE_INFO_TO_MODIFY_OPT_S
CU_PRI_OVERLAP_OTHER_PR
:1
8)RRC_UE_USER_SMOOTH_OP
Whether the RNC corrects the va
1: This switch is turned on. The R
processing a signaling procedure
0: This switch is turned off. The R
counters again after their signalin
9)TRNC_LOAD_CTRL_SWITCH
Whether to enable load sharing fo
1: This switch is turned on. During
0: This switch is turned off. During
10)IU_SIG_REL_PCH_PAGING_
Whether the RNC sends paging m
1: This switch is turned on. The R
0: This switch is turned off. The R
11)CPC_OPT_FOR_RLSETUP_S
Whether the CPC is configured in
1: This switch is set to on. The CP
RNC changes the Enabling Delay
0: This switch is set to off. The CP
12) D2P_L2DEACT_FAIL_OPT_S
Whether to release the RRC conn
0: This switch is turned off. The R
1: This switch is turned on. The R
13)EFACH_RRC_REG_CMP_SW
Whether special UEs use the E-F
1: This switch is set to on. The RN
SETUP CMP message, the UE st
0: This switch is set to off. No spe
14) P2D_TSID_ERR_UE_RSP_M
Whether the RNC discards a RAD
1: This switch is set to on. The RN
0: This switch is set to off. The RN
15) AMRC_ON_122_AMR_HHO_
Whether the RNC performs rollba
0: This switch is set to off. The RN
1: This switch is set to on. The RN
16)RELOC_IN_RG_COMB_INDE
Whether the RNC allocates RG c
1: This switch is turned on. The R
0: This switch is turned off. The R
Parameter ID NE MML Command Feature Feature Name
ID
17)SCM_CU_CROSS_SWITCH(S
Whether the RNC supports the co
1: This switch is set to on. The RN
0: This switch is set to off. The RN
18)DRNC_HSPA_CM_OPT_SWI
Whether to solve the problem tha
Sequence Information and HS-DS
1: This switch is set to on. the rad
0: This switch is set to off, the rad
19)IUB_TRANSID_OPT_SWITCH
Whether the RNC allocates Trans
1: This switch is set to on. the RN
0: This switch is set to off. the RN
20)L2_ENHENCE_RECFG_OPT
Whether the RNC correctly recon
second service experiences a cel
When this switch is set to on, the
When this switch is set to off, the
21)ASYN_RL_REEST_OPT_SW
Radio link (RL) reestablishment o
When this switch is set to on, the
reconfiguration tag, the RL is rees
When this switch is set to off, the
22)RNC_IMSI_HO_OPT_SWITC
Whether the IMSI-based handove
1: This switch is set to on. In MOC
0: This switch is set to off. In MOC
23)IUR_PRIQUEUE_INFO_TO_M
Whether the RADIO LINK RECON
reconfiguration.
1: This switch is set to on. the RA
after the reconfiguration. In this ca
0: This switch is set to off. the RA
reconfiguration. In this case, a UE
24)URA_PCH_LAC_RAC_CHG_
Whether paging is performed whe
1: This switch is set to on. Paging
0: This switch is set to off. Paging
25)PAGING_OVERLAP_CU_OPT
Whether the RNC optimizes CS p
1: This switch is set to on. The RN
Parameter ID NE MML Command Feature Feature Name
ID
RB_SETUP_UM_TRB_RLREEST
DRNC_RL_REEST_OPT_SWITC
URA2FACH_OVERLAP_CELLUP
RB_SETUP_F2D_USE_AM_RLC
RB_RECFG_D2F_USE_AM_RLC
RB_RECFG_F2D_USE_AM_RLC
RRC_UE_USER_SMOOTH_OPT
TRNC_LOAD_CTRL_SWITCH,
IU_SIG_REL_PCH_PAGING_SW
CPC_OPT_FOR_RLSETUP_SW
D2P_L2DEACT_FAIL_OPT_SWI
EFACH_RRC_REG_CMP_SWIT
P2D_TSID_ERR_UE_RSP_MSG
AMRC_ON_122_AMR_HHO_RO
RELOC_IN_RG_COMB_INDEX_
SCM_CU_CROSS_SWITCH,
DRNC_HSPA_CM_OPT_SWITC
IUB_TRANSID_OPT_SWITCH,
L2_ENHENCE_RECFG_OPT_SW
ASYN_RL_REEST_OPT_SWITC
RNC_IMSI_HO_OPT_SWITCH,
IUR_PRIQUEUE_INFO_TO_MOD
URA_PCH_LAC_RAC_CHG_NO
PAGING_OVERLAP_CU_OPT_S
SRVCC_RELOC_IN_USE_CS_K
SOCKET_RECEIVE_DATA_COR
CU_PRI_OVERLAP_OTHER_PR
INTERRAT2U_INTEG_PROTECT
CS_PAGING_OVERLAP_RRC_O
INTRA_NODEB_RLCC_INIT_CA
DRNC_RL_PARA_UPT_OPT_SW
Default Value:
RB_RLREEST_AM_TRB_RLC_R
WITCH:0,RB_RECFG_D2F_USE
SETUP_SWITCH:1,D2P_L2DEAC
LOC_SWITCH:0,SCM_CU_CRO
EUE_INFO_TO_MODIFY_OPT_S
CU_PRI_OVERLAP_OTHER_PR
:1
Parameter ID NE MML Command Feature Feature Name
ID
EcN0ThdForBaseCover BSC69 SET UFRC WRFD- 3.4/6.8/13.6/27. Meaning: Ec/No threshold for an u
E2D 00 010510 2Kbps RRC and the Ec/No of the target cell in
Connection and GUI Value Range: 0~49
Radio Access Unit: 0.5dB
Bearer
Establishment Actual Value Range: -24.5~0(Actu
and Release Default Value: 25
EcN0ThdForBaseCover BSC69 SET UFRC WRFD- 3.4/6.8/13.6/27. Meaning: Ec/No threshold for an u
E2D 10 010510 2Kbps RRC and the Ec/No of the target cell in
Connection and GUI Value Range: 0~49
Radio Access Unit: 0.5dB
Bearer
Establishment Actual Value Range: -24.5~0(Actu
and Release Default Value: 25
20 HSUPA SIGNALING_SHO_UL_AC_SWIT
Users per Cell FAST_DORMANCY_ADCTRL(Fa
Unit: None
Actual Value Range: CRD_ADCT
HSUPA_EDCH_RSEPS_MEAS,
FACH_USER_NUM_NOT_CTRL
Default Value:
CRD_ADCTRL:1,HSDPA_UU_AD
U_ADCTRL:1,RTWP_RESIST_D
16) RNC_RB_SCRI_NOT_DROP
Whether the RB release due to S
1: This switch is turned on. The R
0: This switch is turned off. The R
17) RRC_RECONN_SWITCH
Switch for the RNC to process the
1: This switch is turned on. The R
0: This switch is turned off. When
different cells, the RNC releases t
It is recommended that this param
18) RRC_REPEAT_PFM_SWITC
Whether the RNC counts the num
1: This switch is turned on. The R
0: This switch is turned off. The R
19) F2D_NO_RSP_RRCREL_SW
Whether the RNC releases the RR
1: This switch is turned on. The R
VS.RAB.Rel.PS.F2DNoRsp coun
0: This switch is turned off. The R
20) CS_SETUP_P2D_SWITCH
Whether a UE in the CELL_PCH
1: This switch is turned on. The R
0: This switch is turned off. The U
21) SYSHO_CIPHER_IE_SWITC
Whether the relocation command
UMTS network.
1: This switch is turned on. The re
0: This switch is turned off. The re
22) P2P_GTPU_NOT_CFG_SWI
Whether to reconfigure the GPRS
1: This switch is turned on. The G
0: This switch is turned off. The G
23) RB_SETUP_CIPHER_TIME_
Whether the RNC adjusts the acti
1: This switch is turned on. The R
message is smaller than 200 conn
0: This switch is turned off. The R
24) CS_PRI_MOD_NOT_INT_SW
Whether the RNC re-initiates CS
1: This switch is turned on. The R
Parameter ID NE MML Command Feature Feature Name
ID
PAGGING_NUM_CTRL_SWITCH
ASU_RL_RESET_SWITCH,
MC_RL_RESET_SWITCH,
FD_PCH_REENTERSA_FORCE
UE_CRC_COMPATIBLE_SWITC
RNC_P2D_DRD_SWITCH,
P2D_SWITCH,
AMR_F2D_OVERLAP_CELLUPT
SRB_RESET_RL_SETUP_SWIT
RLFAIL_RL_SETUP_SWITCH,
CS_RL_SETUP_SWITCH,
PS_RL_SETUP_SWITCH,
UE_SRB_RESET_SWITCH,
RL_RESTORE_SWITCH,
RNC_EFD_D2F_SWITCH,
RNC_RB_SCRI_NOT_DROP_SW
RRC_RECONN_SWITCH,
RRC_REPEAT_PFM_SWITCH,
F2D_NO_RSP_RRCREL_SWITC
CS_SETUP_P2D_SWITCH,
SYSHO_CIPHER_IE_SWITCH,
P2P_GTPU_NOT_CFG_SWITCH
RB_SETUP_CIPHER_TIME_ADJ
CS_PRI_MOD_NOT_INT_SWITC
RAB_SETUP_TMSI_REALLOC_
IU_FAULT_REL_PS_RES_SWIT
RB_RECFG_RL_REEST_SWITC
F2P_DT_MSG_BUFFER_SWITC
SCRI_COMPATIBLE_SWITCH,
GTPU_ERR_IND_DEF_SWITCH
IUR_SRV_CELL_CHG_MACHS_
UL_INTEG_ALGO_COMPAT_SW
Default Value:
PAGGING_NUM_CTRL_SWITCH
2D_OVERLAP_CELLUPT_SWIT
WITCH:1,RNC_RB_SCRI_NOT_
TCH:1,RB_SETUP_CIPHER_TIM
SWITCH:0,SCRI_COMPATIBLE_
DRNC_DCH_RCV_CELL_RESEL
MULTIRAB_ATTESTAB_DEF_SW
PCH_UE_SRB_RESET_DSCR_S
DRNC_CELL_CODE_CONFLICT
RAB_FAIL_CAUSE_SWITCH,
PSPS_SETUP_REL_DEF_SWIT
RRC_CON_REQ_TIMES_COMP
SECU_CU_CROSS_SWITCH,
HHO_CNT_CORRECT_SWITCH
IRATHO_CNT_CORRECT_SWIT
RB_CU_CROSS_COMPATIBLE_
RNTI_ENH_ALLOC_AlGO_SWIT
DRNC_LOAD_CTRL_SWITCH,
EFACH_CU_COMMON_HRNTI_
PSCS_CALLDROP_FIX_SWITCH
CSABNREL_DUETO_PSREL_FI
Default Value:
DRNC_DCH_RCV_CELL_RESEL
P_REL_DEF_SWITCH:0,RRC_C
ALLOC_AlGO_SWITCH:0,DRNC
P_REL_DEF_SWITCH:0,RRC_C
ALLOC_AlGO_SWITCH:0,DRNC
21)SPECUSER_ENABLE_RPRT
Whether the RNC sends measure
1: Indicates that this switch is set
0: Indicates that this switch is set
22)SPECUSER_PS_SETUP_DC
Whether the RNC forbids special
1: Indicates that this switch is set
0: Indicates that this switch is set
23)SPECUSER_FACH_CONSIS_
Whether the RNC forbids the stat
1: Indicates that this switch is set
0: Indicates that this switch is set
This switch is set to OFF by defau
24)SPECUSER_ADJACENT_FR
Whether special UEs are prohibite
1: This switch is turned on. Specia
0: This switch is turned off. Specia
25)SPECUSER_RL_PERFORMA
Whether the RNC optimizes link p
1: Indicates that this switch is set
0: Indicates that this switch is set
GUI Value Range: P2F_REDIR_D
SPECUSER_ERACH_DISABLED
EFACH_ERACH_UE_D2P_DISA
SPECUSER_CELLID_RTT_MEA
SPECUSER_FASTMULRLSETU
SPECUSER_ENABLE_RPRT_AG
SPECUSER_RL_PERFORMANC
Unit: None
Actual Value Range:
P2F_REDIR_DISABLED_SWITC
SPECUSER_SRB_OVER_HSDP
SPECUSER_CPC_DTX_DRX_D
SPECUSER_EFACH_DISABLED
SPECUSER_ERACH_DISABLED
SPECUSER_PCH_FACH2EFAC
SPECUSER_INHIBIT_D2P_SWIT
H_SERV_CELL_CHG_MSG_OP
EFACH_ERACH_UE_D2P_DISA
SPECUSER_DL_BLER_MEAS_D
SPECUSER_AGPS_MEAS_DISA
Parameter ID NE MML Command Feature Feature Name
ID
SPECUSER_UE_TX_PWR_MEA
SPECUSER_CELLID_RTT_MEA
FAST_H_SERV_CELL_CHANGE
SPECUSER_SFDC_HSDPA_DIS
SPECUSER_DF3C_HSDPA_DIS
SPECUSER_FASTMULRLSETU
SPECUSER_R6_EFACH_CMP_S
SPECUSER_IFFASTMULRL_CM
SPECUSER_AGPS_MEAS_ENA
SPECUSER_ENABLE_RPRT_AG
SPECUSER_PS_SETUP_DCH0K
SPECUSER_FACH_CONSIS_OP
SPECUSER_ADJACENT_FREQ
SPECUSER_RL_PERFORMANC
Default Value: P2F_REDIR_DISA
SPECUSER_ERACH_DISABLED
_SWITCH:0,SPECUSER_DL_BL
ST_H_SERV_CELL_CHANGE_D
CH_CMP_SWITCH:0,SPECUSER
SWITCH:0,SPECUSER_FACH_C
10. PERFENH_HSPA_CODE_AL
immediately after the cell is set up
11. PERFENH_R99UPA_FAIRNE
turned off, the algorithm reduces
rate of only the users whose uplin
12. PERFENH_HSPDSCH_SF_F
on and HSDPA has been activate
allocates the last vacant SF16 co
13. PERFENH_OLC_REJ_F2DD
allows the DCCC-triggered F2D s
14. PERFENH_BGNOISE_QUICK
on the common measurement rep
measurement report that is report
15. PERFENH_HRNTI_OPT_SW
avoids incorrect demodulation. W
16. PERFENH_FDPCH_FAULTY
allocation fails and releases the u
17. PERFENH_CCH_DLCODE_R
codes after cell setup. When this
cell setup. When this switch is tur
18. PERFENH_SMALL_RATE_P
connection setup. When this switc
makes admission decisions only o
SF reserved for a handover can b
19. PERFENH_HSDPA_DLPWR_
HSDPA users only when this swit
always considered during downlin
20. PERFENH_TD_ALIGN_RRC_
configurations for HSUPA time div
connection setup phase.
21. PERFENH_DEACELL_PFMR
deactivation, the cell measuremen
22. PERFENH_BGNOISE_UPT_
calculates background noise at a
23. PERFENH_INTERRATHO_C
switch is turned off. The RNC doe
24. PERFENH_CSFBUSER_CAC
switch is turned off. The cell LDR
25. PERFENH_CRNTI_OPT_SW
allocated C-RNTI, and selects an
available C-RNTI for the UE.
26. PERFENH_FACHUSER_NUM
number of FACH UEs in a cell is l
and E-FACH UEs in a cell cannot
Parameter ID NE MML Command Feature Feature Name
ID
27. PERFENH_RELOCINUSER_
the user selection algorithm for LD
user priority is used for LDR and p
28. PERFENH_SOFTERHO_CE_
consumed on the link that is delet
29. PERFENH_LCGCE_RSRC_O
preempted, these resources are p
resources for preemption.
30. PERFENH_QUEUE_CANCEL
the resource consumed by the us
result, the consumed cell resourc
31. PERFENH_SRB_OVER_HSD
original DOFF allocation algorithm
optimized DOFF allocation algorit
Disuse Statement:Value of bit fiel
bit field, the system does not use
GUI Value Range: PERFENH_R9
PERFENH_CE_RLS_ADM_OPT_
PERFENH_HSPA_CODE_ALLOC
PERFENH_BGNOISE_QUICK_U
PERFENH_HSDPA_DLPWR_AD
PERFENH_INTERRATHO_CAC_
PERFENH_RELOCINUSER_LDR
PERFENH_SRB_OVER_HSDPA
Unit: None
Actual Value Range: PERFENH_
PERFENH_CE_RLS_ADM_OPT_
PERFENH_HSPA_CODE_ALLOC
PERFENH_BGNOISE_QUICK_U
PERFENH_HSDPA_DLPWR_AD
PERFENH_INTERRATHO_CAC_
PERFENH_RELOCINUSER_LDR
PERFENH_SRB_OVER_HSDPA
Default Value:
PERFENH_R99_BRDCSTHSPA_
CH:0,PERFENH_DTCH_FACH_C
_SWITCH:0,PERFENH_R99UPA
PT_SWITCH:1,PERFENH_FDPC
_TD_ALIGN_RRC_EFFECT:0,PE
:0,PERFENH_CRNTI_OPT_SWIT
1,PERFENH_QUEUE_CANCEL_
19. PERFENH_HSDPA_DLPWR_
HSDPA users only when this swit
always considered during downlin
20. PERFENH_TD_ALIGN_RRC_
configurations for HSUPA time div
connection setup phase.
21. PERFENH_DEACELL_PFMR
deactivation, the cell measuremen
configuration interface in this vers
22. PERFENH_BGNOISE_UPT_
calculates background noise at a
23. PERFENH_INTERRATHO_C
switch is turned off. The RNC doe
24. PERFENH_CSFBUSER_CAC
switch is turned off. The cell LDR
25. PERFENH_CRNTI_OPT_SW
allocated C-RNTI, and selects an
available C-RNTI for the UE.
26. PERFENH_FACHUSER_NUM
number of FACH UEs in a cell is l
and E-FACH UEs in a cell cannot
27. PERFENH_RELOCINUSER_
the user selection algorithm for LD
user priority is used for LDR and p
28. PERFENH_SOFTERHO_CE_
consumed on the link that is delet
29. PERFENH_LCGCE_RSRC_O
preempted, these resources are p
resources for preemption.
30. PERFENH_QUEUE_CANCEL
the resource consumed by the us
result, the consumed cell resourc
31. PERFENH_SRB_OVER_HSD
original DOFF allocation algorithm
optimized DOFF allocation algorit
Disuse Statement:Value of bit fiel
bit field, the system does not use
GUI Value Range: PERFENH_R9
PERFENH_CE_RLS_ADM_OPT_
PERFENH_HSPA_CODE_ALLOC
PERFENH_BGNOISE_QUICK_U
PERFENH_HSDPA_DLPWR_AD
PERFENH_INTERRATHO_CAC_
Parameter ID NE MML Command Feature Feature Name
ID
PERFENH_RELOCINUSER_LDR
PERFENH_SRB_OVER_HSDPA
Unit: None
Actual Value Range: PERFENH_
PERFENH_CE_RLS_ADM_OPT_
PERFENH_HSPA_CODE_ALLOC
PERFENH_BGNOISE_QUICK_U
PERFENH_HSDPA_DLPWR_AD
PERFENH_INTERRATHO_CAC_
PERFENH_RELOCINUSER_LDR
PERFENH_SRB_OVER_HSDPA
Default Value:
PERFENH_R99_BRDCSTHSPA_
CH:0,PERFENH_DTCH_FACH_C
_SWITCH:0,PERFENH_R99UPA
PT_SWITCH:1,PERFENH_FDPC
_TD_ALIGN_RRC_EFFECT:0,PE
:0,PERFENH_CRNTI_OPT_SWIT
1,PERFENH_QUEUE_CANCEL_
PERFENH_BASE_RES_BE_TTI_
PERFENH_BASE_ADM_CE_TTI
PERFENH_OLPC_SIRTAR_RES
PERFENH_F2P_LIMIT_WITH_C
PERFENH_CS_PS_F2H_RATE_
PERFENH_TTI_MC_UPDATE_O
PERFENH_HRETRY_OPT_WITH
PERFENH_UL_CHL_CHG_OLPC
PERFENH_IUR_CSPS_COMB_O
PERFENH_GSMOPGRP_TRANS
PERFENH_INTERRATHO_RETR
PERFENH_ICR_GSMNCELL_FIL
PERFENH_AMRC_DELAY_SWIT
PERFENH_AMRC_DELAY_UE_C
PERFENH_SMLC_D2F_ALLOW
PERFENH_CSPS_NO_RATEUP
Default Value:
PERFENH_HSUPA_LOC_BASED
DJUSTOPT:0,PERFENH_LITTLE
PERFENH_LOW_VELO_OPT_S
H:1,PERFENH_BASE_RES_BE_
F2H_RATE_LIMIT_SWITCH:0,PE
_GSMOPGRP_TRANSTOSRNC_
NH_SMLC_D2F_ALLOW_SWITC
10 Counters
UMTS:
WRFD-
010610
LTE:
None
50341659 VS.DataTtiRatio.Mean Ratio of the time when NodeB Multi- HSDPA Introd
at least one HSDPA mode: Package
user has data to None HSDPA Inter-
transmit in the queue GSM: Power Sharin
buffer None
UMTS:
WRFD-
010610
WRFD-
160251
LTE:
None
Establishmen
Release
UE State in
Connected Mo
(CELL-DCH, C
PCH, URA-PC
CELL-FACH)
Intra RNC UR
Update
Inter RNC UR
Update
CELL_FACH to
CELL_PCH for Cell
WRFD- 32 HSDPA Us
010622 Cell
WRFD- 64 HSDPA Us
010623 Cell
PCH, URA-PC
CELL-FACH)
PCH, URA-PC
CELL-FACH)
CELL_PCH or
URA_PCH for Cell
11 Glossary
12 Reference Documents
9. 3GPP TS 25.331