Beruflich Dokumente
Kultur Dokumente
Series/Type: P 18 x 11
The following products presented in this data sheet are being withdrawn.
Ordering Code Substitute Product Date of Withdrawal Deadline Last Last Shipments
Orders
B65659F0001X001 B65659F1X23 11.11.2005 30.04.2006 30.06.2006
For further information please contact your nearest EPCOS sales office, which will also support you in selecting a
suitable substitute. The addresses of our worldwide sales network are presented at www.epcos.com/sales.
P 18 × 11
Core B65651
14.9+0.5
18.4 _ 0.8
3.9+0.5
with without
center hole center hole
Σl/A 0.6 0.57 mm–1
le 25.9 26.6 mm
ø7.6 _ 0.3
0.35+0.1
Ae 43 46.7 mm2
Amin — 33.9 mm2 ø3+0.1
2.4±0.15
Ve 1114 1242 mm3
10.6 _ 0.2
s
7.2+0.4
Approx. weight (per set)
m 6.0 6.6 g
M2 FPK0238-B
Gapped
Ungapped
1) Replace the + by the code letter ”D“ or ”T“ for the required version.
Coil former
Standard: to IEC 60133
Material: GFR polyterephthalate (UL 94 V-0, insulation class to IEC 60085:
F max. operating temperature 155 °C), color code black
Valox 420-SE0 ® [E45329 (M)], GE PLASTICS B V
Winding: see Data Book 2007, chapter “Processing notes, 2.1”
Coil former
AN
ø8.7_ 0.1
14.8 _ 0.2
ø7.7+0.1
2+0.6
0.5
7_ 0.1
FPK0351-9
Insulating washer
(preliminary data)
Terminal carrier
Material: GFR polyterephthalate (UL 94 V-0, insulation class to IEC 60085:
F max. operating temperature 155 °C), color code gray
Pocan B4235 ® [E245249 (M)], LANXESS AG
Solderability: to IEC 60068-2-20, test Ta, method 1 (aging 3): 235 °C, 2 s
Resistance to soldering heat: to IEC 60068-2-20, test Tb, method 1B: 350 °C, 3.5 s
Yoke
Spring yoke, made of tinned nickel silver (0.3 mm), with ground terminal
Ground Ground
20.1 max.
20.1 max.
4
4
1
1
8
5
8
5
*) *)
20.1 max. 20.1 max.
a a
13.5 max.
13.5 max.
Ground Ground
3.5
3.5
ø1.3+0.1
ø1.3+0.1
2.54 2.54
20.7 max. FPK0295-U 20.7 max. FPK0296-3
*) This recess must be on the side of the grounding pin to ensure that the yoke locks in position.
a) Yoke
b) Terminal carrier with 4 solder terminals
c) Terminal carrier with 8 solder terminals
Adjusting screw
■ Tube core with thread and core brake made of GFR polyterephthalate
Pocan B3235 ® [E245249 (M)], LANXESS AG
a b c
Heating up
Ferrites can run hot during operation at higher flux densities and higher frequencies.
NiZn-materials
The magnetic properties of NiZn-materials can change irreversible in high magnetic fields.
Processing notes
– The start of the winding process should be soft. Else the flanges may be destroid.
– To strong winding forces may blast the flanges or squeeze the tube that the cores can no more
be mount.
– To long soldering time at high temperature (>300 °C) may effect coplanarity or pin arrangement.
– Not following the processing notes for soldering of the J-leg terminals may cause solderability
problems at the transformer because of pollution with Sn oxyd of the tin bath or burned insulation
of the wire. For detailed information see Data Book 2007, chapter “Processing notes, 2.2”.
– The dimensions of the hole arrangement have fixed values and should be understood as a
recommendation for drilling the printed circuit board. For dimensioning the pins, the group of
holes can only be seen under certain conditions, as they fit into the given hole arrangement. To
avoid problems when mounting the transformer, the manufacturing tolerances for positioning the
customers’ drilling process must be considered by increasing the hole diameter.
6 09/06
Important notes
7 09/06