Beruflich Dokumente
Kultur Dokumente
DBIL18U21P20G70, DBIG18U21P20G70
User Manual
The copyright of this document is owned by Fujian Helios Technologies Co., Ltd. without the prior
written permission obtained from Fujian Helios Technologies Co., Ltd., this document shall not be
reproduced and excerpted in any form or by any means, stored in a retrieval system, modified,
distributed and translated into other languages, applied for a commercial purpose in whole or in
part.
Disclaimer
This document and the information contained herein is provided on an “AS IS” basis. Helios® may
make improvement or changes in this document, at any time and without notice and as it sees fit.
Local Representative:
Fujian Helios Technologies Co., Ltd.
Thanks for choosing Helios Multi Bands Digital Pico Repeaters, please read the
User Manual carefully before using the device.
1 Overview
Helios® Multi Bands Digital Pico Repeater is a carrier-grade, consumer-friendly digital smart
signal booster that maximizes a subscriber’s indoor wireless experience by eliminating
in-building dead zones. It is real cost-effective and intelligent solution to solve the last mile
coverage problem, which is adopting SDR (Software Define Radio) technology basis on FPGA&
DSP (Digital Signal Processing) platform. It enables on-the-fly filter be changed/upgraded by
software without expensive hardware upgrading. It can support multi sub-band selective
(bandwidth tunable).
In fact, Helios® Multi Bands Digital Pico Repeater is able to intelligently and automatically sense
and adapt to its dynamic RF environment. By continuously monitoring the gain and making
real-time adjustments, the system will never overdrive the base station or raise the noise floor.
SOC & Embedded architecture enables to delivery significantly improving network coverage with
very low power consumption.
It is connected via coaxial cable to Donor Antenna and Service Antenna, Donor Antenna is
placed outside the building where it has easy access to a BTS signal, and the Service Antenna is
placed in the building where it can extend radio coverage to the blind area.
2 Illuminating
3 Product Overview
A
H D
C
F G E J
I
A. Main LOGO
4
www.heliostelecom.com
Fujian Helios Technologies Co., Ltd.
PWR: Green Lighting during internal power supply is normal after self-checking
(including +12V, +5V and +3.3V etc.)
WRK: It blinks every 4 seconds(2 seconds active and 2 seconds inactive) after 1 and
half minutes in case of power on.
ALM: Red Lighting on any Alarm when the corresponding alarm is enabled.
E. MODEM LED: Shows the working status of mobile modem. It’s active after 1 minute in
case of power on. It blinks every 1 second during modem initializing; SMS mode: It
blinks every 3 seconds; GPRS mode: It flashes fast.
G. USB port: Connect to laptop via USB cable for local control
4 Features
Cost effective solution making coverage more affordable for small buildings or driving a DAS (Distributed
Antenna System) in larger buildings.
Small neat and compact package, simple and quick to install.
Support upgrading in case of frequency re-farming by software.
Flexible Bandwidth Adjustable/Upgrade by Software, and each sub-band/channel can be switched on/off
by software.
Compatible with baseband hoping and synthesized hopping.
Better out of band rejection than analog SAW IF filter.
Lower Power consumption and Lower cost of indoor coverage and rapidly increases capacity of GSM,
UMTS, LTE wireless networks.
Automatic Gain Control (AGC) continuously monitors path loss and transmit power to deliver max gain.
Built-in USB port interface for local control.
Built-in wireless modem (Option) for remote monitoring by SMS, GPRS or TCP/IP.
5
www.heliostelecom.com
Fujian Helios Technologies Co., Ltd.
5 Application Diagram
6 Technical Specification
Related to the datasheet.
7 Typical Applications
Office, mini basement and so on.
Pub, net bar, dance hall, coffee hall, health club, entertainment place, house, office plant,
yacht, public security system and so on.
8 Installation
Donor Antenna Installation:
A. Recommended Donor Antenna is Yagi antenna or Log antenna (gain is higher than 10dBi).
6
www.heliostelecom.com
Fujian Helios Technologies Co., Ltd.
B. Donor Antenna Location: Find the place (building exterior wall or roof parapet) where target
BTS’ RSCP (for WCDMA system) is higher than -80dBm (optimum RSCP is from -80dBm to
-50dBm) and Ec/No is higher than -9dB (cannot be less than -13dB) on the top or around the
building by using Drive Test Tools. Sometimes the location can be podium on the lower floors,
or stairwell with glass window. For GSM system, the Rx Level shall be higher than -70dBm
(optimum Rx Level is from -70dBm to -40dBm) and Rx Quality is less than 2 (cannot be
higher than 5). Below instructions are based on WCDMA system.
C. Install Donor Antenna with bracket on the selected location. Please note that users shall try
to lower the height of Donor Antenna as low as possible (RSCP>-80dBm) to get better Ec/No.
It’s better that the height of Donor Antenna is not higher than 20meters (7 floors).
D. Connect Donor Antenna to a Spectrum Analyzer or SiteMaster. Observe RSSI of target BTS.
Adjust Donor Antenna direction and lock the direction which gets the maximum RSSI. If
there’s stronger competitors’ BTS nearby, then the Donor Antenna cannot face to the
competitors’ BTS directly. Users shall change the antenna to the opposite direction
and find new target BTS. Target BTS’ RSSI shall be higher than the competitors’.
E. Fix and fasten the Donor Antenna on the bracket when antenna direction is locked.
Repeater Installation:
F. Find a suitable place where is near the power supply with weatherproof condition and good
airiness.
G. Fasten the brackets for installation onto the back side of the Pico Repeater as below:
7
www.heliostelecom.com
Fujian Helios Technologies Co., Ltd.
I. Put the Pico Repeater on the wall and mark the points for screw plug.
K. Pound the screw plugs into the drilled holes with hammer.
L. Drive tapping screws into the screw plugs and remain 5mm length of the screws outside of
the wall.
M. Carry and hang the repeater onto the screws, fix and fasten it.
N. In order to ensure higher work gain and stable operation, users should improve isolation
between donor antenna and service antenna, such as increasing distance in vertical or in
horizontal and making full use of obstacles (such as buildings etc.)
O. Indoor DAS (Distributed Antenna System) includes omni-directional ceiling mount antennas
(3dBi), directional wall mount antennas (8dBi), splitters (2-way, 3-way and 4-way), directional
couplers (5-30dB) and feeder cable etc. Users shall survey and design the system as
uniform distribution to cover the whole building.
8
www.heliostelecom.com
Fujian Helios Technologies Co., Ltd.
P. Confirm and fasten the indoor service antenna at suitable place (It is better to install the
omni-directional ceiling antennas at the center of coverage area and directional wall mount
antennas towards the aimed coverage area.
Q. Connect all passive devices with 1/2” feeder cable and fix the feeder cable on the wall or on
the ceiling. Ensure all connections are correct and lock them.
R. Lay and fix 1/2” feeder cable (if the length is over 30meters, then 7/8” feeder cable is
suggested) from Donor Antenna to BTS port of the Pico Repeater.
S. Lay and fix 1/2” feeder cable (if the length is over 30meters, then 7/8” feeder cable is
suggested) from Service Antenna (or DAS) to MS port of the Pico Repeater.
T. In-building part of feeder cable is recommended to be sheathed in white PVC pipe and white
corrugated sleeve pipe.
U. All of the joints of the outside part in feeder antenna system shall have waterproofing
process with PVC tape and Butyl rubber tape.
9
www.heliostelecom.com
Fujian Helios Technologies Co., Ltd.
V. All of the joints of the inside part in feeder antenna system or DAS shall have dust-proofing
process with PVC tape.
X. If Donor Antenna and/or Service Antenna is outside, then the corresponding input port of the
repeater is recommended to be inserted Surge Arresters.
Y. Connect GND of both Pico Repeater and Surge Arrester to the nearest grounding bar with
green-yellow wire. Now, the primary installation is finished.
9 Commissioning
Isolation is the path loss between the BTS port and the MS port of the Repeater which will
influences Repeater system gain. If the isolation is not enough, it will be in self-oscillation
and cannot work normally.
According to practical engineering experience, the isolation must be 15dB greater than
system gain to prevent self-oscillation.
As below diagram, connect SG (Signal Generator) to the Donor Antenna, set Amplitude as
10dBm and Frequency as working frequency. Connect SA (Spectrum Analyzer) to
10
www.heliostelecom.com
Fujian Helios Technologies Co., Ltd.
the Service Antenna and test the output power Po, then Isolation will be:
Iso = 10 - Po
For example, if the repeater working gain is 65dB, then requested Isolation is at least 80dB.
Donor Antenna
Service Antenna
Signal Generator
Spectrum Analyzer
2) Test VSWR both Donor Antenna and Service Antenna with feeder cable via SiteMaster,
VSWR shall less than 1.5. Otherwise, users shall check the connection between antennas
and feeder cable.
11
www.heliostelecom.com
Fujian Helios Technologies Co., Ltd.
5) Plug in the power supply cable to the nearest 220VAC mains socket.
6) Power On.
7) Check the green PWR LED indicator of the Repeater should be light on.
8) According to the tested Isolation between Donor Antenna and Service Antenna, users shall
log into LCT software and configure suitable work gain in Advance page. Work gain of each
band shall be less than (Isolation - 15dB).
9) Configure working frequency band in Channel page for each band. The unused sub-bands
shall be switched off.
10) Downlink output power: The rated downlink output power is 20dBm (composite power). In
normal circumstances, the downlink output power of the UMTS repeater is for pilot power. In
order to ensure stable audio or video call, users shall remain 3~6dB space for traffic.
That is to say, users shall modify Downlink ATT so that Downlink output power
showed in NMS is less than 16dBm. At the same time, users shall modify Uplink ATT
the same value as Downlink to balance the uplink and downlink. Otherwise,
sometimes it’s difficult to establish video call or other data service within repeater
coverage range.
11) The Digital RF Repeater can run normally after above process. Users can have a Walk Test
or CQT Test to check the working status and compare the coverage performance between
before and after.
12) Check remote control via Netview (Helios NMS based on Browser/Server configuration).
13) More details, please refer to below chapters about Local Control and Remote Control.
Connect USB Port of Digital Pico Repeater with laptop via USB cable.
Hardware:
Software
13
www.heliostelecom.com
Fujian Helios Technologies Co., Ltd.
Click Close to finish the installation of LCT software for local control.
10.4 Log on
Double click SignalTouch shortcut on the desktop to open the LCT software.
14
www.heliostelecom.com
Fujian Helios Technologies Co., Ltd.
Administrator: has the right to set and query all information& parameters.
After successful log in, it will enter into the main windows of SignalTouch, and shows the
default page of “Basic Information”. If log in by Administrator, the main window includes five
pages, such as “Basic Information”, “Channel”, “Advance”, “Hardware” and “OMC”. Please
refer to “Figure 2”. Click close button on the top right corner of the main window to log out.
15
www.heliostelecom.com
Fujian Helios Technologies Co., Ltd.
This page shows the basic information about working status such as input power, output
power, isolation, temperature, Donor antenna status, alarm status and USB communication
status etc. as Figure 2.
Device Status: Working status of the Pico repeater, normal or alarm.
UL Input Power: Uplink input power in dBm.
UL Output Power: Uplink output power in dBm.
DL Input Power: Downlink input power in dBm.
DL Output Power: Downlink output power in dBm.
Isolation: Isolation between Donor Antenna and Service Antenna, for ICS repeater
only.
Temperature: Working temperature of Pico Repeater. In case the temperature is over
80 degrees Celcius, it will shut down Pico Repeater and it will return to normal working
when the temperature is lower than 60 degrees Celcius. In case the temperature is
lower than -20 degrees Celcius, PA won’t work until the temperature is over -15
degrees Celcius.
BTS Antenna: Shows External Donor ANT (ExDA) or Embedded Donor ANT (EmDA).
In case power on or reset, it will judge it’s connected to ExDA or EmDA, even this
repeater is ExDA type only.
If input power is less than -90dBm, then it will be in EmDA mode. It shows
“Embedded Donor ANT”. Users shall connect an ExDA to Pico Repeater and power
off on it again.
If input power is more than -90dBm, it will be in ExDA mode. It shows “External
Donor ANT”.
PA On/Off: PA Working status of Pico Repeater.
Alarm: Shows alarm information.
Communication: Shows communication status via USB cable. In case it shows “USB
Communication Failure”, users shall check the connection with the computer.
10.6 Hardware
This Page shows hardware information of Pico Repeater. Most of the information is
reserved for the manufacturer. Users don’t need to concern. But before monitor and control,
users need to select which RF card to be checked by 485 address configuration.
16
www.heliostelecom.com
Fujian Helios Technologies Co., Ltd.
Figure 3 Hardware
For example, users need to check the status of DCS1800 RF Card, just modify 485
address to DCS, 0 and click Set.
10.7 Channel
This Page shows all detailed parameters for each channel/sub-band.
DBIL18U21P20G70 and DBIG18U21P20G70 adopts band selective and channel selective
design: DCS supports 4 tunable sub-band (2 sub-band 0.2-5MHz tunable, 2 sub-band
0.6-10MHz tunable); and WCDMA support 4 carriers.
For DCS channel setting, each sub-band is configured by setting start frequency and stop
frequency. In Channel page, CH1 is start frequency and CH2 is stop frequency of Sub-band
I…CH7 is start frequency and CH8 is stop frequency of Sub-band IV… For WCDMA
channel setting, just fill the center frequency.
Please make sure right frequency settings for both uplink and downlink. All of the channels/
sub-bands shall be configured as frequencies with 0.1MHz recommended resolution but
not ARFCN or UARFCN.
17
www.heliostelecom.com
Fujian Helios Technologies Co., Ltd.
Figure 4 Channel
CH#: Channel or Sub-band Number. Odd channel is for start frequency, and even
channel is for stop frequency
UL Freq. MHz: The center frequency point of each channel or start/stop frequency
point of sub-band (uplink) which can be revised by users. Minimum resolution:
0.01MHz, recommended resolution: 0.1MHz (Note: it will be valid only within the
device’s preset working frequency range).
DL Freq. MHz: The center frequency point of each channel or start/stop frequency
point of sub-band (downlink) which can be revised by users. Minimum resolution:
0.01MHz, recommended resolution: 0.1MHz (Note: it will be valid only within the
device’s preset working frequency range).
Channel SW: Switch On/Off CH# or Sub-band (both uplink and downlink).
UL I/P PWR dBm: Uplink input power of CH# or Sub-band in dBm.
UL O/P PWR dBm: Uplink output power of CH# or Sub-band in dBm.
DL I/P PWR dBm: Downlink input power of CH# or Sub-band in dBm.
DL O/P PWR dBm: Downlink output power of CH# or Sub-band in dBm.
UL Freq. Read: Read Uplink frequency of all of CHs or Sub-bands in MHz.
DL Freq. Read: Read Downlink frequency of all of CHs or Sub-bands in MHz.
Channel SW Read: Read Channel18 Switch Status of all of CHs or
www.heliostelecom.com
Fujian Helios Technologies Co., Ltd.
10.8 Advance
This Page shows advanced parameters of Pico Repeater.
Figure 5 Advance
UL AGC Threshold: Uplink AGC Threshold in dBm. It will control uplink output power
not to exceed the threshold automatically.
19
www.heliostelecom.com
Fujian Helios Technologies Co., Ltd.
10.9 OMC
This Page shows configuration of remote control. DBI1821P18G70/DBIG18U21P20G70
supports built-in GPRS modem. After right configuration, it will contact with OMC (Helios
Netview) and create a new site in Netview automatically.
Figure 6 OMC
21
www.heliostelecom.com