Beruflich Dokumente
Kultur Dokumente
1-The degree of closeness of the measured value of a certain quantity with its true value is known as
Accuracy
Precision
Standard
Sensitivity
(Ans: a)
2-Error of measurement =
True value – Measured value
Precision – True value
Measured value – Precision
None of the above
(Ans: a)
3-The ability by which a measuring device can detect small differences in the quantity being measured by it, is called its
Damping
Sensitivity
Accuracy
None of the above
(Ans: b)
13-Following is the theoretical size which is common to both the parts of a mating pair
Normal size
Actual size
Base size
All of the above
(Ans: c)
14-_____ is equal to the differences of the two limits of size of the part
Tolerance
Low limit
High limit
Design size
(Ans: a)
15-The amount by which the actual size of a shaft is less than the actual size of mating hole in an assembly
Clearance
Interference
Allowance
None of the above
(Ans: a)
16-The amount by which the actual size of a shaft is less than the actual size of mating hole in an assembly
Clearance
Interference
Allowance
None of the above
(Ans: b)
17-A positive allowance will always result in a _____ fit.
Clearance
Interference
both ‘a’ and ‘b’
Any of the above
(Ans: a)
30-The following method(s) is (are) used to measure the minor diameter of internal threads
Taper parallels methods
Calibrated rollers methods
both ‘a’ and ‘b’
None of the above
(Ans: c)
3. When size of smallest hole is more than size of biggest shaft then it is
a) Clearance fit
b) Interference fit
c) Transition fit
d) None of the mentioned
Answer: a
Explanation: When size of smallest hole is more than size of biggest shaft then it is clearance fit.
6. When size of smallest shaft is more than size of biggest hole then it is
a) Clearance fit
b) Interference fit
c) Transition fit
d) None of the mentioned
Answer: b
Explanation: When size of smallest shaft is more than size of biggest hole then it is interference fit.
3-Which hormone in our body helps us to adjust to stress when we are angry, embarrassed or worried?
Thyroxine
Adrenaline
Insulin
Estrogen
(Ans: b)
7-Human Nutrition includes nutrient requirement, mode of intake of food and its utilization in the body occurring in various
steps which are
A. Absorption, B. Egestion, C. Assimilation, D. Ingestion, E. Digestion
Arrange these steps in sequence as they occur inside the body
A, B, C, D, E
D, E, A, C, B
E, D, C, A, B
D, A, B, C, E
(Ans:b)
8-Medium A is optically denser than Medium B. Which one of the following statements is true?
Speed of light is more in medium A than in medium B.
Speed of light is more in medium B than in medium A.
Speed of light is same in both A and B.
Cannot be compared.
(Ans: b)
9-A block of iron dropped in a vessel of water, sinks to the bottom. This is because
the vessel is not deep enough to allow the block to float
the weight of the water displaced by the block is less than the weight of the block
the weight of the block is less than the weight of the water displaced by the block
the density of water is more than the density of the block
(Ans: b)
10-There are two planets in our solar system which rotate from east to west. These planets are:
Mercury and Uranus
Venus and Uranus
Mercury and Venus
Uranus and Neptune
(Ans: b)
ANSWER: Profilometer
Q. Which type of errors show linear relation between cumulative pitch error and length of thread?
a. Periodic errors
b. Progressive errors
c. Both a. and b.
d. None of the above
Q. Which of the following statements is/are false for Co-ordinate measuring machine?
a. Conventional comparators have greater accuracy than co-ordinate measuring machines
b. Gantry type of co-ordinate measuring machine use inductive transducers for measurement
c. Loading and unloading operations are easily done by cantilever type of co-ordinate measuring machine
d. All the statements are false
ANSWER: Conventional comparators have greater accuracy than co-ordinate measuring machines
Q. According to laser Doppler principle, light experiences a change in its frequency when it comes in contact with a moving
object depending upon
a. the velocity of the object
b. the direction of the object
c. both a. and b.
d. none of the above
Q. According Juran's Triology, which of the following actions is performed under planning procedure?
a. choosing control subjects
b. organizing project teams
c. project establishment
d. deal with resistance to change
Q. Which award is presented to different organizations for quality and excellent performance by president of USA?
a. Malcolm Balbridge National Award
b. Dr. W. Edward Deming National Award
c. US Excellence Award
d. None of the above
Q. Relaxed ambiance for group participation is observed in which type of brain storming sessions?
a. structured sessions
b. unstructured sessions
c. both a. and b.
d. none of the above
ANSWER: as number of items in a sample increase, higher is the possibility of number of defectives thereby probability of
acceptance decreases
Q. Grade 1 is used in
a. high precision tasks
b. department of inspection
c. calibration of instruments
d. all of the above
ANSWER: autocollimator
Q. The sensitivity of back pressure air gauge is given by the relation shown below, what does δ R / δ p2 signify?
(δR / δt) = (δ Am / δ t) x (δ R / δ p2 ) x (δ p2 / δ Am )
a. Pneumatic sensitivity
b. Sensitivity of pressure gauge
c. Overall magnification
d. Measuring head sensitivity
Q. Which error is observed due to lack of squareness when depth is measured using depth micrometer?
a. parallax error
b. cosine error
c. sine error
d. all of the above
ANSWER: cosine error
ANSWER: 3.94 mm
ANSWER: Floating carriage type of micrometer is used for two wire method ----
Q. Calculate the tool width of a gear having 30 number of teeth and with module 5 mm.
a. 6.352 mm
b. 5.555 mm
c. 7.850 mm
d. none of the above
ANSWER: 7.850 mm
Q. A gear has 30 teeth with module 4 mm and pressure angle of 20o. Calculate length of base tangent in a gear over 7 teeth
space.
a. 21.25 mm
b. 90.23 mm
c. 62.53 mm
d. None of the above
ANSWER: 90.23 mm
Q. Which of the following is a contact type of automated inspection method?
a. Inspection probe
b. Laser scanning
c. Electric field
d. All of the above
Q. Which are the different techniques used by interpretation segments for interpretation?
a. frame grabber and frame store
b. template matching and weighting
c. thresholding and edge detection
d. all of the above
Q. Which of the following strategies of Deming's fourteen points is included into category of Management commitment?
a. Institute leadership
b. Encouraging education
c. Eliminating exhortations
d. Adopting new philosophy
Q. Which among the following depicts positive and negative relation between driving factor and performance factor?
a. Scatter diagram
b. histogram
c. check sheet
d. none of the above
ANSWER: Scatter diagram
ANSWER: C chart
ANSWER: β
Q. Which ISO standard is used in international automobile companies to set automotive quality system standards ?
a. ISO 14000
b. TS 16949
c. ISO 9000
d. none of the above
ANSWER: TS 16949
ANSWER: Diameter
Q. Calculate the range of linear scale for pressure ratios between 0.6 to 0.8. The air is supplied at 5 bar to the control jet,
which has a diameter of 0.45 mm and the diameter of measuring jet is 0.83 mm.
k1 = – 0.5 & k2 = 1.1
a. 0.244 mm
b. 0.0976 mm
c. 0.0244 mm
d. None of the above
ANSWER: 0.0244 mm
ANSWER: 45o
Q. Which type of surface in a fringe pattern exhibits the movement of fringes towards the centre?
a. concave surface
b. convex surface
ANSWER: concave surface
ANSWER: It is the average difference of five highest points and five deepest valleys measured within sampling length
ANSWER: Effective diameter of nut decreases and effective diameter of bolt increases
Q. According to Taylor's principle which type of gauge checks both size and geometric features?
a. Go gauge
b. No go gauge
c. Both a. and b.
d. None of the above
ANSWER: Go gauge
ANSWER: In single shear technique, two images have edge to edge contact and later on one image is shifted some distance
over the other
Q. Which sampling method is used when simple random sampling method becomes inconvenient to use in large lots?
a. systematic sampling
b. stratified sampling
c. cluster sampling
d. sampling in stages
ANSWER: Quality assurance deals with activities which prove that products and services meet the required quality standard
Q. Which of the following materials is/are used to make an angle gauge block?
a. Hardening tool steel
b. Nickel
c. Tungsten carbide
d. All of the above
ANSWER: All of the above
Q. Which of the following statements is true for LVDT?
a. It is a mutual capacitive transducer
b. Presence of hysteresis gives high repeatability
c. It can measure displacement and pressure
d. All of the above
Q. What is the phase difference, when the system is operated at excitation frequency ?
a. Phase difference is greater than 90o
b. Phase difference is less than 90o
c. Phase difference is zero
d. Unpredictable
ANSWER: Distance between maximum inscribing circle and minimum circumscribing circle measured radially
Q. Which of the following is tested for parallelism between trajectory and a plane?
a. plane is on a component which moves
b. plane is on a component which does not moves
c. both a. and b.
d. none of the above
Q. Which method gives accurate results when effective diameter is measured without considering the thread angle?
a. Two wire method
b. Three wire method
c. Best wire size
d. All the above
Q. Which of the following instruments is used to measure base pitch of a gear in base tangent method?
a. Gear tooth vernier caliper
b. David Brown tangent caliper
c. David Brown tangent comparator
d. David Brown tangent micrometer
Q. Which of the following statements is/are true according to Deming's Deadly Diseases?
a. short term profits are very useful for long term goals
b. mobility of management leads to stability
c. merit rating leads to devastating
d. all of the above
ANSWER: Maximum percentage of defective parts for sampling purpose are considered satisfactory as a process average
Q. Which quality management program is related to the maintenance of plants and equipments?
a. Environmental management systems
b. Fault tree analysis
c. Failure mode effect analysis
d. Total productive maintenance
ANSWER: 28.95o
Q. Which among the following has lowest thermal conductivity among the others?
a. silver
b. water
c. mercury
d. copper
ANSWER: water
Q. In which phase of a substance does conduction mode of heat transfer take place?
a. solid
b. liquid
c. gaseous
d. all of the above
Q. What is the condition for conduction mode of heat transfer between two bodies?
a. the two bodies must be in physical contact
b. there must be temperature gradient between the bodies
c. both a. and b.
d. none of the above
Q. In which mode, does the heat energy transfer between two bodies when they are separated by some distance and there is
no any medium between them?
a. conduction mode of heat transfer
b. convection mode of heat transfer
c. radiation mode of heat transfer
d. heat transfer cannot takes place with above condition
Q. In a process of heat transfer by convection from a body to the surrounding fluid, the convection heat transfer coefficient
a. remains constant over the entire surface of the body
b. does not remain constant over the entire surface of the body
c. none of the above
ANSWER: does not remain constant over the entire surface of the body
Q. Which two processes are unitedly responsible in the transfer of heat between solid surface and surrounding fluid?
a. conduction and convection
b. conduction and mass transfer
c. convection and mass transfer
d. none of the above
Q. When the surface of a body is at higher temperature than the surrounding fluid, then the heat flows firstly from surface of
the body to the adjacent layer of fluid by
a. convection
b. conduction
c. radiation
d. none of the above
ANSWER: conduction
Q. The fluid flow in which the fluid particles in one layer do not mix with the fluid particles in the other layer is called as
a. laminar flow
b. turbulent flow
c. layer flow
d. none of the above
ANSWER: laminar flow
ANSWER: the rate of convection heat transfer increases with increase in the rate of mixing in turbulent fluid flow
Q. The range of waves within which all possible frequencies of electromagnetic radiation are represented is called as
a. electromagnetic frequencies
b. electromagnetic spectrum
c. electromagnetic range
d. none of the above
Q. How is the wavelength of radiation (λ) calculated, when propagation velocity (C) and frequency (ν) of the radiation is given?
a. λ = C x ν
b. λ = C / ν
c. λ = ν / C
d. none of the above
ANSWER: λ = C / ν
Q. What is the approximate wavelength range of thermal radiation?
a. 0.1 to 100 μm (micrometer)
b. 0.1 to 100 nm (nanometer)
c. 0.1 to 100 cm (centimeter)
d. none of the above
Q. Which of the following bodies will not be able to emit radiation continuously?
a. a body with very high temperature placed in air medium
b. a body with temperature 0 oC placed in air medium
c. a body with temperature 0 oC placed in vacuum
d. none of the above
Q. When a body receives radiation in the wavelength range of 0.1 to 100 μm (micrometer), then its temperature
a. increases
b. decreases
c. does not change
d. unpredictable
ANSWER: increases
ANSWER: total radiation emitted by the body per unit area and time
ANSWER: the rate of heat transfer from drop-wise condensation is higher than that of film condensation
Q. The conduction heat transfer with combination of transfer of material also is called as
a. material conduction heat transfer
b. convection heat transfer
c. solid convection heat transfer
d. none of the above
Q. According to the Fourier's law of heat conduction, the rate of heat transfer by conduction depends upon
a. area of cross section normal to the heat flow
b. temperature gradient
c. both a. and b.
d. none of the above
ANSWER: change in temperature per unit change in distance in the direction of heat flow
Q. Why is the negative sign introduced in the equation of Fourier's law of heat conduction?
q = – kA (dT / dx)
a. because heat transfer rate is inversely proportional to temperature gradient
b. because value of thermal conductivity k is negative
c. because heat is transferred from higher temperature to lower temperature
d. none of the above
ANSWER: because heat is transferred from higher temperature to lower temperature
Q. The value of thermal conductivity k depends upon
a. the material through which the heat is transferred
b. the intensity of heat energy which is being transferred
c. the area which is parallel to the heat transfer
d. all of the above
Q. The materials which have low thermal conductivity are called as ____________
a. thermal conductors
b. thermal resistors
c. thermal insulators
d. none of the above