Beruflich Dokumente
Kultur Dokumente
MAX31910/11 EV Kit
For pricing, delivery, and ordering information, please contact Maxim Direct
at 1-888-629-4642, or visit Maxim’s website at www.maximintegrated.com. 19-6443; Rev 0; 9/12
MAX31910/11 Evaluation Kit
Hardware Configuration data in the table. Once the Continuous Reads starts,
In this section the user must provide hardware configura- the button text will change to Stop for the user to stop
tion information about the EV kit. Select the 8 Bits radio the reads.
button in the Number of Bits section if MODESEL does
Data
not have a jumper on J6. Select the 16 Bits radio but-
The Data table displays the 8 or 16 bits read from each
ton if MODESEL is connected to GND on J6. If there are
device connected to the EV kit. The first row of data is
more MAX31910/11 daisy chained to the EV kit, select
the first 8 or 16 bits read from the device connected to
the number of devices with the Number of MAX31910/11
the microcontroller. The second row is the data read
combo box.
from the device connected to the SIN of the first device
Reads (see Figure 2). The MAX31910/11 column displays the
To read the input channels of the devices, select Single device name. The device name can be changed by
Read. This will calculate the number of bits to read clicking on the name twice. The HEX column displays the
based on the Hardware Configuration settings and then data in hexadecimal format for each device. The Input
display the read data in the table. Continuous Reads Channels, CRC, UV Alarm, and OT Alarm columns
will read the input channels every 300ms and display the display the data in binary format.
TO MICROCONTROLLER SOUT
MAX31910
MAX31911
SIN
SOUT
MAX31910
MAX31911
SIN
SOUT
MAX31910
MAX31911
SIN
Troubleshooting
All effort was made to ensure that each kit works on the first try, right out of the box. On the rare occasion that a problem
is suspected, refer to the below table to help troubleshoot the issue.
If not, then exit the GUI and try running it again. If D51 still does
GUI says hardware
Does the LED labeled D51 turn not turn green, then exit the GUI and try connecting the USB cable
not found.
green when the GUI is running? to a different USB port on the PC and wait for a Windows message
that states the hardware is ready to use. Run the GUI again.
If not, then the PCB may not be getting power from USB. Try a
Are any of the LEDs illuminated?
different USB cable or a different USB port
CRC returns all 0s Place a jumper on J6 (MODESEL) for the MAX31910/11 to be in
J6 (MODESEL)
or all 1s. 16-bit mode.
Maxim Integrated
RIREF DB1 2 27 SIN 1
DB1 SIN 1
J2 IN1 3 26 MODESEL SIN 2
IIN11
IN MODSEL 2
RT1 4 25 CLK FAULTB 3
1
2
RT1 CLK 3
IN2 5 24 CSB GND SOUT 4
IIN22
IN CSB 4
RT2 6 23 SOUT CSB 5
RT2 SOUT 5
IN3 7 22 IN8 CLK 6
R1 IIN33
IN IIN88
IN 6
RT3 8 21 RT8 5V0 7
15k 1/8w RT3 RT8 R11 7
IN4 9 20 IN7 8
IIN44
IN IIN77
IN 3.3k 8
RT4 10 19 RT7
RT4 RT7
IN5 11 18 IN6 J3
IIN55
IN IIN66
IN D10
Field Power P/N: MMB02070C1500FB200 GND RT5 12 17 RT6
RT5 RT6 LED
24V IN 150 1/3w MEL
F RIREF 13 16 FAULTB
J1 R2 RIREF FAULTB
VCC24V 14 15 5V0
1 VCC24V 5VOUT
2 C1 C2
MAX31910/11
D9 C12 C11 0.1uF 4.7uF
GND 36V ZEN 0.1uF 10uF 100V
2 Screw Terminal Block P/N: 1SMB36AT3G P/N: C5750X7S2A106M
GND GND
GND Layout solder bridges under L
EDS
MAX31910/11 Evaluation Kit
6
Evaluates: MAX31910 and MAX31911
Maxim Integrated
D50A 3900_5V U52 IN01_5V
R50
U50 3900_5V VCCA VCCB
560 Red 6 1 GNDA GNDB
J50 FLAG OUT 3900_SCK IN01_SCK
1 VBUS 5 2 INA OUTA
Vbus I
IN GND D50B 3900_CS IN01_CSB
2 R51 0 D- 4 3 C51 INB OUTB
D- ON SETI 3900_MISO IN01_MISO
3 R52 0 D+ 10uF OUTC INC
Green
D+ 3900_FAULTB IN01_FAULTB
4 MAX4995A OUTD IND
I.D.
5 C50 R62 VCCA VCCB
GND R63
560 GNDA GNDB
USB_5PIN 100K
10uF
DNP - TI ISO7242M/C 0.1uF 50V
C57 C58
0.1uF
3900_GND 3900_GND 3900_GND
IN01_5V 1
1
Only one isolator will be populated 2
2
IN01_SCK3
3900_GND IN01_GND 3
Layout MAX14850 footprint inside ISO7242 IN01_CSB4
4
footprint IN01_MISO
5
5
IN01_FAULTB 6
3900_5V U53 IN01_5V 6
Red
MAX14850
Green
3900_GND IN01_GND
COM
U51
J51 VPP 1 28
MCLR P8,1W_PU
2 HB 2 27 3900_FAULTB R59 IN01_FAULTB
P3,HB P7,1W_DQ
1 COM 3 26 DNP
COM_LED,BOOT P5
DNP 4 25
P1 USB_DET R60
5 24 IN01_SCK
P2 VPO
DNP 6 23 DNP
RCV VMO
IN01_CSB R58 3900_CS 7 22 3900_SCK
3900_GND P6, CS P10,SCK,SCL R61
8 21 3900_MISO IN01_MISO 3900_5V
GND P11,SDI,SDA
R57 0 OSC1 9 20 DNP
OSC1 VDD
10 19
OSC2 GND
X50 3900_5V 11 18 C55 C56
P4 P9,SDO
1 4 12 17
IINH
IN H VCC UOE ENUM
13 16 D+ 1uF 0.1uF
PS_VAR D+,VP
2 3 VUSB 14 15 D-
GND OUT VUSB D-,VM
C53 C54 PICfor DS3900
3900_GND
22pF 220nF
7
Evaluates: MAX31910 and MAX31911
MAX31910/11 Evaluation Kit
Ordering Information
PART TYPE
MAX31910EVKIT# EV Kit
MAX31911EVKIT# EV Kit
#Denotes a RoHS-compliant device that may include lead that
is exempt under the RoHS requirements.
Revision History
REVISION REVISION PAGES
DESCRIPTION
NUMBER DATE CHANGED
0 9/12 Initial release —
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent
licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 13
© 2012 Maxim Integrated Products, Inc. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.