Beruflich Dokumente
Kultur Dokumente
49UH6100 WebOS
W bOS 3.0
3 0 UHD TV
D802
D803
LED- L801 Gnd T-CON fuse. It will not work. Can not use
D201
5 123.7V~109.4V 13.12V Smart Test Jig on this model for T-CON test.
7 LED+ 169.0V~163.6V OL Gnd
Backlight
In Out Dim to Bright Power
Gnd
D204
D206
D205
No Stand-By Voltages Backlights *0% to 100%
D202
D203
Pins 2, 4, 6 are n/c.
13.12V
80V Gnd
Pins 3 and 5 are jumped together T101 P201 "SMPS Board" To P2502 "MAIN Board"
Direct Lit Backlights (LED Array Strips) IC102
PIN LABEL STBY RUN Diode
36 Total LEDs. 4 Strips with 9 LEDs per/strip.
IC103
Secondary P201 (3) 12 P_DIM1 0V *0.18V-3.24V OL
Primary
23.40V SMPS (2) 11 MS (Drv_On) 0V 2.03V OL
IC102 IC103 D107 9-10 Gnd Gnd Gnd Gnd
1) 11.54V 1) 1.10V
P/N: EAY64388811
4-8 13.2V 7.90V 13.11V OL
Chassis 2) 10.52V Chassis 2) 0V D101
Can’t Read
3.15A / 250V 3 Gnd Gnd Gnd Gnd
Gnd Gnd Run: 400V D602
Hot Hot D109 STBY: 186.7V
(3) 2 N/C n/c n/c n/c
Gnd 3) Hot Gnd Gnd 3) 16.87V F101 (1) 1 PWR_ON 0V 3.29V 0.87V
200V 400V
4) 1.50V 4) 20.96V
+
*Dim to Bright
C611
460V
68uF
107.2V
-
CX101
SMPS TEST: Forcing SMPS On. (1) PWR-On Pin 1: Turns on 13.2V to the Main. No
This test requires simple 3V jig. See below.. D601 backlights at this time. Backlight Power is 160.8V.
106V L601
LF103
TH101
(2) MS(DRV_On) Pin 11: Turns on the Backlights.
Remove AC Power. CX102
Disconnect P2502 on Main Board. LF101 Backlight power goes to 169V.
Test 1: Using a 3V jig, Jump 3V to pin 1 (PWR_ON).
BD101
(3) P_DIM#1 Pin 12 and P_DIM#2 Pin 2: Will vary
Apply AC Power. (No Backlights in Test 1) AC
F100 LF102 according to incoming video IRE level and OSD Backlight
(Pins 4-8) rises to 13.14V. Backlight Power 160.8V.
Remove AC Power. P_DIM will be 10.12V
5A / 250V setting Output from the Video Processor. It is then routed
HGnd out P2300 to P201 and sent to the LED Driver IC on the
Back of the SMPS.
Test 2: Using a 3V jig, Jump 3V to pin 11 (DRV_ON). The Range is: 0.18V~3.24V.
Apply AC Power. All Voltages should be produced.
(13.14V to Main and 149.7V to the Backlights).
This will also force the Backlights to come on. SMPS MAIN
All 6 screws are M3X5L (Silver)
P_DIM will be 10.12V P201 P2502
Label Pin Pin Label
P201 Note: SK100 AC Hot Gnd
P_DIM1 12 2
Test 2 11 12 P201 still inserted. P2502 removed. (Shock Hazard)
Use P2502 side to insert resistors. MS 11 1 DRV_ON
2 AA (3V)
LG
September 2016
Page 01
Power Supply Board Low Voltage Test 1 49UH6100 (2016) Power Supply Testing
Note: The numbers in Fig 1 refer to the “Main” board connector (from the SMPS TEST 1
SMPS) that has been unplugged. Use this end for easy insertion of needles. Top Row pins Female side
SMPS connector
t pins
i are the
th same as theth Main
M i on this
thi chassis.
h i are Odd numbers of P2502
AC Should not be applied at any time while adding connectors or while Fig 1
unplugging connectors, damage to the circuit Board may occur.
2 (1.5V Batteries) 11 12
I) When AC is applied, the SMPS “MUST” be producing STBY 7.9V on pins 4-8,
of P201. [Pins 5-8, and 10 on Main P2502]. 9 10
12.2V 7 8 12.2V
If STBY is missing, STBY voltage may be loaded down by the Main Board or the
Joy Stick/IR Board. Remove connector P2502 on Main board from SMPS. If Size: AA 12.2V 5 6 12.2V
STBY is still missing, SMPS is defective but make sure AC is arriving at the
Gnd
connector SK100. 3V 3 4 12.2V
PWR_ON
II) With P2502 on the Main Board unplugged, it will make insertion of the Needle 1 2
tips easier. Use P2502 (Main Board side) to insert connections during these A
tests. Pin numbers will be given from P201 side. Brackets [ ] indicate Main.
STAND-BY VOLTAGE:
7.90V in STBY, 13.11V in Run
TEST 1: TESTING THE POWER SUPPLY TURN-ON CIRCUIT. (See Fig 1)
(1) Using two AA 1.5V batteries hooked in series (3V supply) jump the negative Pin 1 Bottom Front on SMPS
lead to ground (pin 3) [Main pin 9] and the positive lead to PWR-ON (pin 1) Pin 1 is Top Front on Main
[Main pin 11] as shown in example (A) in Fig 1 on the right. Top row is odd pins, bottom row is even pins.
Apply AC, this will turn on the SMPS. No Relay click will be heard.
Check that the 13.2V supplies that go to the Main board turn on; WARNING:
To Main Board Power: Do not to let the leads touch positive (+) to
• [P2502 “13.14V” pins 5-8, 10] negative (–) at any time as this will cause
• (P201 “13.14V” 4-8) battery to overheat creating a fire hazard.
Continue if the 1st test was OK. Leave original jumper (A) in place. SMPS TEST 2
Top Row pins Fig 2 Female side
AC Power is removed at this time
time.
are Odd numbers of P2502
TEST 2: Backlight Section (Using P2502 side)
B
(3) (B) Jump the 3V to Pin 11 MS (DRV_ON). (See Fig. 2), 2 (1.5V Batteries) 11 12
DRV_ON
Simulating a Power On and Backlight On command.
9 10
0
(4) Apply AC Power.
12.2V 7 8 12.2V
Iff the DRV_On O command is pulling up to 3V and the 149.7V is being Generated
G
at P801, suspect a Panel’s Backlight Section problem. Pin 1 Bottom Front on SMPS
Note: If P801 is disconnected, the backlight power will come on, Pin 1 is Top Front on Main
start at 112V climb to 122V and stay there. Top row is odd pins, bottom row is even pins.
48
4-8 13 2V
13.2V 13 14V
13.14V 13 14V
13.14V
Backlight Driver Q801
3 Gnd Gnd Gnd
(3)
Backlight Controller IC is IC801
2 P-DIM#2 0V 0V
(1)
D204 and D206 Backlight Power Source P801 pin 7
1 PWR-ON 3.11V 3.11V
BL Off BL On
D201 and D202 13.2V Source
4-8
48 13.2V
13 2V 7.90V
7 90V 13.11V
13 11V OL
PANEL_CTL
R4121 3.40V
N/C 3.40V
N/C 2 12 N/C P4100 (pin 15) IR 6 IR
100Ω
3 Power Button 3.40V
Gnd R4104
9 3 P4000 (pin 19) Key 2 32 Joy Stick
3.49V 100Ω
Gnd 1 0V when 8
10 4 STBY: 7.90V L2312 Pressed 19
5 RUN: 13.11V
L2502 L2313 6 +3.5V_ST IC3000 1.37V
13.11V Micro
5 7 +13V 8 IC2306 3.48V
C2508/12 R2346 EN 1
STBY: 7.90V 13.11V 1
6 8 10uF 10K 48 6
RUN: 13.11V 12.78V 3.46V
C2505 R3030 Power Det 14
1 13.11V 0.1uF 10K
13.2V 4 10 To IC5800 3.46V 3.48V
5 C3004 40 Reset
13.17V L2503 L2500 Pins 19, 20, 31, 32
0.1uF IC2304
13.11V 2 (pin 2)
7 5 A13V +13V_AMP 13.11V 13.11V
5 Senses
C2511 7 12.2V
13.11V 10uF L2300 IC2302 R2304 10K
8 6 +3.3V_Normal 2 EN 5 33 PWR_ON/
3.39V 3.40V OFF2_1
3.31V 3.31V
Gnd
3 9 R2501 +3.3V_Normal Off: Lo
R2503 On: Hi
100Ω 1K Goes to other circuits
2.03V 3.42V
9 MS 11 1 INV_CTL 19 9
3.49V
0.18V~3.24V R2509 100Ω
10 P-DIM#1 12 2 P_DIM1 AM24 P_DIM
P_DIM 10
3.44V p/p
P-DIM1 (PWM Dimming) can vary according
50% Backlight
to incoming video IRE level, OSD Backlight IC100
Setting. 120Hz
setting. Range 0.18V to 3.24V.
DC: 1.71V Processor