Beruflich Dokumente
Kultur Dokumente
RRV4322
X-HM81-K
X-HM81-K
X-HM81-S
X-HM71-K X-HM71-S
NETWORK CD RECEIVER
XC-HM81-K XC-HM81-S
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model Type Power Requirement Remarks
SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-
yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained
to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
B This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive
harm.
Health & Safety Code Section 25249.6 - Proposition 65
LABEL CHECK
D
SYXE8 model
AXQ5 model
CXE model
2 X-HM81-K
1 2 3 4
5 6 7 8
CONTENTS
SAFETY INFORMATION.......................................................................................................................................................... 2
1. SERVICE PRECAUTIONS .................................................................................................................................................... 4
1.1 NOTES ON SOLDERING ............................................................................................................................................... 4 A
1.2 WHEN REPLACING MECHA ......................................................................................................................................... 4
1.3 WHEN REPLACING CR870 (Module including BCO Assy) ........................................................................................... 4
2. SPECIFICATIONS................................................................................................................................................................. 5
3. BASIC ITEMS FOR SERVICE .............................................................................................................................................. 6
3.1 CHECK POINTS AFTER SERVICING ........................................................................................................................... 6
3.2 JIGS LIST ....................................................................................................................................................................... 6
3.3 PCB LOCATIONS ........................................................................................................................................................... 7
4. BLOCK DIAGRAM .............................................................................................................................................................. 10
4.1 OVERALL WIRING DIAGRAM ..................................................................................................................................... 10
4.2 OVERALL BLOCK DIAGRAM....................................................................................................................................... 12
4.3 POWER SUPPLY BLOCK DIAGRAM........................................................................................................................... 14
5. DIAGNOSIS ........................................................................................................................................................................ 16 B
5.1 TROUBLESHOOTING.................................................................................................................................................. 16
5.2 PROTECTION CIRCUIT............................................................................................................................................... 21
5.3 POWER MANAGEMENT.............................................................................................................................................. 24
5.4 CHECKING TERMINALS ............................................................................................................................................. 25
5.5 IC INFORMATION ........................................................................................................................................................ 28
6. SERVICE MODE ................................................................................................................................................................. 31
6.1 SERVICE MODE .......................................................................................................................................................... 31
6.2 PROTECT CHECK MODE ........................................................................................................................................... 33
6.3 CHECKING THE LCD .................................................................................................................................................. 35
6.4 RDS CHARACTERS..................................................................................................................................................... 36
7. DISASSEMBLY ................................................................................................................................................................... 37
C
8. EACH SETTING AND ADJUSTMENT ................................................................................................................................ 45
8.1 UPDATING OF THE FIRMWARE ................................................................................................................................. 45
8.2 INITIAL SETTINGS....................................................................................................................................................... 51
9. EXPLODED VIEWS AND PARTS LIST............................................................................................................................... 52
9.1 PACKING SECTION ..................................................................................................................................................... 52
9.2 EXTERIOR SECTION .................................................................................................................................................. 54
9.3 SPEAKER SECTION (S-HM81GB, S-HM81SA) .......................................................................................................... 58
9.4 SPAEKER SECTION (S-HM71).................................................................................................................................... 59
10. SCHEMATIC DIAGRAM .................................................................................................................................................... 60
10.1 CD ASSY .................................................................................................................................................................... 60
10.2 TUNER and BT ASSYS.............................................................................................................................................. 62
10.3 MAIN ASSY (1/3)........................................................................................................................................................ 64 D
10.4 MAIN ASSY (2/3)........................................................................................................................................................ 66
10.5 MAIN ASSY (3/3)........................................................................................................................................................ 68
10.6 BCO ASSY (1/2) ......................................................................................................................................................... 70
10.7 BCO ASSY (2/2) ......................................................................................................................................................... 72
10.8 CNT1 ASSY................................................................................................................................................................ 74
10.9 CNT2 ASSY................................................................................................................................................................ 76
10.10 CNT3 ASSY.............................................................................................................................................................. 78
10.11 F_AUX, F_USB, FRONT and KEY ASSYS .............................................................................................................. 80
10.12 DOCKING ASSY ...................................................................................................................................................... 82
10.13 POWER ASSY.......................................................................................................................................................... 84
10.14 WAVEFORMS........................................................................................................................................................... 86
11. PCB CONNECTION DIAGRAM ........................................................................................................................................ 88 E
11.1 CD ASSY .................................................................................................................................................................... 88
11.2 TUNER and BT ASSYS.............................................................................................................................................. 90
11.3 MAIN ASSY ................................................................................................................................................................ 92
11.4 BCO ASSY ................................................................................................................................................................. 96
11.5 CNT1, CNT2 and CNT3 ASSYS................................................................................................................................. 98
11.6 F_AUX, F_USB, FRONT, KEY and DOCKING ASSYS ............................................................................................ 102
11.7 POWER ASSY.......................................................................................................................................................... 106
12. PCB PARTS LIST ............................................................................................................................................................ 108
X-HM81-K 3
5 6 7 8
1 2 3 4
1. SERVICE PRECAUTIONS
1.1 NOTES ON SOLDERING
A • For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.
• Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 ºC.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 ºC in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
B
temperatures (hard to melt/easy to harden).
4 X-HM81-K
1 2 3 4
5 6 7 8
2. SPECIFICATIONS
Amplifier section Speaker (X-HM81 only) A
RMS Power Output ..................................................... 50 W + 50 W Type
(1 kHz, 10 % T.H.D., 4 ohms) 2-way type speaker system
Guaranteed speaker impedance ....................... 4 ohms to 16 ohms 2.5 cm Dome-Tweeter
Headphones .............................................. recommended: 32 ohms 12 cm Woofer
Maximum input power ..............................................................50 W
Tuner section Impedance............................................................................ 4 ohms
Frequency Range (FM) ................................ 87.5 MHz to 108 MHz Dimensions
Antenna Input (FM).........................................75 ohms unbalanced Width ................................................................................ 156 mm
Frequency Range (AM) ..................................522 kHz to 1602 kHz Height ............................................................................... 266 mm
Antenna (AM) ............................................................ Loop antenna Depth ................................................................................ 258 mm
Weight ........................................................................... 4.3 kg/each
Video section
Signal level (Composite)...................................... 1 Vp-p (75 ohms) Speaker (X-HM71 only)
B
Type
Network section 2-way type speaker system
LAN terminal................................................................ Ethernet jack 2 cm Dome-Tweeter
10BASE-T/100BASE-TX 12 cm Woofer
Maximum input power ..............................................................50 W
Other connectors Impedance............................................................................ 4 ohms
Power supply Dimensions
USB connector ...............................................................5 V, 2.1 A Width ................................................................................ 148 mm
iPod connector................................................................5 V, 1.0 A Height ............................................................................... 263 mm
ADAPTER Port (X-HM81 and XC-HM81 only) ...............5 V, 0.1 A Depth ................................................................................ 208 mm
Weight ........................................................................... 2.7 kg/each
Miscellaneous
Power source............................................AC 220 V to 240 V, 50 Hz Note
Power consumption • The specifications are applicable when the power supply is 230 V. C
Power on................................................................................75 W • Specifications and the design are subject to possible
Power standby.......................................................... 0.5 W or less modifications without notice, due to improvements.
Network standby....................................................................17 W • Corporation and product names mentioned herein are
Dimensions trademarks or registered trademarks of the respective
Width ................................................................................ 215 mm corporations.
Height (X-HM71).............................................................. 131 mm • This product is not designed for use in Japan.
Height (X-HM81 and XC-HM81)...................................... 32.2 mm • This product includes FontAvenue® fonts licensed by NEC
Depth ................................................................................ 353 mm Corporation. FontAvenue® is a registered trademark of NEC
Weight (X-HM71)................................................................... 5.0 kg Corporation.
Weight (X-HM81 and XC-HM81) ............................................ 5.5 kg
Accessories
X-HM81-K 5
5 6 7 8
1 2 3 4
See the table below for the items to be checked regarding audio.
Item to be checked regarding audio
Distortion
C Noise
Volume fluctuating
Sound interrupted
6 X-HM81-K
1 2 3 4
5 6 7 8
A
BCO_STOPPER ASSY
C BT ASSY
(X-HM81 only)
MAIN ASSY D
E BCO ASSY
B TUNER ASSY
B
CD ASSY A
F CNT1 ASSY
C
F_USB ASSY J L KEY ASSY
M DOCKING ASSY
F_AUX ASSY I
FRONT ASSY K
X-HM81-K 7
5 6 7 8
1 2 3 4
A NOTES: - Parts marked by “NSP” are generally unavailable because they are not in our Master Spare Parts List.
- The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
LIST OF ASSEMBLIES
X-HM81-K X-HM81-S XC-HM81-K XC-HM81-S
Mark Symbol and Description
/SYXE8 /SYXE8 /SYXE8 /SYXE8
NSP 1..PCB TOTAL ASSY FRONT 7025MU1105030-IL 7025MU1105030-IL 7025MU1105030-IL 7025MU1105030-IL
2..FRONT ASSY 7028072531010-IL 7028072531010-IL 7028072531010-IL 7028072531010-IL
NSP 2..CNT1 ASSY ••••• ••••• ••••• •••••
2..KEY ASSY 7028072533010-IL 7028072533010-IL 7028072533010-IL 7028072533010-IL
B 2..TUNER ASSY 7028072534030-IL 7028072534030-IL 7028072534030-IL 7028072534030-IL
8 X-HM81-K
1 2 3 4
5 6 7 8
X-HM81-K 9
5 6 7 8
1 2 3 4
4. BLOCK DIAGRAM
4.1 OVERALL WIRING DIAGRAM
A - When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST".
- The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation. (7028072534030-IL: X-HM81, XC-HM81)
- : The power supply is shown with the marked box. (7028072534060-IL: X-HM71/SYXE8)
(7028072534040-IL: X-HM71/CXE, AXQ5)
CP8
1: BT
2: AG
1: VIDEO_GND
2: VIDEO_GND
3: DOCK_CVBS
B TUNER ASSY
3: BT
4: GN
5: SU
6: SU
9: CSK_MAIN 9: DB7/G1
14: DB12/R0
15: DB13/R1
14: A_GND
15: BT/TU_R
25: TU_+5V CP400 10: SCDO_MAIN 10: DB8/G2
16: DB14/R2 16: A_GND CP512 11: SCDI_MAIN
12: MAIN_IRQ
11: DB9/G3
12: DB10/G4
17: DB15/R3 17: BT/TU_L 1: VFD_CE 13: DOCKING_CVBS 13: DB11/G5
18: DB16/R4 18: A_GND 2: VFD_CLK 14: MAIN_USB_POWER 14: DB12/R0
19: DB17/R5 19: VIDEO_MUTE 3: VFD_DI 15: VGND 15: DB13/R1
20: SCL 20: SW_MUTEBASE 16: DM-870-SCLK 16: DB14/R2
21: DE 21: TU_RST(DAB_RST) 17: DM-870-MCLK 17: DB15/R3
22: CSX
23: DOTCLK
22: TU_SEN
23: TU_SCLK
CP19 18: DM-870-LRCK 18: DB16/R4
19: DM-870-DATA 19: DB17/R5
24: HSYNC 24: SDIO DAB_RX 1: SW_GND 11: A_GND 1: SW_GND 20: VFD_DI 20: CSX
25: VSYNC 25: GPIO2 DAB_TX 2: SW_OUT 12: LINE_IN_R 2: SW_OUT 21: VFD_CLK 21: SCL
26: SDA 26: I_POD_DET 3: A_GND 13: A_GND 3: A_GND 22: VFD_CE 22: DE
27: LED-A+ 27: CSCK_MAIN 4: BT/TU_R 14: LINE_IN_L 4: BT/TU_R 23: AMP-5V 23: DOTCLK(GND_S
28: LED-CTL 28: SCDO_MAIN 5: A_GND 15: A_GND 5: A_GND 24: AMP+5V 24: HSYNC
29: IOVCC(+3.3V) 29: SCDI_MAIN 6: BT/TU_L 16: A_GND 6: BT/TU_L 25: NC 25: VSYNC
30: IOVCC(+3.3V) 30: MAIN_IRQ 7: A_GND 17: A_GND 7: A_GND 26: SDA
31: GND 31: SUB_RESET 8: USB_R 18: +12V 8: USB_R 27: LED-A+
32: GND 32: SUB_ON 9: A_GND 19: +12V 9: A_GND 28: LED-CTL(SPSW
33: SUB_PDN 33: SUB_IRQ 10: USB_L 10: USB_L 29: IOVCC(+3.3V)
11: A_GND 30: IOVCC(+3.3V)
12: LINE_IN_R 31: GND
CP606 13: A_GND 32: GND
CP30 CP31 14: LINE_IN_L
15: A_GND
33: GND
16: A_GND
17: A_GND
18: +12V
19: +12V
C
H
CNT3 ASSY
CP604
1: +12V
2: +12V
CP18 3: A_GND
1: DAC_RST 17: SW_MUTEBASE 4: A_GND
2: AUDIO_SEL 18: VIDEO_MUTE 5: -12V
6: -12V
CP605
3: SUB_PDN 19: IPOD_CHARGE_LED 1: B+_27V
4: SUB_IRQ 20: POWER_ON_LED 7: A_GND
8: CD_L 2: B+_27V
5: SUB_ON 21: KEY2 3: AMP_GND
9: A_GND
6: SUB_RESET
7: MAIN_IRQ
22: KEY1
23: REMOTE 10: CD_R 4: AMP_GND CP712
11: M_GND 5: LCH_AMP_GND
8: SCDI_MAIN 24: TIMER_LED 6: LCH_AMP_GND
12: M_GND
9: SCDO_MAIN
10: CSCK_MAIN
25: VOLUME+
26: VOLUME- 13: CD_RX 7: RCH_AMP_GND CN702
14: CD_TX 8: RCH_AMP_GND
11: I_POD_DET 27: M3V3 9: B-_27V
12: GPIO2_DAB_RX 28: M3V3_SW 15: CD_RST
16: MAIN_BUSY 10: B-_27V
13: SDIO_DAB_TX 29: CPU_GND 11: RLY_GND 1: B+_27V 14: AMP_-5V
14: TU_SCLK 30: CPU_GND 17: NC 2: B+_27V 15: AMP_+5V
12: RLY_GND
15: TU_SEN 31: CPU_GND 13: AMP_-5V 3: AMP_GND 16: POWER_PROT
16: TU/DAB_RST 14: AMP_-5V 4: AMP_GND 17: P/D
5: AMP_GND_L 18: STBY_RLY
FPC2 15: POWER_PROT
16: AMP_+5V 6: AMP_GND_L 19: M_GND
1: CPU_GND 21: DB9/G3 17: PD 7: AMP_GND_R 20: M_GND
2: M3V3_SW 22: DB10/G4 18: STBY_RLY 8: AMP_GND_R 21: MICOM_3V9
3: M3V3 23: DB11/G5 CP607 19: M_GND 9: B-_27V 22: MICOM_3V9
D 4: KEY2 24: DB12/R0 1: LCDGND CP509 20: M_GND 10: B-_27V
11: SPKRLY_GND
23: DGND
24: DGND
5: KEY1 25: DB13/R1 2: LCDGND 21: MICOM_3V9
6: CPU_GND 26: DB14/R2 1: DAC_RST 22: MICOM_3V9 12: SPKRLY_GND 25: NC
3: IOVCC(+3.3V) 2: AUDIO_SEL 13: AMP_-5V 26: NC
7: REMOTE 27: DB15/R3 4: IOVCC(+3.3V) 23: DGND
8: TIMER_LED 28: DB16/R4 3: SUB_PDN 24: DGND
9: VOLUME+ 29: DB17/R5 4: SUB_IRQ 25: NC
10: VOLUME- 30: CSX 5: SUB_ON 26: NC
11: RESX 31: SCL 6: SUB_RESET
12: DB0/B0 32: DE 7: MAIN_IRQ
13: DB1/B1 33: DOTCLK 8: SCDI_MAIN
16: TU/DAB_RST
2: H/P_GND
4: H/P_GND
5: FAUX_R
8: HP_DET
7: FAUX_L
17: SW_MUTEBASE
1: HP_R
3: HP_L
4: H/P_GND
5: FAUX_R
7: FAUX_L
8: HP/DET
3: HP_L
I
30: CPU_GND 6: A_-12V
31: CPU_GND 7: A_GND
8: CD_L
9: A_GND
CP602 10: CD_R
E 11: M_GND
PN1702
FPC515 CN515
3: IOVCC(+3.3V)
4: IOVCC(+3.3V)
8: TIMER_LED
10: VOLUME-
2: M3V3_SW
1: CPU_GND
6: CPU_GND
9: VOLUME+
22: DB10/G4
23: DB11/G5
24: DB12/R0
25: DB13/R1
26: DB14/R2
27: DB15/R3
28: DB16/R4
29: DB17/R5
38: LED-CTL
33: DOTCLK
18: DB6/G0
19: DB7/G1
20: DB8/G2
21: DB9/G3
7: REMOTE
12: DB0/B0
13: DB1/B1
14: DB2/B2
15: DB3/B3
16: DB4/B4
17: DB5/B5
37: LED-A+
34: HSYNC
35: VSYNC
39: LED_B
40: LED_A
11: RESX
3: M3V3
36: SDA
30: CSX
4: KEY2
5: KEY1
31: SCL
CP500
32: DE
1: GND
2: GND
K
4: USBHO_D+
3: USBHO_D-
5: USB_GND
6: USB_GND
1: USB_VCC
2: USB_VCC
FRONT ASSY
7: NC
MOD500
(7028072531010-IL)
34: IOVCC(+3.3V)
2: VCI(+3.3V)
14: DB10/G4
15: DB11/G5
16: DB12/R0
17: DB13/R1
18: DB14/R2
19: DB15/R3
20: DB16/R4
21: DB17/R5
25: DOTCLK
10: DB6/G0
11: DB7/G1
12: DB8/G2
13: DB9/G3
29: LED-A+
30: LED-K1
31: LED-K2
32: LED-K3
33: LED-K4
26: HSYNC
27: VSYNC
1: CPU_GND
4: DB0/B0
5: DB1/B1
6: DB2/B2
7: DB3/B3
8: DB4/B4
9: DB5/B5
J
35: GND
3: RESX
28: SDA
22: CSX
23: SCL
1: GND
24: DE
2: KEY2
F
CP508
F_USB ASSY LCD
(7028072536010-IL)
10 X-HM81-K
1 2 3 4
5 6 7 8
X-HM81, A
E E 1/2- E 2/2 XC-HM81
C
10: BT_TX/U_RX
11: BT_RX/U_TX
BCO ASSY
6: BT_ON/CE
5: BCO_GND
1: BT_MUTE
12: BT_/OC
-HM81, XC-HM81) ONLY
9: BT_DET
7: BT_+5V
3: A_GND
8: BT_ID
2: BT_R
4: BT_L
-HM71/SYXE8) (7028072551010-IL: X-HM81, XC-HM81) BT ASSY
-HM71/CXE, AXQ5) (7028072551020-IL: X-HM71) CP1001
(7028072537010-IL)
10: BT_TX/U_RX
11: BT_RX/U_TX
CP8 CP6
6: BT_ON/CE
5: BCO_GND
1: BT_MUTE
1: BT_R
12: BT_/OC
9: BT_DET
7: BT_+5V
2: AGND
8: BT_ID
3: AGND
2: BT_R
4: BT_L
3: BT_L
5: GND
6: GND
1: +5V
2: +5V
4: D+
3: D-
9: CSK_MAIN
10: SCDO_MAIN
11: SCDI_MAIN
12: MAIN_IRQ CP5
7: IPOD_CVBS
1: GND CP301
6: IPOD_DET
8: MIITXCLK
13: IPOD_CVBS
14: MAIN_USB_POWER (NC) 2: GND
15: VGND 3: GND
4: GND
5: GND
3: +5V
4: VDD
2: D+
16: DM-870-SCLK
1: D-
17: DM-870-MCLK 5: VDD CP7
M DOCKING ASSY
6: VDD
P12 CP11 18: DM-870-LRCK
19: DM-870-DATA 7: +5V CP1
1: GND
2: GND
BT_R 1: RESX 8: -5V
AGND
BT_L
AGND
2: DB0/B0
3: DB1/B1
4: DB2/B2
20: VFD_DI
21: VFD_CLK
22: VFD_CE
3: GND
4: IOVCC(+3.3V)
5: IOVCC(+3.3V)
(7028072544010-IL) B
23: AMP-5V 6: LED-CTL(SPSW)
SUB_IRQ 5: DB3/B3 24: AMP+5V 7: LED-A+
1: ACCESSORY_PWR
SUB_RESET 6: DB4/B4 25: AMP+5V 8: SDA CP4
SUB_PDN 7: DB5/B5 9: VSYNC
MAIN_SUB_IPOD_DET 8: DB6/G0 10: HSYNC
3: IPOD_DET
CSK_MAIN 9: DB7/G1
6: USB_+5V
11: DOTCLK
7: USB_D+
8: USB_D-
4: D_GND
5: D_GND
: SCDO_MAIN 10: DB8/G2 12: DE
2: C_VID
: SCDI_MAIN
: MAIN_IRQ
11: DB9/G3
12: DB10/G4
CP8 CP7 13: CLK
14: CSX
N
: DOCKING_CVBS 13: DB11/G5 15: DB17/R5
: MAIN_USB_POWER 14: DB12/R0 16: DB16/R4
: VGND 15: DB13/R1 17: DB15/R3
: DM-870-SCLK 16: DB14/R2 18: DB14/R2
: DM-870-MCLK 17: DB15/R3 19: DB13/R1
: DM-870-LRCK 18: DB16/R4 20: DB12/R0
: DM-870-DATA
: VFD_DI
: VFD_CLK
19: DB17/R5
20: CSX
21: SCL
21: DB11/G5
22: DB10/G4
23: DB9/G3
POWER ASSY
CP402 CP505 CP506
: VFD_CE
: AMP-5V
: AMP+5V
22: DE
23: DOTCLK(GND_SHIELD)
24: HSYNC
24: DB8/G2
25: DB7/G1
26: DB6/G0
1: VIDEO_GND
2: VIDEO_GND
1: USB_R
2: A_GND
1: RESX
2: DB0/B0
(7028072542030-IL:
: NC 25: VSYNC
26: SDA
27: LED-A+
CP12 CP11 27: DB5/B5
28: DB4/B4
29: DB3/B3
3: DOCK_CVBS
4: SW_GND
5: SW_OUT
3: USB_L
4: +12V
5: +12V
3: DB1/B1
4: DB2/B2
5: DB3/B3
X-HM81,XC-HM81)
28: LED-CTL(SPSW)
29: IOVCC(+3.3V)
30: IOVCC(+3.3V)
CP402 30: DB2/B2
31: DB1/B1
32: DB0/B0
6: A_GND
7: LINE_IN_R
6: DAC_RESET
7: AUDIO_SEL
6: DB4/B4
7: DB5/B5
(7028072542030-IL:
31: GND
32: GND
33: GND
33: RESX
8: A_GND
9: LINE_IN_L
10: A_GND
8: SW_GND
9: SW_OUT
10: A_GND
8: DB6/G0
9: DB7/G1
10: DB8/G2
X-HM71/SYXE8, AXQ5)
11: DAB/TU_R
12: A_GND
13: DAB/TU_L
11: LINE_IN_R
12: A_GND
13: LINE_IN_L
11: DB9/G3
12: DB10/G4
13: DB11/G5
(7028072542040-IL:
1: VFD_DI
2: VFD_CLK
3: VFD_CE
14: A_GND
15: VIDEO_MUTE
16: SW_MUTEBASE
14: A_GND
15: BT/TU_R
16: A_GND
14: DB12/R0
15: DB13/R1
16: DB14/R2
X-HM71/CXE)
CN511 17: TU/DAB_RST 17: BT/TU_L 17: DB15/R3
18: TU_SEN
19: TU_SCLK
18: A_GND
19: VIDEO_MUTE
18: DB16/R4
19: DB17/R5
C
CP505 CP506 20: DAB_RX GPIO2 20: SW_MUTEBASE 20: SCL
21: DAB_TX SDIO 21: TU_RST(DAB_RST) 21: DE
22: A_GND 22: TU_SEN 22: CSX
23: A_GND 23: TU_SCLK 23: DOTCLK
24: TU_+5V 24: SDIO DAB_RX 24: HSYNC
25: TU_+5V 25: GPIO2 DAB_TX 25: VSYNC
26: I_POD_DET 26: SDA
27: CSCK_MAIN 27: LED-A+
28: SCDO_MAIN 28: LED-CTL
29: SCDI_MAIN 29: IOVCC(+3.3V)
5: CD3.3V_GND
CN702 2: MICOM_3V9
3: M_GND
17: AMP_GND_R
18: AMP_GND_R
6: P/D
7: NC
6: CD3.3V_GND
7: CD_3.3V
2: +5V
1: -5V
F
2: B+_27V 15: AMP_+5V 7: NC 22: AMP_GND 11: AMP_-5V
3: AMP_GND 16: POWER_PROT 11: A_+12V
CNT1 ASSY
8: POWER_PROT 23: B+_27V 12: AMP_-5V 12: A_GND
4: AMP_GND 17: P/D 9: AMP_+5V 24: B+_27V 13: SPKRLY_GND
5: AMP_GND_L 18: STBY_RLY 13: A_GND
10: AMP_+5V 25: BCO_GND 14: SPKRLY_GND 14: A_-12V
6: AMP_GND_L 19: M_GND 11: AMP_-5V 26: BCO_GND 15: B-_27V
7: AMP_GND_R 20: M_GND 15: A_-12V
12: AMP_-5V 27: BCO_GND 16: B-_27V
8: AMP_GND_R 21: MICOM_3V9 13: SPKRLY_GND 28: BCO_+12V 17: AMP_GND
9: B-_27V 22: MICOM_3V9 14: SPKRLY_GND 29: BCO_+12V 18: AMP_GND
10: B-_27V
11: SPKRLY_GND
23: DGND
24: DGND
15: B-_27V 30: BCO_+12V 19: AMP_GND
20: AMP_GND
D
12: SPKRLY_GND 25: NC 21: AMP_GND
13: AMP_-5V 26: NC 22: AMP_GND
23: B+_27V
24: B+_27V
25: BCO_GND
26: BCO_GND
27: BCO_GND
28: BCO_+12V
29: BCO_+12V
30: BCO_+12V
PN1602
15: SVCC
16: VREF
8: GND
5: PD
6: VR
7: LD
13: D
10: C
11: B
12: A
2: T+
14: E
4: F+
3: T-
1: F-
9: F
1: A_+12V
2: A_+12V
3: A_GND
4: A_GND
5: A_-12V
6: A_-12V
7: A_GND
8: CD_L
A 1: MOTRO_GND
2: MOTRO_GND
3: MOTRO_+8V
4: MOTRO_+8V
CD ASSY
5: CD_GND
9: A_GND 6: CD_GND
10: CD_R
1: CLOSE_SW
7: CD_3V3
3: OPEN_SW
4: MOTOR_+
5: MOTOR_-
5: Limit SW
3: SL+
2: GND
13: CD_RX
2: SP-
4: SL-
10: A_+12V
14: CD_TX 11: A_+12V
15: CD_RST 12: A_GND
16: MAIN_BUSY 13: A_GND
17: NC PN1604 PN1603 14: A_-12V
15: A_-12V
PN1702
PN1705
KEY ASSY
L (7028072533010-IL)
-IL)
1: CPU_GND
2: KEY2
1: CPU_GND
MECHA
2: KEY2
CN502 F
CP508 (8030000010080-IL)
X-HM81-K 11
5 6 7 8
1 2 3 4
A
D MAIN ASSY
Note: Be blocks in MAIN ASSY other than blocks.
(There are some exceptions)
B IC603
NJU7391
IC704
INPUT SELECT & VOLUME
IC208
G CNT2 ASSY
C
IC12, 18, 19
CR870
IC4
NAND_Flash SDRAM
E BCO ASSY
IC609
LCD
SYSTEM U
E
M3030
LCD
KEY
K FRONT ASSY
12 X-HM81-K
1 2 3 4
5 6 7 8
Headphone
IC605 OUT
IC606
Subwoofer
OUT
B TUNER ASSY
IC400
-6dB D
DOCKING_VIDEO
+6dB
CVBS
OUT
CD BLOCK
A CD ASSY
IC609
SYSTEM U-com
M30302 E
IC1606
IC1604
IC1601
IC1603
IC1602
RMC500
IR
F
SY
X-HM81-K 13
5 6 7 8
1 2 3 4
B+_27V
S1(AMP +B)
B-_27V
IC301
B
S2(+12V,-12V)
IC303
BCO_+12V
MAIN TRANS
S3(USB/CD)
IC311 MOT_+8V
AC CORD
IC315
MICOM_
SUB TRANS
14 X-HM81-K
1 2 3 4
5 6 7 8
AMP_+5V
-33V(NO LOAD)
B-_27V
AMP_-5V
A_+12V
IC301
B
IC305
IC701
IC307
A_-12V
IC303
IC9 IC11
C
IC13
BCO_+12V
IC14
IC5
IC2
CD_+3.3V
D
IC315
MICOM_3V9
X-HM81-K 15
5 6 7 8
1 2 3 4
5. DIAGNOSIS
5.1 TROUBLESHOOTING
A
• No Power
No
C Does Yes
OVERTEMP1 protect • Detection abnormal temperature of the AMP L ch circuit.
work? Check the IC608 and its peripheral circuits. (MAIN Assy)
No
No
D No
X-HM81, XC-HM81 only
No
E
Be not the trouble that each Protect circuit works.
16 X-HM81-K
1 2 3 4
5 6 7 8
A
MAIN UCOM
Is the
output voltage of the regulator No
IC (IC315) for microcomputer power Check the IC315 and its peripheral circuits. (POWER Assy)
supply 3.9 V?
(POWER Assy)
Yes
Does
the oscillator (XTAL600) for No
MAIN UCOM (IC601) oscillate Check the XTAL600 and its peripheral circuits. (MAIN Assy)
it?
(MAIN Assy)
Yes
Check the IC601 and its peripheral circuits. (MAIN Assy)
• No Sound
C
A sound does not come out
of FRONT SP
Does
a signal output it from No • Check the IC602 and its peripheral circuits. (MAIN Assy)
OP-AMP IC (IC602) • Check the MAIN MUTE circuit.
pin 1, 7?
(MAIN Assy)
Yes D
Does
a signal output it from No • Check the IC608, IC612 and its peripheral circuits. (MAIN Assy)
AMP IC (IC608, 612) • Check the Q621, Q623, Q640, Q641 and its peripheral circuits.
pin 13? (MAIN Assy)
(MAIN Assy)
Yes
• Check the speaker realy. (MAIN Assy)
Output it depending on input • Check the input blocks and its peripheral circuits and power
supply voltages. F
• Replace the CR870 (MODULE on BCO Assy).
X-HM81-K 17
5 6 7 8
1 2 3 4
A
When you
A sound does not come out connected HP, do hear the No
working sound of the SP relay • Check the HP DET signal and its peripheral circuits.
of headphones
(a snick sound)?
Yes
Does
a signal output it from No
HP AMP IC (IC605) • Check the IC605 and its peripheral circuits. (MAIN Assy)
pin 1, 7?
(MAIN Assy)
Yes
• Check the HP MUTE circuit. (MAIN Assy)
• Check the connection between the MAIN Assy and F_AUX Assy.
Does
B No
A sound does not come out a signal output it from
• Check the IC606 and its peripheral circuits. (MAIN Assy)
of SW PREOUT OP-AMP IC (IC606)
pin 7?
(MAIN Assy)
Yes
• Check the SW MUTE circuit. (TUNER Assy)
• Check connection between each Assy.
C Is the
cable arranged neatly No • Check whether a cable is arranged neatly.
arround CD tray section? (A cable do not touch a Disc rotate section)
Yes
Is the
power supply voltage of No
• Check the IC311 and its peripheral circuits. (POWER Assy)
the BTL driver (IC1606)
8 V?
Yes (CD Assy)
Is the power
supply voltage of the CD UCOM No
• Check the IC313 and its peripheral circuits. (POWER Assy)
(IC1604), CD DSP (IC1601)
3.3 V?
Yes (CD Assy)
D
Does
the oscillator (X1602) for No
• Check the IC1604, X1602 and its peripheral circuits. (CD Assy)
CD UCOM oscillate it?
Does
the oscillator (X1601) for No
• Check the IC1601, X1601 and its peripheral circuits. (CD Assy)
CD DSP (IC1601) oscillate
it?
Yes (CD Assy)
Does a
signal output it from CD DSP No
• Check the IC1601, X1601 and its peripheral circuits. (CD Assy)
(IC1601) pin 14
(DCLK)?
E Yes (CD Assy)
Is the signal No • Check the IC1604 and its peripheral circuits. (CD Assy)
of CD UCOM (IC1604) pin 40
• Check the IC601 pin 51 (CD RESET signal). (MAIN Assy)
(CD RESET) "H"?
Yes (CD Assy)
Is the signal No
of CD UCOM (IC1604) pin 9 • Check the IC1604 and its peripheral circuits. (CD Assy)
(8035 RESET) "H"?
Yes (CD Assy)
Does signals
output from CD UCOM (IC1604) No
• Check the IC1604 and its peripheral circuits. (CD Assy)
pin 25, 27, 28 (MAIN_BUSY,
F CD_RX, CD_TX)?
(CD Assy)
Yes
• Check the IC1601, IC1606 and its peripheral circuits. (CD Assy)
18 X-HM81-K
1 2 3 4
5 6 7 8
Is the No
reset signal of LCD normal? • Check the connection between the BCO Assy and FRONT Assy.
If MOD500-Pin 3 is "H", its • Check the IC4 and its peripheral circuits. (BCO Assy)
normal.
(FRONT Assy)
Yes
Are the No
other signals of MOD500 • Check the connection between the BCO Assy and FRONT Assy.
normal?
Yes D
• Replace the LCD MODULE.
Is there USB No • Check the connection between the F_USB Assy and BCO Assy.
signal at 3 and 4 Pins of • Check the IC12 and its peripheral circuits. (BCO Assy)
CP500? • Replace the CR870 (MODULE on BCO Assy).
Yes
• Replace the CR870 (MODULE on BCO Assy).
X-HM81-K 19
5 6 7 8
1 2 3 4
A
• Do not recognize it in iPod Dock
No Cannot recognize physical connection of iPod/iPhone.
Does the Charge LED • Check the path of the iPod DET signal between Pin 1 of CP1 (DOCKING Assy)
light? and Pin 55 of IC609 (MAIN Assy). ("L" is normal at iPod/iPhone is connected).
Yes
Is the No
5V power supply supplied • Check the connection between the DOCKING Assy and BCO Assy.
in 23 Pin of CP1? • Check the IC13 and its peripheral circuits. (BCO Assy)
(DOCKING Assy)
Yes
B
Is there USB No • Check the connection between the DOCKING Assy and BCO Assy.
signal at 25 and 27 Pins of • Check the IC12 and its peripheral circuits. (BCO Assy)
CP1? • Replace the CR870 (MODULE on BCO Assy).
Yes
Does a
CVBS signal output to No • Check the connection between the DOCKING Assy and
connector (CP4) TUNER Assy.
pin 2?
(DOCKING Assy)
Yes
20 X-HM81-K
1 2 3 4
5 6 7 8
If a protection circuit is activated then the unit enters Standby mode, the LED flashes in accordance with the activated A
protection function, as shown in the table below.
C
Description of Each Function
• DC Protect
The DC outputs from AMP_OUT_L and AMP_OUT_R are detected to avoid DC current surge to the speakers and excess
voltage at B+ (+33 V).
The protection circuit is activated when the signal at Pin 3 of IC601 changes from H to L.
D MAIN ASSY
AMP_OUT_R
AMP_OUT_L
M3V3_SW
D
B+
R602
MAIN_MICOM
IC601_3 pin 3 DC_PROTECT
DC_PROTECT D620 KTC3198
Q639
KDS4148U C731
R867
R824
100N-K
100K
R826
KTA1268
MTZ22B 47K(1/4)
Q635
Q636
KTC3198
R827
10K
X-HM81-K 21
5 6 7 8
1 2 3 4
A • Power Protect
The protection circuit is activated when short-circuiting is detected at the regulator output.
The circuit is activated when the signal at Pin 4 of IC601 changes from H to L.
Detected power: B+_27V, B-_27V, AMP_+5V, AMP_-5V, MICOM_3V9, A_+12V, A_-12V, CD_3.3V
Note: The above names are the indications on the POWER Assy. The indications of power may be different on other
Assys.
M3V3_SW
R660
B MAIN_MICOM
POWER_PROT 4 IC601_4 pin
To POWER_PROT
Power supply,
Regulator
• AMP_PROTECT
The protection circuit is activated when excess current is detected from the AMP.
The circuit is activated when the signal at Pin 78 of IC601 changes from L to H.
C
MODE1
MAIN_MICOM IC608
IC601_78 pin 78 AMP_PROTECT_DET or
SELF IC612
DC_PROTECT
R606
• OVER_TEMPERATURE_PROTECT_1
E
The protection circuit is activated when abnormally high temperature is detected by the P600 PTC thermistor near IC608
(AMP_Lch).
The circuit is activated when the signal at Pin 92 of IC601 changes from H to L.
D MAIN ASSY
M3V3_SW
R751
P600
MAIN_MICOM
IC601_92 pin
OTP1 92 OVER_
F TEMPERATURE_
R748
PROTECT_1
22 X-HM81-K
1 2 3 4
5 6 7 8
• OVER_TEMPERATURE_PROTECT_2 A
The protection circuit is activated when abnormally high temperature is detected by the P601 PTC thermistor near IC612
(AMP_Rch).
The circuit is activated when the signal at Pin 93 of IC601 changes from H to L.
D MAIN ASSY
M3V3_SW
R788
P601
MAIN_MICOM
IC601_93 pin
OTP2 93 OVER_ B
TEMPERATURE_
R787
PROTECT_2
• PWM_PROTECT
The protection circuit is activated when abnormally PWM output is detected in the AMP_OUT_L and AMP_OUT_R.
The circuit is activated when the signal at Pin 2 of IC601 changes from H to L.
M3V3_SW
D MAIN ASSY
R608
C728 D621 MAIN_MICOM
C
68N
R821
1SS355
100K
IC1
R256
BTSW DM870
IC600_4 pin BT_OL 104 Y14 Y14 MICRS
E
• USB_OVERLOAD_PROTECT
The protection circuit is activated when overcurrent (USB: 2.1 A or over, iPod Dock: 1 A or over) of 5 V power supply of
Front USB or iPod Dock.
The circuit is activated when the signal at Pin 70 of IC1 changes from H to L.
E BCO ASSY BCO MODULE (CR870)
D3.3V
IC1
R26
F_USB SW DM870
IC11_8 pin FAULT 70 M2 M2 VCO0
F
DOCKING SW
IC14_8 pin
X-HM81-K 23
5 6 7 8
1 2 3 4
A
The power supply state transition of this unit becomes the right figure.
Cold Standby:
Mode in which power consumption becomes lowest Cold
Only the main microcomputer among all the microcomputers Standby
3
is powered. 9 4
Power On:
Mode in which AC Relay is turned ON and all microcomputers Network iPod
Standby 1 2 Charge
are powered
iPod Charge:
B 5 7
Mode in which an iPod is inserted in its dock in modes other
6 8
than Power On PowerOn
In this mode, an iPod device that is plugged into the USB
terminal or the dock can be charged.
The power-supply status is the same as that during
power-on with an HP inserted.
Network Standby:
Mode in which the LCD is unlit with Bco powered in order to
save startup time of Bco
The audio and video output signals are muted, and the keys
C
and buttons other than the STANDBY/ON key are masked.
Basically, this mode is the same as iPod Charge mode.
Note: The power-off status caused by activation of a protection circuit is not described in this section. See "5.2 Protection circuit."
24 X-HM81-K
1 2 3 4
5 6 7 8
A
1. Checking the LAN terminal
Connect the PC and this unit directly then set them up as indicated below. Then, access this unit from the PC via a Web
browser. If the indications shown in the figure below are displayed, the LAN terminal is normal.
If the LAN terminal is not normal, check the circuit between the LAN terminal and CR870 (Module on BCO Assy).
X-HM81-K 25
5 6 7 8
1 2 3 4
A Start the Web browser, input http://192.168.0.1 as a URL. If the screen as indicated below is displayed,
the LAN terminal works properly.
Note:
As the SSID name for a wireless LAN router supports only
F
one-byte alphanumerics, if two-byte characters are used in
an SSID name, rename it.
26 X-HM81-K
1 2 3 4
5 6 7 8
A
3. Checking the BT Adapter Terminal
If you connect the AS-BT100 or AS-BT200 as shown in the following steps, you can recognize if this unit works properly:
1. Select the BT function, connect the AS-BT100 or AS-BT200, then check that the indication changes as shown in the
figure below.
If the indication does not change as shown in the above figure, possible causes are as follows:
2. If the indication changes properly in Step 1, perform pairing with a player then check the audio output signals.
If no audio signal is output, check BT_L, BT_R, and BT_MUTE.
1. Select the USB function then connect an Apple Device (iPod, etc.) to the USB terminal. D
If the Apple device is recognized, it is OK.
If "No Data" on the LCD disappears, the device is recognized.
If possible, with the device connected, play a track to check the audio signal for confirmation.
2. Select the iPod function then connect an Apple Device (iPod, etc.) to the USB terminal.
If charging of the Apple device starts, it is OK.
If charging does not start, refer to the diagnosis flowchart for a case in which the USB terminal cannot be recognized on
"5.1 TROUBLESHOOTING".
1. Select the iPod function then put an Apple device (iPod, etc.) in the Dock.
If the Apple device is recognized, it is OK.
If "No Data" on the LCD disappears, the device is recognized.
If possible, with the device connected, play a track to check the audio signal for confirmation.
2. Select the USB function then put an Apple device (iPod, etc.) in the Dock.
If charging of the Apple device starts, it is OK.
3. Disconnect the Apple device from the dock then turn the unit off.
Reconnect the Apple device to the Dock. If the CHARGE LED lights and charging starts, it is OK. F
If charging does not start, refer to the diagnosis flowchart for a case in which the Docking Terminal cannot be recognized
on "5.1 TROUBLESHOOTING"..
X-HM81-K 27
5 6 7 8
1 2 3 4
5.5 IC INFORMATION
A
8952HM7100020-IL (UPD78F1166AGF-GAS)(BCO ASSY: IC4)
16-bit Single-chip Microcontrollers
• Pin Function
No. Mark Pin Name I/O Pin Function
1 P60/SCL0 O
2 P61/SDA0 O
3 P62 O
4 P63 XRST_NW O Network module communication reset
5 P31/TI03/TO03/INTP4 USB_DOCK_OVERLOAD I Detect that BridgeCo detected a USB overcurrent. Active: L
B 6 P64/RD USB_DATA_SW O DOCK USB DATA switching output L:USB / H: DOCK
7 P65/WR0 DOCK_RESISTER O ChargeResister control of USB DATA lines of DOCK Active: L
8 P66/WR1 USB_RESISTER O ChargeResister control of USB DATA lines of USB-A Active: L
9 P67/ASTB USB_START I Detect that BridgeCo started USB control. H: Start Active: H
10 P77/EX23/KR7/INTP11 I
11 P76/EX22/KR6/INTP10 DOCK_SEL I USB connection switching request of BridgeCo Active: H
12 P75/EX21/KR5/INTP9 USB_SEL I USB connection switching request of BridgeCo Active: H
13 P74/EX20/KR4/INTP8 HSYNC I HSYNC monitor of LCD communication
14 P73/EX19/KR3 O NC
15 P72/EX18/KR2 XCS_LCD O LCD communication chip select output (Flow control-Subcon request)
16 P71/EX17/KR1 O
C
17 P70/EX16/KR0 O NC
18 P06/WAIT O NC
19 P05/CLKOUT O NC
20 EVSS1 EVSS1 - Ground of port block (except P20-P27, P110, P111, P121-P124, P150-P157)
21 P80/EX0 DOCK_PWR_ON O DOCK BUS POWER ON/OFF control output Active: H
22 P81/EX1 USB_PWR_ON O USB BUS POWER ON/OFF control output Active: H
23 P82/EX2 O NC
24 P83/EX3 O NC
25 P84/EX4 O NC
26 P85/EX5 O NC
D 27 P86/EX6 O NC
28 P87/EX7 O NC
29 P30/INTP3/RTC1HZ VFD_CE O FL CE
30 EVDD1 EVDD1 - Positive power supply of port block (except P20-P27, P110, P111, P121-P124, P150-P157)
31 P50/EX8 O NC
32 P51/EX9 O NC
33 P52/EX10 O NC
34 P53/EX11 O NC
35 P54/EX12 O NC
36 P55/EX13 USB_DATA_EN O Switch enable output of USB DOCK DATA switch Active: L
37 P56/EX14 O NC
E 38 P57/EX15 O NC
39 P17/EX31/TI02/TO02 O NC
40 P16/EX30/TI01/TO01/INTP5 O NC
41 P15/EX29/RTCDIV/RTCCL O NC
42 P14/EX28/RxD3 DEBUG_RX I 232C DEBUG RX
43 P13/EX27/TxD3 DEBUG_TX O 232C DEBUG TX
44 P12/EX26/SO00/TxD0 TX0_DI_NW O Data output of network module communication (Sub->DM860)
45 P11/EX25/SI00/RxD0 RX0_DO_NW I Data input of network module communication (DM860->Sub)
46 P10/EX24/SCK00 CLK_NW O Clock output of network module communication
47 AVREF1 AVREF1 -
48 P110/ANO0 BT_MUTE O BT MUTE Active: L
F
49 P111/ANO1 CS_NW O Chip select output of network module communication
50 AVREF0 AVREF0 -
28 X-HM81-K
1 2 3 4
5 6 7 8
A
• Pin Function
No. Mark Pin Name I/O Pin Function
51 AVSS AVSS -
52 P157/ANI15 O NC
53 P156/ANI14 O NC
54 P155/ANI13 O NC
55 P154/ANI12 O NC
56 P153/ANI11 O NC
57 P152/ANI10 O NC
58 P151/ANI9 O NC
B
59 P150/ANI8 O NC
60 P27/ANI7 SUB_IRQ O SUB → MAIN REQUEST output
61 P26/ANI6 O NC
62 P25/ANI5 XRST_LCD O LCD communication reset
63 P24/ANI4 O NC
64 P23/ANI3 O NC
65 P22/ANI2 O NC
66 P21/ANI1 O NC
67 P20/ANI0 O NC
68 P130 O NC
69 P131/TI06/TO06 O NC C
70 P04/SCK10/SCL10 CSK_MAIN O Communication clock of MAIN ⇔ SUB
71 P03/SI10/RxD1/SDA10 SCDO_MAIN I Communication data of SUB ← MAIN
72 P02/SO10/TxD1 SCDI_MAIN O Communication data of SUB → MAIN
73 P01/TO00 I NC
74 P00/TI00 REM I IR remote control signal input (NC. only WS)
75 P145/TI07/TO07 PWM_LCD O Backlight control (PWM) of LCD communication
76 P144/SO20/TxD2 DI_LCD O Data output of LCD communication
77 P143/SI20/RxD2/SDA20 DO_LCD I Data input of LCD communication
78 P142/SCK20/SCL20 CLK_LCD O Clock output of LCD communication
79 P141/PCLBUZ1/INTP7 O NC
D
80 P140/PCLBUZ0/INTP6 O NC
81 P120/INTP0/EXLVI MAIN_REQ I MAIN REQUEST input
82 P47/INTP2 REQ_NW I Request input of network module communication
83 P46/INTP1/TI05/TO05 O NC
84 P45/SO01 O NC
85 P44/SI01 VFD_DI I FL DATA input
86 P43/SCK01 VFD_CLK I FL CLOCK
87 P42/TI04/TO04 O NC
88 P41/TOOL1 TOOL1 I/O Clock output for debuggers
- Connect a stable capacitance of the regulator output (2.5V) for internal operation.
96 REGC REGC
Connected to VSS via a capacitor (0.47-1μF: a target).
97 VSS VSS - Ground (except P121-P124 and port block)
98 EVSS0 EVSS0 - Ground of port block (except P20-P27, P110, P111, P121-P124, P150-P157) F
99 VDD VDD - Positive power supply (except P121-P124 and port block)
100 EVDD0 EVDD0 - Positive power supply of port block (except P20-P27, P110, P111, P121-P124, P150-P157)
X-HM81-K 29
5 6 7 8
1 2 3 4
A
(BU4052BCF)(CNT2 ASSY: IC704)
High Voltage CMOS Logic ICs <Analog Switch>
• Pin Arrangement • Pin Function
• Block Diagram
• Control Terminal
F Specific IC
GND
30 X-HM81-K
1 2 3 4
5 6 7 8
6. SERVICE MODE
6.1 SERVICE MODE
1. About Service Mode A
When the unit enters Service mode, the dedicated Service menu is started. In Service mode, the Service menu is open.
You can perform the following tasks on the Service menu:
· Confirmation of the versions of Bco CPU/Main microcomputer/CD IF microcomputer/CD DSP microcomputer
/Submicrocomputer
· Confirmation of the model information (whether the model name recognized by the software is XC-HM71 or XC-HM81)
· Confirmation of the region information (The region recognized by the software will be displayed.)
· Confirmation of the network information
· Updating the Bco CPU or submicrocomputer via USB
· Resetting to factory default
In Service mode, the protection circuits operate in the same manner as in normal operation. B
Note: If you enter Service mode with the CD/TUNER function selected, you cannot use cursor operations.
C
3. How to Quit Service Mode
You can quit Service mode in one of the following ways: (1) switching the function, (2) turning the unit off,
or (3) pressing the k button while the top-layer screen of the Service menu is displayed.
4. Service Menu
For menu operation, use the cursor (i/j/k/l) and ENTER buttons on the remote control unit supplied with this unit.
To register a selection, use the ENTER button. To return to the previous layer, use the k button.
You can perform cursor operation using the buttons on the unit. The top layer of the Service menu is as shown below.
System Information
BcoCPU Ver.: 1.000 Bco (CR870, module on BCO Assy) Version
X-HM81-K 31
5 6 7 8
1 2 3 4
System Information
Region recognized by the software
Region: EU JPN / EU / CAN / CHN
MAC: 74:5e:1c:06:ab:2d MAC Address: The higher-order values "74:5e:1c" are fixed.
Reset?
[SETUP] Reset After resetting to factory default, the unit will shut itself off.
[RETURN] Cancel To quit this mode and return to the Service menu
Note:
If any of the Music Server, Internet Radio, or Favorites functions is selected before this unit is started in Protect Check mode,
the selected function screen will be displayed until network connection is established (it may take up to dozens of seconds),
then the Protect Check Mode screen will be displayed.
Example: Startup → Pioneer Logo → Music Server screen → Network established → Protection Check screen
32 X-HM81-K
1 2 3 4
5 6 7 8
Outline A
Basic Operation
Explanation Key Sequence LCD Display
To enter Protect Check mode, Unit "g (STOP)"
simultaneously press the "g (STOP)" +
and "STANDBY/ON" buttons Unit "STANDBY/ON"
during Cold Standby.
Unit "np"
Unit "np"
Unit "np"
E
Unit "np"
Unit "np"
X-HM81-K 33
5 6 7 8
1 2 3 4
Unit "np"
B
Unit "np"
Unit "np"
After the counts of detected protection
activations for all protection circuits
are displayed, the menu for resetting
the counters will be displayed.
Unit
"np"
Unit
The counters will be reset when the "f (Play/Pause)"
"f (Play/Pause)" button on the
unit is pressed.
D
Auto
E
Unit "STANDBY/ON"
To turn the unit off, press the
"STANDBY/ON" butonn during
Protect Check mode.
Remarks
During Protect Check mode, response to keys other than those described below is disabled.
F Unit "np" button
Unit "f (Play/Pause)" button
Unit "STANDBY/ON" button
34 X-HM81-K
1 2 3 4
5 6 7 8
A
LCD checking is possible in Test mode for use on the production line.
To enter Test mode, select the NETWORK function, then press the ESC then FRM/TIM keys.
TEST MODE will be displayed. (Although TEST MODE is displayed even if the CD or Tuner function
is selected, LCD checking is not possible with those functions selected.)
[Screens to be displayed]
X-HM81-K 35
5 6 7 8
1 2 3 4
A
This unit can display all the characters that are indicated in the white cells in the table below properly but cannot display the
characters in gray cells properly and will indicate such characters as "#." Those are the characters shown below in the RDS
standard:
0x5E
0x60
0x7E
36 X-HM81-K
1 2 3 4
5 6 7 8
7. DISASSEMBLY
Note: A
(1) Do NOT look directly into the pickup lens. The laser beam may cause eye injury.
(2) Even if the unit shown in the photos and illustrations in this manual may differ from your product, the
procedures described here are common.
(3) For performing the diagnosis shown below, the following jigs for service is required:
• BtoB extension jig cable (GGD1770) • 3P Extension jig cable (GGD1773)
• BtoB extension jig cable (GGD1810) • 4P Extension jig cable (GGD1809)
• BtoB extension jig cable (GGD1811) • Extension jig FFC (GGD1774)
• BtoB extension jig cable (GGD1812) • FPC Extension jig (GGD1813)
1 1 1 1
1 1
C
1 1
• Rear view
X-HM81-K 37
5 6 7 8
1 2 3 4
A • DOCKING Assy
(1) Disconnect the one connector.
(CP4)
1
CP4 Cabinet
(2) Remove the shield plate-iPod by removing the Shield plate-iPod DOCKING Assy
two screws.
(B020030081B10-IL)
(3) Remove the DOCKING Assy by unhooking the
two hooks. 2 2 3 3
FPC2
4
5 5
38 X-HM81-K
1 2 3 4
5 6 7 8
A
(7) Disconnect the two connectors. F_AUX Assy F_USB Assy KEY Assy
(CP500, 602) CP602
7
7
CP500
FRONT Assy
X-HM81-K 39
5 6 7 8
1 2 3 4
• CNT3 Assy
(1) Disconnect the four BtoB connectors.
(CP18, 19, 30, 31) 1
(2) Remove the CNT3 Assy. 1 1
CP19
B
CP31 CP30
CNT3 Assy
2
CP18
C • CD Assy
(3) Disconnect the two BtoB connectors.
(PN1701, 1702) CD Assy
(4) Remove the CD Assy. 4
3 3
PN1702
PN1701
Note:
E After working, connect the flexible cable,
then remove the soldered joint (open). 5
(6) Disconnect the one flexible cable.
(PN1602) PN1602
6
MECHA
40 X-HM81-K
1 2 3 4
5 6 7 8
• MECHA A
7 7 B
8
MECHA
• MAIN Assy
1
(1) Remove the one screw.
(B020230083B10-IL) D
2
CP605
CNT1 Assy
F
X-HM81-K 41
5 6 7 8
1 2 3 4
A • Diagnosis
(1) Connect the extension jig FFC to MECHA.
GGD1774: MECHA ↔ CD (PN1602)
(2) Reassemble the front panel section.
(3) Connect the each jig cables.
GGD1770: CD (PN1705) ↔ POWER (CP310)
GGD1773: CNT2 (CN511) ↔ MAIN (CP512)
GGD1809: FRONT (CN515) ↔ CNT3 (CP607)
GGD1810: CNT2 (CP505, 506) ↔ CNT3 (CP30, 31) 3 Extension jig + FFC
GGD1811: CNT1 (CP712) ↔ MAIN (CP605) (GGD1813)
GGD1812: CD (PN1702) ↔ MAIN (CP604)
B
GGD1813: FRONT (FPC515) ↔ CNT3 (FPC2)
(4) Insert the any insulation sheet.
1 Extension jig FFC
(GGD1774)
3 2
Front panel section CD Assy
Extension jig cable
(GGD1770) PN1602
3 Extension jig cable
(GGD1812)
4 PN1705 PN1702
3 Extension jig cable
Insulation sheet (GGD1811)
CP310
3 Extension jig cable
C (GGD1809)
Cut it
CP506 CP505 FPC2 CP607 3 Extension jig cable
CNT2 Assy CN511 (GGD1810)
CP604 CP30
POWER Assy
CP712
CNT3 Assy
CP605
CP31
3 Extension jig cable
(GGD1773)
CP512
MAIN Assy
42 X-HM81-K
1 2 3 4
5 6 7 8
CP11 CP12
5
C
• Diagnosis
(1) Connect the extension jig FFC to MECHA.
GGD1774: MECHA ↔ CD (PN1602)
(2) Connect the each jig cables.
GGD1770: CD (PN1705) ↔ POWER (CP310)
GGD1773: CNT2 (CN511) ↔ MAIN (CP512) Make sure correctly to conect this
GGD1810: CNT2 (CP505, 506) ↔ CNT3 (CP30, 31) cord to BCO Assy as this cord can
GGD1812: CD (PN1702) ↔ MAIN (CP604) be conected to opposite side. D
(3) Insert the any insulation sheet. (It may cause to break circuit in
case of wrong connection. )
BCO Assy
POWER Assy
CNT2 Assy
CP505
F
2 Extension jig cable
(GGD1810) 2 Extension jig cable
(GGD1773)
X-HM81-K 43
5 6 7 8
1 2 3 4
POWER Assy 5
D
• How to Reassemble the POWER Assy
Place the POWER Assy so that the rear side of the POWER Assy comes in contact with that of the chassis,
then secure the four fastening screws of the transformer.
Rear side
POWER Assy
Back chassis Chassis
Transformer
Bring the POWER Assy into contact
with the bend of the chassis.
Rationale:
F If the POWER Assy is not assembled as described above, it will be attached nearer to the front than as designed,
with the result that the cabinet and the rear panel may be separated by a gap or that the front panel may be inclined forward.
44 X-HM81-K
1 2 3 4
5 6 7 8
[Purpose]
Refer to this section when updating the firmware of each microcomputer is required by the service information, etc.
[Necessary Tools]
• PC with a serial port
• Updating program: FlashSta.exe
• RS-232C straight cable (9pin female ↔ 9pin male)
• RS-232C update jig: GGF1642
• Firmware file: ".mot" file
B
[Connections]
Remove the cabinet (bonnet) so that the MAIN Assy becomes accessible.
Connect as shown in the figure below.
For the contact side of the FFC, see the photo below.
10P
PC
RS-232C
Straight cable Contact side
MAIN Assy (side A)
C
UPDATE jig
GGF1642
10P
Front side
D
[Procedures]
1. Unplug the Power cord. 3. Press the OK button.
Connect the FFC cable. ( MAIN microcomputer )
Start up application FlashSta on the PC.
X-HM81-K 45
5 6 7 8
1 2 3 4
4. Select the update file and enter ID. 6. Update Finished MAIN microcomputer.
2 Enter ID.
Enter "ff" in all field.
3 Press OK button to
go to next step.
1 Selection of upgrade file
B
1 Select the update file
Select "XM** Main V0xx.mot" file Press the OK button. 7. Turn the unit off. (STANDBY mode)
to update the MCU. Disconnect the Power cord.
Disconnect the FFC cable.
2 Enter ID.
D
1 Set speed of update.
Set Baud rate to 38400.
(Default Baud rate is 9600)
Press OK button.
46 X-HM81-K
1 2 3 4
5 6 7 8
A
Updating of the Subcom, BCO firmware
[Procedure]
1 Save the update files for Subcom (HM71_81_Sub_***.bcd) and for BCO (HMx2013APP****.bcd) in the root folder of
the USB memory.
* Do not change the file name from a file name when it was released.
2 Plug the power cord into the receptacle and turn on the power.
3 Connect the USB memory in which the update file has been stored to the Product.
4 Press “ESC” → “+10” buttons from service remote control unit (GGF1381) and enter into the Service Mode.
5 Select “Subcom Update Via USB” or “BcoCPU Update Via USB” on the Menu Screen.
6 Press on the “ENTER” button on the Update Screen, and the update starts.
B
7 When update is completed, become the Complete display.
(After the BCO update end, restart automatically. After the Subcom update end, it is necessary to pull out power
cord after display in "Completed!".)
8 Pull out power cord, and put it, and do it, and restart once.
Confirm that Subcom, BCO are revised by "System Information" of "6.1 SERVICE MODE" menu.
Note: Do not plug off the power cord during the update processing.
[ENTER]
[RETURN]
Completed!
E
X-HM81-K 47
5 6 7 8
1 2 3 4
A
BCO update screen
Explanation Key operation Display screen Time
If you select ENTER on this screen, [ENTER] The following icons
updating will start. [RETURN] will be displayed,
To return to the previous screen, Updating in progress, according to the
select RETURN. don’t unplug! actual status:
Muting icon
Sleep icon
[ENTER] LAN icon
[RETURN]
B
48 X-HM81-K
1 2 3 4
5 6 7 8
X-HM81-K 49
5 6 7 8
1 2 3 4
A
Updating of the CD I/F, CD DSP Microcomputers firmware
For updating firmware for the CD I/F and CD DSP microcomputers, create separate discs for updating each microcomputer
then play the disc on the unit.
How to Update
1. Write a ***.UPG file onto a CD-R/RW to create the disc for updating.
Examples of file names (File names vary, depending on the version of firmware.)
For the CD I/F microcomputer: HM71_81CD_IFM_V1_00_110713.UPG
For the CD DSP microcomputer: HM71_81CD_DSP_V102_(20110720_VT).UPG
B File writing can be performed, using the writing function of Windows XP.
Note: Create separate discs for updating the CD I/F and CD DSP microcomputers.
If two files for updating these microcomputers are written on one disc, a problem may occur.
NEVER write files other than a .UPG file onto the CD-R/RW for updating.
50 X-HM81-K
1 2 3 4
Setting Name Initial Setting Setting Range NetStandby Cold FactoryReset Storage Place
SETUP Dimmer LEVEL3 LEVEL3 / LEVEL2 / LEVEL1 Memorized Memorized Clear Maincom
system Europe 6h
AutoPowerDown Off / 2h / 4h / 6h Memorized Memorized Clear Maincom
Other countries Off
Japan Japan English,Japanese
Language China China Chinese Memorized Memorized Clear Maincom
5
5
Other countries English English, French, German, Dutch, Italian, Spanish, Russian
SOUND SOUND FLAT FLAT, GAME, CLASSIC, POPS, VOCAL, JAZ Memorized Memorized Clear Maincom
system P.BASS Off On / Off Memorized Memorized Clear Maincom
BASS 0 -5 to +5 Memorized Memorized Clear Maincom
HM71 +1
TREBLE -5 to +5 Memorized Memorized Clear Maincom
HM81 0
Volume 0 0 to 50 Memorized Memorized Clear Maincom
SYSTEM FUNCTION iPod All functions Memorized Memorized Clear Maincom
8.2 INITIAL SETTINGS
6
PresetName Null 8 characters (ASCII) Memorized Memorized Clear Maincom
Europe 522 522-1602 (9kStep)
Japan 522 522-1620 (9kStep)
AM Frequency Memorized Memorized Clear Maincom
Canada 530 530-1710 (10kStep)
China 522 522-1620 (9kStep)
Europe 87.5 87.5-108.00 (50kStep)
Japan 76.0 76.0-90.00 (100kStep)
FM Frequency Memorized Memorized Clear Maincom
Canada 87.5 87.5-108.00 (100kStep)
X-HM81-K
China 87.5 87.5-108.00 (50kStep)
NETWORK Network Type Auto Wired / Wireless / Auto Memorized Memorized Clear DM870
SSID (Null) 32 characters Memorized Memorized Clear DM870
None / WEP / WPAPSK TKIP / WPAPSK AES
Security None Memorized Memorized Clear DM870
WPA2PSK TKIP / WPA2PSK AES
7
7
WPA Password / WEP Key (Null) 100 characters Memorized Memorized Clear DM870
DHCP On On / Off Memorized Memorized Clear DM870
IP 0.0.0.0 0.0.0.0 to 255.255.255.255 Memorized Memorized Clear DM870
SubNetmask 255.0.0.0 0.0.0.0 to 255.255.255.255 Memorized Memorized Clear DM870
Gateway 0.0.0.0 0.0.0.0 to 255.255.255.255 Memorized Memorized Clear DM870
DNS1 0.0.0.0 0.0.0.0 to 255.255.255.255 Memorized Memorized Clear DM870
DNS2 0.0.0.0 0.0.0.0 to 255.255.255.255 Memorized Memorized Clear DM870
Proxy setting Don't Use Don't Use/Use Memorized Memorized Clear DM870
Proxy Server (Null) 128 characters Memorized Memorized Clear DM870
Proxy Port (Null) 0 to 65535 Memorized Memorized Clear DM870
Friendly Name *1 63 characters Memorized Memorized Clear DM870
Parental Lock Off On / Off Memorized Memorized Clear Maincom
Parental Lock Password 0000 0000 to 9999 Memorized Memorized Clear DM870
8
8
Favorite 0 broadcast station 64 broadcast station Memorized Memorized Clear DM870
Internet Radio Last Play (Null) 1 broadcast station Memorized Memorized Clear DM870
BT Air Jam Air Jam Off Air Jam On / Air Jam Off Memorized Memorized Clear DM870
PIN CODE 0000 0000 / 1234 / 8888 Memorized Memorized Clear DM870
If the AC power cable is unplugged before the settings that have been changed are registered, registration of the changed settings will not be guaranteed.
51
*1 The initial setting is the unit's model name; i.e., XC-HM81 if the unit is a high-end model, or XC-HM71 if the unit is a low-end model.
F
E
B
A
D
C
1 2 3 4
- For the applying amount of lubricants or glue, follow the instructions in this manual.
or or SYXE8
only
B
Except • Speaker • Speaker
CXE
S-HM81GB (for X-HM81/SYXE8), S-HM71 (for X-HM71)
S-HM81SA (for X-HM71-S/AXQ5)
Speaker
S-HM71
(for X-HM71)
Front
Polybag packing style
Polybag packing style Tape
(10 x 100)
Tape (clear) Front (clear)
SET
F SET
Top (side) Bottom
Power cord
52 X-HM81-K
1 2 3 4
5 6 7 8
6 Operating Instructions See Contrast table (2) 16 Non Skid Pad See Contrast table (2)
7 Operating Instructions See Contrast table (2) 17 Snow Cushion See Contrast table (2)
8 Quick Start Guide See Contrast table (2) 18 Soft Sheet See Contrast table (2)
NSP 9 Warranty Card See Contrast table (2) 19 Soft Sheet See Contrast table (2)
10 Box, Gift See Contrast table (2) 20 Speaker Wires See Contrast table (2)
B
21 Snow Cushion See Contrast table (2)
22 Bag Poly See Contrast table (2)
22 Bag Poly Not used Not used Not used Not used
18 Soft Sheet Not used Not used Not used Not used
18 Bag Poly Not used Not used Not used 8952SHM810039-IL
19 Soft Sheet Not used Not used Not used Not used
20 Speaker Wires 8952SHM700042-IL 8952SHM700042-IL 8952SHM700042-IL Not used
F
21 Snow Cushion 8952SHM700045-IL 8952SHM700045-IL 8952SHM700045-IL Not used
X-HM81-K 53
5 6 7 8
1 2 3 4
C
B
C
Bracket-mecha guide
Bracket-mecha guide
M
E
Shield plate-iPod
Cushio LCD
K
D
Shield plate-AUX
Cushio LCD
D
I
J
Shield plate-USB
L
Bottom chass
E X-HM81,
XC-HM81
only
54 X-HM81-K
1 2 3 4
5 6 7 8
Except
AXQ5 model B
A H
G
D
BRIDGE-CO Module
C
D
E
F E
X-HM81,
XC-HM81
only C
X-HM81,
guide
XC-HM81
only
Bracket side C
Support
Bracket side
Main chassis
A
A
C D
Support
Support
Support
Bottom chassis
X-HM81, N E
XC-HM81
only
X-HM81,
XC-HM81
only
NON-CONTACT
CONTACT SIDE
F
SIDE
X-HM81-K 55
5 6 7 8
1 2 3 4
B 56 Screw B020030171B10-IL
11 DOCKING Assy 7028072544010-IL
12 BCO Assy See Contrast table (2) 57 Screw BBT30P100FTB
13 CNT2 Assy See Contrast table (2) 58 Screw B028940101B11-IL
NSP 14 CNT3 Assy ••••• 59 Screw See Contrast table (2)
15 CD Assy 7028072301010-IL 60 Screw See Contrast table (2)
56 X-HM81-K
1 2 3 4
5 6 7 8
C
59 Screw B020230083B10-IL BBZ30P080FNI B020230083B10-IL BBZ30P080FNI
60 Screw B020030083F10-IL B020030084F10-IL B020030083F10-IL B020030084F10-IL
X-HM81-K 57
5 6 7 8
1 2 3 4
Holder catch
SYXE8 SYXE8
only only
Holder catch
Holder catch
Holder catch
Badge Pioneer
58 X-HM81-K
1 2 3 4
5 6 7 8
Holder catch
Holder catch
C
Holder catch
Holder catch
Badge Pioneer
D
SPAEKER SECTION (for X-HM71) SECTION PARTS LIST
Mark No. Description Part No.
1 Unit Woofer 8952SHM710014-IL
2 Tweeter 8952SHM710009-IL
3 Network Assy 8952SHM710012-IL
4 Frame Net Assy 8952SHM700019-IL
5 Deco Unit 8952SHM710005-IL
X-HM81-K 59
5 6 7 8
1 2 3 4
D
CP604
PN1607
2.5mm * 2Pin
(CD) (CD)
D 1/3
E
N CP310
A
60 X-HM81-K
1 2 3 4
5 6 7 8
A
A CD ASSY (7028072301010)
(CD)
: Audio Signal Route (CD Lch)
1 B
MECHA (PICKUP)
C
(SPINDLE/SLED)
(CD)
MECHA
MECHA
(TRAY)
PN1607 (CD)
2.5mm * 2Pin
(CD)
(CD)
2.5mm * 6Pin
A
X-HM81-K 61
5 6 7 8
1 2 3 4
A B TUNER ASSY
(7028072534030-IL: X-HM81, XC-HM81)
(7028072534060-IL: X-HM71/SYXE8)
(7028072534040-IL: X-HM71/CXE, AXQ5)
B (LINE) C406
(LINE)
330P-J
(SW) (SW)
C408
330P-J
JK402 (SW) R413 R414 (SW)
470 470
100K
(LINE)
R418 R417
10K 10K
(LINE)
R416
Q401 Q400
KTC2875B KTC2875B
C412
100P-J
(TU) (TU) (TU)
10N
C413
TUNER_PACK_OPTION
RDS
KST-MW104MV1-S78A
(TU)
TUNER_OPTION
1V2
3V3
E NC
VCC_GND
NC
NC
NC
AUD_R
AUD_L
AGND
DAB_RX//M_TX
DAB_TX//M_RX
RESET
SPDIF
B
62 X-HM81-K
1 2 3 4
5 6 7 8
(SW) (SW)
(LINE) (LINE)
(TU) (TU)
G CP402
C BT ASSY (7028072537010-IL)
R1017 R1018
10K 10K
D
Q1003 Q1002
CP6
KTC2875B KTC2875B
E 1/2
E
B C
X-HM81-K 63
5 6 7 8
1 2 3 4
CP512
FPC600
G CN511
R661
10K
(CD)
: Audio Signal Route (CD Lch)
(TU)
: Audio Signal Route (TUNER L ch)
10K
10K
(LINE)
R670
R673
: Audio Signal Route (LINE IN L ch)
B (FA)
22
: Audio Signal Route (Front AUDIO IN L ch)
10K
10K
(USB)
R615
: Audio Signal Route (USB L ch)
22
22
22
22
22
22
22
R606 10K
22
R680
R845 NM
(HP)
R849
R754
6-4
R669
: Audio Signal Route (Phones L ch)
R846
R847
R844
R843
R658
R861
R848
22
(SW)
: Audio Signal Route (SubWoofer ch)
6-3 C607
100N-K
10K
10K
6-2
R622
R623
CPU_GND
SW_MUTE
HP_MUTE
SUB_PDN
HP_DET
VOL_DN
SUB_ON
CPU_3V3
IPOD_C_LED
SUB_IRQ
VOL_UP
SET_OPT
POWER_ON_LED
NC
NC
AUDIO_SEL
NC
DAC_RST
R624 BLM121
NC
VFD_DATA
R627 BLM121
VFD_CLK
R628 BLM121
VFD_CE
R632 BLM121
VFD_RST
NC
NC
78.AMP_PROTECT_DET
79.SPK_RLY
80.AMP_PD
8-1 8-2
53.NC
6-1
*
52.CD_MAIN_
9-3 NC_ 51.CD_RST
C601 4N7-K
R671
R672
NC
CP602 R869 22
KEY2
R870 22
KEY1
IC601
CN510
R626 220/10
C602 REGION_OPT
C800 100N
CW24C16 R649 22
OVER_TEMPERATURE_PROTECT_1
R663 22
A0 OVER_TEMPERATURE_PROTECT_2
3-1 3-2
C799 OPEN
4 3 2 1
5 6 7 8
VCC
C R625
10K
C798 OPEN
A1 WP TIMER_LED
10K R629
99. CPU_3V3
C776 OPEN
A2 SCLK EEPROM_CLK 100.MUTE_B+_S/W
22
C662 OPEN
GND SDA
R633
CPU_GND
EEPROM_DATA
1.M3V3_SW
2.PWM_DETECT 2-1 2-2
I
SUB_CLK_OUT
C603
POWER_PROT
22
DC_PROTECT
C604 C609
SUB_CLK_IN
100P-J
9-1 9-2 100N-K VREF
CNVSS_UP
100P-J
CPU_GND
CPU_GND
PWM_350
PWM_400
CPU_3V3
C608
TU_INT
RESET
X_OUT
100N-K
RMC
100
NMI
XIN
BD600
NC
NC
NC
PD
0
22
(USB) R677 22
(HP)
R840
(FA)
R609 22
22
100N-K
22
(CD)
C600
100K
D600
R696
10N-K
KDS4148U C615
R616
R656
C 2/3 (TU) R608 10K R697
open
XTAL601 32.768K
R602 10K
(LINE)
VOL_PART
ZTTWS16M
20P-J
10K
XTAL600
R660
10K
KDS4148U
20P-J
C611
R666
(SW) Q602
C610
D601
KTA1504S R679
1K
R681
390
D Q603
KRC102S
C 3/3
AMP_PART
Q609
KDS4148U
D602
D603
KTA1504S KDS4148U
R682
E 1K
R683
390
10k
ZD600 R686 R684 R829 R685
0 1K 220K
Q607 1K
KRC102S
R687
D604 10K
KDS4148U
CP712
Q630 C612
R688
4K7
KRC102S
C739
C740
C754
C759
C760
C761
Q608
-
4.7/50 KTC3875S
C614
R690
47K
KDS4148U
R689 R828
4K7
10N-K
C613 OPEN
10N-K
F
D605
F
C736
C737
C738
-
D 1/3 CP605
64 X-HM81-K
1 2 3 4
5 6 7 8
CP509
DAC_RST
SUB_PDN
SUB_IRQ
SUB_ON B
10K
10K
R621 10K
R603 10K
22
22
22
22
22
22
22
22
22
22
R680
R845 NM
R605 10K
R849
R754
R669
R667
R846
R847
R844
R843
R611
R610
R861
R848
22
C607
7-2 7-1
10K R607
100N-K
CP18
CPU_GND
5-1 5-4
SUB_PDN
MAIN_IRQ
SUB_ON
CPU_3V3
IPOD_C_LED
IPOD_DETECT
SUB_IRQ
SUB_RESET
POWER_ON_LED
NC
NC
VIDEO_MUTE
AUDIO_SEL
DAC_RST
NC
NC
NC
NC
R617 22
TU_RESET
H
TU_SEN
R665 22
IPOD_CHARGE_LED
POWER_ON_LED
53.NC TU_SLK
R619 22
52.CD_MAIN_BUSY TU_SDIO
51.CD_RST
5-2 STBY_RLY
NC
R620 22
EPM_UP
NC
NC
3-1 3-2
NC
Q601
KRA102S
R659 22
CSCK_MAIN
R837 22
C
34. CTS SCDI_MAIN
33. CLK R842 22 R653
2-1 2-2 32. DAB_UP_RXD
31. DAB_UP_TXD
SCDO_MAIN
R654 22
10K
UP GRADE
JIG
SUB_CLK_OUT
R664 22
MAIN_MUTE
VOL_LATCH
VOL_DATA
CPU_GND
PWM_350
PWM_400
PWM_300
R838 -
VOL_CLK
CPU_3V3
AMP_ON
TU_INT
CD_RX
RESET
X_OUT
CD_TX
NMI
XIN
CP606
NC
PD
R839
3k3
3k3
-
22
22
22
R740 47K
-
22
(SW)
R750
R708
R709
4-2
R612
R840
R613
R614
R780 3k3
R668 3k3
100N-K
C600
100K
(TU)
R697
pen
CP19
10K
10K
10K
10K
OPEN
OPEN
ZTTWS16M
D625
D626
XTAL600
10K
4-1 (USB)
R600
R601
10K
10K
R675
R676
R604
10K
R789
R801
20P-J
C611
R666
H
R732 10K
(LINE)
VOL_IC_PART
D
C 2/3
E
PN1702
(CD)
A
D 1/3
X-HM81-K 65
5 6 7 8
1 2 3 4
(FL)
(FA) (FA)
(USB) (USB)
(TU) (TU)
(CD) (CD)
(FL)
B (LINE) (LINE)
(FL)
(FL)
(FA)
MICOM
(FA)
MICOM
_SHEET
C654 OPEN
FAUX_R IC604:A
OPEN
2
R720 C785 R721
OPEN 1
OPEN OPEN
3 4
C663 OPEN
- C664
56K R731
IC605:A
BA4560F
HP_R
R544 R546 C668
100/16 2
10 390
C745
E R733 C712
82P
1 4.7/50
100
4 3
OPEN
KTC2875B
R550 R552
C743
Q500
R548
OPEN
R741 BD121
OPEN
R560 R562
C744
7 C713
82P
100 4.7/50
10 R568 C683
100/16 IC605:B
BA4560F
6
HP_L
56K R746
- C682
Q600
KRA102S
D 2/3
66 X-HM81-K
1 2 3 4
5 6 7 8
IC602:A
AZ4580 Copper wire Bonding
B
C616 OPEN
AMP_L OPEN
R693 2K
R830 AMP_SHEET
2 (FL) (FL)
OPEN
C741
R698 -
D 3/3
(FL)
OPEN
C770
R704 C670
R703 C673
OPEN
47N-Z Q610
C775
R705 2K 47/16
100K 100K R706 - R707
R735 - -
100 Q615
5 8 -
OPEN
R812
C742
C671 100 7
4.7/50 R710 R711
6 820-F 820-F
R823
OPEN R712 -
R714 2K
(CD)
: Audio Signal Route (CD Lch)
(TU)
: Audio Signal Route (TUNER L ch)
(LINE)
: Audio Signal Route (LINE IN L ch)
(FA)
: Audio Signal Route (Front AUDIO IN L ch)
(USB)
: Audio Signal Route (USB L ch) D
(FL)
: Audio Signal Route (Front L ch)
(HP)
: Audio Signal Route (Phones L ch)
(SW)
: Audio Signal Route (SubWoofer ch)
(SW) (SW)
C678
OPEN IC606:A
AZ4580 Copper wire Bonding
C667
IC606:B R736 10K 47N-K
C784
C675
4.7/50
R734
3K9
AZ4580 Copper wire Bonding
3 4 10/16 E
R862
5K1
6 1
(SW) 7 2 (SW)
OPEN
C676
5 8
BD602 10K R841
C783 C781
(FL)
BD121T 68N
47N-K
C680
(SW) 4.7/50
R745
3K9
D 2/3
X-HM81-K 67
5 6 7 8
1 2 3 4
D 1/3
PWM_FREQ
SELF 422Khz
MODE2 Q619,Q629 ON(MODE1) 322Khz
Q615,Q627 ON(MODE2) 300Khz
D 1/3
MODE1
SELF
18 10 11
IR_KOREA
12
Q620
OPEN (FL)
(FL)
C
(FL)
20 19
OPEN
Q624
21
23 15 16
17 13 14
22
18
D 2/3 10 11
D (FL) (FL) 20 12
21 19 15 16
23 17 13 14
D 1/3 22
D 3/3
68 X-HM81-K
1 2 3 4
5 6 7 8
(FL)
3K3(2)
: Audio Signal Route (Front L ch)
R747
R872 R749 B
47K Q612
10-2012 KTA1504S
Q613
KTD1898
422Khz
1) 322Khz
2) 300Khz
D 2/3
1K2(1)
1K2(1)
R833
R832
EMI
(FL)
15 16
2011.07.11
C825 NC
C824 470N
EMI
C823 470N
C822 470N
C821 NC
C815 470N
(FL) C814 470N
C813 470N
22N(EB)-100V
10N(EB)-100V
10N(EB)-100V
22N(EB)-100V
C705
C706
C707
C708
RLY600
G5PA-28-MC
OPEN
OPEN
L602
22UH
C801
C802
1.619V
15 16
EMI
1SS355
100K
C730
R819 10N
47K(1/4)
D619 R818
C787 1SS355 27K
68N
R820 R859
10(1/4) 10(1/4)
KTC3198
D620
Q639
KDS4148U C731
100N-K R824
100K
E
R826
KTA1268
47K(1/4)
Q635
Q642
KTC3198
R827
10K
D 3/3
X-HM81-K 69
5 6 7 8
1 2 3 4
E 2/2
A
CP12
G
E 2/2
E 2/2
E 2/2
GND
GND
GND R177
IOVCC(+3.3V) -
IOVCC(+3.3V)
L21 BD121
LED-CTL(SPSW)
C LED-A+ C113 C110
220P 220P
L20 BD121
SDA
VSYNC
HSYNC
DOTCLK
DE
CLK
CSX
CP11
R2
DB17/R5 -
DB16/R4
DB15/R3
DB14/R2
DB13/R1
G
R87 0
DB12/R0
DB11/G5
DB10/G4
R88
DB9/G3 1M
DB8/G2 XTAL1
20M
DB7/G1
DB6/G0
R89
DB5/B5 0
D DB4/B4
DB3/B3 C100 C101
DB2/B2 12P-J 12P-J
DB1/B1
DB0/B0
RESX
R31 0
C96
100P
E R33 0
R44
BD121T
E 2/2
E 1/2
70 X-HM81-K
1 2 3 4
5 6 7 8
R96 0
R95 0
4K7
4K7
1K
R130
R131
R237
R258
0
E 2/2
R259 0
47K
POWER NOISE
47K
47K
R92
R86 10K
47K
R91
R90
R106
100
47K
47K
47K
47K
47K
47K
47K
47K
47K
47K
47K
47K
47K
47K
47K
47K
47K
47K
47K
100
100
100
100
47K
33
0
0
47K
100
33
-
R83
R122
R260
R216
R228
R229
R123
R215
R214
R213
R195
R105
R196
R85
R179
R99
R193
R192
R191
R190
R189
R188
R187
R186
R185
R184
R183
R182
R181
R180
R84
R108
100
0
R235
R232
3 C110
220P
C107 100N
C
P R107 100
R197 0 R119 100
R125 47K C108 100N
E 2/2
R126 100 R109 100
R127 100 30-2 33-2 R110 10
R198 47K R111 10
R100 0 30-3 R117 0
R236 R102 0 33-1 R116 0
- 47K
R112
R103 R199 47K R113 47K
100 R200 47K R176 47K
330P
C111
31-1 R104 0
32-3
R175 47K
87 0
32-1 32-2 R174
R173
47K
10
C102 1/50 R172 47K
R171 47K
R88
1M 31-2 47K
30-1 R170
R169 47K
C103 100N R168 47K
R89 10/16
C104
0
D
C114
10K
47K
47K
47K
47K
47K
47K
47K
47K
47K
47K
47K
100
100
101 220P
100
100
10
10
47K
47K
47K
0
100
P-J
10
-
R267
R208
R114
R164
10K
R129
R132
R149
R134
R135
R136
R137
R138
R160
R139
R141
R143
R144
R146
R147
R167
R270
R178
R120
R121
R124
R128
C105 C106
100N 100/6.3
R262 10K
47K
R115
R133 R209
100 R202 R261 47K
100
R279 R278 -
10K 10K
R276
10K
R277
1K
E
R201
330K
C CP1001
E 2/2
E 2/2
E 1/2
X-HM81-K 71
5 6 7 8
1 2 3 4
A
E 2/2 BCO ASSY (7028072551010-IL: X-HM81,XC-HM81)
(7028072551020-IL: X-HM71)
27
IC5
AOZ1212AI L1
10UH
5 6 7 8
4 3 2 1
BD16
VCC_IN
OPEN
31K6-F
BD121T D6
R3
RB081L
R4
BD121T
UDZ3.6V
BD15
Q3 3V3_SET
D1
KRA102S
29
Vout=0.8(1+(R4/R5))
R2
28
Q4 3K3-F R5
KRC102S 10K-F
100N-K-50V
370Khz
AOZ1212
C3
R1
4K7
IC2
PQ012FZ01ZP
1 3
220/6.3
220/6.3
4
4700N-K
4700N-K
100N-K
22/25
100N-K
2 5
C44
C48
C43
C45
C46
C40
C41
C42
0.33/50
IC8
MFI341S2162
CN702
NC 10
C89
NC 6
NC 7
NC 8
NC 9
10N-K 10N-K
27
15 14 13 12 11
5
VCC VSS
nRESET SCL
4
BD17 BD121T
BD18 BD121T IC9
NC SDA
3
AOZ1212AI
MODE1 MODE0
2
R79 NC NC
5 6 7 8
4 3 2 1
NC
19 NC
18 NC
17 NC
1
16 NC
4K7
F
L3
10UH
20
R
4
Q7
KRA102S
RB081L
62K-F
R14 150K-F
8K2-F
D8
5V_SET
29 28 R70 100
3K3-F
100N-K-50V
R13
R12
370Khz
Q8
R16
C20
KRC102S
R11
4K7 L7
L18 BD121T BD121T
L22 BD121T
D R26 10K
R60
10
D2 KDS4148U
R58
10
GND FAULT
1
IN OUT L4 0
2
C50
F_USB
L5 0
IN OUT
3
1000N-Z EN LIM
4
L6 0
R24
R23
IC11
100
-
TPS2557 L8 0
H->EN
R28
24K-F
L9
BD121
R29 C51
22K-F 220/6.3-Z8157
R38
-
R50 R57
R39 - 100
-
S : L -- FRONT USB
S : H -- DOCK USB
(U
DOCKING
E
100N-K
OPEN
100P-J
10N-K
1N-K
R56
10K
BD121T
BD121T
27
BD13
BD14
R140
R142
D9 D3 KDS4148U
C64
C66
C67
C65
RB081L R46
0
IC13
AOZ1212AI
GND FAULT
1
8
DOCKING
IN OUT
L10 0 (UD)
5 6 7 8
4 3 2 1
C60 R49
L14 IN OUT
L11 0 0
3
10UH (UD)
100
R53
L13 0
Q9
29 IC14
R55 (UD) R54
R35
100P-J
OPEN
OPEN
10N-K
5V_SET
1N-K
3K3-F
R36
R41
370Khz
24K-F
Q10
100N-K-50V
KRC102S R40
R148
R37 C61
C68
C70
C71
4K7
R145
C54
C69
28
E 1/2
A
10K
10K
R204
R205
R203
100
R162
100
C97 C98
220/6.3
220/6.3
R152
R153
0
0
B
R154 0 R155 0
R163 10
R165 10 R156 0
R263 0
470K
-
10K
R265
1K
R207
R212
R206
E 1/2
R266
-
IC8
MFI341S2162 C92 R166 0
C91 100P-J
100P-J
C
NC 10
NC 6
NC 7
NC 8
NC 9
K
R78 100
15 14 13 12 11
5
16 NC
R75
4K7 R244 47K R242 47K
20
R76
4K7 R245 47K
R249 47K
R194
R251
47K
47K E 1/2
R250 47K
D
R257 4K7
C85
-
C80 -
M CP4
C81 -
C78 -
C79 -
L17 BD121
JACK1
R157 - 99TA-03188
CP1 R72 0
1
C77
R69 0
43K2-F
D- R222
0 R217 R220 - R68 0
3
D+ 49K9-F 0
110707
(UD) (UD)
R218
L28 R67 75
+5V
4
R161 -
R52 0 C76
RESISTOR R66 0
6
100N-K
OPEN
OPEN
OPEN
OPEN
100P-J
10N-K
1N-K
-
7
0 75
C72
C73
10 9
R140
R142
DAC PART
C64
C66
C67
C65
R264
E 1/2 10K
R234
100
1N/2KV
R158 0
+5V R219
0
(UD) (UD) +5V
C82
R53 0 D- R274
R54 10K
0 D+
L35
OPEN
OPEN
-
100N-K
GND
100P-J
OPEN
OPEN
10N-K
1N-K
R159 0 GND
R223
75K-F R231
C74
C75
0
CP2
10N
10K
R148
C68
C70
C71
R145
C69
R253
R224 100
49K9-F
R227
(UD)
J CP500 : USB Data Signal Route
10K
R226 43K2-F
R275
R230
R225
F
0
49K9-F
E 2/2
X-HM81-K 73
5 6 7 8
1 2 3 4
A
F CNT1 ASSY
B
BD711 BD221T
BD710 BD221T
CP5
BD707 BD221T
BD708 BD221T
BD709 BD221T
E 2/2
BD704
-
C
CP605
D 1/3
F
74 X-HM81-K
1 2 3 4
5 6 7 8
N CP312
F
X-HM81-K 75
5 6 7 8
1 2 3 4
A G CNT2 ASSY
(7028072552010-IL/X-HM81, XC-HM81) H CP31
(7028072552020-IL/X-HM71)
(USB)
(TU)
: Audio Signal Route (TUNER L ch)
(SW)
(USB)
B
(LINE)
: Audio Signal Route (USB L ch)
(TU)
(USB)
(TU)
C
0
BD7
BD6
0
BD10
0
BD11
0
B CP400
(USB)
BD12 Q16
KRC102S
(TU)
0 KRA102S
R283
Q17
1K
BD9 0
R280
1K
BD8 0
BD5 0 R273
(LINE) 10K
Q14
KTC2875B
(SW)
D R272
10K
R282
1K
Q15
KTC2875B
R281
330K
R312
22K
R313 22K
E
BLUE_TOOTH_OPTION
XHM81 ADD
XHM71 OPEN
CP12
G E 1/2 CP8
76 X-HM81-K
1 2 3 4
R280
1K
P8
Q17
KRC102S
SUB_ON
(USB)
SUB_IRQ
5
5
24
26
R284 0
RESX
DB0/B0 R285 100
R286100
DB1/B1
R287100
DB2/B2
R288100
DB3/B3
R289100
DB4/B4
R290100
DB5/B5
R291100
DB6/G0
R292100
DB7/G1
R293100
25
DB8/G2
R294100
DB9/G3
R295100 RESX
DB10/G4
R296100 DB0/B0
DB11/G5
6
6
R297100 DB1/B1
DB12/R0
R298100 DB2/B2
DB13/R1
R299100 DB3/B3
DB14/R2
R300100 DB4/B4
DB15/R3
R301100 DB5/B5
DB16/R4
E 1/2
R302100 DB6/G0
DB17/R5
R303 0 DB7/G1
CSX
R304 0 DB8/G2
SCL
R305 0 DB9/G3
DE
CP7
R306 0 DB10/G4
(GND_SHIELD) DOTCLK
R307 0 DB11/G5
CN511
HSYNC 0 DB12/R0
R308
X-HM81-K
H
D 1/3
DB14/R2
LED-A+ R311 0 DB15/R3
LED-CTL(SPSW) DB16/R4
CP30
IOVCC(+3.3V) DB17/R5
CSX
IOVCC(+3.3V) SCL
7
7
GND DE
CP512
GND CSX
GND DOTCLK
HSYNC
VSYNC
SDA
LED-A+
CP11
LED-CTL
IOVCC(+3.3V)
IOVCC(+3.3V)
GND
GND
SUB_PDN
8
8
G
77
F
E
B
A
D
C
1 2 3 4
K CN515
A H CNT3 ASSY
IOVCC(+3.3V)
IOVCC(+3.3V)
LCDGND
LCDGND
4P_WAFER
CP607
(SW)
: Audio Signal Route (SubWoofer ch)
(LINE)
: Audio Signal Route (LINE IN L ch)
(TU)
: Audio Signal Route (TUNER L ch)
(USB)
: Audio Signal Route (USB L ch)
E
(SW)
(TU)
(LINE)
(USB)
DB10/G4
DB11/G5
DB6/G0
DB7/G1
DB8/G2
DB9/G3
DB12/R0
DB13/R1
DB14/R2
DB1 /R3
SUB_IRQ
DB0/B0
DB1/B1
DB2/B2
DB3/B3
DB4/B4
DB5/B5
SUB_ON
RESX
G CP505 G
H
78 X-HM81-K
1 2 3 4
DB4/B4
DB5/B5
515
DB6/G0
DB7/G1
CP607
DB8/G2
4P_WAFER
DB9/G3
DB10/G4
DB11/G5
DB12/R0
DB13/R1
DB14/R2
DB15/R3
G
DB16/R4
DB17/R5
CSX
SCL
DE LED_A
5
5
LED_B
CSX
LED-CTL
CP506
DOTCLK
LED-A+
HSYNC
SDA
VSYNC
VSYNC
SDA
HSYNC
LED-A+
DOTCLK
LED-CTL
DE
IOVCC(+3.3V)
SCL
IOVCC(+3.3V)
CSX
GND DB17/R5
GND
DB16/R4
SUB_PDN DB15/R3
DB14/R2
DB13/R1
DB12/R0
DB11/G5
DB10/G4
K
DB9/G3
DB8/G2
DB7/G1
DB6/G0
6
6
DB5/B5
DB4/B4
FPC515
DB3/B3
DB2/B2
DB1/B1
DB0/B0
RESX
X-HM81-K
(USB)
(TU)
(LINE)
(SW)
FPC2
7
7
0.5MM 40MMP FPC
CP19
CP18
SUB_ON
SUB_IRQ
SUB_PDN
DAC_RST
POWER_ON_LED
IPOD_CHARGE_LED
D 1/3 CP606
D 1/3 CP509
8
8
H
79
F
E
B
A
D
C
1 2 3 4
A
I F_AUX ASSY
JK502
(7028072535010-IL)
VCI(+3.3V)
(FA) (FA)
DB0/B0
100
DB1/B1
R524
RESX
GND
R526 100
AUDIO IN
SHEILD PLATE_OPEN
470P-J
470P-J
47K
47K
C552
C550
R534
R532
100N-K
D504 KDS4148U
10N
D506 KDS4148U
C537
C539
C545
C563 100N-K
B
JK504 BD500 (HP)
BD502
0
H/P
D508 R572
0
CDS3C05HDMI
D510
KDS4148U
D514
KDS4148U R118
10N-K
27(1/2)
10N-K
C570
100N-K
C565
C567
(FA)
R27
Q18 -
KRC103S
(HP)
PLATE1 (HP)
: Audio Signal Route (Phones L ch)
(FA)
: Audio Signal Route (Front AUDIO IN L ch) D 1/3 CP602
SHEILD PLATE
(UD)
F_USB JACK
R522 -
J F_USB ASSY
C505
C502
10P-K
100P-K
(7028072536010-IL) G
C501 100N-K R5
JK500
R5
C503 100/10 R521
-
USB_VCC_+5V
(UD) C55
USBHO_D-
L501
DLP11SN121SL2L
(UD) C555
USBHO_D+
USB_GND
R523
-
D501 CDS3C05HDMI
E D503 CDS3C05HDMI
C511 1N
10
10
C541
10
-
10
10
10
10
10
10
C517 100N
C519 100N C542
R569
R567
R581
R579
R577
R576
R575
R573
R571
10N
L504 L505
L503 L502 0
0 0 0
D502
CDS3C05HDMI CN515
IOVCC(+3.3V)
IOVCC(+3.3V)
GND
GND
LED-A+
DOTCLK
LED-CTL
DB17/R5
CSX
SDA
LED_A
LED_B
SCL
HSYNC
VSYNC
DE
GND500
4P WIRE
CP500
E 2/2 CP2
I J K
80 X-HM81-K
1 2 3 4
LED_A
LED_B
LED-CTL R581 10
R118
27(1/2)
C537 100N-K
LED-A+
SDA R579 10 C539 -
R577 10
VSYNC
R576 10
Q18
HSYNC C545 10N GND
KRC103S
R575 10
DOTCLK VCI(+3.3V)
R573 10
DE RESX
SCL R571 10
DB0/B0
-
CSX R569 10
R27
DB1/B1
C555
DB17/R5 R567 10
C557
DB2/B2
R541
R542
DB16/R4 R565 10
DB3/B3
DB15/R3 R563 10
DB4/B4
-
R561 10
-
DB14/R2 DB5/B5
OPEN
OPEN
DB13/R1 R559 10
DB6/G0
5
5
H
DB12/R0 R557 10
DB7/G1
DB11/G5 R555 10
DB8/G2
DB10/G4 R553 10
GND_OPTION
DB9/G3
DB9/G3 R551 10
DB10/G4
DB8/G2 R549 10
DB11/G5
FPC2
R547 10
C556
C558
C560
C559
C562
C561
DB5/B5 DB14/R2
DB4/B4 R537 10
DB15/R3
-
-
-
-
-
-
DB3/B3 R535 10
DB16/R4
DB2/B2 R533 10
DB17/R5
DB1/B1 R531 10
KEY_PART
CSX
DB0/B0 R529 10
SCL
RESX R578 10
DE
S506
DOTCLK
HSYNC
10N
S510
C554
VSYNC
SDA
2K
LED-A+
R540
LED-K1
0 LED-K2
6
6
BD501 LED-K3
BD503
0
LED-K4
IOVCC(+3.3V)
GND
C540
100N-K
-
C543
FPC515
K
C574
C572
X-HM81-K
100N-K
100N-K
RMC500
R34FS9A
47
R528
C536
10N-K
7
7
100
R518
C532
47P-J
C538
FRONT ASSY
47/16
VOL_UP
C544 -
GND
C564
820P-K
C546 -
GND502
C548 -
C566
820P-K
(7028072531010-IL)
VOL_DN
C569
C568
L
100N
D517
D518 -
KEY ASSY
R543
1K2
R538
R536
R530
1K5
2K
2K7
8
8
D512 KDS4148
CP508
CN,WAFER2.0MM/2P,AN
-
CN502
D516 KDS4148
10N
C571
S512
S504
S502
S500
S508
K L
(7028072533010-IL)
81
F
E
B
A
D
C
1 2 3 4
M DOCKING ASSY
(7028072544010-IL)
C
BD4
OPEN
BD2 0
BD3 0
D
SHEILD PLATE
M
82 X-HM81-K
1 2 3 4
5 6 7 8
CP1
C
BD102
E 2/2
BD1 0 BD121T
PLATE
M
X-HM81-K 83
5 6 7 8
1 2 3 4
+B
CP710
B
F
-B
DC
DC
DC12V
+12V
+5V
-12V
-5V
D
VCC IN
200mA
PN1705
A
3V9
N
84 X-HM81-K
1 2 3 4
5 6 7 8
N POWER ASSY A
(7028072542030-IL: X-HM81,XC-HM81)
(7028072542030-IL: X-HM71/SYXE8, AXQ5)
(7028072542040-IL: X-HM71/CXE)
CP301
AC
B
AC
DC
AC
DC
D
VCC IN
3V9 VCC_IN
N
X-HM81-K 85
5 6 7 8
1 2 3 4
10.14 WAVEFORMS
A NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
A CD ASSY
PN1602 - pin 11 (B) IC612/IC608 - pin 16 (CSH) IC612/IC608 - pin 11 (LO)
1 V: 100 mV/div. H: 400 nsec/div.
10 V: 20 V/div. H: 1 μsec/div. 15 V: 20 V/div. H: 2 μsec/div.
(CD PLAY)(Coupling: AC)
2-1 6-3
C 6-1
2-2 6-2 IC612/IC608 - pin 14 (HO) IC612/IC608 - pin 9 (DT)
12 V: 20 V/div. H: 1 μsec/div. 17 V: 20 V/div. H: 1 μsec/div.
6-4
IC609 - pin 10 (SUB_CLK_IN)
3-1 V: 2 V/div. H: 5 μsec/div.
IC609 - pin 11 (SUB_CLK_OUT)
3-2 V: 2 V/div. H: 5 μsec/div.
7-1
IC612/IC608 - pin 13 (VS) IC612/IC608 - pin 1 (VAA)
D 7-2 13 V: 20 V/div. H: 1 μsec/div. 18 V: 2 V/div. H: 200 msec/div.
5-1
5-3
5-4
F 9-1
9-2
9-3
86 X-HM81-K
1 2 3 4
5 6 7 8
A
G CNT2 ASSY E BCO ASSY
IC612/IC608 - pin 5 (CSD) IC208 - pin 3 (SDTI) IC5/IC9/IC13 - pin 1 (LX) IC4 - pin 29 (VFD_CE)
20 V: 2 V/div. H: 1 sec/div. 24 V: 2 V/div. H: 10 μsec/div. 27 V: 5 V/div. H: 2 μsec/div. 30-1 V: 2 V/div. H: 500 msec/div.
IC4 - pin 85 (VFD_DI)
30-2 V: 2 V/div. H: 500 msec/div.
IC4 - pin 86 (VFD_CLK)
30-3 V: 2 V/div. H: 500 msec/div.
D
IC4 - pin 44 (TX0_DI_NW)
33-1 V: 2 V/div. H: 500 msec/div.
IC4 - pin 45 (RX0_DO_NW)
33-2 V: 2 V/div. H: 500 msec/div.
X-HM81-K 87
5 6 7 8
1 2 3 4
B
CP310
PN1705
N
PN1603 PN1604
MECHA MECHA
(TRAY) (SPINDLE/SLED)
Q1601 IC1603 Q1602
IC1604 IC1606 IC1605
SIDE B
D
PN1603 PN1604
PN1705
A PN1602
88 X-HM81-K
1 2 3 4
5 6 7 8
A
N1602
MECHA SIDE A
(PICKUP)
CP604
PN1702
D
C
SIDE B
D
PN1702
SIDE A
SIDE B F
P.C.Board Chip Part
N1602 A
X-HM81-K 89
5 6 7 8
1 2 3 4
B TUNER ASSY
D
C BT ASSY
E CP400
G CP402 CP1001
E CP6
IC600
Q1001
B C
90 X-HM81-K
1 2 3 4
5 6 7 8
SIDE B SIDE B
A
IC403
IC400 IC402
B TUNER ASSY
B
C BT ASSY D
CP400 E
CP1001
Q1003
Q1002
B C
X-HM81-K 91
5 6 7 8
1 2 3 4
H CP18
D MAIN ASSY
CP509
B A PN1702
CP604
32
CP605
CP602
F CP712
I CN510
D
92 X-HM81-K
1 2 3 4
5 6 7 8
SIDE A
A
H CP19 G CN511
CP606 CP512
B
C691
C
C714
D
X-HM81-K 93
5 6 7 8
1 2 3 4
SIDE B
A
D MAIN ASSY
CP512 CP606
B
D
94 X-HM81-K
1 2 3 4
5 6 7 8
SIDE B
A
CP509
B
CP604
CP605
CP602
D
X-HM81-K 95
5 6 7 8
1 2 3 4
E BCO ASSY
CP6
C
CP500
CP2
J
C
CN702
CP5
M CP4
CP1
F
CP8 CP7
G CP12 G CP11
E
96 X-HM81-K
1 2 3 4
5 6 7 8
SIDE B SIDE B
A
E BCO ASSY
B
CP6
CP2
CP5
CP1
CP7 CP8
Q7 Q8 Q3 Q4 Q9
IC19 IC12 IC9 IC5 IC2 IC13 Q10
IC18 IC4 IC8 Q101
E
X-HM81-K 97
5 6 7 8
1 2 3 4
CP605
CP712
D
B
D
K CN
CP505 CP506
CN511
H CP31 H CP30
CP18
D CP512
D CP509
Q17 Q14
Q15
IC704 IC701
F G H
98 X-HM81-K
1 2 3 4
5 6 7 8
SIDE A
A
CP312
CP710
N
B
CP506
CP30
G
CP505
D
K CN515
CP31
Y
G
CP607
CP19
9 D CP606
F H
X-HM81-K 99
5 6 7 8
1 2 3 4
SIDE B
A
F CNT1 ASSY
CP710
C
CP30
D
CP31
CP19
F H
100 X-HM81-K
1 2 3 4
5 6 7 8
SIDE B
A
CN702
CP712
B
D
K FPC515
CP607 FPC2
F G H
X-HM81-K 101
5 6 7 8
1 2 3 4
H FPC2
K FRONT ASSY FPC515
D CP602
D CN510 E CP2
7020-07253-000-0S
CP500
I F_AUX ASSY
J F_USB ASSY
I J K
102 X-HM81-K
1 2 3 4
5 6 7 8
SIDE A
A
FPC2 H CP607
PC515 CN515
CP508 C
CN502
L KEY ASSY
M DOCKING ASSY
CP1
CP4
E
E
K L M
X-HM81-K 103
5 6 7 8
1 2 3 4
SIDE B
A
Q509 Q510 Q18
C CP508
L KEY ASSY
CN502
M DOCKING ASSY
CP4
K L M
104 X-HM81-K
1 2 3 4
5 6 7 8
SIDE B
A
Q18 Q508
5 FPC515
CN502
CN510 D
CP500
J F_USB ASSY
I F_AUX ASSY
I J K
X-HM81-K 105
5 6 7 8
1 2 3 4
100N
SUB TRANS
AC IN
CP301
F301
CP300
UK / AUST(DAB)
SIDE B
D
N POWER ASSY
CP301
N
106 X-HM81-K
1 2 3 4
5 6 7 8
SIDE A
Q303 Q307 Q311
IC303 IC301 IC313 IC311 Q305 A
A PN1705
CP310
T2.5A/250V T2.5A/250V
FUSE305
FUSE304
C
CP312
F CP710
SIDE B
CP312
CP310 F
Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47 k ohm (tolerance is shown by J = 5%,
and K = 10%).
560 Ω → 56 × 101 → 561 ................................................................... RD1/4PU 5 6 1 J
47 kΩ → 47 × 103 → 473 ................................................................... RD1/4PU 4 7 3 J
0.5 Ω → R50 ................................................................................................. RN2H R 5 0 K
1Ω → 1R0 ................................................................................................. RS1P 1 R 0 K
Ex.2 When there are 3 effective digits (such as in high precision metal film resistors).
5.62 kΩ → 562 × 101 → 5621 ................................................................. RN1/4PC 5 6 2 1 F
- Meaning of the figures and others in the parentheses in the parts list.
B
Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding PC board.
IC 301 (A, 91, 111) IC NJM2068V
LIST OF ASSEMBLIES
Mark Symbol and Description X-HM81-K/SYXE8 X-HM81-S/SYXE8 XC-HM81-K/SYXE8 XC-HM81-S/SYXE8
NSP 1..PCB TOTAL ASSY FRONT 7025MU1105030-IL 7025MU1105030-IL 7025MU1105030-IL 7025MU1105030-IL
2..FRONT ASSY 7028072531010-IL 7028072531010-IL 7028072531010-IL 7028072531010-IL
2..KEY ASSY 7028072533010-IL 7028072533010-IL 7028072533010-IL 7028072533010-IL
2..TUNER ASSY 7028072534030-IL 7028072534030-IL 7028072534030-IL 7028072534030-IL
2..F_AUX ASSY 7028072535010-IL 7028072535010-IL 7028072535010-IL 7028072535010-IL
2..F_USB ASSY 7028072536010-IL 7028072536010-IL 7028072536010-IL 7028072536010-IL
D 2..BT ASSY 7028072537010-IL 7028072537010-IL 7028072537010-IL 7028072537010-IL
NSP 1..PCB TOTAL ASSY POWER 7025MU1105031-IL 7025MU1105031-IL 7025MU1105031-IL 7025MU1105031-IL
2..MAIN ASSY 7028072541030-IL 7028072541030-IL 7028072541030-IL 7028072541030-IL
2..POWER ASSY 7028072542030-IL 7028072542030-IL 7028072542030-IL 7028072542030-IL
2..DOCKING ASSY 7028072544010-IL 7028072544010-IL 7028072544010-IL 7028072544010-IL
NSP 1..PCB TOTAL ASSY BRIDG 7025MU1105032-IL 7025MU1105032-IL 7025MU1105032-IL 7025MU1105032-IL
2..BCO ASSY 7028072551010-IL 7028072551010-IL 7028072551010-IL 7028072551010-IL
2..CNT2 ASSY 7028072552010-IL 7028072552010-IL 7028072552010-IL 7028072552010-IL
1...PCB TOTAL ASSY CD 7025MU1105034-IL 7025MU1105034-IL 7025MU1105034-IL 7025MU1105034-IL
2..CD ASSY 7028072301010-IL 7028072301010-IL 7028072301010-IL 7028072301010-IL
Mark Symbol and Description X-HM71-K/SYXE8 X-HM71-K/CXE X-HM71-S/SYXE8 X-HM71-S/AXQ5
NSP 1..PCB TOTAL ASSY FRONT 7025MU1106050-IL 7025MU1106020-IL 7025MU1106050-IL 7025MU1106020-IL
2..FRONT ASSY 7028072531010-IL 7028072531010-IL 7028072531010-IL 7028072531010-IL
E 2..KEY ASSY 7028072533010-IL 7028072533010-IL 7028072533010-IL 7028072533010-IL
2..TUNER ASSY 7028072534060-IL 7028072534040-IL 7028072534060-IL 7028072534040-IL
2..F_AUX ASSY 7028072535010-IL 7028072535010-IL 7028072535010-IL 7028072535010-IL
2..F_USB ASSY 7028072536010-IL 7028072536010-IL 7028072536010-IL 7028072536010-IL
2..BT ASSY Not used Not used Not used Not used
NSP 1..PCB TOTAL ASSY POWER 7025MU1106051-IL 7025MU1106021-IL 7025MU1106051-IL 7025MU1106031-IL
2..MAIN ASSY 7028072541060-IL 7028072541040-IL 7028072541060-IL 7028072541050-IL
2..POWER ASSY 7028072542030-IL 7028072542040-IL 7028072542030-IL 7028072542030-IL
2..DOCKING ASSY 7028072544010-IL 7028072544010-IL 7028072544010-IL 7028072544010-IL
NSP 1..PCB TOTAL ASSY BRIDG 7025MU1106022-IL 7025MU1106022-IL 7025MU1106022-IL 7025MU1106022-IL
2..BCO ASSY 7028072551020-IL 7028072551020-IL 7028072551020-IL 7028072551020-IL
2..CNT2 ASSY 7028072552020-IL 7028072552020-IL 7028072552020-IL 7028072552020-IL
1...PCB TOTAL ASSY CD 7025MU1105034-IL 7025MU1105034-IL 7025MU1105034-IL 7025MU1105034-IL
F
2..CD ASSY 7028072301010-IL 7028072301010-IL 7028072301010-IL 7028072301010-IL
108 X-HM81-K
1 2 3 4
5 6 7 8
B TUNER ASSY
7028072534030-IL, 7028072534060-IL and 7028072534040-IL are constructed the same except for the following:
A
D MAIN ASSY
7028072541030-IL, 7028072541060-IL, 7028072541040-IL and 7028072541050-IL are constructed the same except for the
following:
B
Mark Symbol and Description 7028072541030-IL 7028072541060-IL 7028072541040-IL 7028072541050-IL
JA600 TER, board Screw 4P G612405EWG02Y-IL G612405E0200Y-IL G612405E0200Y-IL G612405E0200Y-IL
E BCO ASSY
7028072551010-IL and 7028072551020-IL are different in part number, they consist of the same components.
G CNT2 ASSY
7028072552010-IL and 7028072552020-IL are different in part number, they consist of the same components.
C
N POWER ASSY
7028072542030-IL and 7028072542040-IL are constructed the same except for the following:
Mark Symbol and Description 7028072542030-IL 7028072542040-IL
> FU301 Fuse Glass Tube 20 mm N751502001160-IL N751506301160-IL
> T301 Power trans 8200660550500-IL 8200660550490-IL
> T302 Power trans 8200280150380-IL 8200280150390-IL
D
Mark No. Description Part No. Mark No. Description Part No.
PARTS LIST (X-HM81-K/SYXE8)
C BT ASSY
A CD ASSY
SEMICONDUCTORS
SEMICONDUCTORS
IC 600 J046222400010-IL
IC 1601 8952HM7100050-IL
D MAIN ASSY
IC 1602 J001126410010-IL
IC 1603 J005250400010-IL
IC 1604 8952HM7100040-IL
SEMICONDUCTORS
IC 1605 J126730270020-IL
IC 601 J000241600020-IL
IC 602,606 J121458001020-IL
IC 1606 J127586900010-IL E
IC 603 J040739100010-IL
IC 1607 J121458000020-IL
IC 605 J121456000041-IL
IC 607 J126781200040-IL
B TUNER ASSY
SEMICONDUCTORS
IC 608,612
IC 609
J080209201010-IL
8952HM7100010-IL
IC 400 J127256100010-IL
MISCELLANEOUS
JA 600 TER,BOARD SCREW 4P G612405EWG02Y-IL
MISCELLANEOUS RY 600 RELAY G680120502050-IL
JA 400 TER,RCA 1PIN G600107AGY00Y-IL
X 601 CRYSTAL (32.76796 kHz) E80032R768020-IL
JA 401 TER,RCA 2PIN G601207AEGG02-IL
JA 402 PIN JACK(1P) G600107AGF00Y-IL
RESISTORS F
400 TUNER,FM/AM E903104100780-IL
R 600,601 F320184710050-IL
X-HM81-K 109
5 6 7 8
1 2 3 4
Mark No. Description Part No. Mark No. Description Part No.
E BCO ASSY
SEMICONDUCTORS
IC 311
IC 313
J12678R080010-IL
J126111733050-IL
A IC 315 J126111700041-IL
IC 2 J126012010010-IL
IC 4 8952HM7100020-IL > D 307 K047100600010-IL
IC 5,9,13 J048121200010-IL D 309,311 K000400700220-IL
IC 8 341S2162 D 313,315,339,341 K000400700010-IL
IC 11,14 J046255700010-IL
D 325 K047800500010-IL
IC 12,18,19 J040330000010-IL D 328 K047604000020-IL
D 6,8,9 K120081200010-IL D 345,347 K000400700010-IL
MISCELLANEOUS MISCELLANEOUS
JA 1 JACK,MODULAR G4060RJ450120-IL > RY 301 RELAY G680060102020-IL
0 MODULE 8952HM7100030-IL > T 301 POWER TRANS 8200660550500-IL
> T 302 POWER TRANS 8200280150380-IL
B
CN 301 CN.WAFER 7.92MM L108396030010-IL
G CNT2 ASSY
> FU 301 FUSE GLASS TUBE 20MM N751502001160-IL
H F_AUX ASSY
MISCELLANEOUS
CAPACITORS
C 315,323 D040332087000-IL
JA 501,502 JACK,D3.5 G401035180010-IL C 329,367,377 D040332084030-IL
C C 335 D00847208H010-IL
C 341 D040102084060-IL
I F_USB ASSY
MISCELLANEOUS
C 395 D040102083030-IL
K FRONT ASSY
SEMICONDUCTORS
IC 500 E940349003810-IL
D 500,502 K500036001230-IL
D D 501 K500032001140-IL
MISCELLANEOUS
S 500 SW,ENCODER G121125072010-IL
S 506,510 SWITCH G180501000010-IL
RESISTORS
R 118 C060027065050-IL
L KEY ASSY
MISCELLANEOUS
E
S 500,502,504,508 SWITCH G180501000010-IL
S 512 SWITCH G180501000010-IL
M DOCKING ASSY
There is no service parts.
N POWER ASSY
SEMICONDUCTORS
F IC 301 J126781200040-IL
IC 303 J126791200060-IL
IC 305 J126780500450-IL
IC 307 J126790500130-IL
110 X-HM81-K
1 2 3 4