Beruflich Dokumente
Kultur Dokumente
IMPORTANT: For 3-Way applications, note that one of the screw terminals Step 4a cont'd Step 4b cont'd
TOOLS NEEDED TO INSTALL YOUR TIMER SWITCH from the old switch being removed will usually be a different color (Black)
Slotted/Phillips Screwdriver Electrical Tape Pliers or labeled Common. Tag that wire with electrical tape and identify as the Timer Switch Coordinating Remote Switch (no LED) Timer Switch
Pencil Cutters Ruler common (Line or Load) in both the switch wall box and remote wall box.
Changing the color of your device: White Black Hot (Black)
WH BK WH BK Hot (Black)
Your device may include color options. To change color of the face, Step 3 Preparing and connecting wires: (unused)
Green
proceed as follows: Pull off pre-cut insulation from timer switch leads. Make sure Ground Black
Green
Ground
Green
Ground
that the ends of the wires from the wall box are straight (cut if Red Yellow/Red RD YL/RD RD YL/RD
necessary). Remove insulation from each wire in the wall box Line
Black
(unused)
as shown: Insulating Line Load 120VAC, 60Hz
Label
120 VAC, 60Hz
Strip Gage Load
5/8" (measure bare White
Line up tabs and (1.6 cm) wire here)
Push in side press in sides one White
Cut Neutral (White)
at tab to release at a time to attach
(if necessary) Neutral (White)
WIRING TIMER SWITCH:
MAXIMUM LOAD PER TIMER FOR MULTI-DEVICE INSTALLATIONS Connect wires per WIRING DIAGRAM as follows:
Load Single Two Devices More than 2 devices For non-standard wiring applications, refer to WIRING TIMER SWITCH: NOTE: The timer switch must be installed in a wall box that has a Line
Wire Nut and Connector Size Chart Connect wires per WIRING DIAGRAM as follows: Hot connection.
Resistive Load 20A (2400W) 16A (1920W) 16A (1920W) • Green or bare copper wire in wall box to Green lead.
WIRE CONNECTOR / # OF COND. COMBINATION CHART NOTE: Maximum wire length from timer switch to all installed remote
Incandescent Load 1800W 1800W 1800W • Line Hot wall box wire to Black lead. switches cannot exceed 300 ft (90 m).
1 - #12 w/ 1 to 3 #14, #16 or #18 • Green or bare copper wire in wall box to Green lead.
• Load wall box wire to Red lead.
Inductive Load 20A 16A 16A 2 - #12 w/ 1 to 2 #16 or #18
1 - #14 w/ 1 to 4 #16 or #18 • Line Neutral wall box wire to White lead. • Line Hot (common) wall box wire identified (tagged) when removing
Motor Load 1HP 1HP 1HP 2 - #14 w/ 1 to 3 #16 or #18 • Timer Switch Yellow/Red lead should have Red insulation label affixed. old switch to Black lead.
• Proceed to Step 5. • First Traveler wall box wire to Red lead (note wire color).
INSTALLING YOUR TIMER SWITCH • Remove Red insulating label from Yellow/Red lead.
• Make sure that the ends of the wires from the wall box are
NOTE: Use check boxes when Steps are completed. straight (cut if necessary). Step 4b 3-Way Wiring with Vizia + Coordinating Remote • Second Traveler wall box wire to Yellow/Red lead (note wire color).
Switch (no LED) Application: This traveler from the timer switch must go to the terminal screw on
• Remove insulation from each wire in the wall box as shown. the remote switch marked "YL/RD".
Step 1 WARNING: TO AVOID FIRE SHOCK OR DEATH; TURN • For Single-Pole Application, go to Step 4a.
OFF POWER at circuit breaker or fuse and test that power is • Line Neutral wall box wire to White lead.
off before wiring! • For 3-Way Coordinating Remote Switch (no LEDs) Application, go to Step 4b. Coordinating Remote Switch Timer Switch
OFF ON OFF ON • For 3-Way Matching Remote Switch (with LEDs) Application, go to Step 4c. WIRING VIZIA + COORDINATING REMOTE SWITCH:
OFF
OFF
ON
ON
OFF
OFF
ON
ON
Connect wires per WIRING DIAGRAM as follows:
Black
Step 4a Single Pole Wiring Application: NOTE: "BK" and "RD" terminals on coordinating remote switch are
OFF ON OFF ON
OFF ON OFF ON
BK WH 1
OFF ON OFF ON unused. Tighten both screws.
2
White 2
NOTE: Maximum wire length from timer switch to last remote switch
1
is 300 ft (90 m).
Step 2 Identifying your wiring application (most common):
Black
3
NOTE: If the wiring in your wall box does not resemble any of 1 4
Yellow/Red
5 • Green or bare copper wire in wall box to Green terminal screw.
RD 5
these configurations, consult an electrician. YL/RD
• Load wall box wire identified (tagged) when removing old switch to
Red 4
Single Pole 3-Way White
First Traveler (note color as above).
2
1. Line (Hot) 1. Line or Load (see
Green
3 • Second Traveler wall box wire (note color as above) to terminal
2. Neutral IMPORTANT instruction) screw marked "YL/RD". This traveler from the remote switch must go
1 2 3. Ground 1 2
2. Neutral 4 to the Yellow/Red lead of the timer switch.
Red
4. Load 3 3. Ground • Remove White insulating label from terminal screw marked "WH".
3 4 4. First Traveler – note color 3 • Line Neutral wall box wire to terminal screw marked "WH".
4 5 Green
5. Second Traveler – note Yellow/Red • Proceed to Step 5.
color.
Insulating label:
This wire is used in 3-way installations only.
NOTE: For matching remote w/LEDs installation, For single pole installations, do not remove this insulating label.
the First Traveler becomes Line Hot.
Step 4c 3-Way Wiring with Vizia + Matching Step 5 Testing your Timer Switch prior to mounting in OPERATION TROUBLESHOOTING
Remote Switch (w/LED) Application: wall box:
• Position all wires to provide room in
outlet wall box for device. 1. To turn the load ON press one of the timer buttons. The green LED • Intermittent Operation
Matching Remote Switch Timer Switch adjacent to that button will illuminate and the timer will begin to - Load has a bad connection.
Additional • Ensure that the word “TOP” is facing
countdown for the selected timer period. - Wires not secured firmly to leads of timer switch
Neutral Wire up on device strap.
2. To select a different countdown time press the button corresponding to and/or remote switch.
Black
4 • Partially screw in mounting screws in
2 the desired time. The LED adjacent to that button will illuminate and the
wall box mounting holes. • Load does not turn ON and Locator LED does not turn ON
BK WH