Beruflich Dokumente
Kultur Dokumente
Commercial Trench
Drains
Type 6 curb profile
Continuous inlets
prevent ponding at
low points, helping to
reduce road surface
failure
A B C D
radius secton and ramps
Tested to resist front
impact. Complies with
AASHTO Curb Loading
requirements
ACO INFRASTRUCTURE
CurbDrain Leaflet
System Layout
Closing Cap
Polymer concrete cap closes end of
system.
Radius Curb
Radiused external faces and tapered ends
provide smooth transition around an external
radius of 12.5 or 25 feet. Radius curbs have
a small dimple on the end to enable easy
identification while parts are still on skid.
Other radius dimensions
and internal radii can be
achieved by mitering
ends. 2
Catch Basin
Two part catch basin has ductile iron top
with hinged access cover and polymer
concrete base. Allows
connection to large
underground pipes.
www.acoinfrastructure.us
Typical Applications
• Urban roads
• City centers
• Housing developments
• Parking lots
• Industrial areas
Access Curb
Drop Curbs Curb unit with ductile iron cover provides
Drop curbs allow continuation of drainage flow access into system for maintenance. Unit has
through curb at pedestrian crossings or other drill-outs on rear to fit 4” and 6” Schedule
drop curb locations. Available ‘right’ and ‘left’ 40 pipes. Front face is ‘blind’ - no inlets.
format. Connects standard curb and center Cover can be right or left handed to match
curb. A choice of gradient available for: traffic flow - if a vehicle mounts the curb
Non - ADA driveway access and cover is open, the cover will hinge shut
1 ADA compliant flared angles and not damage vehicle. ACO recommends
2 (2-part unit) access curbs are used on all runs, quantity
will vary depending upon layout
complexity.
Center Curb
Allows continuation of water flow through
lowest part of drop curb areas. 2 options:
a Driveway center curb with drainage inlets
- 1.65 sq. in. per ft. Ideal for vehicle
driveways, etc.
b Walkway center curb without drainage
inlets. Ideal for ADA and pedestrian
applications.
www.acoinfrastructure.us
CurbDrain ACO INFRASTRUCTURE
Parts Table
Description Part Length Invert Depth Overall Depth Weight
No inches mm inches mm inches mm lbs
Standard curb unit 92399 23.62 600 8.11 206 15.00 380 77.0
Radius curb (R12.5’) 92386 23.56 598 8.11 206 15.00 380 86.0
Radius curb (R25’) 92396 23.56 598 8.11 206 15.00 380 86.0
Driveway drop curb - left 97282 23.62 600 8.11 206 15.00 380 73.0
Driveway drop curb - right 97327 23.62 600 8.11 206 15.00 380 73.0
Driveway center curb - with inlets 97309 35.63 905 8.11 206 10.08 256 107.0
ADA walkway drop curb - left 1 of 2 92407 29.53 750 8.11 206 15.00 380 94.3
ADA walkway drop curb - left 2 of 2 92403 29.53 750 8.11 206 12.56 319 88.5
ADA walkway drop curb - right 1 of 2 92405 29.53 750 8.11 206 15.00 380 94.3
ADA walkway drop curb - right 2 of 2 92402 29.53 750 8.11 206 12.56 319 88.5
ADA walkway center curb 97316 35.63 905 8.11 206 10.08 256 106.1
90° Outside corner 97966 13.14 334 8.11 206 15.00 380 65.0
Closing end cap 97293 1.97 50 - - 15.00 380 16.0
Cross curb channel - gray 97968 48.00 1,223 8.11 206 9.09 231 106.0
Cross curb channel - black 97970 48.00 1,223 8.11 206 9.09 231 106.0
Access curb 92395 23.62 600 8.11 206 15.00 380 83.0
Catch basin 92390 23.62 600 42.56 1,080 44.00 1,118 528.0
CurbDrain - Testing
Slip-Resistance Testing Impact Testing Other ACO Infrastructure
Testing performed on curb surfaces. Testing performed on CurbDrain. Products
• TraffikDrain - 4” internal width trench drain
• ASTM D2047-04 Standard Test Method for • To emulate vehicle impact a custom test was with high intake grates
Static Coefficient of Friction of Polish-Coated created. A CurbDrain was positioned to allow a
• HighwayDrain - 8” internal width monolithic
Flooring Surfaces as Measured by the James weight to be dropped perpendicularly onto the
trench drain
Machine. face from various heights. The test area was
covered with part of a tire to simulate reality. • BridgeDrain - 8” internal width fiberglass
• Results for ACO CurbDrain surfaces:
An electronic magnet was used to raise, hold bridge scupper
Dry: Static Coefficient of Friction = 0.83
Wet: Static Coefficient of Friction = 0.84 and release a weighted bar at required height. • Qmax® - high capacity slot drainage
Five drops were made on the same unit from
increasing heights. Results showed the unit
A static coefficient of friction of 0.50 or
could withstand 114 lbs dropped from a height
greater is generally accepted for classifying a
of 6’-4”.
walking surface as ‘slip-resistant’.
West Sales Office Northeast Sales Office Southeast Sales Office Follow us on
825 W. Beechcraft St. 9470 Pinecone Dr. 4211 Pleasant Road
Casa Grande, AZ 85122 Mentor, OH 44060 Fort Mill, SC 29708
Tel: (520) 421-9988 Tel: (440) 639-7230 Tel: (800) 543-4764 Electronic Contact:
(888) 490-9552 (800) 543-4764 Fax: (803) 802-1063 info@acousa.com
Fax: (520) 421-9899 Fax: (440) 639-7235 www.acoinfrastructure.us
© July 2015 ACO Polymer Products, Inc.
This information is believed to be accurate but it is not guaranteed to be so. We cannot assume liability for results that buyer obtains with our product since conditions of use
are beyond the control of the company. It is the customer’s responsibility to evaluate suitability and safety of product for his own use. ACO Polymer Products Inc. reserves the
right to change the product and specifications without notice. Re-order RD016