Sie sind auf Seite 1von 17

Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.

lp8o
===========================================================
=====================

LPile for Windows, Version 2015-08.003

Analysis of Individual Piles and Drilled Shafts


Subjected to Lateral Loading Using the p-y Method
© 1985-2015 by Ensoft, Inc.
All Rights Reserved

===========================================================
=====================

This copy of LPile is being used by:

PRIODEEP
DCL
This copy of LPile is licensed for exclusive use by:

,,

Use of this program by any entity other than , ,


is a violation of the software license agreement.

--------------------------------------------------------------------------------
Files Used for Analysis
--------------------------------------------------------------------------------

Path to file locations:


\Ensoft\Lpile2015-Examples\Example 2 Drilled Shaft in Sloping Ground\

Name of input data file:


Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8d

Name of output report file:


Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8o

Name of plot output file:


Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8p

Name of runtime message file:


Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8r

--------------------------------------------------------------------------------
Date and Time of Analysis
--------------------------------------------------------------------------------

Date: August 25, 2017 Time: 23:38:16

Page 1
Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8o

--------------------------------------------------------------------------------
Problem Title
--------------------------------------------------------------------------------

Example 2 Bored Pile Supporting a Retaining Wall (Final Run)

Job Number:

Client:

Engineer:

Description:

--------------------------------------------------------------------------------
Program Options and Settings
--------------------------------------------------------------------------------

Computational Options:
- Use unfactored loads in computations (conventional analysis)
Engineering Units Used for Data Input and Computations:
- International System Units (kilonewtons, meters, millimeters)

Analysis Control Options:


- Maximum number of iterations allowed = 975
- Deflection tolerance for convergence = 1.0000E-05 m
- Maximum allowable deflection = 3.7300 m
- Number of pile increments = 100

Loading Type and Number of Cycles of Loading:


- Static loading specified

- Use of p-y modification factors for p-y curves not selected


- No distributed lateral loads are entered
- Loading by lateral soil movements acting on pile not selected
- Input of shear resistance at the pile tip not selected
- Computation of pile-head foundation stiffness matrix not selected
- Push-over analysis of pile not selected
- Buckling analysis of pile not selected

Output Options:
- Output files use decimal points to denote decimal symbols.
- Values of pile-head deflection, bending moment, shear force, and
soil reaction are printed for full length of pile.
- Printing Increment (nodal spacing of output points) = 1
- No p-y curves to be computed and reported for user-specified depths
Page 2
Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8o
- Print using narrow report formats
(Note: Some output information is omitted from the narrow report formats)

--------------------------------------------------------------------------------
Pile Structural Properties and Geometry
--------------------------------------------------------------------------------

Total number of pile sections = 1

Total length of pile = 10.00 m

Depth of ground surface below top of pile = 0.00 m

Pile diameters used for p-y curve computations are defined using 2 points.

p-y curves are computed using pile diameter values interpolated with depth over

the length of the pile.

Point Depth Pile


X Diameter
m m
----- --------- -----------
1 0.00000 0.76000000
2 10.0000000 0.76000000

Input Structural Properties:


----------------------------

Pile Section No. 1:

Section Type = Drilled Shaft (Bored Pile)


Section Length = 10.000000 m
Section Diameter = 0.760000 m
Shear Capacity of Section = 0.0000 kN

--------------------------------------------------------------------------------
Ground Slope and Pile Batter Angles
--------------------------------------------------------------------------------

Ground Slope Angle = 10.000 degrees


= 0.175 radians

Pile Batter Angle = 0.000 degrees


Page 3
Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8o
= 0.000 radians

--------------------------------------------------------------------------------
Soil and Rock Layering Information
--------------------------------------------------------------------------------

The soil profile is modelled using 2 layers

Layer 1 is stiff clay without free water

Distance from top of pile to top of layer = 0.0000 m


Distance from top of pile to bottom of layer = 5.000000 m
Effective unit weight at top of layer = 18.700000 kN/m3
Effective unit weight at bottom of layer = 18.700000 kN/m3
Undrained cohesion at top of layer = 96.500000 kPa
Undrained cohesion at bottom of layer = 96.500000 kPa
Epsilon-50 at top of layer = 0.007000
Epsilon-50 at bottom of layer = 0.007000

Layer 2 is sand, p-y criteria by Reese et al., 1974

Distance from top of pile to top of layer = 5.000000 m


Distance from top of pile to bottom of layer = 15.200000 m
Effective unit weight at top of layer = 9.900000 kN/m3
Effective unit weight at bottom of layer = 9.900000 kN/m3
Friction angle at top of layer = 35.000000 deg.
Friction angle at bottom of layer = 35.000000 deg.
Subgrade k at top of layer = 16300. kN/m3
Subgrade k at bottom of layer = 16300. kN/m3

(Depth of lowest soil layer extends 5.20 m below pile tip)

--------------------------------------------------------------------------------
Static Loading Type
--------------------------------------------------------------------------------

Static loading criteria were used when computing p-y curves for all analyses.

--------------------------------------------------------------------------------
Pile-head Loading and Pile-head Fixity Conditions
--------------------------------------------------------------------------------

Number of loads specified = 2

Load Load Condition Condition Axial Thrust


Page 4
Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8o
No. Type 1 2 Force, kN
----- ---- -------------------- ----------------------- ----------------
1 1 V = 346.000000 kN M = 0.0000 m-kN 88.800000000
2 2 V = 352.000000 kN S = 0.0000 m/m 88.800000000

V = perpendicular shear force applied to pile head


M = bending moment applied to pile head
y = lateral deflection relative to pile axis
S = pile slope relative to original pile batter angle
R = rotational stiffness applied to pile head
Values of top y vs. pile lengths can be computed only for load types with
specified shear loading.
Axial thrust is assumed to be acting axially for all pile batter angles.

--------------------------------------------------------------------------------
Computations of Nominal Moment Capacity and Nonlinear Bending Stiffness
--------------------------------------------------------------------------------

Axial thrust force values were determined from pile-head loading conditions

Number of Pile Sections Analyzed = 1

Pile Section No. 1:


-------------------

Dimensions and Properties of Drilled Shaft (Bored Pile):


--------------------------------------------------------

Length of Section = 10.000000 m


Shaft Diameter = 0.760000m
Concrete Cover Thickness = 0.063400m
Number of Reinforcing Bars = 12 bars
Yield Stress of Reinforcing Bars = 414000.kPa
Modulus of Elasticity of Reinforcing Bars = 200000000.kPa
Gross Area of Shaft = 0.453646sq. m
Total Area of Reinforcing Steel = 0.006116sq. m
Area Ratio of Steel Reinforcement = 1.35 percent
Edge-to-Edge Bar Spacing = 0.131910m
Maximum Concrete Aggregate Size = 0.019050m
Ratio of Bar Spacing to Aggregate Size = 6.92
Offset of Center of Rebar Cage from Center of Pile = 0.0000m

Axial Structural Capacities:


----------------------------

Nom. Axial Structural Capacity = 0.85 Fc Ac + Fy As = 13031.123 kN


Tensile Load for Cracking of Concrete = -1424.929 kN
Nominal Axial Tensile Capacity = -2532.072 kN

Page 5
Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8o

Reinforcing Bar Dimensions and Positions Used in Computations:

Bar Bar Diam. Bar Area X Y


Number meters sq. m. meters meters
---------- ---------- ---------- ---------- ----------
1 0.025400 0.0005097 0.303900 0.00000
2 0.025400 0.0005097 0.263185 0.151950
3 0.025400 0.0005097 0.151950 0.263185
4 0.025400 0.0005097 0.00000 0.303900
5 0.025400 0.0005097 -0.151950 0.263185
6 0.025400 0.0005097 -0.263185 0.151950
7 0.025400 0.0005097 -0.303900 0.00000
8 0.025400 0.0005097 -0.263185 -0.151950
9 0.025400 0.0005097 -0.151950 -0.263185
10 0.025400 0.0005097 0.00000 -0.303900
11 0.025400 0.0005097 0.151950 -0.263185
12 0.025400 0.0005097 0.263185 -0.151950

NOTE: The positions of the above rebars were computed by LPile

Minimum spacing between any two bars not equal to zero = 0.131910 meters
between bars 7 and 8

Spacing to aggregate size ratio = 6.924421

Concrete Properties:
--------------------

Compressive Strength of Concrete = 27600. kPa


Modulus of Elasticity of Concrete = 24865024. kPa
Modulus of Rupture of Concrete = -3272. kPa
Compression Strain at Peak Stress = 0.001887
Tensile Strain at Fracture of Concrete = -0.0001154
Maximum Coarse Aggregate Size = 0.019050 m

Number of Axial Thrust Force Values Determined from Pile-head Loadings = 1

Number Axial Thrust Force


kN
------ ------------------
1 88.800

Definitions of Run Messages and Notes:


--------------------------------------

C = concrete in section has cracked in tension.


Page 6
Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8o
Y = stress in reinforcing steel has reached yield stress.
T = ACI 318 criteria for tension-controlled section met, tensile strain in
reinforcement exceeds 0.005 while simultaneously compressive strain in
concrete more than 0.003. See ACI 318, Section 10.3.4.
Z = depth of tensile zone in concrete section is less than 10 percent of
section depth.

Bending Stiffness (EI) = Computed Bending Moment / Curvature.


Position of neutral axis is measured from edge of compression side of pile.
Compressive stresses and strains are positive in sign.
Tensile stresses and strains are negative in sign.

Axial Thrust Force = 88.800 kN

Bending Bending Bending Depth to Run


Curvature Moment Stiffness N Axis Msg
rad/m kN-m kN-m2 m
---------------- ---------------- ---------------- ---------------- ---
0.0000492126 25.8556422625 525387. 0.5065677190
0.0000984252 51.5760139729 524012. 0.4435232292
0.0001476378 77.1407939491 522500. 0.4225126403
0.0001968504 102.5496752849 520952. 0.4120088763
0.0002460630 127.8026192274 519390. 0.4057075798
0.0002952756 152.8996162316 517820. 0.4015074477
0.0003444882 152.8996162316 443846. 0.2571814807 C
0.0003937008 152.8996162316 388365. 0.2508340752 C
0.0004429134 152.8996162316 345213. 0.2458106653 C
0.0004921260 152.8996162316 310692. 0.2417051312 C
0.0005413386 152.8996162316 282447. 0.2383256980 C
0.0005905512 152.8996162316 258910. 0.2354587034 C
0.0006397638 152.8996162316 238994. 0.2330451960 C
0.0006889764 152.8996162316 221923. 0.2309612667 C
0.0007381890 152.8996162316 207128. 0.2291306548 C
0.0007874016 152.8996162316 194183. 0.2275392143 C
0.0008366142 152.8996162316 182760. 0.2261447786 C
0.0008858268 152.8996162316 172607. 0.2249145514 C
0.0009350394 152.8996162316 163522. 0.2238098126 C
0.0009842520 152.8996162316 155346. 0.2228023062 C
0.0010334646 152.8996162316 147949. 0.2218989632 C
0.0010826772 152.8996162316 141224. 0.2210856136 C
0.0011318898 152.9235098863 135105. 0.2203505518 C
0.0011811024 158.8199604179 134468. 0.2196840235 C
0.0012303150 164.7114197338 133877. 0.2190778352 C
0.0012795276 170.5978687155 133329. 0.2185250544 C
0.0013287402 176.4792881037 132817. 0.2180197756 C
0.0013779528 182.3556584973 132338. 0.2175569375 C
0.0014271654 188.2269603510 131889. 0.2171321768 C
0.0014763780 194.0931739743 131466. 0.2167417125 C
0.0015255906 199.9537216901 131066. 0.2163741751 C
0.0015748032 205.8088289721 130689. 0.2160305118 C
Page 7
Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8o
0.0016240158 211.6588320775 130331. 0.2157133491 C
0.0016732284 217.5037102849 129990. 0.2154203745 C
0.0017224410 223.3434126181 129667. 0.2151495402 C
0.0017716536 229.1779810312 129358. 0.2148990261 C
0.0018208662 235.0073610684 129064. 0.2146672092 C
0.0018700788 240.8315313527 128781. 0.2144526373 C
0.0019192914 246.6504703269 128511. 0.2142540075 C
0.0020177166 258.2725834141 128002. 0.2138999994 C
0.0021161418 269.8734887715 127531. 0.2135971005 C
0.0022145670 281.4530273681 127092. 0.2133386667 C
0.0023129922 293.0109821012 126680. 0.2131191877 C
0.0024114174 304.5472462578 126294. 0.2129340560 C
0.0025098426 316.0615872227 125929. 0.2127793893 C
0.0026082677 327.5538139050 125583. 0.2126518945 C
0.0027066929 339.0237319266 125254. 0.2125487600 C
0.0028051181 350.4711435401 124940. 0.2124675718 C
0.0029035433 361.8958475456 124639. 0.2124062458 C
0.0030019685 373.2976392127 124351. 0.2123629740 C
0.0031003937 384.6763101879 124073. 0.2123361806 C
0.0031988189 396.0316484015 123806. 0.2123244866 C
0.0032972441 407.3634379730 123547. 0.2123266803 C
0.0033956693 418.6714591088 123296. 0.2123416931 C
0.0034940945 429.9554879990 123052. 0.2123685794 C
0.0035925197 441.2152967096 122815. 0.2124065001 C
0.0036909449 452.4506530667 122584. 0.2124547082 C
0.0037893701 463.6613205451 122358. 0.2125125369 C
0.0038877953 474.8470581404 122138. 0.2125793898 CY
0.0039862205 486.0076202497 121922. 0.2126547318 CY
0.0040846457 497.1427565377 121710. 0.2127380824 CY
0.0041830709 508.2522118005 121502. 0.2128290089 CY
0.0042814961 519.3357258269 121298. 0.2129271211 CY
0.0043799213 529.9313605361 120991. 0.2129705978 CY
0.0044783465 539.4489169654 120457. 0.2128829297 CY
0.0045767717 548.2978172840 119800. 0.2127228503 CY
0.0046751969 557.0063585484 119141. 0.2125625698 CY
0.0047736221 565.0200185040 118363. 0.2123260798 CY
0.0048720473 571.3641344570 117274. 0.2118837553 CY
0.0049704725 576.2542807261 115936. 0.2112707680 CY
0.0050688977 580.8685429681 114595. 0.2106519316 CY
0.0051673229 585.4708534320 113303. 0.2100621845 CY
0.0052657481 590.0618986743 112057. 0.2095000400 CY
0.0053641733 594.6407208618 110854. 0.2089622439 CY
0.0054625985 599.1964629586 109691. 0.2084256149 CY
0.0055610237 603.7410616602 108567. 0.2079134579 CY
0.0056594489 608.2744303073 107479. 0.2074245423 CY
0.0057578741 612.7964809832 106428. 0.2069577225 CY
0.0058562993 617.3071244932 105409. 0.2065119307 CY
0.0062500001 634.7476107890 101560. 0.2048477066 CY
0.0066437009 644.3672057586 96989. 0.2023439015 CY
0.0070374017 651.4097458769 92564. 0.1997462567 CY
0.0074311025 658.3152829665 88589. 0.1974246407 CY
Page 8
Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8o
0.0078248032 665.1247513515 85002. 0.1953845630 CY
0.0082185040 671.8256780002 81745. 0.1935734843 CY
0.0086122048 678.3603056209 78767. 0.1918853414 CY
0.0090059056 684.7961137835 76039. 0.1903901627 CY
0.0093996064 691.1300521572 73528. 0.1890650805 CY
0.0097933072 697.3589049634 71208. 0.1878909942 CY
0.0101870080 703.3843514467 69047. 0.1868337168 CY
0.0105807088 708.3166411881 66944. 0.1856860274 CY
0.0109744096 711.4524004014 64828. 0.1842818180 CY
0.0113681104 713.3152313310 62747. 0.1827680236 CY
0.0117618112 714.8075955663 60774. 0.1813223072 CY
0.0121555120 716.2482576595 58924. 0.1799985330 CY
0.0125492128 717.6379355289 57186. 0.1787853421 CY
0.0129429135 718.9132279019 55545. 0.1775886294 CY
0.0133366143 720.1387702720 53997. 0.1764693078 CY
0.0137303151 721.3200633435 52535. 0.1754390139 CY
0.0141240159 722.4753422321 51152. 0.1744828045 CY
0.0145177167 723.5902445299 49842. 0.1736010079 CY
0.0149114175 724.6760887796 48599. 0.1727829921 CY
0.0153051183 725.7400902210 47418. 0.1720209092 CY
0.0156988191 726.7675118361 46294. 0.1713170848 CY
0.0160925199 727.7490389385 45223. 0.1706269898 CY
0.0164862207 728.6941236359 44200. 0.1699503320 CY
0.0168799215 729.6180421958 43224. 0.1693189012 CY
0.0172736223 730.5144229556 42291. 0.1687328585 CY
0.0176673230 731.3983468580 41398. 0.1681819111 CY
0.0180610238 732.2695527035 40544. 0.1676639400 CYT
0.0184547246 733.1245113881 39726. 0.1671786850 CYT
0.0188484254 733.9546273444 38940. 0.1667284704 CYT
0.0192421262 734.7750277753 38186. 0.1663037568 CYT
0.0196358270 735.5855262036 37461. 0.1659031390 CYT
0.0200295278 736.3859302867 36765. 0.1655253271 CYT
0.0204232286 737.1701560592 36095. 0.1651721677 CYT
0.0208169294 737.9172121009 35448. 0.1648520155 CYT
0.0212106302 738.6373393820 34824. 0.1645580719 CYT
0.0216043310 739.3493611271 34222. 0.1642806170 CYT
0.0239665357 740.3941301666 30893. 0.1637404998 CYT

--------------------------------------------------------------------------------
Summary of Results for Nominal (Unfactored) Moment Capacity for Section 1
--------------------------------------------------------------------------------

Moment values interpolated at maximum compressive strain = 0.003


or maximum developed moment if pile fails at smaller strains.

Load Axial Thrust Nominal Mom. Cap. Max. Comp.


No. kN kN-m Strain
---- ---------------- ------------------ ------------
1 88.800 731.838 0.00300000

Page 9
Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8o
Note that the values of moment capacity in the table above are not
factored by a strength reduction factor (phi-factor).

In ACI 318, the value of the strength reduction factor depends on whether
the transverse reinforcing steel bars are tied hoops (0.65) or spirals (0.70).

The above values should be multiplied by the appropriate strength reduction


factor to compute ultimate moment capacity according to ACI 318, Section
9.3.2.2 or the value required by the design standard being followed.

The following table presents factored moment capacities and corresponding


bending stiffnesses computed for common resistance factor values used for
reinforced concrete sections.

Axial Resist. Nominal Ult. (Fac) Ult. (Fac) Bend. Stiff.


Load Factor Moment Cap Ax. Thrust Moment Cap at Ult Mom
No. for Moment kN-m kN kN-m kN-m^2
----- ------------ ------------ ------------ ------------ ------------
1 0.65 731.837730 57.719998 475.694507 122121.

1 0.70 731.837730 62.159999 512.286403 121428.

1 0.75 731.837730 66.600000 548.878298 119756.

--------------------------------------------------------------------------------
Computed Values of Pile Loading and Deflection
for Lateral Loading for Load Case Number 1
--------------------------------------------------------------------------------

Pile-head conditions are Shear and Moment (Loading Type 1)

Shear force at pile head = 346.000 kN


Applied moment at pile head = 0.000 kN-m
Axial thrust load on pile head = 88.800 kN

Depth Deflect. Bending Shear Soil Res. Bending


X y Moment Force p Stiffness
meters meters kN-m kN kN/m kN-m^2
----------- ----------- ----------- ----------- ----------- -----------
0.000 0.03426 4.375E-09 346.00000 -118.49420 525387.
0.10000 0.03297 34.12157 334.04032 -120.69937 525387.
0.20000 0.03169 67.03608 321.86506 -122.80588 522959.
0.30000 0.03041 98.72242 309.48431 -124.80901 521134.
0.40000 0.02913 129.16050 296.90868 -126.70363 519289.
0.50000 0.02785 158.33133 284.14930 -128.48409 213126.
0.60000 0.02658 186.21665 271.21757 -130.15043 132039.
0.70000 0.02532 212.79922 258.12486 -131.70384 130263.
0.80000 0.02408 238.06330 244.88258 -133.14161 128914.
Page 10
Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8o
0.90000 0.02286 261.99432 231.50245 -134.46096 127846.
1.00000 0.02166 284.57892 217.99645 -135.65911 126977.
1.10000 0.02048 305.80493 204.37684 -136.73318 126253.
1.20000 0.01933 325.66146 190.65617 -137.68026 125638.
1.30000 0.01820 344.13889 176.84729 -138.49734 125111.
1.40000 0.01710 361.22889 162.96335 -139.18135 124656.
1.50000 0.01603 376.92452 149.01783 -139.72909 124261.
1.60000 0.01498 391.22016 135.02451 -140.13726 123917.
1.70000 0.01397 404.11162 120.99753 -140.40242 123620.
1.80000 0.01300 415.59615 106.95136 -140.52094 123363.
1.90000 0.01205 425.67249 92.90086 -140.48902 123143.
2.00000 0.01114 434.34086 78.86128 -140.30262 122958.
2.10000 0.01027 441.60307 64.84828 -139.95740 122807.
2.20000 0.009432 447.46252 50.87797 -139.44873 122685.
2.30000 0.008631 451.92424 36.96696 -138.77153 122595.
2.40000 0.007866 454.99496 23.13237 -137.92027 122532.
2.50000 0.007139 456.68319 9.39191 -136.88879 122498.
2.60000 0.006448 456.99922 -4.23603 -135.67019 122491.
2.70000 0.005796 455.95524 -17.73238 -134.25667 122513.
2.80000 0.005180 453.56538 -31.07717 -132.63922 122562.
2.90000 0.004601 449.84585 -44.24950 -130.80736 122637.
3.00000 0.004060 444.81499 -57.22730 -128.74865 122740.
3.10000 0.003554 438.49342 -69.98714 -126.44807 122872.
3.20000 0.003084 430.90420 -82.50390 -123.88719 123032.
3.30000 0.002649 422.07300 -94.75040 -121.04277 123222.
3.40000 0.002248 412.02833 -106.69678 -117.88493 123442.
3.50000 0.001881 400.80184 -118.30973 -114.37401 123696.
3.60000 0.001546 388.42874 -129.55121 -110.45562 123984.
3.70000 0.001242 374.94830 -140.37659 -106.05199 124311.
3.80000 0.000969 360.40466 -150.73149 -101.04589 124679.
3.90000 0.000724 344.84800 -160.54617 -95.24786 125093.
4.00000 0.000507 328.33641 -169.72454 -88.31937 125562.
4.10000 0.000317 310.93930 -178.11812 -79.55229 126090.
4.20000 0.000150 292.74448 -185.44315 -66.94834 126692.
4.30000 7.392E-06 273.87813 -189.71913 -18.57118 127378.
4.40000 -0.000114 254.82415 -186.07980 91.35771 128152.
4.50000 -0.000216 236.68199 -176.08492 108.53985 128985.
4.60000 -0.000299 219.62359 -164.69495 119.25960 129876.
4.70000 -0.000366 203.75629 -152.38474 126.94459 130824.
4.80000 -0.000416 189.15706 -139.40017 132.74676 131826.
4.90000 -0.000453 175.88401 -125.90297 137.19730 132874.
5.00000 -0.000476 163.98177 -117.25523 35.75752 133975.
5.10000 -0.000487 152.43601 -113.59846 37.37774 464051.
5.20000 -0.000495 141.26373 -109.79076 38.77639 518481.
5.30000 -0.000500 130.47898 -105.85283 39.98223 519198.
5.40000 -0.000502 120.09383 -101.80376 40.99919 519799.
5.50000 -0.000502 110.11847 -97.66220 41.83188 520411.
5.60000 -0.000500 100.56123 -93.44633 42.48549 521047.
5.70000 -0.000497 91.42868 -89.17377 42.96578 521526.
5.80000 -0.000491 82.72564 -84.86154 43.27888 522081.
5.90000 -0.000484 74.45524 -80.52603 43.43137 522612.
Page 11
Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8o
6.00000 -0.000475 66.61902 -76.18295 43.43011 522983.
6.10000 -0.000465 59.21700 -71.84734 43.28217 523425.
6.20000 -0.000454 52.24769 -67.53349 42.99480 523956.
6.30000 -0.000442 45.70825 -63.25498 42.57540 524190.
6.40000 -0.000429 39.59448 -59.02464 42.03135 524431.
6.50000 -0.000416 33.90096 -54.85457 41.37003 524733.
6.60000 -0.000401 28.62108 -50.75613 40.59877 525122.
6.70000 -0.000386 23.74714 -46.73995 39.72481 525387.
6.80000 -0.000371 19.27041 -42.81595 38.75519 525387.
6.90000 -0.000355 15.18120 -38.99336 37.69674 525387.
7.00000 -0.000339 11.46893 -35.28072 36.55606 525387.
7.10000 -0.000323 8.12220 -31.68594 35.33945 525387.
7.20000 -0.000307 5.12885 -28.21632 34.05291 525387.
7.30000 -0.000290 2.47603 -24.87857 32.70212 525387.
7.40000 -0.000274 0.15022 -21.67885 31.29234 525387.
7.50000 -0.000257 -1.86267 -18.62281 29.82850 525387.
7.60000 -0.000241 -3.57727 -15.71563 28.31506 525387.
7.70000 -0.000225 -5.00871 -12.96207 26.75610 525387.
7.80000 -0.000208 -6.17259 -10.36650 25.15524 525387.
7.90000 -0.000192 -7.08490 -7.93296 23.51564 525387.
8.00000 -0.000176 -7.76204 -5.66517 21.84005 525387.
8.10000 -0.000160 -8.22077 -3.56663 20.13074 525387.
8.20000 -0.000144 -8.47817 -1.64062 18.38954 525387.
8.30000 -0.000129 -8.55167 0.10975 16.61785 525387.
8.40000 -0.000114 -8.45897 1.68147 14.81664 525387.
8.50000 -9.826E-05 -8.21810 3.07163 12.98648 525387.
8.60000 -8.317E-05 -7.84734 4.27733 11.12753 525387.
8.70000 -6.823E-05 -7.36530 5.29569 9.23962 525387.
8.80000 -5.343E-05 -6.79085 6.12378 7.32220 525387.
8.90000 -3.875E-05 -6.14316 6.75861 5.37445 525387.
9.00000 -2.420E-05 -5.44172 7.19710 3.39528 525387.
9.10000 -9.746E-06 -4.70632 7.43603 1.38335 525387.
9.20000 4.617E-06 -3.95707 7.47205 -0.66283 525387.
9.30000 1.890E-05 -3.21445 7.30167 -2.74490 525387.
9.40000 3.313E-05 -2.49927 6.92119 -4.86456 525387.
9.50000 4.731E-05 -1.83273 6.32679 -7.02354 525387.
9.60000 6.145E-05 -1.23643 5.51444 -9.22351 525387.
9.70000 7.557E-05 -0.73236 4.47996 -11.46601 525387.
9.80000 8.968E-05 -0.34294 3.21904 -13.75241 525387.
9.90000 0.000104 -0.09105 1.72723 -16.08378 525387.
10.00000 0.000118 0.000 0.000 -18.46085 525387.

Output Summary for Load Case No. 1:

Pile-head deflection = 0.03425789 meters


Computed slope at pile head = -0.01284190 radians
Maximum bending moment = 456.99922466 kN-m
Maximum shear force = 346.00000000 kN
Depth of maximum bending moment = 2.60000000 meters below pile head
Depth of maximum shear force = 0.000000 meters below pile head
Number of iterations = 31
Page 12
Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8o
Number of zero deflection points = 2

--------------------------------------------------------------------------------
Pile-head Deflection vs. Pile Length for Load Case 1
--------------------------------------------------------------------------------

Boundary Condition Type 1, Shear and Moment

Shear = 346. kN
Moment = 0. m-kN
Axial Load = 89. kN

Pile Pile Head Maximum Maximum


Length Deflection Moment Shear
meters meters kN-m kN
------------ ------------ ------------ ------------
10.00000 0.03425789 456.99922466 346.00000000
9.50000 0.03419988 457.17817985 346.00000000
9.00000 0.03422837 457.01624182 346.00000000
8.50000 0.03429187 456.85791666 346.00000000
8.00000 0.03422280 457.05496814 346.00000000
7.50000 0.03430306 456.71543505 345.99999999
7.00000 0.03442355 456.10684288 345.99999999
6.50000 0.03509659 453.45856504 345.99999999
6.00000 0.03688733 446.73440780 346.00000001
5.50000 0.04153092 432.44624132 346.00000001
5.00000 0.05959459 396.03387437 345.99999998
4.50000 0.09484545 357.42009464 346.00000005
4.00000 0.17087064 317.10364490 345.99999993

--------------------------------------------------------------------------------
Computed Values of Pile Loading and Deflection
for Lateral Loading for Load Case Number 2
--------------------------------------------------------------------------------

Pile-head conditions are Shear and Pile-head Rotation (Loading Type 2)

Shear force at pile head = 352.0 kN


Rotation of pile head = 0.000E+00 radians
Axial load at pile head = 88.8 kN

(Zero slope for this load indicates fixed-head conditions)

Depth Deflect. Bending Shear Soil Res. Bending


X y Moment Force p Stiffness
meters meters kN-m kN kN/m kN-m^2
----------- ----------- ----------- ----------- ----------- -----------
Page 13
Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8o
0.000 0.007562 -457.29870 352.00000 -81.27647 122488.
0.10000 0.007544 -422.50343 343.75956 -83.53234 122488.
0.20000 0.007491 -388.54041 335.29859 -85.68703 123984.
0.30000 0.007406 -355.43148 326.62722 -87.74032 124810.
0.40000 0.007293 -323.19743 317.75565 -89.69117 125715.
0.50000 0.007154 -291.85801 308.69417 -91.53840 126725.
0.60000 0.006993 -261.43192 299.45322 -93.28065 127875.
0.70000 0.006811 -231.93683 290.04336 -94.91648 129224.
0.80000 0.006610 -203.38930 280.47532 -96.44436 130850.
0.90000 0.006395 -175.80484 270.75997 -97.86273 132886.
1.00000 0.006166 -149.19783 260.90833 -99.17002 518024.
1.10000 0.005934 -123.58227 250.92988 -100.39902 519612.
1.20000 0.005700 -98.97049 240.83260 -101.54654 521127.
1.30000 0.005464 -75.37400 230.62481 -102.60911 522576.
1.40000 0.005226 -52.80348 220.31521 -103.58295 523914.
1.50000 0.004988 -31.26869 209.91287 -104.46391 524916.
1.60000 0.004749 -10.77849 199.42730 -105.24740 525387.
1.70000 0.004510 8.65925 188.86852 -105.92832 525387.
1.80000 0.004270 27.03769 178.24705 -106.50092 525258.
1.90000 0.004032 44.35108 167.57407 -106.95876 524234.
2.00000 0.003794 60.59481 156.86141 -107.29447 523327.
2.10000 0.003557 75.76549 146.12170 -107.49962 522553.
2.20000 0.003322 89.86104 135.36850 -107.56440 521611.
2.30000 0.003089 102.88080 124.61642 -107.47736 520922.
2.40000 0.002857 114.82561 113.88130 -107.22486 520102.
2.50000 0.002628 125.69797 103.18053 -106.79057 519493.
2.60000 0.002401 135.50222 92.53328 -106.15454 518842.
2.70000 0.002177 144.24468 81.96095 -105.29205 426364.
2.80000 0.001956 151.93393 71.48776 -104.17168 180402.
2.90000 0.001744 158.58071 61.13762 -102.83109 134488.
3.00000 0.001543 164.19813 50.93111 -101.29924 133923.
3.10000 0.001355 168.80147 40.88769 -99.56907 133489.
3.20000 0.001179 172.40800 31.02758 -97.63309 133165.
3.30000 0.001016 175.03704 21.37176 -95.48344 132938.
3.40000 0.000867 176.71009 11.94198 -93.11209 132797.
3.50000 0.000730 177.45083 2.76081 -90.51120 132736.
3.60000 0.000608 177.28527 -6.14844 -87.67392 132750.
3.70000 0.000498 176.24179 -14.76193 -84.59580 132839.
3.80000 0.000402 174.35117 -23.05560 -81.27753 133001.
3.90000 0.000318 171.64661 -31.00597 -77.73004 133238.
4.00000 0.000248 168.16360 -38.59169 -73.98427 133555.
4.10000 0.000190 163.93964 -45.79637 -70.10928 134040.
4.20000 0.000145 159.01350 -52.61512 -66.26578 215466.
4.30000 0.000107 153.42404 -59.03777 -62.18715 401199.
4.40000 7.254E-05 147.21237 -65.00546 -57.16677 518133.
4.50000 4.109E-05 140.42878 -70.37423 -50.20853 518534.
4.60000 1.235E-05 133.14287 -74.49604 -32.22766 519011.
4.70000 -1.382E-05 125.53445 -73.50151 52.11830 519508.
4.80000 -3.758E-05 118.44700 -67.25403 72.83128 519894.
4.90000 -5.906E-05 112.08766 -59.48713 82.50656 520283.
5.00000 -7.838E-05 106.55320 -55.06744 5.88729 520659.
Page 14
Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8o
5.10000 -9.566E-05 101.07743 -54.40603 7.34102 521024.
5.20000 -0.000111 95.67489 -53.60402 8.69905 521292.
5.30000 -0.000125 90.35918 -52.67106 9.96025 521588.
5.40000 -0.000136 85.14292 -51.61684 11.12407 521915.
5.50000 -0.000146 80.03776 -50.45112 12.19043 522277.
5.60000 -0.000155 75.05436 -49.18361 13.15976 522587.
5.70000 -0.000162 70.20244 -47.82398 14.03288 522803.
5.80000 -0.000168 65.49072 -46.38178 14.81102 523044.
5.90000 -0.000173 60.92701 -44.86644 15.49575 523313.
6.00000 -0.000176 56.51814 -43.28721 16.08897 523615.
6.10000 -0.000178 52.27008 -41.65311 16.59289 523954.
6.20000 -0.000180 48.18785 -39.97297 17.00996 524110.
6.30000 -0.000180 44.27564 -38.25533 17.34286 524241.
6.40000 -0.000180 40.53678 -36.50847 17.59440 524389.
6.50000 -0.000178 36.97380 -34.74037 17.76757 524558.
6.60000 -0.000177 33.58843 -32.95872 17.86551 524752.
6.70000 -0.000174 30.38166 -31.17087 17.89141 524977.
6.80000 -0.000171 27.35375 -29.38387 17.84857 525237.
6.90000 -0.000167 24.50428 -27.60443 17.74029 525387.
7.00000 -0.000163 21.83218 -25.83892 17.56989 525387.
7.10000 -0.000159 19.33573 -24.09339 17.34064 525387.
7.20000 -0.000154 17.01266 -22.37357 17.05579 525387.
7.30000 -0.000148 14.86012 -20.68485 16.71852 525387.
7.40000 -0.000143 12.87474 -19.03233 16.33192 525387.
7.50000 -0.000137 11.05266 -17.42079 15.89899 525387.
7.60000 -0.000131 9.38954 -15.85471 15.42260 525387.
7.70000 -0.000125 7.88064 -14.33830 14.90550 525387.
7.80000 -0.000119 6.52078 -12.87551 14.35028 525387.
7.90000 -0.000112 5.30441 -11.47003 13.75938 525387.
8.00000 -0.000106 4.22563 -10.12531 13.13505 525387.
8.10000 -9.933E-05 3.27818 -8.84459 12.47939 525387.
8.20000 -9.267E-05 2.45553 -7.63090 11.79430 525387.
8.30000 -8.597E-05 1.75082 -6.48711 11.08148 525387.
8.40000 -7.923E-05 1.15692 -5.41592 10.34247 525387.
8.50000 -7.248E-05 0.66644 -4.41986 9.57859 525387.
8.60000 -6.571E-05 0.27174 -3.50138 8.79098 525387.
8.70000 -5.893E-05 -0.03504 -2.66281 7.98060 525387.
8.80000 -5.216E-05 -0.26202 -1.90636 7.14823 525387.
8.90000 -4.539E-05 -0.41752 -1.23423 6.29446 525387.
9.00000 -3.863E-05 -0.51007 -0.64852 5.41975 525387.
9.10000 -3.188E-05 -0.54842 -0.15131 4.52436 525387.
9.20000 -2.513E-05 -0.54153 0.25533 3.60847 525387.
9.30000 -1.840E-05 -0.49855 0.56936 2.67209 525387.
9.40000 -1.168E-05 -0.42885 0.78872 1.71517 525387.
9.50000 -4.968E-06 -0.34200 0.91136 0.73754 525387.
9.60000 1.739E-06 -0.24777 0.93518 -0.26099 525387.
9.70000 8.441E-06 -0.15616 0.85810 -1.28068 525387.
9.80000 1.514E-05 -0.07734 0.67798 -2.32175 525387.
9.90000 2.184E-05 -0.02175 0.39267 -3.38444 525387.
10.00000 2.854E-05 0.000 0.000 -4.46890 525387.

Page 15
Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8o
Output Summary for Load Case No. 2:

Pile-head deflection = 0.00756239 meters


Computed slope at pile head = 0.000000 radians
Maximum bending moment = -457.29870051 kN-m
Maximum shear force = 352.00000000 kN
Depth of maximum bending moment = 0.000000 meters below pile head
Depth of maximum shear force = 0.000000 meters below pile head
Number of iterations = 23
Number of zero deflection points = 2

--------------------------------------------------------------------------------
Pile-head Deflection vs. Pile Length for Load Case 2
--------------------------------------------------------------------------------

Boundary Condition Type 2, Shear and Slope

Shear = 352. kN
Slope = 0.00000
Axial Load = 89. kN

Pile Pile Head Maximum Maximum


Length Deflection Moment Shear
meters meters kN-m kN
------------ ------------ ------------ ------------
10.00000 0.00756239 -457.29870051 352.00000000
9.50000 0.00755472 -457.82480432 352.00000000
9.00000 0.00755232 -457.44635180 352.00000000
8.50000 0.00760297 -456.17566316 352.00000000
8.00000 0.00755482 -457.77042488 352.00000000
7.50000 0.00758658 -457.46119167 352.00000000
7.00000 0.00766305 -456.77886114 352.00000000
6.50000 0.00782582 -456.01213508 352.00000000
6.00000 0.00817937 -454.88161692 352.00000000
5.50000 0.00885030 -455.23977185 352.00000000
5.00000 0.00977950 -477.56914087 352.00000000
4.50000 0.01093450 -513.51187701 352.00000000
4.00000 0.01164308 -546.65843418 352.00000000
3.50000 0.01172117 -570.88793940 352.00000000
3.00000 0.01284148 -553.09281813 352.00000000
2.50000 0.02289344 -473.50504226 352.00000002
2.00000 0.06261103 -377.50071397 352.00000005

--------------------------------------------------------------------------------
Summary of Pile-head Responses for Conventional Analyses
--------------------------------------------------------------------------------

Definitions of Pile-head Loading Conditions:


Page 16
Example 2d Drilled Shaft in Sloping Ground - Free-and Fixed-head Cases.lp8o

Load Type 1: Load 1 = Shear, V, kN, and Load 2 = Moment, M, kN-m


Load Type 2: Load 1 = Shear, V, kN, and Load 2 = Slope, S, radians
Load Type 3: Load 1 = Shear, V, kN, and Load 2 = Rot. Stiffness, R, kN-m/rad.
Load Type 4: Load 1 = Top Deflection, y, m, and Load 2 = Moment, M, kN-m
Load Type 5: Load 1 = Top Deflection, y, m, and Load 2 = Slope, S, radians

Load Pile-head Pile-head Max Shear Max Moment


Case Load Deflection Rotation in Pile in Pile
No. Type meters radians kN kN-m
---- ---- ------------ ------------ ------------ ------------
1 1 0.034258 -0.012842 346.000000 456.999225
2 2 0.007562 0.0000 352.000000 -457.298701

Maximum pile-head deflection = 0.034257892 meters


Maximum pile-head rotation = -0.012841899 radians

The analysis ended normally.

Page 17

Das könnte Ihnen auch gefallen