Beruflich Dokumente
Kultur Dokumente
www.vishay.com
Vishay Semiconductors
2.5 A Output Current IGBT and MOSFET Driver
FEATURES
• 2.5 A minimum peak output current
NC 1 8 VCC • 25 kV/μs minimum common mode rejection
(CMR) at VCM = 1500 V
A 2 7 VO
• ICC = 2.5 mA maximum supply current
C 3 6 VO • Under voltage lock-out (UVLO) with hysteresis
NC 4 5 VEE
• Wide operating VCC range: 15 V to 32 V
Shield
• 0.2 μs maximum pulse width distortion
20530_1
V
• Industrial temperature range: - 40 °C to 110 °C
D E
• 0.5 V maximum low level output voltage (VOL)
19813 • Reinforced insulation rated per DIN EN 60747-5-2
• Material categorization: For definitions of compliance
DESCRIPTION please see www.vishay.com/doc?99912
The VO3120 consists of a LED optically coupled to an
integrated circuit with a power output stage. This APPLICATIONS
optocoupler is ideally suited for driving power IGBTs and • Isolated IGBT/MOSFET gate driver
MOSFETs used in motor control inverter applications. The
• AC and brushless DC motor drives
high operating voltage range of the output stage provides
the drive voltages required by gate controlled devices. The • Induction stove top
voltage and current supplied by this optocoupler makes it • Industrial inverters
ideally suited for directly driving IGBTs with ratings up to • Switch mode power supplies (SMPS)
800 V/50 A. For IGBTs with higher ratings, the VO3120 can
• Uninterruptible power supplies (UPS)
be used to drive a discrete power stage which drives the
IGBT gate.
AGENCY APPROVALS
• UL - file no. E52744 system code H, double protection
• cUL - file no. E52744, equivalent to CSA bulletin 5A
• DIN EN 60747-5-2 (VDE 0884) and reinforced insulation
rating available with option 1
ORDERING INFORMATION
DIP-8
V O 3 1 2 0 x - X 0 # # T
TRUTH TABLE
VCC - VEE VCC - VEE
LED “POSITIVE GOING” “NEGATIVE GOING” V0
(TURN ON) (TURN OFF)
Off 0 V to 32 V 0 V to 32 V Low
On 0 V to 11 V 0 V to 9.5 V Low
On 11 V to 13.5 V 9.5 V to 12 V Transition
On 13.5 V to 32 V 12 V to 32 V High
THERMAL CHARACTERISTICS
PARAMETER SYMBOL VALUE UNIT
LED power dissipation Pdiss 45 mW TA
Thermal resistance, TA
θJED 200 °C/W
junction emitter to junction detector
Thermal resistance, case to ambient θCA 2645 °C/W
Note
• The thermal characteristics table above were measured at 25 °C and the thermal model is represented in the thermal network below. Each
resistance value given in this model can be used to calculate the temperatures at each node for a given operating condition. The thermal
resistance from board to ambient will be dependent on the type of PCB, layout and thickness of copper traces. For a detailed explanation
of the thermal model, please reference Vishay’s Thermal Characteristics of Optocouplers application note.
ELECTRICAL CHARACTERISTICS
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
VO = (VCC - 4 V) IOH (1) 0.5 A
High level output current
VO = (VCC - 15 V) IOH (2) 2.5 A
VO = (VEE + 2.5 V) IOL (1) 0.5 A
Low level output current
VO = (VEE + 15 V) IOL (2) 2.5 A
High level output voltage IO = - 100 mA VOH (3) VCC - 4 V
Low level output voltage IO = 100 mA VOL 0.2 0.5 V
High level supply current Output open, IF = 7 mA to 16 mA ICCH 2.5 mA
Output open,
Low level supply current ICCL 2.5 mA
VF = - 3 V to + 0.8 V
Threshold input current low to high IO = 0 mA, VO > 5 V IFLH 5 mA
Threshold input voltage high to low VFHL 0.8 V
Input forward voltage IF = 10 mA VF 1 1.6 V
Temperature coefficient of forward voltage IF = 10 mA ΔVF/ΔTA - 1.4 mV/°C
Input reverse breakdown voltage IR = 10 μA BVR 5 V
Input capacitance f = 1 MHz, VF = 0 V CIN 60 pF
VO ≥ 5 V VUVLO + 11 13.5 V
UVLO threshold
IF = 10 mA VUVLO - 9.5 12 V
UVLO hysteresis UVLOHYS 1.6 V
Notes
• Minimum and maximum values were tested over recommended operating conditions (TA = - 40 °C to 110 °C, IF(ON) = 7 mA to 16 mA,
VF(OFF) = - 3 V to 0.8 V, VCC = 15 V to 32 V, VEE = ground) unless otherwise specified. Typical values are characteristics of the device and are
the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements. All typical values
were measured at Tamb = 25 °C and with VCC - VEE = 32 V.
(1) Maximum pulse width = 50 μs, maximum duty cycle = 0.5 %.
(2) Maximum pulse width = 10 μs, maximum duty cycle = 0.2 %. This value is intended to allow for component tolerances for designs with
IO peak minimum = 2.5 A.
(3) In this test V
OH is measured with a dc load current. When driving capacitive loads VOH will approach VCC as IOH approaches zero A. Maximum
pulse width = 1 ms, maximum duty cycle = 20 %.
1 8 1 8
0.1 µF 0.1 µF
100 mA
+ 4V
2 7 2 7
IF = 7 mA + VCC = 15 V + VCC = 15 V
to 16 mA to 32 V to 32 V
3 6 3 6
VOL
IOH
4 5 4 5
20973-2 20974-1
1 8 1 8
0.1 µF 0.1 µF
I OL
2 7 +
2 7
VCC = 15 V
to 32 V IF + VCC = 15 V
+ VO > 5 V to 32 V
3 6 2.5 V 3 6
4 5 4 5
20975-1 20976-1
1 8 1 8
0.1 µF 0.1 µF
VOH
2 7 2 7
I F = 7 mA + VCC = 15 V + VCC
to 16 mA to 32 V IF = 10 mA
VO > 5 V
3 6 3 6
100 mA
4 5 4 5
20978
20977-1
SWITCHING CHARACTERISTICS
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Rg = 10 Ω, Cg = 10 nF, f = 10 kHz,
Propagation delay time to logic low output (1) duty cycle = 50 % tPHL 0.1 0.4 μs
Propagation delay time to logic high output (1) Rg = 10 Ω, Cg = 10 nF, f = 10 kHz, tPLH 0.1 0.4 μs
duty cycle = 50 %
Rg = 10 Ω, Cg = 10 nF, f = 10 kHz,
Pulse width distortion (2) PWD 0.2 μs
duty cycle = 50 %
Rg = 10 Ω, Cg = 10 nF, f = 10 kHz,
Rise time duty cycle = 50 % tr 0.1 μs
Rg = 10 Ω, Cg = 10 nF, f = 10 kHz,
Fall time duty cycle = 50 % tf 0.1 μs
1 8
0.1 µF IF
I F = 7 mA to 16 mA
+ VCC = 15 V
2 7 to 32 V tr tf
500 Ω
+ VO
10 kHz 90 %
50 % Duty 3 6 10 Ω
50 %
Cycle
10 nF OUT
10 %
4 5
t PLH t PHL
20979-1
dV V CM
1 8 =
IF dt Δt
0.1 μF
A
R 2 7 0V
+ + Δt
5V VO
3 6 V CC = 32 V V OH
VO
Switch at A: IF = 10 mA
4 5
VO V OL
Switch at B: IF = 0 mA
+
20980-1
V CM = 1500 V
0.0 0.35
VOL - Output Low Voltage (V)
IF = 16 mA
IOUT = - 100 mA 0.30
VOH - VCC - High Output
- 0.5
VCC = 32 V
Voltage Drop (V)
VEE = 0 V 0.25
- 1.0
0.20
- 1.5
0.15
- 2.0 VF = 0.8 V
0.10
IOUT = 100 mA
- 2.5 VCC = 32 V
0.05 VEE = 0 V
- 3.0 0.00
- 40 - 20 0 20 40 60 80 100 120 - 40 - 20 0 20 40 60 80 100 120
21745 Temperature (°C) 21748 Temperature (°C)
Fig. 9 - High Output Voltage Drop vs. Temperature Fig. 11 - Output Low Voltage vs. Temperature
4 3.5
IF = 0 mA
IOH - High Output Current (A)
Vout = 2.5 V
VCC = 15 V
3 VEE = 0 V
2.5
IF = 16 mA 1.5
Vout = (VCC - 4) V
1
VCC = 15 V
VEE = 0 V
0 0.5
- 40 - 20 0 20 40 60 80 100 120 - 40 - 20 0 20 40 60 80 100
21746 Temperature (°C) 21751 Temperature (°C)
Fig. 10 - High Output Current vs. Temperature Fig. 12 - Output Low Current vs. Temperature
5 2.5
IF = 0 mA IF = 10 mA for ICCH
VOL - Output Low Voltage (V)
110 °C
IF = 0 mA for ICCL
3 1.5
ICCH
25 °C
2 - 40 °C 1.0
ICCL
1 0.5
0 0.0
0.0 0.5 1.0 1.5 2.0 2.5 3.0 15 20 25 30 35
21747 IOL - Output Low Current (A) 21711 VCC - Supply Voltage (V)
Fig. 13 - Output Low Voltage vs. Output Low Current Fig. 16 - Supply Current vs. Supply Voltage
0 5.0
(VOH - VCC) Output High Voltage
- 40 °C 3.5
-4 25 °C
Drop (V)
3.0
-6 2.5
2.0
-8 1.5
IF = 16 mA
VCC = 15 V 1.0
- 10
VEE = 0 V 0.5
- 12 0.0
0 0.5 1 1.5 2 2.5 - 40 - 20 0 20 40 60 80 100 120
21749 IOH - Output High Current (A) 21750 Temperature (°C)
Fig. 14 - Output High Voltage Drop vs. Output High Current Fig. 17 - Low to High Current Threshold vs. Temperature
2.5 35
TA = 25 °C
ICC - Supply Current (mA)
30
VO - Output Voltage (V)
2.0
25
1.5 20
ICCH
15
1.0
IF = 16 mA for ICCH 10
IF = 0 mA for ICCL ICCL
0.5
VCC = 32 V 5
VEE = 0 V
0 0
- 40 - 20 0 20 40 60 80 100 120 0 1 2 3 4 5
21754 Temperature (°C) 21752 IF - Forward LED Current (mA)
500 500
VCC = 30 V, VEE = 0 V
IF = 10 mA, TA = 25 °C
IF = 10 mA, TA = 25 °C
Rg = 10 Ω, Cg = 10 nF
400 Cg = 10 nF
400 Duty cycle = 50 %
Duty cycle = 50 %
f = 10 kHz
f = 10 kHz
300
300
tPLH
200
tPHL
tPHL
200
100
tPLH
100 0
15 20 25 30 35 0 10 20 30 40 50
21714 VCC - Supply Voltage (V) 21717 Rg - Series Load Resistance (Ω)
Fig. 19 - Propagation Delay vs. Supply Voltage Fig. 22 - Propagation Delay vs. Series Load Resistance
500 500
VCC = 32 V, VEE = 0 V VCC = 30 V, VEE = 0 V
tp - Propagation Delay (ns)
0 0
- 40 - 15 10 35 60 85 110 0 20 40 60 80 100
21753 TA - Temperature (°C) 21718 Cg - Series Load Capacitance (nF)
Fig. 20 - Propagation Delay vs. Temperature Fig. 23 - Propagation Delay vs. Series Load Capacitance
500
VCC = 30 V, VEE = 0 V
tp - Propagation Delay (ns)
TA = 25 °C
400 Rg = 10 Ω, Cg = 10 nF
Duty cycle = 50 %
f = 10 kHz
300
tPHL
200
tPLH
100
0
6 8 10 12 14 16
21716 IF - Forward LED Current (mA)
4 3 2 1
6.645 ± 0.165
ISO method A
5 6 7 8
9.77 ± 0.14
0.95 ± 0.19
7.62 typ.
0.79
4° typ.
3.555 ± 0.255
6.095 ± 0.255
1.27 10°
0.70 ± 0.19 3.045 ± 0.255
3° to 9°
0.51 ± 0.05
2.54 typ.
0.25 ± 0.05 i178006
Option 7 Option 9
0.76 0.76
R 0.25 R 0.25
2.54 2.54
1.78 1.78
PACKAGE MARKING
VO3120
X007
V YWW H 68
Notes
• The VDE logo is only marked on option 1 parts.
• Tape and reel suffix (T) is not part of the package marking.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.