Beruflich Dokumente
Kultur Dokumente
MicroRex D21
NT 29 17 86 02
L
N
Safty notes
• Installation of these products should only be undertaken by a qualified electrician.
• The operational and electrical safety is only guaranteed, if the product is installed using its proper
accessories, in a position as specified in the installation instructions.
• Any interference with the product makes the guarantee void.
• If the time switch is mounted near equipment where heat produced raises the local ambient above 55°C. Then a space should be put
between the time switch and the equipment. 700W 700W 2500W 700W 2900W 900W
Function
The MicroRex D22 is a microprocessor controlled digital time switch. Eight programs of your choice can be stored and used to control the automatic operation of your electrical equipment. Each indi-
vidual weekday can have a separate program or you can have several days operating on the same „Block“ program. To program the MicroRex D22 a „picture“ is used and when this is complete the
chosen times are stored in the microprocessor memory. The MicroRex D22 makes available 2 separate switching channels. The summer-/winter changeover can be programmed for hand or automa-
tic operation.
Presentation 1. Starting
Liquid Crystal Display Approximately 30 seconds after the supply voltage is connected the symbols
appear on the LCD.
Symbol for Before any operations the complete memory must be reset.
Actual or „On“ time „Set actual time“
Weekday 1
State of output
1234567 2. Memory reset
Day number = On
= Off
„Off“ time
„Off“ days
S + OK press both at
the same time
Programming Buttons
Delete
3. Setting date and summer- / winter changeover
Choose function
Hand switch
1 Channel 1 This can only be done after a Reset.
Summer- / winter ± 1h C
changeover
Summer- / winter changeover can be made manually or automatically if set.
S OK
Setting the hours, minutes, Fixing the hours, minutes, If manual changeover is required choose no during the date input. Automatic
days and channels R days, channels and conti- changeover depends on your country / area. Choose the appropriate setting
for your country / area.
nuous switching
Code d
4. Setting actual time Press to change to off hour
9. Continuous switching
The switch condition must first be chosen
S Press until the Press once S Set off hour
correct day is set
S Press until the correct 1234567 Press as required
Press once hour is shown Press once
OK OK Display 1 = On
OK Press once or 1 = Off
S Press until the
correct month is set S Press until the correct minute is shown Set off minute
S
OK Press once to either
OK Press once OK Press once 1
OK Press once Display 1
1234567
S Press until the The weekday will shown
correct year is set automatically Display 1
OK If the clock is on the correct day press
OK Press once The time switch will remain in continuous
Actual time is now set „On“ or „Off“ position until it is changed.
S Choose Otherwise use S OK
(See table below) to set another day 9.1 Terminating continuous switching
5. Setting switching time Press once
The time switch returns immediately to
1
Choice Summer Summer Country / Each program has an On- and Off-time. program mode
Press once 1234567
begins ends area
No No Display 1 = Off 1
no changeover changeover OK Press once Press once 1234567 S Press
Enter here the date for the beginning of
S Set the On minutes S Press to choose the
H summer for your country / area as well as
number of days
the end of summertime. E.g. 31ST March is
(d1 to d99)
shown for the beginning of Summertime. In
the following years it starts on the same day OK Press once OK Press once 1
irrespective of the date. 1
Press several 1234567
1234567
times until correct END
S Set the Off hour
„picture“ is shown
In the above example the time switch
stays „On“ for 14 days. At 0:00 hours on
the 15th day the time switch returns to its
OK Press once program mode.
1
Press until the
actual time is shown 1234567
S Set the Off minutes 10.1 Terminating continuous
Setting of the beginning of summer switching
code 1 1
END Press once 1234567
Set the day 1
S
1234567
OK Press once
OK Press once
7. Delete switching times 11. Summer-/ Winter changeover
End of program
S Set the month
Press several times until This function is only available if no was
OK Press once correct „picture“ is shown chosen during date input for
5.2
5 5 Day Monday to Friday program summer- / winter selection (see 3)
C Press to delete program
Set the year and set a new programm
S
or- ±1h Press until the actual time goes forward
Press until this 1 hour (summer) or back 1 hour (winter)
OK Press once display appears 1234567
Set times as 5.1 above Press until the 1
The start date is set. actual time is shown 1234567