Beruflich Dokumente
Kultur Dokumente
Previous Screen
Welcome: j210tak
Product: TRACK-TYPE TRACTOR
Model: D10N TRACK-TYPE TRACTOR 3SK
Configuration: D10N Track-Type Tractor 3SK00001-UP (MACHINE)
POWERED BY 3412 Engine
i01604581
Disassembly Procedure
Start By:
a. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
NOTICE
Keep all parts clean from contaminants.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Type 1
Table 1
Required Tools
Illustration 1 g00573401
1. Remove bolt (1) that fastens gear (2) in position on the shaft.
Illustration 2 g00573420
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&called… 2/6
26/7/2018 D10N Track-Type Tractor 3SK00001-UP (MACHINE) POWERED BY 3412 Engine(SEBP2237 - 50) - Systems & Components
Illustration 3 g00573424
Illustration 4 g00573427
Typical example
4. Remove four bolts and cover (4). Remove two bolts (8) and retainer (7). Remove spring (6) and
plunger (5) from the oil pump housing. Inspect the ring on plunger (5). Replace the ring if the ring is
damaged.
Illustration 5 g00573472
Typical example
5. Use Tool (B) to remove two bearings (9) from cover (4), if the cover is equipped with bearings.
Illustration 6 g00573498
6. Remove two shaft assemblies (10) from the oil pump body.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&called… 3/6
26/7/2018 D10N Track-Type Tractor 3SK00001-UP (MACHINE) POWERED BY 3412 Engine(SEBP2237 - 50) - Systems & Components
Illustration 7 g00573504
7. Use Tool (B) to remove two bearings (12) from the oil pump body. Remove two dowels (13) from the
oil pump body.
Type 2
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1P-2322 Puller Assembly 1
Illustration 8 g00523264
Typical example
1. Remove the bolt and the washer that holds the drive gear (1) on the shaft.
2. Use Tooling (A) to remove the shaft. Remove the key from the shaft. Put alignment marks on the
pump in order to assemble the gear and the shaft properly.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&called… 4/6
26/7/2018 D10N Track-Type Tractor 3SK00001-UP (MACHINE) POWERED BY 3412 Engine(SEBP2237 - 50) - Systems & Components
Illustration 9 g00523266
Typical example
3. Remove retainer (3) from the bypass valve. Remove the spring and the bypass valve.
4. Remove bolts (4) from the pump body. Remove the pump body (2).
5. Use Tooling (B) to remove the bearing from the pump body (2).
Illustration 10 g00523267
6. Remove gear (7). Put identifying marks on the gears in order to be installed properly.
7. Remove spacer (6) from the main oil pump body (5). Use Tooling (B) to remove the bearing from the
spacer (6).
Note: Check condition of the spacer and the bearings. If the spacer or the bearings are damaged use
new parts for replacement.
8. Remove the gears from the main oil pump body (5).
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&called… 5/6
26/7/2018 D10N Track-Type Tractor 3SK00001-UP (MACHINE) POWERED BY 3412 Engine(SEBP2237 - 50) - Systems & Components
Illustration 11 g00523309
9. Use Tooling (B) to remove the bearings from the main oil pump body.
Copyright 1993 - 2018 Caterpillar Inc. Thu Jul 26 2018 10:42:09 GMT+0800 (Waktu Standar Tiongkok)
All Rights Reserved.
j210tak
Private Network For SIS Licensees.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&called… 6/6