Sie sind auf Seite 1von 3

Roll No Name of the Student ………………………………………

GANDHI INSTITUTE FOR TECHNOLOGY, BHUBANESWAR


FIFTH SEMESTER, 2016-17, Branch: ECE
FIBER OPTICS AND OPTOELECTRONIC DEVICES
Full Mark 10 QUIZ TEST (Set – 1) Time: 20 min.
Questions carry equal marks
1 In an optical fiber, the concept of Numerical aperture is applicable in describing the ability of
a. Light Collection, b. Light Scattering, c. Light Dispersion d. Light Polarization
2 . Which among the following do/does not support/s the soot formation process?
a. OVPO, b. MCVD, c. PCVD, d. All of the above
3. Which is the correct order of sequential steps for an electric arc fusion technique?
A. Pressing of fiber ends for fusion
B. Application of heat for smoothening of end-surfaces
C. Alignment of broken fiber edges
a. A, B, C, b. B, A, C, c. C, B, A , d. C, A, B
4 . In the fiber optic link, power transfer from one fiber to another and from fiber to detector
take place with _________coupling efficiency.
a. maximum b. stable, c. minimum, d. unpredictable
5 . The macroscopic bending losses show an exponential increase due to ________ in radius of
curvature.
a. Increase, b. Decrease, c. Stability, d. None of the above
6 Which among the following is/are responsible for generating attenuation of an optical power in fiber?
a . Absorption, b. Scattering, c. Waveguide effect,d. All of the above
7 . In the structure of fiber optic cable, the refractive index of core is always _______the refractive
index of cladding.
a. Less than, b. Equal to, c. Greater than, d. None of the above
8 . Why are plastic clad silica fiber optic cables not used widely?
a. Difficulty in connector application due to excessive plasticity in cladding
b. Difficulty in bonding
c. Insolubility in organic solvents
d. All of the above
9 . In the given equation, state what αr suggests;
a) Radius of curvature
b) Refractive index difference
c) Radiation attenuation coefficients
d) Constant of proportionality
10 . A multimode fiber has refractive indices n1= 1.15, n2=1.11 and an operating wavelength of 0.7μm. Find the
radius of curvature?
a) 8.60μm
b) 9.30μm
c) 9.1μm
d) 10.2μm
………………………………………
Roll No Name of the Student _____________________________

GANDHI INSTITUTE FOR TECHNOLOGY, BHUBANESWAR


FIFTH SEMESTER, 2016-17, Branch: ECE
FIBER OPTICS AND OPTOELECTRONIC DEVICES
Full Mark 10 Surprise Test (Set – 1) Time: 20 min.
1. Draw the generalized configuration of a fiber optic communication system

2. .What is the functions of core and cladding in an optical fiber? Why should their refractive indices be
different?

3. .Define numerical aperture of a fiber .On what factor does it depend?

4. A step index fiber has numerical aperture 0.17 and core diameter of 100µm. determine the normalized
frequency parameter of the fiber when light of wavelength 0.85 µm is transmitted through it .also estimate
the number of guided modes propagating in the fiber.

5. .What are the causes of attenuation in optical fiber?


GANDHI INSTITUTE FOR TECHNOLOGY, BHUBANESWAR
FIFTH SEMESTER, 2016-17, Branch: ECE
FIBER OPTICS AND OPTOELECTRONIC DEVICES

Full Marks: 50 Assignment-I Date of Submission:_____________


1. .What is total internal reflection ?why is it necessary to meet the condition of total internal reflection at he
core cladding interface
2. .Explain multipath time dispersion and material dispersion .how can these be minimised
3. .a plastic fiber of 1mm diameter has n1=1.496 and n2=1.40.calculae its NA and αm when it is placed in
(a)air and (b)water
4. .What is the significance of maxwells equation ?write these equations for the metallic and dielectric media
5. .Distinguish between propagation parameters k,β and b. how are they interrelated
6. .Distinguish between multimode step index and graded index fiber . what is the difference between
multimode and single mode fiber?
7. .A multimode SI fiber has a core diameter 50 µm, a core index of 1.46and a relative refractive index
difference of 1%.it is operating at a wavelength of 1.3µm. calculate (i)refractive index of the cladding
(ii)the normalized frequency parameter V,and (iii)the total number of modes guided by the fiber
8. .Explain intermodal and intramodal dispersions.
9. .What is meant by cutoff condition?
10. .Describe the fiber structures utilized to provide (a)dispersion shifting and (b)dispersion flattening in single
mode fibers

………………………………………………………………

Das könnte Ihnen auch gefallen