Beruflich Dokumente
Kultur Dokumente
w
w
.c
ar
-s
ol
ut
io
ns
.c
o m
Warning / Caution
When installing the main unit, do not remove or alter existing
vehicle fasteners, including nuts, bolts, screw, clips, and fittings.
m
Never detach, move or alter existing vehicle wiring, including
electrical grounds and straps. Alteration of existing vehicle
Warning components may make vehicle unsafe to operate. Should be
o
no any electronic devices or magnetic pole around installation
place.
.c
Air bags are vital part of a safety system. Never install main unit
in a way which will alter air bag wiring or interfere with air bag
deployment. Air bags must function properly in the event of an
ns
accident.
Before installing, check the location of pipe, tank, electrical
cables and others.
io
Read and follow the instruction manual.
Wiring location must not interfere driving, get in or out from car.
Use electrical tape to insulate the ends of all wires, even if they
ut
are not used. Proper insulation prevents arcs, shocks and fires.
When installation is complete, test all vehicle electrical systems
to ensure they operate correctly, including lights, horn, brake
ol
lights, and emergency flashers.
According to our sales policy, any problems caused by user’s
mistake, careless can not be guaranteed.
-s
ar
Caution step.
Do not install the main unit in places where it ma be exposed to
dew condensation (around the air conditioning hose, etc), or in
w
www.car-solutions.com
Table of Contents
m
1. Specifications
1.1 Main Specifications 1
o
1.2 Features 2
.c
1.3 System Diagram 3
1.4 Components 4
1.5 Exterior 5
ns
2. Installation
io
2.1 Installation Diagram 6
2.2 Installation 7
ut
3. Settings
3.1 DIP Switch 8
ol
3.2 Remote Control 9
3.3 Factory Menu
-s
3.3.3 UTIL2 14
3.4 Original Button Usage 18
.c
3.5 OSD 19
w
4. Trouble Shooting 21
w
w
www.car-solutions.com
1. Specifications
1.1 Main Specifications
1. Car Compatibility
m
NEW Audi without MMI 2008~
o
2. Components
Interface* 1EA
.c
3. MULTIMEDIA INTERFACE input specification
ns
3 * A/V input (video external input)
1 * CVBS(Rear Camera) input
1 * Analog RGB input (Navigation system output)
io
1 * LCD input (Car system input)
ut
4. MULTIMEDIA INTERFACE output specification
1 * LCD output
ol
5. Power specification
-s
detected
w
-1-
www.car-solutions.com
1. Specifications
1.2 Features
Easy installation through connection with command
m
Able to control NAVI, DVD, DTV function by using I-Drive
o
Controller
.c
Able to adjust DVD, NAVI display on screen
ns
Improved Screen Display (user-oriented interface)
io
Provide power cable to connect with rear camera
ut
Dynamic PAS(Parking assistance system)+PDC,
ol
moving parking line according movement of steering wheel
-s
ar
.c
w
w
w
-2-
www.car-solutions.com
1. Specification
1.3 System Diagram
o m
Switch for source toggle
.c
Remote control
OEM Button (Can Signal)
ns
NAVIGATION Input MCU
(Analog RGB)
io DISPLAY
Car Installation
A/V 1
ut OEM LCD
VIDEO MUX
A/V 2
VIDEO
ol
A/V 3 CIRCUIT
CVBS
-s
(Rear camera)
-3-
www.car-solutions.com
1. Specification
1.4 Components
m
LVDS OUT cable * 1ea LVDS IN cable * 1ea
o
(HLCDCA0008) (HLCDCA0025)
.c
TOUCH IN cable * 1ea
(HTOUCH0009)
ns
A/V cable * 1EA
io
ut (HAVCAB0002)
(HARETC0001)
TOUCH OUT cable * 1ea
(HTOUCH0004)
w
(HIRCAB0002)
w
-4-
www.car-solutions.com
1. Specifications
1.5 Exterior
m
Dimension
o
Width 160mm
.c
Length 97.5mm
Height 21.1mm
ns
⑬ ⑫⑪ ⑩ ⑨ ⑧
① MODE
io ② IR
ut
③ POWER
④ TOUCH OUT
ol
⑤ REAR
-s
⑥ RGB-IN(NAVI)
⑦ AV IN/OUT
ar
⑧ LVDS IN
.c
⑨ LVDS OUT
⑩ TOUCH IN
w
①② ③ ④ ⑤ ⑥ ⑦ ⑪ TEST
w
⑫ LED
w
⑬ DIP S/W
-5-
www.car-solutions.com
2. Installation
2.1 Installation Diagram
om
Connecting CAN wire
.c
ns
Provided TOUCH IN Cable
CAN Low
Command Behind of monitor
io
CAN High Provided LVDS OUT Cable
Original
Original LCD Cable
ut Monitor
ol
Provided LVDS IN Cable Touch screen
-s
ar
Audio R
.c
Audio L
AV/OUT Video
AV3
ACC (12V ~24V)
w
AV2
GND X+ AV1
CAN-H Y+ REAR C
REAR (12V OUT)
GND
CAN-L
w
X-
F-CAM-DET
Y-
SAFE
Touch Cable
REAR-C
w
NAVI-VS
R DATA (red)
G DATA (green)
IR-NAVI
B DATA (blue)
SYNC
GND
Navigation
IR-DVD
IR-DTV
-6-
www.car-solutions.com
2. Installation
2.2 Installation
1. Connecting LCD Cable
o m
.c
ns
io
ut
Connect LCD cable from monitor with LVDS IN cable (provided).
ol
Connect LVDS IN cable’s other side with LVDS IN on our interface.
-s
ar
.c
w
w
w
Connect LVDS OUT cable (provided) with existing original monitor (on
the back side), and on the other side of cable connect with LVDS OUT
from our interface.
-7-
www.car-solutions.com
2. Installation
2.2 Installation
2. Connecting CAN Wires
m
Connection to CAN wires is performed behind the climate-control unit.
o
.c
ns
Car original CAN High cable
-8-
www.car-solutions.com
3. Settings
3.1 DIP Switch ※ Example DIP S/W usage
- Use input mode : A/V2, A/V3
- Use original navigation
m
- External rear camera
o
▷DIP S/W : 3 OFF (A/V2 display)
.c
▷DIP S/W : 4 OFF (A/V3 display)
▷DIP S/W : 5 OFF
▷DIP S/W : 6 OFF
ns
※ ON : DOWN / OFF : UP
Default : #8 OFF ▷DIP S/W : 7 ON (display external rear cam)
▷DIP S/W : 8 OFF
io
PIN Function Dip S/W Selection
ON : RGB mode skip
1
ut
Displaying RGB input
OFF : RGB mode display
ON : A/V 1 mode skip
ol
2 Displaying A/V 1
OFF : A/V1 mode display
ON : A/V 2 mode skip
-s
3 Displaying A/V 2
OFF : A/V2 mode display
ON : A/V 3 mode skip
4 Displaying A/V 3
ar
6 N.C
ON : CVBS4
w
8
(not use for user) OFF : DEFAULT
w
※ Please make sure to disconnect the power cable of the interface and reconnect
the power cable again to apply the dip switch setting whenever changing DIP switch.
Otherwise, DIP switch setting will not be applied.
-9-
www.car-solutions.com
3. Settings
3.2 Remote Control
o m
.c
ns
io
ut
ol
Key Function
-s
MENU
▲ Moving upward
w
▼ Moving downward
w
Moving leftward
◀ (If you press this button 2 seconds long, you can access the factory
w
mode.)
Moving rightward
▶ (If you press this button 2 seconds long, you can reset all the
data about user environment.)
-10-
www.car-solutions.com
3. Settings
3.3.1 FACTORY MODE-IMAGE, PARK
FACTORY mode – Press ◀ button 2 seconds long on the remote control.
o m
.c
ns
IMAGE PARK
Adjust navigation position and size
io
PAS TYPE : Selecting Type of parking guide line
- NOT USED : Not use Parking guide line
H-POSITION : Move display horizontally - PAS ON : Selecting Dynamic Parking guide line
V-POSITION : Move display vertically
ut - PAS OFF : Selecting fixed Parking guide line
PDC
-11-
www.car-solutions.com
3. Settings
3.3.1 FACTORY MODE-IMAGE, PARK
PAS SETUP
m
Go to Factory Menu, choose PAS SETUP, by using OK button change
H-POS → V-POS → TYPE
H-POS
o
In H-POSITION, use ◁, ▷ on remote control, to adjust
parking guideline left and right.
.c
ns
io
V-POS
In V-POSITION, use △, ▽on remote control, to adjust
parking guideline up and down.
ut
ol
-s
TYPE
ar
-12-
www.car-solutions.com
3. Settings
3.3.2 FACTORY MODE-UTIL1
FACTORY mode – Press ◀ button 2 seconds long on the remote control.
m
Setup for navigation Setup for car model
o
.c
ns
UTIL1 - CAR MODEL
io
UTIL1 – NAVI MODEL
Definition of the navigation Selecting model of the car
resolution
ut
A4L-NEW
A4L-OLD
DEFAULT : default, 400X234, in low
ol
resolution
LS-901(WQVGA) : 800x480 in high
resolution, for Chinese, Taiwan
-s
-13-
www.car-solutions.com
3. Settings
3.3.2 FACTORY MODE-UTIL1
FACTORY mode – Press ◀ button 2 seconds long on the remote control.
o m
.c
ns
UTIL1 – AVOUT SELECT UTIL1 - FACTORY RESET
Selecting background sound
io
After FACTORY MODE RESET
returning navigation or original
mode
ut
DEFAULT : Selecting AV sound
ol
just before changing
navigation or original mode
from the AV mode
-s
AV source 1~3
.c
w
w
w
-14-
www.car-solutions.com
3. Settings
3.3.3 FACTORY MODE-UTIL2
FACTORY mode – Press ◀ button 2 seconds long on the remote control.
o m
.c
ns
UTIL2 - I_DRV REMOTE UTIL2 - I_DRV CONTROL
Choose DTV and DVD model Selecting whether to use I_DRV
to be control I_DRV function function or not
LI-1DISC
NEC-6DISC
io ON / OFF
ut
USER(when using IR MEMORY) A/V1 : Control DVD Remote control UI
A/V2 : Control DTV Remote control UI
ol
• Select DVD model: Setting on
AV1 Mode
• Select DTV model : Setting on
-s
A/V2 mode
ar
.c
w
DVD(A/V1), DTV(A/V2)
DVD / DTV
-15-
www.car-solutions.com
3. Settings
3.3.3 FACTORY MODE-UTIL2
FACTORY mode – Press ◀ button 2 seconds long on the remote control.
m
UTIL2 – IR MEMORY
o
.c
ns
io
① First of all, press ◀ button on ② Picture above shows DVD remote
remote controller 2 seconds control button value input, select
long or press menu you want to save. (To register
ut
UP→DOWN→UP→MENU button DVD remote control button value,
in order to access Factory select IR MEMORY – DTV and follow
ol
mode. Choose IR MEMORY on below instructions.
UTIL2.
example)
-s
-16-
www.car-solutions.com
3. Settings
3.3.3 FACTORY MODE-UTIL2
FACTORY mode – Press ◀ button 2 seconds long on the remote control.
m
UTIL2 – IR MEMORY
o
.c
ns
③ After register, select “SRC” button
example) continue.. in OSD menu. Then you can see
io
c. When you press device’s confirmation window as shown
remote control button, at the above. At the moment,
same time button value will
ut (If data is saved, DVD TYPE and
appear (see picture above), DTV TYPE will be changed to “USER”
and will turn to green for automatically.)
ol
automatic save.
d. Do these steps to input other If you see “SUCCESS” on screen, the
button value.
-s
FACTORY-UTIL2-I_DRV REMOTE to
“USER”.
.c
※ When touch the middle of the screen, you can control DVD, DTV using
remote control UI via touch screen
w
※ If touch the screen in DVD(A/V1), DTV(A/V2) mode, Can see remote control UI
If touch the screen in RGB, A/V3 mode, Can see mode switching UI
w
- If you want to see mode switching UI in DVD, DTV mode, Select “SRC” button
w
-17-
www.car-solutions.com
3. Settings
3.3.3 FACTORY MODE-UTIL2
FACTORY mode – Press ◀ button 2 seconds long on the remote control.
o m
.c
ns
INFO
io
ut
ol
-s
ar
.c
w
w
w
-18-
www.car-solutions.com
3. Settings
3.4 Original Button Usage
※ User can switch mode using original button in steering wheel
o m
* Press longer : Switching mode(RGB→A/V1~3→Original mode)
.c
* Press shorter : Move to Original mode
ns
io
ut
※ FACTORY MODE→UTIL1→
CAR MODEL→A4L-NEW
ol
-s
※ FACTORY MODE→UTIL1→
w
CAR MODEL→A4L-OLD
w
w
-19-
www.car-solutions.com
3. Settings
3.5 OSD (On Screen Display) / Analog RGB Mode
o m
.c
ns
IMAGE OSD
* BRIGHTNESS *LANGUAGE : Set OSD language
* CONTRAST (only support English and Chinese)
io
* SHARPNESS * TRANS : Adjust OSD transparency
*H-POSITION : Move OSD horizontally
ut
* V-POSITION : Move OSD vertically
ol
-s
ar
.c
UTIL
w
* FACTORY RESET
w
-20-
www.car-solutions.com
3. Settings
3.5 OSD (On Screen Display) / Video Mode
o m
.c
IMAGE OSD
ns
* BRIGHTNESS * LANGUAGE : Set OSD language
* CONTRAST (only support English and Chinese)
io
* SATURATION * TRANS : Adjust OSD transparency
* HUE * H_POSITION : Move OSD horizontally
* SHARPNESS
ut * V_POSITION : Move OSD vertically
ol
-s
ar
.c
UTIL
* FACTORY RESET
w
-21-
www.car-solutions.com
4. Trouble Shooting
Q. I cannot change mode
A. Check connection of Ground cable and IR Cable.
Check LED lamp is on, if not check connection of POWER cable.
m
Q. All I got on the screen is black.
A. .Check second LED lamp of the interface is on, if not, check A/V sources
o
connected are working well.
.c
(Second lamp indicates AV sources connected works well.) Check
interface connection has been done well.
ns
Q. Displayed image color is not proper (too dark or unsuitable color)
A. Try to select “INITIAL” in OSD menu, if it does not work, inform to
manufacturer.
io
Q. I cannot watch the rear camera on the screen
A. Set the DIP switch #7 as state “ON”.
ut
Q. Set mode not appear
A. Check DIP Switch.
ol
Q. OEM image is not displayed.
-s
A. Check interface’s LCD In/Out cable connection. If the status keeps on,
inform to manufacturer.
ar
Q. Show PIP function via handle button, and original screen appear half only.
w
A. This is not because of faulty interface, please check original monitor split
function settings.
w
Q. After connect CAN cable, set gear “P”, video doesn’t appear.
A. Go to “FACTORY MODE”and check “UTIL-Rear Select”. Change
w
-22-
www.car-solutions.com