Beruflich Dokumente
Kultur Dokumente
The V-MAC III Service Software v.2.6.12 effectivity date is 11/15/02. The software
is a fully 32-bit RP1210A-compliant application and will work with MS Windows
95/98/ME, MS Windows NT/2000 & XP (when using an RP1210A-compliant data link
adapter) and both the Kent-Moore J-38351-D and J-45537-PLC serial data link
adapters. NOTE: J-38351-D support under Win NT/2000 & XP uses the adapter in
RP1210A mode (only) and requires the installation of the updated Noregon Standalone
API v.2.5 device drivers. This release of diagnostic software includes support for
all V-MAC III module combinations including E-Tech, CCRS, ASET IEGR, and ASET CEGR
through 1MS364, or V-MAC III Step 9B.
Also included on this CD-ROM are the device drivers necessary to use the Kent-Moore
J-45537-PLC data link adapter with V-MAC III Service Software. They are located in
the ...\J-45537-PLC Drivers v.2.5 directory and supercede the drivers distributed
with the J-45537-MACK essential service tool kit. Note that this version of the
data link adapter drivers will also support the Kent-Moore J-38351-D in RP1210A
mode, and will greatly assist with all reprogramming diagnostics.
NOTE
INSTALLATION:
2. Navigate to your drive, and then the ...\J-45537-PLC Drivers v.2.5 directory.
Run Setup.exe, and follow the onscreen instructions.
3. When running the program for the first time, ensure that you properly select the
data link adapter that you will be using with the software.
May 2, 2002
SD and CDP
----------
CDP
----------
SD
----------
1. Increased the performance of Monitor Parameters and addressed the frequent run-
time errors.
2. Removed the program timing problems that occasionally resulted in screen objects
appearing at the wrong time.
3. Removed Min and Max options from VGT calibration test screens.
4. Restored the "save test results" option to the Run-up test and the Compression
test.
SD and CDP
----------
1. Corrected the variations in screen color observed with Windows 2000 on LCD
screens.
2. ASCII data dictionary (v2.0.0.4) has been updated to provide correct messages for
EDC7 PID/SIDs and FMIs.
Page 2 of 5
CDP
----------
SD
----------
SD and CDP
----------
1. Fixed the time zone calculation problem which caused overflow errors in some time
zones.
2. Added recognition of Step 3 EDC7 (1MS368).
3. Replaced the series of confusing startup messages with a single, more user-
friendly one.
CDP
----------
1. Removed Driveshaft Speed Limit Lower RPM from View/Print Current Parameters (the
parameter is not programmable).
SD
----------
1. Now properly disables features with Cummins engines that are not applicable.
2. Restored the indicator in the fault displays that shows which faults are recorded
in the Fault Reporter.
Page 3 of 5
July 2, 2002
CDP
----------
SD and CDP
----------
CDP
----------
1. Added the option to enable the MACK Power Leash engine brake.
2. Corrected a problem which caused incorrect programming history records to be
written to the VECU.
3. Removed the unused option "Reset Oil Change via Electronic Dash" in Fleet Display
and Trip Parameters.
SD
----------
September 6, 2002
Page 4 of 5
SD
----------
CDP
----------
1. Maintenance broadcast and blackout times are correctly displayed in local time
(not in GMT).
2. Option to enable Power Leash brake is now available.
SD
----------
1. Times displayed in the Monitor Parameters option and in the Fault Reporter are
now correctly shown in local time (not in GMT).
2. Corrected a run-time overflow error that can occur when an invalid date is read
from the VECU during the Maintenance Data Log Display.
3. The mouse pointer now changes to an hourglass while reading data for the All
Active Faults display, because this process can take several seconds.
4. Corrected timing and display problems that can occur when enabling or disabling
the POC option.
SD and CDP
----------
1. Fixes a runtime error problem (subscript out of range) that has been seen with
specific EECU data files, in which the software ID has been defined in a non-
standard way. The problem is known to exist with V-MAC III Step 4 EECUs with a
1MS571P13 data file.
Page 5 of 5