Sie sind auf Seite 1von 13

OPERATION MANUAL

MONO-PHASE MULTI TARIFF-DEMANDMETER


ACTIVE
ELECTRONIC ELECTRICITY METER

MODEL VEM-M580DB0
MODEL VEM-M580DB2

1
CONTENTS

GENERAL INFORMATION AND WARNINGS …..……………………………………...3


TYPE CODE TABLE.......…………………….……………………..……………………....3
GENERAL FEATURES..................................... ………………..…………….…………....4
TABLE OF PRODUCT SPECIFICATIONS.......…………………...……………………....4
FUNCTIONS.........…………………………………………………………….………….…5
INSTALLATION INSTRUCTIONS.........………………………………………………….6
CONNECTION DIAGRAMS.........………………………………………….…….………..6
DISPLAY SYMBOLS.………………………………………………………………………7
DISPLAY INFORMATION……………………………………………………..………….8
SUB-MENU INFORMATION.........…………………………………………….............9-10
ERROR WARNING DISPLAYS...…………………………………………...…………....11
COMPANY AND TECHNICAL SERVICE INFORMATION...……………………….…12

2
GENERAL INFORMATION AND WARNINGS

This manual provides information regarding the specifications, installation and operation of the
VIKO BRAND, VEM-M series Electronic Electricity Meters.

 PLEASE READ THIS MANUAL CAREFULLY BEFORE ATTEMPTING TO INSTALL


OR OPERATE THE METER!
 THE INSTALLATION OF THE METER MUST BE PERFORMED BY QUALIFIED
PERSONNEL, IN ACCORDANCE WITH THE METER’S OPERATIONAL
INFORMATION.
 POWER LINES MUST BE DISCONNECTED DURING THE INSTALLATION AND
DISASSEMBLY OF THE METER.
 COMING INTO CONTACT WITH PARTS THAT ARE CHARGED WITH VOLTAGES
POSE LETHAL RISK.
 THE METER MUST BE OPERATED IN ENVIRONMENTS HAVING
TEMPERATURES, ELECTROMAGNETIC AND MECHANICAL BETWEEN THE
VALUES SPECIFIED WITHIN THIS MANUAL.
 THE EXTERIOR SURFACE OF THE METER SHOLD NOT BE CLEANED USING
ABRASIVE MATERIALS.
 THE CALIBRATION AND PROGRAMMING OF THE METER IS CARRIED OUT
DURING THE PRODUCTION PHASE AND EACH METER IS OFFERED AFTER
CONDUCTING QUALITY CONTROLS. THERE ARE NO MAINTENANCE OR
PROGRAMMING ACTIVITIES THAT MAY BE CONDUCTED BY THE USERS.

This manual is the property of Viko, and it may not be copied, reproduced, or lent to third parties.
All information contained herein is current information at the time of printing. VIKO reserves the
right to make changes without prior notification.

Scope of the Guarantee


Our meters are guaranteed against production flaws for a period of five (5) years. The damages that
may arise due to installation and operation of the meters that are not in accordance with the
information stated in this manual are excluded from the scope of the guarantee.
Servicing or maintenance may only be performed by VIKO’s authorized technical service
personnel or other persons or organizations that are authorized by VIKO. The damages that may
arise due to the servicing or maintenance performed by unauthorized persons renders the guarantee
void.
VIKO BRAND, VEM-M series Electronic Electricity Meters are designed and produced in
accordance with the most current international standards applicable in Turkey. The meters are
designed to provide precise readings, with the help of high-tech components for flawless operation
over long periods of time in accordance with the most current international standards to provide
ease of use while possessing physical qualities that are able to satisfy site requirements.

The meter satisfies the following standards:


EN 50470-1
EN 50470-3
EN 62054-21
EN 62056-21

3
METER TYPE CODE TABLE

PRODUCT TYPE OF MEASUREMENT COMMUNICATION


CODE MEASUREMENT CURRENT TYPE OF CONNECTION CLASS OUTPUT TYPE

VEM - X XXXXX X X X X
NULL
VIKO ENERGY CHARACTER
METERING M = MONOPHASE 1080 D = DIRECT CONNECTION A= CLASS A 0= NOT NORMAL
P= WITH
C = WITH CURRENT ADVANCE
T = THREEPHASE 10100 TRANSFORMER B= CLASS B 1= RS232 PAYMENT
V = WITH
CURRENT/VOLTAGE
C = COMBI x5 TRANSFORMER C= CLASS C 2= RS485
1060 3= PLC
5(80)
5(100)

General Features
 Active energy measurement
 Active demand measurement
 Has a timer and calendar that may operate during power outages. In the event of an error in
the timer, the error is detected automatically and the index is recorded in the T1 tariff for all
tariff timers.
 Automatic daylight saving adjustments in accordance with the EU norms in force
 Technical hardware that allows for canceling the application of daylight savings or makes it
possible to alter the times.
 Storage of the data belonging to the previous year.
 8 time zones and 4 tariffs, the tariffs may be altered without having to remove the meter
from where it is placed.
 Communication through an optical port
 Large LCD display for ease of reading
 Availability of information from the optical port and LCD display even if there is a power
outage.
 Ability to view the electric terminal cover and top cover’s (open/closed) positions on the
LCD display
 Critical battery level warning
 Timer error warning
 60 day demand profile
 Ability to set the index information displayed on the LCD display in 5 integers and 3
decimals, 6 integers and 2 decimals or 7 integers and 1 decimal.

THE FOLLLOWING INFORMATION ARE DISPLAYED IN THE SUB-MENU THAT CAN


BE ACCESSED BY PRESSING AND HOLDING DOWN THE METER READING
BUTTON.
 Displaying of the index information of the previous month on the LCD display
 Displaying of the voltage values on the LCD display
 Displaying of the current values on the LCD display
 Displaying of the power factor values on the LCD display
 Displaying of the network frequency on the LCD display
 Displaying of the momentary power on the display

4
TABLE OF PRODUCT TECHNICAL SPECIFICATIONS

CURRENT CIRCUIT
MODEL VEM-M580DB0 VEM-M1080DB0 POWER < 2 W 10 VA
CONSUMPTION
VOLTAGE CIRCUIT
OPERATING VOLTAGE 230 V 230 V POWER <4VA
CONSUMPTION
MINIMUM CURRENT FOR
TIMER BATTERY
CORRECT 0.25 A 0,5 A 3,6 V
VOLTAGE
MEASUREMENT
CURRENT FOR STARTING READING BATTERY
0.02 A 0.04 A 3,6 V
MEASUREMENT VOLTAGE
REFERENCE CURRENT 5A 10 A BATTERY CAPACITY 1,2 Ah
MAXIMUM CURRENT 80A 80A BATTERY LIFE 10 YEARS
3200 3200
CONSTANT TIMER PRECISION <0,5 Sec./DAY
imp/kWh imp/kWh
CLASS OF ERROR B B NUMBER OF TARIFFS 4 Energy tariffs
NUMBER OF
FREQUENCY 50 Hz 50 Hz 8 time zones
TIMEZONES
LCD life 10
IP54 IP54 DISPLAY
ISOLATION CLASS years
RELATIVE RATE OF
95% 95% DIMENSIONS 45x190x123
HUMIDITY
-40 C° / -40 C° /
TEMPERATURE RANGE WEIGHT 417 gr.
+70 C° +70 C°
CLASS OF EMC E2 E2
CLASS OF ENVIRONMENT M1 M1

5
HOLDING PART : They are used during the installation of the meter. The position of the part
of the meter can be adjusted vertically with the help of the adjustment screws found on the back of
the meter.

LCD DISPLAY : It displays the information gathered by the meter.

OPTICAL PORT : It is a communication unit that enables communication between the meter
and a hand held terminal or computer for the programming of permitted parameters or for the
reading of the information gathered by the meter.

READING BUTTON : It is the button that successively updates the information gathered by the
meter on the LCD display. If the meter button is not pressed, the display information will be
updated automatically every 5 seconds and displayed on the screen. The automatic screen will start
to operate 30 seconds after a reading has been conducted using the button.

TOP COVER SEAL: It is a seal affixed after the production, quality control and calibration
procedures of the meter have been conducted. Due to the fact that legal action may be taken
against unauthorized persons that tamper with these seals, the seals shall not be removed or
damaged.

TERMINAL COVER SEAL: It is an area where the distribution company must affix their seals in
order to prevent unauthorized access to the electric terminal block where the meter connections are
made. Due to the fact that legal action may be taken against persons that have not been
authorized by the distribution company but tamper with the electric terminal seals, the seals
shall not be removed or damaged

TERMINAL COVER : It is the part which covers the area where the meters’ connections are made.
In the event that the covers are opened, the information at the time of opening of the covers is
recorded in the device’s memory. After installation, power is supplied after the covers have been
closed. There is a part underneath that may be broken off for the cables to be inserted.

6
Figure 1 Figure 2

INSTALLATION OF THE METER AND ITS SEALS

The meter is installed by the help of the installation part located on the top of the device and the
three installation holes found on either bottom side of the device. The dimensions of the device
are shown in figure 1, and the installation holes are shown in figure 2.

The VEM-M series electronic electricity meters are protected against unauthorized use with the
help of a total of 3 seals of which 2 are calibration seals and 1 is an electric terminal cover seal.

INSTALLATION INSTRUCTIONS
1- Install the meter using the installation holes as shown in figure 2.
2- Make the phase and neutral connections in accordance with the connection diagram.
(While the connections are being made, make sure that the tips of the cables are properly
stripped, that the connection screws in the electric terminal are tightened in a way that
does not damage the conductor, and that no faulty connections are made.)
3- Before applying voltage, make sure that the electric terminal cover and the electric
terminal cover button are closed.
4- Apply voltage and current. In the event that the meter is connected in reverse, a flashing
arrow ( ) symbol will appear. When this happens, control the meter’s connections
after you have disconnected the power.

CONNECTION DIAGRAM OF AN MF METER

DISPLAY SYMBOLS

7
DISPLAY SYMBOLS

Timer error warning

Lights up when information related to date is displayed on the LCD screen.

Lights up when information related to time is displayed on the LCD screen.

Battery warning

The section where OBIS codes of the information displayed on the meter screen is shown.

The numerator where the information contained in the meter is displayed.

The section that indicates which tariff information belongs to the tariffs.

Indicates the tariff that the meter keeps records in.

Appears and flashes on screen when the meter’s connections have not been made
properly. When this icon appears, the connections of the meter have to be checked.

Indicates that the information displayed on the screen is related to demand.

Indicates the measurement units of the information displayed.

Electric terminal cover opening warning.

Top cover opening warning.

8
DISPLAY INFORMATION

DATE

TIME

TOTAL ACTIVE ENERGY

TARIFF 1
ACTIVE ENERGY

TARIFF 2
ACTIVE ENERGY

TARIFF 3
ACTIVE ENERGY

TARIFF 4
ACTIVE ENERGY

CURRENT PERIOD (MONTH) ACTIVE ENERGY


P-MAX VALUE

DATE OF INFORMATION OF
ACTIVE ENERGY PMAX

9
TIME OF INFORMATION OF
ACTIVE ENERGY PMAX

SUB-MENU INFORMATION
The sub-menu can be accessed by pressing and holding down the meter reading button for 5
seconds. The latest demand reset information and the operational information regarding the
network that the meter is connected to are displayed in the sub-menu.

SERIAL NUMBER

PREVIOUS PERIOD TOTAL


ACTIVE ENERGY

PREVIOUS PERIOD TARIFF 1 TOTAL


ACTIVE ENERGY

PREVIOUS PERIOD TARIFF 2 TOTAL


ACTIVE ENERGY

PREVIOUS PERIOD TARIFF 3 TOTAL


ACTIVE ENERGY

PREVIOUS PERIOD TARIFF 4 TOTAL


ACTIVE ENERGY

PREVIOUS PERIOD (MONTH) ACTIVE ENERGY


P-MAX VALUE

PREVIOUS PERIOD
DATE OF INFORMATION OF
ACTIVE ENERGY PMAX

PREVIOUS PERIOD
10
TIME OF INFORMATION OF
ACTIVE ENERGY PMAX

DATE OF THE OPENING


TERMINAL COVER

TIME OF THE OPENING


TERMINAL COVER

NUMBER OF TIMES THE


TERMINAL COVER HAS BEEN OPENED

THE VOLTAGE OF THE NETWORK


THAT THE METER IS CONNECTED TO

CURRENT PASSING OVER THE METER

POWER PASSING OVER THE METER

THE FREQUENCY OF THE NETWORK THAT


THE METER IS CONNECTED TO

11
ERROR WARNING DISPLAYS

Terminal cover opening warning:

The meter is designed to detect and record instances when the cover used for covering the terminal
section that the connections are made is opened. For the meter not to keep records of any opening
of the covers during the initial installation of the meter, the cover opening records are not kept until
the meter records indexes. However, a warning flashes to indicate the opening of the electric
terminal covers. If the index that is required for keeping record has not passed through the meter,
the warning on the screen disappears after the covers are closed. In order for records to be kept after
the meter is installed, the electric terminal covers must be closed, and the necessary index must be
passed through the meter. If the recording of the opening of covers is activated, the meter, records
the date and time of the first opening of the covers in each month and counts, records, and stores the
number of times they have been opened during the month. This information may be accessed in the
meters’ sub-menus. During the passage to the next month, it stores the current information in its
memory as the previous month’s information and resets the information for the next month. It keeps
recording the openings of the covers in the next month as described above. If a month passes with
the cover of the device open, it records the date of the passing of the month as the initial opening of
the covers, but indicates the number of openings as ‘’0’’.
It is possible to delete the electric terminal cover opening warning through conducting optical
readings from the meter. Optical readings only delete the warning on the device display, the stored
memory regarding the openings are not erased. .

Top cover opening warning:

The device is designed to detect, record and store the date and time of the opening of the cover that
covers the section where the measurement section is located. The top cover should not be
tampered with, as the opening of the top cover which has been sealed will be regarded as attempting
illegal use. When the cover is opened, a flashing warning for the opening of the top cover will be
displayed on the screen. The date and time of the opening of the top cover will be recorded and
stored in memory. Only the first opening of the covers will be recorded, and subsequent openings
will be ignored. It is only possible to reset the warning for the opening of the top cover by
authorized personnel in the factory environment.

Battery warning:

Appears on the screen when the battery supplying power to the meter’s timer is at a critical level.
Due to the fact that the battery is placed underneath the top cover, it must be replaced by authorized
service personnel. Contact our technical service in the event that a warning is displayed.

12
Timer error warning:

Appears on the screen when there is an error associated with the timer. In this case, the meter’s
tariff function is disabled and it records the whole index as a T1 tariff. Please contact our technical
service in the event that a timer error warning is displayed.

COMPANY DETAILS
VIKO Elektrik ve Elektronik Endustrisi San.ve Tic. A.S.

ADDRESS: Abdurrahmangazi Mah. Ebubekir Cad. No:44


34887 Sancaktepe-Samandira / Istanbul

Tel : 0 216 564 55 55


Fax: 0 216 564 55 05
Web: www.vikosayac.com

TECHNICAL SERVICE ADDRESS


Abdurrahmangazi Mah. Ebubekir Cad. No:44
34887 Sancaktepe-Samandira / Istanbul
Tel : 0 216 564 55 55
Fax: 0 216 564 55 66

13

Das könnte Ihnen auch gefallen