Sie sind auf Seite 1von 43

Volkswagen Golf 5 - Electromechanical steering gear, servicing (Generation I) Стр.

1 из 43

48 - 7

Electromechanical steering gear, servicing


(Generation I)

„ Steering gear housing

„ Left tie rod

„ If faulty, replace with tie rod


end

„ Tightening torque Topic


48-3

„ Removing and installing


48-7, Tie rod, removing and
installing

„ Left tie rod end


Electromechanical steering gear, servicing (Generation I) Стр. 2 из 43

„ Check dust caps for damage


and correct seating

„ Nut

„ Tightening torque Topic


48-3

„ Nut must be counterheld on


tie rod end using a wrench
when loosening and
tightening.

„ Spring clamp

„ Boot

„ Removing and installing


48-7, Boot, removing and
installing

„ Check for damage

„ Must not be twisted after toe


is adjusted

„ Clamp

„ Always replace after


removal

„ Install new clamp using


locking pliers VAS 6199

„ Gasket

„ Between steering gear and


vehicle interior

„ Bolt

„ Tightening torque Topic


48-3

„ For mounting cap Item -


10 - to steering gear housing
Item - 1 -

„ 4 bolts
Electromechanical steering gear, servicing (Generation I) Стр. 3 из 43

„ Cover

„ Gasket

„ Always replace

„ Steering pinion with steering


torque sensor

„ With Steering Torque Sensor


G269

„ Cannot be replaced
separately

„ Sensor wire

„ Removing and installing


48-7, Sensor wire,
replacing

„ Electrical connection
between Steering Torque
Sensor G269 and Power
Steering Control Module
J500

„ Right tie rod end

„ Check dust caps for damage


and correct seating

„ Bolt

„ Tightening torque Topic


48-3

„ For mounting servo motor to


control module Item - 20 -
on steering gear housing
Item - 1 -

„ Clamp with nuts

„ Replace if there is damage


in thread

„ Rubber bushing

„ Bracket
Electromechanical steering gear, servicing (Generation I) Стр. 4 из 43

„ Sealing ring

„ Always replace

„ Servo motor with control module

„ Removing and installing


48-7, Servo motor with
control module, removing
and installing

„ With Power Steering Control


Module J500

„ With Electromechanical
Power Steering Motor V187

„ With Engine Speed (RPM)


Sensor G28

„ Can be tested in "Guided


Fault Finding" using Vehicle
Diagnosis, Testing and
Information system VAS
5051B

„ Clip

„ Contact foil

„ Not an individual part, is


installed on hydraulic thrust
piece Item - 23 -

„ Coat with supplied grease G


052 192 A1 on contact side
facing steering rack

„ Hydraulic thrust piece

„ Removing and installing


48-7, Hydraulic thrust piece,
replacing and adjusting

„ Sealing ring

„ Installed on hydraulic thrust


piece Item - 23 -

„ Sealing ring
Electromechanical steering gear, servicing (Generation I) Стр. 5 из 43

„ Insert into steering gear


housing between thrust
piece and adjustment screw

„ Adjustment bolt

„ For hydraulic thrust piece


Item - 23 -

„ Always replace

„ Rubber plug

„ Adjustment bolt

„ For mechanical thrust piece


Item - 31 -

„ Always replace

„ Spring

„ Sealing ring

„ Installed on mechanical
thrust piece Item - 31 -

„ Mechanical thrust piece

„ Removing and installing


48-7, Thrust piece on
steering pinion side,
replacing and adjusting

„ Contact foil

„ Not an individual part, is


installed on mechanical
thrust piece Item - 31 -

„ Coat with supplied grease G


052 192 A1 on contact side
facing steering rack

„ Hex nut

„ Always replace after


removal

„ Torque specifications 48-


Electromechanical steering gear, servicing (Generation I) Стр. 6 из 43

3, Steering, torque
specifications

„ Screw plug

„ Fill with grease G 052 192


A1 before installing

„ Coat thread with LOCTITE


5910

„ Torque specifications 48-


3, Steering, torque
specifications

Boot, removing and installing

Special tools, testers and auxiliary items required

„ Locking pliers VAS 6199

„ Torque wrench V.A.G 1332


Electromechanical steering gear, servicing (Generation I) Стр. 7 из 43

„ Hose clamp pliers V.A.G 1275

Removing

Note:

„ If boot is faulty, moisture and dirt penetrates into


steering gear. There must be a noticeable grease
film present on steering rack in area of splines. If
grease film is not present, steering gear must be
replaced. Steering gear must also be replaced if
there is corrosion or steering gear is damaged or
worn out.

- Turn steering wheel into straight ahead position.

- Remove wheel.

- Clean outside of steering gear in area of boot.

While doing this, no dirt must enter the steering gear


through the faulty boot.

- Mark position of nut - 3 - on tie rod.

- Loosen nut - 3 - , while doing this, counterhold on tie rod


end - 2 - .
Electromechanical steering gear, servicing (Generation I) Стр. 8 из 43

- Loosen spring clamp - 1 - using hose clamp pliers V.A.G


1275 from boot and slide on to tie rod.

- Remove clamp and pull off boot from steering gear


housing.

- Twist tie rod out of tie rod end.

- Pull off boot with spring clamp from tie rod.

Note:

„ If corrosion, damage, wear-out or first signs of


soiling on steering rack can be seen, complete
steering gear must be replaced.

„ If no grease film is visible on steering rack, steering


gear must also be replaced completely.

Installing

Before installing, steering rack must be coated with grease


G 052 192 A1 supplied in repair kit.

Caution!

Do not use other grease under any circumstances.

For this purpose, turn steering to stop toward both sides in


succession.

For clearer illustration, steering gear has been removed in


the illustration.

- Grease steering rack on toothed side - A - and on thrust


piece side with grease G 052 192 A1 .

- Turn steering wheel into straight ahead position.

- Guide new clamp and boot on to tie rod.


Electromechanical steering gear, servicing (Generation I) Стр. 9 из 43

- Screw in tie rod until marking applied during removal is


reached.

- Tighten lock nut - 3 - to tightening torque, while doing


this, counterhold on tie rod end - 2 - .

- Slide boot - 2 - on to tie rod - 1 - as depicted in


illustration.

- Secure spring clamp on boot using hose clamp pliers


V.A.G 1275 .

- Slide boot on to steering gear housing.

- Tighten new clamp using locking pliers VAS 6199 to the


extent depicted in the illustration.
Electromechanical steering gear, servicing (Generation I) Стр. 10 из 43

Installation is in reverse order of removal.

Tightening torques 48-3, Steering, torque


specifications .

After installation the vehicle must be measured.

- Perform vehicle alignment 44-6, Wheel alignment .

- Perform basic setting for Steering Angle Sensor G85 via


Vehicle Diagnosis, Testing and Information System VAS
5051B , "Guided Fault Finding" .

- Perform basic setting of steering system via Vehicle


Diagnosis, Testing and Information System VAS
5051B "Guided Fault Finding" .

Tie rod, removing and installing

Special tools, testers and auxiliary items


required

„ Ball joint puller 3287 A


Electromechanical steering gear, servicing (Generation I) Стр. 11 из 43

„ Hose clamp pliers V.A.G 1275

„ Torque wrench V.A.G 1332

„ 38 mm open end wrench insert


V.A.G 1923

„ Locking pliers VAS 6199

Removing tie rod

- Turn steering wheel into straight ahead position.

- Clean outside of steering gear in area of boot.

Loosen nut - 3 - , while doing this, counterhold on tie rod


end - 2 - .

- Remove front wheel.

- Loosen tie rod end nut, but do not remove yet.

To protect ball joint thread, screw nut on a few turns to


pin.
Electromechanical steering gear, servicing (Generation I) Стр. 12 из 43

- Press tie rod end off wheel bearing housing using ball
joint puller 3287 A and remove nut.

- Loosen spring clamp (item - 1 - in illustration N44-10005


Topic 48-7 ) using hose clamp pliers V.A.G 1275 from
boot and slide on to tie rod.

- Remove clamp and pull off boot from steering gear


housing.

- Remove tie rod from steering gear using 38 mm open


end wrench insert V.A.G 1923 .

Note:

„ If corrosion, damage, wear-out or first signs of


soiling on steering rack can be seen, complete
steering gear must be replaced.

„ If no grease film is visible on steering rack, steering


gear must also be replaced completely.

Installing tie rod

Before installing, steering rack must be coated with grease


G 052 192 A1 supplied in repair kit.
Electromechanical steering gear, servicing (Generation I) Стр. 13 из 43

Caution!

Do not use other grease under any circumstances.

For this purpose, turn steering to stop toward both sides in


succession.

For clearer illustration, steering gear has been removed in


the illustration.

- Grease steering rack on toothed side - A - and on thrust


piece side with grease G 052 192 A1 .

- Turn steering wheel into straight ahead position.

- Twist tie rod far enough into tie rod end until dimension -
a - is obtained.

Dimension - a - = 371 1 mm

- Guide new clamp and boot on to tie rod.

- Rotate tie rod in steering rack and tighten.


Electromechanical steering gear, servicing (Generation I) Стр. 14 из 43

- Slide boot - 2 - on to tie rod - 1 - , when doing this, pay


attention to correct position.

- Slide boot on to steering gear housing until it stops.

- Tighten new clamp using locking pliers VAS 6199 to


extent depicted in illustration.

Installation is in reverse order of removal.

Tightening torques of steering 48-3, Steering, torque


specifications .

Tightening torque for wheel mounting 44-2, Torque


specification for wheel bolts .

After installation the vehicle must be measured.

- Perform vehicle alignment 44-6, Wheel alignment .

- Perform basic setting for Steering Angle Sensor G85 via


Vehicle Diagnosis, Testing and Information System VAS
5051B , "Guided Fault Finding" .

- Perform basic setting of steering system via Vehicle


Diagnosis, Testing and Information System VAS
5051B "Guided Fault Finding" .

Sensor wire, replacing


Electromechanical steering gear, servicing (Generation I) Стр. 15 из 43

Special tools, testers and auxiliary items


required

„ Holding fixture VW 313

„ Thrust piece 3253/6 qty. 2

„ Torque wrench V.A.G 1331

„ Locking pliers VAS 6199

„ Transmission support T10108

„ Adapter T10304

„ 2 bolts M10 x 60
Electromechanical steering gear, servicing (Generation I) Стр. 16 из 43

Removing

- Steering gear, removing 48-5, Steering gear, removing


and installing .

- Tension steering gear using 2 bolts M10 x 60 as depicted


in the illustration.

- Clean steering gear in area of cover.

- Remove clamp for boot at left - 1 - and pull off boot from
steering gear housing.

- Turn steering into straight ahead position using


T10304 .

For this purpose, dimension - a - = 28 mm.

- Disengage sensor wiring at steering gear housing.


Electromechanical steering gear, servicing (Generation I) Стр. 17 из 43

- Remove seal - 1 - from cover - 2 - .

- Remove cover - 2 - .

- Carefully lift seal from steering gear housing.

No seal remnants must enter sensor or housing.

Prevent contact with electrical components - arrow - !

- Observe general repair notes 48-2, Electrical


components .

Caution!

During longer interruptions of work, cover the opened


steering gear housing with e.g. foil to protect against
moisture.
Electromechanical steering gear, servicing (Generation I) Стр. 18 из 43

- Disconnect connector from wiring harness and set aside.

It is needed to code new sensor wiring. Connector housing


is not installed on new sensor wiring.

Note:

„ A locking mechanism - arrow - for steering pinion


spiral spring is located on sensor wire in steering
gear housing. When removing sensor wire, make
sure that spiral spring is twisted only as far until
connector can be removed (twist a maximum of 30
).

- Disconnect harness connector of sensor wire at steering


Electromechanical steering gear, servicing (Generation I) Стр. 19 из 43

pinion.

To do so, press connector terminal out of spiral spring


housing using a screwdriver (3 mm blade width) as
depicted in the illustration.

- Remove locking mechanism from steering gear housing.

- Remove sensor wiring from steering gear housing.

Installing

- Guide sensor wiring into steering gear housing.

- Lock spiral spring - arrow - at steering gear housing with


sensor wiring.

- Place connector in spiral spring housing.

Connector terminal is coded and fits only in one direction.

- Disconnect old connections to control module.

- To do so, press button - A - in direction of - arrow - and


then disconnect connector.

- Insert new sensor wiring wires into new connector


housing.

- Use old connector as a template for coding.


Electromechanical steering gear, servicing (Generation I) Стр. 20 из 43

- Engage adapter - 2 - to connector housing - 3 - .

- Engage sensor wiring to steering gear housing - 1 - .

Pay attention to wire routing.

- Connect connector with control module.

- Fill intermediate area above shaft oil seal in cover -


arrow - completely with grease G 052 192 A1 supplied.

Caution!

Do not use other grease under any circumstances.

- Install cover with new seal.

- Remove excess grease on cover of steering pinion and


on steering pinion.

Installation is in reverse order of removal.

Tightening torques 48-3, Steering, torque


Electromechanical steering gear, servicing (Generation I) Стр. 21 из 43

specifications .

- Steering gear, installing 48-5, Steering gear, removing


and installing .

- Perform vehicle alignment 44-6, Wheel alignment .

- Perform basic setting for Steering Angle Sensor G85 via


Vehicle Diagnosis, Testing and Information System VAS
5051B , "Guided Fault Finding" .

- Perform basic setting of steering system via Vehicle


Diagnosis, Testing and Information System VAS
5051B "Guided Fault Finding" .

Hydraulic thrust piece, replacing and adjusting

Special tools, testers and auxiliary items


required

„ Holding fixture VW 313


Electromechanical steering gear, servicing (Generation I) Стр. 22 из 43

„ Thrust piece 3253/6 qty. 2

„ Torque wrench V.A.G 1331

„ Locking pliers VAS 6199

„ Transmission support T10108

„ Adapter T10304

Special tools, testers and auxiliary items required

„ Friction meter VAS 6222

„ Adapter T10305

Other required special tools and equipment not


depicted

Special tools, testers and auxiliary items required


Electromechanical steering gear, servicing (Generation I) Стр. 23 из 43

„ Wet and dry vacuum cleaner for example V.A.G


1373

„ Cordless drill for example VAS 5036

„ Spiral bore dia. 4 mm

„ 2 bolts M10 x 60

Removing

- Steering gear, removing 48-5, Steering gear, removing


and installing .

- Clean steering gear in area of adjustment screw.

- Tension steering gear using 2 bolts M10 x 60 as depicted


in the illustration.

- Determine starting torque of steering.

- First turn steering toward right in direction of travel until it


stops.

- Turn steering uniformly toward left until it stops on friction


Electromechanical steering gear, servicing (Generation I) Стр. 24 из 43

meter, e.g. VAS 6222 . Read off steering torque while


doing this.

Specification: 3 2 Nm

1 - Friction meter, e.g. VAS 6222


2 - 24 mm socket

- Remove clamp for boot at left - 1 - and pull off boot from
steering gear housing.

- Turn steering into straight ahead position using


T10304 .

For this purpose, dimension - a - = 28 mm.

- Rotate steering gear in mounting bracket so that thrust


piece with adjustment screw points upward.

- Now slide boot onto steering gear cover again.

- Drill out the 6 peenings using a dia. 4 mm drill bit until


Electromechanical steering gear, servicing (Generation I) Стр. 25 из 43

dimension - a - has been reached.

Dimension - a - = 3 mm

Do not drill deeper than 3 mm.

- Vacuum up drill shavings completely from steering gear


housing using e.g. wet and dry vacuum cleaner V.A.G
1373 .

- Remove adjustment screw.

- Remove sealing ring - arrow - .

- Pull steering rack in direction of thrust piece so that it


disengages from steering rack.
Electromechanical steering gear, servicing (Generation I) Стр. 26 из 43

- Simultaneously pull out hydraulic thrust piece from


steering gear housing using suitable pliers.

Note:

„ If corrosion, damage, wear-out or first signs of


soiling on steering rack can be seen, complete
steering gear must be replaced.

„ If no grease film is visible on steering rack, steering


gear must also be replaced completely.

Installing and adjusting

- Coat new thrust piece (contact surface at steering gear),


sealing ring and hole in steering gear housing with grease
G 052 192 A1 supplied - arrows - .

Caution!

Do not use other grease under any circumstances.


Electromechanical steering gear, servicing (Generation I) Стр. 27 из 43

- Install hydraulic thrust piece and sealing ring - arrow -


by hand.

- Tighten new adjustment screw to 40 Nm.

- Peen the adjustment screw 6 times - arrows - using a


punch.

Punch points must be applied 2 graduation lines next to the


drill out punch points.
Electromechanical steering gear, servicing (Generation I) Стр. 28 из 43

- Mark one graduation line of adjustment screw on the


steering gear housing - 1 - .

- Remove adjustment screw 5.5 graduation lines toward


left - 2 - .

While doing this, a loosening torque of at least 15 Nm must


be obtained.

If loosening torque is not obtained:

- Tighten adjustment screw to 40 Nm again.

- Reinforce the 6 peenings using a punch.

- Check applied marking of adjustment screw graduation


line on steering gear housing, re-apply marking if
necessary.

- Remove adjustment screw 5.5 graduation lines toward


left.

A loosening torque of at least 15 Nm must be obtained.

- Turn steering using T10304 from left stop to right stop.

No hitching or jamming may occur while steering through.


If the surface of steering rack is damaged and steering
gear must be replaced.
Electromechanical steering gear, servicing (Generation I) Стр. 29 из 43

- Install left boot on to steering gear housing with new


clamp.

- Determine starting torque of steering.

- First turn steering toward right in direction of travel until it


stops.

- Turn steering uniformly toward left until it stops on friction


meter, e.g. VAS 6222 . While doing this, read off steering
torque .

Specification: 3 2 Nm

1 - Friction meter, e.g. VAS 6222


2 - 24 mm socket

If steering torque is exceeded:

- Remove adjustment screws for hydraulic thrust piece


about one graduation line (turn adjustment screws toward
left).

- Check steering torque Topic 48-7 .

If steering torque falls short:

- Screw in adjustment screws for hydraulic thrust piece


about one graduation line (turn adjustment screws toward
right).

- Then, check steering torque Topic 48-7 .

- Steering gear, installing 48-5, Steering gear,


installing .

- Perform vehicle alignment 44-6, Wheel alignment .

- Perform basic setting for Steering Angle Sensor G85 via


Vehicle Diagnosis, Testing and Information System VAS
5051B , "Guided Fault Finding" .
Electromechanical steering gear, servicing (Generation I) Стр. 30 из 43

- Perform basic setting of steering system via Vehicle


Diagnosis, Testing and Information System VAS
5051B "Guided Fault Finding" .

Thrust piece on steering pinion side, replacing and


adjusting

Special tools, testers and auxiliary items


required

„ Holding fixture VW 313

„ Thrust piece 3253/6 qty. 2

„ Torque wrench V.A.G 1331

„ Locking pliers VAS 6199

„ Transmission support T10108


Electromechanical steering gear, servicing (Generation I) Стр. 31 из 43

„ Adapter T10304

Special tools, testers and auxiliary items


required

„ Universal dial gauge VW 387

„ 38 mm open end wrench insert


V.A.G 1923

„ Adapter VAS 3313

„ Friction meter VAS 6222


Electromechanical steering gear, servicing (Generation I) Стр. 32 из 43

Other required special tools not depicted

Wet and dry vacuum cleaner for example V.A.G 1373

Cordless drill for example VAS 5036

Spiral bore dia. 4 mm

Pliers for outer securing rings, for example HAZET 1847-


2

Dial gauge

2 bolts M10 x 80

Removing

- Steering gear, removing 48-5, Steering gear, removing


and installing .

- Clean steering gear in mechanical thrust piece


adjustment screw area and steering pinion cover.

- Tension steering gear using 2 bolts M10 x 80 as depicted


in the illustration.

- Determine steering starting torque.

- First turn steering toward right in direction of travel until it


stops.
Electromechanical steering gear, servicing (Generation I) Стр. 33 из 43

- Turn steering uniformly toward left until it stops on friction


meter, e.g. VAS 6222 . Read off steering torque.

Specification: 3 2 Nm

1 - Friction meter, e.g. VAS 6222


2 - 24 mm socket

- Remove clamp for boot at left - 1 - and pull off boot from
steering gear housing.

- Turn steering into straight ahead position using


T10304 .

For this purpose, dimension - a - = 28 mm.

- Slide boot - 1 - without clamp back on to steering gear


housing.

- Rotate steering gear in mounting bracket so that thrust


piece with adjustment screw points upward.

- Slide boot onto steering gear cover again.


Electromechanical steering gear, servicing (Generation I) Стр. 34 из 43

- Drill out 6 peenings using a dia. 4 mm drill bit until


dimension - a - has been reached.

Dimension - a - = 3 mm

Do not drill deeper than 3 mm.

- Vacuum up drill shavings completely from steering gear


housing using e.g. wet and dry vacuum cleaner V.A.G
1373 .

- Remove adjustment screw.

- Remove spring and sealing ring - arrow - .


Electromechanical steering gear, servicing (Generation I) Стр. 35 из 43

- Remove thrust piece from steering gear housing, e.g.


with HAZET 1847-2 .

Note:

„ If corrosion, damage, wear-out or first signs of


soiling on steering rack can be seen, complete
steering gear must be replaced.

„ If no grease film is visible on steering rack, steering


gear must also be replaced completely.

Installing and adjusting

- Coat new thrust piece (contact surface at steering gear),


sealing ring and hole in steering gear housing with grease
G 052 192 A1 supplied - arrows - .

Caution!

Do not use other grease under any circumstances.


Electromechanical steering gear, servicing (Generation I) Стр. 36 из 43

- Insert thrust piece in steering gear housing.

- Install new sealing ring - arrow - and new spring.

- Tighten new adjustment screw to 40 Nm.

- Peen adjustment screw 6 times - arrows - using a


punch.

Punch points must be applied 2 graduation lines next to the


drill out punch points.

- Mark one graduation line of adjustment screw on the


steering gear housing - 1 - .

- Remove adjustment screw 6 graduation lines toward left -


Electromechanical steering gear, servicing (Generation I) Стр. 37 из 43

2- .

While doing this, a loosening torque of at least 15 Nm must


be obtained.

If loosening torque is not obtained:

- Tighten adjustment screw to 40 Nm again.

- Reinforce 6 peenings using a punch.

- Check applied marking of adjustment screw graduation


line on steering gear housing, re-apply marking if
necessary.

- Remove adjustment screw 6 graduation lines toward left.

A loosening torque of at least 15 Nm must be obtained.

- Remove rubber plug from adjustment screw.

- Attach a dial gauge with 0.001 graduations as depicted in


the illustration.

- Tension dial gauge to 1 mm pre-load.

- Rotate to tighten steering rack using torque wrench


V.A.G 1331 and 38 mm open end wrench insert V.A.G
1923 on tie rod to 40 Nm in one direction. When torque
wrench V.A.G 1331 disengages, set dial gauge to "0" .

- Remove torque wrench V.A.G 1331 from tie rod.

- Read off value indicated on dial gauge.

Specification: 0.0 to 0.05 mm


Electromechanical steering gear, servicing (Generation I) Стр. 38 из 43

- Turn steering using T10304 from left stop to right stop.


While doing this, observe values indicating on dial gauge.

Specification: 0.05 to 0.12 mm

Note:

„ If specified values for steering rack play are not


obtained, steering gear must be replaced
completely!

- Remove dial gauge and adapter, press rubber plug in


adjustment screw.

- Pull off left boot from steering gear housing.

- Turn steering from left stop to right stop, while doing this
grease visible area of steering rack with grease G 052 192
A1 supplied.

Caution!

Do not use other grease under any circumstances.

- Install left boot on to steering gear housing with new


clamp.

- Determine starting torque of steering.


Electromechanical steering gear, servicing (Generation I) Стр. 39 из 43

- First turn steering toward right in direction of travel until it


stops.

- Turn steering uniformly toward left until it stops on friction


meter, e.g. VAS 6222 . While doing this, read off steering
torque.

Specification: 3 2 Nm

1 - Friction meter, e.g. VAS 6222


2 - 24 mm socket

If steering torque is exceeded:

- Remove adjustment screws for thrust piece on steering


pinion side about one graduation line (turn adjustment
screws toward left).

- Check steering torque Topic 48-7 .

If steering torque falls short:

- Screw in adjustment screws for thrust piece on steering


pinion side about one graduation line (turn adjustment
screws toward right).

- Check steering torque Topic 48-7 .

- Steering gear, installing 48-5, Steering gear,


installing .

- Perform vehicle alignment 44-6, Wheel alignment .

- Perform basic setting for Steering Angle Sensor G85 via


Vehicle Diagnosis, Testing and Information System VAS
5051B , "Guided Fault Finding" .

- Phen perform basic setting of steering system via


Vehicle Diagnosis, Testing and Information System VAS
5051B "Guided Fault Finding" .

Servo motor with control module, removing and


installing
Electromechanical steering gear, servicing (Generation I) Стр. 40 из 43

Special tools, testers and auxiliary items


required

„ Holding fixture VW 313

„ Thrust piece 3253/6 qty. 2

„ Torque wrench V.A.G 1331

„ Transmission support T10108

„ 2 bolts M10 x 60

Removing

- Steering gear, removing 48-5, Steering gear, removing


and installing .
Electromechanical steering gear, servicing (Generation I) Стр. 41 из 43

- Clean steering gear in area of servo motor with control


module.

- Tension steering gear using 2 bolts M10 x 60 as depicted


in the illustration.

- Remove hydraulic thrust piece 48-7, Hydraulic thrust


piece, replacing and adjusting .

- Rotate steering gear in mounting bracket so that steering


pinion points upward.

- Disconnect connector from control module.

- To do so, press button - A - in direction of - arrow - and


then disconnect connector.
Electromechanical steering gear, servicing (Generation I) Стр. 42 из 43

- Remove mounting bolts - 1 - and remove servo motor


with control module from steering gear housing.

Note:

„ When removing bolts, secure servo motor with


control module from falling down (with second
technician if necessary).

- Clean sealing surfaces.

No seal remnants must enter steering gear housing


when cleaning sealing surfaces.

Note:

„ If corrosion, damage, wear-out or first signs of


soiling on steering rack can be seen, complete
steering gear must be replaced.

„ If no grease film is visible on steering rack, steering


gear must also be replaced completely.

Installing

- Pull a new sealing ring on to servo motor with control


module.

Before installation, servomotor pinion must be coated with


grease from repair kit G 052 192 A1 .

Caution!

Do not use other grease under any circumstances.

- Lubricate pinion.

- Coat sealing surfaces - arrow - with Curil K2 .


Electromechanical steering gear, servicing (Generation I) Стр. 43 из 43

- Insert servo motor with control module into steering gear


housing and tighten in diagonal sequence with new bolts -
1- .

- Connect harness connector of sensor wire to Power


Steering Control Module J500 .

Connector must engage audibly.

- Install new hydraulic thrust piece 48-7, Installing and


adjusting .

Replacement part set contains a new hydraulic thrust piece


among other items.

Tightening torques 48-3, Steering, torque


specifications .

- Steering gear, installing 48-5, Steering gear,


installing .

- Perform vehicle alignment 44-6, Wheel alignment .

- Perform basic setting for Steering Angle Sensor G85 via


Vehicle Diagnosis, Testing and Information System VAS
5051B , "Guided Fault Finding" .

- Perform basic setting of steering system via Vehicle


Diagnosis, Testing and Information System VAS
5051B "Guided Fault Finding" .

Das könnte Ihnen auch gefallen