Beruflich Dokumente
Kultur Dokumente
Table of Contents
Step 4: Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Related Instructables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
http://www.instructables.com/id/Arduino-controlled-Bluetooth-bot/
Author:johndavid400 author's website
I have always been one to take things apart to figure out how they work, so most of what I own has been dismantled. If it can't be taken apart or hacked, i'd
rather not have it. And I like to do things the cheapest way possible, because I like to do a lot of things and I don't have a lot of money.
Image Notes
1. The assembled Bluetooth-bot
Image Notes
1. Sparkfun Bluetooth Mate Gold - this is needed to receive the signals from the
bluetooth dongle (connected to PC) and translate them into a serial signal that the
Arduino can interpret.
http://www.instructables.com/id/Arduino-controlled-Bluetooth-bot/
Image Notes
1. Bluetooth Mate Gold from Sparkfun
2. Arduino Duemilanove
3. Home-made L298 motor-controller PCB (Eagle files included)
4. Tank tracked RC toy from thrift store (electronics removed)
5. A tank tracked vehicle should have separate drive motors for each side
(Left and Right)
Image Notes
1. A small Asus bluetooth dongle - works great.
2. A larger Motorola bluetooth dongle - also works great. You will only need
one of these.
First, strip the R/C car you got from the thrift-store, of all its electronic guts. This includes the motor-controller, R/C crystal, and any other PCB's installed. We will only
need two wires to each motor and a set of wires to the battery compartment. The code for this project is intended for use with a "tank-steer" type robot, utilizing one motor
on each side of the robot, like a tank. With bi-directional control of each motor, we can turn the robot in a circle without moving forward or reverse (called a "zero-turn
radius"). This type of control is extremely effective, especially at slower speeds.
Note: You do not have to have find a toy vehicle with tank tracks, there are many R/C toys at the thrift-store that have wheels, but utilize tank steering - just make sure
your vehicle has a drive motor installed on each side. I was able to find several "tracked" tank-steering vehicles at my local thrift-store, with regular visits and a few
months time.
Once you remove the old electronic circuits from the toy, we will need a place to mount the Arduino board, the motor-controller PCB, and the small Bluetooth adapter (we
will use the battery compartment built in to the toy). If you use an Ardumoto shield for the Arduino, you will only need a place to mount the Arduino. I used a hot-glue gun
to add a small blob of glue to the top of the toy base - then mount the Arduino. Using low-temp glue will keep the Arduino securely attached, but also allow you to remove
it later without damage if desired.
I designed a small PCB that uses an L298N dual motor driver IC to control (2) DC motors in either direction and with full speed control. The PCB files were created using
the freeware version of Eagle CAD and can be used to build your own motor-controller. If you would not like to build your own PCB, you can buy the Ardumoto motor-
controller from Sparkfun.com which uses a surface mount version of the same L298N IC (control pin reassignment may be required in the code).
Download the Eagle files for the L298N motor-controller and code for this project here:
https://sites.google.com/site/arduinorobotics/arduino-robotics/free_project
http://www.instructables.com/id/Arduino-controlled-Bluetooth-bot/
Image Notes
1. Bluetooth-bot
2. Larger brother of Bluetooth-bot
Image Notes
3. The various thrift-store toys that I have found that are tank-steering. 1. Remove old PCB from toy car - all you will need left on the base is the
4. Robot base used for Wally the wall-bot
battery compartment and wires going to each motor.
2. Arduino Mega and home-made motor-controller.
3. Arduino Duemilanove and L298N dual motor-controller (with bluetooth mate)
4. A stripped toy base with no electronics - this is what the toy should look like
before mounting the Arduino and motor-controller.
Image Notes
1. We will reuse the battery compartment that holds (4) AA batteries. You can
solder some new wires to the top of the battery compartment if you need them to
be longer.
The L298N motor driver IC uses 3 inputs for each motor (input A, input B and Enable) to determine both speed and direction. Speed control is most easily accomplished
by setting the inputs A and B to determine the direction and using the Enable pin to apply the PWM speed control signal.
http://www.instructables.com/id/Arduino-controlled-Bluetooth-bot/
Image Notes
1. The inputs from the L298N to the Arduino.
2. Connect Bluetooth mate Tx and Rx pins to Arduino Rx and Tx (pins 0 and 1). Then connect +5v and GND signals from the Bluetooth mate to the Arduino +5v and
GND supply.
3. Connect left motor to M1 on L298 and right motor to M2.
With the code loaded, you will need to "pair" the bluetooth adapter and Bluetooth Mate on your computer. The process to do this will be slightly different depending on
what Operating System you are using. First plug in any standard bluetooth adapter
The following steps will describe how to pair your Bluetooth device using Ubuntu 10.10:
Step 1. Turn On Bluetooth-bot and make sure the power LED on the Bluetooth mate is On (blinking red).
Step 2. Open your bluetooth manager (System > Preferences > Bluetooth Manager) - if not installed, open terminal and type:
"sudo aptitude install blueman", and then continue.
Step 3. Click the Search button to discover new devices.
Step 4. Right click on the Bluetooth Mate from the list (mine was listed as "FireFly - A4C7") and select the option for "Serial port" - you might also see your cell phone
show up on the list if available, make sure you select the correct device.
Step 5. Now you will see a dialog box asking for the passcode of the Bluetooth Mate - mine was set by default to "1234".
Step 6. With the passcode entered, your Bluetooth Mate should now be connected to your PC - the red blinking light on the Bluetooth mate will turn solid green to let you
know that it is connected.
Step 7. To control the bot, open a terminal and type the following: "screen /dev/rfcomm0 115200"
The full instructional video on how to set up your Bluetooth-bot with your PC is here:
Now you should be controlling your robot using the keyboard. Make sure the Caps lock is turned Off and use the following keys (lower-case i, j, k, and l) to make your
robot move. Holding a key down will result in constant movement, let go and the bot should stop:
forward = "i"
http://www.instructables.com/id/Arduino-controlled-Bluetooth-bot/
reverse = "k"
left = "j"
right = "l"
Additionally, you can change the speed value that is written to the motors by pressing the period, comma, and back-slash keys. The "comma" key is used to lower the
speed value (from 0-255), the "period" key is used to raise the speed value (increments of 5), and the "back-slash" key is used to set the speed_value to 255 (max).
Any other key that is pressed on the computer keyboard with the terminal open, will yield a response (the LED will blink), but no motor action will be commanded. If you
would like to assign different keys to the control functions, simply open the serial monitor (at 115,200 bps) and press the key you would like to use - the Arduino will
display the BYTE value on the serial monitor of any key that is pressed, so you can record the value shown and modify the sketch accordingly.
Once you get your Bluetooth-bot working, feel free to add more movement functions and modify the code as you please - if you mess it up, just download the original
code again. The code is also available on the next page for viewing.
Image Notes
1. Make sure robot passes first kitty inspection (seniority rules)...
Image Notes
1. If kitty says anything bad about your new robot
Image Notes
1. The bluetooth-bot during its second inspection.
Image Notes
1. The bluetooth
Step 4: Code
This code can be downloaded from the book website:
https://sites.google.com/site/arduinorobotics/arduino-robotics/free_project
// Bluetooth-bot v1
// Arduino Robotics unofficial chapter 14
// use Bluetooth Mate serial adapter to receive commands from PC
// Arduino decodes commands into motor movements
// Creates high-speed wireless serial link for robot control using keyboard
// Uses keys "i" = forward, "j" = left, "k" = reverse, and "l" = right
// speed control is also implemented using "," = speed down, "." = speed up, and "/" = max speed.
int M2_A = 4;
int M2_PWM = 3;
int M2_B = 2;
//////////////////////////////
void setup(){
TCCR2B = TCCR2B & 0b11111000 | 0x01; // change PWM frequency for pins 3 and 11 to 32kHz so there will be no motor whining
// declare outputs
pinMode(LED, OUTPUT);
pinMode(M1_A, OUTPUT);
pinMode(M1_PWM, OUTPUT);
pinMode(M1_B, OUTPUT);
pinMode(M2_A, OUTPUT);
pinMode(M2_PWM, OUTPUT);
pinMode(M2_B, OUTPUT);
delay(500);
////////////////////////////////////
void loop(){
http://www.instructables.com/id/Arduino-controlled-Bluetooth-bot/
}
// if byte is equal to "106" or "j", go left
else if (incomingByte == 106){
M1_reverse(speed_val);
M2_forward(speed_val);
delay(25);
}
// if byte is equal to "108" or "l", go right
else if (incomingByte == 108){
M1_forward(speed_val);
M2_reverse(speed_val);
delay(25);
}
// if byte is equal to "107" or "k", go reverse
else if (incomingByte == 107){
M1_reverse(speed_val);
M2_reverse(speed_val);
delay(25);
}
// otherwise, stop both motors
else {
M1_stop();
M2_stop();
}
else {
M1_stop();
M2_stop();
digitalWrite(LED, LOW);
}
}
void test_speed(){
// constrain speed value to between 0-255
if (speed_val > 250){
speed_val = 255;
Serial.println(" MAX ");
}
if (speed_val < 0){
speed_val = 0;
Serial.println(" MIN ");
}
void M1_stop(){
digitalWrite(M1_B, LOW);
digitalWrite(M1_A, LOW);
digitalWrite(M1_PWM, LOW);
}
void M2_stop(){
digitalWrite(M2_B, LOW);
digitalWrite(M2_A, LOW);
digitalWrite(M2_PWM, LOW);
}
http://www.instructables.com/id/Arduino-controlled-Bluetooth-bot/
Related Instructables
PIC RC Motor
Controller (and DIY Mod an Hexapod robot
example lego Omnibot 80's (video) by
Arduino Airsoft Seeed Pet by Belvedere - A Robot with aggrav8d
robot) by
Turret by jimbo.we Butler Robot by Voice, Camera,
PaulMakesThings Servos,
12grahamb wolffan
Bluetooth by
djsures
http://www.instructables.com/id/Arduino-controlled-Bluetooth-bot/