Sie sind auf Seite 1von 14

70-17

Door trims
Special tools

3392 Removing pliers


70-18

Driver's side front door trim, removing and installing

Note:

Removing and installing driver's side front door trim for vehicles with
manual window regulators is the same as removing and installing
passenger's side front door trim Page 70-22 .

Assembly overview

1 - Trim
2 - Grip recess
3 - Trim
4 - Front screw
5 - Three lower screws
6 - Three screws behind grip recess
7 - Locking knob
70-19

WARNING!

Disconnect battery ground (GND) strap


before working on the electrical system.

Removing

Notes:

Obtain radio unit code before disconnecting


battery.

Screwdriver with thin blade must be used to


prevent damaging trim and grip recess because
separating joint is very tight.

Do not grasp in grip depression when pulling off


grip recess as a strut secured to door trim is
underneath.

- Insert flat blade screwdriver into lower separating joint between trim -1- and grip recess
-2- and carefully pry trim off toward door.
70-20

- Unclip grip recess -2- out of door trim upward. Do not grip in depression to prevent
damage to strut -1-.
- Press locking lug against connector -3- -arrow- and pull off.

- Remove seven screws -arrows-.


- Unclip door trim -1- at sides using removal tool 3392.
- Lift door trim upward off window slot trim.
70-21

- Unclip cable guide -1- using flat blade screwdriver -2-, pull out from retainer -3- in
direction of arrow and unhook cable hook -4-.
- Disconnect connectors.

Installing

- Pull window slot seal -1- off door trim and insert in the window slot.
- Remainder of installing is the reverse of removing.

Notes:
Check door trim clips before installing, replace if necessary and insert into door trim.
After connecting battery, check vehicle equipment (radio, clock, electric windows) as
per Repair Manual and/or Owner's Manual.
If engine Electronic Control Module (ECM) is subject to low voltage with ignition on,
DTC memory and Readiness code must be checked

Repair Manual, Fuel Injection & Ignition, Repair Group 01


70-22

Front passenger's side front door trim, removing and


installing

Assembly overview

1 - Trim
2 - Grip
3 - Trim
4 - Front screw
5 - Three lower screws
6 - Two screws behind trim
7 - Three clips
8 - Locking knob
70-23

WARNING!

Disconnect battery ground (GND) strap


before working on the electrical system.

Removing

Note:

Obtain radio code before disconnecting battery.

- Pry trim -1- out of grip -3- using flat blade screwdriver -2-.
70-24

- Remove screws -arrows-.


- Unclip door trim -1- using assembly pliers 3392.
- Lift door trim upward off window slot.

- Unclip cable guide -1- using flat blade screwdriver -2-, pull out from retainer -3- in
direction of arrow and unhook cable hook -4-.
- Disconnect connectors.
70-25

Installing

- Pull window slot seal -1- off door trim and insert in the window slot.
- Remainder of installing is the reverse of removing.

Notes:
Check door trim clips before installing, replace if necessary and insert into door trim.
Check plate nut for front upper screw is seated correctly.
After connecting battery, check vehicle equipment (radio, clock, electric windows) as
per Workshop manual and/or Owner's manual.
If engine Electronic Control Module (ECM) is subject to low voltage with ignition on,
DTC memory and Readiness code must be checked

Repair Manual, Fuel Injection & Ignition, Repair Group 01


70-26

Rear door trim, removing and installing

Assembly overview

1 - Trim
2 - Grip
3 - Trim
4 - Three clips
5 - Two screws behind trim
6 - Two lower screws
7 - Locking knob
70-27

WARNING!

Disconnect battery ground (GND) strap


before working on the electrical system.

Removing

Note:

Obtain radio code before disconnecting battery.

- Pry trim -1- out of grip -3- using flat blade screwdriver -2-.
70-28

- Remove screws -arrows-.


- Unclip door trim at sides using assembly pliers 3392.
- Lift door trim upwards off window slot.

- Unclip cable guide -1- with a flat blade screwdriver -2-, pull out from retainer -3- in
direction of arrow and unhook cable hook -4-.
- Disconnect connection -3-.
70-29

Installing

- Pull window slot seal -1- off door trim and insert in window slot.

Notes:
Check door trim clips before installing, replace if necessary and insert into door trim.
After connecting battery, check vehicle equipment (radio, clock, electric windows) as
per Repair Manual and/or Owner's Manual.
If engine Electronic Control Module (ECM) is subject to low voltage with ignition on,
DTC memory and Readiness code must be checked

Repair Manual, Fuel Injection & Ignition, Repair Group 01


70-30

Front door window triangular trim (with speaker),


removing

- Remove front passenger's side door trim Page 70-22 .


- Separate speaker connector -1-.
- Remove screw -2-.
- Pull top of speaker -3- off -arrow A- and separate from door -
arrow B-.

Das könnte Ihnen auch gefallen