Beruflich Dokumente
Kultur Dokumente
2
Company: Page: 1
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 07/12/2018
E-Mail:
Specifier's comments:
1 Input data
Channel type; bolt HAC-30 68/250 F; HBC-B 4.6F, M12 x 40 mm
Effective embedment depth hef = 68 mm
Channel specification Length: 250 mm, anchor spacing: 200 mm, projection: 25 mm,
width: bch = 41 mm, height: hch = 26 mm
Material Anchor & Channel: hot-dip galvanized
Channel bolt: hot-dip galvanized
Europ. Tech. Assessment (ETA) ETA-11/0006
Issued I Valid 01/02/2016 | -
Standard Design method SA TS 101:2015
Base material cracked, 40MPa, f'c = 40.0 N/mm2, h = 180 mm
Reinforcement Exist. Reinf.: Widely spaced
No edge reinf. present
Reinf. to control splitting not present
Tolerance data tolerance interval: -200 mm/200 mm
most unfavorable tolerance: 25 mm
2 Overall Result
Design ok! (Maximum utilization: 100%)
3 Geometry
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.au PROFIS Anchor Channel 1.6.2
Company: Page: 2
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 07/12/2018
E-Mail:
3.1 Fixtures/Channel bolt groups
Fixture 1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.au PROFIS Anchor Channel 1.6.2
Company: Page: 3
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 07/12/2018
E-Mail:
hef = 68
a1 a2
25 200 25
Fixture bolt group
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.au PROFIS Anchor Channel 1.6.2
Company: Page: 4
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 07/12/2018
E-Mail:
5 Verifications
5.1 Verifications for anchor channels under tension loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Anchor 3.661 10.111 37 ok
Connection anchor-channel 3.661 10.111 37 ok
Channel lip 3.250 11.056 30 ok
Channel bolt 3.250 16.850 20 ok
Flexure channel 0.122 0.657 19 ok
Pull-out 3.661 17.800 21 ok
Concrete cone 3.661 12.422 30 ok
Concrete splitting 3.661 15.457 24 ok
Concrete blow-out N/A N/A N/A N/A
Suppl. reinf. - steel N/A N/A N/A N/A
Suppl. reinf. - anchorage N/A N/A N/A N/A
5.1.1.3 Local flexure of channel lip (Fixture 1, Channel bolt 1.1, Channel a)
Ncb* ≤ NRd,s,l = NRk,s,l · f Ms,l
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.au PROFIS Anchor Channel 1.6.2
Company: Page: 5
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 07/12/2018
E-Mail:
5.1.1.5 Flexure of channel (Channel a)
Mch* ≤ MRd,s,flex = MRk,s,flex · f Ms,flex
5.1.2 Pull-out failure (Anchor a2, Channel a) (SA TS 101:2015 section 6.3.3 )
Na* ≤ NRd,p = NRk,p · f Mp
NRk,p = k2 · Ah · f'c
Ah [mm2]
89
Na* [kN] k2 f'c [N/mm2] NRk,p [kN] f Mp NRd,p [kN]
3.661 7.5 40.0 26.700 0.667 17.800
5.1.3 Concrete cone (Anchor a2, Channel a) (SA TS 101:2015 section 6.3.2 )
Na* ≤ NRd,c = NRk,c · f Mc
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si N
1+ · i
cr,N N0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc ) 1
cr,N
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5 · hef
0.5
y ch,c,N,1 = (cc )2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = ( )
c2,2
ccr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.au PROFIS Anchor Channel 1.6.2
Company: Page: 6
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 07/12/2018
E-Mail:
5.1.4 Concrete splitting (Anchor a2, Channel a), pull-out relevant (SA TS 101:2015 section 6.3.4 )
Na* ≤ NRd,sp = NRk,sp · f Msp
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si N
1+ · i
cr,sp N0
i=1
scr,sp = 2 · ccr,sp
0.5
y ch,e,N = (cc ) 1
cr,sp
≤ 1.0
0.5
y ch,c,N,1 = (cc )2,1
cr,sp
≤ 1.0
0.5
y ch,c,N,2 = (cc )2,2
cr,sp
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
( (h ) ) ≤ 2.0
2/3 2/3
y h,sp = (hh )min
≤ max 1.0 ; ef + ccr,sp
hmin
N0Rk [kN] s [mm] scr,sp [mm] y ch,s,N c1 [mm] ccr,sp [mm] y ch,e,N
26.700 200 408 0.780 100 204 0.700
c2,1 [mm] c2,2 [mm] y ch,c,N,1 y ch,c,N,2 y re,N
175 - 0.926 1.000 1.000
h [mm] hmin [mm] y h,sp
180 80 1.717
Na* [kN] NRk,sp [kN] f Msp NRd,sp [kN]
3.661 23.185 0.667 15.457
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.au PROFIS Anchor Channel 1.6.2
Company: Page: 7
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 07/12/2018
E-Mail:
5.2 Verifications for anchor channels under shear loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Channel bolt w/o lever arm 6.285 12.096 52 ok
Flexure channel lip w/o lever arm - 6.285 11.056 57 ok
perpendicular
Flexure channel lip w/o lever arm - N/A N/A N/A N/A
longitudinal
Channel bolt with lever arm N/A N/A N/A N/A
Flexure of channel lip w/ lever arm N/A N/A N/A N/A
Anchor - perpendicular 7.080 10.111 71 ok
Anchor - longitudinal N/A N/A N/A N/A
Connection anchor/channel - 7.080 10.111 71 ok
perpendicular
Connection anchor/channel - N/A N/A N/A N/A
longitudinal
Concrete pryout, perpendicular 7.080 24.843 29 ok
Concrete pryout, longitudinal N/A N/A N/A N/A
Concrete edge - perpendicular 7.080 7.852 91 ok
Concrete edge - longitudinal N/A N/A N/A N/A
Suppl. reinf. steel - perpendicular N/A N/A N/A N/A
Suppl. reinf. anchorage - N/A N/A N/A N/A
perpendicular
Suppl. reinf. steel - longitudinal N/A N/A N/A N/A
Suppl. reinf. anchorage - longitudinal N/A N/A N/A N/A
Vcb* [kN] Vcb,y* [kN] Vcb,x* [kN] VRk,s [kN] f Ms VRd,s [kN]
6.285 6.285 0.000 20.200 0.599 12.096
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.au PROFIS Anchor Channel 1.6.2
Company: Page: 8
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 07/12/2018
E-Mail:
5.2.1.2 Local flexure of channel lip - shear perpendicular w/o lever arm (Fixture 1, Channel bolt 1.1, Channel a) (SA TS
101:2015 section 7.3.1.2)
5.2.1.3 Anchor - shear perpendicular (Anchor a2, Channel a) (SA TS 101:2015 section 7.3.1.1)
Va,y* ≤ VRd,s,a,y = VRk,s,a,y · f Ms
5.2.1.4 Connection between anchor and channel - shear perpendicular (Anchor a2, Channel a) (SA TS 101:2015 section
7.3.1.1)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.au PROFIS Anchor Channel 1.6.2
Company: Page: 9
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 07/12/2018
E-Mail:
5.2.2 Concrete pry-out failure - shear perpendicular (Anchor a2, Channel a) (SA TS 101:2015 section 7.3.3 )
Va,y* ≤ VRd,cp,y = VRk,cp,y · f Mc
VRk,cp,y = k8 · NRk,c
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc ) 1
cr,N
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.au PROFIS Anchor Channel 1.6.2
Company: Page: 10
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 07/12/2018
E-Mail:
5.2.3 Concrete edge failure - shear perpendicular, direction y- (Anchor a2, Channel a) (SA TS 101:2015 section 7.3.2 )
Va,y* ≤ VRd,c,y = VRk,c,y · f Mc
1
y ch,s,V = ≤ 1.0
nch,V
S[(1 - s ) ]
1.5
si V
1+ · i
cr,V V0
i=1
scr,V = 4 · c1 + 2 · bch
0.5
y ch,c,V,1 = (cc )
2,1
cr,V
≤ 1.0
0.5
y ch,c,V,2 = (cc )
2,2
cr,V
≤ 1.0
0.5
y ch,h,V = h
h
( )
cr,V
≤ 1.0
hcr,V = 2 · c1 + 2 · hch
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.au PROFIS Anchor Channel 1.6.2
Company: Page: 11
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 07/12/2018
E-Mail:
5.3 Combined tension and shear loads (SA TS 101:2015 section 8, Hilti method based on CEN-TR section 7.3)
Proof of interaction performed independently for steel failure of channel bolt, steel failure of the channel and concrete failure
5.3.1 Channel bolt (Fixture 1, Channel bolt 1.1)
2 2
2
bN,s =(NN * ) = 0.03720
cb
Rd,s,cb
2
=( ) = 0.26999
√V * + V *
cb,y
2
cb,x
2
bV,s
V Rd,s,cb
(Utilization : 31%)
5.3.2 Point of load application - channel lip (Fixture 1, Channel bolt 1.1)
k71 k71 k71
bN+V,la,c = max (NN cb*
Rd,s,l
;
Mch*
MRd,s,flex ) + (VV * ) ≤ (1.0 - (VV * ))
cb,y
Rd,s,l,y
cb,x
Rd,s,l,x
Mch* 2.0
bN,la,c = max (
Ncb*
;
NRd,s,l MRd,s,flex
= 0.08642 )
2.0
bV,la,c,y = (
Vcb,y*
VRd,s,l,y ) = 0.32318
2.0
bV,la,c,x (
= 1.0 - (
Vcb,x*
VRd,s,l,x ))
= 1.00000
(Utilization : 41%)
5.3.3 Anchor and connection between anchor and channel (Anchor a2)
k72 k72 k72
bN+V,ac = max (NN * , NN * )
a
Rd,s,a
a
Rd,s,c
+ max (VV a,y*
Rd,s,a,y
,
Va,y*
VRd,s,c,y ) ≤ (1.0 - max(VV a,x*
Rd,s,a,x
,
Va,x*
VRd,s,c,x ))
2.0
bN,ac = max (NN * , NN * ) = 0.13110
a
Rd,s,a
a
Rd,s,c
2.0
= max( ) = 0.49028
V * V *
a,y a,y
bV,ac,y ,
V VRd,s,a,y Rd,s,c,y
2.0
= (1.0 - max( )) = 1.00000
V * V * a,x a,x
bV,ac,x ,
V V Rd,s,a,x Rd,s,c,x
(Utilization : 63%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.au PROFIS Anchor Channel 1.6.2
Company: Page: 12
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 07/12/2018
E-Mail:
5.3.4 Concrete anchor (Anchor a2)
a a
bN+V,c = (NN *) + (VV *) ≤ 1.2
a
Rd
a,y
Rd,y
1.0
bN,c =(NN *)
a
Rd
= 0.29473
1.0
=(
V )
V *a,y
bV,c,y = 0.90160
Rd,y
(Utilization : 100%)
has to be designed accordingly. The design of the anchorplate/bracket must be done seperatly (outside the
PROFIS software) by the engineer.
• A longitudinal reinforcement should be provided along the edge of the member!
• Existing reinforcement and supplementary reinforcement as a PROFIS input should only be selected if the engineer has
verified the design of the concrete substructure complies with the associated reinforcement requirements contained in SA TS
101:2015 and/or in the relevant concrete standard.
• Any as-built conditions which vary from the PROFIS inputs (e.g., use of alternative product, variations in supplementary
reinforcement or base material, changes in load condition...), renders the PROFIS design invalid and requires recalculation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.au PROFIS Anchor Channel 1.6.2
Company: Page: 13
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 07/12/2018
E-Mail:
6 Installation data
6.1 Fixture 1
Plate type: - Bolt type: HBC-B 4.6F, M12 x 40 mm
Plate dimensions: 200 mm x 100 mm x 8 mm Bolt length: 40 mm
Profile: - Bolt diameter: 12 mm
Anchorplate design calculated: no Diameter hole: 14 mm
Installation torque: 0.025 kNm
100 100
50
50
1.1 1.2 x
50
50
25 150 25
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.au PROFIS Anchor Channel 1.6.2
Company: Page: 14
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 07/12/2018
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan