Beruflich Dokumente
Kultur Dokumente
Configuration (IPM
Broadband Services)
ISSUE 1.0
The slide is drafted according to the
<UA5000 Operation Manual --- IPM
Volume>.
!
Chapter 1 ADSL Service Configuration
"
xDSL Overview
#
xDSL Performance Summary
Comparison of xDSL Technical Characteristics:
Index ADSL VDSL SHDSL
ITU-T G.992.1
No standard
Standards ITU-T G.992.2 ITU-T G.991.2
currently
ANSI T1.413,Issue2
Asymmetric
Speeds Symmetric Symmetric
Supported (bit/s) 6–8M downstream, 640K–
12M 192K - 2312k
1M upstream
Wire pairs 1 1 1 or 2
$
Example: ADSL
Carrier# 7 16 31 64 255
Voice
26KHz 4.3125KHz 1.1MHz
Band
%
Example: ADSL
ATM/IP DSLAM PC
ADSL modem
High-pass High-pass
filter filter
&
Steps for Adding ADSL subscribers
Command List:
Step Description Command
1 Add and confirm an ADL board (Optional)
UA5000(config)#board confirm
'
Networking for ADSL Service
IP
I I P P S V A
P P V V D D D
M M M M L L L
ADSL Modem
(
Step 1: Add ADSL Service Boards
huawei(config)#board confirm
{ frameid[/slotid]<S><1,5> }:0/16
Step 2: Configure ADSL Line Profile
The UA5000 has an embedded ADSL line profile, with the
profile ID of 1, which can be used for the common ADSL
service
Display the existed ADSL line profile
huawei(config)#display adsl line-profile
Add a new ADSL line profile
huawei(config)#adsl line-profile add
{ <cr>|profile-index<L><2,999> }:
Command:
adsl line-profile add
Start adding profile………
Step 2: Configure ADSL Line Profile
One example: the upstream bandwidth is set as 512 kbit/s, and the
downstream bandwidth as 1 Mbit/s.
Do you want to name the profile (y/n) [n]:n
> Please choose default value type 0-adsl 1-adsl2+ (0~1)
[0]:0
……..
> 0-fixed 1-adaptAtStartup (0~1) [1]:1
……..
> Maximum transmit rate in downstream (32~32000 Kbps) [6144]:
1024
……..
> Maximum transmit rate in upstream (32~3000 Kbps) [640]:
512
Add profile 3 successfully
!
Step 3: Configure ADSL Alarm Profile
You can use the ADSL alarm profile to set alarm thresholds, to
count and supervise the performances of an active ADSL line.
Once the threshold is exceeded, the UA5000 will inform the
equipment of the event, and send alarms to the log host and the
NMS.
You can configure a specific alarm profile for the ADSL service. For
example, there are following requirements:
1) The threshold of the local end power-off is 60s.
2) The line initialization failure will be reported.
3) Alarms will be reported after the link re-training failure reaches
three times
"
Step 3: Configure ADSL Alarm Profile
huawei(config)#adsl alarm-profile add
{ <cr>|profile-index<L><2,50> }:
Command:
#
Step 3: Configure ADSL Alarm Profile
<ATU-R >
……..
$
Step 4: Bundle the ADSL alarm profile
huawei(config-if-adsl-0/16)#alarm-config 0 2
%
Step 5: Activate the ADSL port
To use adopt new line profile, we need to deactivate the port and activate it with new line
profile
huawei(config-if-adsl-0/16)#deactivate 0
0 is Port Number ID.
huawei(config-if-adsl-0/16)#activate
{ PortID<L><0,31>|all<K> }:0
{ <cr>|profile-index<K>|profile-name<K> }:profile-index
{ profile-index<L><1,1002> }:3
huawei(config-if-adsl-0/16)#display port state 0
----------------------------------------------------------------------
Port Status Line_Profile Alm_Profile
-----------------------------------------------------------------------
0 Activated 3 2
-------------------------------------------------------------------------------
&
Step 6: Configure New Traffic Parameters (Upstream)
Config traffic table for both upstream and downstream
{ cbr<K>|ubr<K>|rt-vbr<K>|nrt-vbr<K> }:ubr
{ tdtype<K> }:tdtype
{ NoTrafficDescriptor<K>|NoClpTaggingNoScr<K>|NoClpNoScrCdvt
<K>|NoClpNoScr<K> }:noclpnoScr
{ Clp01Pcr<K> }:clp01Pcr
{ pcrval<U><1,599039> }:512
{ <cr>|priority<K>|EnPPDisc<K>|EnEPDisc<K> }:
'
Step 6: Configure New Traffic Parameters (Upstream)
--------------------------------------------------------------------
TD Index : 7 //The upstream traffic entry index is 7.
Priority :0
Priority policy : tag-pri
CAR : 512 kbps
TD Type : NoClpNoScr
Service category : ubr
Referenced Status: not used
EnPPDISC : off
EnEPDISC : off
Clp01Pcr : 512 kbps
------------------------------------------------
(
Step 6: Configure New Traffic Parameters (downstream)
Set downstream traffic parameters
{ cbr<K>|ubr<K>|rt-vbr<K>|nrt-vbr<K> }:ubr
{ tdtype<K> }:tdtype
{ NoTrafficDescriptor<K>|NoClpTaggingNoScr<K>|No
ClpNoScrCdvt<K>|NoClpNoScr<K> }:noclpnoScr
{ Clp01Pcr<K> }:clp01Pcr
{ pcrval<U><1,599039> }:1024
{ <cr>|priority<K>|EnPPDisc<K>|EnEPDisc<K> }:
!
Step 7: Configure the upstream port and VLAN
Configure VLAN
huawei(config)#vlan
{ vlanid<U><1,4000> }:2
{ mux<K>|standard<K>|smart<K>|to<K> }: smart
huawei(config)#port vlan
{ vlanid<U><1,4000> }:2
{ frame/slot<S><3,4>|to<K> }:0/2
{ portlist<S><1,256> }:2
"
Step 8: Configure a virtual service
huawei(config)#service-port
{ vlan<K> }:vlan
{ vlan<U><1,4000> }:2 //Identical with the upper layer equipment
{ atm<K>|vdsl<K>|adsl<K>|shdsl<K> }:adsl
{ frame/slot/port<S><1,15> }:0/16/0
{ rx-cttr<K>|vpi<K> }:vpi
{ vpi<U><0,4095> }:0 //Identical with the Modem side setting
{ rx-cttr<K>|vci<K> }:vci
{ vci<U><32,65535> }:38 //Identical with the Modem side setting
{ rx-cttr<K> }:rx-cttr
{ rx-index<U><0,511> }:8 //Reference the traffic entry that meets your traffic requirements.
{ tx-cttr<K> }:tx-cttr
{ tx-index<U><0,511> }:7 //Reference the traffic entry that meets your traffic requirements.
Add service virtual port successfully!
#
Step 9: Query the Line Operation Parameters
$
Step 10: Save data
huawei(config)#save
%
Chapter 1 ADSL Service Configuration
&
About VDSL Service
'
About VDSL Service
!(
Networking for VDSL Service
IP
I I P P S V A
P P V V D D D
M M M M L L L
VDSL Modem
!
Configuration Procedure for VDSL Service
4 Set the port mode of the VDSL port (Optional) UA5000(config-if-vdsl-0/15)#port mode
!
Step 1: Add VDSL Service Boards
huawei(config)#board confirm
{ frameid[/slotid]<S><1,5> }:0/15
!!
Step 2: Configure VDSL Line Profile and alarm profile
!"
Step 2: Configure VDSL Line Profile and alarm profile
!#
Step 2: Configure VDSL Line Profile and alarm profile
The UA5000 has an embedded VDSL alarm profile,
with the profile ID of 1, which can be used for the
common VDSL service
Add a new VDSL line profile
huawei(config)#vdsl alarm-profile
{ add<K>|modify<K>|delete<K> }:add
{ <cr>|profile-index<L><2,16> }:2
Command:
VDSL alarm-profile add 2
Start adding line-profile 2
……
!$
Step 3: Activate the VDSL port
To use adopt new line profile, we need to deactivate the port
first and then activate it using the new line profile.
huawei(config-if-vdsl-0/15)#deactivate 0
huawei(config-if-vdsl-0/15)#activate
{ PortID<L><0,15>|all<K> }:0
{ <cr>|profile-index<L><1,16> }:2
!%
Step 4: Configure the Work Mode of VDSL Port
huawei(config-if-vdsl-0/15)#port mode
{<portId>}{0-15}:0
<tagged>{tagged,untagged}:untagged
!&
Step 5: Configure the Default VLAN for VDSL Port
Set the VLAN as the VDSL port side as VLAN 20. It must be
a MUX VLAN.
!'
Step 5: Configure the Default VLAN for VDSL Port
huawei(config)#vlan 20 mux
huawei(config-if-vdsl-0/15)#default-vlanid
<portId>{0-15}:0
<vlanId>{1-4094}:20
"(
Step 6: Configure New Traffic Parameters (Upstream)
If the default traffic entries do not meet your requirements, configure a traffic
entry as follows:
{ cbr<K>|ubr<K>|rt-vbr<K>|nrt-vbr<K> }:ubr
{ tdtype<K> }:tdtype
{ NoTrafficDescriptor<K>|NoClpTaggingNoScr<K>|NoClpNoScrCdvt<K>|No
ClpNoScr<K> }:noclpnoScr
{ Clp01Pcr<K> }:clp01Pcr
{ pcrval<U><1,599039> }:8192
{ <cr>|priority<K>|EnPPDisc<K>|EnEPDisc<K> }:
"
Step 6: Configure New Traffic Parameters (Upstream)
--------------------------------------------------------------------
TD Index : 7 //The upstream traffic entry index is 7.
Priority :0
Priority policy : tag-pri
CAR : 8192 kbps
TD Type : NoClpNoScr
Service category : ubr
Referenced Status: not used
EnPPDISC : off
EnEPDISC : off
Clp01Pcr : 8192 kbps
------------------------------------------------
"
Step 6: Configure New Traffic Parameters(downstream)
Set downstream traffic parameters
huawei(config)#traffic table srvcategory
{ cbr<K>|ubr<K>|rt-vbr<K>|nrt-vbr<K> }:ubr
{ tdtype<K> }:tdtype
{ NoTrafficDescriptor<K>|NoClpTaggingNoScr<K>|No
ClpNoScrCdvt<K>|NoClpNoScr<K> }:noclpnoScr
{ Clp01Pcr<K> }:clp01Pcr
{ pcrval<U><1,599039> }:10240
{ <cr>|priority<K>|EnPPDisc<K>|EnEPDisc<K> }:
Create TD record successfully
"!
Step 6: Configure New Traffic Parameters (downstream)
--------------------------------------------------------------------
TD Index : 8 //The downstream traffic entry index is 8
Priority :0
Priority policy : tag-pri
CAR : 10240 kbps
TD Type : NoClpNoScr
Service category : ubr
Referenced Status: not used
EnPPDISC : off
EnEPDISC : off
Clp01Pcr : 10240 kbps
--------------------------------------------------------------------
""
Step 7: Configure the Upstream Port and VLAN
huawei(config-if-ipm-0/2)#duplex
{ portid<U><0,7>|all<K> }:0
{ half<K>|full<K>|auto<K> }:full
huawei(config-if-ipm-0/11)#speed 0 100m
huawei(config-if-ipm-0/11)#flow-control
{ portid<U><0,7>|all<K> }:0
"#
Step 7: Configure the Upstream Port and VLAN
"$
Step 8: Configure a Virtual Service Port
huawei(config)#service-port
{ vlan<K> }:vlan
{ vlan<U><1,4000> }:2 //Identical with the upper layer equipment
{ atm<K>|vdsl<K>|adsl<K>|shdsl<K> }:vdsl
{ frame/slot/port<S><1,15> }:0/15/0
{ rx-cttr<K>|vpi<K> }:vpi
{ vpi<U><0,4095> }:0 //Identical with the Modem side setting
{ rx-cttr<K>|vci<K> }:vci
{ vci<U><32,65535> }:38 //Identical with the Modem side setting
{ rx-cttr<K> }:rx-cttr
{ rx-index<U><0,511> }:8 //Reference the traffic entry that meets your traffic requirements.
{ tx-cttr<K> }:tx-cttr
{ tx-index<U><0,511> }:7 //Reference the traffic entry that meets your traffic requirements.
Add service virtual port successfully!
"%
Step 9: Query the Line Operation Parameters
"&
Step 10: Save data
huawei(config)#save
"'
Chapter 1 ADSL Service Configuration
#(
About SHDSL Service
SHDSL can provide symmetric high-speed access service, meeting
the high bandwidth requirements of medium/small enterprises and
SOHO subscribers.
The SHDSL service module has the following features.
The SHDSL line card uses the TC-PAM
modulation/demodulation mode and the symmetric transmission
mode.
The card provides two SHDSL lines, with the rate of 192 Kbps–
2312 Kbps. The system can adjust the SHDSL line rate to a
reasonable rate according to the line status, such as distance
and noise.
The SHDSL usage distance is 3 Km–6 Km.
The UA5000 uses the SDLB card to provide the SHDSL service.
#
Steps for Adding SHDSL subscribers
Configure the SHDSL line profile and alarm profile UA5000(config)#shdsl line-profile add
2
(Optional) UA5000(config)#shdsl alarm-profile add
UA5000(config-if-shdsl-0/15)#display port
3 Confirm the SHDSL port is activated
state
4 Configure traffic parameters (Optional) UA5000(config)# traffic table srvcategory
UA5000(config)#interface ipm
5 Configure the upstream port and VLAN (Optional)
UA5000(config)#port vlan
6 Configure a virtual service port UA5000(config)#service-port
7 Query link status after the port is activated UA5000(config-if-shdsl-0/15)#display line
8 Save data UA5000(config)#save
#
Networking for SHDSL Service
IP
I I P P S V A
P P V V D D D
M M M M L L L
SHDSL Modem
#!
Step 1: Add SHDSL Service Boards
Add an SDLB board
huawei(config)#board confirm
{ frameid[/slotid]<S><1,5> }:0/14
#"
Step 2: Configure SHDSL Line Profile and Alarm Profile
The UA5000 supports 2-wire and 4-wire SHDSL ports. The line
profiles for these two modes of ports are slightly different. The
following example adds a line profile for a 2-wire SHDSL port.
{ <cr>|profileIndex<L><2,16> }:2
Command:
……
##
Step 2: Configure SHDSL Line Profile and Alarm Profile
Do you use the default data to create a line profile? (y/n ) [y]: n
G.SHDSL interface mode of line (1--two wire;2--four wire)[1]:
G.SHDSL minimum line rate
(Value must be multiple of 64,192~2304 kbps)[2048]:1024
G.SHDSL maximum line rate
(Value must be multiple of 64,192~2304 kbps)[2048]:1024
…….
Add profile 2 successfully
#$
Step 2: Configure SHDSL Line Profile and Alarm Profile
Add a new SHDSL alarm profile
{ <cr>|profileIndex<L><2,16> }:2
Command:
#%
Step 2: Configure SHDSL Line Profile and Alarm Profile
ES threshold (0~900 s)[0]:
SES threshold (0~900 s)[0]:
CRC anomaly threshold (0~58981500)[0]:
LOSWS threshold (0~900 s)[0]:
UAS threshold (0~900 s)[0]:
Add profile 2 successfully
#&
Step 3: Activate the SHDSL port
To use adopt new line profile, we need to deactivate the port and
activate it with new line profile
huawei(config-if-sdl-0/14)#deactivate 0
huawei(config-if-sdl-0/14)#activate 0 2
huawei(config-if-sdl-0/14)#display port state 0
-----------------------------------------------------------------------------------------------
Port Running Control Line Alarm Running Config Bind
ID Status Status Profile Profile Operation Operation Status
--------------------------------------------------------------------------
0 Activated Activated 1 1 Normal None Normal
-------------------------------------------------------------------------- --------------------
#'
Step 4: Configure New Traffic Table
Config traffic table for both upstream and downstream
huawei(config)#traffic table srvcategory
{ cbr<K>|ubr<K>|rt-vbr<K>|nrt-vbr<K> }:ubr
{ tdtype<K> }:tdtype
{ NoTrafficDescriptor<K>|NoClpTaggingNoScr<K>|NoClpN
oScrCdvt<K>|NoClpNoScr<K> }:noclpnoScr
{ Clp01Pcr<K> }:clp01Pcr
{ pcrval<U><1,599039> }:1024
{ <cr>|EnPPDisc<K>|EnEPDisc<K> }:
Create TD record successfully
--------------------------------------------------------------------
TD Index : 7 //The upstream traffic entry index is 7.
$(
Step 5: Configure the Upstream Port and VLAN
huawei(config-if-ipm-0/2)#duplex
{ portid<U><0,7>|all<K> }:2
{ half<K>|full<K>|auto<K> }:full
huawei(config-if-ipm-0/2)#speed 0 100m
huawei(config-if-ipm-0/2)#flow-control
{ portid<U><0,7>|all<K> }:2
$
Step 5: Configure the Upstream Port and VLAN
Configure VLAN
huawei(config)#vlan
{ vlanid<U><1,4000> }:2
{ mux<K>|standard<K>|smart<K>|to<K> }: smart
huawei(config)#port vlan
{ vlanid<U><1,4000> }:2
{ frame/slot<S><3,4>|to<K> }:0/2
{ portlist<S><1,256> }:0
$
Step 6: Configure a Virtual Service Port
huawei(config)#service-port
{ vlan<K> }:vlan
{ vlan<U><1,4000> }:2 //Identical with the upper layer equipment
{ atm<K>|vdsl<K>|adsl<K>|shdsl<K> }:shdsl
{ frame/slot/port<S><1,15> }:0/14/0
{ rx-cttr<K>|vpi<K> }:vpi 0 //Identical with the Modem side setting
{ rx-cttr<K>|vci<K> }:vci 38 //Identical with the Modem side setting
{ rx-cttr<K> }:rx-cttr 7
{ tx-cttr<K> }:tx-cttr 7 //Reference the traffic entry that meets your
traffic requirements.
Add service virtual port successfully!
$!
Step 7: Query the Line Operation Parameters
$"
Step 8: Save data
huawei(config)#save
$#
Summary
Steps for xDSL service data?
How to query the line status after training?
$$
Thank You
www.huawei.com