Beruflich Dokumente
Kultur Dokumente
chassis PL13.11
TYPE B
39PFL2708/F7 PHILIPS (Serial No.: DS2)
TYPE C
39PFL2708/F7 PHILIPS (Serial No.: DS1)
39PFL4208/F8 PHILIPS (Serial No.: XA1)
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.
130817
1-1 PL13.11SP
Downloaded from www.Manualslib.com manuals search engine
IMPORTANT SAFETY PRECAUTIONS
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical
codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally
important to implement the following precautions when a set is being serviced.
Safety Precautions for LCD TV d. Leakage Current Hot Check - With the
instrument completely reassembled, plug the
Circuit AC line cord directly into a 120 V AC outlet. (Do
1. Before returning an instrument to the not use an isolation transformer during this
customer, always make a safety check of the test.) Use a leakage current tester or a
entire instrument, including, but not limited to, the metering system that complies with American
following items: National Standards Institute (ANSI) C101.1
a. Be sure that no built-in protective devices are Leakage Current for Appliances and
defective and have been defeated during Underwriters Laboratories (UL) 1410, (50.7).
servicing. (1) Protective shields are provided With the instrument AC switch first in the on
on this chassis to protect both the technician position and then in the off position, measure
and the customer. Correctly replace all missing from a known earth ground (metal water pipe,
protective shields, including any removed for conduit, etc.) to all exposed metal parts of the
servicing convenience. (2) When reinstalling instrument (antennas, handle brackets, metal
the chassis and/or other assembly in the cabinet, screw heads, metallic overlays, control
cabinet, be sure to put back in place all shafts, etc.), especially any exposed metal
protective devices, including but not limited to, parts that offer an electrical return path to the
nonmetallic control knobs, insulating chassis. Any current measured must not
fishpapers, adjustment and compartment exceed 0.5 milli-ampere. Reverse the
covers/shields, and isolation resistor/capacitor instrument power cord plug in the outlet and
networks. Do not operate this instrument or repeat the test.
permit it to be operated without all
protective devices correctly installed and READING SHOULD
functioning. Servicers who defeat safety NOT BE ABOVE 0.5 mA
features or fail to perform safety checks
may be liable for any resulting damage. LEAKAGE
DEVICE CURRENT
b. Be sure that there are no cabinet openings BEING TESTER
through which an adult or child might be able to TESTED + _
insert their fingers and contact a hazardous
voltage. Such openings include, but are not TEST ALL EXPOSED
limited to, (1) spacing between the Liquid METAL SURFACES
Crystal Panel and the cabinet mask, (2)
excessively wide cabinet ventilation slots, and
(3) an improperly fitted and/or incorrectly ALSO TEST WITH
secured cabinet back cover. PLUG REVERSED
c. Antenna Cold Check - With the instrument AC USING AC
plug removed from any AC source, connect an ADAPTER PLUG EARTH
electrical jumper across the two AC plug AS REQUIRED GROUND
prongs. Place the instrument AC switch in the
on position. Connect one lead of an ohmmeter ANY MEASUREMENTS NOT WITHIN THE
to the AC plug prongs tied together and touch LIMITS SPECIFIED HEREIN INDICATE A
the other ohmmeter lead in turn to each tuner POTENTIAL SHOCK HAZARD THAT MUST
antenna input exposed terminal screw and, if BE ELIMINATED BEFORE RETURNING THE
applicable, to the coaxial connector. If the INSTRUMENT TO THE CUSTOMER OR
measured resistance is less than 1.0 megohm BEFORE CONNECTING THE ANTENNA OR
or greater than 5.2 megohm, an abnormality ACCESSORIES.
exists that must be corrected before the
2. Read and comply with all caution and safety-
instrument is returned to the customer. Repeat
related notes on or inside the receiver cabinet, on
this test with the instrument AC switch in the off
the receiver chassis, or on the Liquid Crystal
position.
Panel.
2-1 LTVN_ISP
Downloaded from www.Manualslib.com manuals search engine
3. Design Alteration Warning - Do not alter or add 7. Product Safety Notice - Some electrical and
to the mechanical or electrical design of this TV mechanical parts have special safety-related
receiver. Design alterations and additions, characteristics which are often not evident from
including, but not limited to circuit modifications visual inspection, nor can the protection they give
and the addition of items such as auxiliary audio necessarily be obtained by replacing them with
and/or video output connections, might alter the components rated for higher voltage, wattage, etc.
safety characteristics of this receiver and create a Parts that have special safety characteristics are
hazard to the user. Any design alterations or identified by a # on schematics and in parts lists.
additions will void the manufacturer's warranty and Use of a substitute replacement that does not
may make you, the servicer, responsible for have the same safety characteristics as the
personal injury or property damage resulting recommended replacement part might create
therefrom. shock, fire, and/or other hazards. The product's
4. Hot Chassis Warning - safety is under review continuously and new
instructions are issued whenever appropriate.
a. Some TV receiver chassis are electrically
Prior to shipment from the factory, our products
connected directly to one conductor of the AC
are strictly inspected to confirm they comply with
power cord and maybe safety-serviced without
the recognized product safety and electrical codes
an isolation transformer only if the AC power
of the countries in which they are to be sold.
plug is inserted so that the chassis is
However, in order to maintain such compliance, it
connected to the ground side of the AC power
is equally important to implement the following
source. To confirm that the AC power plug is
precautions when a set is being serviced.
inserted correctly, with an AC voltmeter,
measure between the chassis and a known
earth ground. If a voltage reading in excess of
1.0 V is obtained, remove and reinsert the AC
power plug in the opposite polarity and again
measure the voltage potential between the
chassis and a known earth ground.
b. Some TV receiver chassis normally have 85V
AC(RMS) between chassis and earth ground
regardless of the AC plug polarity. This chassis
can be safety-serviced only with an isolation
transformer inserted in the power line between
the receiver and the AC power source, for both
personnel and test equipment protection.
c. Some TV receiver chassis have a secondary
ground system in addition to the main chassis
ground. This secondary ground system is not
isolated from the AC power line. The two
ground systems are electrically separated by
insulation material that must not be defeated or
altered.
5. Observe original lead dress. Take extra care to
assure correct lead dress in the following areas: a.
near sharp edges, b. near thermally hot parts-be
sure that leads and components do not touch
thermally hot parts, c. the AC supply, d. high
voltage, and, e. antenna wiring. Always inspect in
all areas for pinched, out of place, or frayed wiring.
Check AC power cord for damage.
6. Components, parts, and/or wiring that appear to
have overheated or are otherwise damaged
should be replaced with components, parts, or
wiring that meet original specifications.
Additionally, determine the cause of overheating
and/or damage and, if necessary, take corrective
action to remove any potential safety hazard.
2-2 LTVN_ISP
Downloaded from www.Manualslib.com manuals search engine
Precautions during Servicing
A. Parts identified by the # symbol are critical for
safety.
Replace only with part number specified.
B. In addition to safety, other parts and assemblies
are specified for conformance with regulations
applying to spurious radiation. These must also be
replaced only with specified replacements.
Examples: RF converters, RF cables, noise
blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components
(transformers, power cord, etc.), wrap ends of
wires securely about the terminals before
soldering.
F. Observe that the wires do not contact heat
producing parts (heat sinks, oxide metal film
resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp
edged or pointed parts.
H. When a power cord has been replaced, check that
11~13 lb (5~6 kg) of force in any direction will not
loosen it.
I. Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder
droplets, etc.) do not remain inside the set.
K. When connecting or disconnecting the internal
connectors, first, disconnect the AC plug from the
AC supply outlet.
L. When installing parts or assembling the cabinet
parts, be sure to use the proper screws and
tighten certainly.
2-3 LTVN_ISP
Downloaded from www.Manualslib.com manuals search engine
Safety Check after Servicing
Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and
wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified
values in order to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm
specified clearance distance (d) and (d') between
soldered terminals, and between terminals and Chassis or Secondary Conductor
surrounding metallic parts. (See Fig. 1)
Primary Circuit
Table 1: Ratings for selected area
Clearance d' d
AC Line Voltage Region
Distance (d), (d’)
U.S.A. or ≥ 3.2 mm
110 to 130 V
Canada (0.126 inches)
Fig. 1
Fig. 2
AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to:
U.S.A. or 0.15 μF CAP. & 1.5 kΩ RES. Exposed accessible
110 to 130 V i ≤ 0.5 mA rms
Canada Connected in parallel parts
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
2-4 LTVN_ISP
Downloaded from www.Manualslib.com manuals search engine
STANDARD NOTES FOR SERVICING
Circuit Board Indications How to Remove / Install Flat Pack-IC
1. The output pin of the 3 pin Regulator ICs is
1. Removal
indicated as shown.
With Hot-Air Flat Pack-IC Desoldering Machine:
Top View Bottom View 1. Prepare the hot-air flat pack-IC desoldering
Input machine, then apply hot air to the Flat Pack-IC
Out In (about 5 to 6 seconds). (Fig. S-1-1)
Pin 1
10
3-1 TVN_SN
Downloaded from www.Manualslib.com manuals search engine
3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron:
be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from
pin or the solder lands under the IC when all pins of the flat pack-IC. When you use solder
removing it. flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
Hot-air
Flat Pack-IC Flat Pack-IC Desoldering Braid
Desoldering
Machine
CBA
Soldering Iron
Masking Flat Pack-IC Fig. S-1-3
Tape
Tweezers 2. Lift each lead of the flat pack-IC upward one by
one, using a sharp pin or wire to which solder will
Fig. S-1-2
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air desoldering
machine. (Fig. S-1-4)
Sharp
Pin
Fine Tip
Soldering Iron
Fig. S-1-4
3-2 TVN_SN
Downloaded from www.Manualslib.com manuals search engine
With Iron Wire: 2. Installation
1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA
flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more
you can remove it easily. (Fig. S-1-3) easily.
2. Affix the wire to a workbench or solid mounting 2. The “ I ” mark on the flat pack-IC indicates pin 1.
point, as shown in Fig. S-1-5. (See Fig. S-1-7.) Be sure this mark matches the
3. While heating the pins using a fine tip soldering pin 1 on the PCB when positioning for installation.
iron or hot air blower, pull up the wire as the solder Then presolder the four corners of the flat pack-IC.
melts so as to lift the IC leads from the CBA (See Fig. S-1-8.)
contact pads as shown in Fig. S-1-5. 3. Solder all pins of the flat pack-IC. Be sure that
4. Bottom of the flat pack-IC is fixed with glue to the none of the pins have solder bridges.
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6) Example :
5. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be
taken to ensure that the flat pack-IC is not
being held by glue. When the flat pack-IC is
removed from the CBA, handle it gently
because it may be damaged if force is applied.
Pin 1 of the Flat Pack-IC
is indicated by a " " mark.
Hot Air Blower Fig. S-1-7
or
Presolder
Iron Wire
Soldering Iron
To Solid
Mounting Point
Fig. S-1-5
Flat Pack-IC
CBA
Flat Pack-IC
Tweezers
Fig. S-1-6
3-3 TVN_SN
Downloaded from www.Manualslib.com manuals search engine
Instructions for Handling Semi-
conductors
Electrostatic breakdown of the semi-conductors may
occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.
<Incorrect>
CBA
1MΩ
CBA
1MΩ
Conductive Sheet or
Copper Plate
3-4 TVN_SN
Downloaded from www.Manualslib.com manuals search engine
CABINET DISASSEMBLY INSTRUCTIONS
Screw Torque Specification Step/
Fig.
Loc. Part Removal Note
Ref. Part Tightening No.
No. Number Part Name Torque No.
SCREW P-TIGHT Stand Base
L9 GBHP3120 (3X12 BIND HEAD + 5.2±0.9lb·in [2] D1 --------------- ---
Assembly
BLK)
[3] Rear Cover D1 2(S-3), 10(S-4) ---
L23 GBJS3060 SCREW S-TIGHT
(M3X6 BIND HEAD+) 6.1±0.9lb·in
Power
SCREW S-TIGHT D2 5(S-5), CN601,
L27 GBHS3080 (M3X8 BIND HEAD+) 5.2±0.9lb·in [4] Supply ---
D5 CN501, CN1001
CBA
SCREW B-TIGHT
L35 GBJB3080 (D3X8 BIND HEAD+)
4(S-6), CN3906*1,
6.1±0.9lb·in
Digital Main D2 CN3013*2, CN3105*1,
L67 GBJS3100 SCREW S-TIGHT [5] ---
(M3X10 BIND HEAD+) CBA Unit D5 CN3101*2, CN3801,
STAND SCREW KIT Jack Holder
SSK1 1ESA34647 (DOUBLE SEMS
SCREW M4X20 + BLK) (approx. Stand
[6] D3 2(S-7) ---
STAND SCREW KIT 8.7±0.9lb·in)* Bracket
SSK2 1ESA34648 (DOUBLE SEMS
SCREW M4X10 + BLK) [7] Speaker D3 --------------- ---
4-1 PL13.11_DC
Downloaded from www.Manualslib.com manuals search engine
Important precautions concerning the • When disassembling, first detach the hooks on each
LCD Panel Assembly: end on the bottom side, then detach the remaining
hooks moving toward the center.
1. When you disassemble/re-assemble the X-PCB
Cover • Make sure the hooks are securely in place when
assembling.
• Be careful not to break the hooks. If you pull with too
much force, the hooks may be damaged. • Be careful not to scratch the display panel when
• When disassembling, first hold the top and bottom of assembling.
the X-PCB Cover on both ends and then moving • The Function CBA Unit and Sensor Lens are fixed in
toward the center, lift up the top side to detach the place by the hooks. Make sure these hooks are not
hooks. damaged. Make sure the Function CBA Unit and
• When assembling, be careful not to damage the Sensor Lens are securely in place when
X-PCB Board or the COF(Chip On Film). re-assembling.
• Make sure the hooks are securely in place when • The screw tightening torque must be 5.2lb·in
re-assembling. (6kgf·cm).
• The screw tightening torque must be 5.2lb·in • After replacing the Front Cabinet or Function CBA
(6kgf·cm). Unit, make sure the tact switches operate normally.
2. When you disassemble/re-assemble the Front • Make sure to replace the Control Plate to a new one
Cabinet or Function CBA Unit when replacing the Front Cabinet.
• Be careful not to break the hooks. If you pull with too
much force, the hooks may be damaged.
(S-4)
(S-3)
(S-4)
(S-4)
39PFL2708/F7,
39PFL2908/F7, (S-1)
39PFL4208/F8,
39PFL4408/F8 39PFL2608/F7 [1] Stand Neck
Assembly
(S-2) Fig. D1
4-2 PL13.11_DC
Downloaded from www.Manualslib.com manuals search engine
Type A
[5] Digital Main CBA Unit
(S-6)
Jack Holder
(S-5)
Type B, C
(S-6)
Jack Holder
Fig. D2
[7] Speaker
(S-7)
[7] Speaker
[6] Stand Bracket
Fig. D3
4-3 PL13.11_DC
Downloaded from www.Manualslib.com manuals search engine
[9] X-PCB Cover*1
Hook*2
[10] Front Cabinet*2 Hook*1
(S-8)
Hook*1
Hook*2
Hook*2
Hook*1
Shield Plate
2
Sensor Lens*
Hook*2
Control Plate*2
Fig. D4
*1: Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the
X-PCB Cover.
*2: Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the Front
Cabinet or Function CBA Unit.
4-4 PL13.11_DC
Downloaded from www.Manualslib.com manuals search engine
TV Cable Wiring Diagram
Digital Main
Power Supply CBA CBA Unit
CN1001
*1 CN3906
*2,*3 CN3013
*1 CN3601
CN501 *2 CN3701
*3 CN3602
CN601
*1 CN3105 CN3801
*2,*3 CN3101
To AC Cord
CN4052
*1: TYPE A
*2: TYPE B
*3: TYPE C
Fig. D5
4-5 PL13.11_DC
Downloaded from www.Manualslib.com manuals search engine
ELECTRICAL ADJUSTMENT INSTRUCTIONS
[TYPE A] 1. Purity Check Mode
General Note: “CBA” is abbreviation for This mode cycles through full-screen displays of red,
green, blue, and white to check for non-active pixels.
“Circuit Board Assembly.”
1. Enter the service mode.
Note: Electrical adjustments are required after
replacing circuit components and certain 2. Each time the [7] button on the remote control unit
mechanical parts. It is important to perform is pressed, the display changes as follows.
these adjustments only after all repairs and
Purity Check Mode
replacements have been completed.
Also, do not attempt these adjustments unless White mode
the proper equipment is available.
[7] button
Test Equipment Required
1. Remote control unit
2. Color Analyzer, [7] button
CA-310 (KONICA MINOLTA Luminance meter) or
Black mode
measuring instrument as good as CA-310.
[7] button
White 20% mode
Note:
When entering this mode, the default setting is White mode.
Color Analyzer
Internal (Single)
Internal (Single)
LDB 0
HDB 0
14. Press [7] button to select the “LDR” for Low Drive
7. Press [CHANNEL UP/DOWN] buttons to adjust Red adjustment (“LDR” appears in the screen.) and
the color temperature becomes 12000°K press [CHANNEL UP/DOWN] buttons to adjust the
(x= 0.272 / y= 0.278 ± 0.005). color temperature.
8. Press [1] button to select the “HDR” for High Drive 15. If necessary, adjust the “LDB” or “LDR” again.
Red adjustment (“HDR” appears in the screen.) 16. Press [CH RETURN] or [PREV CH] to shift to the
and press [CHANNEL UP/DOWN] buttons to initial screen in the service mode.
adjust the color temperature. If [White Balance] message with a green color is
9. If necessary, adjust the “HDB” or “HDR” again. displayed on the upper right of the screen, this
adjustment completes.
10. Press [6] button to select the “MDB” for Middle
If [White Balance] message with a red color is
Drive Blue adjustment (“MDB” appears in the
displayed, repeat above steps from 5. to 15. Then
screen.) and press [CHANNEL UP/DOWN] buttons
check the initial screen in the service mode again.
to adjust the color temperature.
If [White Balance] message with a red color is
displayed, replace the LCD Panel or Digital Main
CBA.
Internal (Single)
17. To cancel or to exit from the White Balance
Adjustment, press [CH RETURN] or [PREV CH]
button.
MDB 0
Safety: Safety_Non
HDMI EDID: **
HDMI UART: OFF Total Watch Time: *****
Touch Sensor Ver: -.-- / --- Lightsensor: **
5-4 PL13.7EA
Downloaded from www.Manualslib.com manuals search engine
1. Purity Check Mode 2. VCOM Adjustment
This mode cycles through full-screen displays of red, Test Point Adj. Point
green, blue, and white to check for non-active pixels. [CHANNEL UP/DOWN]
Screen
1. Enter the service mode. buttons
2. Each time the [7] button on the remote control unit M. EQ. Spec.
is pressed, the display changes as follows. Color analyzer See below
Purity Check Mode Figure
Perpendicularity
[7] button
Black mode
Color Analyzer
[7] button
1. Operate the unit for more than 60 minutes.
White 50% mode
2. Set the color analyzer at the zero point calibration
and bring the optical receptor pointing at the
center of the LCD-Panel.
Note: The optical receptor must be set
perpendicular to the LCD Panel surface.
[7] button 3. Enter the service mode.
Red, Green, Blue mode 4. Press [2] button on the remote control unit.
5. Press [CHANNEL UP/DOWN] buttons on the
remote control unit so that the color analyzer value
becomes minimum.
6. To cancel or to exit from the VCOM Adjustment,
press [CH RETURN] or [PREV CH] button.
[7] button
V-ramp mode
[7] button
White 20% mode
Note:
When entering this mode, the default setting is White mode.
5-5 PL13.7EA
Downloaded from www.Manualslib.com manuals search engine
The White Balance Adjustment should be 6. Press [MENU] button. The internal Raster signal
performed when replacing the LCD Panel appears in the screen. (“Internal (Single)” appears
in the upper right of the screen as shown below.)
or Digital Main CBA.
3. White Balance Adjustment
Internal (Single)
Purpose: To mix red and blue beams correctly for
pure white.
Symptom of Misadjustment: White becomes bluish
or reddish.
x= 0.272 ± 0.005
Color temperature
y= 0.278 ± 0.005
7. Press [CHANNEL UP/DOWN] buttons to adjust
Internal pattern
Input Signal the color temperature becomes 12000°K
(40/80% raster)
(x= 0.272 / y= 0.278 ± 0.005).
Measurement point Screen center
8. Press [1] button to select the “HDR” for High Drive
CA-310 (KONICA MINOLTA Red adjustment (“HDR” appears in the screen.)
Luminance meter) or and press [CHANNEL UP/DOWN] buttons to
M. EQ.
measuring instrument as adjust the color temperature.
good as CA-310.
9. If necessary, adjust the “HDB” or “HDR” again.
60min.
10. Press [6] button to select the “LDB” for Low Drive
Aging time (Retail MODE/100IRE Raster
HDMI 1080i@60) Blue adjustment (“LDB” appears in the screen.)
and press [CHANNEL UP/DOWN] buttons to
Shipment setting/ adjust the color temperature.
MODE setting of TV
Retail MODE
Ambient
25°C ± 5°C
temperature Internal (Single)
5-6 PL13.7EA
Downloaded from www.Manualslib.com manuals search engine
HOW TO INITIALIZE THE LCD TV
The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to
select a language and program channels after the set has been initialized.
To put the program back at the factory-default, initialize the LCD TV using the following procedure.
[TYPE A]
1. Turn the power on.
2. Enter the service mode.
- To cancel the service mode, press [ ] button on
the remote control unit.
3. Press [BACK] button to enter the Control Panel
Key Confirmation Menu.
4. Press any button on the control panel.
5. Press [INFO] button to proceed with the self check
mode.
6. Make sure to confirm the “INITIALIZED : OK”
appears in the green screen.
7. Unplug the AC Cord and plug it back on again.
[TYPE B, C]
1. Turn the power on.
2. Enter the service mode.
- To cancel the service mode, press [ ] button on
the remote control unit.
3. Press [BACK] button to enter the Panel Key
Confirmation Menu.
4. Press any button on the control panel.
5. Press [INFO] button to proceed with the self check
mode.
6. Make sure to confirm the “INITIALIZED FINISH”
appears in the green screen.
7. Unplug the AC Cord and plug it back on again.
6-1 PL13.11_INT
Downloaded from www.Manualslib.com manuals search engine
FIRMWARE RENEWAL MODE
[TYPE A] Update file selection screen appears as follows.
(Files included in the USB storage device are
displayed.
Equipment Required "*" differs depending on the models.
1. USB storage device
Select an upgrade file *****_******.upg
2. Remote Control Unit
*****_******.upg
Firmware Update Procedure *****_******.upg
1. Turn the power off and unplug the AC Cord.
2. Insert the USB storage device to the USB port as
shown below.
Update procedure
1. Turn the power on. 11. The update will start and the following will appear
2. Press [MENU] button to display Menu. in the screen.
3. Select “Features”. "*" differs depending on the models.
5. Select “Upgrade” to display Upgrade screen. Software upgrade in progress. Please wait.
6. Press [OK] button to display Software Upgrade Do not remove the USB storage device or
screen. turn the TV off while upgrade is in progress.
7. Select “USB” and press [OK] button. Current Version: *******-***-*-***-****
8. Insert the USB storage device to the USB port as New Version: *******-***-*-***-****
shown below. *1 Downloading...
0%
Rear Cabinet
(example)
Note: If the above screen isn’t displayed, repeat from
step 1.
USB port
The appearance shown in *1 is described as follows.
Appearance State
Downloading the firmware from
USB storage Downloading...
device the USB storage device.
Writing the downloaded firmware
Writing...
in flash memory.
Checking... Checking the new firmware.
Software Upgrade
9. Select “Check” and press [OK] button.
10. Select “Upgrade” and press [OK] button to start
software upgrade.
7-2 PL13.11FW
Downloaded from www.Manualslib.com manuals search engine
Factory Upgrade (Firmware Upgrade/Flash Upgrade)
Firmware Upgrade
(Filename example: FACT_TVNB012_00_PF_XX91_BC.ecc or FACT_TVNB1012_00_PG_XX91_BA0.bin)
Upgrade the firmware and initialize the setting values.
The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to
upgrade the firmware and initialize the setting values also, add “FACT_” at the beginning of the filename.
If you want to upgrade the firmware only and leave the setting values as they are, eliminate the “FACT_” from the
filename.
Flash Upgrade
(Filename example: ALL_TVNB012_00_PF_XX91_BC.ecc or ALL_TVNB1012_00_PG_XX91_BA0.bin)
Upgrade the firmware and initialize the setting values along with the factory default such as White Balance, etc.
Before the upgrade, you will need to make a note of all the factory default so you will be able to set it back on the
TV after the initialization.
The Flash Upgrade will be done by it's unique file.
The User Upgrade/Firmware Upgrade (Factory Upgrade) file cannot be used for this upgrade.
Update procedure
1. Turn the power off. The appearance shown in *1 is described as follows.
2. Insert the USB storage device to the USB port as Appearance State
shown below.
Downloading the firmware from
Downloading...
Rear Cabinet the USB storage device.
(example)
Writing the downloaded firmware
Writing...
in flash memory.
USB port Checking... Checking the new firmware.
7-3 PL13.11FW
Downloaded from www.Manualslib.com manuals search engine
TROUBLESHOOTING
[Power Supply Section]
FLOW CHART NO.1
The power cannot be turned on.
No
Is the fuse (F602) normal? See FLOW CHART No.2 <The fuse blows out.>
Yes
Is normal state restored when once unplugged No Check if there is any leak or short-circuit on the
power cord is plugged again after several seconds? primary circuit component and repair it if defective.
Yes (C607, C612, D601, D602, D603, D604, D605, D606,
No D607A, D608, D609A, D621, D623, Q601, Q602,
Is the P-ON+21V line voltage normal?
Q621, R611, R619, T601)
Yes
Check if there is any leak or short-circuit on the Check if there is any leak or short-circuit on the
primary circuit component and repair it if defective. each rectifying circuit component of secondary side
and repair it if defective.
Make sure to repair the primary circuit component before replacing the fuse (F602).
Does the photocoupler circuit on the secondary side No Check IC602, D652, D654, D660, D661, Q653 and
operate normally? their periphery circuit. Repair it if defective.
Yes
Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side.
Repair it if defective. (D650, D651, D653, D655, D659, Q658, (IC651, Q657))
8-1 PL13.11ATR
Downloaded from www.Manualslib.com manuals search engine
FLOW CHART NO.5
P-ON+21V is not output.
Is approximately +21V voltage supplied to the cathode No Check D650, D651, D652, D659, C651, C652,
of D650(D651, D659)? C653, C667, C668 and their periphery circuit.
Yes Repair it if defective.
No
Is approximately +12V voltage supplied to the cathode Check D653, D654, D655, C654, C655 and their
of D653(D655)? periphery circuit. Repair it if defective.
Yes
No
Is approximately +12V voltage supplied to the emitter Check D653, D654, D655, C654, C655, R690 and
of Q658? their periphery circuit. Repair it if defective.
Yes
No
Is approximately +11V voltage supplied to the base of Check D662, Q656 and their periphery circuit.
Q658? Repair it if defective.
Yes
Replace Q658.
[TYPE B]
AL+3.3V is not output.
No
Is approximately +12V voltage supplied to Pin(3) of Check D653, D654, D655, C654, C655, R676, R678,
IC651? R679, R683, R684 and their periphery circuit.
Yes Repair it if defective.
Replace IC651
[TYPE C]
AL+3.3V is not output.
Replace IC651.
8-2 PL13.11ATR
Downloaded from www.Manualslib.com manuals search engine
[Video Signal Section]
FLOW CHART NO.1
The key operation is not functioning.
No
When touching each buttons, does the Pin(6) voltage Replace the Function CBA Unit.
of CN4052 decrease?
Yes
No
Is approximately +3.3V voltage supplied to Pin(1) of Check AL+3.3V line and repair it if defective.
CN4052?
Yes
No
Is the "L" pulse supplied to Pin(5) of CN4052 when the Replace the Function CBA Unit.
remote control unit is activated?
Yes
No
Is approximately +21V voltage supplied to See FLOW CHART NO.5 <P-ON+21V is not output.
Pin(20, 21, 22, 23) of CN501? [Power Supply Section]>
Yes
No
Is approximately +3.3V voltage supplied to Pin(8) of See FLOW CHART NO.7 <AL+3.3V is not output.
CN501? [Power Supply Section]>
Yes
8-3 PL13.11ATR
Downloaded from www.Manualslib.com manuals search engine
[Audio Signal Section]
FLOW CHART NO.1
Audio is not output normally.
No
Is approximately +12V voltage supplied to See FLOW CHART NO.6 <AMP+13V is not output.
Pin(15, 16, 17, 18) of CN501? [Power Supply Section]>
Yes
No
Is approximately +3.3V voltage supplied to Pin(8) of See FLOW CHART NO.7 <AL+3.3V is not output.
CN501? [Power Supply Section]>
Yes
No
Are the audio signals output to Pin(1, 2, 3, 4) of CN3801? Replace the Digital Main CBA Unit.
Yes
8-4 PL13.11ATR
Downloaded from www.Manualslib.com manuals search engine
IC3101
(MAIN MICRO CONTROLLER)
[TYPE A]
CN3706
TX(+)
AD6 TX(+)
TX(-)
ETHERNET AE6 TX(-) RS4051
JACK RX(+)
AC7 RX(+) REMOTE
RX(-)
AC8 RX(-) SENSOR
Y7 VGA-SCL
VGA-SDA
AD3 VGA-SDA
TO VIDEO/AUDIO LCD-P-ON
W2 LCD-P-ON
9-1
BLOCK DIAGRAM COMP-DET
H6 COMP-DET
HP-DET
L2 HP-DET
CN3601 CN501
PROTECT3
PROTECT3 T2 3 PROTECT3 3 TO
BACKLIGHT-SW
BACKLIGHT-SW W3 5 BACKLIGHT-SW 5 LED BACKLIGHT DRIVE
BACKLIGHT-ADJ BLOCK DIAGRAM
BACKLIGHT-ADJ P7 7 BACKLIGHT-ADJ 7
X3101
25MHz AE4 AXI
OSC AD4 AXO
PL13.11ABLS
VIDEO SIGNAL AUDIO SIGNAL
COMPONENT
-Pb-IN
COMPONENT
-Pr-IN
2. Video/Audio Block Diagram
TO DIGITAL
SIGNAL PROCESS
JK3706 BLOCK DIAGRAM
AUDIO(L)-IN
AUDIO(L)-IN AUDIO(R)-IN
9-2
AUDIO(R)-IN
Q3709
SPDIF
DIGITAL BUFFER
AUDIO-OUT
(COAXIAL)
HP(R)
JK3801 HP(L)
HEADPHONE
JACK
25 DRIVE AMP(L)-OUT
PWM POWER 3
LOGIC LIMIT
CN3801 23 DRIVE
SP3801 SP(L)+ 1
SPEAKER SP(L)- 2
L-CH 18 DRIVE AMP(R)-OUT
PWM POWER 12
SP(R)+ 4 LIMIT
LOGIC
SP(R)- 3 20 DRIVE VGA-SCL
Q3821
VGA-SDA
1 P-ON+3.3V
CONTROL LOGIC LCD-P-ON TO SYSTEM CONTROL
2
SP3802 COMP-DET BLOCK DIAGRAM
SPEAKER HP-DET
R-CH Q3822
PL13.11ABLVA
LCD PANEL
VIDEO SIGNAL AUDIO SIGNAL ASSEMBLY
9-3
3 AE24
CLOCK(+)
10 AD22
CLOCK(-)
12 AC22
HDMI-DATA
16 W6 IC3401
HDMI-CLOCK
3. Digital Signal Process Block Diagram
15 T7 (DDR3 SDRAM)
MMDQ(0-31)
JK3715 DATA(0-15)
DATA0(+) HDMI
7 W23 I/F ADDESS(0-14)
DATA0(-) MMA(0-14)
9 W22 IC3402
DATA1(+)
4 V23 HDMI SW (DDR3 SDRAM)
DATA1(-)
6 V22 DATA(16-31)
DATA2(+)
1 U23
HDMI-IN2 DATA2(-) ADDESS(0-14)
3 V24
CLOCK(+)
10 Y25
CLOCK(-) IC3102
12 Y24
HDMI-DATA (NAND FLASH MEMORY)
16 AA5
HDMI-CLOCK MMCDAT(0-7)
15 V7 VIDEO DATA(0-7)
DECODER
JK3716
DATA0(+)
7 AB24
DATA0(-)
9 AC25
DATA1(+)
4 AA23
DATA1(-)
6 AB25
DATA2(+)
1 Y23
HDMI-IN3 DATA2(-)
3 AA24
CLOCK(+)
10 AC24
CLOCK(-)
12 AD25
HDMI-DATA
16 AE3
HDMI-CLOCK
15 R9
DIGITAL MAIN CBA UNIT
PL13.11ABLD
LCD PANEL
ASSEMBLY
P-ON+21V
Q1001
IC1001
(LED BACKLIGHT DRIVER)
16 DRIVE 2
14 CONTROL
BACKLIGHT-SW DRIVE 3
TO 13 LOGIC
BACKLIGHT-ADJ
SYSTEM CONTROL 1
BLOCK DIAGRAM PROTECT3
24 DRIVE 5
CN1001
1 VLED1
3 ILED1
4 ILED2
5 ILED3
7 ILED4
9-4
8 ILED5
9 ILED6
4. LED Backlight Drive Block Diagram
11 VLED2
Q1002
IC1002
(LED BACKLIGHT DRIVER)
10 OVP
16 DRIVE 2
14 CONTROL
13 LOGIC DRIVE 3
1
24 DRIVE 5
PL13.11BLBD
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. NOTE:
CAUTION ! : For continued protection against risk of fire,
If Main Fuse (F602) is blown , check to see that all components in the power supply The voltage for parts in hot circuit is measured using
replace only with same type 2.5A, 250V fuse.
circuit are not defective before you connect the AC plug to the AC power supply. 2.5A 250V hot GND as a common terminal.
ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.
Otherwise it may cause some components in the power supply circuit to fail.
CN501 CN3601
AC601
AC CORD F602 L601 L602 D601- D604 T601 15-18 AMP+13V 15-18 AMP+13V
CN601 2.5A/250V 8 AL+3.3V 8 AL+3.3V
B LINE LINE BRIDGE 6 7 20-23 P-ON+21V 20-23 P-ON+21V
W FILTER FILTER RECTIFIER
9
Q650
RESET
4 10
2
5. Power Supply Block Diagram
11
9-5
1 12 P-ON+21V
Q601
SWITCHING
Q656, Q658
+3.3V REG.
Q621
OVER RESET TO
VOLTAGE P-ON-H2 SYSTEM CONTROL
PROTECT IC602 BLOCKDIAGRAM
ERROR
VOLTAGE DET
4 1
Q602
SWITCHING
3 2
CONTROL
Q653
HOT COLD
POWER SUPPLY CBA
PL13.11ABLP
RS4051
IC3005 REMOTE
[TYPE B]
CN3101 CN4052
CN3009 KEY-IN1 A15 4 KEY-IN1 6 KEY SWITCH
USBDN REMOTE C14 5 REMOTE 5
T10 USBDN
USB JACK USBDP LED1 D14 LED DRIVE 6 LED1 4 P-ON+5V
R10 USBDP
Q3501, Q3502 BUFFER 7 LIGHT 3
D4051
LIGHT A13 Q3010
POWER
IC4051
LIGHT
SENSOR
AUDIO-MUTE
C1 AUDIO-MUTE
COMP-DET
TO VIDEO/AUDIO N12 COMP-DET
HP-MUTE
BLOCK DIAGRAM G13 HP-MUTE
HP-DET
K16 HP-DET
1. System Control Block Diagram
9-6
SCL R12 4 SCL
SDA T12 3 SDA
AL+3.3V
IC3006 (MEMORY)
CN3701 CN501
P-ON-H2 TO
18 P-ON-H2 6 POWER SUPPLY
RESET
RESET J15 RESET 20 RESET 4 BLOCK DIAGRAM
IC3009
CN3701 CN501
PROTECT3
X3001 PROTECT3 B13 21 PROTECT3 3 TO
BACKLIGHT-SW
25MHz H15 XIN25 BACKLIGHT-SW E2 19 BACKLIGHT-SW 5 LED BACKLIGHT DRIVE
OSC BACKLIGHT-ADJ BLOCK DIAGRAM
H16 XOUT25 BACKLIGHT-ADJ F3 17 BACKLIGHT-ADJ 7
BACKLIGHT-SW TO
VIDEO/AUDIO
BLOCK DIAGRAM
PL13.11BBLS
VIDEO SIGNAL AUDIO SIGNAL
COMPONENT
-Pb-IN
COMPONENT
-Pr-IN
TO DIGITAL
2. Video/Audio Block Diagram
SIGNAL PROCESS
BLOCK DIAGRAM
JK3701
AUDIO(L)-IN
AUDIO(L)-IN AUDIO(R)-IN
9-7
AUDIO(R)-IN
Q3701
SPDIF
DIGITAL BUFFER
AUDIO-OUT
(COAXIAL)
IC3851
(HEADPHONE AMP)
6dB
JK3703 1 3
HEADPHONE 7 5
JACK 6dB
Q3861
MUTE 2
HP-DET
SP3802 Q3801 AUDIO-MUTE
1
SPEAKER CONTROL LOGIC Q3803 COMP-DET TO SYSTEM CONTROL
R-CH 2 BLOCK DIAGRAM
P-ON+5V HP-MUTE
Q3802 BACKLIGHT-SW
PL13.11BBLVA
VIDEO SIGNAL AUDIO SIGNAL
LCD PANEL
IC3005 (DIGITAL SIGNAL PROCESS)
ASSEMBLY
VGA-HSYNC
A14 HSYNC
VGA-VSYNC
B14 VSYNC
VGA-R-IN
C11
VGA-G-IN CN3013
A9
VGA-B-IN N16 24 RXO0(-)
C7
COM-VIDEO-Y/VIDEO-IN SW A/D N15 23 RXO0(+)
C9 CONVERTER
COM-VIDEO-Pb-IN P16 22 RXO1(-)
D8
COM-VIDEO-Pr-IN P15 21 RXO1(+)
B11
C10 LVDS TX R16 20 RXO2(-)
TO
VIDEO/AUDIO R15 19 RXO2(+)
BLOCK DIAGRAM DIF-OUT1 R14 14 RXO3(-)
A12 DEMODULATOR
DIF-OUT2 T14 13 RXO3(+)
B12 /MPEG DECODER
T16 17 RXOCLK(-)
IF-AGC
A16 IF-AGC T15 16 RXOCLK(+)
JK3004
HDMI-IN1 IC3018 (HDMI SW) AUDIO
DECODER
TMDS-D0(+)
7 42
TMDS-D0(-) DIGITAL
9 41 SIGNAL
TMDS-D1(+)
4 45 26 B4 PROCESS
TMDS-D1(-)
9-8
6 44 27 A4
TMDS-D2(+)
1 48 23 B3
TMDS-D2(-)
3 47 24 A3 HDMI
TMDS-CLOCK(+)
10 39 20 B2 I/F
TMDS-CLOCK(-)
3. Digital Signal Process Block Diagram
12 38 21 A2
HDMI-DATA
16 36 17 B1
HDMI-CLOCK
15 37 18 A1
2 SCL1 SCL2 15
3 SDA1 SDA2 14
10 SCL3 SCL0 7 G14 HDMI-SCL
11 SDA3 SDA0 6 F14 HDMI-SDA
TO VGA-SCL
VIDEO/AUDIO VGA-SDA DIGITAL MAIN CBA UNIT
BLOCK DIAGRAM
PL13.11BBLD
LCD PANEL
ASSEMBLY
P-ON+21V
Q1001
IC1001
(LED BACKLIGHT DRIVER)
16 DRIVE 2
14 CONTROL
BACKLIGHT-SW DRIVE 3
TO 13 LOGIC
BACKLIGHT-ADJ
SYSTEM CONTROL 1
BLOCK DIAGRAM PROTECT3
24 DRIVE 5
CN1001
1 VLED1
3 ILED1
4 ILED2
5 ILED3
7 ILED4
9-9
8 ILED5
9 ILED6
4. LED Backlight Drive Block Diagram
11 VLED2
Q1002
IC1002
(LED BACKLIGHT DRIVER)
10 OVP
16 DRIVE 2
14 CONTROL
13 LOGIC DRIVE 3
1
24 DRIVE 5
PL13.11BLBD
CAUTION !
NOTE:
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, The voltage for parts in hot circuit is measured using
If Main Fuse (F602) is blown , check to see that all components in the power supply replace only with same type 2.5A, 250V fuse. hot GND as a common terminal.
circuit are not defective before you connect the AC plug to the AC power supply. 2.5A 250V ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.
Otherwise it may cause some components in the power supply circuit to fail.
CN501 CN3701
AC601
AC CORD F602 L601 L602 D601- D604 T601 15-18 AMP+13V 6-9 AMP+13V
CN601 2.5A/250V 8 AL+3.3V 16 AL+3.3V
B LINE LINE BRIDGE 6 7 20-23 P-ON+21V 1-4 P-ON+21V
W FILTER FILTER RECTIFIER
9
Q650
RESET
4 10
2
5. Power Supply Block Diagram
11
1 12 P-ON+21V
9-10
Q601
SWITCHING
IC651
+3.3V REG.
Q621
OVER RESET TO
VOLTAGE P-ON-H2 SYSTEM CONTROL
PROTECT IC602 BLOCKDIAGRAM
ERROR
VOLTAGE DET
4 1
Q602
SWITCHING
3 2
CONTROL
Q653
HOT COLD
POWER SUPPLY CBA
PL13.11BBLP
IC3001
(MAIN MICRO CONTROLLER)
[TYPE C]
RS4051
REMOTE
SENSOR
CN3009
USB(-) CN3101 CN4052
194 USB(-) KEY-IN1 210 4 KEY-IN1 6 KEY SWITCH
USB JACK USB(+)
195 USB(+) REMOTE 215 5 REMOTE 5
Q3501, Q3502
LED1 205 LED DRIVE 6 LED1 4 P-ON+5V
LIGHT 208 BUFFER 7 LIGHT 3
D4051
Q3010
POWER
IC4051
LIGHT
VGA-SCL
1. System Control Block Diagram
212 VGA-SCL
VGA-SDA
TO VIDEO/AUDIO 213 VGA-SDA
AMP-MUTE
BLOCK DIAGRAM 127 AMP-MUTE
9-11
COMP-DET
133 COMP-DET AL+3.3V Q3605
PROTECT3 134
PL13.11CBLS
VIDEO SIGNAL AUDIO SIGNAL
COMPONENT
-Pb-IN
COMPONENT
-Pr-IN
TO DIGITAL
2. Video/Audio Block Diagram
SIGNAL PROCESS
JK3701 BLOCK DIAGRAM
AUDIO(L)-IN
AUDIO(L)-IN AUDIO(R)-IN
AUDIO(R)-IN
9-12
Q3701
SPDIF
DIGITAL BUFFER
AUDIO-OUT
(COAXIAL)
HP(R)
JK3703 HP(L)
HEADPHONE
JACK
25 DRIVE AMP(L)-OUT
PWM POWER 3
LOGIC LIMIT
CN3801 23 DRIVE
SP3801 SP(L)+ 1
SPEAKER SP(L)- 2
L-CH 18 DRIVE AMP(R)-OUT
PWM POWER 12
SP(R)+ 4 LIMIT
LOGIC
SP(R)- 3 20 DRIVE VGA-SCL
VGA-SDA
1 TO SYSTEM CONTROL
CONTROL LOGIC AMP-MUTE
2 BLOCK DIAGRAM
SP3802 COMP-DET
SPEAKER
R-CH Q3801
PL13.11CBLVA
LCD PANEL
VIDEO SIGNAL AUDIO SIGNAL ASSEMBLY
IC3001 (DIGITAL SIGNAL PROCESS)
VGA-HSYNC
26 VGA-HSYNC
VGA-VSYNC
32 VGA-VSYNC CN3013
VGA-R-IN
31 107 24 LVDS-OD0(-)
VGA-G-IN
29 108 23 LVDS-OD0(+)
VGA-B-IN A/D
27 105 22 LVDS-OD1(-)
COM-VIDEO-Y/VIDEO-IN CONVERTER
36 SW 106 21 LVDS-OD1(+)
COM-VIDEO-Pb-IN
34 103 20 LVDS-OD2(-)
COM-VIDEO-Pr-IN
38 104 19 LVDS-OD2(+)
35 99 14 LVDS-OD3(-)
DIF-OUT1
TO VIDEO/AUDIO 70 DEMODULATOR 100 13 LVDS-OD3(+)
DIF-OUT2
BLOCK DIAGRAM 71 /MPEG DECODER 101 17 LVDS-OCLK(-)
IF-AGC
74 IF-AGC LVDS 102 16 LVDS-OCLK(+)
TX
9-13
CLOCK(+)
10 3
CLOCK(-)
12 2
HDMI-DATA
16 6 IC3002
HDMI-CLOCK
3. Digital Signal Process Block Diagram
PL13.11CBLD
LCD PANEL
ASSEMBLY
P-ON+21V
Q1001
IC1001
(LED BACKLIGHT DRIVER)
16 DRIVE 2
14 CONTROL
BACKLIGHT-SW DRIVE 3
TO 13 LOGIC
BACKLIGHT-ADJ
SYSTEM CONTROL 1
BLOCK DIAGRAM PROTECT3
24 DRIVE 5
CN1001
1 VLED1
3 ILED1
4 ILED2
5 ILED3
7 ILED4
9-14
8 ILED5
9 ILED6
4. LED Backlight Drive Block Diagram
11 VLED2
Q1002
IC1002
(LED BACKLIGHT DRIVER)
10 OVP
16 DRIVE 2
14 CONTROL
13 LOGIC DRIVE 3
1
24 DRIVE 5
PL13.11BLBD
CAUTION !
NOTE:
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, The voltage for parts in hot circuit is measured using
If Main Fuse (F602) is blown , check to see that all components in the power supply replace only with same type 2.5A, 250V fuse. hot GND as a common terminal.
circuit are not defective before you connect the AC plug to the AC power supply. 2.5A 250V ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.
Otherwise it may cause some components in the power supply circuit to fail.
CN501 CN3602
AC601
AC CORD F602 L601 L602 D601- D604 T601 15-18 AMP+13V 15-18 AMP+13V
CN601 2.5A/250V 8 AL+3.3V 8 AL+3.3V
B LINE LINE BRIDGE 6 7 20-23 P-ON+21V 20-23 P-ON+21V
W FILTER FILTER RECTIFIER
9
Q650
RESET
4 10
2
5. Power Supply Block Diagram
11
1 12 P-ON+21V
9-15
Q601
SWITCHING
IC651, Q657
+3.3V REG.
Q621
OVER RESET TO
VOLTAGE P-ON-H2 SYSTEM CONTROL
PROTECT IC602 BLOCKDIAGRAM
ERROR
VOLTAGE DET
4 1
Q602
SWITCHING
3 2
CONTROL
Q653
HOT COLD
POWER SUPPLY CBA
PL13.11CBLP
SCHEMATIC DIAGRAMS / CBA AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis
have special characteristics. These characteristics
often pass unnoticed and the protection afforded by
them cannot necessarily be obtained by using
replacement components rated for higher voltage,
wattage, etc. Replacement parts that have these
special safety characteristics are identified in this
manual and its supplements; electrical components
having such features are identified by the mark “#” in
the schematic diagram and the parts list. Before
replacing any of these components, read the parts list
in this manual carefully. The use of substitute
replacement parts that do not have the same safety
characteristics as specified in the parts list may create
shock, fire, or other hazards.
Notes:
1. Do not use the part number shown on these
drawings for ordering. The correct part number is
shown in the parts list, and may be slightly
different or amended since these drawings were
prepared.
2. All resistance values are indicated in ohms
(K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless
otherwise specified.
4. All capacitance values are indicated in μF
(P = 10-6 μF).
5. All voltages are DC voltages unless otherwise
specified.
6. This schematic diagrams are masterized version
that should cover the entire PL13.11 chassis
models.
Thus some parts in detail illustrated on this
schematic diagrams may vary depend on the
model within the PL13.11 chassis.
Please refer to the parts lists for each models.
7. The Circuit Board layout illustrated on this service
manual is the latest version for this chassis at the
moment of making this service manual.
Depend on the mass production date of each
model, the actual layout of each Board may differ
slightly from this version.
10-1 PL13.11SC
Downloaded from www.Manualslib.com manuals search engine
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON
THE FOLLOWING PAGES:
1. CAUTION:
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME
TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F602) is blown, first check to see that all components in the power supply circuit are not
defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components
in the power supply circuit to fail.
3. Note:
1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.
1 2 3
(Unit: Volt) 5.0 5.0 Power on mode
10-2 PL13.11SC
Downloaded from www.Manualslib.com manuals search engine
Power Supply 1 Schematic Diagram
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, NOTE:
If Main Fuse (F602) is blown , check to see that all components in the power supply replace only with same type 2.5A, 250V fuse. The voltage for parts in hot circuit is measured using
circuit are not defective before you connect the AC plug to the AC power supply. 2.5A 250V hot GND as a common terminal.
ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.
Otherwise it may cause some components in the power supply circuit to fail.
4 AC CORD CN601
W
B
F602 R601
1.2M/1/2W
2.5A/250V
C603 OPEN
SA601
VARISTOR
C602
2200P/250V
2.5A250V C604
0.22/310V
C616 OPEN
L601 JS609
LINE FILTER
JS601 JS602 JS603
OPEN OPEN
JS604 D655
SB3A0BH
C614 R610
0.22/310V D601 D604 OPEN
1N5406BH 1N5406BH D655A
OPEN
R602
OPEN D653
L602 SB3A0BH
JS605 LINE FILTER JS606
OPEN OPEN D602 D603 D653A
OPEN
3 1N5406BH 1N5406BH
2 0
Q621
KTC3875S
D621
1SS400 D610
1SS400
D659
SB3150BH
470/25V 470/25V 470/25V 470/25V 470/25V 1ZB30BB OPEN
C701
OPEN
R702
OPEN
Q701
OPEN
R688 R689
Q657
2SA950-O
(+3.3V REG.) R685 R686 R687
D405
OPEN TO DIGITAL MAIN
-Y-RTK/P D659A 2.2 2.7 CBA UNIT CN3601
D607A D607 R613 OPEN 11.2 3.3 3.3 3.3 3.3 CN501 or CN3602 or CN3701
TFZVTR27B OPEN OVER 270 D406 0 1 LED-CONT(NU)
VOLTAGE IC651 OPEN
0.4 PROTECT R621 D623 Q657A 10.6 AP1117E33G-13 0 2 PROTECT1
560 MM5Z30B OPEN (+3.3V REG.)
0 C633 3.4 3 PROTECT3
R622 C623 OPEN
0 3.3 4
GND
OUT
0 4.7 RESET
IN
1 BC603
BEAD
3.3K
Q653
KTC3875S-Y-RTK/P
0
0.7
R669
10K
R670
270
R671
270
R672
270
Q656
KTC3875S
3.9 -Y-RTK/P
(SWITCHING)
R662
3.3K
R680
100
OPEN OPEN 12.1 17
12.1 18
0 19
AMP+13V
AMP+13V
GND
C665 R682 21.1 20 P-ON+21V
BC604 (SWITCHING) 0 R668 0.1 0
BEAD 47K C639 21.1 21 P-ON+21V
3.9 OPEN
2.5 21.1 22 P-ON+21V
D662
0 SL431A-AT 21.1 23
HOT COLD R681
10K
P-ON+21V
A B C D E F G
10-3 PL13.11SCP1
C1026
220P/500V
CONTINUE
D1001 L1001 POWER 1
SK210TD 22uH
P-ON+21V
R1006 10K
4 R1034
510K
R1035
430K
C1008 C1010
47/100V 47/100V
C1018
1/100V
C1014
1/100V
C1012
OPEN R1005 1K
C1001
330/25V
C1002 C1003
330/25V 1
C1004
1
C1005
OPEN
C1006
1
R1009 R1008
10K
BACKLIGHT-ADJ
PROTECT3
BACKLIGHT-SW
3 NU
VLED2
10
11 49.2
C1037
1000P
1.4 10 OVP
1.3 11 ISET CONTROL
LOGIC
15 0
14 0.1
C1041
4.7
R1028 1.0 12 RT
0 13 2.9
R1027 R1030 C1020
12K 100K OPEN
C1027
220P/500V
D1002 L1002
SK210TD 22uH
2 R1039
27K
IC1002
HA7209PC
LED BACKLIGHT
DRIVER
0
D1004
1SS400
20.8 D
R1040 R1011 Q1002
3.0 1 0 10
24 3.3 2.9
G AP18T10AGH-HF
(SWITCHING)
R1024 C1025
0 0.5 2 DRIVE NU 23 OPEN R1013 D1006 0.1 S
R1042 C1044 OPEN
D1024 C1034 100 1 200
OPEN OPEN 0.6 3 DRIVE COMP 22 1.5
R1025 C1040 C1023 R1016 R1019
0 0 4 1000P OPEN 0.18/2W
DRIVE MCP 21 0 OPEN R1051 D1051
OPEN OPEN R1017
D1025 C1035 0.6 5 DRIVE SEL 20 5.1 OPEN
OPEN OPEN R1004 R1003
R1026 0 6 GND 360 360
0 VIN 19 18.2
0 7 C1017 R1053
D1026 C1036 DRIVE GND 18 0 0.1 OPEN
OPEN OPEN
0 8 DRIVE DRIVE LDO 17 5.1
0 9 DRIVE 16 2.9
1.4 10 OVP C1042
15 0 4.7
C1038 1.3 11 ISET CONTROL 14 0.1
1000P LOGIC
1 R1033
0
R1032
12K
R1031
100K
1.0 12 RT 13 2.9
C1021
OPEN
R1047
0
H I J K L M
10-4 PL13.11SCP2
2 D4051
SMLE12WBC7W1HR
POWER
IC4051
PH5502B2NA1-E4
R4055
OPEN
R4059
OPEN
3
4
5
LIGHT
LED1
REMOTE
6 KEY-IN1
(LIGHT SENSOR)
7 GND
1 OUT NU 6 8 SCL(NU)
RS4051 R4057 2 GND NU 5 9 SDA(NU)
RS-272 27K
(REMOTE SENSOR) 3 VCC NU 4
C4057 R4058 R4056
VOUT
1 R4001
18K
R4002
8.2K
R4003
4.7K
R4004
2.7K
R4005
2.2K
R4006
2.2K
D4002 D4001 C4002
OPEN SW4001 SW4002 SW4003 SW4004 SW4005 SW4006 SW4007 MM5Z5V6B 0.1
VOL VOL CH CH UP MENU SOURCE POWER
DOWN UP DOWN
A B C
10-5 PL13.11SCF
4 NU 10
GND 11
LVDS-OD0(-) 12
R3910
OPEN 27
26
25
VCOM
PWR-CTRL
P-ON+3.3V
LVDS-OD0(+) 13 24 GND
GND 14 23 LVDS-OD0(-)
LVDS-OD1(-) 15 22 LVDS-OD0(+)
LVDS-OD1(+) 16 21 LVDS-OD1(-)
GND 17 20 LVDS-OD1(+)
LVDS-OD2(-) 18 19 LVDS-OD2(-)
LVDS-OD2(+) 19 18 LVDS-OD2(+)
GND 20 17 GND
LVDS-OCLK(-) 21 16 LVDS-OCLK(-)
LVDS-OCLK(+) 22 15 LVDS-OCLK(+)
GND 23 14 GND
LVDS-OD3(-) 24 13 LVDS-OD3(-)
LVDS-OD3(+) 25 12 LVDS-OD3(+)
GND 26 R3908 11 LVDS-OD4(-)
OPEN R3932
BIST 27 12K 10 LVDS-OD4(+)
PANEL-SCL 28 R3907 9 LVDS-OD5(-)
OPEN
PANEL-SDA 29 R3934 8 LVDS-OD5(+)
3.9K
GND 30 7 GND
CONTINUE R3931 R3933 C3947 C3948 6 TP
DIGITAL 2 11K 12K 47/25V 0.1
LVDS-OD4(+) R3935 5 POL
1K
3 LVDS-OD4(-)
LVDS-OD3(+)
LVDS-OD3(-)
R3924
OPEN
Q3901
2SC4081UBTLQ
(DRIVE)
4
3
2
1
CPV
OE1
OE2
STV
LVDS-OCLK(+)
LVDS-OCLK(-)
LVDS-OD2(+)
LVDS-OD2(-)
CN3903 (NO CONNECTION)
LVDS-OD1(+) 31 LCD+21V
LVDS-OD1(-) 30 LCD+21V
LVDS-OD0(+) 29 LCD+21V
LVDS-OD0(-) 28 GND
LVDS-ED4(+) *1
IC3101(1/7) 27 VCOM
LVDS-ED4(-) MN2WS0270EA 26 PWR-CTRL
LVDS-ED3(+) DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER 25 P-ON+3.3V
LVDS-ED3(-) R3916 24 GND
R3913 OPEN 10K
LVDS-ECLK(+) L3 23 LVDS-OD0(-)
LVDS-ECLK(-) L4 22 LVDS-OD0(+)
LVDS-ED2(+) J6 K3 21 LVDS-OD1(-)
LVDS-ED2(-) K6 K4 20 LVDS-OD1(+)
LVDS-ED1(+) J5 19 LVDS-OD2(-)
LVDS-ED1(-) R3914 OPEN
K5 J1 18 LVDS-OD2(+)
LVDS-ED0(+) L7 J2 17 GND
LVDS-ED0(-) LVDS
M7 TX J3 16 LVDS-OCLK(-)
H3
R3915 OPEN
15
14
13
LVDS-OCLK(+)
GND
LVDS-OD3(-)
LCD+12V 28 N5 H4 12 LVDS-OD3(+)
LCD+12V 27 M5 G3 11 LVDS-OD4(-)
GND 26 M6 F3 10 LVDS-OD4(+)
GND 25 F1 9 LVDS-OD5(-)
OPEN
OPEN
GND 24 K7 NU F2 8 LVDS-OD5(+)
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
PANEL-WP 23 J7 NU NU P1 7 GND
R3974 OPEN
C3916
C3903
C3904
C3905
C3908
C3911
C3906
C3907
C3912
C3913
C3914
C3915
LVDS-SEL 22 TP R6 6 TP
R3975 OPEN
NU 21 TO DIGITAL POL R3 5 POL
MAIN 6 R3976 OPEN
GND 20 IC3101(5/7) CPV P3 4 CPV
R3977 OPEN
LVDS-OD0(-) 19 OE N3 3 OE
R3978 OPEN
LVDS-OD0(+) 18 OE2 R5 2 OE2
R3979 OPEN
GND 17 STV P4 1 STV
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
LVDS-OD1(-) 16
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
LVDS-OD1(+) 15 CONTINUE
DIGITAL 4
R3884
R3928
R3883
R3882
R3881
R3880
C3928
C3917
C3918
C3919
C3922
C3923
C3920
C3921
C3924
C3925
C3926
C3927
C3942
C3998
C3941
C3940
C3939
C3938
GND 14
LVDS-OD2(-) 13 VCOM-PWM
LVDS-OD2(+) 12
GND 11 N2 NU CONTINUE
P2 NU DIGITAL 2
LVDS-OCLK(-) 10 VCOM-DC
1 LVDS-OCLK(+) 9
GND 8
LVDS-OD3(-) 7
R3901
10K
P7 BACKLIGHT-ADJ
VCOM-PWM
LCD-P-ON
PANEL-WP
LVDS-OD3(+) 6 PANEL-SCL
GND 5 PANEL-SDA
NU 4
R3906 OPEN
PANEL-SCL 3 CN3902 (NO CONNECTION)
R3904 OPEN
PANEL-SDA 2 1 GND
GND 1 2 PANEL-WP
R3925 3 PANEL-SCL
CONTINUE OPEN
DIGITAL 7
BACKLIGHT-ADJ DIGITAL MAIN CBA UNIT 4 PANEL-SDA
A B C D E F
10-6 PL13.11ASCD1
CONTINUE
DIGITAL 7
P-ON+21V
P-ON+3.3V R3942
0
CONTINUE
DIGITAL 2 R3952 D3905 Q3905
OPEN OPEN
4 LCD+12V/+21V
D3906
OPEN
R3550 IC3901
C3996
OPEN
R3899
1
2
OPEN
8
7
OPEN OPEN OPEN
C3946 3 6
OPEN
1 SS BST 8 R3897 4 5
C3949 OPEN
OPEN
2 EN IN 7 R3891
TO LCD PANEL C3951 C3945 C3944 C3943 OPEN
ASSEMBLY CN3906 R3990 OPEN OPEN OPEN OPEN
OPEN 3 COMP SW 6 R3895
NU 1 OPEN
C3992 C3991 Q3904
NU 2 OPEN OPEN 4 FB GND 5 OPEN
C3950 R3898 C3997
NU 3 OPEN R3938 OPEN OPEN
C3955 R3937 OPEN
NU 4 OPEN R3936 OPEN R3939
OPEN OPEN L3901
NU 5 OPEN
GND 6 CONTINUE
DIGITAL 6
GND 7 R3912 R3911 C3959 C3958 C3952 D3901 C3954 C3956 C3953 P-ON-H2
GND 8 OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN
R3989 0
GND 9
R3988 0
GND 10
R3981 OPEN
LVDS-OD4(+) 11
R3980 OPEN
LVDS-OD4(-) 12
R3943 0
3 LVDS-OD3(+)
LVDS-OD3(-)
GND
13
14
15
R3921 0
CONTINUE
LVDS-OCLK(+) 16 DIGITAL 1
R3920 0x4
LVDS-OCLK(-) 17 LVDS-OD4(+)
GND 18 LVDS-OD4(-)
LVDS-OD2(+) 19 LVDS-OD3(+)
LVDS-OD2(-) 20 LVDS-OD3(-)
R3919 0x4
LVDS-OD1(+) 21 LVDS-OCLK(+)
LVDS-OD1(-) 22 LVDS-OCLK(-)
LVDS-OD0(+) 23 LVDS-OD2(+)
LVDS-OD0(-) 24 LVDS-OD2(-)
R3987 0
GND 25 LVDS-OD1(+)
R3986 0
GND 26 LVDS-OD1(-)
R3985 OPEN
LVDS-ED4(+) 27 LVDS-OD0(+)
R3984 OPEN
LVDS-ED4(-) 28 LVDS-OD0(-)
LVDS-ED3(+) 29 LVDS-ED4(+)
LVDS-ED3(-) 30 LVDS-ED4(-)
GND 31 LVDS-ED3(+)
LVDS-ECLK(+) 32 LVDS-ED3(-)
2 LVDS-ECLK(-)
GND
LVDS-ED2(+)
33
34
35
LVDS-ECLK(+)
LVDS-ECLK(-)
LVDS-ED2(+)
LVDS-ED2(-) 36 LVDS-ED2(-)
LVDS-ED1(+) 37 LVDS-ED1(+)
LVDS-ED1(-) 38 LVDS-ED1(-)
LVDS-ED0(+) 39 LVDS-ED0(+)
LVDS-ED0(-) 40 LVDS-ED0(-)
GND 41
R3866 0
GND 42
R3867 0 CONTINUE
P-ON+3.3V 43 DIGITAL 1
R3922 0 C3902 R3896 R3900 0
P-ON+3.3V 44 OPEN OPEN VCOM-DC
R3903 OPEN
VCOM 45 VCOM-PWM
R3905 100
LCD-P-ON 46 LCD-P-ON
R3869 0 R3941 R3940 C3909 C3910
GND 47 OPEN OPEN OPEN OPEN PANEL-WP
R3926 0
LCD+21V 48 PANEL-SCL
R3923 0
LCD+21V 49 D3902 PANEL-SDA
R3902 0 1SS400
LCD+21V 50
GND 51 C3901
R3982 0 4.7
CONTINUE
1 R3983 OPEN
R3918 OPEN
R3917 OPEN
DIGITAL 8
PROTECT3
G H I J K L
10-7 PL13.11ASCD2
*1
IC3101(2/7)
MN2WS0270EA
MAIN MICRO CONTROLLER
/DIGITAL SIGNAL PROCESS DIGITAL MAIN CBA UNIT CONTINUE
R3433 10K DIGITAL 7
DDRPWRON T5 AL+3.3V
R3421 270
MMVREF0 D3 VCC+1.5V
R3423 270
MMVREF1 D16
R3411 270 IC3401 IC3402
MMVREF2 D6
K4B1G1646G-BCH9 K4B1G1646G-BCH9
MMDQ0 (DDR3 SDRAM) (DDR3 SDRAM)
MMDQ0 D7
0.1
270
0.1
270
0.1
270
MMDQ1 E6 MMDQ1
3 MMDQ25
MMDQ26
MMDQ27
A17
D15
C15
MMDQ25
MMDQ26
MMDQ27
MMDQ28
MMDQ11
MMDQ14
A3
B8
DQU7
DQU6
VSS1
VSS2
A9
B3
MMDQ19
MMDQ22
A3
B8
DQU7
DQU6
VSS1
VSS2
A9
B3
MMDQ28 B12 MMDQ10 MMDQ18
MMDQ29 A12 MMDQ29 A2 DQU5 VSS3 E1 A2 DQU5 VSS3 E1
MMDQ30 MMDQ12 A7 DQU4 VSS4 G8 MMDQ20 A7 DQU4 VSS4 G8
MMDQ30 D11 MMDQ8 MMDQ16
MMDQ31 C11 MMDQ31 C2 DQU3 VSS5 J2 C2 DQU3 VSS5 J2
MMDQ15 C8 DQU2 VSS6 J8 MMDQ23 C8 DQU2 VSS6 J8
MMDQS1 B4 MMDQ9 C3 DQU1 VSS7 M1 MMDQ17 C3 DQU1 VSS7 M1
MMXDQS1 A4 MMDQ13 D7 DQU0 VSS8 M9 MMDQ21 D7 DQU0 VSS8 M9
MMDQS0 A6 MMDQ6 H7 DQL7 VSS9 P1 MMDQ30 H7 DQL7 VSS9 P1
MMXDQS0 C6 MMDQ2 G2 DQL6 VSS10 P9 MMDQ26 G2 DQL6 VSS10 P9
MMDQS3 D17 MMDQ7 H8 DQL5 VSS11 T1 MMDQ31 H8 DQL5 VSS11 T1
MMXDQS3 C16 MMDQ3 H3 DQL4 VSS12 T9 MMDQ27 H3 DQL4 VSS12 T9
MMDQS2 B15 MMDQ4 F8 DQL3 VSSQ1 B1 MMDQ28 F8 DQL3 VSSQ1 B1
MMXDQS2 C14 MMDQ1 F2 DQL2 VSSQ2 B9 MMDQ25 F2 DQL2 VSSQ2 B9
MMDQ5 F7 DQL1 VSSQ3 D1 MMDQ29 F7 DQL1 VSSQ3 D1
MMDM1 C9 MMDQ0 MMDQ24
MMDM0 B2 E3 DQL0 VSSQ4 D8 E3 DQL0 VSSQ4 D8
MMDM3 C12 VSSQ5 E2 VSSQ5 E2
MMDM2 C19 VSSQ6 E8 VSSQ6 E8
L2 CS# VSSQ7 F9 L2 CS# VSSQ7 F9
R3405 56x4 MMA2 K3 CAS# K3 CAS#
MMA2 G11 VSSQ8 G1 R3403 C3403 VSSQ8 G1 R3401 C3401
MMA6 K1 ODT OPEN OPEN K1 ODT OPEN OPEN
MMA6 E8 VSSQ9 G9 VSSQ9 G9
MMA8 G8 MMA8 J3 RAS# R3427 J3 RAS# R3431
2 MMA14
MMA9
MMA11
E7
E19
F18
R3406 56x4
MMA14
MMA9
MMA11
R3428
L3
T2
L8
WE#
RESET#
ZQ
CK J7
CK# K7
CKE K9
220
R3404
OPEN
C3404
OPEN
R3432
L3
T2
L8
WE#
RESET#
ZQ
CK J7
CK# K7
CKE K9
220
R3402
OPEN
C3402
OPEN
R3409 56x4
MMBA2 G16
MMBA0 E15
MMXWE D14
MMXCAS E14
MMCK B10
MMXCK B9
R3418 56
MMXCS1 D12
R3417 56
MMXCS0 E11
R3416 56
MMODT0 F11
1 MEMORY
I/F MMODT1
MMCKE0
MMCKE1
F12
F10
G10
R3415
R3414
R3413
R3412
56
56
56
56
MMXRAS F14
MMXRESET F19
TO DIGITAL C3405 1
MAIN 6 DDR3VOUT D1 R3419 C3407
IC3101(5/7) R3420 240 10K OPEN
MMZQ D4
NU G7
NU G12
M N O P Q R
10-8 PL13.11ASCD3
*1
IC3101(3/7)
MN2WS0270EA
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER C3125 C3126
0.1 0.1
4 CONTINUE
C3128
15P
C3124
X3101
25MHz
R3170
R3169
OPEN
AE4 AXI
10K
10K
10K
10K
COMP-DET H6 COMP-DET MMCDAT5 E20
MMCDAT6 4 NU NU 45 R3192
HP-DET G4 NU MMCDAT6 B20 56x4
R3132
R3121
R3124
R3173
R3111 R3112 M3 NU MMCDAT7 C20 MMCDAT7 5 NU I/O7 44 MMCDAT7
10K 100
L2 HP-DET MMCDAT6
6 NU I/O6 43
D20 NU
R3205 22 MMCDAT5
A20 NU NANDRYBY D22 7 R/B I/O5 42
R3201 75
W20 NU NFALE B23 MMCDAT4
R3202 75 8 RE I/O4 41
V20 NU NFCLE C23
R3203 75
Y22 NU TO DIGITAL XNFCE A23 9 CE NU 40
MAIN 6 R3190 75
CONTINUE AA22 NU IC3104(5/7) XNFWE A24
DIGITAL 7 R3189 75 10 NU NU 39
AB23 NU XNFWP B24
P-ON+3.3V R3208 R3204 75
OPEN W21 NU XNFRE E21 11 NU NU 38
P-ON+5V U20 NU NU C22
3 12 VCC VCC 37
R3128 10K
R3123 10K
AL+3.3V V21 NU NU F20
R3135
OPEN Y21 NU NU J24 13 VSS VSS 36
U19 NU NU J22
14 NU NU 35
W19 NU NU G24
V19 NU NU G23 15 NU NU 34
AB22 NU NU H23
(NO CONNECTION) CN3104 16 CLE NU 33 R3191
GND 10 U21 NU NU G22 56x4
NU H22 17 ALE I/O3 32 MMCDAT3
NU 9
EJTCK 8 AA7 NU NU K22 MMCDAT2
18 WE I/O2 31
JTDI 7 U9 NU NU J25
NU P22 19 WP I/O1 30 MMCDAT1
JTDO 6 AD8 NU
JTMS 5 AB7 NU NU P25 MMCDAT0
20 NU I/O0 29
TRSTN 4 Y8 NU NU R20
R3127 OPEN NU T21 21 NU NU 28
EVTRG 3 L21 NU
XRST 2 AC5 NU NU R22
22 NU NU 27
AL+3.3V 1 R3136 R3129
R3113 100 R3210 NU R21
10K 10K R3198 10K OPEN NU T20 23 NU NU 26
R3125 OPEN E24 NU NU T19
24 NU NU 25
G21 NU NU R19
CONTINUE
DIGITAL 8 R3130 E23 NU NU P24
2 STB-RESET
STMTIME1
OPEN
R3126
OPEN
D25
C25
D24
NU
NU
NU
NU
NU
NU
P21
AB18
Y18
J19 NU NU Y17
H19 NU NU W17
L20 NU NU W15
J23 NU NU AA17
L19 NU NU W18
N20 NU NU AC19
K19 NU NU Y16
N21 NU NU AD19
M20 NU NU W16
M19 NU NU Y20
J20 NU NU AB19
P20 NU NU AE20
K21 NU NU AB20
N19 NU NU AA18
R3224 1K
P19 NU NU AD20
R3115 OPEN
M21 NU NU AA21
F25 NU NU Y19
1 R3116 OPEN
R3118 1K
R3122 OPEN
H20
F23
F24
NU
NU
NU
NU
NU
NU
AA19
AA20
AC20
F22 NU
H21 NU
K20 NU
S T U V W X
10-9 PL13.11ASCD4
CONTINUE
DIGITAL 7
P-ON+5V TU3001
TUNER UNIT
P-ON+3.3V
DIF-OUT1
DIF-OUT2
IF-AGC
+3.3V
*1
GND
SDA
SCL
IC3101(4/7)
MN2WS0270EA 1 2 3 4 5 6 7
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
CONTINUE M1 NU L3005
DIGITAL 8 2.2uH
UART1TX N4 NU
M2 NU C3041 C3040 C3039 D3007
UART1RX NU AB9 OPEN 10 OPEN MM5Z5V6B
P5 NU NU AC9
R3193 100
F21 UART1RX NU Y12
R3194 100
G20 UART1TX NU AA15 C3002 D3001
R3217 1K OPEN OPEN
(NO CONNECTION) CN3101 B25 NU NU W14
GND 4 D23 NU NU W10
R3176 100
UARTORX 3 C24 UART0TX NU Y13
R3175 100 C3003 D3002
UARTOTX 2 E22 UARTOTX NU W8 OPEN OPEN
P-ON+5V 1 NU AA8
C3115 C3116 R3101 C3117 R3108 C3011 L3003 R3005
OPEN OPEN 10K OPEN OPEN 0.1 3.3uH 270
AD9
3 (USB JACK)
USB+5V
USB0(-)
CN3704
1
2
L3706
OPEN
N22 USB0(-)
DEMODULATOR
/MPEG
DECODER
AE9
C3026
OPEN C3014
C3027
0.1
C3013
39P L3004
3.3uH
R3003
270
2 USB1(-)
USB1(+)
GND
3
2
1
R3735
M22 USB1(-)
L23 USB1(+)
NU U10
RX(-) AC8
R7
R6
R5
NU
RX(-)
RCT
OPEN RX(+) AC7 R4 RX(+)
R3734 R3736 TX(-) AE6 R3 TX(-)
0 0 R3180 10K
WIRELESS M23 USB10D R2 TCT
LAN MODULE CN3701
USB1(+) 1 TX(+) AD6 R1 TX(+)
IC3702 C3744 C3701
USB1(-) 2 OPEN 0.01 0.01
USB+5V 3 1 VOUT VIN 5
GND 4 C3716 C3715
OPEN 2 GND OPEN
GND 5
GND 6 3 /FLAG EN 4 M25 USB1VBUS
R3704 C3714
OPEN OPEN CONTINUE
DIGITAL 7
R3702 CTRL11 AC6 CTRL11
OPEN
C3129
1
1
DIGITAL MAIN CBA UNIT
Y Z AA AB AC AD
10-10 PL13.11ASCD5
*1
DIGITAL MAIN CBA UNIT IC3101(5/7)
MN2WS0270EA
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
JK3701
COMPONENT-Y AE12 NU
/VIDEO-IN C3705 D3705 R3166 AC12 NU
39P OPEN 75
AD12 NU A/D
Y9 NU CONVERTER
COMPONENT
-Pb-IN C3770 D3701 R3163 Y10 NU
39P OPEN 75
AA9 NU
4 CONTINUE
DIGITAL 4
COMPONENT
-Pr-IN C3703
39P
D3704
OPEN
R3164
75
C3121
C3118
C3119
1
1
1
R3214
R3216
R3218
10
10
10
AC10 NU
AB10
AD11 TO DIGITAL
C3706 AB11 MAIN 3
COMP-DET 0.01 R3727 R3723 C3120 1 R3219 10 SW IC3101(2/7)
R3741 10K C3704 AC11
HP-DET C3720 100 1
33 100P C3109 1 R3220 100
Q3709 AD13
C3709 R3725 2SC4081UBTLQ R3724 C3113 1 R3221 100 TO DIGITAL
JK3706 1 220 10K AB13 MAIN 4
DIGITAL (BUFFER) C3114 1 R3222 100 IC3101(3/7)
AUDIO OUT AC13 DIGITAL
(COAXIAL) C3708 D3702 R3726 C3707 SIGNAL
100P OPEN 110 33P R3171 R3168 R3167 PROCESS
75 75 75 TO DIGITAL
MAIN 8
AUDIO(L)-IN R3155 100 IC3101(7/7)
C3710 R3708 D3703 Y11 VGA-HSYNC
56P 10K OPEN R3154 100
AA12 VGA-VSYNC
TO DIGITAL
MAIN 5
AUDIO(R)-IN C3711 R3709 D3707 R3147 36 C3103 1 IC3101(4/7)
56P 10K OPEN W11
R3148 36 C3104 1
AA11
JK3713 R3149 36 C3105 1
AB12
PC-RGB-IN R3145 36 C3102 1
AA10 TO DIGITAL
MAIN 1
IC3101(1/7)
1 6 11 E4 NU
R3195 10K
D2 NU
2 7 12 R3196 10K
F6 NU
R3197 10K
3 3
4
8
9
13
14
R3199 OPEN
G5
E3
SPDIF
NU
NU
F4
C3207 1 R3297 100K
5 10 15 AE14
C3208 1 R3298 100K
D3711 1SS400
AC14
OPEN
OPEN
OPEN
OPEN
OPEN
R3839 47K
R3838 47K
R3831 10K
R3830 10K
AB14 NU
AC15 NU TO DIGITAL
MAIN 8
D3717
D3716
D3715
D3714
D3713
AC16 NU IC3101(7/7)
AD16 NU AUDIO
I/F
CONTINUE AB16 NU
DIGITAL 7 D3712
1SS400 AE17 NU
P-ON+5V TO DIGITAL
AD17 MAIN 5
P-ON+3.3V AC17 IC3101(4/7)
AMP+13V AB17
AC18
CONTINUE
DIGITAL 8 E2 AUDIO-MUTE
VGA-SCL F5 ARC-OUT
VGA-SDA CONTINUE
DIGITAL 8
CONTINUE ARC-OUT
DIGITAL 2
P-ON-H2
R3733 R3751
2 R3809
10K
R3810
OPEN
3.3
C3713
R3728 220/6.3V
4.7K 47K
JK3801
HEADPHONE
R3729 R3737 R3746 C3712
R3738 220/6.3V R3743 JACK
3.3 10K 10K 10K 10K
C3825 C3824
R3811 R3826 1 0.047 R3731 R3740 R3752
1K OPEN OPEN OPEN OPEN
IC3803 Q3708
R3820 R3813 TPA3110D2PWPR OPEN
560 10 (AUDIO AMP) R3739 R3744
Q3821 OPEN OPEN Q3701
2SA1576UBTLQ OPEN
(SWITCHING) 1 PVCCL 28 R3732
C3830 R3812 CONTROL OPEN
OPEN 100K LOGIC Q3710
2 PVCCL 27 OPEN
R3713 C3718
R3822 C3805 1 C3801 0.22 OPEN OPEN
10K 3 26
CONTINUE POWER PWM DRIVE L3801
DIGITAL 7 C3832 C3818 1 LIMIT LOGIC 10uH
R3823 22K 4 25
HP-MUTE 1.8K R3805 OPEN R3801 C3811 C3820 C3834 C3838 D3801
AUDIO-MUTE R3824 5 GND 24 OPEN 1000P 1 OPEN OPEN OPEN
10K Q3822 GAIN C3807
LCD-P-ON 2SC4081UBTLQ R3806 0 CONTROL OPEN L3802
(SWITCHING) 6 23
R3825 DRIVE 10uH
CONTINUE 47K C3802 0.22
DIGITAL 8 R3828 7 AVCC 22
OPEN R3802 C3812 C3821 C3835 C3839 D3802
SP-MUTE C3815 R3807 OPEN C3803 0.22 OPEN 1000P 1 OPEN OPEN OPEN
1 8 GND 21 C3808
C3816 1 DRIVE OPEN L3803
9 GVDD 20 10uH SP3801
R3808 CN3801 SPEAKER
C3817 1 10K
1 R3814
OPEN
R3817
OPEN
R3821
560
C3819 1
C3806 1
10
11
POWER
LIMIT
PWM
LOGIC DRIVE
GND 19
18
C3827
0.047
C3804 0.22
C3828
1
R3803
OPEN
C3809
OPEN L3804
10uH
C3813
1000P
C3822
1
C3836
OPEN
C3840 D3803
OPEN OPEN 1
2
3
SP(L)+
SP(L)-
SP(R)-
L-CH
12 17 4 SP(R)+ SP3802
R3815 R3818 C3833 R3804 C3814 C3823 C3837 C3841 D3804 SPEAKER
OPEN OPEN 22K 13 NU PVCCR 16 OPEN 1000P 1 OPEN OPEN OPEN R-CH
C3810
R3816 R3819 14 PBTL PVCCR 15 OPEN
OPEN OPEN C3831 C3826 C3829
100/16V 220/16V OPEN
AE AF AG AH AI AJ
10-11 PL13.11ASCD6
CONTINUE
DIGITAL 2 C3182
P-ON+21V C3630 2700P
OPEN
P-ON+3.3V R3630
0 *1
IC3604 R3626 IC3101(6/7)
CONTINUE RT8293ALZSP 0 MN2WS0270EA
DIGITAL 6 R3609
4 HP-MUTE
AUDIO-MUTE
LCD-P-ON R3610
OPEN
R3611
OPEN
10K
C3639
0.01
(+1.14V REG.)
1 BS
2 VIN
SS 8
EN 7
C3601
0.015
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
AFB R4
R3223
0
Q3601 C3183
OPEN C3645 C3655 C3656 C3654 OPEN
R3612 4.7 0.1 0.1 OPEN 3 SW COMP 6
CONTINUE OPEN C3638 R3181 C3134
DIGITAL 8 4 GND FB 5 0.015 0 1
STB-RESET R3676 AVDDVAD11 U12
OPEN R3613 R3625
LCD-P-ON OPEN 2.2K LVVDD11 K11
R3624 VDD11 *A C3132 C3136 C3142 C3138
BACKLIGHT-SW L3601 OPEN L3102 1 10 10 1
10uH 0
PROTECT3 AVDDH11 AC21
PROTECT1 R3689 C3646 C3641 C3643 C3642 C3644 C3139 C3143 C3144 C3130 C3131
OPEN OPEN 10 10 OPEN OPEN AVDDH11 AD21 1 1 1 0.1 0.1
P-ON-H2 C3133
HP-MUTE C3969 OPEN CONTINUE
OPEN DIGITAL 5
AVDD11-CEN T9 CTRL11
R3607 IC3601 AVDD11-RX AB4 C3147 C3148 C3149
56K C3605 0.1 0.1 0.1
R3601 PST8429UR 1000P DVDD11 T10
CONTINUE OPEN (RESET) C3616 C3615 C3609
DIGITAL 1 R3602 4.7 0.1 OPEN VDD33-1 N12
BACKLIGHT-ADJ 220 1 GND OUT 4 IC3603 VDD33-2 N13 C3178 C3179 C3156 C3157 C3158
MP1472GJC452Z 1 1 10 0.1 0.1
D3601 2 VDD CD 3 (+3.3V REG.) DPAVDD33 M12
TO POWER SUPPLY OPEN D3603 C3606 C3607
3 CBA CN501
LED-CONT(NU)
PROTECT1
PROTECT3
CN3601
1
2
3
R3620 100
R3603 100
OPEN
R3608
270
C3602
1 0.01
C3604
0.033
R3606 C3611
11K 3300P
1 SS
2 EN
BST 8
VIN 7 C3612
0.01
AVDDH33
VDDEM18-33
LVVDD33-1
LVVDD33-2
AB21
M13
L11
M11 C3155
L3101
BEAD
2 P-ON+21V
P-ON+21V
P-ON+21V
P-ON+21V
20
21
22
23
C3676
OPEN
D3605
MM5Z15B
Q3602
R3622
10K
C3665 R3627
OPEN 100K
R3635 C3666
5.1K 4700P
2 EN
3 COMB
4 FB
VIN 7
SW 6
GND 5
0.01 VDDSD18-33 J21
AVDD33-CEN P10
C3169
0.1 L3106
BEAD
R3615 2SA1576UBTLQ D3609 C3613
10K (SW+12V) OPEN OPEN R3633 R3679 AVDD33-TX P9 C3170 C3171 C3177
10K 6.2K 0.1 0.1 10 R3184
CONTINUE 0
DIGITAL 6 D3608 R3095 R3634 L3603 VDDTCON25-33 M9
R3618 1SS400 10K 100 10uH
P-ON+5V 4.7K C3168
0.1 CONTINUE
P-ON+3.3V R3619 C3668 C3672 C3670 C3671 C3669 R3685 DIGITAL 3
Q3603 10K 470/4V 10 10 10 OPEN OPEN
AMP+13V 2SC4081UBTLQ STMADAVDD33 M10 AL+3.3V
(SWITCHING) R3621 C3610 C3968 C3174 C3173 C3172
OPEN 1 OPEN STMRONA T4 0.1 10 1 VCC+1.5V
CONTINUE VDDSTM33 L10
DIGITAL 4
P-ON+3.3V VDDIO15 *B
P-ON+5V C3625 C3632 C3631 C3153 C3152 C3141 C3145 C3146 C3150
4.7 0.1 OPEN 10 1 1 1 1 1
AL+3.3V IC3607
MP1472GJC452Z
(+5V REG.) C3137 C3140 C3151 C3184 C3185
CONTINUE R3631 C3617 1 1 1 1 1 L3108
DIGITAL 5 0 0.1 BEAD
P-ON+5V 1 SS BST 8 VDDIOCK15 D5
P-ON+3.3V 2 EN VIN 7 C3620 VDDSTM11 N10 C3154
R3614 C3619 0.01 0.1
R3623 C3618 4.3K 4700P FPEN N9 C3175
22K OPEN 3 COMB SW 6 1
1 CONTINUE
DIGITAL 8
P-ON+5V
P-ON+3.3V
D3606
1SS400 R3617
10K
R3678
12K
4 FB GND 5
TESTSEL
NU
GND
R12
*C
*D
*A:J11~J17,K12~K17,L14~L17,M15~M17
*B:E9,F8,F9,G13~G15,G19
R3616 *C:H5,P23,R13,R23,R24,T13,T22,T23,U22,U24,U25,
AL+3.3V 33K L3605 R3022 0 V5,AD1,AD2,AE2
22uH
R3023 0 *D:A1,A9,A25,C10,D13,E5,E6,E12,E13,F7,F13,F15,
D3615 C3628 C3621 C3623 R3696 HEAT SINK G17,G18,H7,H8,J9,J10,K9,K10,L9,L12,L13,M14,
CRY68 10 10 OPEN OPEN R3024 0 N6,N7,N14~N17,P11~P17,R10,R11,R14,R17,T11,
T12,T14,T17,U13,U14,U16,U17,W12,W13,Y14,
AA14,AC4,AE1,AE25
DIGITAL MAIN CBA UNIT C3966
OPEN
AK AL AM AN AO AP
10-12 PL13.11ASCD7
4 R3188
OPEN R3209
OPEN
R3200
OPEN R3109 10K
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
JK3717
HDMI-
CONNECTOR-1
R3206 AA4 NU AD24 1 DATA2(+)
OPEN Q3108 Y1 NU
OPEN AE24 2 TMDS DATA2 SHIELD
R3215 AB1 NU AD23 3 DATA2(-)
R3207 OPEN AB3 NU
OPEN AE23 4 DATA1(+)
(NO CONNECTION) CN3103 AB2 NU
AL+3.3V 1 AC23 5 TMDS DATA1 SHIELD
Y4 NU AE22 6 DATA1(-)
P-ON-H2 2 V6 NU
R3131 AD22 7 DATA0(+)
1K R3212 AA3 NU
100K AC22 8 TMDS DATA0 SHIELD
V4 NU Y23 9 DATA0(-)
CONTINUE AA24 10 CLOCK(+)
DIGITAL 2 R3120 AA23 11 TMDS CLOCK SHIELD
PROTECT3 OPEN
W4 LED2 HDMI AB25 12 CLOCK(-)
C3100 Q3103 R3143 I/F
CONTINUE OPEN OPEN OPEN AB24 13 HDMI-CEC
DIGITAL 7 AC25 14 ARC
P-ON+5V AC24 15 HDMI-CLOCK
P-ON+3.3V AD25 16 HDMI-DATA
AL+3.3V U23 R3721 R3718 R3706 17 GND
R3096 10K 47K 47K
22K V24 18 +5V
TO FUNCTION CBA C3702 R3722 R3703 R3705
UNIT CN4052 CN3105 Y5 SW-EN V23 0.1 47K 10K 1K 19 HOT PLUG DETECT
SDA(NU) 1 U3 REMOTE V22
3 SCL(NU)
GND
KEY-IN1
2
3
4
R3117
10
R3107
100
C3107
R3146
100K
V3 LED1 W23
W22
Y25
R3701
10K Q3707
2SC4081UBTLQ
(SWITCHING)
R3719
OPEN
JK3716
1
HDMI-
CONNECTOR-3
DATA2(+)
REMOTE 5 OPEN R3102 Y24
1K 2 TMDS DATA2 SHIELD
LED1 6 R3323
33 Q3102 3 DATA2(-)
LIGHT 7 2SC4081UBTLQ
P-ON+5V 8 C3110 C3112 R3119 C3108 (BUFFER) 4 DATA1(+)
OPEN OPEN OPEN 1
C3111 AUDIO VIDEO 5 TMDS DATA1 SHIELD
AL+3.3V 9 0.1 DECODER DECODER
C3101 6 DATA1(-)
0.1 Q3101 R3106 R3159 7 DATA0(+)
C3122 OPEN 2SC4081UBTLQ 10K 0
(LED DRIVE) T3 LIGHT-SENS 8 TMDS DATA0 SHIELD
CONTINUE C3123 OPEN R3103 R3104 C3106 R3182 TO DIGITAL TO DIGITAL
DIGITAL 4 10K 27K 33/10V OPEN MAIN 6 MAIN 6 9 DATA0(-)
STB-RESET R3105 IC3101(5/7) IC3101(5/7) 10 CLOCK(+)
R3110 R3114 100 R3179 100
STMTIME1 33 33 U1 KEY-IN1 HDMI-CEC Y3 11 TMDS CLOCK SHIELD
D3101 STMCECPUL T6 12 CLOCK(-)
OPEN R3150 R3161 100 R3134 39
10K T2 PROTECT3 HDMI0-SCL T7 13 HDMI-CEC
CONTINUE R3160 100 R3137 39
DIGITAL 7 U5 PROTECT1 HDMI0-SDA W6 14 NU
R3139 39
STB-RESET AD5 STB-RESET HDMI1-SCL R9 15 HDMI-CLOCK
R3162 22 R3140 39
LCD-P-ON W2 LCD-P-ON HDMI1-SDA AE3 16 HDMI-DATA
R3133 100 R3141 39 R3781 R3780
BACKLIGHT-SW W3 BACKLIGHT-SW HDMI2-SCL V7 R3784 47K 47K 17 GND
R3142 39 10K
PROTECT3 Y2 P-ON-H2 HDMI2-SDA AA5 18 +5V
PROTECT1 C3759 R3785 R3710 R3779 19 HOT PLUG DETECT
R3138 OPEN 0.1 47K 10K 1K
P-ON-H2 AB6 P-ON-H2
HP-MUTE W7 HP-MUTE HDMI0-HPD R7 R3707 R3783
10K Q3702
2 CONTINUE
DIGITAL 6
SP-MUTE
W5 STMTIME1
AA2 SP-MUTE
HDMI1-HPD U2
HDMI2-HPD U6
HDMIO-5V AB5
2SC4081UBTLQ
(SWITCHING)
OPEN
JK3715
1
HDMI-
CONNECTOR-2
DATA2(+)
2 TMDS DATA2 SHIELD
HDMI1-5V AA6 3 DATA2(-)
HDMI2-5V AC3 4 DATA1(+)
R3863
C3127 27K 5 TMDS DATA1 SHIELD
0.1 R3152 R3153
IC3103 4.7K 4.7K D3722 6 DATA1(-)
1SS400
M24C16-WMN6TP R3865 7 DATA0(+)
(MEMORY) R3156 39 22
AC2 STM-SCL 8 TMDS DATA0 SHIELD
1 A0 VCC 8 R3157 39 R3165 39 9 DATA0(-)
AC1 STM-SDA VGA-SCL Y7
R3158 22 R3178 39 10 CLOCK(+)
2 A1 WP 7 U4 STM-EEPROM-WP VGA-SDA AD3
NU U7 11 TMDS CLOCK SHIELD
3 A2 SCL 6 R3151
10K HDMI-UART-CTRL Y6 12 CLOCK(-)
4 VSS SDA 5 13 HDMI-CEC
14 NU
R3730 C3719 15 HDMI-CLOCK
0 220P 16 HDMI-DATA
R3777 R3773 R3774 17 GND
Q3706 R3714 10K 47K 47K
OPEN 10K Q3704 18 HDMI+5V
2SC4081UBTLQ C3750 R3778 R3712 R3775 19 HOT-PLUG-DETECT
R3720 (SWITCHING) 0.1 47K 10K 1K
R3771 33K
1 R3772
OPEN
OPEN
C3717
R3711
10K Q3703
2SC4081UBTLQ
(SWITCHING)
R3776
OPEN
220P
R3717
0
CONTINUE R3715
DIGITAL 5 Q3705 10K
2SC4081UBTLQ CONTINUE
UART1TX (SWITCHING) R3716 DIGITAL 6
UART1RX 33K VGA-SCL
VGA-SDA
AQ AR AS AT AU AV
10-13 PL13.11ASCD8
CONTINUE
DIGITAL 4
P-ON+21V
R3630 P-ON+3.3V
0 R3045
12K R3047 R3046 C3057 C3058 PROTECT3
R3044 3.9K 12K 47/25V 0.1
11K R3042 D3008
OPEN OPEN CONTINUE
DIGITAL 3
4 R3632
OPEN
D3624
OPEN
Q3007
2SC4081UBTLQ
(SWITCHING) C3000
OPEN
R3048
1K
CELL-PWR-CTRL
VCOM-PWM
R3622
OPEN
TO LCD PANEL
R3621 C3628 CN3013 ASSEMBLY
OPEN OPEN 1 NU
C3624 C3623 C3622 C3621 C3170 C3171
D3623 OPEN OPEN OPEN OPEN OPEN OPEN 2 NU
OPEN 3 NU
IC3621
C3627 OPEN 4 NU
OPEN R3172 5 NU
1 SS BST 8 OPEN
C3625 R3627 6 GND
OPEN OPEN
2 EN IN 7 7 GND
C3629 R3623 C3626
OPEN OPEN OPEN 8 GND
3 COMP SW 6 R3440 OPEN R3430 OPEN
C3630 9 NU
4 FB GND 5 OPEN L3621 R3439 OPEN R3431 OPEN
R3625 R3624 OPEN 10 NU
OPEN OPEN R3626 R3628 R3435 OPEN
OPEN OPEN 11 NU
R3436 OPEN
12 NU
13 RXO3(+)
R3631 R3629 D3622 D3621 C3636 C3635 C3634 C3633 C3632 C3631
3 *1
IC3005(1/6)
R8A05011BG-U0
OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN 14
15
16
17
RX03(-)
GND
RXOCLK(+)
RXOCLK(-)
DIGITAL SIGNAL PROCESS 18 GND
/MAIN MICRO CONTROLLER
19 RXO2(+)
R3088 20 RXO2(-)
7.5K
NU K15 21 RXO1(+)
T13 22 RXO1(-)
C3647 23 RXO0(+)
R13 OPEN
24 RXO0(-)
R3442 OPEN R3432 0
T14 25 NU
C3646 R3441 OPEN R3433 0
R14 OPEN 26 NU
R3437 OPEN
27 NU
T15 R3438 OPEN
C3645 28 NU
T16 OPEN 29 RXE3(+)
R15 30 RXE3(-)
LVDS C3644
TX OPEN 31 GND
R16 32 RXECLK(+)
P15 33 RXECLK(-)
C3643
2 P16
N15
N16
OPEN
C3642
OPEN
34
35
36
37
GND
RXE2(+)
RXE2(-)
RXE1(+)
P13 38 RXE1(-)
C3641 39 RXE0(+)
P14 OPEN
40 RXE0(-)
NU N13 41 GND
C3676 R3165 0
NU N14 OPEN 42 NU
R3166 0
TO DIGITAL 43 P-ON+3.3V
NU M13 R3129 R3167 0
MAIN 2 C3675 R3168 44 P-ON+3.3V
IC3005(2/6) OPEN 0 OPEN
STV M14 45 VCOMA
POL M15 46 DCDC-EN
C3674 R3169 R3130 C3162 R3170 0
OPEN R3524 0 OPEN OPEN 47 NU
NU M16 OPEN R3173 0
48 LCD+21V
R3174 0
TP L13 R3171 49 LCD+21V
C3673 0
OE2 L14 OPEN 50 LCD+21V
C3167 C3166 51 NU
OE L15 1000P 4.7 R3434
C3672 0
CPV L16 OPEN
CN3602 (NO CONNECTION)
1 1 GND
OPEN
OPEN
OPEN
OPEN
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
2 NU
3 NU
C3662
C3663
C3664
C3665
C3666
C3667
C3668
C3669
C3670
C3671
C3648
C3649
C3650
C3651
C3652
C3653
C3654
C3655
C3656
C3657
C3658
C3659
C3660
C3661
4 NU
C3161
OPEN
A B C D E F
10-14 PL13.11BSCD1
74LVC1G126GW
IF-AGC
(BUFFER GATE)
+3.3V
GND
SDA
SCL
1 VCC 5
C3214 Q3301
1 2 3 4 5 6 7 2 0.1 2SK3018
(BUFFER) Q3302
4 C3903 0.1
C3902 0.1
3 GND 4 2SK3018
(BUFFER)
CONTINUE
DIGITAL 6
VGA-SDA
VGA-SCL
IC3014
74LVC1G126GW
(BUFFER GATE)
1 VCC 5 CONTINUE
L3913 DIGITAL 4
2.2uH
2 P-ON+3.3V
C3905 C3901 D3901 C3934 C3909 C3175 C3176 R3204 P-ON+5V
10 220/6.3V MM5Z5V6B OPEN OPEN 33P 33P 2.7K 3 GND 4
3 MAIN 5
IC3005(5/6) DEMODULATOR
/MPEG
DECODER
A12
C3173
33P
C3172
R3251
10
R3250
R3333
10
R3343
OPEN 13 8 3
2 TO DIGITAL
MAIN 3
NU
NU
B9
D9
C3708 R3701
JK3702
COMPONENT
-Y/VIDEO-IN
DIGITAL IC3005(3/6) 0.1 OPEN
R3711
SIGNAL 10K
PROCESS COMPONENT
TO DIGITAL R3702 -Pb-IN
MAIN 3 OPEN
IC3005(3/6) R3710
100
COMPONENT
C3707 R3712 Q3701 R3703 -Pr-IN
1 10K 2SC4081UBTLQ OPEN
(BUFFER)
R3709 C3706 JK3701
C3335 220 1
TO DIGITAL TO DIGITAL 2.2 C3285 0.1 DIGITAL
NU B10 R3708 C3709 AUDIO-OUT
MAIN 6 MAIN 1 C3286 0.1 110 100P (COAXIAL)
IC3005(6/6) IC3005(1/6) NU A11
C3336 1
NU D10 AUDIO(L)-IN
R3704
100K
AUDIO(R)-IN
R3705
100K CONTINUE
DIGITAL 5
1 SCL
SDA
AUDIO(L)-IN
AUDIO(R)-IN
CONTINUE
DIGITAL 5
SPDIF
G H I J K L
10-15 PL13.11BSCD2
C3009 R3082 *1
OPEN 100 IC3005(3/6)
R8A05011BG-U0
DIGITAL SIGNAL PROCESS C3184
R3064 C3050 /MAIN MICRO CONTROLLER 18P
100 0.1
M5 SD-VREF0
R3065 C3051 N3 GND X3001
100 0.1 XIN25 H15 R3223 25MHz C3183
1K 20P CN3012 (NO CONNECTION)
4 IC3002
SD-DQ15
SD-DQ14
R8
N8
SD-DQ15
SD-DQ14
XOUT25 H16
ASEBRKAK-N F15
R3527 OPEN
1
2
3
AL+3.3V
GND
ASEBRKAK-N
K4T51163QJ-BCE7 SD-DQ13 ASEMD0 F16 4 ASEMD0
(DDR2 SDRAM) P7 SD-DQ13 TRST-N E16 5 TRST-N
SD-DQ12 R6 SD-DQ12 R3525 OPEN
C3029 0.1 TCK E15 6 TCK
*A VDD SD-DQ11 P6 SD-DQ11 R3526 OPEN
C3030 0.1 VREF J2 TDI D16 7 TDI
SD-DQ10 N7 SD-DQ10
C3031 0.1 C3010 R3083 TDO D15 8 TDO
0.1 100 SD-DQ9 T5 SD-DQ9
C3032 0.1 TMS E14 9 TMS
CKE K2 SD-DQ8 P8 SD-DQ8 TO DIGITAL
C3033 0.1 MAIN 2 R3522 10 CPU-RESET-N
E2 NU CK J8 SD-DQ7 P4 SD-DQ7 IC3005(2/6) 10K
C3034 0.1
A2 NU CK K8 SD-DQ6 T3 SD-DQ6 R3395 CN3010 (NO CONNECTION)
C3035 0.1 R3049 4.7K
R8 NU CS L8 150 SD-DQ5 R4 SD-DQ5 1 P-ON+5V
C3037 0.1 R3468 100
R7 NU RAS K7 SD-DQ4 T2 SD-DQ4 TXD0 G15 2 UART0-TX
C3038 0.1 R3469 100
R3 NU CAS L7 SD-DQ3 P3 SD-DQ3 RXD0 G16 3 UART0-RX
C3039 0.1 C3253
WE K3 SD-DQ2 T4 SD-DQ2 OPEN 4 GND
C3040 0.1 C3254 C3255 R3396
1-O3 B7 UDQS BA2/NU L1 SD-DQ1 R3 SD-DQ1 OPEN OPEN 4.7K
C3041 0.1
2-O3 A8 UDQS/NU BA1 L3 SD-DQ0 N4 SD-DQ0
C3140 0.1 CONTINUE
3-O3 B3 UDM BA0 L2 3-M3 T6 SD-UDM DIGITAL 2
SD-DQ15 B9 DQ15 A12 R2 6-M3 R5 SD-LDM COMP-DET
R3516 100
SD-DQ12 2-M3 BACKLIGHT-ADJ F3
3 SD-DQ10
SD-DQ9
SD-DQ14
B1
D9
D1
D3
DQ12
DQ10
DQ9
DQ14
A11
A10/AP
A9
A8
P7
M2
P3
P8
1-M3
5-M3
4-M3
T7
R7
N5
P5
SD-UDQSN
SD-UDQS
SD-LDQSN
SD-LDQS
VCOM-PWM F2
GND J14
R3517 100 CONTINUE
DIGITAL 5
CPU-RESET-N
SD-DQ13 D7 DQ13 A7 P2
SD-DQ11 C2 DQ11 A6 N7
SD-DQ8 R3030 33x4 H1 SD-A4 R3511 22 CONTINUE
C8 DQ8 A5 N3 CELL-PWR-CTRL D1 DIGITAL 4
4-O3 F7 LDQS A4 N8 H3 SD-CAS GPY10 E13 GPY10
5-O3 E8 LDQS/NU A3 N2 J2 SD-A11 CPU-RESET-N
6-O3 J1 SD-A0 R3211 100
F3 LDM A2 M7 R3031 33x4 P-ON-H2 B16 P-ON-H2
SD-DQ3 J4 SD-A10 R3233 22
F9 DQ3 A1 M3 HP-MUTE G13 BACKLIGHT-ADJ
SD-DQ2 L1 SD-A1 R3188 22
F1 DQ2 A0 M8 BACKLIGHT-SW E2 BACKLIGHT-SW
SD-DQ7 H9 DQ7 ODT K9 K4 SD-BA1
R3503
SD-DQ6 L2 SD-A9 10K CONTINUE
H1 DQ6 R3032 33x4 DIGITAL 1
SD-DQ4 H3 DQ4 L4 SD-WE CELL-PWR-CTRL
SD-DQ1 VSS *B N2 SD-BA0
H7 DQ1 TO DIGITAL VCOM-PWM
SD-DQ5 G2 DQ5 P1 SD-BA2 MAIN 2 R3510 22K
SD-DQ0 M3 SD-A3 IC3005(2/6)
G8 DQ0 CONTINUE
R3033 33x4 M1 SD-A5 DIGITAL 5
R3515 4.7K
M2 SD-A12 LED1 D14 LED1
*A:A1,A9,C1,C3,C7,C9,E1,E9, R3213 22
G1,G3,G7,G9,J1,J9,M9,R1 L3 SD-CKE REMOTE C14 REMOTE
R3217 22
2 *B:A3,A7,B2,B8,D2,D8,E3,E7,
F2,F8,H2,H8,J3,J7,N1,P9 R3034 33x4
N1
J3
K3
SD-A7
SD-RAS
SD-A6
AUDIO-MUTE C1
R3234
OPEN
K1 SD-A2
CONTINUE
K2 SD-ODT DIGITAL 4
IC3006 H2 SD-A8 R3201 P-ON+1.8V
S25FL032P0XMFI010 R3102 R3016 33 R3215 22 33K
10K R2 SD-CLK COMP-DET N12 P-ON+3.3V
(MEMORY) R3084 10
R1 SD-CLKN AL+3.3V
1 CS VCC 8 R3087 10
R3107 H4 NU P-ON+5V
10K C3073 R3070 150
2 SO NU 7 0.1
R3089 47
P12 CS
3 WP SCK 6 R3092 47 CONTINUE
R11 SOUT DIGITAL 5
R3093 47
4 GND SI 5 P11 SIN C3072 10 HP-MUTE
R3094 47 NU H14
R3479 T11 SCK AUDIO-MUTE
10K R3095 22
T9 VBUS-EN BACKLIGHT-SW
R9 VBUS-ST
R10 USBDP
(USB JACK) CN3009 C3246 C3348 T10 USBDN
1 220/6.3V R3099 5.6K
BUS-POWER 1 P10 NU
USBDN 2 IC3019
1 USBDP
GND
3
4 L3025
EXC24CG900U
AP2151WG-7
(HIGH SIDE SW)
1 OUT IN 5
C3327
2 GND 1
3 /FLAG RN 4
R3480
10K
DIGITAL MAIN CBA UNIT
M N O P Q R
10-16 PL13.11BSCD3
CONTINUE
*1 DIGITAL 3
IC3005(4/6) R3221 P-ON+1.8V
R8A05011BG-U0 100
DIGITAL SIGNAL PROCESS P-ON+3.3V
/MAIN MICRO CONTROLLER R3222 AL+3.3V
10K L3027
BEAD P-ON+5V
VCC33STB F12
C3160 R3106 R3100 R3036
4 VCC33STB G12
VDD12STB E12
0.1
D
G
S
Q3006
2SA1576UBTLQ
47K
R3105
10K
22K
Q3101
2SC4081UBTLQ
(SWITCHING)
D3105
OPEN D3103
HSC119
R3424
100 IC3004
100
CONTINUE
DIGITAL 6
P-ON+3.3V
(SWITCHING) BD00IA5WEFJ-E2 AL+3.3V
L3030
0 Q3013 Q3005 C3265 R3138 (+1.2V REG.) P-ON+3.3V(1)
C3181 SSM3K309T 2SC4081UBTLQ 10 OPEN
0.1 (SW+12V) R3423 D3115 1 VOUT VCC 8 P-ON+5V
(SWITCHING) R3097 47K HSC119
1.5K C3024 CONTINUE
D3101 2 FB NU 7 10 DIGITAL 2
VDD12 *C HSC119 P-ON+3.3V
R3061 R3060 C3019
C3123 C3124 C3125 C3126 C3132 C3133 D3102 10K 2.7K 0.022 3 GND NU 6 P-ON+5V
1 1 1 1 10 10 HSC119 R3059 R3062
2.7K 1.8K
4 NU EN 5
C3127 C3128 C3129 C3130 C3134 R3043 C3086
1 1 1 1 1 180 10 CONTINUE
R3228 R3086 DIGITAL 1
OPEN Q3011 4.7K
OPEN R3008 P-ON+21V
AVDD12 M10 C3237 R3227 D3104 C3131 1
OPEN OPEN HSC119 Q3003 1 P-ON+3.3V
C3135 R3077 2SC4081UBTLQ
0.1 L3021 10K (SWITCHING) PROTECT3
BEAD IC3601
AVDD12 E8 AP2121AK-3.3TRE1 L3003
AVDD12 F8 C3118 C3136 C3114 C3115 R3605 (+3.3V REG.) R3079 Q3004 OPEN
10 1 10 10 0 10K 2SC4081UBTLQ IC3007
AVDD12 F9 1 VIN VOUT 5 (SWITCHING) BD00IC0WEFJ CONTINUE
C3609 C3610 (+1.8V REG.) DIGITAL 5
1 2 GND R3606 1 RESET
3 VDDCLK G11
C3139
0.1
R3608
4.7K
C3611 R3609
OPEN OPEN
3 CE NU 4
OPEN
R3607
OPEN
D3106
HSC119 R3111
10K
R3110
10K
C3075
0.022
1 VOUT
2 FB
VCC 8
NU 7
C3069
10
C3068
OPEN
PROTECT1
PROTECT3
3 GND NU 6
R3109 R3103 CONTINUE
3.3K 1.8K DIGITAL 5
VCCQ18 H5 4 NU EN 5
P-ON+3.3V
VCCQ18 J5 C3326 C3325 C3324 C3343 C3264 C3079 C3087
10 OPEN OPEN 10 OPEN 220/6.3V 10 CHECK+1.8V
VCCQ18 M4 AL+3.3V
VCCQ18 T1 P-ON+5V
C3322 C3321 C3320 C3319 C3318
VCCQ18 M6 10 OPEN 10 10 10 P-ON+3.3V(1)
VCCQ18 N6 AMP+13V
VCCQ18 M7 C3141 C3142 C3143 C3144 C3145 C3080 C3103 C3007 C3102 C3003 C3002
1 1 1 1 1 4.7 OPEN 0.1 IC3008 4.7 0.1 OPEN IC3001
VCCQ18 M8 MP1472GJC452Z MP1472GJC452Z C3604 C3603 D3602
L3019 (+1.2V REG.) (+3.3V REG.) 10 1 MM5Z4V3B
OPEN C3083 C3013 R3071
AVDD33 E10 0.015 0.047 1 CONTINUE
C3148 C3149 C3150 D3113 1 SS BST 8 1 SS BST 8 DIGITAL 3
AVDD33 C2 1 10 1 MM5Z5V6B R3133 C3091 R3091 C3092 GPY10
10K OPEN C3085 0 OPEN C3014
AVDD33 C3 2 EN IN 7 R3141 0.1 2 EN IN 7 R3057 0.1 CPU-RESET-N
C3090 C3088 R3137 OPEN C3119 C3017 R3001 OPEN
AVDD33 E11 1 4700P 2.7K OPEN 2200P 8.2K P-ON-H2
3 COMP SW 6 3 COMP SW 6
BACKLIGHT-ADJ
L3026 4 FB GND 5 4 FB GND 5
BEAD L3009 L3002 BACKLIGHT-SW
AVDD33 D6 10uH 33uH
2 L3006
BEAD
C3151
1
C3152
1
C3154
1
D3114
MM5Z5V6B C3099 R3142 R3149 C3094 C3096 C3065 C3097 R3602 D3005 R3004 C3020 C3021 C3059 R3014 R3601
OPEN
OPEN OPEN 3.9K 330/4V 10 10 OPEN OPEN PTZTE255.1B 33K 330/4V 10 10 270 OPEN
220
100
100
100
AVDD33 E6 R3145 C3606 R3003 C3605
C3155 C3156 1.2K OPEN 6.2K OPEN
1 1
R3013
R3011
R3009
R3072
R3068
1
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
6 AMP+13V
R3006
10K 5 GND
4 P-ON+21V
C3996 3 P-ON+21V
OPEN
2 P-ON+21V
DIGITAL MAIN CBA UNIT 1 P-ON+21V
S T U V W X
10-17 PL13.11BSCD4
CONTINUE
DIGITAL 4
P-ON+3.3V
CHECK+1.8V
AL+3.3V
P-ON+5V
P-ON+3.3V(1) *1
IC3005(5/6)
AMP+13V R8A05011BG-U0
CONTINUE DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
4 DIGITAL 3
LED1
REMOTE
R3552 R3558
Q3502
2SA1576UBTLQ
(LED DRIVE)
R3559
R3312 10K
D13 CHECK+1.8V NU G1
NU E1
TO FUNCTION CBA 100 OPEN 10K
UNIT CN4052 CN3101 NU G2
CONTINUE
SDA(NU) 1 R3560 R3210 R3402 DIGITAL 6
100K 100 0
SCL(NU) 2 HPD-SINK K14 HPD-SINK
GND 3 PWR J16 PWR
C3555 R3320 R3216 R3401
KEY-IN1 4 OPEN OPEN 100 0
REMOTE 5 C3559 R3551 R3555
OPEN 100 OPEN Q3010 R3220
LED1 6 2SC4081UBTLQ 33K
R3318 22K
R3317 10K
R3319 10K
(BUFFER) R3219
LIGHT 7 22
C3553 C3556 C3558 R3183 HP-DET K16
P-ON+5V 8 OPEN OPEN 10 100
D3201
AL+3.3V 9 MM5Z5V6B
C3554 C3560 Q3501 R3185 CONTINUE
1 OPEN 2SC4081UBTLQ 10K R3191 DIGITAL 3
(LED DRIVE) 100
C3329 0.01 RESET J15 CPU-RESET-N
C3551 33P R3184 R3186 D3111
R3553 D3501 10K 39K A15 KEY-IN1 MM5Z5V6B
C3552 33P 100 MM5Z5V6B R3314 22
CONTINUE
DIGITAL 4 B13 PROTECT3
R3315 22
RESET A13 LIGHT-SENS
R3316 22 IC3009
PROTECT1 C13 PROTECT1 R3178 PST8429UR R3182
3 PROTECT3
C3231
C3328
OPEN
0.22
C12 LPF
TO DIGITAL TO DIGITAL
MAIN 2 MAIN 6
220 (RESET)
1 GND OUT 4
56K
1000P
1000P
C3220 10
SDA NU C6
R3335 18K C3217 2.2 C3216 10
AUDIO(L)-IN A8 NU C5
R3336 18K C3218 2.2
AUDIO(R)-IN B8 AUDIO NU B6
C3223 1 I/F CONTINUE
R3995 R3862 B7 NU A6 R3209 DIGITAL 2
CONTINUE 10K 10K C3224 1 100
DIGITAL 3 A7 N10 SPDIF
HP-MUTE
AUDIO-MUTE R3865
10K
BACKLIGHT-SW
R3561 C3860 R3866 C3862
10 0.1 100K OPEN
R3867 R3868
0 OPEN
R3809 R3810 R3864
OPEN OPEN 1K R3851 C3851
15K 1 C3853
220/6.3V
R3861 R3853 JK3703
10K Q3861 OPEN C3856 R3856 HEADPHONE
C3825 C3824 2SC4081UBTLQ 1000P 10K JACK
2 R3814
OPEN
Q3803
R3870
220
R3813
OPEN
R3822
10
IC3801
TPA3110D2PWPR
(AUDIO AMP)
1 1000P (SWITCHING)
R3869
OPEN
4
GND
3 2 1
MUTE
IC3851
BH3547F
C3861
0.1
1 R3823
C3871
2200P
12
13 NU
14 PBTL
17
PVCCR 16
PVCCR 15
OPEN
C3806
OPEN L3804
10uH
1000P 1 OPEN 1
2
3
4
SP(L)+
SP(L)-
SP(R)-
SP(R)+
OPEN SP3802
C3831 C3826 C3829 R3804 C3814 C3823 D3804 SPEAKER
100/16V 100/16V 100/16V OPEN 1000P 1 OPEN R-CH
C3810
OPEN
Y Z AA BB CC DD
10-18 PL13.11BSCD5
CONTINUE
DIGITAL 4 HDMI-
P-ON+3.3V JK3002 CONNECTOR-2
C3316 C3421 C3423 C3425 C3426 1 TMDS-D2(+)
AL+3.3V 10 1 1 1 1 2 D-SHIELD0
P-ON+3.3V(1)
3 TMDS-D2(-)
P-ON+5V
D3993 C3420 C3422 C3424 C3427 4 TMDS-D1(+)
OPEN OPEN OPEN OPEN OPEN
5 D-SHIELD1
6 TMDS-D1(-)
7 TMDS-D0(+)
4 *1
IC3005(6/6)
R8A05011BG-U0
DIGITAL SIGNAL PROCESS
8
9
10
11
D-SHIELD2
TMDS-D0(-)
TMDS-CLOCK(+)
C-SHIELD0
/MAIN MICRO CONTROLLER Q3014
2SK3018 R3405 12 TMDS-CLOCK(-)
(BUFFER) 100
13 HDMI-CEC
TO DIGITAL TO DIGITAL 14 NU
MAIN 2 MAIN 5 R3415
IC3005(2/6) IC3005(5/6) 82K R3486 15 HDMI-CLOCK
3.9K 16 HDMI-DATA
D3057 IC3018 C3202 C3203 R3275 R3278 17 GND
VIDEO AUDIO RB751S-40 OPEN OPEN 47K 47K
DECODER DECODER 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 TMDS351PAGR
R3237 (HDMI SW) 18 +5V
NU
GND
VCC
GND
VCC
GND
27K C3023 R3066 R3055 19 HOT PLUG DETECT
HDMI-CEC B15 0.1 2.7K 1K
17 HOT-PLUG- 64 Q3008
DETECT3 R3063 2SC4081UBTLQ
18 63 1K (SWITCHING)
C3989 C3988 R3489 R3058
B1 OPEN OPEN 10K 19 VCC 62 10K
A1
20 VCC 61 HDMI-
B2 JK3003 CONNECTOR-3
A2 21 60 1 TMDS-D2(+)
HDMI
I/F B3 C3987 C3986 2 D-SHIELD0
OPEN OPEN 22 GND 59
A3 3 TMDS-D2(-)
B4 23 GND 58 4 TMDS-D1(+)
A4 5 D-SHIELD1
3 C3985
OPEN
C3984
OPEN
24
25 VCC
26
HDMI SW 57
56
VCC 55
6
7
8
TMDS-D1(-)
TMDS-D0(+)
D-SHIELD2
C3990 9 TMDS-D0(-)
1P 27 54 10 TMDS-CLOCK(+)
R3488 R3487
4.7K 4.7K 11 C-SHIELD0
28 GND 53
12 TMDS-CLOCK(-)
SCL-SINK C16 29 SCL-SINK 52 13 HDMI-CEC
14 NU
SDA-SINK C15 30 SDA-SINK 51
R3514 15 HDMI-CLOCK
100
HPD-SINK F13 31 HOT-PLUG-
DETECT-SINK
HOT-PLUG- 50
DETECT2 16 HDMI-DATA
R3508 C3204 C3205 R3214 R3212
22 17 GND
HOT-PLUG-
GND
VCC
0.1 2.7K
NU
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Q3001
R3509 R3018 2SC4081UBTLQ
22 1K (SWITCHING)
HDMI-SEL1 F1
R3497 R3017
4.7K R3992 10K
R3990 0
OPEN HDMI-
R3236 C3185 R3270 C3187 JK3004 CONNECTOR-1
560 0.01 2.2K 2.2 R3991 1 TMDS-D2(+)
10K
EXT-RES C4 C3186 2 D-SHIELD0
2 PLL-XFC-A B5
PLL-XFC-P A5 R3271
3K
4700P
C3188
2200P
3
4
5
TMDS-D2(-)
TMDS-D1(+)
D-SHIELD1
6 TMDS-D1(-)
7 TMDS-D0(+)
8 D-SHIELD2
9 TMDS-D0(-)
10 TMDS-CLOCK(+)
PWR M12 11 C-SHIELD0
R3193 12 TMDS-CLOCK(-)
4.7K
HDMI-SCL G14 13 HDMI-CEC
HDMI-SDA F14 D3003 D3001 C3208
RB751S-40 RB751S-40 OPEN 14 NU
R3192
4.7K 15 HDMI-CLOCK
16 HDMI-DATA
C3206 C3207 D3002 R3273 R3276 17 GND
CONTINUE OPEN OPEN RB751S-40 47K 47K
DIGITAL 5 18 +5V
HPD-SINK R3022 R3024 C3018 R3040 R3025 19 HOT PLUG DETECT
10K 10K 0.1 2.7K 1K
PWR
R3023
IC3011 22K Q3002
BU9883FV-WE2 2SC4081UBTLQ
(HDMI SERIAL EEPROM) R3029 (SWITCHING)
CONTINUE 1K
DIGITAL 2
VGA-SDA 1 VCC1 VCC2 16 R3027
10K
1 VGA-SCL
R3451
10K
R3453
1.5K
2 SCL1
3 SDA1
4 WPB
SCL2 15
SDA2 14
NU 13
R3073
0
R3074
0
C3192 0.1 R3075
R3281 5 VCC-OUT GND 12 0
Q3451 100
2SC4081UBTLQ 6 SDA0 SDA3 11 R3076 R3078
(SWITCHING) R3282 0 OPEN
R3452 100
10K 7 SCL0 SCL3 10 R3081 R3080
0 OPEN
8 VCC0 VCC3 9
DIGITAL MAIN CBA UNIT C3191
0.1
EE FF GG HH II JJ
10-19 PL13.11BSCD6
4 R3211
OPEN
R3213
D3202
OPEN
Q3007
2SC4081UBTLQ
(SWITCHING) C3000
OPEN
R3048
1K
CELL-PWR-CTRL
VCOM-PWM
P-ON-H2
OPEN PROTECT3
D3204
C3204 R3085 OPEN
OPEN OPEN
D3201
OPEN
Q3201 CONTINUE
OPEN DIGITAL 2
S D PANEL-VCOM-PWM
IC3201 C3208 C3209 C3207 C3214 C3257 R3283 C3258
OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN G R3284 CELL-PWR-CTRL
C3201 OPEN
OPEN LCD+12V
C3235 1 SS BST 8
OPEN R3217 R3281
0 Q3202 OPEN
2 EN IN 7 OPEN
R3202 C3203 C3202 R3282 C3256
OPEN OPEN OPEN Q3282 OPEN OPEN
3 COMP SW 6 C3282 OPEN
R3215 OPEN
4 FB GND 5 OPEN L3201 1 8
R3209 R3208 OPEN
OPEN OPEN R3205 C3206 2 7
OPEN OPEN R3291
OPEN
3 6 R3286
OPEN TO LCD PANEL
R3218 R3216 D3203 C3210 C3205 C3212 C3213 C3211 4 5 CN3013 ASSEMBLY
OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN R3289 1 NU
OPEN R3287 C3170 C3171 2 NU
Q3281 OPEN OPEN OPEN
CONTINUE OPEN 3 NU
DIGITAL 2 C3281 R3288 4 NU
OPEN OPEN
3 LVDS-OD0(-)
LVDS-OD0(+)
LVDS-OD1(-)
LVDS-OD1(+)
R3172
OPEN 5
6
7
NU
GND
GND
8 GND
LVDS-OD2(-) R3251 0
9 NU
LVDS-OD2(+) R3252 0
10 NU
LVDS-OCLK(-) 11 NU
LVDS-OCLK(+) 12 NU
LVDS-OD3(-) 13 LVDS-OD3(+)
LVDS-OD3(+) 14 LVDS-OD3(-)
15 GND
16 LVDS-OCLK(+)
*1
IC3001(1/5) 17 LVDS-OCLK(-)
MSD8200DS-S1 18 GND
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER 19 LVDS-OD2(+)
20 LVDS-OD2(-)
21 LVDS-OD1(+)
R3249 OPEN 22 LVDS-OD1(-)
98
R3248 OPEN 23 LVDS-OD0(+)
97 24 LVDS-OD0(-)
R3253 0
100 25 GND
R3254 0
99 26 GND
27 NU
102
2 101
104
28
29
30
31
NU
LVDS-ED3(+)
LVDS-ED3(-)
GND
103 32 LVDS-ECLK(+)
106 33 LVDS-ECLK(-)
105 34 GND
35 LVDS-ED2(+)
LVDS 108 36 LVDS-ED2(-)
TX
107 37 LVDS-ED1(+)
R3153 OPEN 38 LVDS-ED1(-)
113
R3149 OPEN 39 LVDS-ED0(+)
112 40 LVDS-ED0(-)
R3145 OPEN
115 41 GND
R3143 OPEN R3165 0
114 42 GND
R3166 0
R3142 OPEN 43 P-ON+3.3V
117 R3129 R3167 0
R3168 OPEN 44 P-ON+3.3V
R3141 OPEN 0
116 45 VCOMA
R3140 OPEN 46 DCDC-EN
119 R3169 R3170 0
R3139 OPEN 0 R3130 47 GND
118 OPEN R3173 0
48 LCD+21V
R3137 OPEN R3174 0
121 R3171 49 LCD+21V
R3111 OPEN 0
1 120
123
122
R3110 OPEN
R3109 OPEN
C3167
1000P
C3166
4.7 R3099
0
50
51
LCD+21V
GND
OPEN
OPEN
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
2 GND
3 NU
C3661
C3662
C3663
C3664
C3665
C3666
C3667
C3668
C3669
C3670
C3671
C3672
C3673
C3674
C3675
C3676
C3677
C3678
C3679
C3680
C3681
C3682
C3683
C3684
TO DIGITAL
MAIN 4 4 NU
IC3001(3/5)
A B C D E F
10-20 PL13.11CSCD1
CONTINUE
DIGITAL MAIN CBA UNIT DIGITAL 1
PANEL-VCOM-PWM
CELL-PWR-CTRL
R3039 LCD+12V
OPEN
R3035
OPEN
CN3001 (NO CONNECTION)
4 C3514
OPEN
C3513
OPEN
31
30
29
LCD+12V
LCD+12V
LCD+12V
R3028 28 GND
OPEN R3037 OPEN
27 VCOM-PWM
C3918 C3921 C3916 C3914 C3915 C3923 C3924 C3919 C3512 26 PWR-CTRL
OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN
D3905 25 P-ON+3.3V
OPEN R3038 OPEN
24 GND
R3924 23 LLV0(+)
OPEN R3907 22 LLV0(-)
C3917 OPEN
OPEN R3919 R3920 R3923 21 LLV1(+)
OPEN OPEN OPEN R3913
OPEN 20 LLV1(-)
19 LLV2(+)
R3917 18 LLV2(-)
OPEN OPEN
17 GND
16 LLVCNK(+)
OPEN R3916
OPEN 15 LLVCLK(-)
14 GND
CONTINUE IC3902 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 13 LLV3(+)
DIGITAL 1 OPEN 12 LLV3(-)
VDDC(1.2V)
VDDP(3.3V)
(3.3V)
VDDP(3.3V)
GND
GND
REL
GND
NU
NU
LVDS-OD0(-)
3
MGD-EN
VDDP
/GP08
LVDS-OD0(+) 11 LLV4(+)
LVDS-OD1(-) 10 LLV4(-)
LVDS-OD1(+) 1 48 9 LLV5(+)
R3931
LVDS-OD2(-) OPEN 8 LLV5(-)
2 SERIAL 47
LVDS-OD2(+) I/F 7 GND
LVDS-OCLK(-) 3 46 6 TP
R3932
LVDS-OCLK(+) OPEN 5 POL
4 45
LVDS-OD3(-) 4 CPV
LVDS-OD3(+) 5 VDD-LVDS CONTROL SIGNAL GENERATOR 44 3 OE1
LVDS 2 OE2
6 OUTPUT 43
R3933 LVDS 1 STV
OPEN RX
7 42
CN3006 (NO CONNECTION)
8 41 30 LCD+12V
R3934
OPEN 29 LCD+12V
9 40
DATA DATA 28 GND
10 INPUT PROCESSING 39 27 VCOM-PWM
R3935 LATCH
OPEN 26 PWR-CTRL
11 38
25 P-ON+3.3V
12 GND 37 24 GND
2 R3928
OPEN
C3920
13 VDDC(1.2V)
14 RESET
OPEN 15 GND
GND 36
35
R3910 OPEN
R3908 OPEN
23
22
21
20
LLV0(+)
LLV0(-)
LLV1(+)
LLV1(-)
34
R3921 19 LLV2(+)
UD-SEL/GP02
VDDC(1.2V)
VDDP(3.3V)
VDDP(3.3V)
16 LV-SEL 33
PWMO/GP06
18 LLV2(-)
KB/GP01
R3922 17 GND
OPEN
TSET
16 LLVCNK(+)
NU
NU
NU
NU
NU
15 LLVCLK(-)
CONTINUE 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
DIGITAL 5 14 GND
P-ON+3.3V 13 LLV3(+)
R3914 OPEN
VDDC+1.26V 12 LLV3(-)
C3913 L3901 C3902 C3922 C3925 R3912 OPEN
OPEN OPEN OPEN OPEN OPEN 11 LLV4(+)
R3926 R3909 OPEN
OPEN 10 LLV4(-)
9 LLV5(+)
R3906 R3927 8 LLV5(-)
OPEN OPEN 7 GND
R3904 R3925 6 TP
OPEN OPEN 5 POL
CONTINUE 4 CPV
DIGITAL 5
1 BACKLIGHT-ADJ
BACKLIGHT-DIM
3
2
1
OE1
OE2
STV
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
R3041
R3132
R3120
R3119
R3118
R3117
C3165
C3102
C3164
C3163
C3162
C3161
G H I J K L
10-21 PL13.11CSCD2
4 MDQU7
XOUT 66
XIN 67
R3158
OPEN
X3101
24MHz C3172
18P
153 MDQU7
IC3002 MDQU6 144 MDQU6
K4T51163QJ-BCE7 MDQU5 157 MDQU5
(DDR2 SDRAM) MDQU4
C3223 0.1 142 MDQU4 R3196 R3189
*A VDD MDQU3 141 MDQU3 10K 33K
C3224 0.1 VREF J2 MDQU2 155 MDQU2
C3225 0.1 C3222 R3232 R3234 R3233 C3217
0.1 1K 56 56 0.01 MDQU1 143 MDQU1
C3226 0.1
MDQU0 154 MDQU0 TO DIGITAL Q3103
C3227 0.1 CKE K2 MAIN 4 2SA1576UBTLQ
MDQL7 158 MDQL7 IC3001(3/5)
C3228 0.1 CK J8 (SWITCHING) R3197
E2 NU MDQL6 139 MDQL6 33K
C3229 0.1 CK K8 R3210
A2 NU MDQL5 162 MDQL5 OPEN
C3218 0.1 CS L8
R7 NU MDQL4 136 MDQL4
C3216 0.1 RAS K7 R3193
R3 NU MDQL3 137 MDQL3 10K R3161
C3220 0.1 CAS L7 100
MDQL2 161 MDQL2
C3221 0.1 WE K3
1-O3 B7 UDQS MDQL1 138 MDQL1
C3215 0.1 BA2/NU L1 CONTINUE
2-O3 A8 UDQS/NU MDQL0 160 MDQL0 I2S-OUT-MCK 132 R3150 DIGITAL 5
C3219 10 BA1 L3 OPEN R3177
3-O3 B3 UDM 3-M3 145 SD-UDM R3195 OPEN Q3101 PROTECT1
C3230 OPEN BA0 L2 OPEN OPEN
3 C3231
C3232
C3233
OPEN
OPEN
OPEN
MDQU7
MDQU6
MDQU5
MDQU4
B9
B1
D9
MDQU7
MDQU6
MDQU5
A13
A12
A11
R8
R2
P7
6-M3
2-M3
1-M3
5-M3
152 SD-LDM
150 SD-UDQSN
149 SD-UDQS
PROTECT3
BACKLIGHT-ADJ
BACKLIGHT-SW
134
129
75
R3160
10K
R3191
R3199
1K
C3175
PROTECT3
P-ON-H2
BACKLIGHT-ADJ
BACKLIGHT-SW
C3234 OPEN D1 MDQU4 A10/AP M2 148 SD-LDQSN R3106 22 10K OPEN
MDQU3 D3 MDQU3 4-M3 147 SD-LDQS PROTECT1 209 RESET
A9 P3 R3101 10
MDQU2 D7 MDQU2 P-ON-H2 206
A8 P8 R3238 75 R3155
MDQU1 C2 MDQU1 177 SD-A11 OPEN
A7 P2 R3220 75x4
MDQU0 174 SD-A4 CONTINUE
C8 MDQU0 A6 N7 DIGITAL 1
4-O3 170 SD-CAS R3162 100
F7 LDQS A5 N3 CELL-PWR-CTRL 76 CELL-PWR-CTRL
5-O3 E8 LDQS/NU 172 SD-A2 VCOM-PWM
6-O3 A4 N8 171 SD-A0 R3156
F3 LDM A3 N2 R3221 75 OPEN Q3102 P-ON-H2
MDQL7 F9 MDQL7 183 SD-A10 OPEN PROTECT3
A2 M7 R3229 75 R3159
MDQL6 F1 MDQL6 182 SD-A1 10K
A1 M3 R3237 75
MDQL5 H9 MDQL5 180 SD-BA1 R3188
A0 M8 R3222 75 100
MDQL4 H1 MDQL4 179 SD-WE VCOM-PWM 83
ODT K9 R3236 75
MDQL3 H3 MDQL3 181 SD-BA0 R3163 CONTINUE
VSS *B R3204 75 10K DIGITAL 5
MDQL2 H7 MDQL2 191 SD-BA2
R3227 75 TO DIGITAL DDR+1.8V
MDQL1 G2 MDQL1 190 SD-A3 MAIN 4
R3228 75x4 IC3001(3/5) P-ON+3.3V
MDQL0 G8 MDQL0 188 SD-A12
187 SD-A9 AL+3.3V
2 *A:A1,A9,C1,C3,C7,C9,E1,E9,
G1,G3,G7,G9,J1,J9,M9,R1
*B:A3,A7,B2,B8,D2,D8,E3,E7,
F2,F8,H2,H8,J3,J7,N1,P9
R3203
R3235
75
75
184 SD-A5
192 SD-CKE
189 SD-A7 AMP-MUTE 127
R3355
OPEN
CONTINUE
DIGITAL 4
BACKLIGHT-SW
AMP-MUTE
R3223 75 C3189
169 SD-RAS OPEN
R3240 75
175 SD-A6
R3224 75
168 SD-ODT
R3239 75
IC3006 176 SD-A8
W25Q32FVSSIG R3102 R3225 75 L3101
4.7K 164 SD-CLK 22uH
(MEMORY) R3226 75 AUVRM 51
R3089 33 165 SD-CLKN C3120 10
1 CS VCC 8 C3073 R3230 75 AUVRP 52
0.1 178 SD-A13 C3121 0.1
R3092 33 C3123 4.7
2 SO NU 7 202 WP AUVAG 53
R3154 33 R3094 33 204 CS C3133 1
3 WP SCL 6
201 SOUT C3101 1
R3194 R3093 33 NU 207
OPEN 4 GND SDA 5 200 SPI-SDA
R3107 199 SPI-SCL
10K
216 STB-RESET
R3242 C3110
OPEN OPEN
1 R3178
220
IC3009
PST8429UR
(RESET)
R3182
56K
D3109
OPEN
R3219
10K
R3241
100 Q3104
1 GND OUT 4 2SC4081UBTLQ
C3116 D3110 (SWITCHING)
2 VDD CD 3 1000P OPEN
C3252 D3108 C3106 C3113
OPEN OPEN 1 0.033
M N O P Q R
10-22 PL13.11CSCD3
COMPONENT A/D
-Pb-IN C3702 R3125 CONVERTER
10P 75 R3354 33
133 COMP-DET
R3144 33 C3118 0.047
COMPONENT 38
-Pr-IN C3703 R3127 R3136 33 C3139 0.047
34
4 R3715
0
10P
C3188
75
C3708
0.1
R3710
100
R3711
7.5K
C3717
OPEN
C3707
1
C3714
OPEN
R3200
R3123
R3138
R3124
R3128
0
33
68
68
C3119
C3140
C3141
C3124
1000P
0.047
0.047
0.047
35
36
37 NU
TO DIGITAL
MAIN 3
100P 10K SW IC3001(2/5)
Q3701 45 NU
C3706 R3709 R3712 C3716
JK3701 1 220 2SC4081UBTLQ 10K OPEN 26 VGA-HSYNC
DIGITAL (BUFFER) R3122 33 C3136 0.047 TO DIGITAL
AUDIO OUT 27
(COAXIAL) C3709 C3715 R3708 R3135 33 C3135 0.047 MAIN 3
100P OPEN 100 29 DIGITAL IC3001(2/5)
R3706 R3146 R3147 R3131 0 C3137 1000P
10K 75 75 28 SIGNAL
R3121 68 C3117 0.047 PROCESS
AUDIO(L)-IN 30 TO DIGITAL
C3720 R3713 C3718 R3134 33 C3134 0.047 MAIN 6
330P 12K 560P 31
R3707 IC3001(5/5)
10K R3148 32 VGA-VSYNC
75
AUDIO(R)-IN C3719 R3714 C3713 TO DIGITAL
330P 12K 560P MAIN 6
IC3001(5/5)
JK3001
C3013 OPEN
PC-RGB-IN
C3019 10P
3 4
5
9
10 15
14
R3343 100
R3198 100
130 SPDIF
AP2151WG-7
(HIGH SIDE SW)
1 OUT IN 5
C3327
1
C3125 2.2 2 GND
D3302 1SS400
47
C3014 OPEN
R3321 4.7K
R3326 4.7K
D3041 OPEN
D3054 OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
C3020 10P
C3126 2.2
10P
10P
10P
10K
10K
48 VBUS-ST 80 3 /FLAG RN 4
TO DIGITAL R3176 22
VBUS-EN 82 R3479
MAIN 6 10K
D3049
D3053
D3045
D3055
D3050
C3009
C3007
C3002
C3015
C3016
C3017
R3347
R3358
IC3001(5/5)
C3148 330P
R3175 220K
C3147 330P
R3164 220K
R3480
AUDIO 10K
D3301 I/F
1SS400 R3016
R3014 R3015 0 TO DIGITAL
(NO CONNECTION) CN3010 OPEN OPEN 60 MAIN 6
P-ON+5V 1 C3018 61 IC3001(5/5)
OPEN
UART0-TX 2 64
UART0-RX 3 63
GND 4 C3253 C3254 C3255
R3395 R3396 OPEN OPEN OPEN
CONTINUE OPEN OPEN
DIGITAL 5
P-ON+3.3V
AL+3.3V
P-ON+5V
AMP+13V
R3811 R3720 Q3702 R3705
10K OPEN OPEN 10K
CONTINUE
DIGITAL 6
2 UARTRXD0
UARTTXD0
R3809
10K
R3810
OPEN
D3704
OPEN
C3724
OPEN
C3723
OPEN
R3726 R3722
R3721
OPEN
Q3703
OPEN
OPEN OPEN
R3813
0 IC3801 R3723
R3821 R3820 TPA3110D2PWPR OPEN
OPEN 10 (AUDIO AMP)
R3814 Q3803 L3701 R3716 C3705 R3725
10K OPEN 10uH OPEN 220/6.3V OPEN
1 PVCCL 28 JK3703
CONTROL C3721 R3701 R3718 R3704 HEADPHONE
2 LOGIC PVCCL 27 0.01 OPEN OPEN 1K JACK
R3818 R3819 C3805 1 C3801 0.22 D3707 D3706 D3708 C3704
OPEN OPEN 3 26 C3711 OPEN OPEN OPEN 1
POWER PWM OPEN
C3818 1 LIMIT LOGIC DRIVE C3710 D3702 D3701 D3703
4 25 L3702 R3717 R3724
220/6.3V OPEN OPEN OPEN OPEN
10uH OPEN
CONTINUE R3805 OPEN
DIGITAL 3 R3816 5 GND 24 C3824 C3825 C3832
OPEN Q3802 0.047 2.2 10 L3801 C3722 R3703 R3719 R3702
BACKLIGHT-SW GAIN 10uH 0.01 OPEN OPEN 1K
OPEN R3806 0 CONTROL
AMP-MUTE R3817 6 23
OPEN DRIVE R3801 C3811 C3820 C3836 C3837 D3801 C3712
C3802 0.22 OPEN 1000P OPEN OPEN 1 OPEN OPEN
7 AVCC 22
C3807
C3830 R3815 C3815 R3807 OPEN C3803 0.22 OPEN L3802
0.1 100K 1 8 GND 21 10uH
C3816 1 DRIVE
9 GVDD 20 R3802 C3812 C3821 C3838 C3839 D3802
R3808 OPEN 1000P 1 OPEN OPEN OPEN
C3817 1 10K C3827 C3828 C3833
R3812 10 GND 19 0.047 2.2 10 C3808
10K Q3801 OPEN L3803
2SC4081UBTLQ C3819 1 10uH SP3801
11 18
1 D3806
1SS400
(SWITCHING)
C3806 1
12
13 NU
POWER
LIMIT
PWM
LOGIC DRIVE
17
PVCCR 16
C3804 0.22 R3803
OPEN
C3809
OPEN L3804
C3813
1000P
C3822
OPEN
C3841
OPEN
C3842 D3803
1 OPEN
CN3801
1 SP(L)+
2 SP(L)-
3 SP(R)-
SPEAKER
L-CH
D3805 10uH
1SS400 14 PBTL PVCCR 15 4 SP(R)+ SP3802
C3831 C3829 R3804 C3814 C3823 C3843 C3844 D3804 SPEAKER
220/16V 100/16V OPEN 1000P 1 OPEN OPEN OPEN R-CH
C3810
OPEN
S T U V W X
10-23 PL13.11CSCD4
CONTINUE
DIGITAL 3 DIGITAL MAIN CBA UNIT
PROTECT1
R3633 100
PROTECT3
IC3602
P-ON-H2 AP1117EG-13
R3631 100 (+3.3V REG.)
BACKLIGHT-ADJ
R3632 100
VOUT
BACKLIGHT-SW
COM
VIN
4 CONTINUE
DIGITAL 2
BACKLIGHT-ADJ
BACKLIGHT-DIM
R3629 OPEN
R3637
OPEN
C3604
OPEN
C3603 D3602
OPEN OPEN
C3644
OPEN
10 100 10 220/6.3V
D3607 C3650 R3605
(NO CONNECTION) CN3601 OPEN OPEN 33
LED-CONT(NU) 1 IC3601 *1
AP1117EG-13 R3604 IC3001(4/5)
PROTECT1 2 220
(+2.5V REG.) MSD8200DS-S1
PROTECT3 3 DIGITAL SIGNAL PROCESS
VOUT
COM
VIN
3 GND 19
P-ON+21V 20
P-ON+21V 21
C3613
10
C3611
220/6.3V
R3646
OPEN
C3687
OPEN
R3643
47K
OPEN
L3102
22uH
C3112
0.1
166 AVDD-PLL
P-ON+21V 22 39 AVDD-ADC25
R3644 C3128
P-ON+21V 23 10K R3642 0.1
R3645 100 L3103
10K Q3603 22uH
2SC4081UBTLQ 54 AVDD-AU25
TO POWER SUPPLY C3633 (SWITCHING) C3129
CBA CN501 CN3602 IC3605 1 0.1
LED-CONT(NU) 23 RT8293ALZSP L3107
(+1.26V REG.) 22uH
PROTECT1 22 C3627 69 AVDD-ADC25
0.047 C3154
PROTECT3 21 1 BS SS 8 0.1
C3628 L3105
RESET 20 0.1 22uH
2 VIN EN 7 72 AVDD-PGA25
BACKLIGHT-SW 19 C3626 C3637 C3601 R3641 C3686 L3106 C3152
P-ON-H2 18 0.01 4.7 0.1 3 SW COMP 6 10K OPEN 22uH 0.1
C3629 L3109 73 PGA-COM
BACKLIGHT-ADJ 17 4 GND FB 5 0.01 22uH
AL+3.3V 16 R3625 110 AVDD-MOD
8.2K R3624 R3619 C3184
GND 15 C3647 C3646 C3660 C3651 R3654 Q3605 R3653 16K 2K 0.1
OPEN OPEN 10 OPEN 10 R3656 2SA1576UBTLQ 1K C3640 C3624 C3625 R3626
GND 14 22K (SWITCHING) OPEN OPEN OPEN L3603 1K
10uH
GND 13 25 VDDC
GND 12 R3655 R3627 C3632 C3635 C3634 C3622 C3636 D3606 R3623 C3127 C3131 C3151 C3185 33 AVDDL-ADC
C3658 C3659 D3611 D3610 10K OPEN 220/6.3V 10 10 10 10 PTZTE255.1B OPEN 0.1 0.1 0.1 0.1
GND 11 OPEN 1 OPEN MM5Z4V3B R3652 R3638 84 VDDC
Q3606 10K OPEN C3642
GND 10 2SC4081UBTLQ OPEN 111 AVDDL-MOD
AMP+13V 9 (SWITCHING) R3651 D3011 R3007 124 VDDC
22K MM5Z7V5B 100K C3176 C3186 C3107
AMP+13V 8 C3648 C3645 C3649 0.1 0.1 0.1 156 DVDD-DDR
2 AMP+13V
AMP+13V
GND
7
6
5
0.1 OPEN OPEN R3108
2K R3133
OPEN
D3012
1SS400
R3098
10K
Q3005
2SA1576UBTLQ
(SWITCHING)
R3008
193 VDDC
P-ON+21V 4 22K
P-ON+21V 3 R3097
56K Q3006
P-ON+21V 2 2SC4081UBTLQ
R3005 C3011 (SWITCHING)
P-ON+21V 1 100K 1
IC3604
CONTINUE C3656 C3655 C3657 RT8293ALZSP
DIGITAL 1 OPEN 0.1 OPEN (+5V REG.) C3617 R3100
P-ON21V 0.22 OPEN L3110
1 BS SS 8 OPEN
P-ON+3.3V C3618 12 AVDD-DVI NU 41
0.1 C3103 C3132 C3160 C3114
P-ON+5V 2 VIN EN 7 10 0.1 0.1 0.1 90 AVDD-DVI-PC NU 42
C3615 C3652 C3616 C3010 R3618 C3630 203 AVDD-ALIVE NU 43
CONTINUE 0.01 0.1 OPEN 3 SW COMP 6 OPEN 47K OPEN
DIGITAL 2 L3111 NU 44
C3619 D3609 OPEN
P-ON+3.3V 4 GND FB 5 4700P 1SS400 40 AVDD-CVBS NU 46
VDDC+1.26V R3615 R3614 R3603 C3130
20K 10K 5.1K L3112 0.1 NU 49
CONTINUE C3639 C3607 Q3601 OPEN NU 50
DIGITAL 3 4.7 4.7 R3616 2SC4081UBTLQ 59 AVDD-AU33
L3602 33K R3621 (SWITCHING) NU 55
DDR+1.8V 10uH 20K C3158
L3114 0.1 NU 56
P-ON+3.3V R3628 C3620 C3621 C3623 C3638 D3608 C3641 R3620 OPEN
AL+3.3V OPEN 220/6.3V 10 10 OPEN OPEN OPEN 1K 68 AVDD-DMPLL NU 57
C3159 NU 58
C3643 L3113 0.1
CONTINUE OPEN OPEN NU 167
DIGITAL 4
1 P-ON+3.3V
AL+3.3V
P-ON+5V
C3157
0.1
65 AVDD-EAR33
62 GND
77 GND
NU
NU
NU
185
196
197
AMP+13V 198 GND
CONTINUE
DIGITAL 6
P-ON+5V
P-ON+3.3V
AL+3.3V
AL+3.3V(1)
Y Z AA AB AC AD
10-24 PL13.11CSCD5
MSD8200DS-S1
IF-AGC
+3.3V
4 C3927
C3926
33P C3173
0.1 R3151
33
C3145
OPEN
C3144
L3108
OPEN R3181
51
C3142
0.1
70
DEMODULATOR
/MPEG
DECODER
VIN
8 13 HDMI-CEC
1 2 3 126 TU-SCL HDMI 7 14 ARC
125 TU-SDA I/F
5 15 HDMI-CLOCK
C3912 4 16 HDMI-DATA
OPEN 3 R3003 R3001 17 GND
R3903 C3911 C3907 10K 10K
100 10 220/6.3V R3179 2 18 +5V
R3902 0 R3042 100
33 74 IF-AGC 9 D3005 D3004 R3422 C3404 R3420 19 HOT PLUG DETECT
C3168 R3180 R3050 100 RB751S-40 RB751S-40 47K 0.1 1K
0.022 10K 6
R3901
3 220
L3104
22uH
C3149
95
94
92 R3056 OPEN
R3421
1K Q3407
(SWITCHING)
R3423
2SC4081UBTLQ OPEN
JK3003
1
HDMI-
CONNECTOR-1
DATA2(+)
10 91
89 2 TMDS DATA2 SHIELD
R3536 Q3531 R3057 OPEN
0 OPEN R3417 R3104 88 3 DATA2(-)
10K 22 R3062 OPEN
211 WAKE 87 4 DATA1(+)
86 5 TMDS DATA1 SHIELD
R3535 R3022 100 R3064 OPEN
OPEN R3534 96 6 DATA1(-)
OPEN R3023 100 R3065 OPEN
R3353 93 7 DATA0(+)
CONTINUE 0 8 TMDS DATA0 SHIELD
DIGITAL 5 R3822 135 SW-EN R3067 OPEN
10 C3187 9 DATA0(-)
P-ON+5V OPEN R3069 OPEN
P-ON+3.3V C3555 10 CLOCK(+)
OPEN R3192
10K AUDIO VIDEO 11 TMDS CLOCK SHIELD
AL+3.3V R3503 DECODER DECODER R3070 OPEN
AL+3.3V(1) OPEN 12 CLOCK(-)
13 HDMI-CEC
TO FUNCTION CBA 14 NU
UNIT CN4052 CN3101 Q3502 TO DIGITAL TO DIGITAL 15 HDMI-CLOCK
2SA1576UBTLQ MAIN 4 MAIN 4
SDA(NU) 1 (LED DRIVE) IC3001(3/5) IC3001(3/5) 16 HDMI-DATA
R3103 22
SCL(NU) 2 215 REMOTE R3214 R3212 17 GND
R3552 R3116 4.7K 10K 10K
GND 3 100 205 LED1 18 +5V
R3113 100
KEY-IN1 4 R3558 HDMI-CEC 214 D3007 D3006 R3019 C3005 R3010 19 HOT PLUG DETECT
C3559 OPEN R3559 RB751S-40 RB751S-40 47K 0.1 1K
REMOTE 5 OPEN 10K
LED1 6 R3183 HDMI1-HPD 17 R3018 R3017
100 Q3010 1K Q3001
2 LIGHT
P-ON+5V
AL+3.3V
7
8
9
C3554 C3550
C3553
OPEN
C3556
OPEN
R3551 R3555
100 OPEN
C3557
OPEN
C3558
10
2SC4081UBTLQ
(BUFFER)
HDMI2-HPD 1
HDMI3-HPD 85
R3024 OPEN
2SC4081UBTLQ
(SWITCHING)
OPEN
JK3002
1
HDMI-
CONNECTOR-2
DATA2(+)
1 OPEN HDMI-ARC 24 2 TMDS DATA2 SHIELD
R3185 R3105 R3082 C3012 R3025 OPEN
10K 22 OPEN OPEN 3 DATA2(-)
R3560 208 LIGHT R3026 OPEN
Q3501 4 DATA1(+)
C3551 33P 2SC4081UBTLQ 100K R3184 R3186 C3191 C3115
(LED DRIVE) 10K 39K OPEN OPEN 5 TMDS DATA1 SHIELD
C3552 33P R3027 OPEN
210 KEY-IN1 6 DATA1(-)
R3029 OPEN
D3501 R3553 R3112 7 DATA0(+)
R3556 R3557 MM5Z5V6B 100 10K
10 10 8 TMDS DATA0 SHIELD
R3034 OPEN
R3501 4.7K 9 DATA0(-)
78 SCL R3036 OPEN
R3502 4.7K 10 CLOCK(+)
79 SDA 11 TMDS CLOCK SHIELD
R3040 OPEN
R3201 100 12 CLOCK(-)
131 FACTORY-SEL 13 HDMI-CEC
14 NU
15 HDMI-CLOCK
16 HDMI-DATA
R3278 R3275 17 GND
10K 10K
18 HDMI+5V
D3009 D3008 R3066 C3023 R3055 19 HOT-PLUG-DETECT
R3080 R3075 RB751S-40 RB751S-40 47K 0.1 1K
CONTINUE 10K 1K R3077
DIGITAL 4 OPEN
1 UARTRXD0
UARTTXD0
Q3004
2SA1576UBTLQ
R3071
10K
R3076
33K
Q3002
2SC4081UBTLQ
(SWITCHING)
R3063
1K Q3008
2SC4081UBTLQ
(SWITCHING)
R3058
OPEN
R3081 (SWITCHING)
100
C3003
R3078 330P R3243
Q3011 1K R3079 OPEN
2SC4081UBTLQ 10K
(SWITCHING) R3073 R3244
Q3003 10K OPEN
2SC4081UBTLQ R3245
(SWITCHING) R3074 OPEN
33K
AE AF AG AH AI AJ
10-25 PL13.11CSCD6
GP001
C617
BA31T0F0102 2 J241
NEUTRAL
C1008
P-ON+21V L1001 GND
F602 IC601
CN601
J233 P-ON+21V
C1010
IC602 J227
J259
J231
GND
GND
P-ON+21V
D660
LIVE
3
C1001
J226 AMP+13V
J104
FG
J263
J225 P-ON-H2
GND
2
R1018
C651
CN1001 10
J245
OVP1
J246 ILED2
C650
C652
C6
C604
C1002
03
STATUS
J261
C1026
COLD
J237 LDR1
C653
R601
11
D659
D1005
J234 P-ON+21V
GATE
J101
HOT
J236
L601
ISW1
J235
SA
60
P-ON+21V
SOURCE
D650 C667
J102
1
J249 BL-ADJ
JS602
C60
J255
6
LDO
R6
L1002
11
C668
C1009
D651
JS601
ILED4
BC601
D606A
J247
D60
R1
8
01
D652
P-ON+21V
P-ON+21V
BL-SW
J253
9
J202
BC602
J201
PROTECT3
J252
Q601
C1011
ILED6
J248
J224
GND
OVP2
J250
GND
J254
D653
D10
BL-ADJ
C614
06
D6
C655
2
07
J251
C612
D6
55 C1027
C654
J256 LDO
R605
PROTECT3
J258
R619
BL-SW
BC603 J244
J257
VIN
LDR2
J243
ISW2
J242
STATUS
J260
J203
L602
J204 GND
J205 GND R678
C605
J262
J206
JS606
JS605
C656
GP003 GND
AMP+13V
D6
02
J208
Q658
C611
J209
D6 RESET J220
01
ALL+3.3V
J210
J212
J200
GND
D662
P-ON+21V
BC604 GND
LED-CONT
C662
1
ALL+3.3V
J211
J219
J214
JS603
JS604
JS609
C602
R610
R602
J240
J239
J215 GP002
ALL+3.3V
GND
J218
C616
23
P-ON-H2
D603
RESET
C663
D604
CN501
22
A B C D
10-26 BA31T0F01022
J241
BA31T0F0102 2 J228
C617
T 2.5A L/250V
C1008
CN601
P-ON+21V J233 IC601
C1010
J227
Q653
IC602
J259
J231
C1014
GND
GND
P-ON+21V
D660
R675
3
C610
C1001
J104
R658
FG
J263
2
GND
Q621
R1012 D610
CN1001
J245
OVP1
ILED2 J246
03
D605 R622 C604
C1002
C6
D1021
R621
C1043
10
STATUS
J261
GATE
J101
R1022 C622 D609A
D1003
J236
L601
IC1001 R1050
ISW1
C623
Q602
C1032 J235
1
R1052 D621
60
SOURCE
P-ON+21V C667 D652A D650
SA
J102
R607 C608
R1001 D651A
C1016
D1050
D1022
C1033 T601
P-ON+21V J238
BL-ADJ J249
R1023 R606
JS602
R1002
J255
C1041 C606
LDO
D1023 C1007
1
L1002
1
C1037
R6
C1020
C668 D650A
C1009
D651
JS601
R1030
ILED4
BC601
J247
D606A
9
C1015 R1016 8
01
D60
C1013
D652
P-ON+21V
R1009
R1
P-ON+21V
BL-SW
R1037
J253
R1028
J202
J201
PROTECT3
BC602
R1027 R1017
J252
R1038
Q601
C1011
J224 D606
D608A
J250
OVP2
GND
GND
R1029 R1013
J254
D653
D1002
Q1002
06
D1024
BL-ADJ
C1023 C614
D10
07
C655
D6
2
R1024 D653A
IC1002 D1004 R603 C607
C1044
J251
R1025 R604
C612
R1042
C1025
C1035 C1040 C1042 C1027 55
D1025 C1017R1053 R1051 R1004 R1003 D6
LDO J256
C654
R605
PROTECT3
D655A
J258
R1026
R619
BL-SW
J244
J257
BC603 R614
VIN
C1036 D1051
LDR2
J243
J242
ISW2
D1026
J260
STATUS
C1021 R1008
J203
C1038
L602
GND J204
R1033 R1031 C630 R678 GND J205 C701
D656
C605
JS605
JS606
J206
C656
Q702 Q701
R694
D6
Q657A
D654
Q657
D656A
P-ON-H2 J207
J208
R670 D405 R677 R703 R651
R689 R704 R693
Q650
D657
Q658
C611
D663 R656
R663 D658
R686 R691
R671 D406 J209
Q658A
C664
Q659
D662
GND
P-ON+21V
R684 GND BC604
LED-CONT
C662 R682
1
ALL+3.3V
J211
J219
J214
JS603
JS604
JS609
C635
IC651
R680 R681
C661 C638 C602
C633 C639
R602
R610
J239
J240
GP002 J215
C636
ALL+3.3V
GND
J218
C616
23
1
P-ON-H2
D603
RESET
C663
D604
CN501
22
2
D C B A
10-27 BA31T0F01022
CL3801
1 4
TUNER UNIT
CN3801 CN3105 CN4052
1 9
COMPONENT CL3101
FUNCTION CBA UNIT
-Y/VIDEO-IN
9 1
COMPONENT
COMPONENT
-Pr-IN
AUDIO(L)-IN
REAR B W
CN601
AUDIO(R)-IN
DIGITAL
AUDIO-OUT CN3601 CN501
11-1
(COAXIAL)
1 1
CL3701
DIGITAL MAIN CBA UNIT POWER SUPPLY CBA
ETHERNET
JACK 23 23
HDMI-
CONNECTOR-1
WIRING DIAGRAM
CN1001
1 11
HDMI-
CONNECTOR-2
HDMI-
CONNECTOR-3
HEADPHONE
JACK
PL13.11AWI
SP3801 SP3802
SPEAKER SPEAKER
L-CH R-CH
[TYPE B]
CL3801
1 4
TUNER UNIT CN3101 CN4052
CN3801
1 9
CL3101
FUNCTION CBA UNIT
COMPONENT
-Y/VIDEO-IN
9 1
COMPONENT
-Pr-IN
REAR B W
AUDIO(L)-IN
CN601
AUDIO(R)-IN
CN3701 CN501
11-2
DIGITAL
AUDIO-OUT 1 23
(COAXIAL) CL3701
DIGITAL MAIN CBA UNIT POWER SUPPLY CBA
23 1
HDMI-
CONNECTOR-1
HDMI-
CN1001
CONNECTOR-2
1 11
HDMI-
CONNECTOR-3
SIDE PC-RGB-IN
CN3013
1
CL3011
USB JACK
LCD PANEL ASSEMBLY
51
HEADPHONE
JACK
PL13.11BWI
SP3801 SP3802
SPEAKER SPEAKER
L-CH R-CH
CL3801
[TYPE C]
1 4
AUDIO(L)-IN
REAR
B W
AUDIO(R)-IN CN601
DIGITAL
11-3
AUDIO-OUT
(COAXIAL)
CN3602 CN501
DIGITAL MAIN CBA UNIT
1 23 POWER SUPPLY CBA
HDMI- CL3701
CONNECTOR-1
23 1
HDMI-
CONNECTOR-2 CN1001
1 6
HDMI-
CONNECTOR-3
SIDE PC-RGB-IN
CN3013
1
USB JACK CL3011
PL13.11CWI
EXPLODED VIEWS
[TYPE A]
A1
LCD1
L9
A16 A4
A17
CL3011
L9
B23
[39PFL2608/F7, A13
39PFL2908/F7] B12
A6 A9 S7
L67
B17 L27
SP3802
L9
See Electrical Parts List
for parts with this mark.
SSK1
X6 L9
A15
S7
SNA1
SBA1
[39PFL2608/F7]
[39PFL2908/F7,
39PFL4408/F8]
SSK2
LCD1
L9
A16 A4
A17
CL3011
L9
B23
[39PFL2708/F7] A13
B12
A6 A9 S7
B18
L23
Function CBA Unit B17
L23
A3
AC601
L23 CL3801
L35
CL3101 B18
L23 B10
B19
SP3801
L9
L67
B17 L27
SP3802
A19
L9
See Electrical Parts List
for parts with this mark.
SSK1
L9
X6
A15
SNA1 S7
SBA1
SSK2
[39PFL2608/F7,
39PFL2708/F7,
39PFL2908/F7]
X2 X7
SSK1
S7
X3 X4 SSK2
[39PFL2708/F7,
39PFL2908/F7,
39PFL4208/F8,
[39PFL2608/F7] 39PFL4408/F8]
SNA1 Tape
S3
X1
S3
Packing Tape
[39PFL2608/F7]
SBA1
S6
S4
[39PFL2708/F7,
39PFL2908/F7,
39PFL4208/F8,
39PFL4408/F8]
S7
FRON
T FRO
NT
12-3 PL13.11_PEX
Downloaded from www.Manualslib.com manuals search engine
TYPE A
PARTS LIST [39PFL2608/F7 (Serial No.: DS1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a LCD PANEL ASSEMBLY
# have special characteristics important to safety.
Ref. No. Description Part No.
Before replacing any of these components, read
LCD1# LCD PANEL ASSEMBLY U30T1P1
carefully the product safety notice in this service
Consists of the following
manual. Don't degrade the safety of the product
A1 FRONT CABINET A31T2UH 1EM127996
through improper servicing.
A4 X -PCB COVER A31T0UH 1EM228323
NOTE: Parts that are not assigned part numbers A6 CONTROL PLATE A31F0UT 1EM334317
G.....±2% J......±5% K.....±10% R687 RES CHIP 3216 1/4W J 3.3 Ω RRX43R3HH034
R688 RES CHIP 3216 1/4W J 2.2 Ω RRX42R2HH034
M.....±20% N.....±30% Z.....+80/-20% R689 RES CHIP 3216 1/4W J 2.7 Ω RRX42R7HH034
R690# Not used
G.....±2% J......±5% K.....±10% R687 RES CHIP 3216 1/4W J 3.3 Ω RRX43R3HH034
R688 RES CHIP 3216 1/4W J 2.2 Ω RRX42R2HH034
M.....±20% N.....±30% Z.....+80/-20% R689 RES CHIP 3216 1/4W J 2.7 Ω RRX42R7HH034
R690# Not used
Chassis PL13.11
• 2013/02/28 39PFL2608/F7 (Serial No.: DS1) Added
• 2013/03/27 39PFL2708/F7 (Serial No.: DS2) Added
• 2013/04/19 39PFL2908/F7 (Serial No.: DS1) Added
• 2013/04/30 39PFL4208/F8 (Serial No.: XA1) Added
• 2013/06/05 39PFL4408/F8 (Serial No.: XA1) Added
• 2013/06/28 39PFL2608/F7 (Serial No.: DS2) Added
• 2013/08/17 39PFL2708/F7 (Serial No.: DS1) Added
14-1 PL13.11REV
Downloaded from www.Manualslib.com manuals search engine
COMPARISON LIST OF MODEL NAMES
Chassis PL13.11
39PFL2608/F7 (DS1) A3RTBUH TYPE A
PL13.11COM
Downloaded from www.Manualslib.com manuals search engine