Beruflich Dokumente
Kultur Dokumente
2. The slotted and castle nut with a split pin. The nominal length of the split pin is the distance from
a) Underside of the eye to the end of the short leg b) Underside of the eye to the end of the big leg.
c) Length of the big end with eyehole d) Length of the small and big ends with eye hole.
3. While assembling using bolt and nuts, we use the correct length of bolt. The nut is passed through mini
a) At least two threads on the bolt b) at least four threads on the bolt
c) At least five threads on the bolt d) at least six threads on the bolt
4. The screws used for light duty assembly works. These normally available...
7. The self-locking nut have a nylon or fibre ring insert the internal die of the ring insert is
a] Strollers than they are die of the bolt Thread b] Bigger than the core die of the bolt thread
c] Equal to core die of the bolt thread d] Double of the core of the bolt thread
c] Civet the clearance hole of the tab d] Improve the appearance of the tab
9. Which type of bolt is used when the assembly is sub costal to alternating load continual?
a) Body fit bolt b) Anti -fatigue bolt c) Square bolt d) Clearance hole bolt
10. The difference between maximum limit of size to its corresponding basic size of a component is...........
11. Why the woodruff keys are used on small tapered shafts with assembly?
a) It takes heavy load b) It takes the shear stress
c) It is easy to fit and self align with key way of hub d) It is less expensiv
12. The maximum clearance on the assembly shown in figure will be.................
15. Which type of washer is used for locking the nut by bending the washer against the side of the nut?
a) Tab washer b) Spring washer c) Locking plate d) Locking washer with lug
16. The pipe reamer is used to ream the pipe-Reaming is done after.................
a) pipe cutting b) pipe bending c) male thread cutting d) female thread cutting
17. The main advantage of using hexagonal socket head cap screw is to.............
C) have a very firm grip d) avoid the projection of the screw head above the surface
18. The length of rivet according to the thickness of the plates and dia of rivet. A formula L = t + 1.5 D generally
used in the shop floor.
What is the length of snap head rivet, if each plate thickness is 3 mm and rivet dia 6mm shown in the figure?
21. Which one of the following is the formula for size to form 100% thread?
22. Split taper pin have small end which is splitted as shown. The purpose of split provided in the split taper
pin is …
a) Easy to identify the small end b) To get spring action for locking
c) To ensure a more positive locking d) Easy to remove the pin while dismantle
23. The tolerance sizes of hole is and soft is in an assembly. The type of fit is ….
24. The flank angle and the form of fine screw thread can be checked by using.............
25. The figure given below is the roughness symbol of surface finish. This symbol indicates the roughness grade
of....................
a) Lap joint b) Single strap butt joint c) Double strap butt joint d) Double riveted lap joint
5. The bearing issue for plan bearing for slow speed with hardened shaft made of
a) Steel b) Cast iron c) Bronze d) White metal
6. Which type of bearing is used where slight angular misalignment or deflection between the bearing and the
support point occurs?
c] Civet the clearance hole of the tab d] Improve the appearance of the tab
9. Which range of cutting speed is set for turning a mild steel using H.S.S tool?
a) 15 - 20 m/min b) 35 - 50 m/min c) 50 - 80 m/min d) 70 - 100 m/min
10. A gap between two sheets was noticed after riveting. This defect is caused due to
a) short a rivet length b) over sized drilled hole
c) Improper use of rivet set d) the rivet being too long.
11. The taper provided in nose of the tail stock barrel is
12. Which angle of counter sink drill you will select for seating counter sink type A (IS-3406-1986)?
a) Counter sink drill 75° b) Counter sink drill 80° c) Counter sink drill 90° d) Counter sink drill 120°
13. Match the functions against the types of gauges. Functions of limit gauges
a) To check GO size only b) To check GO size of hole. C) To check NO GO size of shaft d) to check NO GO size of
hole
14. Match the BIS systems, of limits and fits, terms against the shaft dimensional values. BIS system of limits fits
terms
a) Lower deviation b) Maximum limit c) Minimum limit d) Basic size
15. The distance a drill moves into the work for ea revolution of the spindle is called the...
a) Feed of a drill b) speed of a drill c) depth of the drill d) cutting speed of a drill
18. 32. What will happen if the spindle thread is worn out in a gate valve?
c) Water flow around the stuffing box d) Value will not close or open when the spindle turns
a) To check the minor diameter of screw thread b) to check the limits of screw thread
c) To check the distance between adjacent crest of screw thread d) to check the major diameter of screw
thread
20. The operation of bevelling the end of a drilled hole. This operation is known as
a) Counter boring b) Counter sinking c) Spot facing d) Boring
21. Some hexagonal head screws are used in electrical work, head screws are made of
a) Copper b) Brass c) Steel d) Ceramics
22. The screws used for light duty assembly works. These normally available
a) Up to 10mm. thread dia. b) Up to 12mm. thread dia
c) Up to 8mm. thread dia. d ) Up to 11mm. thread dia.
23. Milling machine arbour is an example of
a) Self holding taper b) Quick Releasing taper c) Morse taper d) Metric tape
24. The grindings wheel is mounted on spindle using, Bolts, nuts and washers.
c) In the opposite (or) same direction to the direction of rotation of the spindle.
a) axial direction b) right angle, direction c) parallel axis, direction d) vertical axis, direction
3. Which are of the following springs resist a tensile load applied by means of a suitable end form hook or wop?
4. The self holding tapers have a smaller taper angle that is limited to maximum of
5. The taper ratio commonly used on morse taper in British system is—
7. In which follwoing start threads allows to keep the depth of the thread to be less and provides for rapid
axial movement of the screws.
a) Single start b) Multi start. C) Double Stan d) Both Single and Double Start.
a) Hexagonal socket screw b) Severe head screw c) Hexagonal head screw d) Pan head screw
9. A tap broken above the surface of the work piece, this brocken tap can be removed by using_
a) use of punch b) Use of cutting plier c) Use of tap extractor d) Use of arc welding
a) Light press fit b) Medium press fit c) Heavy drive fit d) Free fit
12. The hallow saddle key and circular taper key are used for
13.The operation of enlarging the end of a drilled hole for accomadating the socket head screw. Name the
operation
a) heavy duty external rings b) miniature high-strength rings c) inverted external rings d) Basic external rings
16. The "Ra" value can also be indicated in the corresponding roughness grade number. When only one "Ra"
value is specified, it represents the_
a) Max. permissible value of surface roughness. b) Min. Permissible value of surface roughness.
c) Between the Max. and Min. Permissible value of surface roughness d) length value of the surface roughness
17. Machined "T" bolts are to be protected against corrosion. The most suitable surface treatment for this is_
18. Which type lap abrasives are used for lapping tungston carbide?
19. The self-locking nut have a nylon or fiber ring insert the internal die of the ring insert is
a] Strollers than they are die of the bolt Thread b] Bigger than the core die of the bolt thread
c] Equal to core die of the bolt thread d] Double of the core of the bolt thread
20. Belt get slip in open belt drive, due to insufficient arc of contact of pulley. How do you reduce this type slip?
a) Put jockey pulley on slack side near smaller pulley b) Put jockey pulley on tension side near to smaller pulley
c) Put jockey pulley on slack side near to bigger pulley d) Put jockey pulley on tension side near to bigger pulley
21. The main advantage of using hexagonal socket head cap screw is to
c) have a very firm grip d) avoid the projection of the screw head above the surface
22. which severe is used to connect the collar and shaft in a passion
a) Hexagonal socket et screw b) Severe head screw c) Hexagonal head screw d) Pan head screw
22. Measuring gauges require wear resistance. Which heat treatment process is required to get such property?
23. The flank angle and the form of fine screw thread can be checked by using
24. Match the uses against with slip gauges accessories labelled in the figure. Uses
a) To measure the bore diameter of a bush b) To measure the external dimensions of a rectangular
block c) To scribe arc and circles while marking / layout work d) To check the height of a work setup
Slip gauge accessories
25. In which following metal, has it's most one important uses for electro plating metallic surfaces? a) Chromium
b) Nickel c) Stainless steel d) Aluminium
FITTER- III Rd SEMESTER
2. Couplings are used to connect the shaft, when the shafts are...............
3. Normal hardening temperature of less than 0.83% carbon plain carbon steel is..................
a) below the upper critical range b) above the upper critical range
c) below the lower critical range d) above the lower critical range
4. Screw threads of different forms are available for various uses. The trapezoidal threads are used..............
a) for coupling railway wagon b) for spindles of fly presses and screw jacks etc.
5. Which one of the following combination of movements are used to turn a ball on centre lathe with single point
tool?
a) Carriage and compound slide are used. b) Cross slide and compound slide are used.
c) Carriage and cross slide are used. d) Compound slide and apron are used.
6. Different feeds and different pitches of thread can be obtained on a centre lathe by using
a) Back gear b) Quick change gear box c) Apron mechanism d) Tumbler gear unit
7. Name the angle marked 'A' in the lathe cutting tool shown in the figure.
a) Front clearance angle b) Side rake angle c) Front rake angle d) Side clearance angle
8. As per Indian Standard System of limits and fits, there are 18 grades of fundamental tolerance.
10. Standard tapers - morse taper. Morse taper is one of the internationally accepted standard tapers.
a) 0 to 7 b) 0 to 8 c) 1 to 7 d) 1 to 8
The other thread element which remains unchanged in both Y and X threads is
12. Thread inspection. Thread ring gauges are used to check external threads. Separate 'Go' and 'No Go' gauging
members are provided. Which one of the following screw thread elements is not checked with the ring gauges?
13. Which one of the following thread forms is mostly found on threaded shafts of lifting equipment for carrying
loads?
c) To ensure a more positive locking d) easy to remove the pin while dismantle
15. The stylus used in mechanical surface measuring machine indentator is made of
a) tool steel b) carbide c) diamond d) cast alloy
16. Heat treatment process. The process of heating steel to about 40 degrees above the upper critical
temperature and cooling it in still air to room temperature is.....
a) Soft and malleable b) Hard and ductile c) Soft and tough d) Hard and brittle
19. various alloying elements are added to improve certain properties of alloy steels.
Which among the following will have the least co-efficient of expression?
20. The most commonly used method of expressing the surface roughness is by the...............
21. The screws used for high duty assembly works. These are normally available
a] Round with taper b] In the form of a circle c] Rectangular d) Square with taper
23. A hole is drilled in a lathe by using 10 mm straight shank drill held in a drill chuck. After a short distance of the
drill
travel, it rotates along with the work. Which one of the following statements is the cause for this defect?
c) Spotting at the centre not done d) Feeding by tail stock hand wheel is too slow.
24. Lead is the metal used for balancing weight during lathe face plate work.
25. 81. Which one of the following thread forms is used on lathe tailstock spindle?