Beruflich Dokumente
Kultur Dokumente
Stevie's 1077W with Simmons 4x32 8-Point Scope, unspecified Silencer and Bipod.
Crosman products Buy Crosman products online Free ground shipping orders > $150 www.pyramydair.com/crosman
Introduction:
This guide is designed to help the beginner and intermediate airgun
enthusiast to be able to completely disassemble the Crosman 1077 and gain a
greater understanding its mechanical workings and components. Note: The
1077, 1077W and 1077AS all disassemble exactly the same way.
Safety:
Never disassemble a gun that is loaded and/or still has Co2 in it.
Be aware of small loaded springs when taking the main housing/receiver
body apart (eye protection is recommended).
References:
The part numbers referenced in this article are from the Crosman 1077 parts
table of Chambers Gun Makers. If you are unclear about any of the parts that
I am describing just look them up here as I will add a part reference number
to disassembly step of the rifle that I describe. Click on the diagram to
expand and be able to view the part numbers. If you would like a complete
parts reference, please see: Here
Required Tools:
1. 4mm Allen key/Hex wrench (Optional).
2. Medium sized Philips screwdriver.
3. Medium sized Flat-head screwdriver.
4. 2mm Allen key/Hex wrench.
http://www.airgunhome.com/pages/1077disassembly.html 10/5/2010
AirGunHome's Crosman 1077 Disassembly Guide Page 2 of 8
5. Snap-ring/Circlip pliers (for valve disassembly only).
All the tools that you will need are pictured on the left.
Preparations:
a) Be sure that you have a large enough workspace before you start disassembly!
b) Make sure you have all the Required Tools listed above or equivalents before you start.
You will need to get any scopes, sights or other add-on parts out of the way if attached. To do this take the 4mm Allen key/Hex wrench (Scopes
usually use 4mm Allen bolts, but not always) loosen the Allen bolts on the scope ring clamps. You will not need to remove the rings. See picture
below:
Now that you have any accessories removed, you will need to remove the stock (#1077-020) from the rifle, To do this you will need to take the
magazine & clip assembly (#1077-005) out of the rifle, then remove the band screw (#1077-042) and the 2 stock screws (#1077-041) located on
the under side of the rifle using the Philips screwdriver. Place the screws in a safe place where they won't get lost. Remember that the larger bolt
type band screw (#1077-042) is from the front most hole. Now you may gently ease the stock away from the rest of the rifle.
http://www.airgunhome.com/pages/1077disassembly.html 10/5/2010
AirGunHome's Crosman 1077 Disassembly Guide Page 3 of 8
Before you start taking out any screws make sure that you take the 12-shot rotary magazine clip (#1077-001) out first. Next, use your Flat-headed
screwdriver to remove the two frame screws (#2-041) on the left hand side and carefully ease the magazine halves (#1077-004, #1077-005) apart.
This is best to do in a clear plastic bag as there is a very small index spring (#106-016) that may fly out. Once it is open and hopefully hasn't
exploded everywhere, remember to take a digital photo of it or memorise it before you take any of the small parts out.
Note: Clip disassembly is not a requirement unless it requires repair.
After removing the stock it will be time to start dismantling the action/receiver housing (#1077-021/#1077-022), This will be one of the more
difficult parts of the disassembly so I will split it up into multiple steps.
http://www.airgunhome.com/pages/1077disassembly.html 10/5/2010
AirGunHome's Crosman 1077 Disassembly Guide Page 4 of 8
Start by turning the housing (#1077-021/#1077-022) over to it's left hand side where there is only one Screw hole near the barrel shroud receiver.
Use a flat-bladed screwdriver to remove the shroud retention screw (#1077-032). Next, flip the rifle over to it's right hand side and again use the
flat-bladed screwdriver to remove all the Screws (#2-041/#1077-032). Don't expect there to a screw in every hole, Crosman has been known to
sometimes leave out one or two. Don't forget to put these screws in a safe place separated from the three stock screws.
http://www.airgunhome.com/pages/1077disassembly.html 10/5/2010
AirGunHome's Crosman 1077 Disassembly Guide Page 5 of 8
Now that you have the housing (#1077-021/#1077-022) open it is a good idea to get the barrel shroud (#1077-010) out of the way. Start by
holding the barrel clamp (#1077-007) and the end of the barrel shroud. Then pull the Barrel shroud away from the barrel (#1077-006) and the rest
of the receiver. To remove the front sight (#766B102) from the barrel shroud use a long (0.5m/18" or longer) dowel and slide it into the barrel
shroud, hold the shroud with the muzzle facing upwards (away from your face) and tap the dowel firmly against the floor and the sight should
come out.
To remove the Co2 tube and/or the valve pipe you will need to remove the Co2
valve (#1077A015) at the same time. Start by lifting the tube (#1077-017) out
from the housing (#1077-021/#1077-022) at the same time as the valve and the
brass valve pipe (#1077-016) place it all down away from the housing. To
separate the valve from the tube gently twist the valve from the pipe and then
http://www.airgunhome.com/pages/1077disassembly.html 10/5/2010
AirGunHome's Crosman 1077 Disassembly Guide Page 6 of 8
the same with the pipe from the Co2 tube.
Lift out the trigger assembly (#1077-033) carefully making sure that the trigger
spring (#1077-014) doesn't fly out if it didn't already when opening the housing in
Step 4B (#1077-021/#1077-022).
Step 8: Removing the Hammer, Hammer Spring and Hammer Pivot Pin
First use the flat-headed screwdriver to unhook the hammer spring (#106035) from the housing (#1077-021/#1077-022). Now take the hammer
pivot pin (#766-044) out from the Hammer (#1077-030) and put it somewhere safe and then lift the hammer out of the housing.
Step 9: Removing the Hammer Latch, Pivot, Latch Spring and Safety
This again is another easily done step, Take the hammer latch (#1077A044) out first being careful not to move the small 'V' shaped spring
(#1077-055), Now take the latch pivot pin (#1077-056) out at the same time as the 'V' shaped spring, Now that this is done just take the safety
slide lever (#1077-040) out by holding the housing (#1077-021/#1077-022) with your hand and pull the safety out straight with your opposing
hand, Simple!
This is one of the more advance steps in this Disassembly Guide. If you are not familiar with valves or not very good with lots of little bits and
pieces I advise you not to do this without direct advice from someone who knows more about the subject.
http://www.airgunhome.com/pages/1077disassembly.html 10/5/2010
AirGunHome's Crosman 1077 Disassembly Guide Page 7 of 8
Now you can have a cup of tea and try and remember why you wanted to take it apart in the first place!
StevieLaner7777
VA Concealed Carry Permit Fun, informative, and easy video class to get your concealed permit! VirginiaGunPermit.com
Nightforce Scopes Premier Dealer Of Nightforce Scope 1 Year 0% Easy Pay 1-800-641-4470 www.BearBasin.Com
Accuracy International Night Force Scopes Aics - Upgrade for Rem 700 milehighshooting.com
http://www.airgunhome.com/pages/1077disassembly.html 10/5/2010
AirGunHome's Crosman 1077 Disassembly Guide Page 8 of 8
Questions or Comments? Click the banner below to go to the discussion forum:
http://www.airgunhome.com/pages/1077disassembly.html 10/5/2010