Beruflich Dokumente
Kultur Dokumente
ISSN 2449-6014
Guide to
telemetry modules
pages 4-51
TELEMETRY MAGAZINE
dedicated to professional GSM/GPRS telemetry and GPS tracking solutions
NOWOŚĆ!!!
in this issue:
NOWOŚĆ!!!
MT-100 – moduł serii profesjonalnej
NOWOŚĆ!!!
MT-101 3G – flagowy moduł telemetryczny MT-101
Sól z Inowrocławskich Kopalni Soli SOLINO S.A. gotowy do pracy w sieciach 3G
MAGAZYN TELEMETRYCZNY MAGAZYN TELEMETRYCZNY MAGAZYN TELEMETRYCZNY MAGAZYN TELEMETRYCZNY MAGAZYN TELEMETRYCZNY
poświęcony profesjonalnym rozwiązaniom telemetrii GPRS i lokalizacji GPS poświęcony profesjonalnym rozwiązaniom telemetrii GPRS i lokalizacji GPS poświęcony profesjonalnym rozwiązaniom telemetrii GPRS i lokalizacji GPS poświęcony profesjonalnym rozwiązaniom telemetrii GPRS i lokalizacji GPS poświęcony profesjonalnym rozwiązaniom telemetrii GPRS i lokalizacji GPS
More information
mable logic controllers (PLC), i.e. support for a local user
• Integrated 2G/3G modem
program (control algorithms, data processing, calcula-
tions). The user program code can be written in one of • Dual-SIM technology
three available editors: text, MTprog conditions sheet • 10 PT1000 inputs, including 2 configurable PT1000 /
and ladder diagram, which are supplied with the free MT 4–20mA inputs
Produktem Roku 2012! Przewodnik po modułach telemetric module configuration parameters are stored in • RS-232/485 serial port for external devices (with galvanic
isolation)
on page 60.
the internal flash memory. It is important for some indus-
trial applications that it is possible to secure the control- • 1-Wire interface
Przewodnik po modułach Przewodnik po modułach The new model MT-156 HMI is a telemetry controller The MT-156 HMI controller comes standard with a modern
In addition to the measurements and control functions,
MT-156 HMI enables data logging by collecting data
records according to a defined configuration in the non-
• Diagnostic LEDs
• Backup battery power input (built-in control and char
char-
telemetrycznych telemetrycznych 3G modem. Dual-SIM technology provides access to two volatile internal memory of the controller. Measurement ging system)
for multichannel temperature measurement desig-
independent GSM networks, providing redundancy of data can be additionally stored on an external SD memory • Programmable PLC
nated for heating, refrigeration, air conditioning
transmission infrastructure. Rich and diverse I/O resources, card. The memory card can also be used to create a backup • Data recorder (1 s time resolution) capable to recording
systems, boiler rooms, server rooms and other facili-
along with available serial interfaces and an Ethernet port, copy of the module’s configuration as well as to locally on the SD card
na stronach 4-47 na stronach 4-47 ties that require monitoring of many PT1000 tempera- ensure the free integration of external devices, sensors update the firmware.
page 60
TECHNOLOGY TECHNOLOGY
DataPortal.online
VirtualMT – programowy symulator
działania urządzeń MT/ML w sieci
Otwarta platforma
strona 56
IoT – new family The platform provides ready-made tools. Users of MT telemetry Devices or data sources
oprogramowania przemysłowego
NOWOŚCI 2013
modules can use the portal for their implementations without the The device added to DataPortal requires a proper network configura-
of sensors need for using other visualization systems. DataPortal is fully compat- tion to correctly communicate with the „Cloud”. A correctly config-
w najnowszych technologiach ible with the project telemetria.pl. It supports all telemetry modules
currently available in the Inventia offer. The service is embedded
ured module is recognized on the base of the transmitted identi-
fier. Data sent to DataPortal is received in an unprocessed form,
page 64 in „Cloud”, where after logging in you have access to management, i.e. we know what the device is sending, but we still do not know
design, and animation of created drawings in RUN mode. You start what final form we will adopt. Data Source is required to interpret
strona 58 the adventure with DataPortal by creating a user profile. received data in DataPortal. It is a complement to a physical device,
an intermediary that provides information to DataPortal, marking
More information
data supply is directly related to the data transmission.
access levels defined in the system and available to administrators
DataPortal.online
MAGAZYN TELEMETRYCZNY MAGAZYN TELEMETRYCZNY MAGAZYN TELEMETRYCZNY MAGAZYN TELEMETRYCZNY a summary of the events that had happened to him.
Nowadays, in the electronic media era, a graphic image
also more quickly speaks to us than text, which carries Own Telemetry Cloud
The primaeval man already knew that the painting on the wall
detailed and additional information. This is confirmed
poświęcony profesjonalnym rozwiązaniom telemetrii GPRS i lokalizacji GPS poświęcony profesjonalnym rozwiązaniom telemetrii GPRS i lokalizacji GPS poświęcony profesjonalnym rozwiązaniom telemetrii GPRS i lokalizacji GPS poświęcony profesjonalnym rozwiązaniom telemetrii GPRS i lokalizacji GPS dedicated to professional GPRS telemetry and GPS localization tracking solutions EDITION by the huge popularity of websites, where users share
photos or videos with each other, and only after that
DataPortal is, to simplify, a SCADA system accessible
from an internet browser. It is a WEB server, displaying
are comments. Similarly, it happens with numbers. The animated visualization in the browser. You log on to the
graph is easier to analyze than a table with many data. Of appropriate page, and animated drawings appear on our
course, it all depends on the type of analysis, and without computer or phone, allowing you to observe the current
JUBILEE a table, there would be no graph. One thing is certain,
imaging the collected data or measurements and the
state of the monitored object or process. You can ask
where is the cutting-edge technology in this? We start the
appropriate presentation makes it much easier to analyze server, we build a data-powered website, and it is ready.
them. The first look at the graphic displayed on the screen This is what the final effect should look like. It should be
INVENTIA Sp. z o.o. was established in 2001 by Our solutions are distinguished by high quality of
spinning off into a new business the experienced products, a 3-year warranty for professional-grade
design and construction department of AB-Micro, devices, innovative functionality, open architecture,
a company operating on the industrial automation scalability and the use of proven industry standards.
market since 1984 as authorized distributor of Barco, User-friendly configuration and integration tools
Eplan, GE FANUC, GE Power Controls, Intellution and provide easy integration of INVENTIA’s products
Hirschmann products. with SCADA-based systems, relational databases,
ASIA
and management systems.
Jamajka
North
– the Polish edition of the magazine the very beginning, gaining a position as a global erate with us in Poland, implementing complex
Maldives
Malaysia
Turkey
Vietnam
confirms Inventia’s position among Pakistan United Arab Emirates
the best companies vendor of telemetry and location equipment within solutions in various branches of industry. We are Qatar
on the Polish market! a few years. INVENTIA’s solutions are developed constantly developing our exports and distribution
by specialists having many years of experience in network outside our country. We are proud that South
automation, telecommunications and IT technology. a Polish product and Polish technological concepts AMERICA
OCEANIA
New Zealand
AFRICA
Benin
Kongo
Mauritius
South Africa
Tunisia
IP67 IP68
e-mail Important properties and functionalities of the devices are indicated by the following pictograms:
GUIDE TO M-BUS
Device with built-in
M-BUS interface
An energy efficient
or energy-saving device
IL
MIM Device with MIM card DIN RA Mounting on DIN rail
TY
Warranty period
W
(Dual SIM) YEARS
• Integral GSM/GPRS 850/900/1800/1900 modem • Universal Timers functionality: Analog/NTC input AN2 – temperature measurement
RAN • Binary inputs and outputs (4/2) – synchronization with internal RTC clock; Sensor type NTC 10 k
AR
• Analog inputs (2) – user-defined counted time range -25 to +55 °C
TY
Measurement range
W
• USB port • Configuration via USB port or from remote using SMS Accuracy ±1 °C (depending on used sensor)
YEARS
• 1-Wire inputs (2) commands
• Dynamic insertion of the variables (e.g. temperature Analog inputs AN1, AN2 – current measurement
• Direct Pt100 and NTC sensors reading
measurement, binary input state) into SMS text messages
• DIN rail mounting Measurement range 4 – 20 mA
MIM • DTMF codes support Maximum input current 50 mA max.
• Configurable via SMS – no PC needed • Possibility of setting limits for SMS transmission Input dynamic impedance 100 Ω typ.
• Build-in SLA battery charger • Internal logger – records the history of device operation; Voltage drop at 20mA 2 V max.
• MIM option available capacity up to 48 000 entries Accuracy ±1,5 % max.
• SMA antenna connector • 12/24V DC accepted power supply
IP67 IP68 Nonlinearity ±1 % max.
• Reach diagnostic LED set (module status, GSM communi-
cation activity, GSM signal strength, binary I/O’s state) Backup battery input ACCU
• User-friendly configuration tools
Nominal battery voltage 6V
• OPC server for Windows
Battery type Lead-acid/gel
Max. charging current 0,4 A (1,3 Ah)
Telemetry module MT-020, thanks to its very attractive cost to Resources General (recommended minimum battery capacity*) 0,8 A (3,0 Ah)
feature ratio, is well suited for use in small sites remote moni- • 4 optoisolated binary inputs Dimensions (length x width x height) 105 x 86 x 58 mm
* Please check battery specification
toring systems. It allows monitoring, diagnosis and control of • 2 potential less outputs with common ground Weight 300 g
• Quad-band GSM/GPRS modem (optionally 3G modem) Power output VOUT1 (stabilized)
remote devices via text messages (SMS and e-mail), CLIP calls Mounting type DIN Rail 35 mm
IP67 IP68
and using data packet transmission of GPRS network. Con- • Dedicated Pt100 input (2- or 3-wire) that can be Operating temperature -20 to +55 °C
Output voltage configurable - 12 V or 20 V
IP65
e-mail
figurable text messages with a fixed or variable content (e.g. configured to operate as voltage (0 – 10 V/0 – 5 V) or Protection class IP40
Max. load current for 20 V 150 mA
current (4 – 20 mA) analog input
containing current measurement value) are convenient way to
• Dedicated NTC sensor input that can be configured Power output VOUT2 (non-stabilized)
provide information to the monitoring center or directly to the GSM/GPRS Modem
to operate as voltage (0 – 10 V/0 – 5 V) or current Output voltage Vpower -2 V
defined staff phone numbers. Alarm messages can be gener- (4 – 20 mA) analog input Modem type µblox LEON G100
Max. load current 50 mA
ated on binary inputs and binary outputs state change, when • A USB port for configuration and diagnostic equipment GSM Quad Band (850/900/1800/1900)
measured analog values crosses alarm threshold, by timer and • Real Time Clock (RTC) - possible external synchronization Class 10
4di/2do counter flags. • Two power outputs (one stabilized) providing power for Antenna 50 Ω Drawings and dimensions (all dimentions in millimeters)
Communication via GPRS enables secure and reliable com- external sensor
GPRS
2ai IP65
munication with higher-order applications (SCADA, database) • SMA antenna connector Power
MODEM Power voltage range DC 9 – 30 V
allowing to expand the capabilities of the monitoring system
Power voltage range AC 12 – 18 Vrms
using remote communication with difficult to access or distant Functionality Current for 12 VDC Idle 0,05 A Max 1,5 A
sites. • Two-way communication via SMS and GPRS Current for 24 VDC Idle 0,03 A Max 1 A
Industrial design, practical I/O resources and easy-to-use soft- • Possibility to send SMS and e-mail messages or GPRS data
ware tools as well as the possibility of remote management of frame on raise of alarm or according to schedule Binary inputs I1 – I4
IP67 IP68
module via SMS commands or GPRS are the biggest advan- • User-defined rules triggering communication (SMS, CLIP
e-mail Signal voltage range 0 – 30 V
tages of MT-020. Direct connection of temperature sensors calls, e-mail, GPRS data frame) on binary inputs, timers
IL
DIN RA
Input resistance 12,7 kΩ
flags, counters flags or registers and internal markers
lowers the cost of building system. 1-Wire inputs can be used Input ON (1) voltage >9V
state change
for reading typical Dallas pellets for the purpose of identifica- Input OFF (0) voltage <3V
• Binary inputs functionality:
tion and authentication. The module can work with humidity Minimum pulse duration 10 ms
– configurable input filtering;
sensors, water level sensors, pressure transducers, flow sen- – possibility of counting pulses in a user-specified range
option
sors, smoke, gas, motion, shock and noise detectors, etc. Outputs Q1 – Q2
(max. 2 147 483 647) and direction (increase/decrease
Output type NPN switch to GND
MT-020 can be powered from a DC voltage source (9-30 VDC) counter value)
Recommended load current for one output 50 mA
or directly from the mains transformer (12-18 Vrms AC). Inte- • Analog values measurement:
GPRS
Max. load current for one output 250 mA
– temperature measurement with Pt100, NTC or 1-Wire
MODEM IP65 grated circuit which controls and charges external battery Resistance in ON state 3 Ω max.
sensors;
MT-020
MT-020
ensures continuous system operation during power failures. Max. load current for both outputs powered from VOUT1 150 mA max.
Dedicated power output allows providing power to external – voltage measurement in 0 – 10 V or 0 – 5 V range;
– current measurement in 4 – 20 mA range;
sensors when operating from backup power source. Analog inputs AN1, AN2 – voltage measurement
– possibility of linear scaling results of the measurements
Optionally module can be produced with 3G modem and/or to engineering units; Measurement range 0 – 5 V/0 – 10 V
with MIM (Machine Identification Module) soldered to PCB Maximum input voltage 18 V
– 4 alarm levels, alarm hysteresis, filtration & deadband
replacing or backing-up standard SIM card. Input dynamic impedance 150 kΩ typ.
parameters defined exclusively for each analog input
Accuracy ± 1,5% max.
• Control outputs functionality:
Nonlinearity ± 1% max.
Typical applications: – bistable, monostable or toggle output with user-
• Alarm systems defined pulse duration time and normal state;
– local control – control output state is changed by Analog/Pt100 input AN1 – temperature measurement
• Access control
• Preventive diagnostic events; Sensor type Pt100, 2- or 3-wired
• Remote meter reading (AMR) – remote control – output state is changed by writing via Wires resistance compensation yes (applies only to 3-wire sensor)
• Remote control of various devices by CLIP call, SMS or SMS/ingoing CLIP call/GPRS data frame value to module Measurement range -40 do +200 °C
• Integral GSM 850/900/1800/1900 modem • SMA antenna connector Analog inputs AN1, AN2 – current measurement
RAN • Binary inputs and outputs (4/4) • Reach diagnostic LED set (module status, GSM communi- Measurement range 4 – 20 mA
AR
• Analog inputs (2)
TY
W
cation activity, GSM signal strength, binary I/O’s state) Maximum input current 50 mA max.
• USB port • User-friendly configuration tools Input dynamic impedance 100 Ω typ.
YEARS
• 1-Wire inputs (2) • OPC server for Windows Voltage drop at 20 mA 2 V max.
• Direct Pt100 and NTC sensors reading Accuracy ±1,5 % max.
• DIN rail mounting General Nonlinearity ±1 % max.
IP67 IP68
• Configurable via SMS – no PC needed Dimensions (length x width x height) 105 x 86 x 58 mm
• E-mail messaging via GPRS Weight 300 g Configuration environment
Mounting type DIN Rail 35 mm
Operating temperature -20 to +55 °C
Protection class IP40
GSM/GPRS Modem
Modem type µblox LEON G100
4di/4do static (text) or dynamic (text and measured values) content • User-defined rules triggering communication (SMS, CLIP
calls, e-mail) on binary inputs, timers flags, counters flags
Current for 12 VDC
Current for 24 VDC
Idle 0,05 A
Idle 0,03 A
Max 2 A
Max 1,5 A
Drawings and dimensions (all dimentions in millimeters)
are a convenient way of passing important information to the
GPRS
2ai IP65monitoring center, or directly to the defined phone numbers.
or registers, and internal markers state change
MODEM • Binary inputs functionality:
SMS and e-mail messages sending can be triggered by change
– configurable input filtering; Binary inputs I1 – I4
of binary input state, reaching alarm thresholds, marker state – possibility of counting pulses in a user-specified range Signal voltage range 0 – 30 V
change, counters and clocks. Industrial design, practical set of (max. 2 147 483 647) and direction (increase/decrease Input resistance 5,4 kΩ
I/O resources, easy to use software tools as well as the ability counter value) Input ON (1) voltage >9 V
to configure the module from remote via SMS commands are • Analog values measurement: Input OFF (0) voltage <3 V
significant advantages of MT-021 in the wireless telemetry – temperature measurement with Pt100, NTC or 1-Wire
IL
DIN RA systems. Direct connection of temperature sensors lowers the sensors;
cost of building system. 1-Wire inputs can be used for reading – voltage measurement in 0 – 10 V or 0 – 5 V range; Outputs Q1 – Q4
typical Dallas pellets for the purpose of identification and – current measurement in 4 – 20 mA range; Output type optoisolated, normally open relay
authentication. The module can work with humidity sensors, – possibility of linear scaling results of the measurements Maximum voltage between contacts 250 VAC/300 VDC
water level sensor, pressure transducers, flow sensors, smoke, to engineering units; Load current 6 A/230 VAC, 6 A/24 VDC
– 4 alarm levels, alarm hysteresis, filtration and Maximum switching current 15 A/20 ms
gas, motion, shock and noise detectors, etc.
deadband parameters defined exclusively for each Resistance <100 mΩ
Typical applications: analog input
• Alarm systems • Control outputs functionality:
• Access control – bistable or monostable output with user-defined pulse Analog/Pt100 input AN1 – temperature measurement
• Preventive diagnostic duration time; Sensor type Pt100, 2- or 3-wired
• Remote meter reading (AMR) – local control – control output state is changed by Wires resistance compensation yes (applies only to 3-wire sensor)
• Remote control of various devices by CLIP call or SMS events; Measurement range –40 to +200 °C
(gates, pumps, heating, lighting, etc.) – remote control – output state is changed by writing via Accuracy ±1 °C
MT-021
MT-021
SMS/ingoing CLIP call value to module’s register
Resources • Universal Timers functionality:
• 4 optoisolated binary inputs – synchronization with internal RTC clock; Analog/NTC input AN2 – temperature measurement
• 4 relay – potential less outputs – user-defined counted time range Sensor type NTC 10 k
• Dedicated Pt100 input (2- or 3-wire) that can be • Configuration via USB port or from remote using SMS Measurement range -25 do +55 °C
configured to operate as voltage (0 – 10 V/0 – 5 V) commands Accuracy ±1 °C (depending on used sensor)
or current (4 – 20 mA) analog input • Dynamic insertion of the variables (e.g. temperature
• Dedicated NTC sensor input that can be configured measurement, binary input state) into SMS text messages
to operate as voltage (0 – 10 V/0 – 5 V) or current • DTMF codes support Analog inputs AN1, AN2 – voltage measurement
(4 – 20 mA) analog input • Possibility of setting limits for SMS transmission
Measurement range 0 – 5 V/0 – 10 V
• Two 1-Wire inputs that can operate also as serial ports • Internal logger – records the history of device operation;
Maximum input voltage 18 V
• A USB port for configuration and diagnostic equipment capacity up to 48 000 entries
Input dynamic impedance 150 kΩ typ.
• Real Time Clock (RTC) with the possibility of external • 9 – 30 V DC accepted power supply
Accuracy ±1,5 % max.
synchronization • DIN rail mounting
Nonlinearity ±1 % max.
• Integral, five band GSM/UMTS modem • Unsolicited message according to event rules and Binary inputs I1 – I6
RAN 800/850/900/1800/1900/2100 (2G/3G) scheduler Input voltage 30 V
AR
• Independent CPU and watchdog system t • Dynamical SMS contents
TY
W
MT-331 Telemetry module (replaced the whole MT-30X series Module is equipped with flash memory reserved for capac-
0-2ai of economical family modules) is a modern unit equipped in ity of 28000 records data logger with maximal resolution of Sensors powering output VOUT
quad band modem uBlox SARA-U201. MT-331 is keeping 1 sec. When actual value of register will be saved with 5 min- Output voltage regulation range 7 – 24 V
aluminum housing and attractive price of economical fam- utes period, the logger can stored measured data of 96 days. Regulation step 0,1 V
ily and offer resources and possibilities that are available in Max. output current 20 mA at 24 V
advanced telemetry devices. Configurable modes of inputs/ 40 mA at 7 – 16 V
With MT-331 module we supplied free of charge applications:
outputs allow to prepare resources for the specific needs of
MT-Manager and MTC for remote and local configuration,
application. Except 2 dedicated binary inputs user can config- Analog inputs 1W, AN1, AN2 Drawings and dimensions (all dimentions in millimeters)
IP67 IP68 resources monitoring and firmware actualization, MT-Data Pro-
ured additional 4 inputs (also as counter mode) and additional
e-mail vider (OPC server, relation data base data saving engine) for Input 1W – temperature measurement
IL 2 binary inputs (instead of analogue). In control applications
DIN RA that required outputs user can configured 4 channels. Measure
communications environment for Microsoft Windows. These Sensor type 1-Wire DS18B20
applications allow easy integration with available on the mar- Measuring range -55 to +125 °C
functions can be realized by 2 configurable analogue inputs,
ket popular SCADA systems. Accuracy ±1 °C
mode 4–20mA or 0–10V. Built-in Li-ion battery keeps power
on in case of lost the main powers supply. Supply output pro- Input AN1, AN2 - voltage measurement
vide a stabilized voltage for external circuits and measurement Similarly to previous MT-30x family the MT-331 is equipped
Measuring range 0 – 10 V
sensors, also in energy saving mode. with stylish aluminum housing with DIN rail connectors.
Max. input voltage 18 V
Though the MT-331 is derived from economical Inventia mod-
Input resistance 207 kΩ typ.
ules series it has got 3 years warranty, like in professional
MT-331 Telemetry module is a green line, energy efficient A/D converter 12 bit
GPRS IP65 module compatible with renewable energy sources. Energy
series, and we are sure it will be useful in many professional
Accuracy ±0,5 %
MODEM applications.
saving mode supported with internal built-in LI-ion battery
Input AN1, AN2 - current measurement
MT-331
MT-331
allows to connect external battery’s as main supply. Device
can be also supply directly from solar panels. In energy Functionality Measuring range 4 – 20 mA
saving mode the module “goes to sleep” (as in batteries family • Transmission modes: Max. input current 50 mA
modules MT-7xx) and wakes up according to configured sched- – GPRS/HSPA – packet transmission Dynamic inputs impedance 120 Ω typ.
ule or occurrence of some events. – SMS Voltage drop for 20mA < 2,4 V max.
• Configurable resources of binary inputs, outputs, counters A/D converter 12 bit
Except standard SIM cards (Subscriber Identification Module) and analogues Accuracy ±0,5 %
the MT-331 used built-in MIM card (Machine Identification • Data logger with 1 second resolution stored data events
Module) which is soldered in packaging mount process of elec- in flash memory (capacity 28000 records) Binary outputs Q1 – Q4
tronics. Depending from preferences user can use: • Remote access to configuration parameters, remote Output type transistor “open drain” type
firmware changing Recommended mean current for a single Output 100 mA
a. Only MIM card, without SIM • Configurable access security – IP and Phone list, optional
Maximum current for a single Output 250 mA
b. Only SIM card, without MIM activation password
• 6 binary inputs can be configured as counters Output Resistance in ON state 3 Ω max.
c. SIM and MIM card (mobile network redundancy).
(up to 100 Hz, without analogue inputs) Maximum voltage applied 24 V
AR
RAN • Integral GSM 850/900/1800/1900 modem Dimensions (H x W x D) in mm:
with autonomic GPRS network logon system MT-051 S (3 alkaline batteries) 75 x 125 x 75
TY
W
MT-051S
• 5 binary/counter inputs with support for potential free MT-051 L (9 alkaline batteries) 175 x 125 x 75
YEARS e n e r g y e ffi
contacts (e.g. pulse outputs of water meters) Weight (with batteries) depends on enclosure size
• Intelligent data logger (max. 28 000 records) and type of battery pack
• Built-in temperature sensor Mounting method 4 holes
MIM • Optional 1-wire port for external temperature sensor Operating temperatures -20°C to +60 °C
MT-051M
• Internal 4.5 VDC alkaline battery pack GSM quad-band (850/900/1800/1900)
(S - 3xLR20, M - 6xLR20 or L - 9xLR20) – support for GPRS Class 10
optional 3 VDC and 3,6 VDC lithium packs Frequency range:
• Intelligent power management Transmitter: 824MHz – 849 MHz
GSM 850 MHz
• USB port for local configuration Receiver: 869 MHz – 894 MHz
Transmitter: 880 MHz – 915 MHz
• IP67 enclosure EGSM 900 MHz
Receiver: 925 MHz – 960 MHz Drawings and dimensions (all dimentions in millimeters)
• Conformal coating for electronics Transmitter: 1710 MHz – 1785 MHz
DCS 1800 MHz
• -20° to +60°C operating temperature Receiver:1805 MHz – 1880 MHz
51S
• Internal GSM antenna or optional SMA connector for Transmitter: 1850 MHz – 1910 MHz MT-0
IP65 PCS 1900 MHz
Receiver:1930 MHz – 1990 MHz
external antenna
Transmitter peak power 33 dBm (2W) – class 4 station
• User friendly configuration tools and communication GSM850/EGSM900
MT-051L
driver (OPC and RDB support)
5di/0do
Transmitter peak power 30 dBm (1W) – class 1 station
• Support for GPRS based remote management and DCS1800/PCS1900
firmware update Antenna 50 Ω
Power
Alkaline battery pack:
S size (height of enclosure: 75mm) 3 alkaline batteries, 4.5 V/16 Ah
M size (height of enclosure: 125mm) 6 alkaline batteries, 4.5 V/32 Ah
51M
MT-0
L size (height of enclosure: 175mm) 9 alkaline batteries, 4.5 V/48 Ah
Mean current consumption with active 20 mA
GSM modem (without GPRS transmission)
MT-051
with data gathering and processing systems. Module has is supplied with user-friendly configuration environment and Minimal pulse length – operating in binary input 2 ms
mode
possibility of initiating data transmission (event-driven or communication driver providing OPC, ODBC and CSV interfaces
scheduled) what helps to minimize the transmission costs and for data acquisition, and the software for remote management
energy consumption, therefore increasing battery life. Robust, via GPRS, including remote configuration and firmware
compact design enclosed in a polycarbonate housing with IP67 upgrade. Logger
protection allows installation and usage of module in places Memory type FLASH
with harsh environment and without power supply (such as Capacity in records 28000
water meter pits). The module is powered from alkaline battery
packs (optional lithium battery packs). Enclosure dimension
indicates nominal capacity of the battery packs (S size - 3xLR20, Additional features
M size - 6xLR20, L size - 9xLR20). Voltage level of power source Dual SIM standard SIM and micro SIM/MIM
is monitored and transmitted together with measurement data. Internal temperature sensor Accuracy: ±1°C @ -25°C do+100 °C
Port for external temperature Accuracy: ±0,5°C @ -10°C do +85 °C
sensor 1-Wire DS18B20 ±2°C @ -55°C do +125 °C
AR
RAN • Integral GSM 850/900/1800/1900 with system for Dimensions (HxWxD) 122 x 120 x 65 (95)* mm Voltage range 0 – 5,0 V
autonomic login to GPRS network
TY
W
integrate with data collecting and processing systems. The configured schedule or on event. Besides measurements the
MT-713 v2
RS-485
spontaneous on event-based or scheduled data transmission module can report multiple alerts: tampering with enclosure,
Analogue inputs AN1 – AN3 (potential, differential)
option helps to minimize energy consumption and transmission unauthorized opening of the chamber, long period of missing
costs extending battery life time. Simple compact design in flow, crossing of predefined level or temperature threshold etc. Measuring range 0 – 5,0 V
plastic enclosure with IP-67 protection makes the module MT-713 module’s resources and functionality may be optimized Input resistance >600 kΩ typ.
ideal for harsh environment with no power lines (eg. water for particular applications due to many available options Resolution 12 bit
GPRS IP65
supply control wells and chambers). Integrated replaceable (3 or 6* lithium or alkaline battery packs, internal antenna, Accuracy ± 0,5 %
MODEM
battery set may endure even for 10 years of operation (lithium opaque cover, communication interface for external devices,
batteries in conjunction with power saving configuration). GPS receiver). User friendly environment for configuration,
communication with open interfaces for OPC/ODBC/CSV and Binary/counter inputs I1 – I5
Battery voltage is continuously monitored and reported remote management comes along with the purchased module, Contact polarization 3V
along with measurement data. MT-713 is equipped with free of charge. The user may fully benefit from new versions
Counting frequency 250 Hz max.
5 binary/counter inputs (adopted to work with potential of firmware thanks to remote firmware upgrade functionality.
Minimum pulse length 2 ms
free contacts) and 3 analogue inputs allowing measuring
of parameters like pressure, temperature, level etc. Keyed * in MT-713 HC with deeper enclosure
voltage source powering analogue inputs for measurement NMOS Q1, Q2 outputs
** option
interval only and binary outputs capable to control power Maximum voltage 30 V
Maximum current 250 mA
Switch off current < 50 µA
Resistance 1Ω
• GSM /GPRS packet transmission and SMS messaging General Configurable voltage output
RAN • Integral GSM 850/900/1800/1900 modem with Dimensions (length x width x height) 80 x 140 x 65 mm Voltage range 0 – 5,0 V
AR
autonomic GPRS network logon system
TY
W
MT-723
Minimal pulse length for counter inputs 2 ms
module. Robust, compact design enclosed in a polycarbonate can also report states of emergency such as mechanical
housing with IP68 protection module allows installation shock, flooding, unauthorized opening of the chamber, lack of Minimal pulse length for binary inputs 0,1 s
and usage of module in places with harsh environment flow, exceeding specified level of flow, pressure, water level,
and without power supply (such as water supply network temperature, humidity, etc. Resources and functionality of the NMOS outputs Q1, Q2
measuring chambers). The module can be powered from MT-723 module can be optimized for specific applications Maximum voltage 30 V
alkaline or lithium battery packs, batteries, solar panels as well thanks to the many available options (module flooding Maximum current 250 mA
as from stationary sources of power. Voltage level of power sensor, pressure transmitter, GPS receiver). The module is
Switch off current < 50 µA
source is constantly monitored and transmitted together with supplied with userfriendly configuration environment and
measurement data. In the case of disconnection of an external communication driver providing OPC, ODBC and CSV interfaces Resistance 1Ω
power supply internal lithium battery provides power essential for data reception and the software for remote management
for counting pulses on inputs I1 – I6, sustains the RTC clock and via GPRS. User can manage modules from remote via GPRS. Logger
triggers power loss alarm. MT-723 module is equipped with 6 Remote management includes firmware updates. Memory type FLASH
Memory size 4 MB (10 000 records)
Minimum recording interval 1s
MT-723 PT logger and transmission module has highest MT-723 PT is equipped with: 6 binary/counter inputs (adapted
IP67 IP68 grade of protection in harsh environment. As other modules to work with potential free contacts for water consumption
Analog inputs AN1 – AN3 (voltage, differential)
of MT family it is known for innovative design, advanced meter), 2 analogue inputs allowing measuring various
technologies and for ease of configuration and integration parameters like pressure, temperature, level, humidity. The Measuring range 0 – 5,0 V
in data collection and processing systems. Spontaneous module has a pressure gauge with quick coupling allowing Input resistance >600 kΩ typ.
data transmission on event occurrence allow minimizing comfortable connection with pressure hose. Extremely low Resolution 12 bits
transmission costs and energy consumption thus prolonging power consumption is achieved by deactivating GPRS/GSM Accuracy in full operating temperature range ± 0,3 %
MT-723 PT
MT-723 PT
battery life time. However it is possible to set up device to modem when not transmitting and using latched power Accuracy in 25°C ± 0,1 %
stay online permanently or for desired time thus allowing to supply output for external analogue sensors or for controlling
IP65
poll both current, logged or both types of data asynchronously power supply to external equipment only for measuring time.
Integrated pressure gauge AN1
from module. Simple, robust design enclosed in polycarbonate Measurement data may be registered with precise time stamp
housing with IP-68 ingress protection class allows installation Measurement range 0 – 10 Bar
in non volatile Flash memory either by schedule or on event.
in harsh environment where there is no supply of electricity Temperature of medium 0 – 80 °C
(like for instance water supply systems measuring chambers). Accuracy 0,5 %
The module can beyond measuring issue alerts in case
of mechanical shock, submersion, unauthorized chamber
The module may be powered from alkaline batteries, lithium opening, lack of flow, too high flow, high pressure, high level, Binary inputs I1 – I6/counter inputs I1 – I5
batteries, lead batteries, solar panels or from power lines. temperature, humidity etc. Contact polarization 3V
Counting frequency for counter inputs 250 Hz max.
The level of power supply is constantly monitored and reported The configuration environment and communication application Minimal pulse length for counter inputs 2 ms
along with measurement data. Internal lithium battery secures with open OPC/ODBC/CSV interfaces and an application for Minimal pulse length for binary inputs 0,1 s
pulse counting on inputs I1–I6 secures RTC clock function and remote management via GPRS network comes free of charge
alarm transmission in case of main supply failure. with the purchase of the module. The user may unrestricted NMOS outputs Q1, Q2
use new firmware versions thanks to capability of remote
Maximum voltage 30 V
upgrading.
Maximum current 250 mA
Switch off current < 50 µA
Resistance 1Ω
• GSM/GPRS packet transmission General Analog inputs AN1, AN2 (4–20 mA)
RAN • Integral GSM 850/900/1800/1900 modem
AR Dimensions (length x width x height) 105 x 86 x 58 mm Measurement range 4 – 20 mA
with automatic login onto GPRS network
TY
W
MT-100
Binary outputs Q1 – Q8
• Simple, multipoint alarm configuration for both binary
Maximum input voltage 36 V
and analog inputs (4 alarm levels)
• Local or remote (via GPRS) configuration and Input resistance 5,4 kΩ tzp.
programming Input voltage ON > 9 V min
• Configurable security access - IP and Phone lists, optional Input voltage OFF < 3 V max.
password
• DIN rail mounting
• 12/24 VDC power supply voltage Outputs Q1 – Q8
• Detachable terminal blocks Recommended average current for single output 50 mA
• Reach diagnostic LEDs (status, GSM transmission activity, Maximum current for single output 350 mA max.
GSM signal level, GPRS activity, I/Os status) Mean current for all outputs 400 mA max.
• User-friendly software tools Voltage drop at 350 mA < 3,5 V max.
• OPC/CSV/ODBC server for Windows operating systems Off state current < 0,2 mA max.
Max. operating voltage 36 V
MT-101
programming Inputs Q1 – Q8
• Configurable access security – IP and Tel. list,
Maximum input voltage 36 V
optional password
• DIN rail mounting Input resistance 5,4 kΩ tzp.
• Power supply 12/24 V DC, 24 V AC Input voltage ON >9 V min
• Removable terminal blocks Input voltage OFF <3 V max
• Diagnostic LED’s (status, GSM transmission activity, GSM
signal level, GPRS activity, serial communication activity,
Outputs Q1 – Q8
I/O status)
Recommended average current for single output 50 mA
Single output current 350 mA max.
Mean current for all outputs 400 mA max.
Voltage drop at 350 mA < 3,5 V max.
Off state current <0,2 mA max.
Max. operating voltage 36 V
MT-102
Mean current for all outputs 400 mA max.
data transmission improvement and event triggering
Voltage drop at 350 mA <3,5 V max.
• Multibroadcast for transparent mode
Off state current <0,2 mA max.
• Remote (via GPRS) configuration and programming
• Configurable access security - IP and Tel. list , optional Max. operating voltage 36 V
password
• DIN rail mounting Analog inputs AN1, AN2 (4 – 20 mA)
• Power supply 12/24V DC, 24 V AC Input current 4 – 20 mA
• Removable terminal blocks Maximum input current 50 mA max.
• Diagnostic LED’s (status, GSM transmission activity, GSM Dynamic input impedance 25 Ω typ.
signal level, GPRS activity, serial communication activity, Voltage drop at 20 mA <5 V max.
I/O status) A/D converter 10 bit
Accuracy ±1,5 % max.
Nonlinearity ±1 % max.
Maximum operating voltage 36 V
• Data and event recording on SD card with 0,1 sec res. Maximum input current 50 mA
2 independent GSM networks ensures superior • Transmission of data from external devices connected
YEARS Dynamic input impedance 55 Ω typ.
availability to RS-232/485 serial port Voltage drop @ 20 mA <5V
• 16 binary inputs (galvanic isolation) • 5 V feeding provided for external device connected to
A/D converter resolution 14 bit
• 12 binary outputs, selectively configurable as inputs RS-232 serial port (e.g. operator panel, GPS receiver)
Accuracy (@ 25 °C) 0,2 %
(galvanic isolation) • Configurable events based on mirrored resources
• 4 analog inputs 4–20 mA (galvanic isolation) of external devices
• 2 analog inputs 0–10 V (w/o galvanic isolation) • Remote configuration and programming via GPRS/HSPA Power supply
• Ethernet port 10Base-T/100Base-TX • SNMP, M-Bus, FlexSerial, IEC 60870-5-104 support
DC (nom. 12/24 V) 10,8 – 30 V
• Configurable access security – list of authorized IPs
PLC • RS-232/485 serial port for external devices (galvanic Input current (@ 24 VDC) Idle Active Max.
isolation) and tel. numbers, optional password 0,06 A 0,25 A 1,00 A
• DIN rail mounting
• RS-232 port with 5 V feeding for operator panels
• Supply voltage 12/24 VDC (24 VDC in case of using
• 48 diagnostic LEDs
connected external battery) Configuration environment
• Battery buffered power supply (SLA battery support) • Built-in management of external SLA backup battery
MIM
IP67 IP68 • Data logger with 0,1 sec resolution (SD card support) • Built-in advanced auto-diagnostics
• Programmable logic controller (PLC) • Detachable terminal blocks
option
• Real Time Clock (RTC)
• Standard communication protocols (MODBUS RTU,
MODBUS TCP, M-BUS, SNMP, IEC 60870-5-104) General
• FlexSerial – programmable handling of Dimensions (L x W x H) 157 x 86 x 58 mm
non-standard serial protocols
Weight 382 g
• Remote configuration, programming, diagnostics
Fixing DIN Rail 35 mm
and firmware upgrade (OTA)
Operating temperature -20 do +65 °C
Operating humidity up to 95% noncondensing
IP65
Protection class IP40
Seria MT-151 LED v2 is a family of new generation teleme- • Interface for backup 12 V SLA battery – charging support GSM/GPRS Modem
try controller for demanding tasks and applications. MT-151 • 2 SIM holders – Dual-SIM support Modem type Cinterion EHS6 Drawings and dimensions (all dimentions in millimeters)
LED v2 model is a professional, industrial design combining • 48 status LEDs (I/O states, successful login to GSM/UMTS GSM 850, 900, 1800, 1900
functionality of programmable logic controller, data logger, network, active GPRS session, signal level, UMTS 800, 850, 900, 1900, 2100
10,5
RX and TX activity of GSM modem, RX and TX activity
MT-151 LED v2
protocol converter and wireless communication interface Antenna 50 Ω
29
16-28di
SIM1
of communication ports, operations on SD card, module
for GPRS packet transmission over GSM network. Dual-SIM
6 1
57
status, primary and backup power source)
/12do technology ensures superior level of GSM network avail-
• Internal flags and registers for user application program
Inputs I1 – I16 * SIM2
ability, with redundant channel of data transmission. Ethernet • Possibility to flash firmware remotely Input voltage range 0 – 30 V
COM2
COM2
I1+ I2+ I3+ I4+ I1 I2 I3 I4 I5 I6 I7 I8 I9 I10 I11 I12 I13 I14 I15 I16
ration tools the MT-151 LED v2 controller is an optimal solution • Transmission models: ETH
111
86
ANTENNA
– SMS
lance and alarm systems.
MT-151
LED
IL Input voltage ON (1) > 9,4 V Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q10 Q11 Q12 Q+ ERR OVR ACCU PWR
MODBUS RTU and MODBUS TCP AI 1-2 PORT 1 BINARY OUTPUTS/INPUTS ACCU POWER
+ +
COM1
GND
GND
COM2
V1+ V2+ D+ RxD TxD Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q10 Q11 Q12
Resources
Q+
RS-232 IP67
• Intelligent packet routing and Multimaster support in
IP68
• 16 optoisolated binary/counter inputs 12/24 VDC Outputs Q1 – Q12
e-mail MODBUS mode
(I1 – I16), positive logic • Programmable control logic using I/Os, timers, Maximum output current 100 mA
157
RS-232/485
• 12 optoisolated binary outputs 12/24 VDC (Q1 – Q12), counters, flags and registers for triggering events Voltage drop @ 100 mA < 0,5 V max.
positive logic – selectively configurable as inputs (data transmission/recording, SMS transmission, e-mail OFF state current < 100 µA
• 4 optoisolated, differential analog inputs 4–20 mA
13
transmission, setting outputs and internal registers,
(accuracy 0,2%, 14-bit resolution @ 1 sec interval)
7
making calls, etc.)
Analog inputs 0 – 10 V (2)
option with configurable hysteresis and filtration • Event based transmission (unsolicited messaging)
• 2 single-ended analog inputs 0–10 V triggered by change of binary input state, internal flag Input voltage range 0 – 10 V
35
46
• Ethernet port 10Base-T/100Base-TX state, by reaching alarm level of analog input, by true Maximum input voltage 20 V SIM 2
SIM 1
MT-151 HMI v2
• Data and Event logger supporting SD card Input voltage range 0 – 30 V
packet transmission over GSM network. Dual-SIM techno-
16-28di logy ensures superior level of GSM network availability, pro-
• RTC with external synchronization functions Input resistance 2,4 mA
/12do viding redundant channel of data transmission. Ethernet Input voltage ON (1) > 9,4 V
port provides powerful capabilities of integration with other Functionality Input voltage OFF (0) < 8,4 V
6ai devices and systems of the user. Graphic display is a conveni- • Transmission models:
– GPRS - packet transmission
ent user interface for local diagnostics, supervision and moni-
toring – without use of external operator panel or portable PC. – SMS Inputs Q1 – Q12 *
• Access to module resources using standard protocols Input voltage range 30 V
With compact, robust design, integral GSM modem, attractive
MODBUS RTU and MODBUS TCP Input resistance 2,4 mA
technical features and easy to use configuration tools the
• Intelligent packet routing and Multimaster support Input voltage ON (1) > 9,4 V
MT-151 HMI v2 controller is an optimal solution for demand- in MODBUS mode
ing wireless telemetry, control, diagnostic, surveillance and Input voltage OFF (0) < 8,4 V
• Programmable control lo/HSPTAgic using I/Os, timers,
IL
DIN RA alarm systems. counters, flags and registers for triggering events
(data transmission/recording, SMS transmission, e-mail
Outputs Q1 – Q12
RS-232 IP67 IP68
Resources transmission, setting outputs and internal registers,
e-mail • 16 optoisolated binary/counter inputs 12/24 VDC making calls, etc.) Maximum output current 100 mA
RS-232/485 (I1 – I16), positive logic • Event based transmission (unsolicited messaging) Voltage drop @ 100 mA < 0,5 V max.
• 12 optoisolated binary outputs 12/24 VDC (Q1 – Q12), triggered by change of binary input state, internal flag OFF state current < 100 µA
positive logic – selectively configurable as inputs state, by reaching alarm level of analog input, by true
• 4 optoisolated differential analog inputs 4 – 20 mA condition.
(accuracy 0,2%, 14-bit resolution @ 1 sec interval) • Configurable SMS messages triggered by alarms and Analog inputs 0 – 10 V (2)
option with configurable hysteresis and filtration scheduled Input voltage range 0 – 10 V
• 2 single-ended analog inputs 0-10 V • Dynamic fields in SMS text Maximum input voltage 20 V
• Ethernet port 10Base-T/100Base-TX • Configurable alarm levels, hysteresis, deadband and Input impedance 197 kΩ typ.
• Isolated RS-232/485 serial port filtration for analog inputs
GPRS IP65 • RS-232 serial port with 5 V / 500 mA feeding • Data and event recording on SD card with 0,1 sec res.
A/D converter resolution 12 bit
MODEM Accuracy (@ 25°C) 0,5 %
• micro USB (AB) port for local configuration and • Transmission of data from external devices connected to
programming RS-232/485 serial port * according to IEC 61131-2 for switch type 1 and 3
• 2G/3G data packet transmission • Transmission of data from external devices connected Analog inputs 4 – 20 mA (2)
AR
RAN • Embedded GSM 2G/3G modem to RS-232/485 serial port and Ethernet port Input current range 4 – 20 mA
TY
MT-156 HMI
channel of data transmission. Ethernet port provides power-
10rtd ful capabilities of integration with other devices and systems
• RTC with external synchronization functions Input voltage OFF (0) < 8,4 V
of the user. Graphic display is a convenient user interface for Functionality
local diagnostics, supervision and monitoring – without use of • Transmission modes:
external operator panel or portable PC. With compact, robust – GPRS/EDGE/3D - packet transmission Outputs Q1 – Q12
design, integral GSM modem, attractive technical eatures and – SMS Maximum output current 100 mA
easy to use configuration tools the MT-156 HMI controller is • Access to the module recources using standard protocols Voltage drop @ 100 mA < 0,5 V
an optimal solution for demanding wireless telemetry, control, MODBUS RTU and MODBUS TCP OFF state current < 10 µA
IL
DIN RA IP67 diagnostic, surveillance and alarm systems.
IP68 • Intelligent packet routing and Multimaster support
e-mail in Modbus mode
RS-232/485
• Data packets broadcast in transparent mode
Resources • Programmable control logic using I/Os, timers, Power Supply
• 12 optoisolated binary outputs 12/24 VDC (Q1 – Q12) - counters, flags and registers for triggering events (data DC (nom. 12/24 V) 10,8 – 30 V
selectively configurable as inputs transmission/recording, SMS transmission, control outputs) Input current (@ 24 VDC) Idle Active Max.
• 2 optoisolated analog inputs 4-20 mA with configurable • Event based transmission (unsolicited messaging) 0,06 A 0,25 A 1,00 A
hysteresis and filtration triggered by change binary input state, internal flag state,
• 2 analog inputs 4-20 mA configurable as RTD inputs by reaching alarm level of analog input, by true condition
for 2 wire PT1000 temperature sensor • Configurable SMS messages triggered by alarms
Analog inputs 4-20mA/PT-1000 (2)
• 8 RTD inputs for 2-wire PT1000 temperature sensor and scheduled
GPRS IP65 • Ethernet port 10Base-T/100Base-TX • Dynamic fields in SMS text Measurement range 4-20 mA/-50 to +150 °C
MODEM
• Isolated RS-232/485 serial port • Configurable alarm levels, hysteresis, deadband Input impedance 47 Ω
M-BUS • RS-232 serial port for external LoRa gateway and filtration for analog inputs A/D converter resolution 20 bit
• 1-wire communication interface • Data recording on SD card with 1 sec resolution Accuracy (@ 25°) 0,2 % /±0,5 °C
Power supply
Voltage range (DC) 12, 24V 10,8 – 36 V
AC (24V) 18 – 26,4 Vrms
Input current (A) Idle Active Max
(for 12V DC) 0,10 0,60 1,90
Drawings and dimensions (all dimentions in millimeters)
Input current (A) Idle Active Max
MT-202 module has been designed for easy, wireless Functionality (for 24V DC) 0,06 0,25 1,00
integration via GPRS network of various remote intelligent • Transmission modes:
devices (e.g. PLC controllers, I/O stations, measuring devices, – GPRS - packet transmission
IP65
operator panels) equipped with serial port RS-232/422/485. – SMS
– CSD - circuit switched data transmission (in modem
mode only) GSM/GPRS Modem
MT-202 can be used as wireless, ”transparent” serial port, but
IL • Access to internal resources with standard MODBUS RTU
DIN RA it can also play a role of a local Master querying periodically
Modem type CINTERION TC63i
protocol GSM QuadBand
an external device for user defined resources (e.g. inputs, • Intelligent packet routing and Multimaster operation in (850/900/1800/1900)
RS-232 outputs, analog inputs, internal registers and flags). In such MODBUS mode Frequency range:
case MT-202 creates in memory a mirror of the external • Packet routing in transparent mode Transmitter: 824 – 849 MHz
RS-232/422/485 resources and detects alarms, state changes, analog value • Wireless serial port capability in transparent mode GSM 850
Receiver: 869 – 894 MHz
changes and fulfilled logic conditions incorporating raw and • Event triggered GPRS transmission (usolicited messaging) Transmitter: 880 – 915 MHz
• Programmable logic functions using markers, timers, EGSM 900
calculated values. Data are transmitted via GPRS according to Receiver: 925 – 960 MHz
user defined rules. counters, diagnostic flags and registers for event Transmitter: 1710 – 1785 MHz
triggering (data transmission, SMS and e-mail sending, DCS 1800
Receiver: 1805 – 1880 MHz
setting values of markers and internal registers) Transmitter: 1850 – 1910 MHz
Industrial grade design, integral GSM/GPRS modem, user PCS 1900
• Unsolicited messages triggered by change of marker state Receiver: 1930 – 1990 MHz
programming capabilities, attractive technical features and or fulfilled logic condition Sender's peak power 33 dBm (2W) -
easy to use configuration tools - these are important advantages • Time-based and event-based SMS messages GSM850/EGSM900 class 4 station
of MT-202 in applications of wireless telemetry, maintenance, • Automatic update of dynamic fields in SMS message Sender's peak power 30 dBm (1W) -
diagnostic, control and automated meter reading (AMR). • Functionality of local Master for slave devices connected DCS1800/PCS1900 class 1 station
to the serial communication port RS-232/422/485 Modulation 0,3 GMSK
• External resources mapping (mirroring) for event detection Channel spacing 200 kHz
Resources and triggering Antenna 50 Ω
• Isolated serial port RS-232/485/422 • Programmable handling of non-standard communication
• User program accessible internal flags and registers: protocols - FlexSerial mode
– 8192 internal 16-bit registers • MT2MT buffer for direct data sharing between MT-202,
– 176 internal flags in binary output space MT-101 and MT-102 telemetry modules.
– 256 internal retentive flags • Built-in data integrity and frame delivery checking
MT-202
MT-202
– 256 internal non-retentive flags • ”Watchdog” circuitry - automatic reset in case of
– 12 independent internal timers abnormal state
– 32 special purpose flags for triggering alarm and event • Timers synchronized with RTC
messages • Local and remote (via GPRS) configuration, programming
• Firmware Flash memory with remote update capability and firmware update
• Real Time Clock (RTC) with external synchronization • Configurable security settings - list of authorized IP
functions addresses and telephone numbers, access passwords
• Power backup detection input • DIN rail mounting
• Power supply 12/24V DC, 24 V AC
• Removable terminal blocks
• Diagnostic LEDs (module status, GSM transmission activity,
GSM signal level, GPRS activity, serial communication
activity)
• User-friendly configuration tools
• GSM/GPRS/EDGE and UMTS/HSDPA packet • Event based transmission (unsolicited messaging) triggered Binary Inputs I1, I2
AR
RAN transmission by change of binary input/output state, internal flag state, Operating in binary input mode:
TY
W
• Integral modem with 6-band UMTS by true condition. Maximum input voltage 55 V
(800/850/900/1700/1900/2100) and quad-band • Remote configuration and programming via 2G/3G Input resistance 11,2 kΩ typ.
YEARS
GPRS/EDGE (850/900/1800/1800) network Input voltage for high state (1) > 9 V min.
• 2 binary inputs, 1 SSR NO output • Configurable access security – list of authorized IPs Input voltage for low state (0) < 3 V max.
• Ethernet port 10Base-T/100Base-TX and telephone numbers, optional password
• 2 serial port to communicate with external • DIN rail mounting Binary output Q1:
devices (expanders): RS-232 with RTS/CTS • 18-55 VDC Power supply Recommended mean current for output 100 mA
handshaking, RS-485 • Built-in management of external SLA backup battery Maximum current for output 1A max.
• Built-in isolated power supply unit • Built-in advanced auto-diagnostics Output resistance in ON state 500 mΩ max.
MT-251
recourses and detects alarms, state changes and fulfilled logic
functionality). Module operates as a SNMP agent – device
conditions incorporating raw and calculated values. Data are Power Supply
which can be polled by server and can send unsolicited
transmitted via 2G/3G network according to user defined rules. information (traps) to server. External resources mapping
Direct Current DC 18 – 55 V
Data may be logged with precise timestamp in non volatile (mirroring) for event detection and triggering
Input current for 24 VDC Idle 0,09 Active 0,25 Max 1,00
Flash memory according to configured schedule or on event. External battery nominal voltage 6V
GPRS IP65
• Data logger recording on microSD card with 0,1 s
resolution
External battery nominal 12 Ah
MODEM capacity
Resources: • Programmable control logic using I/Os, timers, counters, Maximum external battery 100 mA
• 2 binary inputs, 1 SSR NO output flags and register for triggering events (data transmission/ charging current
• Ethernet port 10Base-T/100Base-TX recording, SMS transmission, e-mail transmission, setting
• RS-232 serial port with RTS/CTS handshaking output and internal register, etc.) Ethernet Port
• RS-485 serial port • Configurable SMS messages triggered by alarms and Standard 10Base-T, 100Base-TX
• USB port for local configuration and programming scheduled Connector type RJ45, M12 as option
• Interface for backup 12V SLA battery – charging support • Dynamic Fields in SMS text, support for symbolic names Number of M12 pins 4 pin
• Internal flags and registers for user application program and macros M12 Coding „D”
Power supply
DC voltage 9 – 30 V
Input current (mA) Max Idle Power Save
(for 13,8 V) 200 35 <10
Input current (mA) Max Idle Power Save
GPS (for 27 V) 100 20 <10
GPRS IP65
MODEM
Inputs I1 – I5
ML-231 is a specialized telemetry module dedicated to • Binary inputs signal filtration eliminates signal
Input voltage range 0 – 30 VDC
monitor status and location of vehicles. Module’s design is interference
5di/2do based on latest GPS/GSM technologies securing precision of • Additive or subtractive pulse counting on I3 and I4 inputs Input resistance 22 kΩ
location and GSM signal propagation. The design complies allows variable flow meter connections. Input voltage ON (1) >7V
with automotive industry design standards. • Controlling binary outputs according to internal logic and
2ai
Input voltage OFF (0) < 2,5 V
remote commands Frequency range in counter mode (I3, I4) 50 Hz
Drawings and dimensions (all dimentions in millimeters)
Resources • Detection of missing GPS signal Minimum pulse width “1” 20 ms
• 5 binary inputs including: • Reporting according to defined distance and time criteria
– dedicated ignition ON detection as well as driving direction change
Output 1, 2
– dedicated alarm detection input • Transmission of information as a result of triggering
Recommended average current for single
– 2 general purpose binary inputs predefined event output
250 mA
(with counting and scaling function) • Logging of data in case of missing GSM communication Voltage drop at 250 mA 0,3 V
RS-485 – 1 ground sensitive binary input • Transmission modes
option OFF current 20 µA
• 2 binary outputs – GPRS – packet transmission
Immobilizer, parking mode,
• 2 voltage analogue inputs – SMS Application LED/BUZZER signalling,
– frequency measurement – e-mail others
– average value computing • Configurable transmission in home network and in
– max value detection roaming Input 1-Wire 1, 2
– differential measurement • Dynamic SMS composing allowing transmission of current
Standard Dallas I-Button
ML-231
ML-231
– voltage measuring with alarm thresholds measurements values
driver authorization
– precise fuel level measuring • Configurable SMS limits Application
temperature measurement
• Main supply input with voltage monitoring • Local or remote configuration via GPRS
• Auxiliary supply with voltage monitoring • Configurable access permissions – list of authorized IP
Analogue Inputs
• 2 1-Wire inputs (Dallas iButton) for driver identification addresses and phone numbers
Measurment range 0 – 10 V*
and temperature measuring • Monitoring of main and auxiliary supply voltage
• Diagnostic LED facilitating module’s start Input Resistance 200 kΩ
• Audio input & output (for loudspeaker and microphone)*
• Detachable connector and antenna sockets A / D converter 12 bits
Functionality • Dedicated local connection socket for PC for configuration * with the possibility to increase the scope
* option
IP65 Energy saving location module ML-931 is a specialized tele- • Transmission modes
metry module dedicated to monitor wild animals and other – GPRS – packet transmission
mobile objects. – SMS General Configuration environment
Module’s design is based on latest GPS/GSM technologies • Transmitting information according to time schedule Dimensions (length x width x height) 62 x 40 x 16 mm
GPS securing precise location and reliable operation in changing • Configurable home and roaming transmission parameters
Weight 40 g
GSM propagation conditions. • Dynamic SMS compilation allowing sending current
Gross weight (with silicone) 100 g
The module is manufactured as OEM without dedicated measurement data
• Adjustable SMS transmission limit Mounting method (proprietary) user defined
housing.
• Remote configuration via GPRS/SMS - the module is Operating temperature -20 to +55 °C
preconfigured by manufacturer Protection class none (IP65 optional)
Resources • Configurable access security list for IP addresses and
• 1 binary/supply output phone numbers
• Main supply input with voltage monitoring • Monitoring of power supply voltage GSM/GPRS Modem
• Real Time Clock • Monitoring of internal parameters state Modem type µblox LEON G100
RS-485
option • 30k records logger with option of expanding to 60k • 3-axis accelerometer GSM Quad Band
GSM
– motion detection (850/900/1800/1900)
Functionality – activity detection GPRS class 10
• Cyclical location computing based on received GPS signals • Optional silicone rubber molding to achieve IP65 ingress Antenna built in antenna
• Detection of missing GPS signal protection
• Reporting according to defined criteria of time, motion, • Reed-switch activated storage mode Drawings and dimensions (all dimentions in millimeters)
activity • LED module’s status indicator GPS receiver
• Logging of information when GSM communication is not • RS232 serial port for communication with extension Receiver type µblox NEO-7
available modules* Sensitivity
-162 dBm Super Sense®
Indoor GPS
* option Channel number 50
Antenna built in passive antenna
Power supply
DC voltage 2–5V
Current in active state (mA) 50 mA (average)
ML-931
ML-931
400 mA (max.)
Current in sleep state (µA) < 50 µA (activity control off)
< 200 µA (activity control on)
Serial ports
Standard RS-TTL (2,7 V)
Application external sensors
• Capability of replaying recorded voice announcements Protection class IP40 Inputs I1 – ALARM/I8
IP67 IP68 • Automatic alarm transmission upon activation Input voltage range -30 – 30 V
of ALARM input (SMS/GPRS) Input resistance 5,4 kΩ
• Automatic reception of incoming voice calls, GSM/GPRS Modem Input voltage ON (1) > 9 V or <-9 V
call back function Modem type SIERRA WIRELESS Input voltage OFF (0) -3 – 3 V
• Automatic confirmation of performed voice GSM QuadBand
connections (850/900/1800/1900)
• Optional communication port for monitoring Frequency range: Outputs Q1,Q2
and diagnostics of peripheral equipment Transmitter: 824MHz – 849 MHz Input voltage range 0 – 30 V
GSM 850
(RS-232, RS-485) Receiver: 869 – 894 MHz
Recommended mean current for single output 50 mA
• Support for MicroSD memmory card Transmitter: 880MHz – 915 MHz
EGSM 900 Receiver: 925 – 960 MHz Single output current 350 mA max.
IP65 • Detachable terminals Average current for all outputs 400 mA max.
Transmitter: 1710MHz – 1785 MHz
DCS 1800 Receiver: 1805 – 1880 MHz Voltage drop for 350 mA <3,5 V max.
Transmitter: 1850 – 1910 MHz Current in off state < 0,2 mA max.
PCS 1900 Receiver: 1930 – 1990 MHz
MT-512
as an upgrade during maintenance of existing elevators. • Easy integration with Service Center software
• LED diagnostics (status, GSM activity, GPRS activity,
Resources communication port activity, binary inputs and outputs
• 1 dedicated, opto-isolated alarm input with adjustable state, active voice connection, MicroSD card errors
time of insensitivity for repetitive activations detected) Power Supply
• 7 opto-isolated binary/counter inputs • Detachable terminals
• 2 opto-isolated controlling outputs • Power supply 9 – 30 V DC
• AUDIO output adapted for standard Intercom • DIN rail mounting
• Optional RS-232 or RS-485 serial port for peripheral
equipment (monitoring, diagnostics)
• Flash memory for configuration data, remotely updateable
• Additional external memory (MicroSD card) Light Intercom
• RTC real time clock
LIFT CABINE
• Measurement in the range of microvolts (length x width x height) 190 x 75 x 55 mm USB (Non Isolated, internal)
• GSM/GPRS/EDGE and UMTS/HSDPA packet Wireless (remote) Bluetooth 4.x, BLE*
YEARS IP65 Weight 900 g
transmission Operating temperature -20 to +55 °C
* option
Power supply
Voltage range (DC) 7 – 30 V
Internal battery pack 3 lithium batteries 3xLSH14 (3,6 V)
IP65 10,8 V; 17,4 Ah capacity
Input current (for 24V):
Idle 800 µA
Active 70 mA, 200 mA (charging)
Max 0,7 A
2di/2do
6ai MT-651 telemetry module provides compact and high specifi- • 2 optoisolated groups of analog inputs where each
Inputs IN1, IN2
Input voltage range 0 do+30 V
cation solution for remote monitoring and controlling of pipe- of them contains 2 differential inputs (configurable
Input resistance 60 kΩ typ.
line cathodic protection systems, tanks and other metal structu- measurement range 0–10 V or 0–100 V) and 1 dedicated
res buried in the ground or submerged in water. The flexibility Input voltage ON (1) > 9 V min
input 0–100 mV)
of module configuration allows you to adjust it to a series of Input voltage OFF (0) < 3 V max.
• 2 optoisolated binary outputs (one NC type, second for
installations - from the simplest to the most complex. Internal Minimum pulse length 5 ms
control external bistable relay)
resources of the device allow for easy and secure remote confi- • Execute of measurements in the synchronous mode
guration and implemented data protection mechanisms ensure • Scheduler of measurements and tasks with possibility
safe operation of the system. of modification by user Outputs OUT1, OUT2
• Built-in GPS receiver for time synchronization Voltage switching AC/DC 220 V
il
IP67 IP68
MT-651 module is dedicated to the system where power lines • The accelerometer to detect tampering with the device Single output current 1.5 A
are not available. or the devastation attempts (included unauthorized Maximum switching power 50 W, 100 VA
movement)
IL
DIN RA With MT-651 module we supplied free of charge applications:
• Remote configuration, communication, monitoring and
firmware upgrade via GPRS
MTManager for remote and local configuration, resources Two group of optoisolated input with common ground
• Internal temperature sensor (ANA, ANB)
monitoring and firmware actualization, MT-Data Provider (OPC • Detection of main power failure and battery monitoring
server, relation data base data saving engine) for communica- 0-100 mV input: mVA, mVB
S IP65 • 5 status LEDs (digital I/O states, Power supply status,
M
tions environment for Microsoft Windows. These applications Measurement range ±100 mV
IP67 IP68 GSM status and activity, GPS status) Measurement resolution 1 uV
e-mail allow easy integration with available on the market popular
• Data logger with 0,1 second resolution stored data events Accuracy DC ±0,1 %
RS-485 SCADA systems. Input resistance >1 MΩ
MT-651
in flash memory (capacity 180000 records)
• Possibility to store data on the microSD card 0-100V input: ANA1, ANA2, ANB1, ANB2
• Ability to integrate with SCADA system (OPC DA, OPC UA, Measurement range DC ±10 V; ±100 V
Functionality Measurement range AC 100 V
ODBC and CSV support)
• Mounting in the ø100 mm measurement bollard Accuracy DC ±0,1 %
• Transmission mode: Input resistance >10 MΩ
• Power supply by internal battery pack (external as
– GPRS/HSDPA - packet transmission
optional)
– SMS
• Built-in Quad Band GSM modem
• Configurable access security – IP and Phone list, optional
– 2G (GSM/GPRS EDGE 900/1800)
GPRS IP65 – 3G (UMTS/HSPA+ 900/2100)
password Internal temperature sensor
MODEM • User friendly configuration software Accuracy ±1 °C
• Communication interfaces: USB, RS-485, Bluetooth 4.x*
• Dual-SIM technology – access to 2 independent GSM • Open communication protocol OPEN2
networks ensures superior availability
• 2 binary inputs (one of them operates with pull up to the GPS receiver
ground, one voltage sens.) * option Time synchronization accuracy ±1 ms
• Measurement in the range of microvolts (length x width x height) 190 x 75 x 55 mm USB (Non Isolated, internal)
• GSM/GPRS/EDGE and UMTS/HSDPA packet Bluetooth 4.x, BLE*
YEARS IP65 Weight 900 g Wireless (remote)
transmission Operating temperature -20 to +55 °C
* option
Power supply
Voltage range (DC) 7-30 V
Internal battery backup Li-Ion battery, 2.6 Ah
IP65 Input current (for 24V)
Idle 800 µA
Active 70 mA, 200 mA (charging)
Max 0,7 A
2di/2do
Inputs IN1, IN2
6ai Input voltage range -30 to +30V
Input resistance 5,4 kΩ typ.
Input voltage ON (1) > 9 V min
MT-652 telemetry module provides compact and high specifi- • Dual-SIM technology – access to 2 independent GSM Input voltage OFF (0) < 3 V max.
cation solution for remote monitoring and controlling of pipe- networks ensures superior availability Minimum pulse length 5 ms
line cathodic protection systems, tanks and other metal structu- • Execute of measurements in the synchronous mode
res buried in the ground or submerged in water. The flexibility • Scheduler of measurements and tasks with possibility
of module configuration allows you to adjust it to a series of of modification by user
installations - from the simplest to the most complex. Internal Outputs OUT1, OUT2
• Built-in GPS receiver for time synchronization
resources of the device allow for easy and secure remote confi- • The accelerometer to detect tampering with the device Recommended average current for single output 100 mA
guration and implemented data protection mechanisms ensure or the devastation attempts (included unauthorized Voltage switching AC/DC 60 V max
IP67 IP68
il safe operation of the system. movement) Single output current 1A
• Internal built-in Li-ion battery (2600 mAh) for energy Output resistance in the ON (1) state 0,5 Ω max
With MT-652 module we supplied free of charge applications: backup in the module version powered by DC power
IL
DIN RA MTManager for remote and local configuration, resources supply unit
monitoring and firmware actualization, MT-Data Provider (OPC • Remote configuration, communication, monitoring and Two group of optoisolated input with common ground
firmware upgrade via GPRS (ANA, ANB)
server, relation data base data saving engine) for communica-
• Internal temperature sensor 0-100 mV input: mVA, mVB
S tions environment for Microsoft Windows. These applications
IP65
M
allow easy integration with available on the market popular • Detection of main power failure and battery monitoring Measurement range ±100 mV
IP67 IP68 Measurement resolution 1 uV
e-mail SCADA systems. • 5 status LEDs (digital I/O states, Power supply status, GSM Accuracy DC ±0,1 %
RS-485
status and activity, GPS status) Input resistance >1 MΩ
MT-652
• Data logger with 0,1 second resolution stored data events 0-100 V input: ANA1, ANA2, ANB1, ANB2
Functionality in flash memory (capacity 180000 records) Measurement range DC ±10 V; ±100 V
• DIN 35mm rail mounting • Possibility to store data on the microSD card Measurement range AC 100 V
Measurement resolution 1 mV
• Power supply by external DC unit or internal battery pack • Ability to integrate with SCADA system (OPC DA, OPC UA, Accuracy DC ±0,1 %
• Built-in Quad Band GSM modem ODBC and CSV support) Input resistance >10 MΩ
– 2G (GSM/GPRS EDGE 900/1800) • Transmission mode:
– 3G (UMTS/HSPA+ 900/2100) – GPRS/HSDPA - packet transmission
• Communication interfaces: USB, RS-485, Bluetooth 4.x* – SMS
GPRS IP65 • 2 optoisolated binary inputs (with common ground) • Configurable access security – IP and Phone list, optional
Internal temperature sensor
MODEM Accuracy ±1 °C
• 2 optoisolated groups of analog inputs where each password
of them contains 2 differential inputs (configurable • User friendly configuration software
measurement range 0–10 V or 0–100 V) and 1 dedicated • Open communication protocol OPEN2
input 0–100 mV) GPS receiver
• 2 optoisolated binary outputs (60V, 1A) * option Time synchronization accuracy ±1 ms
• Modubus RTU communication protocols Max. voltage at all connectors relative to 60 Vrms max.
device’s GND.
• Removable terminal blocks
• Easy configuration software
Power Supply
PLC Voltage range (DC) 12,24V 10,8 – 36 V
AC (24V) 18 – 26,4 Vrms
Input current (A) Active
(for 12V DC) 0,20
8-16di Input current (A) Active
• 8 configurable binary outputs / inputs / counters 24 V DC and analog inputs Voltage drop at 350mA <3,5 V max.
Off state current <0,2 mA max.
(Q1 – Q8) • Additional manual alarm level setting capability for
• 2 optoisolated analog inputs 4-20 mA (8 bit acc./10 bit analog inputs A1, A2 (front panel push buttons)
Analog inputs A1, A2 (4 – 20 mA)
res.) with configurable hysteresis and filtration • External, optoisolated RS 232/422/485 serial port Input current 4 – 20 mA
• Isolated serial port RS 232/485/422 for data transmission Maximum input current 50 mA max.
• RTC with external synchronization functions • Configurable access security - password Dynamic input impedance 25 Ω typ.
• DIN rail mounting Voltage drop at 20mA <5 V max.
• Firmware Flash memory with local update capability
A/D converter 10 bit
• Power supply 12/24V DC, 24 V AC
Accuracy ±1,5 % max.
• Removable terminal blocks Nonlinearity ± 1 % max.
• Diagnostic LED’s (status, serial communication activity,
I/O status)
SCADA
• Local logging of measurement results Sample configuration
VPN
• Local execution of user program
• 4 programmatic clocks TMRx – Asynchronous and
EX-101
EX-101
Synchronous
• Can be use like standalone programmable PLC GSM/GPRS
• Main power failure signalization – FS1_UPS
• Support for external text or graphics modbus displays
Access to data
via GPRS router
• Dedicated temperature sensor for MT series • Supports up to 120 M-Bus devices per single bus
RAN telemetry modules • Power on the RS-232 communication port is not
AR
required
TY
W
The system is designed for telemetric modules equipped with Supply current (without output load) 1 mA
Description of the connectors available
pulse inputs operating in the frequency measurement mode, Measurement period 1 min in RM-120 converter module
thus the typical analog inputs are not required for the meas- Battery operating time (3.6 V / 2.5 Ah) 10 years
urement. The sensor housing allows mounting on any flat sur- Connector Description
Operating temperature range -40 to +85 °C
face by means of a double-sided adhesive tape. The module
Protection degree IP40
is designed for indoor and outdoor use, enabling ambient cli- + (MBus) Positive M-Bus terminal
Housing dimensions 71 x71 x 27 mm Technical parameters:
matic conditions monitoring. The device design incorporates
an external source of power or direct power from an optional Rated supply voltage Vz 21,6 – 42 VDC
internal lithium battery (dedicated for use with battery- – (MBus) Negative M-Bus terminal
-powered telemetry modules). Temperature measurement:
Output frequency 0 °C = 10 Hz (5 °C/1 Hz)
Maximum current 1,5 mA
PE2 M-Bus ground consumption by one
Measuring range -40 to 85 °C
Accuracy
M-Bus device
Negative supply terminal
for 25 °C ± 0,5 °C – (24 – 36VDC) Maximum number 120 pcs.
from -10 °C to +85 °C ± 1 °C of the RM-120 module
from -14 °C to +85 °C ± 3 °C
of supported M-Bus devices
Positive supply terminal
RM-120
Drawings and dimensions (all dimentions in millimeters) Resolution 0,1 °C + (24 – 36VDC) RS-232 -> M-bus transmission
of the RM-120 module
THF-01
0 Vz
1 Vz-12V
TXD Output terminal of the RS-232 transmitter
Humidity measurement:
M-Bus -> RS-232 transmission
0 0 – 1,5 mA
Output frequency 50 % = 10 Hz (5 %/1 Hz)
RXD Input terminal of RS-232 receiver 1 11 – 20 mA
Measuring range 1,3 – 100 %
Accuracy ±5 % Operating temperature -20 – 55°C
Resolution 0,1 % COM Common terminal of the RS-232 circuit
Protection degree IP40
Optional signalling of the converter when
Atmospheric pressure measurement: RTS connected to the COM PC port of (unused Dimensions (L x W x H): 35 x 86 x 58 mm
Output frequency 1000 hPa= 1 Hz (50 hPa/1 Hz) when connected to MT module)
Measuring range 513 hPa – 1100 hPa
PE1 Ground of the RS-232 circuit Weight 0,08 kg
Accuracy ± 4 hPa
Resolution 1 hPa
nt
• Wide range of battery capacities from 2,4 Ah to 9Ah cie
YEARS e n e r g y e ffi
• Max. output current 1,5 A
• Can be supplied from a photovoltaic cell
(max. effect due to voltage adjustment)
• Microprocessor controlled charging of battery
• Integrated circuit for battery protection
• 6 diagnostic LED diodes
• Fast DIN rail mounting
IL
DIN RA • IP40 protection class
• 3 year warranty
MT-UPS-1
• Support for photovoltaic cells with max. effect at 16–18 V
voltage
Drawings and dimensions (all dimentions in millimeters)
• Step-up and step-down microprocessor controlled
converter
• Short circuit protection at inputs and outputs
• Parametrising of voltages threshold protects the battery
• Adapted to 12 V SLA batteries with 2,4 Ah to 9 Ah
capacity
• Wide operating temperature range -20 to +55 °C Reverse battery polarity
• Main supply voltage from 21,6 VDC Battery failure
Battery low
Battery charging
Backup power source (battery)
Main power source
The last element of the configuration is the definition of In the message body, you can use UTF-8 encoded charac- For changing the logic state I1 from „1” to „0”
the rule sending the e-mail. It comes down to selecting ters and SNCS commands that allow you to place dynamic
the event configured in the previous step as parameter content and special characters (e.g., a newline character).
settings (Trigger event), indicating the type of message More details on SNCS can be found in the documentation
(Recipient type) as e-mail, indicating the recipient’s of MT-151 LED and MT-151 HMI devices.
address (Recipient address) and the title and content of
the message.
I/O simulators
• supplying the analog input I1 from an external current source; • ground shorting of binary inputs I3, I4, I5, I6, which
• connection to binary outputs Q1 and Q2 buffered with relays, is signaled by lighting green LEDs;
• resistive load up to 250 VAC / 2 A or inductive load up to 125 • shorting to the ground of input I6 by means of a rotary
VAC / 0.5 A; encoder, which enables the delivery of a series of pulses
Also, the module configuration allows for the definition The dynamically developing world of the Internet of pu
publish
assign the address or bit appearing in the memory map, MQTT protocol (Message Queue Telemetry Transport) has
(send)
subscribe (receive)
which is to be accessed through the IEC 104 protocol. been gaining in importance. The specification of MQTT MT-331
end)
/ publish (send)
(s
Each variable may have a unique name, be marked with protocol matches very well to the requirements of broad- p ublish
sub
skr
MT-331
make many manufacturers look favourably on its using in
The communication capabilities of the MT-151 modules The global query is carried out by the command (C_IC_ M2M applications and the Internet of Things. Also, Inven-
working as a Slave device (Server) have been extended by NA_1), which contains an additional parameter determin- tia decided to implement the MQTT protocol for the first
the implementation of IEC 60870-5-104 protocol (abbre- ing whether it is a global question (general) or asking for time in one of its products. MT-331
smartphone
viated as IEC 104). It is a TCP/IP based network protocol a specific group. The module provides eight groups of
widely used in telematic and telemetry systems in power parameters to which individual variables can be assigned. We chose the MT-331 module for this purpose because it
engineering. Polling groups using the global read command requires operates well in IIoT (Industrial Internet of Things) appli-
the appropriate identifier for a particular group 1 – 8. cations. The possibility of adapting the type and number
Implementation of this protocol in the MT-151 module of inputs / outputs to current needs, energy-saving mode
allows handling one TCP / IP client. The module listens The module can also spontaneously send data based on allowing battery supply, energy storage in an internal
on port 2404. The IEC protocol has been adapted based the definitions of an event table. Each of the available 32 lithium battery, the possibility of powering it directly The MQTT protocol is a completely new approach in
on the structure of Modbus registers, which limits the events has its trigger condition and the assigned data to from solar panels, built-in data logger, built-in 2G/3G data transfer. The existing methods have always been
data types to a single bit (single point), a single 16-bit send. They can be single variables or groups. Events can modem and a reliable metal housing are only a few of based on a direct connection between the sender and the
signed register (short scaled) and a variable with a also be sent via the internal program after selecting the the advantages of this model. The ease of integration of recipient, which meant the necessity of multiplying the
floating decimal point written in the dual register P1–P256 flag as the trigger source. IEC events are inde- MT-331 modules with various IT cloud solutions currently transmission if the data were to reach many recipients. In
(short float). We provide a full description of the imple- pendent of the classic events sent by the module. provides support for the MQTT protocol. MQTT, this task is taken over by the broker’s software,
mented functions in the form of an interoperable table. which receives the data published by the source and
already independently handles their sending to recipients
MQTT is a very light and easy-to-use data transmission
subscribing to them, also taking care of their caching until
Addressing IEC variables IEC data type Modbus space Description protocol that does not require a large transmission band-
the subscriber is available. With this approach, creating
(IOA) width and allows you to save energy in battery-powered
a one-to-one or one-to-many networks, is possible with-
5001 – 9801 M_SP_NA_1 IB0 … IB5799 Discrete inputs (IREG bits) devices. The data transfer uses a publication/subscrip-
out any restrictions, also in cases where battery-powered
10001 – 10300 M_ME_NB_1 IR0 … IR299 Input registers tion pattern in which the sender (e.g. sensor or telem-
modules are available only at limited time intervals.
20001 – 36384 M_SP_NA_1 HB0 … HB16383 Outputs (HREG bits) – first 16384 etry module) sends data to the broker acting as a proxy
bits (1024 registers) server, and the recipients communicate with the broker
under the subscription of topics. After receiving a new Accepting the MQTT protocol by users does not mean
40001 – 48192 M_ME_NB_1 HR0 … HR8191 Internal Registers finding a panacea for the standardization problem, as it
message from the sender, the broker informs the involved
clients which previously subscribed to the topic. Each is still not possible to directly connect two devices from
client can be both the sender and the recipient. Thanks different manufacturers. There always has to be broker
By default, over 8,000 registers are available for the IEC The IEC 104 protocol allows to synchronize RTC of client to the standardization, the availability of ready-made on the transaction, and the user decides what and in
104 protocol. They are divided into four blocks form- with server time. By default this functionality is inactive, brokers and client libraries, MQTT protocol support can what form he wants to send and receive, which is de
ing a table of IEC variables. The user can access each but the module configuration allows you to enable time be easily implemented on various platforms. Thanks to facto responsible for correct protocol configuration and
MT-151 register by calling the “read variable” function synchronization over IEC protocol. this, the MT-331 module can be a standard data source data interpretation. However, this does not diminish the
(C_RD_NA_1) with the correct IOA address. The module for systems of various suppliers. The MT-331 module uses advantages of the adopted solution and gives hope for
responds by the value from the corresponding Modbus Transport Layer Security (TLS) encryption to ensure confi- the ever-easier exchange of data between the massively
register/bit. dentiality and integrity of transmitted data. emerging IIoT solutions.
MT-151 HMI V2
Significant changes introduced in the new version:
Q+ and COM2 (+ and - respectively).
• 3G modem replaced the previously used 2G modem The above changes increase the technical capabilities of
– this has improved the responsivity and speed of the MOBICON series and make it easier to use in typi-
packet transmission cal applications. The introduction of a new version for
• The processor has been changed to a version sale does not mean the end of support for the previous
equipped with more RAM and FLASH memory hardware version – new versions of the firmware will be
resources released, with improvements and fixes of errors noticed,
also for the previous version of the hardware.
• The Ethernet port has been moved to the front panel
• LNK and ACT diodes are now integrated with the
The new firmware versions of the MOBICON family
Ethernet port
provide some new features and capabilities. Support
• The USB B port has been replaced by the much more for the standard IEC 60870-5-104 protocol and support
popular micro USB port for the Grundfos GENIbus protocol have been added.
• The small microSD card slot has been replaced with Communication capabilities have been enriched with the
the SD card version – it is much easier to operate ability to send email notifications using the SMTP protocol
a larger SD card in the device. It is also cheaper. (without SSL/TLS). E-mail messages can, just like currently
MT-151 LED V2
Agriculture 4.0, However, there is a chance that this situation will change.
There are technical measures to precisely determine the
climate and soil situation in large areas of crops. This is
recipient – the client will be able to start the adventure with
the system from one sensor and will be able to expand the
system practically without any restrictions, and the data will
be stored in the cloud with easy access from your computer
The basic form of using the AGREUS portal will be acces- AM-110
sed from mobile devices, which will certainly facilitate the
A digital input module that allows the connection of a
use of the system. Data for mobile devices will be down-
pressure switch and a water meter to assess the correct-
loaded from the portal in real time, making the informa-
ness of the irrigation process.
tion available the basis for making decisions. Portal dash-
boards, alarms, and reports received via e-mail or SMS
are additional factors that allow the AGREUS portal to be
AM-411
treated as an irreplaceable source of data about cultiva- The execution module allows independent control of 4
ted crops. valves of the irrigation system activated by 24 VAC.
In addition to access through the cloud, local access will Also the following modules will be available:
also be possible, allowing the dispatching and viewing of
irrigation orders as well as the presentation of the current
and, to a limited extent, historical collected climate para-
AM-200
meters. By default, local access will be less flexible than Temperature and humidity measurement module in
that offered on the portal, which is the result of the limi- greenhouses, cold stores or mushroom cellars, allowing
ted computing resources of the base station. to create a system for monitoring the greenhouse condi-
tions, independent from the control of environmental
parameters.
As the first elements of the AGREUS system, despite the
integrating base station AGB 2000, the modules will be
BASE
Our plans include the creation of many other remote sensors
and execution modules allowing not only for climate
monitoring and irrigation control but also for the physical
protection of equipment and warning against undesirable
phenomena. By definition, the system is prepared for send-
ing data of various types, which is greatly assisted by the
MQTT protocol used for transmission purposes, the emerg-
ing standard of the Internet of Things. The use of MQTT
is not only to ensure the privacy, integrity, and security of
BASE data sent by native elements of the AGREUS System but
also to make possible the products from other manufac-
turers to be integrated with the AGREUS portal using this
protocol. This means opening to unlimited possibilities of
extending the functionality of the AGREUS system, whose
future applications will be limited only by the imagination.
The platform provides ready-made tools. Users of MT telemetry Devices or data sources
modules can use the portal for their implementations without the The device added to DataPortal requires a proper network configura-
need for using other visualization systems. DataPortal is fully compat- tion to correctly communicate with the „Cloud”. A correctly config-
ible with the project telemetria.pl. It supports all telemetry modules ured module is recognized on the base of the transmitted identi-
currently available in the Inventia offer. The service is embedded fier. Data sent to DataPortal is received in an unprocessed form,
in „Cloud”, where after logging in you have access to management, i.e. we know what the device is sending, but we still do not know
design, and animation of created drawings in RUN mode. You start what final form we will adopt. Data Source is required to interpret
the adventure with DataPortal by creating a user profile. received data in DataPortal. It is a complement to a physical device,
an intermediary that provides information to DataPortal, marking
User Profile it with its tag. The data source is created when adding the device
to the „Clouds” resources. The device and data source become
To create a user profile, first of all, a telemetry module is required.
connected. Thanks to such a procedure, the structure of measure-
During the registration of the device, you create your account and the
ment data in DataPortal is separated from the hardware layer. At any
user with the administrative profile. The administrator account has
time, the account Administrator can disconnect the device from the
access to all available functions. It can create additional profiles for
Data Source and use the hardware for other purposes. The source
users who want to access content or contribute to it. New profiles do
still exists and can be powered by data from another device. The
not necessarily have full access to content. We have predicted several
data supply is directly related to the data transmission.
access levels defined in the system and available to administrators
DataPortal.online
„One picture is worth more than 1000 words” – is still the form of animated graphic images that will provide the
an up-to-date Chinese proverb which in the current real- observer expected information in the expected form. We
ity explains how to transfer information to the recipient invite you to read the following thousand words describ-
effectively and simple. The primaeval man already knew ing the details of your own... Telemetry Cloud.
that the painting on the wall of the cave would provide
a summary of the events that had happened to him.
Nowadays, in the electronic media era, a graphic image
also more quickly speaks to us than text, which carries Own Telemetry Cloud
detailed and additional information. This is confirmed
by the huge popularity of websites, where users share DataPortal is, to simplify, a SCADA system accessible
photos or videos with each other, and only after that from an internet browser. It is a WEB server, displaying
are comments. Similarly, it happens with numbers. The animated visualization in the browser. You log on to the
graph is easier to analyze than a table with many data. Of appropriate page, and animated drawings appear on our
course, it all depends on the type of analysis, and without computer or phone, allowing you to observe the current
a table, there would be no graph. One thing is certain, state of the monitored object or process. You can ask
imaging the collected data or measurements and the where is the cutting-edge technology in this? We start the
appropriate presentation makes it much easier to analyze server, we build a data-powered website, and it is ready.
them. The first look at the graphic displayed on the screen This is what the final effect should look like. It should be
immediately characterizes the present or past situation. In finally a tailored visualization on a website that is avail-
the next step, we are interested in details. Such a concept able wherever we have access to the network. We start
of observation occurs in all monitoring or control systems the browser, log in and get the expected screens that to grant rights with one click. Such role is, for example, the Observer Data transmission
of industrial processes. The observer must immediately provide the necessary information after the first look. The profile. It allows only logging into the project or projects with the DataPortal is directly connected to the telemetria.pl project. It is the
get information, e.g. about an alarm event or general next step is a detailed analysis of information and action created visualization indicated by the administrator. The content of easiest and fastest way to communicate in a secure, closed network.
installation status. This task is to be carried out by a against possible irregularities. DataPortal is a place where the account can be expanded by adding additional devices, SIM The „Cloud” itself provides tools for managing your SIM cards.
new internet platform, complementing the telemetria.pl exactly such a tailor-made system can be created. We do cards, and additional services. Administrator permissions allow you Currently, it is possible to assign available cards to your devices. You
project. DataPortal collects data from telemetry modules, not need to buy servers or licenses, install software or to manage the added resources within your account. Only the data can also check the remaining period of card activity and estimated
performs the requested analysis and provides results in develop a program in PHP, JavaScript or HTML. source is missing to receive measurement data from the added devices. data usage. You can choose from three operators who are a partner
of the telemetria.pl project. We have also predicted other methods registers it contains, or maybe it is a plain text. Depending on the type exists temporarily in „Cloud” and is named Block Date.
of providing data that are not yet available in the interface. They chosen, we can specify additional options, e.g. specify scaling condi- The definition comes down to determining what kind
can be included on special request. Meanwhile, when the SIM card tions to process the received values according to a specific pattern. of registers we want to query, with what period. Data-
is already plugged in the device, the logged module transmits data, The alarm settings are also indirectly associated with the TAG type. Portal polls the indicated source with a relevant query
and you have a connection card-device-source in the Cloud, it is DataPortal for indicated TAGs can automatically detect alarm situa- receives a response from the source associated with
time to check if and what data you receive. tions, collect them and display even when a given status no longer the device performs the requested conversions and
exists. Alarms can be presented on dedicated controls described later. provides the resultant value according to the definition
of the TAG. The values are added to the history and
Raw data (RAW) Returning to TAGs, we currently distinguish five types: transmitted as current to the Project related to the TAG.
It is time to choose the resources you want to monitor. Telemetry
REAL – data coming from physical devices are saved in history,
modules send events, contents of the recorder or answer queries. In Projects, Screens
their current value is available on an ongoing basis.
any case, they are numbered registers or bits. DataPortal receives
The project includes Users and Data Sources with TAGs.
data unprocessed by default. Data received from an event or VIRTUAL – unrelated to devices, store data entered from
A project is a set determining the membership of individ-
recorder is presented in decimal or binary format. It is up to the user the visualization level, are saved in history.
ual elements of the visualization system. It also contains,
and first of all, animated screens, which in addition to
graphics have a direct connection to the current and
historical values of specific TAGs. The project combines
all the elements enabling the use of received informa-
tion on animated drawings, diagrams or detailed tables.
The project can be assigned to specific users and thus
becomes available to them. One of the screens in the
project can be selected as a startup. In this way, we get
a user profile, which after logging in starts a properly
prepared screen from which you can navigate through
the entire created visualization.
Creating in DataPortal
Designer
After switching to the DataPortal designing mode, it
launches a tool that allows drawing screens that will
be displayed as animated to the logging users. The
Designer is an editor that allows you to create vector
graphics of different complexity. Also, it is a tool for
reviving them based on data from previously prepared
TAGs. The developer has a workspace for creating
drawings that will become synoptic screens. All basic
options such as save, copy, group, etc. are available
directly from the basic menu. The functions for creating
to decide which values are to be archived and in what form. Some PROCESSED – recalculated data whose value is the result of math-
visualizations are available on dedicated panels, whose
may require rescaling, others may represent a real value only after ematical operations performed, where the arguments
visibility and position on the screen can be controlled
the appropriate „assembly” (e.g., a floating point variable covers a are other Real or Virtual TAGs.
depending on preferences. Once launched, Designer
few registers), others are to be in binary form, and we receive them
LOCAL – unrelated to devices, they store temporary data, presents a system demo screen or an empty workspace,
in decimal form. The data received by DataPortal in the RAW format
derived from the processing of real or virtual TAGs, but only when depending on the choice. We start creating the first or
gives a preview of what the module sends, whether the received
we are looking at drawings; the current value is not archived. next screens in the Project.
data is expected, or perhaps there is too little or too many data.
Having a preview of the raw data, we are close to the values calcu- PLACEHOLDER – indicators for other TAGs, dynamically changed
lated by the specified measurement variable format, i.e. a single when running twin visualizations displaying data from many Drawing Screens
TAG. objects with the same structure in the same figure. We start by determining the size of the drawing and its
proportions in the WORKSPACE panel. At this point, we
The correct interpretation of incoming data from devices is possible also have the option of selecting the UI (user interface)
TAGs and Data blocks only when the TAGs have the correct settings. DataPortal provides style for displaying preset controls (their description
This is what we called a single variable that introduces the current a preview of the current processing results, and when it is neces- is in the following text) and selecting the background
value into the system and is recorded in history. The TAG configura- sary, adjustments and re-verification are possible. TAG values are of the area in the form of any drawing or solid color.
tion allows you to specify its type, i.e. whether the value should be an processed from regular event-sent data from internal device record- Graphic objects and controls are available after invok-
integer with the sign, maybe it is a floating point variable, how many ers as well as from classical time-repeated query. Repeat query ing the TOOLBOX panel. Simple functions such as draw-
ing a line, a circle, a rectangle or any path give you an introduc- control. Such configured Table control is automatically filled in with
tion to creating any graphic. An essential element is also the option data currently displayed in the Graph. The table allows you to export
of inserting text and external graphics. The toolbox also provides your content to a local computer disk with one click. The down-
complex elements, such as an alarm counter, various buttons, and loaded data can be used for further analysis in other programs. The
an animated indicator. After selection, these elements require table also has simple functions for calculating mean values, totals,
adjusting their appearance or operation to match the expectations and differences for displayed data. There is no limit to adding multi-
by modifying their properties available on the panel with the same ple graphs or tables in one project. A specific type of table control
name. The toolbox also provides advanced elements that addition- is Alarm Summary.
ally have their windows with settings available after double-clicking
the added control in the workspace. On the other hand, advanced
elements are nothing but ready-made controls, for example, a chart Alarm handling
which external appearance depends on the chosen UI style. A summary list of alarms is used to display and manage alarms in
the project. The control automatically displays alarms according
to the configuration of the related TAGs. Alarms can be confirmed,
Graphs and Tables deleted and commented with your own text. When creating a screen
A single control can take the form of one of four available graph in the settings of the alarm summary, you can delete or add columns
types: linear, columnar, point (XY) and Gantt. Regardless of the type and auxiliary counters displaying the total number of states in which
selected, the user influences the control’s appearance and its behav- individual alarms are located. The summary also allows you to play
ior by changing the settings on the PROPERTIES panel. For conveni- audio signals when an alarm situation occurs. The complementary
ence, we have divided the settings into groups: General, Axes, Style. element is the alarm counter control. It is foreseen for inserting into
Each of them contains parameters, the change of which allows you drawings, where it is not envisaged to place a table. Thanks to this,
to adjust the control to your own needs. For correct operation, the the user will always be informed about the occurrence of a new
selected type should be equipped with pens that will present values alarm regardless of the currently displayed screen. The alarm coun-
from the indicated TAGs. Each pen can be edited independently. The ter also plays back sound signals.
control displays the current trends in the automatic refresh mode. you to create visualizations of many levels. Among them are also WebMTC
In the properties, you can choose to work with archive data. In ready-made scripts for updating data on demand or for sending
historical mode, the trend display control is done manually by the Let’s show it on the Map control commands to be delivered to remote devices. When design- DataPortal Cloud is not just a visualization. We have also embed-
user. Data presentation is static according to given time criteria. The The MAP control displays in the RUN mode an active map with ing, you can test your visualization at any time by putting it in motion. ded in it the tools designed to change the configuration of connected
change in the approximation is manually triggered, thus completing marked locations of monitored objects. During the configuration of Such an instant preview gives the developer the answer whether the devices. The configuration method and its form were taken from the
the missing measurements. The Graph control is complemented by the control, you can set the initial view of the map, the start posi- expected effect he wants has been achieved. The animated mode MTC program, which we provide in the form of a local, quick config-
a Table that also displays current or historical data for connected tion, and apply and personalize the location markers. The color of is a separate layer of DataPortal. During design, you use it only for urator installed directly on the computer. The network version of
TAGs. The table is independent but can be paired with the Graph the markers is animated and describes the current situation of the testing and diagnostic purposes. webMTC currently embedded in DataPortal allows only the configu-
ration without the possibility of programming (at the moment). In DataPortal is prepared to collect large amounts of frequent measure- within the account is not significant. The number of
the network version, you can modify almost all parameters that are ments. Data acquisition from devices is carried out in RAW mode simultaneous sessions is counted per account (we also
available in the modules, bypassing those responsible for logging and processed form as TAGs. Data can also be registered without enable logging in from many places with the same
the device to the GSM network. the need to build a synoptic. We predicted a few ways of accessing login). We check the number of sessions online and
archives collected by DataPortal. This option is designed specifically display an appropriate message for the user who is
We provide full read and write of configuration, the ability to for the needs of customers who want to take advantages of telem- trying to start the RUN mode above the available limit.
synchronize time, and the access to devices with a password. We etry but accustomed to their systems of visualization or programs.
also support the operation of battery devices that have the function DATA ARCHIVING TIME – the duration of data stor-
of reporting to the MT-Spooler service, which is also implemented Possible forms of data distribution to the customer: age is determined relative to the entire account and
directly in DataPortal. The whole history is also completed by the is counted in days. All TAGs have the same retention
configuration changes history, which was carried out using the DATA REFORWARD (ROUTER LESS) – a service data transfer from period regardless of the frequency of updates. Data
Cloud level. Saved historical configuration images can be described, telemetric devices without the need to use the gateway or access that will go beyond the time limit you have bought is
viewed and, if necessary, loaded into the currently connected device router to telemetry.pl. DataPortal acts as a Router and becomes a deleted. After extending the time limit, new data fill
or used in the future to massive instant updating of multiple devices. telemetry gateway. You only configure data sources and local telem- the increased space to the new threshold. After reduc-
etry system, where you receive data via MT-Data Provider. ing the time limit at the end of the day, the data from
outside the range is marked for deletion. The deletion
Data hosting in DataPortal RARE EXPORT – collected data is available in the form of CSV, XML
of data takes place at the moment of calculating the
daily invoice.
or JSON files according to the set time interval. Data is exported
Maybe we do not need visualization; just Excel is enough or we to the FTP server provided by the user. This method requires TAG
have our data analysis or presentation software? configuration as well because the data in the files are fully processed. TAG VALUE UPDATE – we count daily updates of all
TAGs created per account. The user sees on an ongo-
ing basis how many updates he has and therefore he
OPC UA SERVER – DataPortal becomes an OPC server in UA architec- can see what is the cost is at the moment. We set a
ture. Customers can connect to the server using a secure encrypted daily update limit, and its exceeding will remove addi-
channel. The server provides data according to the configuration of tional parts of the virtual currency from the account
data sources and connected TAGs. at the end of the day. The number of TAG updates is
a dynamic element and each day can be a different
value depending on the device configuration.
Billing
DATAPORTAL
ADDITIONAL SERVICES – at the moment we have
Daily report of using The costs of using DataPortal depend on several factors described three additional services associated with data transfer.
NUMBER OF later in the text. The sum of each factor costs determines the daily Each of them is counted independently and added to
CONNECTED load. In general, we have adopted a daily model for the settle- the final daily cost. Thus, starting next instances of the
DATASOURCES
ment of costs, i.e. once a day the use of resources is reduced OPC server increases the daily cost, such as handling
and the limit of available credit is reduced. The credit is the next FTP server to be connected to the DataPor-
expressed as the amount of virtual currency Vcoin. The tal or the next IP address in the DATA REFORWARD
DAILY resources of Vcoin can be supplemented directly from service.
TAGS’ NUMBER OF
UPDATES SCREENS DataPortal. Depending on the visualization model that
you chose, each project will generate different loads.
Our tests and calculations show that the estimated
DATAPORTAL
The elements affecting the daily invoice include: monthly cost of maintaining one data source, where
BILLING
we have about 9,000 data updates daily, displayed on
three screens with simultaneous access for three users
DATA NUMBER OF SCREENS – we count the number of animated screens
RETENTION is about 3 EUR net.
TIME
ANIMATION created. This is done once a day. The user, while adding
SESSIONS
screens, has a current preview of the current costs that
will be charged to him at the end of the day, so unneces- We invite you to create friendly visualizations and use
sary screens can be deleted and will not be included at the the full possibilities of telemetry in „Cloud” because
end of the day. Data should Work for us!
ADDITIONAL
SERVICES
WEBXway
We are pleased to present the look and some of the WEBXway is transparent and easy to use application
features of the new version of the WEBXway loca- consisting of several functional modules:
tion system that have already been implemented. All • Map – using the OpenStreetMaps maps – with the
service components are manufactured and delivered central map area for showing the track/tracks of
exclusively by Inventia. So far, the basic tool was vehicles and function panels on the left and right As in the previous version, we also provide users with frequently than in the previous version. There will also
side of the screen. The area of the chart its located the ability to manage their objects from the browser. be known navigation panels that were available in the
the XwayMap application designed for monitoring, desktop version. There will also be new panels, so far
at the bottom, giving a unique opportunity to
viewing and analyzing data. Last year, we decided to present on the graph many signals, both analog Completely new graphics are the main changes in the unavailable, e.g. current chart with the possibility of plot-
transfer the application and the system architecture and digital. interface that is visible immediately after logging in. The ting any trend selected from the registered data. New
completely to the internet platform. map is still in a central position and is the most impor- panels will be permanently docked, but it will be possible
• Reports – they are delivered in three formats: XLS, tant element of online monitoring. In the online version, to change their size. Each user will be able to personalize
PDF, and preview. we have decided to use open-source maps, which are the application settings according to personal preferences
• Notifications and User’s events generation – this updated by users from around the world. Thanks to and save them in his own profile.
is another unique solution that allows the user to this approach, we will be able to develop updates more
check the required coincidences between signals
and events generated by telemetry terminals.
• Reading of tachographs and driver cards.
The last two modules are currently being tested by the
development team.
will allow you to modify the properties of your objects and a report archive, where all generated forms will be saved,
resources. However, we are changing the authorization with the option of returning to viewing and re-reading.
system of granting rights to the user. In the new version,
the administrator will be able to assign various privileges
The scheduled report generator will simultaneously work
to users, i.e. to the monitoring function, viewing historical
as a notification module. This is new functionality that is
data, generating reports, managing POI areas, or access-
not available in the XwayMAP application. Notifications
ing the configuration of their devices. The novelty will be
are limited to sending messages to the user with informa-
the rights to individual measurement signals and object-
tion about the occurrence of a significant event, e.g. open-
related events (e.g. refuelling). The administrator will be
ing the cargo space in forbidden place. Notifications will
able to grant or remove another user rights to specific
be sent by post and via SMS. The distribution of messages
signals on selected monitoring objects. Similar rules will
will also be carried out when we are not logged in, and we When developing the project, we benefited from EU
apply to report forms. The administration panel will also
do not monitor the situation on a regular basis. subsidies under the Operation Program OP 2.3.2 Tickets
provide a log that saves changes made by users.
for Innovations for SOHO, project number POIR.02.03.02-
XwaySystem undergoes metamorphosis. Day after day, 14-0014/16-01, “Development and implementation
Also, the Report Engine was written completely from of the GreenWay internet platform with a reading of
we are approaching the launch of the new version. The
the beginning. We designed it specifically for the new tachographs and driver cards and a notification module.“
official date is not yet decided. Work is still underway on
structure of the database, including multithreaded work
the implementation of a part of the functionality. Initially,
and the possibility of replication in the case of expand-
we plan to make the new version available in the fourth
ing computational resources. The new reports will oper-
quarter of 2018. Then all users of the XwayMap program
ate on demand or in schedule mode. Initially, they will
will be able to log in to the new application directly in
only handle time-based orders. In the next stage, we will
their favorite web browser. Soon, we will make the new
add support for object events. The selected report will be
test interface available to interested users. We invite you
generated in the case of a real occurrence of the event, e.g.
to participate in the test program. We are also waiting for
exceeding the speed limit. The completed reports will be
comments or suggestions on what functionalities should
stored in the system and sent via e-mail as an attachment.
offer.
On the Internet platform, we plan to recreate all report
templates that are available in the current version. We
will introduce numerous changes in the form of presenta-
tions on this occasion, but the general idea will remain
unchanged. As before, the reports can be downloaded as
a .pdf and .csv file to a local computer. We will also add
The closing balance of 2017 is a total of over 10,200 modules work- The diagram illustrates how great potential the MT-151 module
ing without failure in Poland and Europe, with application software provides to both the developers of the control system and the user.
developed by CONTROL SYSTEM engineers. In addition to the local visualization, available on the graphic panel
mounted on the face of the control cabinet door, the measurement
In the next thematic blocks, we summarize the most interesting data are additionally transmitted, using the ETHERNET bus, to an
examples of telemetry modules applications. integrated, extended BMS system supervising the full technological
process on this object.
Telemetry Modules
in Control System applications
by Maciej Sawicki
The use of advanced functionality of the advanced implementations launched in 2017, together
new generation telemetry modules MT-151, with our partner companies as well as independently, by
MT-331, MT-713/723 from InVentia in appli- an experienced team of CONTROL SYSTEM engineers. We
cations developed and implemented by the have been consistently focusing on the implementation of
Control System company – edition 02’2018 topics that require expertise knowledge and many years
of experience while remembering that our main goal is
to create final high-quality applications that guarantee
users that they have received the product they expected. Environmental protection – MT-151 LED
In 2017, our team implemented applications based on control module together with EX-101
new generation modules, i.e. MT-151 LED/HMI, MT-251 modules part of the pumping water
3G and MT-331. The increased resources available in the process in a waste incineration plant
MT-151 LED/HMI module combined with the high effi- The application described below uses the
ciency of a modern processor, floating point numbers and multi-processor control structure commonly
the implementation of protocols allowing communica- used in our applications. The MT-151 LED
Introduction tion with external devices through RS-485 and ETHERNET module together with the EX-101 modules
Dear readers of the TELEMETRON magazine, ports, significantly increased functional capabilities. The performs the control process of pumps and
We are giving you another article containing the descrip- MT-251 communication gateway in the 3G version and dampers. Each of the three modules is associ-
tion of the most interesting application solutions imple- the WELOTEC series TK500/700/800 routers enabled the ated with its own application that implements
mented by the CONTROL SYSTEM engineers. Traditionally, trouble-free processing of data streams generated in net- part of the control process. Telemetry modules
this edition is a continuation of publications contained works containing over 150 telemetry modules. In many are connected with each other by RS-485 bus.
in the issues of TELEMETRON magazine from 2008-2017. applications, the MT-331 module was used, which due The electromagnetic flowmeters are also con-
In the latest edition of the article, as in previous years, we to the possibility of working in two power supply modes nected to this communication bus. Above is
would like to present the most interesting and technically turned out to be a very interesting device. shown the communication scheme.
Above is the screenshot of a cloud visualization dedicated For flowmeters dedicated to pressure flows, the appear-
The number of implementations of InVentia telemetry modules in to the TIDALFLUX 2300F flowmeter. In the right part of ance of the application automatically adapts to the type
applications dedicated to billing purposes is growing rapidly. Our the window, there is an additional field informing about of flowmeter.
team of engineers prepared in 2017 a dedicated measurement sys- the level of sensor filling.
tem for gravitational metering of wastewater flow, based on the
professional TIDALFLUX 2300F flowmeter from German company
Krohne, using the latest measurement technologies. The measur-
ing system includes, of course, telemetry set with a cloud applica-
tion for the visualization of the measurement process and a bill-
ing module. Below is a block diagram of a complete, professional
system for gravity metering of wastewater. The system consists of
a measuring chamber with a specialized TIDALFLUX 2300F flow-
meter, a dedicated measuring and telemetric cabinet, containing,
among others, MT-101 telemetry module, and a modern cloud
application for the visualization of the measurement process with
chart modules for calculating balances.
For the needs of our business partners, a new dedicated measuring system was
developed in 2017. It enables the most accurate metering of flows and pressures
in clean water pipelines.
In the picture below an example of a measuring chamber equipped with a classic Below is the visualization of the same object made in
water meter and a pressure sensor is shown. By using the functions offered by a cloud application dedicated to desktop and mobile
the MT-331 module, even in such a simple case, important measurement and devices.
information data are sent to the visualization system, e.g. opening the measur-
ing chamber, exceeding the permissible water level in the chamber, etc.
In this application, the telemetry module is powered from an AGM type battery,
which requires cyclic recharging about three times/year. Thanks to the 2.6 Ah
battery built-in the MT-331 module, it is possible to recharge the external bat-
tery without having to replace it with another battery during charging.
Monitoring of hydrophore sets with own PLC controllers fer data using the ModBus RTU or ModBus TCP protocols. Below is
by the MT-151 telemetry module an example of the visualization of a water treatment station (WTS)
In 2017, the process of incorporating hydrophore sets into the visu- containing three hydrophore sets.
alization systems was continued. In numerous applications, CON- Monitoring of advanced water treatment stations
TROL SYSTEM included objects with various equipment levels in the To make it easier for the new user to “start the adventure” with based on the PROGEA Movicon SCADA system modules were also used in each of the implemented
structures of visualization systems. MT-151 modules have proved telemetry, we offer cloud solutions that allow the implementa- In 2017, our team of engineers implemented extensive applications. The presented example confirms the
their worth in this area of application. Thanks to the availability of tion of visualization without building a standard dispatcher station visualization systems based on the Movicon SCADA extraordinary flexibility in combining, in one system,
RS-485 communication ports, as well as ETHERNET, it was possible equipped with a router. system. In hardware architecture, InVentia telemetry various models of telemetry modules with PLC devices.
in most cases to establish a digital connection with PLCs and trans-
Summary
In 2017, we developed more and more sophisticated applica- Consequently, all new visualization systems have been imple-
tions based on InVentia telemetry modules. Further functions mented based on the Progea Movicon SCADA system, distrib-
added to the firmware of these modules allow our team to uted by AB-MICRO. Last year our engineers gained huge expe-
implement increasingly complex control systems. rience in creating complex applications based on the Movicon
SCADA system. The Movicon.NExT version is another challenge
An interesting direction of the InVentia company activity is the facing our team.
implementation of the MQTT protocol in selected telemetric
modules that allows data exchange with IoT devices.
The track monitoring system has been The infrastructure manager should not only know the
developed in response to the needs of many throughput of his tracks to properly calculate the mainte-
railway infrastructure operators to quickly nance charges, but he must also have a good monitoring
and economically obtain current data for system to optimize maintenance activities and optimally This system provides the necessary sampling frequency and enables
existing electronic surveillance devices use the potential of existing infrastructure. the transfer of results via an internal connector using Modbus. It
without the need to program complex inter- also provides basic signaling of the system operation status and
faces. The Eisenbahntechnik Munder GmbH company based allows you to quickly diagnose possible wrong states contributing
in Berlin (Germany) has developed and patented a track to their quick elimination.
monitoring system that perfectly solves the needs and
problems of customers. The energy-saving MT-713 The first installations of the described track monitoring system
telemetry module manufactured by the INVENTIA was were completed in 2013. Currently, the system works on many
chosen as the basic element of the system. The device railway stations confirming its reliability. The system provides infra-
monitors the railway traffic through two inductive structure managers with valuable traffic information on individual
sensors connected to the track rail and communicates sections of railway tracks.
with the central server. The customer has the option of
accessing data via the web application. At the initial
stage of the concept developing, it was clear that a fully
autonomous system is needed. Both the measurement
section and data communication must operate on their
battery power supply, and the assembly on the rails EISENBAHNTECHNIK MUNDER
GMBH
must be simple and flexible. At the same time, there was
a need for much more cost-effective industrial compo-
nents than those used in traditional solutions.
Mode in practice. See how simple it is”. Archive issues of Additionally, it is possible to send information with
the magazine are available at www.inventia.pl. device status on request. The phone numbers of SMS
messages recipients can be changed using SMS mes-
In its current form, the internal program in the MT-101 sages sent from authorized phone numbers. If necessary,
controller is prepared to download parameters from you can also remotely suspend the handling of text mes-
up to 6 external devices. With a one-minute interval, sages.
the MT-101 controller builds and sends an initializa-
tion frame, which forces data transmission by a slave Our experience shows that the solutions offered by
type device. The received response is analyzed regard- INVENTIA are of high quality. We are sure that the
ing sender’s ID. The variables to be calculated include appropriate components were selected when design-
Control
belt conveyor run time, number of engine starts, time of ing telemetry modules, thus obtaining high product
material presence on the belt and the total amount of strength in harsh environmental conditions. The confir-
raw material produced. mation of this thesis is our installations, where telemetric
of production processes
MultiBand
by Michael Kenny
Multiband Antennas company (Dublin, Ire- Telemetry modules monitor various types of produc-
land), for several years, has been success- tion processes and industrial devices, such as crushers,
fully implementing wireless telemetry sys- conveyor belts, scales or other machines used in gravel
tems based on leading constructions offered and quarry areas located throughout Europe. Production
by INVENTIA, such as the modules of the pro- data is collected in real time and analyzed by internal
fessional series: MT-101 and MT-100. user algorithms which are built based on the internal
program of MT-101 and MT-100 controllers. Pre-pro- In those installations where peripheral devices have no modules often exposed to large temperature differences,
cessed data is transmitted using the GSM/GPRS network serial interfaces, the MT-100 telemetry module is used. mechanical and electrical exposures work without fail-
based on the SIM card with dynamic IP address to the A large number of binary inputs, which can be config- ure for years, ensuring comfort and satisfaction to our
server of the MT device manufacturer. The next step is ured to work as counter inputs, are sufficient to obtain customers.
downloading data from the server using the FTP proto- data and to internally calculate the variables of the pro-
col and their presentation on the website, in a dedicated duction process that have been mentioned above.
system called MultiTrack.
Moreover, the telemetry modules in addition to the
The MT-101 telemetry controller is used in more demand- production parameters monitor their process variables,
ing installations, where integration with external devices among which are: the back-up battery voltage level, the
is desired using a serial interface and a program han- presence of the main power supply voltage or the login
dling of serial port built in the MT module – the FlexSerial status to the GSM/GPRS network. In the event of an
mode. The practical application of this mode is described alarm situation, SMS messages are sent to the defined
in the second edition of the Telemetron magazine. We telephone numbers of service of the given facility.
encourage you to read an article of the title “FlexSerial
MODULE
MODULE
MT-020 MT-021 MT-051 MT-100 MT-101 MT-102 MT-151 LED v2 MT-151 HMI v2 MT-156 HMI MT-202 MT-251 MT-331 MT-512 MT-651
Telemetry Telemetry Telemetry Telemetry Telemetry Telemetry Telemetry Telemetry Telemetry Telemetry Telemetry Telemetry Telemetry Telemetry
Module Module Module Module Module Module Module Module Module Module Module Module Module Module
FEATURES FEATURES
I/O Resources I/O Resources
Binary inputs 0 – 41) 0 – 41) 5 8 – 161) 8 – 161) 0 – 81) 16 – 281) Binary inputs 16 – 28
1)
0 – 121) – 0–2 0 – 81) 8 2
222)
1) 1) 1) 1) 1) 1)
Binary outputs 2 4 - 0–8 0–8 0–8 0 – 12 Binary outputs 0 – 12 0 – 12 – 1 0 – 41) 2
1,4)
Counter inputs 0–4 0 – 41,4) 5 8 – 161,2) 8 – 161,2) 0 – 81,2) 0 – 41) Counter inputs 0–4
1)
– – – 0 – 61) 8 –
623)
1)
Analog inputs 2 2 – 2 2 6 6 Analog inputs 6 10 – – 0–2 –
8)
1-wire input 2 2 1 – – – – 1-wire input – 1 – – 1 – –
Real Time Clock (RTC) YES YES YES YES YES YES YES Real Time Clock (RTC) YES YES YES YES YES YES YES
Ethernet Port – – – – – – YES Ethernet Port YES YES – YES – – –
8) 8) 25) 8)
Serial port RS232/422/485 – – – 1(1/0/0/0) 2(2/1/1/0) 2(2/1/1/0) 2(1/0/1/1) Serial port RS232/422/485 2(1/0/1/1) 3(2/0/1/0/1 ) 2(2/1/1/0) 2(1/0/1/0) – 1(1/0/1 /0) 1(0/0/1/0)
Voice channel – – – – – – – Voice channel – – – – – YES –
Functionality Functionality
Local configuration via RS232/USB/ETH –/+/– –/+/– –/+/– +/–/– +/–/– +/–/– –/+/+ Local configuration via RS232/USB/ETH –/+/+ –/+/+ +/–/– –/+/+ –/+/– –/+/– –/+/–
9)
Remote configuration over GPRS YES YES YES YES YES YES YES Remote configuration over GPRS YES YES YES YES YES YES YES
Unsolicited messaging YES YES YES YES YES YES YES Unsolicited messaging YES YES YES YES YES YES YES
10)
Data packet sending YES YES YES YES YES YES YES Data packet sending YES YES YES YES YES YES YES
SMS sending YES YES YES YES YES YES YES SMS sending YES YES YES YES YES YES YES
User programming (lines of code limit) – – – 100 1024 1024 5000 User programming (lines of code limit) 5000 5000 1024 5000 – – –
YES5)
5) 5) 5) 5) 5) 5) 5) 8)
Standard serial protocols – – – – YES YES YES Standard serial protocols YES YES YES YES – YES
Data packet routing – – – – YES YES YES Data packet routing YES YES YES YES – – –
7)
Manual alarm setting for analog inputs – – – – YES YES – Manual alarm setting for analog inputs – – – – – – YES
Number of analog input alarm levels 4 4 4 4 6 4/6 4 Number of analog input alarm levels 4 4 – – 4 – 6
16) 16)
Remote read/write with SMS YES YES YES YES YES YES YES Remote read/write with SMS YES YES YES YES YES YES YES
Access control6) YES YES YES YES YES YES YES Access control6) YES YES YES YES YES YES YES
Local mirroring of external resources – – – – YES YES YES Local mirroring of external resources YES YES YES YES – YES –
18)
Datalogger YES YES18) YES YES YES YES YES Datalogger YES YES YES YES YES YES
8)
YES
10)
MT-DP compatibility (OPC, CSV, ODBC) YES YES YES YES YES YES YES MT-DP compatibility (OPC, CSV, ODBC) YES YES YES YES YES YES YES
10)
Remote firmware upgrade over GPRS YES YES YES YES YES YES YES Remote firmware upgrade over GPRS YES YES YES YES YES YES YES
Other Other
Integral GSM/GPRS modem YES YES YES YES YES YES YES Integral GSM/GPRS modem YES YES YES YES YES YES YES
SIM/µSIM/
SIM cards SIM/MIM8) SIM SIM SIM SIM 2xSIM/MIM8) SIM cards 2xSIM/MIM8) 2xSIM/MIM8) SIM SIM/MIM8) SIM/MIM8) SIM 2xSIM
MIM8)
8) 8) 8) 8) 8)
3G network support YES – – – – – YES 3G network support YES YES – YES YES – YES
Integral GPS receiver – – – – – – – Integral GPS receiver – – – – – – YES
Integrated sensor T/H/P P8) – T – – – T Integrated sensor T/H/P T T – – T/H8)/P8) – T
DC power supply (V)/solar panel (PV) 9 – 30 9 – 30 – 9 – 30 10,8 – 36 10,8 – 36 10,8 – 30 DC power supply (V)/solar panel (PV) 10,8 – 30 10,8 – 30 10,8 – 36 18 – 55 9 – 30/PV 9 – 30 7 – 30
AC power supply (Vrms) 12 – 18 – – – 18 – 26,4 18 – 26,4 – AC power supply (Vrms) – – 18 – 26,4 – – – –
Power supply for external sensors (V) 12/20 – – – – – – Power supply for external sensors (V) – – – – 7 – 24 – –
Power supply monitoring input YES/– YES/– YES/– YES/– YES/– YES/– YES/– Power supply monitoring input YES/– YES/– YES/– YES/– YES/– YES/– –
Rechargeable battery int./ext. ext. – – – – – ext. Rechargeable battery int./ext. ext. ext. – ext. int. – –
Internal battery supply – – 3/6/9xR20 – – – – Internal battery supply – – – – – – YES
Low power operation modes – – YES – – – – Low power operation modes – – – – YES – YES
External antenna connector YES YES YES YES YES YES YES External antenna connector YES YES YES YES YES YES YES
Protection class IP40 IP40 IP67 IP40 IP40 IP40 IP40 Protection class IP40 IP40 IP40 IP40 IP40 IP40 IP65
Operating temperature range (°C) -20...+55 -20...+55 -20...+60 -20...+65 -20...+65 -20...+65 -20...+65 Operating temperature range (°C) -20...+65 -20...+65 -20...+65 -20...+60 0...+5519) -20...+55 -20...+55
Removable terminal blocks YES YES YES YES YES YES YES Removable terminal blocks YES YES YES YES YES YES YES
8)
DIN rail mounting YES YES – YES YES YES YES DIN rail mounting YES YES YES YES YES YES YES
17)
Warranty 3 years 3 years 3 years 3 years 3 years 3 years 3 years Warranty 3 years 3 years 3 years 3 years 3 years 3 years 3 years
Built-in device – – – – – – – Built-in device display display – – – – –
1) number of binary inputs/outputs and counter inputs 5) Modbus RTU Master/Slave, transparent mode, other… 9) requires MTSpooler 14) one dedicated input for pressure measurement 18) device status recorder 22) Output 1 for control external bistable relay
is configurable 6) password + internal list of authorized IP 10) in new version since Q3 2012 15) voltage measurement, peak detector, differential 19) or -20...+55°C - depending on the version of the 23) 2 optoisolated groups of analog inputs: 2x10/100 V
2) fmax = 100Hz and telephone numbers 11) if connected to MT-101/102/202 measurement internal battery and 200 mV input with 1 µV resolution
3) fmax = 250Hz 7) for 2 inputs 12) RS-232 to M-Bus converter 16) module is not receiving SMS asleep 20) Li-Ion 24) dedicated cable needed
4) fmax = 1kHz 8) option 13) external battery pack required 17) battery 1 year 21) GSM i GPS 25) M-BUS
MODULE
MODULE
MT-652 MT-713 v.2 MT-723 MT-723 PT ML-231 ML-931 EX-101 RM-120 MT-UPS-1 IOT-RT-01 IOT-RTH-01 IOT-RG-01 IOT-RG-02 IOT-TST-01
Telemetry Telemetry Telemetry Telemetry Location Location Expander RS232/M-Bus Telemetry IOT Sensor IOT Sensor IOT Gateway IOT Gateway IOT Tester
Module Module Module Module Module Module Converter Module
FEATURES FEATURES
I/O Resources I/O Resources
1)
Binary inputs 2 5 6 6 5 – 8 – 16 Binary inputs – – – – – – –
1)
Binary outputs 2 2 2 2 2 1 0–8 Binary outputs – – – – – – –
3)
Counter inputs – 5 53) 53) 21,2) – 8 – 161,2) Counter inputs – – – – – – –
23) 14) 15)
Analog inputs 6 3 3 3 2 – 2 Analog inputs – – – – – – –
1-wire input – – – – YES – – 1-wire input – – – – – – –
Real Time Clock (RTC) YES YES YES YES YES YES – Real Time Clock (RTC) – – YES YES – – YES
Ethernet Port – – – – – – – Ethernet Port – – – – – – –
8) 8) 12)
Serial port RS232/422/485 1(0/0/1/0) 1(0/0/1/0) – – 1(0/0/0/1) 1(0/0/0/1) 2(2/1/1/0) Serial port RS232/422/485 1 – – – 1(1/0/0/0) 1(0/0/1/0) –
Voice channel – – – – YES8) – – Voice channel – – – – – – –
Functionality Functionality
24)
Local configuration via RS232/USB/ETH –/+/– –/+/– –/+/– –/+/– –/+ /– –/–/– +/–/– Local configuration via RS232/USB/ETH –/–/– –/–/– –/–/– –/–/– –/–/– –/–/– –/–/–
9) 9) 9) 9)
Remote configuration over GPRS YES YES YES YES YES YES – Remote configuration over GPRS – – – – – – –
Unsolicited messaging YES YES YES YES YES YES YES Unsolicited messaging – – – – – – –
Data packet sending YES YES YES YES YES YES YES Data packet sending – – – – – – –
SMS sending YES YES YES YES YES YES – SMS sending – – – – – – –
User programming (lines of code limit) – – – – – – 1000 User programming (lines of code limit) – – – – – – –
5) 8) 8) 11)
Standard serial protocols YES YES – – YES YES YES Standard serial protocols – – – – – – –
Data packet routing – – – – – – – Data packet routing – – – – – – –
Manual alarm setting for analog inputs YES – – – – – YES Manual alarm setting for analog inputs – – – – – – –
Number of analog input alarm levels 6 4 4 4 4 – 6 Number of analog input alarm levels – – – – – – –
16) 16) 16) 16)
Remote read/write with SMS YES YES YES YES YES YES – Remote read/write with SMS – – – – – – –
Access control
6)
YES YES YES YES YES YES YES Access control6) – – – – – – –
Local mirroring of external resources – YES – – – – – Local mirroring of external resources – – – – – – –
Datalogger YES YES YES YES YES YES YES Datalogger – – – – – – –
MT-DP compatibility (OPC, CSV, ODBC) YES YES YES YES YES YES YES MT-DP compatibility (OPC, CSV, ODBC) – – – – – – –
Remote firmware upgrade over GPRS YES YES YES YES YES YES – Remote firmware upgrade over GPRS – – – – – – –
Other Other
Integral GSM/GPRS modem YES YES YES YES YES YES – Integral GSM/GPRS modem – – – – – – –
SIM cards 2xSIM SIM/MIM8) SIM SIM SIM/MIM8) SIM – SIM cards – – – – – – –
1) number of binary inputs/outputs and counter inputs 5) Modbus RTU Master/Slave, transparent mode, other… 9) requires MTSpooler 14) one dedicated input for pressure measurement 18) device status recorder 22) Output 1 for control external bistable relay
is configurable 6) password + internal list of authorized IP 10) in new version since Q3 2012 15) voltage measurement, peak detector, differential 19) or -20...+55°C - depending on the version of the 23) 2 optoisolated groups of analog inputs: 2x10/100 V
2) fmax = 100Hz and telephone numbers 11) if connected to MT-101/102/202 measurement internal battery and 200 mV input with 1 µV resolution
3) fmax = 250Hz 7) for 2 inputs 12) RS-232 to M-Bus converter 16) module is not receiving SMS asleep 20) Li-Ion 24) dedicated cable needed
4) fmax = 1kHz 8) option 13) external battery pack required 17) battery 1 year 21) GSM i GPS 25) M-BUS
MT-151 HMI
I/O PLC with remote
3G/GPRS access
MT-051
Remote reading
of Water Meters
e-mail MT-102 local Master
for measure devices
GSM/GPRS/3G
MT-331 Data monitoring
Datalogger and control
MT-02X GPRS/SMS/email with alarm
event transmission notification
Private GPRS
LAN/WAN/
Battery datalogger
Internet network
MT-331 MT-713
remote reading
InVentia – Professional Telemetry
Xway/ML-231
vehicle
tracking
MT-723 Battery datalogger
TK7xx/8xx – GPRS/3G/LTE
Over 90 000 modules installed in 57 countries of the world