Beruflich Dokumente
Kultur Dokumente
CLP-600 Series
CLP-600/CLP-600N
Basic Model : CLP-600
Manual
SERVICE
Samsung Color Laser Printer The keynote of Product
- Speed: A4, 20/20ppm(Color/Mono)
1200dpi x 1200dpi
- Emulation: SPL-C(GDI)
1. Precautions
2. Product Specification
3. System Overview
7. Troubleshooting
9. Block diagram
1
1. Precautions
In order to prevent accidents and to prevent damage to the equipment please read the precautions listed
below carefully before servicing the printer and follow them closely.
Warning >> Never operate or service the printer with the protective cover removed from Laser/Scanner assembly. The
reflected beam, although invisible, can damage your eyes. When using this product, these basic safety
pre-cautions should always be followed to reduce risk of fire, electric shock, and injury to persons.
Service Manual
1-1
Samsung Electronics
Precautions
This product contains toxic materials that could cause illness if ingested.
(1) If the LCD control panel is damaged it is possible for the liquid inside to leak. This liquid is toxic. Contact with the skin
should be avoided, wash any splashes from eyes or skin immediately and contact your doctor. If the liquid gets into
the mouth or is swallowed see a doctor immediately.
(2) Please keep toner cartridges away from children. The toner powder contained in the toner cartridge may be harmful
and if swallowed you should contact a doctor.
Failure to follow the following instructions could cause electric shock or potentially cause a fire.
(1) Use only the correct voltage, failure to do so could damage the printer and potentially cause a fire or electric
shock.
(2) Use only the power cable supplied with the printer. Use of an incorrectly specified cable could cause the cable
to overheat and potentially cause a fire.
(3) Do not overload the power socket, this could lead to overheating of the cables inside the wall and could lead to
a fire.
(4) Do not allow water or other liquids to spill into the printer, this can cause electric shock. Do not allow paper
clips, pins or other foreign objects to fall into the printer these could cause a short circuit leading to an electric
shock or fire hazard..
(5) Never touch the plugs on either end of the power cable with wet hands, this can cause electric shock. When
servicing the printer remove the power plug from the wall socket.
(6) Use caution when inserting or removing the power connector. The power connector must be inserted com-
pletely otherwise a poor contact could cause overheating possibly leading to a fire. When removing the power
connector grip it firmly and pull.
(7) Take care of the power cable. Do not allow it to become twisted, bent sharply round corners or otherwise
damaged. Do not place objects on top of the power cable. If the power cable is damaged it could overheat and
cause a fire or exposed cables could cause an electric shock. Replace a damaged power cable immediately,
do not reuse or repair the damaged cable. Some chemicals can attack the coating on the power cable,
weakening the cover or exposing cables causing fire and shock risks.
(8) Ensure that the power sockets and plugs are not cracked or broken in any way. Any such defects should be
repaired immediately. Take care not to cut or damage the power cable or plugs when moving the machine.
(9) Use caution during thunder or lightening storms. Samsung recommend that this machine be disconnected from
the power source when such weather conditions are expected. Do not touch the machine or the power cord if it
is still connected to the wall socket in these weather conditions.
(10) Avoid damp or dusty areas, install the printer in a clean well ventilated location. Do not position the machine
near a humidifier. Damp and dust build up inside the machine can lead to overheating and cause a fire.
(11) Do not position the printer in direct sunlight. This will cause the temperature inside the printer to rise possibly
leading to the printer failing to work properly and in extreme conditions could lead to a fire.
(12) Do not insert any metal objects into the machine through the ventilator fan or other part of the casing, it could
make contact with a high voltage conductor inside the machine and cause an electric shock.
Service Manual
1-2
Samsung Electronics
Precautions
The following instructions are for your own personal safety, to avoid injury and so as not to damage the printer
(1) Ensure the printer is installed on a level surface, capable of supporting its weight. Failure to do so could cause
the printer to tip or fall.
(2) The printer contains many rollers, gears and fans. Take great care to ensure that you do not catch your fingers,
hair or clothing in any of these rotating devices.
(3) Do not place any small metal objects, containers of water, chemicals or other liquids close to the printer which if
spilled could get into the machine and cause damage or a shock or fire hazard.
(4) Do not install the machine in areas with high dust or moisture levels, beside on open window or close to a
humidifier or heater. Damage could be caused to the printer in such areas.
(5) Do not place candles, burning cigarettes, etc. on the printer, these could cause a fire.
Replace parts carefully, always use Samsung parts. Take care to note the exact location of parts and also
cable routing before dismantling any part of the machine. Ensure all parts and cables are replaced correctly.
Please carry out the following procedures before dismantling the printer or replacing any parts.
(1) Check the contents of the machine memory and make a note of any user settings. These will be erased if the
mainboard is replaced.
(2) Ensure that power is disconnected before servicing or replacing any electrical parts.
(3) Disconnect printer interface cables and power cables.
(4) Only use approved spare parts. Ensure that part number, product name, any voltage, current or temperature
rating are correct.
(5) When removing or re-fitting any parts do not use excessive force, especially when fitting screws into plastic.
(6) Take care not to drop any small parts into the machine.
(7) Handling of the OPC Drum
- The OPC Drum can be irreparably damaged if it exposed to light.
Take care not to expose the OPC Drum either to direct sunlight or to fluorescent or incandescent room
lighting. Exposure for as little as 5 mins can damage the surface’s photoconductive properties and will result
in print quality degradation. Take extra care when servicing the printer. Remove the OPC Drum and store it in
a black bag or other lightproof container. Take care when working with the covers(especially the top cover)
open as light is admitted to the OPC area and can damage the OPC Drum.
- Take care not to scratch the green surface of OPC Drum Unit.
If the green surface of the Drum Cartridge is scratched or touched the print quality will be compromised.
Service Manual
1-3
Samsung Electronics
Precautions
Service Manual
1-4
Samsung Electronics
Precautions
Certain semiconductor devices can be easily damaged by static electricity. Such components are commonly called
“Electrostatically Sensitive (ES) Devices”, or ESDs. Examples of typical ESDs are: integrated circuits, some field
effect transistors, and semiconductor “chip” components.
The techniques outlined below should be followed to help reduce the incidence of component damage caused by
static electricity.
Caution >>Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
1. Immediately before handling a semiconductor component or semiconductor-equipped assembly, drain off any
electrostatic charge on your body by touching a known earth ground. Alternatively, employ a commercially avail-
able wrist strap device, which should be removed for your personal safety reasons prior to applying power to the
unit under test.
2. After removing an electrical assembly equipped with ESDs, place the assembly on a conductive surface, such as
aluminum or copper foil, or conductive foam, to prevent electrostatic charge buildup in the vicinity of the assem-
bly.
3. Use only a grounded tip soldering iron to solder or desolder ESDs.
4. Use only an “anti-static” solder removal device. Some solder removal devices not classified as “anti-static” can
generate electrical charges sufficient to damage ESDs.
5. Do not use Freon-propelled chemicals. When sprayed, these can generate electrical charges sufficient to dam-
age ESDs.
6. Do not remove a replacement ESD from its protective packaging until immediately before installing it. Most
replacement ESDs are packaged with all leads shorted together by conductive foam, aluminum foil, or a compa-
rable conductive material.
7. Immediately before removing the protective shorting material from the leads of a replacement ESD, touch the pro-
tective material to the chassis or circuit assembly into which the device will be installed.
8. Maintain continuous electrical contact between the ESD and the assembly into which it will be installed, until com-
pletely plugged or soldered into the circuit.
9. Minimize bodily motions when handling unpackaged replacement ESDs. Normal motions, such as the brushing
together of clothing fabric and lifting one’s foot from a carpeted floor, can generate static electricity sufficient to
damage an ESD.
1. Exercise caution when replacing a super capacitor or Lithium battery. There could be a danger of explosion and
subsequent operator injury and/or equipment damage if incorrectly installed.
2. Be sure to replace the battery with the same or equivalent type recommended by the manufacturer.
3. Super capacitor or Lithium batteries contain toxic substances and should not be opened, crushed, or burned for
disposal.
Service Manual
1-5
Samsung Electronics
Product Specifications
2
2. Product Specifications
2.1 Product Overview
Item
Basic Model
Series Model
Maket of Sales
CLP-600
Descriptions
Service Manual
2-1
Samsung Electronics
Product Specifications
2.2 Specifications
Specifications are correct at the time of printing. Product specifications are subject to change without notice.
See below for product specifications.
* Print speed will be affected by Operating System used, computing performance, application software, connecting
method, media type, media size and job complexity.
Service Manual
2-2
Samsung Electronics
Product Specifications
Service Manual
2-3
Samsung Electronics
Product Specifications
Service Manual
2-4
Samsung Electronics
Product Specifications
Service Manual
2-5
Samsung Electronics
Product Specifications
Service Manual
2-6
Samsung Electronics
System Overview
3
3. System Overview
This chapter describes the functions and operating principles of the main components.
Fan
Exit Fuser
Fan
Color Regi
Sensor
DEV. - Black
LSU:4Beam PTB
DEV. - Yellow
DEV. - Magenta
Waste Tank
DEV. - Cyan MPF Path
Paper
ath
SMPS
Charge Roll P
Feeder F
MP
Cassette Path
Cassette
MPF
MPF
SCF Path
Service Manual
3-1
Samsung Electronics
System Overview
3.1.2 Sensor
Exit
Thermostat
Thermistor
Color Regi
(2EA)
CRUM
(4EA)
CTD
Toner Full
CRUM
Humidity
Paper Regi
Temperature
MPF paper
empty
Service Manual
3-2
Samsung Electronics
System Overview
1) OPC Unit
Images are created on the OPC unit using an electro-photographic process. The unit consists of:-
* OPC Drum
used to collect waste toner remaining on the OPC drum,
* Charge Roller Assy
3) Transfer Roller
Once the complete, full colour, image, has been built up on the ITB the Transfer Roller is used to
transfer the image onto paper. This is called the T2 Transfer (Secondary Image Transfer)
Pick-up Roller picks up paper, controls drive, feeds paper, removes static electricity, and so on.
> Spec.
* Paper arrange way : Side Registration
* Paper Direction : FISO (Front-in, Side-Out)
* Cassette Type : A4, Ltr
* Paper Discharge : Separation Claw
* Capacity : 250 Sheets (Standard paper 75mg/m? 20lb)
* Paper Size : A4, Letter
* Paper Weight (average) : 60~90g/m2 (16~24lbs)
* Paper Type : General Printing Paper
* Additional Function : Paper Empty Sensor
> Spec.
* Paper arrangement : Side Registration
* Paper Direction : FISO (Front-in, Side-Out)
* Cassette Type : A4, Ltr
* Paper Discharge : Separation Claw
* Capacity : 500 Sheets (Standard paper 75mg/m2 20lb)
* Paper Size : A4, Letter
* Paper Weight (average) : 60~90g/m2 (16~24lbs)
* Paper Type : General Printing Paper
* Additional Function : Paper Empty Sensor
Service Manual
3-3
Samsung Electronics
System Overview
7) Feeder
* Paper Arrangement : Side Registration.
* Power : Main Motor (Stepper Motor)
* Paper Management : Shutter Method
8) Duplex Unit
The Duplex Unit is not used.
9) Exit Unit
The Exit Unit guides paper that is just about to leave the print engine. Printed-paper is discharged
by the Exit Roller and Kicker into the Output Tray.
> Spec.
* Capacity : 250 sheets (Standard A4, 75g/m2)
* Paper Direction : Face Down
* Exit Drive Roller : It is driven by Main Motor (BLDC), and it rotates clockwise for normal
feed and antic-clockwise when reverse feeding for duplex printing.
* Sensor : There is photo interrupt sensing (GPIS73)
* Jam Detect : Exit Cover Open.
Service Manual
3-4
Samsung Electronics
System Overview
12) LSU
This is a core part of LBP. It forms a latent image on the surface of OPC drum using a static
charge.
* Resolution: Real 600 dpi
* Motor : Brushless DC motor PWM control.
Service Manual
3-5
Samsung Electronics
System Overview
3.1.3 EP process
1)Charging
Roller charging
Roller resistivity : ~ 10^5 ohm-cm
Applied voltage : -1.0 ~ -1.5kV
Charge acceptance : ~ -550V
OPC coating thickness : ~ 20um
OPC diameter : •’24mm
Non eraser system
Charging roller
OPC
2)Exposing
LSU OPC Drum
Beam F-θ Lens
One polygon motor ( 8 facet ) Mirror Detector
Dual beam LD (2ea)
LD wavelength : 785nm K OPC
Polygon motor rpm : ~ 21600 Polygon
Motor
LSU energy : ~ 0.5uJ/cm^2 Collimating C OPC
OPC exposed potential : ~ 50V Lens
M OPC
Laser
Diode (Dual
Cylindrical
Mirror
Y OPC
Beam)
Service Manual
3-6
Samsung Electronics
System Overview
3)Developing
OPC
Developing roller
Toner supplying belt Supplying roller
4)Transfer
Transfer Belt
Attraction Roller
Service Manual
3-7
Samsung Electronics
System Overview
5)Fusing
Pressure roller
Warm-up time
(80sec)
Heat roller
CLP-500 CLP-600
Service Manual
3-8
Samsung Electronics
System Overview
Developing Roller
drive gear OPC drive gear
Black Toner Cartridge
Cyan Toner Cartridge
Magenta Toner Cartridge
Yellow Toner Cartridge
PTB Unit
Handle
OPC Drum
Cartridge guide
High voltage contact point
(Developing Roller)
Sheet Waste
Waste toner tank Cleaning Blade
Charge Roller
OPC Drum
Shaft OPC
Dr. Blade
Service Manual
3-9
Samsung Electronics
System Overview
OPC Cleaning: Collect the toner by using Cleaning Blade (urethane) transport to the waste toner tank by sheet waste
OPC Drum protecting Shutter : No (Take care of impact)
Method of Toner supply : Toner is transported to the developing roller by supply belt
Regulating Toner level : Regulating Toner level by Sus. Blade
Maintenace of developing gap : Maintenace of developing gap by Gap-ring which is located at the ends of developing
roller
Developing Roller
Sheet Waste
Sus. Blade
Gap-Ring
Service Manual
3-10
Samsung Electronics
System Overview
Drive Roller
Paper Path
Transfer material
Cleaning Blade
Transfer RollerBk
Transfer Roller C
Cleaning Blade
Transfer Roller M
Transfer Roller Y
Waste Toner Tank
Tension Roller
Service Manual
3-11
Samsung Electronics
System Overview
Handle-Unit
Terminal in PCR
Service Manual
3-12
Samsung Electronics
System Overview
Service Manual
3-13
Samsung Electronics
System Overview
Service Manual
3-14
Samsung Electronics
System Overview
The driver board, used in the photoelectric Dry Color Laser Printer Engine, drives two or three stepping motors and
motivates various fans, solenoids and clutches. It also activates sensors and transmits their signals to the main board.
Driver Board
Solenoid Pickup/MP/DUP
Driver Solenoid
Clutch Feed/Y_DEVE
Driver Clutch
MP_EMPT/
Sensor
EXIT/EMPT/
Driver
FEED Sensor
Service Manual
3-15
Samsung Electronics
System Overview
1) Using two TEA3718 ICs, the driver board drives one stepping motor.
2) When driving only four OPC, the driver board drives two stepping motors. When additionally driving the yellow
developer, it drives three stepping motors.
According to the printing sequence and B/W printing option, the driver board puts on/off the correspondent clutch, trans-
mitting or intercepting the power.
According to the printing sequence and Duplex(reserved) option, the driver board drives correspondent solenoid.
The driver board drives the fans for Fuser and SMPS.
The driver board activates MP_EMPT / EXIT / EMPT / FEED Sensors and transmits their signals to the Main Board.
Service Manual
3-16
Samsung Electronics
System Overview
Deve CRUM, used in the photoelectric Dry Color Laser Printer developer, is mounted on the developer. It exchanges
information of the developer with the main body, and at the same time identifies the qualification status and kind of the
developer, and measures the amount used.
A0 Chip Enable
Main EEPROM A1
(M24C04-WMN6)
A2
- The Deve CRUM makes out whether the part used is qualified or disqualified by reading the data of the EEPROM.
- When the data of the EEPROM is normal, the machine will operate normally, and when the data is abnormal
or unrecognizable, it will output alarm message and stops printing.
- Through "device select code" and "chip enable input", it judges whether a correct developer with correct color
is mounted or not.
- The Deve CRUM records the information of dot count into EEPROM, informing the amount of toner used and
left over.
Service Manual
3-17
Samsung Electronics
System Overview
The Belt CRUM, used in the transmission belt of the photoelectric Dry Color Laser Printer, is mounted on the belt. It
exchanges information of the belt with the body, identifies qualification status of the belt and measures its usage.
Main EEPROM
(M24C04-WMN6)
- It judges whether the belt is qualified or not, by reading the data of EEPROM.
- When the data of the EEPROM is normal, the machine will operate normally, and when the data is abnormal
or unrecognizable, it will output alarm message and stops printing
- By recording the rotation number of the belt into EEPROM, the belt CRUM lets you know the number used
and the number that may be used.
Service Manual
3-18
Samsung Electronics
System Overview
DEVE
Main CRUM
Service Manual
3-19
Samsung Electronics
System Overview
DEVE
Main CRUM
Service Manual
3-20
Samsung Electronics
System Overview
1 27
2 28
Service Manual
3-21
Samsung Electronics
System Overview
Fusible
+24V
+24VF
+5V
+5VL
+24VF GNDA
Service Manual
3-22
Samsung Electronics
System Overview
PWM_Charger PWM_Charger 21 22 NC
Service Manual
3-23
Samsung Electronics
System Overview
+24V HVPS
Engine Board
Pull Up
/PWM_T ?
DM7407N
/PWM_Attr
DM7407N
/PWM_Deve
DM7407N
/PWM_Charge
DM7407N
/PWM_AC
DM7407N
/PWM_AC Vp-p
DM7407N
256
H
73.7㎲
Service Manual
3-24
Samsung Electronics
System Overview
+24V HVPS
/Enb_Attr(-DC)
DM7407N
/Enb_Deve AC
DM7407N
Service Manual
3-25
Samsung Electronics
System Overview
300Ω
Hvps Board
Engine Board
2KΩ 2KΩ
2KΩ
Service Manual
3-26
Samsung Electronics
S/W Structure and Descriptions
4
4. S/W Structure and Descriptions
Printer Driver
Language Monitor
Status Monitor
Service Manual
4-1
Samsung Electronics
S/W Structure and Descriptions
User ID + Job ID
+
Printer Driver
Printer Data Language Printer Data
Monitor
Printer Server
(Kernel / NPC)
Printer Name
Port Name Printer Server
User ID
Job ID
(Kernel / NPC)
Printer Server IP Addr SNMP Job ID
Request Printer Status
Printer Status
Status Monitor
Request Job Status
Job Table
Service Manual
4-2
Samsung Electronics
S/W Structure and Descriptions
Service Manual
4-3
Samsung Electronics
S/W Structure and Descriptions
Service Manual
4-4
Samsung Electronics
S/W Structure and Descriptions
Service Manual
4-5
Samsung Electronics
5
Disassembly and Reassembly
Service Manual
5-1
Samsung Electronics
Disassembly and Reassembly
* Use only approved Samsung spare parts. Ensure that part number, product name, any voltage, current or
temperature rating are correct. Failure to do so could result in damage to the machine, circuit overload,
fire or electric shock.
* Do not make any unauthorized changes or additions to the printer, these could cause the printer to mal-
function and create electric shock or fire hazards.
* Take care when dismantling the unit to note where each screw goes. There are 19 different screws. Use of
the wrong screw could lead to system failure, short circuit or electric shock.
* Do not disassemble the LSU unit. Once it is disassembled dust is admitted to the mirror chamber and will
seriously degrade print quality. There are no serviceable parts inside.
* Regularly check the condition of the power cord, plug and socket. Bad contacts could lead to overheating
and firfe. Damaged cables could lead to electric shock or unit malfunction.
Static electricity can damage a PBA, always used approved anti-static precautions when
handling or storing a PBA.
Many of the parts are held in place with plastic latches. The latches break easi-
ly; release them carefully.
To remove such parts, press the hook end of the latch away from the part to
which it is latched.
Service Manual
5-2
Samsung Electronics
Disassembly and Reassembly
Some of the parts in this printer have a limited life, shorter than that of the whole machine. These parts
must be replaced periodically.
The table below shows the interval at which these parts should be replaced.
The table shows the life of each part, and is measured when using A4 paper. When servicing a machine
always check the status of these parts using the control panel and ensure that parts are replaced at the
appropriate times otherwise a general degradation in print quality will occur.
PTB Unit(Paper transfer belt) Black/Color : (35,000 pages@5% coverage) User replace
The life span of each of these parts is stored in memory. The amount of each 'life' used can be checked at
any time using the control panel.
When a part is replaced it is necessary to reset the 'life used' that is stored in memory.
Service Manual
5-3
Samsung Electronics
Disassembly and Reassembly
* Clean the printer with a soft, lint free, cloth dipped in a "Recommended cleaner"
"Recommended cleaner" can be purchased from our service center. (where available)
* Do not touch the transfer roller when cleaning the inside of the printer. Grease and oils from the
skin will contaminate the surface and reduce print quality.
* Do not touch transfer roller when cleaning inside of machine. If transfer roller gets dirty, printing
quality could be low.
Service Manual
5-4
Samsung Electronics
Disassembly and Reassembly
Service Manual
5-5
Samsung Electronics
Disassembly and Reassembly
Service Manual
5-6
Samsung Electronics
Disassembly and Reassembly
Service Manual
5-7
Samsung Electronics
Disassembly and Reassembly
Service Manual
5-8
Samsung Electronics
Disassembly and Reassembly
Service Manual
5-9
Samsung Electronics
Disassembly and Reassembly
1. Pull the side handle to open the Right Cover Ass'y and then press down firmly unit the Toner Cartridges
are ejected.
Service Manual
5-10
Samsung Electronics
Disassembly and Reassembly
MargentaToner Cartridge
YellowToner Cartridge
4. PTB Unit by releasing the PTB Lock Lever on left side of the Right Cover Ass'y.
PTB Unit
Lock Lever
Service Manual
5-11
Samsung Electronics
Disassembly and Reassembly
Service Manual
5-12
Samsung Electronics
Disassembly and Reassembly
Cassette
2. Carefully release the three Hooks using a flat bladed screwdriver, as shown below.
Hook
Service Manual
5-13
Samsung Electronics
Disassembly and Reassembly
Cover-M-Front
Screw
Screw
Screw
Service Manual
5-14
Samsung Electronics
Disassembly and Reassembly
5. First lift the printer, carefully release the Hooks on the both side using a flat bladed screwdriver and then remove
the Cover- M-Deco.
Cover-M-Deco
6. Take care to unplug the one connector from the LCD PBA.
Connector
(LCD PBA)
Cover-M-Deco
Service Manual
5-15
Samsung Electronics
Disassembly and Reassembly
1. Remove the four screws from the OP Cover Ass'y and remove it.
OP Cover Ass’y
2. Remove the nine screws from the LCD PBA and then remove the Keys and LCD PBA, as shown below.
Cap2
LCD PBA
OPE Key2
Cap1
OPE Key1
Service Manual
5-16
Samsung Electronics
Disassembly and Reassembly
Rear Cover
Screw
Screw
Screw
Screw
2. First lift the printer, carefully release the Left Side Hook using a flat bladed screwdriver, as shown below.
Service Manual
5-17
Samsung Electronics
Disassembly and Reassembly
3. Release the Middle Hook and then carefully release the Right Side Hook in the direction of arrow, as shown
below.
2
1
Service Manual
5-18
Samsung Electronics
Disassembly and Reassembly
1. Remove the one screw from the left side hinge, as shown below.
Screw
2. Remove the one screw from the right side hinge, as shown below.
Hinge Screw
Service Manual
5-19
Samsung Electronics
Disassembly and Reassembly
3. First lift the left side of the Right Cover Ass'y and then pull the right side of the Right Cover Ass'y in the direction
of arrow, as shown below.
2
Right Cover Ass’y
Service Manual
5-20
Samsung Electronics
Disassembly and Reassembly
Screw Screw
Screw Screw
Left Cover
Service Manual
5-21
Samsung Electronics
Disassembly and Reassembly
5.4.6 Fuser
>> Before disassembling it :
* open the Right Cover Ass'y (Refer to 5.3.3)
Exit Cover
Handle-Fix-Fuser
Handle-Fix-Fuser
Service Manual
5-22
Samsung Electronics
Disassembly and Reassembly
Fuser
Service Manual
5-23
Samsung Electronics
Disassembly and Reassembly
Exit Cover
2. Remove the two screws located left side the Top Cover Ass'y, as shown below.
Screw Screw
Service Manual
5-24
Samsung Electronics
Disassembly and Reassembly
3. Remove the three screws located top and right side the Top Cover Ass'y, as shown below.
Then remove the Top Cover Ass'y.
Screw Screw
Screw
Service Manual
5-25
Samsung Electronics
Disassembly and Reassembly
1. If necessary, remove the Exit Cover in the direction of arrow, as shown below.
Exit Cover
1 2
Service Manual
5-26
Samsung Electronics
Disassembly and Reassembly
Pin
E-Ring
Gear-Fuser Drive
NOTICE : Be aware of the E-Ring and Pin to ensure they are not lost.
2. Unplug the four connectors from the two OPC Drive Motors, Fuser Drive Motor and DEVE Drive Motor, as
shown below.
OPC Drive
Motor Fuser Drive
Motor
DEVE Drive
Motor
OPC Drive
Motor
Service Manual
5-27
Samsung Electronics
Disassembly and Reassembly
3. Remove the six screws from the Main Drive and then pull the Main Drive Ass'y, as shown below.
Screw Screw
Screw Screw
Screw
Screw
Service Manual
5-28
Samsung Electronics
Disassembly and Reassembly
HVPS
Screw Screw
Hook
Hook
Hook
Hook
Service Manual
5-29
Samsung Electronics
Disassembly and Reassembly
HVPS
Main
Frame
Service Manual
5-30
Samsung Electronics
Disassembly and Reassembly
To Main PBA
<HVPS>
Service Manual
5-31
Samsung Electronics
Disassembly and Reassembly
1. Remove the five screws from the Bracket Conn and remove it, as shown below.
Bracket-Conn
Screw Screw
Screw
Screw
Screw
2. Unplug the all connectors and then remove the four screws from the Main PBA.
Screw Screw
Screw Screw
Service Manual
5-32
Samsung Electronics
Disassembly and Reassembly
3. Remove the two screws securing the Bracket-NPC from the Bracket-Cont Lower and then remove the Main
PBA(with PCB Sub-PCI NPC), as shown below.
Screw
Bracket-Cont Lower
Bracket-NPC
Screw
4. Pull the PCB Sub-PCI NPC from the Main PBA, as shown below.
Main PBA
Service Manual
5-33
Samsung Electronics
Disassembly and Reassembly
LSU_LD Panel
TH_Fuser HVPS1 HVPS2
Temp_In
BLDC DEVE YM
USB
Driver
To PCI NPC
CN200
SCF
Cover Open
Temp_Out n24V_EN_Out
SMPS
<Main PBA>
To Main PBA
Line
Service Manual
5-34
Samsung Electronics
Disassembly and Reassembly
1. Remove the three screws from the Bracket-Cont Lower and then remove it.
Braket-Cont Lower
Screw
Screw
Screw
2. Unplug the all connectors and remove the three screws from the PBA Sub-Driver and then remove it, as shown
below.
Screw Screw
Screw
PBA Sub-Driver
Service Manual
5-35
Samsung Electronics
Disassembly and Reassembly
Fan
Exit SMPS
Step Motor
Fan Fuser
To Main PBA
Sol_MP
Sol_Pickup
MP EMPT Feed
EMPT
<PBA Sub-Driver>
Service Manual
5-36
Samsung Electronics
Disassembly and Reassembly
CRUM BD
Main PBA
2. First release the Hook and then remove the CRUM Unit in the direction of arrow.
CRUM Unit
Hook
Service Manual
5-37
Samsung Electronics
Disassembly and Reassembly
3. Remove the PBA Sub-DEVE_CRUM from the Cover-CRUM BD, as shown below.
PBA Sub-DEVE_CRUM
Cover-CRUM BD
Service Manual
5-38
Samsung Electronics
Disassembly and Reassembly
5.4.14 SMPS
>> Before disassembling it :
* Remove the Top Cover Ass'y (Refer to 5.4.7)
1. Remove the two screws from the SMPS and then pull the SMPS.
Screw Screw
SMPS
2. Unplug the all connectors from the SMPS and then remove the SMPS, as shown below.
Service Manual
5-39
Samsung Electronics
Disassembly and Reassembly
1. Remove the two screws securing the Holder AC Unit and then remove the Holder AC Unit in the direction of arrow.
Holder AC
Harness
Holder AC Unit
Screw
Screw
2. Unplug the Holder AC Unit connector from the SMPS, as shown below.
Connector(Holder AC Unit)
SMPS
Service Manual
5-40
Samsung Electronics
Disassembly and Reassembly
5.4.16 LSU
>> Before disassembling it :
* Remove the Top Cover Ass'y (Refer to 5.4.7)
* Remove the Bracket Conn (Refer to 5.4.11)
* Remove the SMPS (Refer to 5.4.14)
1. Remove the four screws from the Housing-Middle Part and then remove it(with Duct Left Ass'y).
Housing-Middle Part
(with Duct Left Ass’y)
Screw Screw
Screw Screw
Screw
Screw
LSU
Service Manual
5-41
Samsung Electronics
Disassembly and Reassembly
LSU
LSU
LSU
Service Manual
5-42
Samsung Electronics
Disassembly and Reassembly
PBA Sub-Driver
MP Solenoid Connector
2. Remove the one screw from the Gear Cover and then remove it, as shown below.
Screw
Gear Cover
Service Manual
5-43
Samsung Electronics
Disassembly and Reassembly
3. Remove the four screws from the MPF Unit and then remove it.
Screw
Screw
Screw
Screw
MPF Unit
4. Remove the one screw securing the Solenoid-MP and then remove it.
MPF Unit
Solenoid-MP
Service Manual
5-44
Samsung Electronics
Disassembly and Reassembly
5. When if only remove the Pick up Unit, first push the Idle toward the ends of shaft and take out the Pick up Unit in
the direction of arrow, as shown below.
Pickup Unit
1
1
2 Idle
Pickup Unit
Service Manual
5-45
Samsung Electronics
Disassembly and Reassembly
5.4.18 Housing-M-Pick up
1. First turning over, remove the Extension Spring using a Pincette, as shown below.
Exension Spring
2. Pull the Housing-M-Pick up from the Bushing Feed and then remove it in the direction of arrow.
Housing-M-Pickup
Bushing Bushing
Service Manual
5-46
Samsung Electronics
Disassembly and Reassembly
NOTICE : When you reassemble the Housing-M-Pick up make sure that the let and of the Housing-M-Pick up fits
into the Pick up Shaft, as shown below.
Service Manual
5-47
Samsung Electronics
Alignment and Adjustmens
6
6. Alignment and Adjustments
Fan
Exit Fuser
Fan
Color Regi
Sensor
DEV. - Black
LSU:4Beam PTB
DEV. - Yellow
DEV. - Magenta
Waste Tank
DEV. - Cyan MPF Path
Paper
ath
SMPS
Charge Roll P
Feeder F
MP
Cassette Path
Cassette
MPF
MPF
SCF Path
Service Manual
6-1
Samsung Electronics
Alignment and Adjustmens
6.1.2 Jams
MPF Path
MPF Path
Service Manual
6-2
Samsung Electronics
Alignment and Adjustmens
5) Jam MPF
MPF Path
Service Manual
6-3
Samsung Electronics
Alignment and Adjustmens
* Jam0 In Tray 1:
Paper jam in the main cassette.
* Jam0 In MP Tray:
Paper jam in the MP tray
* Jam0 Tray2:
Paper jam in the SCT (Second cassette tray)
* Jam Inside Printer:
Jam 1, Paper is jammed inside the printer.
* Jam In Exit Area:
Jam2, Paper is jammed in the exit area when ejecting paper.
CAUTION: When removing jammed paper, always pull it firmly and evenly without any sudden jerks. If
at all possible, remove the paper as a single sheet. If the paper tears ensures ALL paper
fragments are removed. Any fragments left inside the machine will cause it to jam again.
By selecting the correct paper types, most paper jams can be avoided. If a paper jam occurs, follow the
steps outlined below:
Service Manual
6-4
Samsung Electronics
Alignment and Adjustmens
If paper is jammed in the paper feed area, a lamp turns on at the corresponding location on the Status
map. If you use the CLP-600N, “Jam0 In Tray1” also appears on the display.
1. Using the handle, completely open the access 3. Pull the tray open. After you pull it all the way out,
door. lift up the front part of the tray slightly to release
the tray from the printer.
2. Carefully remove the paper by pulling in the 4. Remove the jammed paper by gently pulling it
direction as shown below. If you cannot find the straight out as shown below.
jammed paper, or if there is any resistance
removing the paper, stop pulling.
CAUTION:
• Do not touch the green surface, the OPC drum,
on the front of each toner cartridge with your
hands or any other material. Use the handle on
each cartridge in order to avoid touching this
area.
When you print using the Multi-purpose Tray and the printer detects that there is either no paper or the
paper has been improperly loaded, a lamp turns on at the corresponding location on the Status map. If you
use the CLP-600N, “Jam0 In MP Tray” also appears on the display.
Service Manual
6-6
Samsung Electronics
Alignment and Adjustmens
If paper is jammed inside the printer, a lamp turns on at the corresponding location on the Status map. If
you use the CLP-600N, “Jam Inside Printer” also appears on the display.
Service Manual
6-7
Samsung Electronics
Alignment and Adjustmens
If paper is jammed in the paper exit area, a lamp turns on at the corresponding location on the Status map.
If you use the CLP-600N, “Jam In Exit Area” also appears on the display.
1. If a long portion of the paper is visible, pull it 3. Open the top cover.
straight out. Open and close the access door
firmly. The printer will resume printing.
If you cannot find the jammed paper, or if there
is any resistance removing the paper, stop
pulling.
CAUTION:
Do not touch the fuser inside the inner cover. It is
hot and could cause burns! The fuser’s operating
temperature is 180°C (356°F). Take care when
removing paper from the printer.
CAUTION:
• Do not touch the green surface, the OPC drum,
on the front of each toner cartridge with your
hands or any other material. Use the handle on
each cartridge in order to avoid touching this area.
• Be careful not to scratch the surface of the paper
transfer belt.
• If you leave the access door open for more than
a few minutes, the OPC drum can be exposed to
light. This will cause damage to the OPC drum.
Close the access door should the installation
need to be halted for any reason.
Service Manual
6-8
Samsung Electronics
Alignment and Adjustmens
5. After removing the jammed paper, check for 7. Close the access door firmly. The printer will
paper which may be jammed in other parts of resume printing.
the printer.
CAUTION:
• Do not touch the green surface, the OPC drum,
Service Manual
6-9
Samsung Electronics
Alignment and Adjustmens
If paper i s j ammed i n the opti onal Tray2, a l amp turns on at the corresponding location on the Status
map. If you use the CLP-600N, “Jam0 In Tray2” also appears on the display.
1. Using the handle, completely open the access 3. Holding the inner cover open, carefully take the
door. jammed paper out of the printer. The inner
cover will then close automatically.
CAUTION:
• Do not touch the fuser inside the inner cover. It
is hot and could cause burns! The fuser’s operat-
ing temperature is 180°C (356°F). Take care
when removing paper from the printer.
• Do not touch the green surface, the OPC drum,
on the front of each toner cartridge with your
hands or any other material. Use the handle on
each cartridge in order to avoid touching this
area.
• Be careful not to scratch the surface of the paper
transfer belt.
• If you leave the access door open for more than
a few minutes, the OPC drum can be exposed
to light. This will cause damage to the OPC
drum. Close the access door should the
installation need to be halted for any reason.
Service Manual
6-10
Samsung Electronics
Alignment and Adjustmens
4. Open the outer jam cover in Tray2. 6. Pull the jammed paper out in the direction
shown. To avoid tearing the paper, pull it out
gently and slowly.
Service Manual
6-11
Samsung Electronics
Alignment and Adjustmens
8. Pull the optional Tray2 open. After you pull it all 10. Slide the tray back into the printer and close
the way out, lift up the front part of the tray the two jam covers.
slightly to release the tray from the printer.
11. Open the access door.
Service Manual
6-12
Samsung Electronics
Alignment and Adjustmens
CAUTION:
If the top cover and access door are not completely
closed, the printer will not operate.
Service Manual
6-13
Samsung Electronics
Alignment and Adjustmens
1. Press the Menu button on the control panel until you see “Information ” on the bottom line of the display..
2. Press the Enter button to access the Menu.
3. Press the scroll button until you see “Demo Page ” on the bottom line.
4. Press the Enter button .
A demo page showing the printer ’s features and capabilities prints out.
1. Press the Menu button on the control panel until you see “Information ” on the bottom line of the display..
2. Press the Enter button to access the Menu.
3. Press the scroll button until you see “Configuration ” on the bottom line.
4. Press the Enter button .
A demo page showing the printer ’s features and capabilities prints out.
Service Manual
6-14
Samsung Electronics
Alignment and Adjustmens
1. In ready mode press the Menu button on the control panel several times until you see ‘Setup ’on the bottom line
of the display.
2 Press the Enter button to access the menu.
3 Press the scroll button until ‘Maintenance ’ displays on the bottom line.
4 Press the Enter button
5 When ‘Check Toner ’ displays on the bottom line,,press the Enter button .
6 Press the scroll button until the color of the toner cartridge you want to check displays on the bottom line.
7 Press the Enter button The display shows the percentage of the remaining toner.
8. Press the Upper Level button to return to step 6 and select a different cartridge.
9. To return to the Ready condition press the Upper Level button several times until 'Ready' appears in the display
1. In ready mode press the Menu button on the control panel everal times until you see ‘Setup ’on the bottom line
of the display.
2 Press the Enter button to access the menu.
3 Press the scroll button until ‘Maintenance ’ displays on the bottom line.
4 Press the Enter button
5 When ‘Check Others ’ displays on the bottom line,,press the Enter button .
6 Press the scroll button until the item you want to check displays on the bottom line.
7 Press the Enter button The display shows the percentage of item.
8. Press the scroll button display either 'Image Count' or 'Reset'
9a. Choose 'Reset' and press enter to reset the counter after replacing a consumable item
or
9b Choose Image count to display the counter.
10. Press the Upper Level button to return to step 7 and select a different choice or press it a second time to return to step
6 and choose a different item.
11. To return to the Ready condition press the Upper Level button several times until 'Ready' appears in the display.
Service Manual
6-15
Samsung Electronics
Alignment and Adjustmens
6.5.1 Display
Message Description
Ready •The printer is on-line and ready to print.
• If you press the On Line/Continue button, the printer goes off-line.
Offline •The printer is off-line and cannot print.
•If you press On Line/Continue ,the printer switches to on-line.
Processing... •The printer is printing.
•If you want to cancel printing,press Cancel .
Sleeping... •The printer is in Power Save mode, using less power.When a print job is
received from the computer or if any button is pressed,the printer switches to
on-line.
•To deactivate the Power Save mode or change the power-saving time.
Service Manual
6-16
Samsung Electronics
Alignment and Adjustmens
6.5.2 Buttons
Message Description
When a paper jam occurs, a lamp turns on at the corresponding location on the Status map so that
you can locate the paper jam. If you use the CLP-600N, the display on the control panel also
shows the corresponding error message, indicating the location of the jam. For details on the
meaning of the LEDs and error messages.
On When a toner cartridge is empty, a corresponding lamp, indicating the color of the
toner cartridge, turns on. Replace the corresponding toner cartridge with a new
one.
Or, if you have installed an invalid toner cartridge, a corresponding lamp turns on.
Install only Samsung toner cartridges, designed for your printer.
Otherwise, if you have installed the toner cartridge into improper cartirdge slot, a
corresponding lamp turns on. Install the toner cartridge into each proper cartridge
slot.
Blanking When a toner cartridge is low, a corresponding lamp, indicating the color of the
toner cartridge, blinking. Order a new toner cartridge. You can Temporarily improve
print quality by redistributing the toner.
Service Manual
6-17
Samsung Electronics
Alignment and Adjustmens
Message Description
Green On The printer is on-line and can receive data from the computer.
Blanking • When the light blinks slowly, the printer is receiving data from the
computer.
• When the light blinks quickly, the printer is receiving and printing
data.
Blanking A minor error has occurred and the printer is waiting for the error to
be cleared. Check the display message or SmartPanel. When the
problem is cleared, the printer resumes printing. If you want to
ignore this warning, press this button.
Service Manual
6-18
Samsung Electronics
Alignment and Adjustmens
You can configure your printer from the printer’s control panel.You can also use the control panel menus while the printer
is in use.
1. In ready mode press the Menu button until you see the menu you want on the bottom line of the display.
2. Press the Enter button to access the menu.
3. Press the scroll button until the menu item you want displays on the bottom line.
4. Press the Enter button to confirm the selected item.
5. If the menu item has submenus, repeat steps 3 and 4.
6. Press the scroll button until the setting option you want displays on the bottom line or enter the required value.
6. Press the Enter button to save your input or selection.
- An asterisk (*) appears next to the selection on the display, indicating that it is now the default.
8. To exit the menu, press the Upper Level button repeatedly, or the Cancel button .
- After 60 seconds of inactivity (no key has been pressed), the printer automatically returns to ready mode.
NOTE: Print settings made from the printer driver override the settings on the control panel.
Service Manual
6-19
Samsung Electronics
Alignment and Adjustmens
Cleaning blade
1. OPC drum
2. Charger roller
LSU
Doctor blade
4. Developing roller
3. Supply roller
Service Manual
6-20
Samsung Electronics
Alignment and Adjustmens
EDC Mode is feature that allows the engineer to check the condition of the print engine. It can check the operating condi-
tion of the motors, sensors, solenoids and clutches, measure the High Voltage from the HVPS and check the operation of
the fuser and LSU.
a) Turn on the printer while pressing the “Enter” key. Hold the key until ‘Select Test mode’ appears in the display.
b) Press the direction key until “<Ready..200x xx xx>” is displayed.
c) Press the “Enter” key.
d) <Enter Access Key> appears in the display. Press the cancel key twice.
Note. There are a number of other test modes. Only EDC Test and Panel Tests should be used by service engineers, all
other functions are for factory use only.
6.6.1.1 Functions of the keys on the Panel and how to use them.
Key Function Description
On Line Not used
Upper Menu Stop/Move Stop Stop the selected Function or go to Upper Menu.
Upper Line : Upper Line messages mainly show the current test menu or sub-menu.
[Main Menu] or [Function] is displayed.
Lower Line : Lower Line messages mainly the current test and status.
Service Manual
6-21
Samsung Electronics
Alignment and Adjustmens
Service Manual
6-22
Samsung Electronics
Alignment and Adjustmens
<How to operate>
a) Press the "<" or ">" key until "Motor Test" is displayed.
b) Press the "Enter" key to select this function.
c) Press the "<" or ">" key until you see the name of the motor you wish to test.
d) Press the "Enter" key to run the test. The test is stopped by pressing the "Upper Level" key.
e) Pressing the "Upper Level" key when the test is already stopped will return to step 'c' above.
f) Pressing the "Upper Level" key again will return to the EDC main menu.
Service Manual
6-23
Samsung Electronics
Alignment and Adjustmens
This function allows the operation of various solenoids and clutches to be checked.
<How to operate>
a) Press the "<" or ">" key until "Solenoid Test" is displayed.
b) Press the "Enter" key to select this function.
c) Press the "<" or ">" key until you see the name of the clutch or solenoid you wish to test.
d) Press the "Enter" key to run the test. The test is stopped by pressing the "Upper Level" key.
e) Pressing the "Upper Level" key when the test is already stopped will return to step 'c' above.
f) Pressing the "Upper Level" key again will return to the EDC main menu.
Service Manual
6-24
Samsung Electronics
Alignment and Adjustmens
<How to operate>
a) Press the "<" or ">" key until "Sensor Test" is displayed.
b) Press the "Enter" key to select this function.
c) Press the "<" or ">" key until you see the name of the sensor you wish to test.
d) Press the "Enter" key to display the sensor status. If the sensor actuator is moved the displayed status will change to
reflect the new sensor position..
e) Pressing the "Upper Level" key will return to step 'c' above.
f) Pressing the "Upper Level" key again will return to the EDC main menu.
Service Manual
6-25
Samsung Electronics
Alignment and Adjustmens
This function allows the Fuser, LSU Motor and Laser Diode to be tested.
<How to operate>
a) Press the "<" or ">" key until "LSU Test" is displayed.
b) Press the "Enter" key to select this function.
c) Press the "<" or ">" key until you see the name of part you wish to test.
d) Press the "Enter" key to run the test. The test is stopped by pressing the "Upper Level" key.
e) Pressing the "Upper Level" key when the test is already stopped will return to step 'c' above.
f) Pressing the "Upper Level" key again will return to the EDC main menu.
• The LSU Motor Lock Time is a maximum 15 seconds depending on the environment. It may take over 15 seconds until
the <Succeed> or <Failed> message is displayed.
• For safety - after printing a test pattern if you need to return to EDC mode turn the printer off and then re-enter EDC.
Service Manual
6-26
Samsung Electronics
Alignment and Adjustmens
This function allows you to test the overall function of the print engine. You can select either a 4 * 4 color bar pattern or a
solid color pattern. If the solid pattern is selected 4 pages are printed - one for each color. You can also print the EDC
Mode Menu Map.
<How to operate>
- Explore the menu until "Test Print" message is displayed on LCD.
- Press "Enter" key to select sub items.
- In the "Select Tray" menu, select paper tray from which paper is fed.
- In the "Select Pattern" menu, choose test pattern.
- If "Print Pattern" is selected, printing starts.
For safety - after printing a test pattern if you need to return to EDC mode turn the printer off and then re-enter EDC
Mode by turning power on whilst holding in the "Enter" key.
Service Manual
6-27
Samsung Electronics
Alignment and Adjustmens
<How to operate>
a) Press the "<" or ">" key until "HVPS Test" is displayed.
b) Press the "Enter" key to select this function.
c) Press the "<" or ">" key until you see the name of the voltage you wish to test.
d) Press the "Enter" key to select the test.
e) Press the "<" or ">" key to select the appropriate Duty Cycle and press "Enter" to start the test
The test is stopped by pressing the "Upper Level" key.
The display shows the acceptable range for this setting (column 4 in the table below)
The mid range (nominal) voltage is shown in column 3 in the table below.
e) Pressing the "Upper Level" key when the test is already stopped will return to step 'c' above.
f) Pressing the "Upper Level" key again will return to the EDC main menu.
* The allowed tolerance is commonly +/- 3%, this is the value Displayed, in case of "Dev AC", it is the value of Vpp.
Service Manual
6-28
Samsung Electronics
Troubleshooting
7
7. Troubleshooting
7.1 Procedure of Checking the Symptoms
Before attempting to repair the printer first obtain a detailed description of the problem from the customer.
Power On
Refer to
"7.1.1 Basic Check List"
OP Panel - No Power
ON? - LCD Module
- Main PBA
Ready Indicate
or Refer to
Power Save "Error Message"
"7.5 Error Message"
Printing Refer to
guality is "7.2 Solution of Image Problem"
normal?
END
Service Manual
7-1
Samsung Electronics
Troubleshooting
• Is there a problem?
--> If there is an error see section 2) or 3) above.
• Try printing a test page from a computer.
--> If there is an error check cables and driver installation.
Service Manual
7-2
Samsung Electronics
Troubleshooting
1. The printer does not work no matter how long you wait.
A. Is the Power Switch (printer and wall socket) turned on ?
B. Is the Power Cord connected to the printer correctly ?
C. Is the Power cord connected to the wall socket correctly ?
D. Is wall socket working ?
E. Is the unit rated at the same voltage as the supply ?
2. Does the Fan work when power is turned on?
A. Check the connectors on the SMPS.
B. Check the fuses in the SMPS.
C. Check any error message display on the LCD panel and refer to the troubleshooting section 7.5
1. Ensure the installation surface is flat, level and free from vibration.
If necessary move the printer.
2. Ensure that the temperature and humidity of the surroundings are within specification
If necessary move the printer.
3. Ensure that the printer is position away from any air conditioning or other heating or cooling equipment. Also ensure
that is not positioned in a direct draft from any air conditioning, fan or open window.
If necessary move the printer.
4. Ensure the printer is not positioned in direct sunlight.
If it is unavoidable use a curtain to shade the printer.
5. Ensure the printer is installed in a clean dust free environment.
Move the printer to clean area if necessary.
6. Some industrial or cleaning processes give of fumes which can affect the printer.
Move the printer away from this type of air pollution
Service Manual
7-3
Samsung Electronics
Troubleshooting
The length of life of consumable components is displayed either by operating time (% of life) or quantity of output. The
printer will not work if any of these parts have exceeded there expected life. When a user replaces any of these consumable
parts they must reset the appropriate counter using the maintenance menus (see section 7.4).
The printer calculates the working time and quantity of output for each component and saves this information.
1. The Working time for each component (OPC Drum, Toner Cartridge, Image Transfer Belt, Fuser Unit) is measured
every 30 seconds when the Transport Motor and Fusing Contact Motor are active.
2. In order to calculate the number of images printed 1 is added to the appropriate counter every 30 seconds. The
amount of waste toner is calculated based on the number of pixels in the image.
3. When the user replaces any of the consumable parts and resets the appropriate counter it starts again from 0.
Service Manual
7-4
Samsung Electronics
Troubleshooting
- No Image
Cause Sequence of Treatment
Toner cartridge contacts dirty or not making Check and clean the toner contacts.
good contact or empty Toner Cartridge Re-seat the Toner Cartridge.
(when printing a single color image) Replace the Toner cartridge
PTB cartridge contacts dirty or not making Check and clean the PTB contacts.
good contact or Faulty PTB unit Re-seat the PTB Unit.
Replace PTB Unit
LSU cable harness plugs not fitted properly Check the connectors on the LSU Unit and
or faulty LSU. main PWA are properly inserted.
Replace the LSU Unit, cables or MAIN PWA
as required
OPC Drum BIAS contacts dirty or not mak- Clean Drum contacts..
ing good contact. Replace the Toner Cartridge.
Charge Voltage of the OPC Drum is unstable. Replace the HVPS Board.
PTB Unit belt is contaminated or damaged. Replace the PTB Unit Belt.
Service Manual
7-5
Samsung Electronics
Troubleshooting
Paper Path is contaminated. Open covers fully and clean the Paper Path.
Pressure Roller of Fuser Unit is contaminated. Clean or replace the Fuser Unit.
If the background is contaminated with only Replace the appropriate Toner Cartridge
one color.
If Printing Density is dark(one color only). Replace the appropriate Toner Cartridge
Poor toner transfer to OPC-one color only Check and clean Toner contacts
Replace the appropriate Toner Cartridge
Poor toner transfer to OPC- al colors Check and clean Toner, PTB and OPC unit
contacts
Ensure TDC process is enabled.
If problem persists replace the OPC Drum
Poor toner transfer to PTB Unit Check and clean PTB Unit contacts.
Re-install or replace the PTB Unit.
PTB Bias voltage incorrect. Check and clean PTB Unit contact.
Replace the HVPS.
Service Manual
7-6
Samsung Electronics
Troubleshooting
Lens Cover of LSU is damaged or dirty. Clean the Lens Cover of LSU.
Replace the LSU if the glass is damaged
- Offset Image
Cause Sequence of Treatment
Contamination of the Paper Path. Open the covers, check and clean the Paper
Path.
Problem transferring intermediate image onto Check and clean T2 roller contacts
paper Check T2 Solenoid and cam operation - ensure
T2 comes properly into contact when solenoid
operates.
Service Manual
7-7
Samsung Electronics
Troubleshooting
If the alignment betweem the OPC and PTB Re-install the Toner Cartridge and PTB Units.
Units is not carrect.
Uneven contact between OPC and PTB or Re-install or replace the PTB Unit.
between PTB and T2 roller. Check T2 roller, solenoid and cam operation.
Uneven contact between OPC and PTB or Re-install or replace the PTB Unit.
between PTB and T2 roller. Check T2 roller, solenoid and cam operation.
Uneven color may occur when a toner Make test printing a couple of times.
cartridge has just been installed.
Moisture or wet paper. Ensure paper is stored properly and is not damp.
Check paper storage conditions.
Fault occurs in the MPF Tray Printing only. Replace the MPF Tray Unit.
Service Manual
7-8
Samsung Electronics
Troubleshooting
- Lateral Lines
Cause Sequence of Treatment
Service Manual
7-9
Samsung Electronics
Troubleshooting
7.3.2 JAM 0
3. Check if the surface of the Pick-Up 3. Clean the surface of the Pick-Up
Roller is clean. Roller with IPA or water.
4. Check the Feed Sensor is not 4. Replace the main PBA or Sensor.
sticking by using the EDC Mode
(When “JAM-0” occurs even
though the paper feeds into the
printer.)
Service Manual
7-10
Samsung Electronics
Troubleshooting
1. The Exit Sensor is defective if Jam 1. Check if the Exit Sensor Actuator is
2 occurs after the paper is broken or damaged.
completely fed out of the printer. • Check if the Exit Sensor Actuator
This can happen if the actuator is deformed (Check that the senor
sticks open or is slow to close. arms are not deformed).
• Check for Burrs or rough edges in
the Exit Actuator assembly, and
MPF Path
check that the sensor arms are
free to move.
• Check for foreign objects
obstructing the Exit actuator.
Service Manual
7-11
Samsung Electronics
Troubleshooting
7.3.5 Multi-Feeding
1. Check the On/Off operation of the pick-up Solenoid 1. Replace the Solenoid, harness or Main PBA.
using the EDC Mode.
2. Check the Friction Pad surface for dirt or other conta- 2. Clean the Pad-Friction using a lint free cloth and
mination. water or IPA.
3. Check that the paper is not creased, folded or 3. Use fresh paper.
curved.
4. Check that the Paper Guide in the cassette is properly 4. Adjust the Paper Guide and load paper under the
adjusted and that paper is poperly loaded. Finger.
5. Influence of Static Electricity. 5. Fan paper before loading to reduce the effects of static
electricity.
2. If “Accordion” folding occurs between the Fuser and 2. Check if the Paper Guide Ribs on the Exit Unit are
the Exit Unit repeatedly. damaged or contaminated, and check the condition
and operation of the Exit Roller.
3. If the Bearing - Fuser or Gear - Fuser is damaged or 3. Check the SMPS and Main PBA if the Bearing Gear
melted by excessive heat. is melted.
Service Manual
7-12
Samsung Electronics
Troubleshooting
Symptoms Open Fuser / Over Heat / Low Heat displayed on the LCD Panel.
1. Check the continuity of the Thermostat, AC Wire and 1. Replace the whole Fuser assembly if the Thermostat
Heat Lamp. is open circuit, otherwise replace heat lamps as
required..
2. Check the continuity of the Thermistor and thermistor
harness / contacts. 2. Replace broken thermistor or cables as necessary.
3. Test the Heat Lamps and the overheat circuitry. 3. Replace the main PBA id the overheat circuit is faulty..
4. Check the fuser for any evidence of damage due to 4. Replace the Fuser.
overheating or melting.
2. Check the LSU Motor. 2. If the same error recurs replace the main PBA.
7.4.3 Fuser does not work due to the drive gear melting.
Symptoms The fuser gears melt and the roller drive fails.
1. The Fuser makes a noise and fails to operate, rollers - Replace the Fuser.
may not rotate. - Replace the Main PBA.
- Replace the SMPS.
Service Manual
7-13
Samsung Electronics
Troubleshooting
1. Check for a broken or distorted paper empty sensor 1. Replace the Paper Empty Sensor actuator.
actuator. Check that the actuator is not jammed
2. Check the sensor connectors and cable harness. 2. Replace the harness.
Ensure that a signal reaches the main PBA
3. Use the EDC mode to test the actuator. 3. Replace the Sensor Board.
Symptoms The machine remains 'Ready; even when the paper cassette is empty.
1. Check for a broken or distorted paper empty sensor 1. Replace the Paper Empty Sensor actuator.
actuator. Check that the actuator is not jammed.
2. Check the sensor connectors and cable harness. 2. Replace the harness.
Ensure that a signal reaches the main PBA
3. Use the EDC mode to test the actuator. 3. Replace the Sensor Board.
Symptoms LCD displays "Cover Open" error even though the cover is closed.
1. Check if the Hook Lever inside the Duplex Cover is 1. Replace the Duplex Cover.
broken or distorted.
2. Check the Cover Open sensor, connectors and cable 2. Replace the harness or microswitch as necessary.
harness. Ensure that a signal reaches the main PBA
3. Use the EDC mode to test the actuator. 3. Replace the Sensor Board.
Service Manual
7-14
Samsung Electronics
Troubleshooting
1. Check if the Hook Lever inside the Duplex Cover is 1. Replace the Duplex Cover.
broken or distorted.
2. Check the Cover Open sensor, connectors and cable 2. Replace the harness or microswitch as necessary.
harness. Ensure that a signal reaches the main PBA
3. Use the EDC mode to test the actuator. 3. Replace the Sensor Board.
Symptoms Main Motor does not work and paper does not feed when printing. Jam 0 is displayed.
1. Check if the Motor Harness or Motor PCB is broken 1. Replace the Motor or Motor Harness.
or not.
2. Test the Motor using EDC Mode. 2. Replace the Main PBA.
7.4.9 No Power
Symptoms Power is not supplied to the set, or the LCD display is not on.
1. Check the power supply input and DC voltage output 1. Replace the Power Cable. Replace SMPS fuses. If
from the SMPS. Check the fuses in the SMPS. the fault recurs replace the SMPS.
Check the wall socket.
2. If the SMPS supply is OK, and the LCD still does not 2. Replace cables or LCD Panel Ass'y. Replace the
work check the display connectors and cable harness Main PBA.
3. Check if +24VDC or other Power Supplies are shorted 3. Replace the components used for +24VDC.
out.
Service Manual
7-15
Samsung Electronics
Troubleshooting
1. Use EDC Mode to test the LSU. Check that the 1. Replace the LSU or Main PBA.
+24VCD signal between the main PBA and the LSU
is stable
2. Check that the LSU clock is stable. 2. Replace the Main PBA.
1. "Low Toner" is displayed when under 500page or 1. Using the keypad check which toner is empty and
less toner remains (in any of the cartridges). replace the Toner Cartridge.
2. Check the condition of the contacts on the DEVE - Replace the Toner Joint PBA.
PBA. - Replace the Main PBA.
1. “Ready Replace CART” is displayed when the OPC 1. Replace the OPC Drum.
Image Count value is over 50,000. Image Density
may be reduced. It is possible to continue to print one
Page at a time by pressing the “On-Line” button when
it flashes.
Service Manual
7-16
Samsung Electronics
Troubleshooting
Messages appear on the SmartPanel program window or the control panel display (CLP-600N only) to
indicate the printer’s status or errors. Refer to the tables below to understand the messages’ meanings and
correct the problem if necessary.
Messages and their meanings are listed in alphabetical order.
ACR Calibration During auto color registration, a system Turn the printer off, wait 30 secs and then turn
error occurs so that the registration it auto cleaning mode on.
fails or does not run.
ADC Not Confirm Error A problem has occurred in the ADC Replace the Main PBA if the same symptoms
in the printer. recur.
Adjust Photo LED During auto color registration, the Check the PTB Unit contact status or replace
printer does not recognize the photo the PTB Unit.
LED in the paper transfer belt
assembly.
Cover Open The top cover or access door is open. Close the top cover or access door firmly.
[Color] Toner Empty The corresponding toner cartridge in Replace the corresponding toner cartridge
your printer is empty and the printer with a new one.
does not operate.
Engine Fuser The temperature in the fuser is Unplug the power cord and plug it in again.
Low Heat Error abnormally low.
Engine Fuser The temperature in the fuser is Unplug the power cord and plug it in again.
Over Heat Error abnormally high.
Engine LSU Error A problem has occurred in the LSU Unplug the power cord and plug it in again.
(Laser Scanning Unit) in the printer.
Install The indicated color toner cartridge is Install the corresponding color toner cartridge.
[Color] Toner not installed in the printer.
Install The paper transfer belt is not installed Install the paper transfer belt.
Transfer Belt in the printer.
Invalid Toner An invalid toner cartridge has been Only install Samsung toner cartridges,
[Color] installed. designed for your printer. Or install the toner
cartridge into each proper cartridge slot.
Invalid An invalid paper transfer belt has been Only install Samsung paper transfer belts,
Transfer Belt installed. designed for your printer.
Service Manual
7-17
Samsung Electronics
Troubleshooting
Jam0 In Tray1 A paper jam has occurred in or near Remove the jammed paper from the corre-
Jam0 In Tray2 the indicated tray. sponding tray.
Jam0 In MP Tray
Jam A paper jam has occurred in the paper Remove the jammed paper from the printer.
In Exit Area exit area.
Jam A paper jam has occurred inside the Open the access door and remove the
Inside Printer printer. jammed paper from the printer.
Load The paper size specified in the Load the correct paper in the tray.
[Size] In Tray1 printer properties does not match the
Load paper you are loading.
[Size] In Tray2
Load
[Size] In MP
Low Density The amount of the toner which is Replace the toner cartridge(s) with a new one.
spread on the paper transfer belt for
adjusting auto color registration is
very small, so that the printer does not
recognize the toner during auto color
registration.
Main Motor A problem has occurred in the Unplug the power cord and plug it in again.
Error development motor of the printer.
Memory The printer does not have enough The job automatically clears and the printer
Overflow memory to print the current job. returns to Standby Mode.
An error has occurred in the firmware Lower the print resolution and try again.
program of the printer.
Paper Empty The paper tray has run out of paper. Load paper in the paper tray.
[Size] In Tray1
Paper Empty
[Size] In Tray2
Paper Empty
[Size] In Mp
Paper Empty
[Size] In Manual
Press Continue Button The printer is waiting for the user’s Load a sheet of print material and press the
action before printing from the On Line/Continue button. You need to press
Multi-purpose Tray using the manual the button for each page.
feed mode.
Service Manual
7-18
Samsung Electronics
Troubleshooting
Ready [Color] The corresponding toner cartridge in Redistribute the toner in the corresponding
Low Toner your printer is low on toner. toner cartridge.
Ready The IP address of the printer conflicts Contact your network administrator and
IP Conflict with other devices on the network. choose an address within your subnet
which will not conflict with any other devices.
Replace [Color] The corresponding toner cartridge in If necessary, replace the corresponding toner
Toner your printer is nearly empty. However, cartridge with a new one.
the printer continues printing, even
though print quality is not optimal.
Replace Fuser The life span of the fuser unit has Replace the fuser unit with a new one.
expired.
Replace Fuser The life span of the fuser unit will When “Replace Fuser” appears on the
Soon expire soon. display, replace the fuser unit.
Replace MP The life span of the MP pickup roller Check the MP pickup roller life period or
Pick-roller has expired. replace pickup roller.
Replace The life span of the paper transfer belt Replace the paper transfer belt with a new
Transfer Belt has expired. one.
Replace Transfer The life span of the paper transfer belt When “Replace Transfer Belt” appears on the
Belt Soon will expire soon. display, replace the paper transfer belt.
Replace Tray1 The life span of the Tray1 pickup roller Check the Tray1 pickup roller life period or
Pick-roller has expired. replace Tray1 pickup roller.
Replace Tray2 The life span of the Tray2 pickup roller Check the Tray2 pickup roller life period or
Pick-roller has expired. replace Tray2 pickup roller.
Tray2 Error The optional Tray2 is not properly After turn the printer off and then back on,
installed or connected to the printer. reinstall the optional Tray2.
Tray2 Jam Cover The optional Tray2 jam cover is open. Close the Tray2 cover firmly.
Open
Service Manual
7-19
Samsung Electronics
Exploded Views & Parts List
8
8. Exploded Views and Parts List
Contents
8.1
8.2
8.3
Main
Front Cover
Top Cover
8-2
8-5
8-7
8.4 Right Cover 8-9
8.5 Base Frame 8-11
8.6 Main Frame 8-13
8.7 Fuser 8-16
8.8 Main Drive 8-19
8.9 MPF 8-21
8.10 Pick Up 8-23
8.11 Guide Paper 8-25
8.12 Cassette Unit 8-27
8.13. Cassette(SCF) 8-29
8.14. SCF 8-31
8.15. Guide Upper(SCF) 8-33
8.16. Guide Lower(SCF) 8-35
Part numbers and descriptions are defined according to a company standard. The information below
will help you to understand the part number format and assist when ordering spare parts.
number letter
Ass’y parts and A/S privately used Parts can be distinguished by the part Code and Description.
They are always Type 2 format. The 2 leading characters indicate private or assembly parts.
Service Manual
8-1
8-2
18
25
18-2
18-4
25-2
0 37
8.1 Main
25-1 27-2
Service Manual
18-3
36
20 27-1
36-2 18-1
Exploded Views & Parts List
23 24
27
12 5
22
36-1 21
19 38-2
20
43 42 5
16
17 28
13 44
11 29
7 2 38
(CLP-600N)
9
8 6
38-1
10 4
5
30
15 31
32 34
35
33
14
39
(CLP-600) 1
3
45
26 40 41
Exploded Views & Parts List
Service Manual
8-3
Exploded Views & Parts List
Service Manual
8-4
Exploded Views & Parts List
0 3
6
4 5 8
(CLP-600N) 7
9
3
0
6
5
4
(CLP-600)
9
Service Manual
8-5
Exploded Views & Parts List
Service Manual
8-6
Exploded Views & Parts List
7
8
1
4
2
0
Service Manual
8-7
Exploded Views & Parts List
Service Manual
8-8
8
9 6 8
5
10
0 3 7
8.4. Right Cover
11
17
12
19 7 13
17 4
18 15 14
5
2-5
16
1
7
2-8 20
2-4 2-3
2-2
21
2-1
2-7 2-6
2-7
Service Manual
Exploded Views & Parts List
8-9
Exploded Views & Parts List
Service Manual
8-10
Exploded Views & Parts List
8
13
10
7
11
6
14
16
17
12
10
11
15
5
0
Service Manual
8-11
Exploded Views & Parts List
Service Manual
8-12
23-5
23
25 26 23-3
0 23-4
23-2
20 23-1
8.6. Main Frame
24 18
4 28
31
27
2 29 30
1
31
8-1
8 7
22
21
17
19 18 8-2
17-5 6
17-4
9
17-3
10
17-2
13
17-1 11
12
14-1
14
16
14-2
5
17
15-5
15-4
15-2 15
15-3
15-6
15-1
Service Manual
Exploded Views & Parts List
8-13
Exploded Views & Parts List
Service Manual
8-14
Exploded Views & Parts List
Service Manual
8-15
8-16
6
5
2 4
Service Manual
8.7. Fuser
0
14 10
1 13
8 9
Exploded Views & Parts List
12
16
7 15
3
17
28
8
9
11 8 9
17 18 26 27
24
30 32
23 9
25 9 29 31
26
22 19
21 49
20
8
9 34 38
23
35
40
41
30 33 47
32
44 42
45 50
39
31 46
52
36
37 44
43 42
41 51
54
53
48
54
Exploded Views & Parts List
Service Manual
8-17
Exploded Views & Parts List
Service Manual
8-18
Exploded Views & Parts List
40
0
3
4
3
35
2
13
34
15
33
15
15 16
38
16
17
14 27
15 11 10 39
20
16 16 28
7 21
20 18 14
13 14
8 14
17 12 9
22 13
14 12
10
16 35
23 13
19
16 14 34
29
28
24 33
29 30
32
1
25
31
26 9
14 36
36
37
37 9
9
Service Manual
8-19
Exploded Views & Parts List
Service Manual
8-20
6
8.9. MPF
0 5
3
14 4
2
3
11
12
7
26
25 27 8
13
9 10
26
29
28 16
17 23
36
19
15 22
37 30
32
38
35
14 20
19 21
31
33 34 24
18
Service Manual
Exploded Views & Parts List
8-21
Exploded Views & Parts List
Service Manual
8-22
3 1
4
8.10. Pick Up
0 5
16
4 3
6 14 13
9 5
8
7
16
5
10 17
12 18
19 20
11 5
11
21 10 8
22 15
23 40
24 33 34
35
25 31
27 24
26 32
28 36
29 25 27 37
30 S1
39
35
38
30
Service Manual
Exploded Views & Parts List
8-23
Exploded Views & Parts List
Service Manual
8-24
Exploded Views & Parts List
4
10
9
8
7
1
5
6
11
0
3
4
Service Manual
8-25
Exploded Views & Parts List
Service Manual
8-26
Exploded Views & Parts List
20
15
19
14
14
4
3
15
11
11
2
8
12
10
7
0
1
14
13
15
16
18
15
14
17
Service Manual
8-27
Exploded Views & Parts List
Service Manual
8-28
Exploded Views & Parts List
14
19
15
15
11
14
18
10
7
9
7
8
5
6
2
3
0
1
15
14
12
13
16
14
15
17
Service Manual
8-29
Exploded Views & Parts List
Service Manual
8-30
Exploded Views & Parts List
19
15 18
17
16
13
14
12
2
11
10
9 7
8 4
1
20 6
Service Manual
8-31
Exploded Views & Parts List
Service Manual
8-32
Exploded Views & Parts List
15
8
9
14
8
7
1
5
3
7
6
2
16
8
0
10
11
12
13
Service Manual
8-33
Exploded Views & Parts List
Service Manual
8-34
Exploded Views & Parts List
8
7
6
5
4
2
3
0
Service Manual
8-35
Exploded Views & Parts List
Service Manual
8-36
Exploded Views & Parts List
Service Manual
8-37
Exploded Views & Parts List
Service Manual
8-38
Exploded Views & Parts List
Service Manual
8-39
Exploded Views & Parts List
Service Manual
8-40
Block Diagram
9
9. Block Diagram
9.1 System Block Diagram
Service Manual
9-1
Samsung Electronics
Block Diagram
Service Manual
9-2
Samsung Electronics
Block Diagram
Service Manual
9-3
Samsung Electronics
Block Diagram
Service Manual
9-4
Samsung Electronics
Power(AC Input, 220/110V) Power Input
CON01
& Switch
CR 1 SMPS 3
CN28 CON71 CON51 CON51 CON52
SENSOR
RI GHT 2
Samsung Electronics
CN202 FUSER
Cover Switch
SUB board 10
CRUM 21 4 FUSER
BELT CN14 CN201 CON53 UNIT
I/F 5
C B CN8
CR drawer HVPS
6
SENSOR connector CON1 ATTR Paper Roller
LEFT
Engine& CN2
CN22 T1 CMYK T1 Roller
Video DEV CMYK DEV Roller
Controller Charger CMYK Charger Roller
(MAIN BD)rev 1.0 Supply CMYK Supply Roller
22
TEMP_OUT CN15
10. Connection Diagram
23 7 11 DEV K
TEMP_IN CN100 CN23
DEV YMC Driver Bd CN13 STEP MOTOR
BLDC MOTOR rev 1.4
24 12
TEMP_LSU CN204 CN12 Sensor(Exit)
8 13
25 OPC YMCK CN11 Sensor(Feed)
CN3
10.1 CLP-600/600N connection diagram
Service Manual
Connection Diagram
10-1
10-2
Cover S/W
Service Manual
Connection Diagram
Driver board
+
+24V_1 GND Motor & Clutch
RELAY
. Step motor(Fuser, Deve K)
+24V_2 +24VF_2 +24VF_2 . Pickup, MP Pickup, Fan1, Fan2
LPEC ASIC
10.2 Power distribution diagram
+24V_3
+24V_EN
On/Off HVPS board
+5V
LSU unit
+24VF_3
SCF option
SMPS Clutch
. 1 Clutch(Deve K)
Samsung Electronics
Connection Diagram
Service Manual
10-3
Samsung Electronics
Connection Diagram
Service Manual
10-4
Samsung Electronics
Connection Diagram
Service Manual
10-5
Samsung Electronics
Connection Diagram
Service Manual
10-6
Samsung Electronics
Connection Diagram
Service Manual
10-7
Samsung Electronics
Connection Diagram
Service Manual
10-8
Samsung Electronics
Connection Diagram
Service Manual
10-9
Samsung Electronics
Connection Diagram
Service Manual
10-10
Samsung Electronics
Connection Diagram
Service Manual
10-11
Samsung Electronics
Connection Diagram
Service Manual
10-12
Samsung Electronics
Connection Diagram
Service Manual
10-13
Samsung Electronics
Connection Diagram
Service Manual
10-14
Samsung Electronics
Connection Diagram
Service Manual
10-15
Samsung Electronics
Connection Diagram
Service Manual
10-16
Samsung Electronics
Connection Diagram
Service Manual
10-17
Samsung Electronics
Connection Diagram
Service Manual
10-18
Samsung Electronics
Connection Diagram
Service Manual
10-19
Samsung Electronics
Connection Diagram
Service Manual
10-20
Samsung Electronics
Connection Diagram
Service Manual
10-21
Samsung Electronics
Schematic Diagram
A A
Page Function
1 Index
B 2 Clock(ICS9248) & Power On Reset B
3 CPU ( RM5231A )
4 System Controller ( V320USC )
5 Aribiter PLD, Latch, 245
6 Memory ( Flash & SDRAM ), EEPROM
7 Panel UART
C
8 USB Controller ( ISP1582) C
10 HYPER-C
11 LPEC2
12 SCF, CRUM_DEVE
SAMSUNG
05.04.01
CLP-600
daVinci Main GDI
Rev 0.4
INDEX 1/21
Service Manual
11-1
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(2/21) Schematic Diagram
1 2 3 4 5 6 7 8
3.3V9248 75M_1
R165 75M_2
nCLKSTOP
R178
R163
DGND CLOCK SELECTION
+3.3V 3.3V9248 SDRCLK0
C123 Check 75MHz?
B B
SDRAMCLK0
R570
1 : DESKTOP MODE
NR53
FS1
VDDR
VDDSD
VDDSDR
VDDSDR2
VDDLCPU
VDDPCI1
VDDPCI0
+3.3V
CPUCLK3 FS2 NR25 NR24
CPUCLK2 PCLK_LAN
DGND
CPUCLK1 PCLK_WLAN
PCICLK_F
R180 PCLK_HYPERC
MODE PCICLK0
I_PCLK_WLAN R181 FS1 FS2
nCPUSTOP nCPUSTOP PCICLK1
I_PCLK_HYPERC R182
NR49 R297 R296
E8 nCLKSTOP nPCISTOP PCICLK2
I_PCLK_V320 R183
Check 3.3V nSDRSTOP nSDRSTOP PCICLK3
I_PCLK_PLD R184 PCLK_V320
nPD nPD PCICLK4
NR48
C
3.3V9248
NC3 NC4 NC5 NC8 C
nCPU25_33 SDRAM12
F6 R161 U33 E16 PCLK_PLD DGND DGND
Check 24MHz?
ELECTRONICS CO., LTD.
DGND ICS9248-81
SD_SEL SD_SEL SIO SIO +3.3V +3.3V
IOAPIC 48MHZ
C126 * Input only I2C VDDLAPIC 1205-002660 E14
ALL RIGHTS RESERVED
SDRAM2 NR26
SDRAM1 24MHZ
GND0
GND1
GND2
GND3
GND4
GND5
GND6
GNDL
9248_XOUT X2 SDRAM0
D
* Place NC5 very close to Hyper-C
DGND
9248_XIN
DGND
+3.3V +3.3V
E 9248_XOUT
nRESET
U41
DGND
Check High
nRESET
R249
C72
C208
05.04.01
CLP-600
Power On Reset daVinci MAIN GDI
Rev 0.4
ICS9248-81& RESET 2/21
Service Manual
11-2
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(3/21) Schematic Diagram
1 2 3 4 5 6 7 8
3.3VCCIO
CPU POWER
A C194 A
C204 C223 C211 C207 C203 C200 C224 C226 C219 C214 C206 C269
+3.3V 3.3VCCIO 1.8VCCINT 33uF
16V 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF
Check 1.8V?
E11
U44
F9
STS104B LD1117ADT18TR 1.8VCCINT
DGND
1 3 3 2
IN OUT
C248 IN OUT
C240 GND
16V GND 2 100nF 1
470uF
C250 C234 C218 C213 C215 C209 C146 C180 C150 C153 C141 C147 C152
33uF
C227 C197 C202 C228
100nF 16V
2.2uF 100nF 100nF 100nF 100nF 2.2uF 100nF 100nF 100nF 100nF 2.2uF 100nF 100nF 100nF 2.2uF
DGND
DGND
2401-000007
* Place 2.2uF all 4 side connected to 1.8VCCINT DGND
B B
3.3VCCIO
R229 * 1: Big Endian
* 0: LIttle Endian VCCOK
CPUCLK1
VCCOK
nCOLDRESET
nWARMRESET * from Hyper-C
Modeclock
ModeIn
C532
C533
C534
C535
C536
3.3VCCIO 1.8VCCINT
C C
DGND
ELECTRONICS CO., LTD.
VCCINT0
VCCINT1
VCCINT2
VCCINT3
VCCINT4
VCCINT5
VCCINT6
VCCINT7
VCCINT8
VCCINT9
VCCINT10
VCCINT11
SYSCLK
BENDIAN
PWRGD
CRST#
RST#
ALL RIGHTS RESERVED
JTDI
JTCK
AD(0) AD0 JTDO
AD(1) AD1 JTMS
AD(2) AD2
AD(3) AD3 MCLK
AD(4) RA50 3.3VCCIO
AD4 MODEIN
AD(5)
SAMSUNG
AD5
AD(6) AD6 ADC0
AD(7) AD7 ADC1 CMD(0:8)
AD(8) AD8 ADC2
AD(9) AD9 ADC3
AD(10) AD10
D AD(11) AD11
AD(12) AD12 CMD0 CMD(0)
AD(13) AD13 CMD1 CMD(1)
AD(14) AD14 CMD2 CMD(2)
AD(15)
AD(16)
AD15 U43 CMD3 CMD(3)
CMD(4) 3.3VCCIO
AD16 CMD4
AD(17) AD17 CMD5 CMD(5)
AD(18) AD18 CMD6 CMD(6)
AD(19)
AD(20)
AD19
AD20
RM5231A CMD7
CMD8
CMD(7)
CMD(8)
AD(21) RA53 R243 R230 R231 RA52 R240
AD21 CMDP
AD(22) AD22 R241
AD(23) AD23 DGND
AD(24) AD24 RDRDY#
AD(25) AD25 WRRDY# nWRRDY
AD(26) R503
AD26 VALIDIIN#
R502
nVALIDIN
AD(27) AD27 VALIDOUT# nVALIDOUT
AD(28) AD28 RELEASE# nRLS
AD(29) AD29 EXREQ#
E AD(30) AD30
AD(31) AD31
NM#
1.8VCCINT 1.8VCCP
E25 INT0# nINT_USB
INT1# nINT_LPEC
R242 INT2# nINT_HYPER
Check 1.8VCCP? INT3# nINT_LAN
VCCP
* DNCx : Do Not Connect INT4# nINT_WLAN
C233 C231 C232 INT5# 3.3VCCIO
DNC10
DNC11
DNC12
DNC13
R239
DNC0
DNC1
DNC2
DNC3
DNC4
DNC5
DNC6
DNC7
DNC8
DNC9
VSSP
NC10
NC11
NC12
NC13
NC14
NC15
NC16
GND
NC0
NC1
NC2
NC3
NC4
NC5
NC6
NC7
NC8
NC9
F
* VccP and VssP must be connected DGND
Service Manual
11-3
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(4/21) Schematic Diagram
1 2 3 4 5 6 7 8
3.3V320
*check PLL power
PAD(0:31)
VCC0
VCC1
VCC2
VCC3
VCC4
VCC5
VCC6
VCC7
VCC8
VCC9
VCC10
VCC11
PAD(31) AD(0:31)
AD31
A PAD(30) A
AD30
PAD(29) V_AD(31) RA155 AD(31)
AD29 SYSAD31
PAD(28) V_AD(30) AD(30)
AD28 SYSAD30
R202 PAD(16) PAD(27) V_AD(29) AD(29)
IDSEL_LAN PAD(26)
AD27 SYSAD29
V_AD(28) AD(28) +3.3V 3.3V320
AD26 SYSAD28
R203 PAD(17) PAD(25) V_AD(27) RA156 AD(27)
IDSEL_HYPER PAD(24)
AD25 SYSAD27
V_AD(26) AD(26) F7
AD24 SYSAD26
R204 PAD(18) PAD(23) V_AD(25) AD(25)
IDSEL_WLAN PAD(22)
AD23 SYSAD25
V_AD(24) AD(24)
AD22 SYSAD24
PAD(21) V_AD(23) RA157 AD(23)
E31 AD21 SYSAD23
PAD(1) PAD(20) V_AD(22) AD(22)
PAD(19)
AD20 SYSAD22
V_AD(21) AD(21) C139 C179 C178 C177 C176 C175 C258 C259 C262 C261 C260
AD19 SYSAD21
V_AD(20) AD(20) C132
PAD(18)
Check PAD(1) PAD(17)
AD18 SYSAD20
V_AD(19) RA158 AD(19)
AD17 SYSAD19
PAD(16) V_AD(18) AD(18)
AD16 SYSAD18
PAD(15) V_AD(17) AD(17)
AD15 SYSAD17
PAD(14) V_AD(16) AD(16) DGND
AD14 SYSAD16
PAD(13) V_AD(15) RA159 AD(15)
MIPS Interface
AD13 SYSAD15
PAD(12) V_AD(14) AD(14) DGND
AD12 SYSAD14
V_AD(13) AD(13)
PCI interface
B PAD(11) B
AD11 SYSAD13
PAD(10) V_AD(12) AD(12)
AD10 SYSAD12
PAD(9) V_AD(11) RA160 AD(11)
AD9 SYSAD11
3.3V320 PAD(8) V_AD(10) AD(10)
AD8 SYSAD10
PAD(7)
0 V_AD(9) AD(9)
AD7 SYSAD9
PAD(6)
1 V_AD(8) AD(8)
AD6 SYSAD8
PAD(5) V_AD(7) RA161 AD(7)
AD5 SYSAD7 E32
5.1K
5.1K
5.1K
5.1K
5.1K
5.1K
5.1K
5.1K
PAD(4) V_AD(6) AD(6) AD(27)
AD4 SYSAD6
PAD(3) V_AD(5) AD(5)
AD3 SYSAD5
PAD(2)
PAD(1)
AD2 SYSAD4
V_AD(4)
V_AD(3) RA162
AD(4)
AD(3)
Check AD(27)
AD1 SYSAD3
PAD(0) V_AD(2) AD(2)
R491
R490
R489
R224
R494
R493
R492
R495
AD0 SYSAD2
V_AD(1) AD(1)
SYSAD1
V_AD(0) AD(0)
nCBE(3) C_BE3 SYSAD0 CMD(0:8)
nCBE(2) C_BE2
nCBE(1) C_BE1
V_CMD(8) RA45 CMD(8)
nCBE(0) C_BE0 SCMND8
V_CMD(7) CMD(7)
SCMND7
V_CMD(6) CMD(6)
PAR PAR SCMND6
V_CMD(5) CMD(5)
C SCMND5 C
V_CMD(4) RA43 CMD(4)
nFRAME FRAME SCMND4
V_CMD(3) CMD(3)
Check 75MHz?
nTRDY TRDY SCMND3
V_CMD(2) CMD(2) CPUCLK2
ELECTRONICS CO., LTD.
R219
IDSEL
U36 VALIDOUT nVALIDOUT
nPERR DGND
PERR VALIDIIN
R501
nVALIDIN
nSERR SERR WRRDY nWRRDY
RELEASE nRLS
nREQ(0)
nGNT(0) 3.3V320
REQ
GNT
V320USC LCLK
RSTOUT
R175
R288
33
10
CPUCLK2
nPCI_RST
SAMSUNG
3.3V320 R176
NC1
V_MA(14) RA19 MA(14)
R201
NC2 MA14
V_MA(13) MA(13) MA(0:14)
MA13
R281 V_MA(12) RA35 MA(12)
MODE MA12
V_MA(11) MA(11) E33
MA(0)
MA11
V_MA(10) MA(10)
D INT0 MA10
INT1 MA9
V_MA(9)
V_MA(8) RA37
MA(9)
MA(8)
Check MA(0) +3.3V
INT2 MA8
V_MA(7) MA(7)
INT3 MA7 NR56
V_MA(6) MA(6)
MA6
PCLK_V320_delay V_MA(5) MA(5)
PCLK MA5
V_MA(4) RA40 MA(4)
nRESET RSTIN MA4
V_MA(3) MA(3)
MAD(0:31) MAD(31) RA147 V_MD(31) MA3
V_MA(2) MA(2) U181
MAD31 MA2 R583
MAD(30) V_MD(30) V_MA(1) MA(1)
MAD30 MA1
SDRAM interface
C159 MAD(29) V_MD(29) V_MA(0) MA(0)
MAD(28) V_MD(28) MAD29 MA0 PCLK_V320
E34 MAD(7) MAD(27) MAD28 nSDRAMCS
RA148 V_MD(27) C556
MAD(26) V_MD(26) MAD27 MCS0 PCLK_V320_delay
Check MAD(7) MAD(25) V_MD(25) MAD26 MCS1
MAD(24) V_MD(24) MAD25 MCS2 nSDRAMCS
DGND
MAD24 MCS3
MAD(23) RA149 V_MD(23) C557
V_MD(22) MAD23
MAD(22)
Local Data BUS
SCL_V320
GND0
GND1
GND2
GND3
GND4
GND5
GND6
GND7
GND8
GND9
SCL
nWRI nRD daVinci MAIN GDI
Rev 0.4
DGND V320 & BOOT ROM 4/21
Service Manual
11-4
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(5/21) Schematic Diagram
1 2 3 4 5 6 7 8
+3.3V
+3.3V
C106 C107
A A
nWR_ROM_FBIN
2
3
I_O_2 VCC_9
9
17
63mW
JTAG MAD(17) 13
D3
U27
Q3
12 A(17)
MA(3) 17
16
B1
B2
VCC
A1
2
3
A(6)
MA(2) A(5)
nWR_FBIN 6
I_O_3 VCC_17
29
D4 Q4
15
B3 A2
4
I_O_6 VCC_29 VCC MA(1) B4 A3 A(4)
8 41 MAD(16) 14 15 A(16) MA(0) 14 5 A(3)
nFRAME 10
I_O_8 VCC_41 D5 Q5
13
B5 A4
6
BE
B A(2) B
11
I_O_10
4 E24 MAD(15) 17 16 A(15)
DQM3 12
B6 A5
7
BE 12
I_O_11 GND_4
16
GND1 D6 Q6 DQM1 11
B7 A6
8 A(1)
13
I_O_12 GND_16
24
GND2
MAD(14) 18 19 A(14)
DQM0 B8 A7
9 A(0)
nROMCS 14
I_O_13 GND_24
36
TP840 +3.3V
D7 Q7 A8
nWRi 15
I_O_14 GND_36 TP841
11 1 10 19
18
I_O_15
1
TP842 ALE LE _OE GND _G
1
nGNT(4) 20
I_O_18 I_O_TDI
7
TDI Check ALE? GND DIR
nWR_ROM_FBOUT 21
I_O_20 U101 TMS_I_O
26
TMS R210 74LCX373MTC 10
I_O_21 I_O_TCK TCK 10K C74LCX245FT-ELP
22 32
nREQ(1) 23
I_O_22 ATF1502ASV I_O_TDO TDO
DGND 0801-002095
nREQ(0) 25
I_O_23
39
I_O_25 GCLR_I nPCI_RST
27 37 DGND
R500 28
I_O_27 GCLK1_I
35
PCLK_PLD +3.3V
245
DGND
nWR 30
I_O_28 GCLK2_OE2_I
40
nGNT(2) C196
nWR_ROM 31
I_O_30 GCLK3_I_O
1nF
nWR_FBOUT 33
I_O_31
38
nGNT(0) 34
I_O_33 I_OE1
nGNT(1) 42
I_O_34
5 C89 C90
nWR nREQ(2) 43
I_O_42 PD1_I_O
19
nIRDY DGND
C nREQ(4) 44
I_O_43 PD2_I_O nGNT(3) C
nREQ(3) I_O_44
ELECTRONICS CO., LTD.
MAD(13) 3 VCC 2
D0 Q0 A(13)
No REQ,GNT MAD(12) 4 5 A(12)
RA49 R205 RA46 R209 D1 Q1
0 V320 10K
10K 10K
10K MAD(11) 7 6 A(11)
63mW 63mW
D2 Q2
1 Hyper MAD(10)
SAMSUNG
8 9 A(10)
D3 Q3
2 LAN nGNT(0) nREQ(0) MAD(9) 13
U21
12 A(9)
nGNT(1) nREQ(1) D4 Q4
3 WLAN nGNT(2) nREQ(2) MAD(8) 14 15 A(8)
nGNT(3) nREQ(4) D5 Q5
D 4 Reserved nGNT(4) nREQ(3) MAD(7) 17 16 A(7)
nWR_ROM_FBIN D6 Q6
MAD(31) 18 19
D7 Q7
nWR_ROM_FBOUT
10 R289
nWR_ROM_FBIN ALE
11
LE _OE
1 nFLASH_OE
GND
10 R290
nWR_FBOUT nWR_FBIN 74LCX373MTC 10
C283 C284
10pF 10pF
DGND
DGND DGND
E
LATCH
05.04.01
CLP-600
daVinci main GDI
Rev 0.4
Latch&PLD 5/21
Service Manual
11-5
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(6/21) Schematic Diagram
1 2 3 4 5 6 7 8
MA(0:12)
A A
MAD(0:31)
U24
MA(12) 36 53 MAD(15)
A12 DQ15
MA(11) 35 51 MAD(14)
A(0:21) MA(10)
A11 DQ14
MAD(13)
22 50
A10 DQ13
A(20) MA(9) 34 48 MAD(12)
A(19)
A(0) MA(8)
A9 DQ12
MAD(11)
33 47
A8 DQ11
A(18) MA(7) 32 45 MAD(10)
A7 DQ10
A(17) MA(6) 31 44 MAD(9)
A6 DQ9
A(16) MA(5) 30 42 MAD(8)
A5 DQ8
A(15) MA(4) 29 13 MAD(7)
A(14)
MAD(0:7)
MA(3) 26
A4
A3
DQ7
DQ6
11 MAD(6) *Change RAM size to 32MB before Mass Production
A(13) MA(2) 25 10 MAD(5)
A2 DQ5
A(12) MAD(7) MA(1) 24 8 MAD(4)
A1 DQ4
A(11) MAD(6) MA(0) 23 7 MAD(3)
A0 DQ3
A(10) MAD(5) 5 MAD(2)
B DQ2
A(9) MAD(4) 4 MAD(1) B
DQ1
A(8) MAD(3) 40 2 MAD(0)
MA_13 NC/RFU DQ0
A(7) MAD(2) +3.3V
A(6) MAD(1)
A(5) MAD(0) R498 18 +3.3V
A(4)
nRAS R499
*RAS
17
A(3)
nCAS *CAS
1
VDD1
A(2) 14
VDD2
A(1) 20 27
R59 MA(13) BA0 VDD3 C256 C165 C164 C257
21 3
C57 MA(14) BA1 VDDQ1
VDDQ2
9 U170
DGND R152 19 43
A(21) nSDRAMCS R497
*CS VDDQ3
16 49
nSDRAMWE *WE VDDQ4
DGND 15 28
DQM0 LDQM VSS1
39 41
D13 DQM1 UDQM VSS2
nROMCS 54
VSS3 C161 C163 C162
R111 6
nFLASH_OE DQM0 VSSQ1
12
nWR_ROM nRESET VSSQ2
C 38 46 C
R211 SDRCLK0 CLK VSSQ3
37 52
* for BTS Jig control CLKE CKE VSSQ4
ELECTRONICS CO., LTD.
K4S561632B-TC1L DGND
DIP socket
Flash
ALL RIGHTS RESERVED
+3.3V
DGND
CN13-8
U23
SDA_V320 5 4
* 1107-001286 : AM29LV160D 16Mb for world wide(Default) +3.3V
MA(12) 36 53 MAD(31)
6 3
SAMSUNG
R144 MA(11)
A12 DQ15
MAD(30) SCL_V320
35 51 NR42
* 1107-001475 : M29DW323DB 32Mb for Korea Market only CLKE
MA(10)
MA(9)
22
34
A11
A10
DQ14
DQ13
50
48
MAD(29)
MAD(28)
+3.3V
7 2
A9 DQ12
MA(8) 33 47 MAD(27)
MA(7)
A8 DQ11
MAD(26)
8 1
32 45
C98 MA(6)
A7 DQ10
MAD(25)
D 31 44
A6 DQ9 C117
MA(5) 30 42 MAD(24)
A5 DQ8
MA(4) 29 13 MAD(23) DGND
A4 DQ7
MA(3) 26 11 MAD(22) DGND
A3 DQ6
DGND MA(2) 25 10 MAD(21)
A2 DQ5
MA(1) 24 8 MAD(20)
A1 DQ4
MA(0) 23 7 MAD(19) DGND
A0 DQ3
5 MAD(18)
DQ2
4 MAD(17)
DQ1
40 2 MAD(16)
NC/RFU DQ0
18
17
*RAS
*CAS
+3.3V EEPROM
1
VDD1
14
VDD2
20 27
MA(13) BA0 VDD3 C253 C254 C255 C171
21 3
MA(14) BA1 VDDQ1
9
VDDQ2
19 43
E *CS VDDQ3
16 49
*WE VDDQ4
15 28
DQM2 LDQM VSS1
39 41
DQM3 UDQM VSS2
54
VSS3 C252 C158 C170
6
VSSQ1
12
VSSQ2
38 46
SDRCLK0 CLK VSSQ3
37 52
CLKE CKE VSSQ4
K4S561632B-TC1L DGND
1105-001384
05.04.01
F SDRAM
CLP-600
daVinci MAIN GDI
Rev 0.4
Memory 6/21
Service Manual
11-6
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(7/21) Schematic Diagram
1 2 3 4 5 6 7 8
A A
+5V
NR54
PANEL C558
TX0 from Hyper-c
R584
B E3
Check Logic High?
LPEC2_TX from LPEC2 B
CN9-1
35303-0550 DGND
+3.3V
1
2
L7
3
L8 R535
4 nRST_PANEL
5 RX_IN
L10
R532
L6 R533
C42 C45 C48
R539
Q23
Q22
RX0 To Hyper-c
R538 NR55
DGND RX_IN NR43
C C
*for davinci network Model R534
C511
LPEC2_RX To LPEC2
ELECTRONICS CO., LTD.
ALL RIGHTS RESERVED
DGND
SAMSUNG
D
+5V
C41
CN21-1
L4
L27
R298
RX2
L3
R299
L28 TX2
C328
E
C327
FGND
DGND
DGND
DEBUG CONN
05.04.01
CLP-600
daVinci MAIN GDI
Rev 0.4
UART 7/21
Service Manual
11-7
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(8/21) Schematic Diagram
1 2 3 4 5 6 7 8
C116 C115
L24
RA54
MAD(0:15) U_MAD(0:15)
MAD(15) U_MAD(15)
DGND MAD(14) U_MAD(14)
AGND_USB MAD(13) U_MAD(13)
MAD(12) U_MAD(12)
MAD(11) U_MAD(11)
MAD(10) U_MAD(10)
MAD(9) RA55 U_MAD(9)
B MAD(8) U_MAD(8) B
RA137
MAD(7) U_MAD(7)
MAD(6) U_MAD(6)
C323
MAD(5) U_MAD(5)
100nF
+3.3V USB_3.3VA MAD(4) U_MAD(4)
MAD(3) U_MAD(3)
MAD(2) U_MAD(2)
MAD(1) RA138 U_MAD(1)
DGND MAD(0) U_MAD(0)
U_MAD(0:15)
21
34
48
53
54
28
50
A(9:2) DGND
Vcc_I_O_21
Vcc_I_O_34
Vcc_I_O_48
Vcc_53
Vcc_54
Vcc_1V8_28
Vcc_1V8_50
ALL RIGHTS RESERVED
A(2) 18
A0
A(3) 19 30 U_MAD(0)
A1 DATA0
A(4) 20 31 U_MAD(1)
A2 DATA1
+3.3V A(5) 22 32 U_MAD(2)
A3 DATA2
+3.3V A(6) 23 33 U_MAD(3)
A4 DATA3
A(7) 24 35 U_MAD(4)
A(8) 25
A5 DATA4
36 U_MAD(5) USB_CONN
SAMSUNG
A6 DATA5
RA57 A(9) 27 37 U_MAD(6)
A7 DATA6
R301 38 U_MAD(7) CN20-1
R147 DATA7
9 39 U_MAD(8)
DREQ DATA8 787780-1
10 40 U_MAD(9)
DACK DATA9
E4 DGND 42 U_MAD(10)
DATA10
D 7 43 U_MAD(11) +3.3V 1
nPCI_RST RESET_N DATA11
Check High? DATA12
44 U_MAD(12)
L31 VBUS
8
EOT U120 DATA13
45 U_MAD(13)
42ohm NL1
C50 ISP1582BS 46 U_MAD(14) 2
DATA14
11
DIOR DATA15
47 U_MAD(15)
R330 1 4 D-
12
DIOW 1.5K N.C
2
RPU
15 3 2 3 3
nUSB_CS nCS DP
DM
4
INSTPAR
D+
DGND 16
nRD 17
nRD
49 R339 200K
nWR nWR VBUS L30
42ohm
C111 R332 100 14 6 4
nINT_USB INT RREF
R329 C302 C300 AGND
52 55
XTAL1 WAKEUP 1M 1uF 2.2uF
51 56 5
DGND_13
DGND_26
DGND_29
DGND_41
XTAL2 SUSPEND
FGND
AGND_1
AGND_5
TGND
R302 R331
R160 OSC2
10K 12K 6
E
XIN_USB
1% FGND
1
5
13
26
29
41
57
C112
DGND FGND
DGND 3722-001101
2203-000476|R2012_CAP
DGND
AGND_USB DGND cf) 2.2uF,2012, 2203-001598
DGND
05.04.01
CLP-600
daVinci MAIN GDI
Rev 0.4
USB 8/21
Service Manual
11-8
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(9/21) Schematic Diagram
1 2 3 4 5 6 7 8
+3.3V 3.3_NPC
L22
A A
C142 C148 C562
47uF(MLCC)
+3.3V
CN25-39
LGND
179029-3 R197
E1
R592 40 80
nINT_LAN Check Logic High?
39 79 R596
nPCI_RST
E2 C160
38 78
32 R599
72 IDSEL_WLAN
PAD(27) PAD(28)
31
71
PAD(25) PAD(26)
30 70
29 69
R595 PAD(24)
C
nCBE(3) 28 68
C
PAD(23)
27 67
PAD(22)
ELECTRONICS CO., LTD.
26 66
PAD(21) PAD(20)
25 65
ALL RIGHTS RESERVED
PAD(19) 24 64
PAD(18)
23 63 * Reserved
RA170 PAD(17)
22 62 nNPC_RST
RA172
PAD(16)
SAMSUNG
nCBE(2) 21 61 C201
nIRDY 20 60 nFRAME
nDEVSEL 19 59 nGNT(3)
D DGND
IDSEL_LAN 18 58 nTRDY
RA171
17 57 nSTOP
nPERR 16 56
nSERR 15 55
14 R600
54 PAR
13 PAD(15)
nCBE(1) 53
PAD(14) 12 52
11 PAD(13)
51
PAD(12) PAD(11)
10
50
PAD(10) 9
49
E
8 PAD(9)
48
PAD(8) R601
7 47 nCBE(0)
PAD(7) R602
6 46 nREQ(3)
+3.3V 45
PAD(6)
5
PAD(5) 44 PAD(4)
4
DGND
NPC CLP-600
daVinci MAIN GDI
LGND DGND Rev 0.4
PCI Network 9/21
Service Manual
11-9
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(10/21) Schematic Diagram
1 2 3 4 5 6 7 8
+3.3V
L34
+1.8V_HYPERC
1uH
C539 C538
A +1.8V_HYPERC A
+3.3V +3.3V U129
104
117
139
146
160
173
183
209
211
221
223
231
239
253
204
125
129
133
151
157
164
169
178
188
192
195
215
246
F11
10
26
41
57
71
87
16
49
79
96
STS104B LD1117ADT18TR
1.8V_VDD0
1.8V_VDD1
1.8V_VDD2
1.8V_VDD3
1.8V_VDD4
1.8V_VDD5
1.8V_VDD6
1.8V_VDD7
1.8V_VDD8
1.8V_VDD9
1.8V_VDD10
1.8V_VDD11
1.8V_VDD12
1.8V_VDD13
1.8V_VDD14
1.8V_VDD15
1.8V_VDD16
1.8V_VDD17
1.8V_VDD18
1.8V_VDD19
1.8V_PLL
3.3V_VDD0
3.3V_VDD1
3.3V_VDD2
3.3V_VDD3
3.3V_VDD4
3.3V_VDD5
3.3V_VDD6
3.3V_VDD7
3.3V_VDD8
3.3V_VDD9
3.3V_VDD10
3.3V_VDD11
3.3V_VDD12
3.3V_VDD13
3.3V_VDD14
3.3V_VDD15
3.3V_VDD16
AGND 1 3 3 2
IN OUT
248 OUT
GPIO0 RA134 8 6 4 2 C453 C494 IN
249 GND
GPIO1 100uF C454
250 63mW GND 1
GPIO2 16V 2 33uF
251 10K +3.3V
GPIO3 16V
252 7 5 3 1 100nF
DGND GPIO4 TANTAL
255
GPIO5
256 64 R484 33 DGND 2404-001102
GPIO6 MIPS_INIT05
1 63 NR29 0 DGND
GPIO7 MIPS_INIT06
2 62
GPIO8 MIPS_INIT07
3 61 R485 33
GPIO9 MIPS_INIT08
4 60 NR30 0
GPIO10 MIPS_INIT09
5
6
GPIO11
GPIO12
U131-2 MIPS_INIT10
MIPS_INIT13
59
56 NR34 33
+1.8V_HYPERC
7 55 R475 0
GPIO13 MIPS_INIT14
8 54
B
9
GPIO14
HIPERC MIPS_INIT20
53 R486 33
B
C474
C475
C476
C477
C478
C479
C480
C481
C482
C483
C484
C485
C486
C487
C488
C489
C490
C491
C492
C495
GPIO15 MIPS_INIT21
12 52 NR31 0
GPIO16 MIPS_INIT24
R481 22 13 51
Debugger_RX2 RX2 GPIO17 MIPS_INIT25
237 50 R487 33
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
GPO0 MIPS_INIT26
238 NR32 0
GPO1
241
GPO2
242 R488 33
GPO3
243 NR33 0
GPO4
R483 22 244 DGND +3.3V
GND_PLL
Debugger_TX2 TX2 GPO5
DGND
GND10
GND11
GND12
GND13
GND14
GND15
GND16
GND17
GND18
GND19
GND20
GND21
GND22
GND23
GND24
GND25
GND26
GND27
GND28
GND29
GND30
GND31
GND32
GND33
GND34
GND35
GND36
GND0
GND1
GND2
GND3
GND4
GND5
GND6
GND7
GND8
GND9
DGND
C457
C458
C459
C460
C461
C462
C463
C464
C465
C466
C467
C468
C469
C470
C471
C472
C473
11
17
27
42
48
58
72
78
80
88
97
105
118
126
134
140
145
147
152
161
165
172
174
179
184
189
196
210
212
216
222
224
232
240
245
247
254
205
L33
1uH
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
DGND DGND
AGND AGND +3.3V
C C
+3.3V
PAD(0:31)
DGND
ELECTRONICS CO., LTD.
PAD(0)
PAD(1)
PAD(2)
PAD(3)
PAD(4)
PAD(5)
PAD(6)
PAD(7)
PAD(8)
PAD(9)
PAD(10)
PAD(11)
PAD(12)
PAD(13)
PAD(14)
PAD(15)
PAD(16)
PAD(17)
PAD(18)
PAD(19)
PAD(20)
PAD(21)
PAD(22)
PAD(23)
PAD(24)
PAD(25)
PAD(26)
PAD(27)
PAD(28)
PAD(29)
PAD(30)
PAD(31)
+3.3V RA136
ALL RIGHTS RESERVED
10K
2 8 6 4 63mW +5V +3.3V
200
199
198
197
194
193
191
190
186
185
182
181
180
177
176
175
154
153
150
149
148
144
143
142
137
136
135
132
131
130
128
127
RA135
DGND
63mW
10K
PCIAD0
PCIAD1
PCIAD2
PCIAD3
PCIAD4
PCIAD5
PCIAD6
PCIAD7
PCIAD8
PCIAD9
PCIAD10
PCIAD11
PCIAD12
PCIAD13
PCIAD14
PCIAD15
PCIAD16
PCIAD17
PCIAD18
PCIAD19
PCIAD20
PCIAD21
PCIAD22
PCIAD23
PCIAD24
PCIAD25
PCIAD26
PCIAD27
PCIAD28
PCIAD29
PCIAD30
PCIAD31
R170 1 7 5 3
10K 121 34
PCICLKRUN nSTROBE nSTROBE CN1-1 TP837
202 35
R571 PCLK_HYPERC
201
PCICLK nINIT
36
nINIT PD(0:7) PD(0:7)
nPCI_RST PCIRST nAUTOFD nAUTOFD
SAMSUNG
123 37
nGNT(1) PCIGNT nSELECTIN nSELECTIN 2 1
124 28
C88 nREQ(1)
170
PCIREQ BUSY
29
BUSY
1nF PAR PCIPAR PERROR PERROR PD(0)
4 3 PD(1)
122 30
158
PCIPME SLCT_OUT
31
SLCT_OUT PD(0:7)
nIRDY PCIIRDY FAULT nFAULT PD(2)
6 5 PD(3)
159 32
D nTRDY
166
PCITRDY PDE
33
PDE
PCILOCK nACK nACK PD(4)
8 7 PD(5)
DGND 163 47 PD(0)
nSTOP PCISTOP PDATA0 nHSYNC
167 46
nPERR PCIPERR PDATA1 PD(1) PD(6)
10 9 PD(7)
168 45 PD(2)
nSERR PCISERR PDATA2
156 44 33 NR35
nFRAME PCIFRAME PDATA3 PD(3)
nACK 12 11 BUSY
162 43 PD(4) 33 NR36
nCBE(0:3) nDEVSEL PCIDEVSEL PDATA4
141 40 33 NR37
IDSEL_HYPER PCIIDSEL PDATA5 PD(5)
nFAULT 14 13 SLCT_OUT
nCBE(0) 187 39 PD(6) 33 NR38
PCICBE0 PDATA6
nCBE(1) 171 38
PCICBE1 PDATA7 PD(7)
nHSYNC PERROR 16 15 nAUTOFD
nCBE(2) 155 219
PCICBE2 nHSYNC1 nLSYNC_1
nCBE(3) 138
65
PCICBE3 U131-1 nHSYNC2
220
225
nLSYNC_2 nSELECTIN 18 17 nINIT
ModeClock MIPS_ModeClock nHSYNC3 nLSYNC_3
66 226
ModeIn MIPS_Mode_In nHSYNC4 nLSYNC_4 nSTROBE 20 19 PDE
67 227
nWARMRESET MIPS_WarmReset nFSYNC1 nPSYNC_1 PDE
nCOLDRESET
68
69
MIPS_ColdReset HIPERC nFSYNC2
228
229
nPSYNC_2 22 21
VccOK MIPS_VccOK nFSYNC3 nPSYNC_3
70 230
24MHZ MIPS_SysClk nFSYNC4 nPSYNC_4 24 23
25 233
OM0 VCLK_C VCLK_1
24 234
E OM1 VCLK_M VCLK_2 26 25
23 235
OM2 VCLK_Y VCLK_3
206 236
nINT_HYPER IRQ0 VCLK_K VCLK_4 28 27
207 203 NR39 33
IRQ1 MPLLCAP LPEC2_CLK
208 213 RA167
nPCI_RST nRESET VDO1 nVDI_1
14 214
Panel_TX0 TX0 TxD0 VDO2 nVDI_2
15 217
Panel_RX0 RX0 RxD0 VDO3 nVDI_3 DGND
99 218
nCAS VDO4 nVDI_4
+3.3V 100 18
nRAS TDO
101 19 DGND
nSCS TDI
98 20
R586 nWEN TMS
95 21
SCLK TCK
94 22
SCLK_EN nTRST
63mW
RA133 2 4 6 8 10K
SD10
SD11
SD12
SD13
SD14
SD15
SA10
SA11
SA12
SD0
SD1
SD2
SD3
SD4
SD5
SD6
SD7
SD8
SD9
BA0
BA1
SA0
SA1
SA2
SA3
SA4
SA5
SA6
SA7
SA8
SA9
nLSYNC_1
RA163 nLSYNC_2 05.04.01
102
103
120
119
116
115
114
113
112
111
110
109
108
107
106
93
92
91
90
89
86
85
84
83
82
81
77
76
75
74
73
1 3 5 7 C456 2 4 6 8
C455 nLSYNC_3
1nF nLSYNC_4
F 220pF 1 3 5 7
DGND
63mW C517 C516 C515 C514
10K CLP-600
AGND
daVinci MAIN GDI
DGND
Rev 0.4
DGND
HYPER-C 10/21
Service Manual
11-10
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(11/21) Schematic Diagram
1 2 3 4 5 6 7 8
nS_5V_OFF nLSYNC_4
nS_NEW_FUSER nLSYNC_3
RDY_SCF nLSYNC_2
nS_ACR_2 nLSYNC_1
nS_ACR_1 VCLK_4
SCL_DEV VCLK_3
SDA_DEV VCLK_2
SCL_BELT VCLK_1
SDA_BELT nVDI_4
A CLK_SCF nVDI_3
nVDI_2
+3.3V LPEC2_TX nVDI_1 +5V
LPEC2_RX nPSYNC_4 +2.5V
CMD_SCF nPSYNC_3 U14 F5
R569 STS_SCF nPSYNC_2 A
R568 nPSYNC_1
B B
R582 R128 R542
DGND_RING R512 R543 +2.5VA
DAO
VDDA_DAC
VSSA_DAC
INT_OUT
GPIOC6|ZERO_CROSS
GPIOE7|FUSER1_ON
GPIOE6|FUSER0_ON
GPIOE5|USART2_RXD
GPIOE4|USART2_TXD
GPIOE3|USART1_RXD
GPIOE2|USART1_TXD
GPIOE1|USART0_RXD
GPIOE0|USART0_TXD
VSSO7
VDDO7
GPIOD6|USART2_CLK
GPIOD5|USART1_CLK
GPIOD4|USART0_CLK
GPIOD3|IIC1_SDA
GPIOD2|IIC1_SCL
GPIOD1|IIC0_SDA
GPIOD0|IIC0_SCL
GPIOC5|ACR_RIGHT
GPIOC4|ACR_LEFT
GPIOC3|nVDI_CON_DB_4TH
GPIOC2|nVDI_CON_DB_3RD
GPIOC1|nVDI_CON_DB_2ND
GPIOC0|nVDI_CON_DB_1ST
VSSI6
VDDI6
GPIOB7|nLSYNC_4TH
GPIOB6|nLSYNC_3RD
GPIOB5|nLSYNC_2ND
GPIOB4|nLSYNC_1ST
GPIOB3|VCLK_4TH
GPIOB2|VCLK_3RD
GPIOB1|VCLK_2ND
GPIOB0|VCLK_1ST
nVDI_4TH
nVDI_3RD
nVDI_2ND
nVDI_1ST
VSSO6
VDDO6
nPSYNC4
nPSYNC3
nPSYNC2
nPSYNC1
VSS_R
VDD_R
nSH_LSU_DB_4
nSH_LSU_DB_3
A_MUX1 F4
A(6)
ADDR5 nVDO_LSU_4TH nVDO_4
DGND
A(5)
ADDR4 nVDO_LSU_3RD nVDO_3
A(4)
ADDR3 nVDO_LSU_2ND nVDO_2
DGND
ALL RIGHTS RESERVED
A(3)
ADDR2 nVDO_LSU_1ST nVDO_1
A(2)
ADDR1 GPIO87|nSTART_LSU_4TH nSTART_LSU_4
ADDR0 U19 GPIO86|nSTART_LSU_3RD STS_IH2
DGND
VDDO0 GPIO85|nSTART_LSU_2ND STS_IH1
U_MAD(0:7) U_MAD(7)
VSSO0 GPIO84|nSTART_LSU_1ST STS_IH0
U_MAD(6)
U_MAD(5)
DATA7
DATA6 LPEC2 GPIO83|nLDON_LSU_4TH
GPIO82|nLDON_LSU_3RD
nLDON_LSU_4
nBLDC_RDY2
U_MAD(4)
DATA5 GPIO81|nLDON_LSU_2ND nBLDC_RDY1
DATA4 GPIO80|nLDON_LSU_1ST nLDON_LSU_1
SAMSUNG
U_MAD(3)
U_MAD(2)
DATA3 JC13-00029A nHSYNC_4TH nHSYNC
DATA2 nHSYNC_3RD
U_MAD(1)
DATA1 nHSYNC_2ND
U_MAD(0) +3.3V
DATA0 nHSYNC_1ST
nS_EMPT GPIO00|PWM32 VSSO4
S_MP_EMPT GPIO01|PWM33
GPIO24|EXT_C4
GPIO25|EXT_C5
GPIO26|EXT_C6
GPIO27|EXT_C7
GPIO32|PWM10
GPIO33|PWM11
GPIO34|PWM12
GPIO35|PWM13
GPIO36|PWM14
GPIO37|PWM15
GPIO40|PWM16
GPIO41|PWM17
GPIO42|PWM18
GPIO43|PWM19
GPIO44|PWM20
GPIO45|PWM21
GPIO46|PWM22
GPIO47|PWM23
GPIO50|PWM24
GPIO51|PWM25
GPIO52|PWM26
GPIO53|PWM27
GPIO54|PWM28
GPIO55|PWM29
GPIO56|PWM30
GPIO57|PWM31
GPIO60|PWM31
nCUT_FUSER GPIO17|M5_nB GPIO62|MOT0_B SM_YM_B
GPIO30|PWM8
GPIO31|PWM9
GPIO61|M_nA
+3.3V
VDDO1
VDDO2
VDDO3
VSSO1
VSSO2
VSSO3
PWM0
PWM1
PWM2
PWM3
PWM4
PWM5
PWM6
PWM7
VDDI2
VDDI3
VSSI2
VSSI3
R127
RA4
RA7 DGND DGND_RING C85 C84 C83 C82 C81
GNDA DGND +3.3V
DGND DGND
Service Manual
11-11
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(12/21) Schematic Diagram
1 2 3 4 5 6 7 8
A A
+3.3V
+3.3V +24V
[ SCF ]
CN26-1
C229
B STS_SCF B
U46-2
CN26-3
R247
DGND
CMD_SCF
U46-3
CN26-4
R248
CN26-5 U46-4
R252
RDY_SCF
C C
CN26-6
ELECTRONICS CO., LTD.
NR47 Q15
CN26-7
C230 C225
Q31 R340
NDT2955 CLK_SCF
4
DGND 3 D2
S
SAMSUNG
2
CN26-8 D1
R590 1 G
DGND
DGND
+3.3V_CRUM
D Q26
CN26-9 FGND
[CRUM_DEVE]
+3.3V_CRUM
+3.3V_CRUM
C554
SCL_S0
SCL_S1
DGND
05.04.01
F
DGND
CLP-600
daVinci MAIN GDI
Rev 0.4
SCF & CRUM IF 12/21
Service Manual
11-12
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(13/21) Schematic Diagram
1 2 3 4 5 6 7 8
A A
B B
DGND
DGND
DGND
*Check CL !!!
OSC3
C113 C103
+3.3V
U32
31.005MHz
C C
C325 C324
ELECTRONICS CO., LTD.
NR17 NR18
ALL RIGHTS RESERVED
DGND
CLK_VIDEO
SAMSUNG
+3.3V +3.3V
NC28 NC29
D
DGND
*Reserved NRA1
nSH_LSU_4
RA15
nHEATER_FUSER
+3.3V nSH_LSU_3 CMD_SCF
DGND DGND
nSH_LSU_2
nSH_LSU_1 CLK_SCF
NR21
nSOL_PICKUP CLK_LSU_4
nSOL_MP
nSOL_DUP
RA3 +3.3V +3.3V
+3.3V
PWM_CHARGER R132
+3.3V R131
PWM_ATTR+ STS_IH0
R79 STS_IH1
nRST_PANEL STS_IH2
NR13 nENB_DEVE_AC_1 RA58
nPRT_REQ nENB_DEVE_AC_2
nENB_DEVE_AC_3 R129 STS_SCF
NR6
BLDC_CLOCK2 nENB_DEVE_AC_4 05.04.01
NRA4 RA164
nLSYNC_4
F
PWM_CR_2 R304 nLSYNC_3
nFAN_FUSER PWM_CR_1 R305 nLSYNC_2
nFAN_SMPS nLSYNC_1
CLP-600
RA13
DGND daVinci MAIN GDI
Rev 0.4
RESET & CLOCK 13/21
Service Manual
11-13
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(14/21) Schematic Diagram
1 2 3 4 5 6 7 8
[LSU]
+5VL
A +5VL +5VL A
CN3-1
C6
R6
DGND
Reserved Reserved
VDO_4+ nLDON_LSU_4
U1-1
NC11 NC22 +5VL +5VL
DGND
DGND R22 R21
DGND U1-3
B VDO_4- nSH_LSU_4 B
NC10 NC18
DGND DGND
VDO_3+ DA_POWER
NC12
C314 C301
DGND DGND
VDO_3- nSH_LSU_3
U1-4
NC19
NC13
+5VL
C DGND C
DGND R508
ELECTRONICS CO., LTD.
VDO_2+ nLDON_LSU_1
+3.3V
ALL RIGHTS RESERVED
NC14 U1-2
+5VL
LVDS
C29 C27
DGND R24 U1-5
SAMSUNG
NC20
VDO_1+
nVDO_1 VDO_1-
D VDO_1+ DGND +5VL nVDO_2 VDO_2-
VDO_2+
NC16 VDO_3+
DGND nVDO_3 VDO_3-
nVDO_4 VDO_4-
R11 U1-6 VDO_4+
DGND
VDO_1- nSH_LSU_1
+5VL +3.3V
NC17 NC23
DGND
E
Spacing : 8 mils
DGND
U10-1
R52
R57
DGND
R70 GND seperation : 10 mils
R49 R53
CLK_LSU_4 nRDY_LSU_4
C38
U10-2
C39
+5V
DGND
DGND
DGND
R56 DGND
R50
nSTART_LSU_4
+24VF
FGND
05.04.01
U10-3
F C36
DGND
CLP-600
FGND
daVinci MAIN GDI
Rev 0.4
LSU 14/21
Service Manual
11-14
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(15/21) Schematic Diagram
1 2 3 4 5 6 7 8
A DGND3 DGND1 A
5 4 1 2
FGND R591
PWM_AC_1 R589
PWM_AC_VPP_1 C561
PWM_DEVE_DC_1 C531
nENB_DEVE_AC_1
+24V +5V
24V2 R588
COVER_CLOSED
B Check 24V? RA61
DGND
DGND
B
R544 Q29
C287 PWM_AC_2
C305
PWM_AC_VPP_2
PWM_DEVE_DC_2 DGND
nENB_DEVE_AC_2
R557
FGND nS_5V_OFF
RA62
Q27
+24V
PWM_AC_3
PWM_AC_VPP_3
PWM_DEVE_DC_3
nENB_DEVE_AC_3 DGND
C C
ELECTRONICS CO., LTD.
[COVER SW]
ALL RIGHTS RESERVED
R365
FGND PWM_AC_4 +24V +24VF +3.3V
+5V R366 CN202-1
5V
Check 5V? PWM_AC_VPP_4
Check 24VF?
24VF
SAMSUNG
C246 C243
[HVPS 2]
D CN22-1 R363
C251 C249 NC33 NC34 NC30 NC32 NC35 NC31
PWM_DEVE_DC_4
R364 330UF 100nF 1000uF 330UF 100nF 1000uF
DGND
6.3V 16V 6.3V 16V
nENB_DEVE_AC_4
+5V
FGND DGND
C330 RA64
DGND
DGND
+24VF
PWM_CHARGER
PWM_T_2
U10-5 PWM_T_1
n24V_EN_OUT
L36
C551 C545 C546 C547 C548 C549 C550
E
RA63
n24V_EN
PWM_T_4
C326
PWM_T_3
nENB_ATTR- +24VF +3.3V
PWM_ATTR+
DGND
DGND
* Decoupling CAP for reduce Impedance of 24VF
DGND
[FUSER_CONTROL] R101
nS_5V_OFF D33
CN201-1 +24VF
AN_READ_CHA
nS_5V_OFF 05.04.01
nHEATER_ON
AN_READ_T_1 R151
L37
C102
F
nHEATER_ON AN_READ_ATTR
CLP-600
daVinci MAIN GDI
DGND Rev 0.4
DGND
SMPS & HVPS 15/21
Service Manual
11-15
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(16/21) Schematic Diagram
1 2 3 4 5 6 7 8
A
RESERVED A
CN23-1
+5V [BLDC OPC] +5V
CN200-1
+5V
+5V
+5V CN200-2
CN200-3
+5V
R215 R214 R213 CN200-4
R520 R519 R522
CN200-5
Q13 R226
CN200-6 Q21 R523
B B
R225 CN200-7 +3.3V
R528
nBLDC_START2 CN200-8
nBLDC_START1
+3.3V CN200-9 +5V R521
CN200-10
Q20
R212 R527
U10-6 Q19 R524
FGND nBLDC_RDY1
DGND DGND FGND
R208
DGND DGND R525
nBLDC_RDY2
C509
C185
C508
C510
Q12
Q18
DGND
R217 DGND DGND
BLDC_CLK2 C513 R526
DGND DGND DGND
C BLDC_CLOCK2 BLDC_CLK1 C512 C
BLDC_CLOCK1
ELECTRONICS CO., LTD.
ALL RIGHTS RESERVED
DGND
DGND
RESERVED
SAMSUNG
+24VF
IH BOARD +5V
D CN103-1
+5V +3.3V
R509
DGND DGND R514
U46-6 U46-5
C507
C506
DGND DGND
CLP-600
daVinci MAIN GDI
Rev 0.4
Service Manual
11-16
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(17/21) Schematic Diagram
1 2 3 4 5 6 7 8
[DRIVER]
A A
CN18-1
+24VF +24VF
CN18-2
CN18-3 CN18-4
RA17 RA29
DGND DGND
B B
CN18-5 CN18-6
SM_YM_A nSM_YM_EN0
CN18-7 CN18-8
SM_YM_B nSM_YM_AM
CN18-9 CN18-10
SM_CK_A nSM_CK_EN0
C C
CN18-11 CN18-12
SM_CK_B nSM_CK_AM
ELECTRONICS CO., LTD.
+3.3V
ALL RIGHTS RESERVED
R227 R3
CN18-13 CN18-14
SAMSUNG
nFAN_FUSER nFAN_SMPS
+24VF
D
CN18-15 CN18-16
nSOL_PICKUP nSOL_MP
+3.3V
CN18-17 CN18-18
D16 C309
CN18-19 CN18-20
R172 DGND DGND
DGND nS_EMPT
+24VF
C127
E D17
C307
C308
C151
DGND
CN18-25 CN18-26
SM_DEV_K_A
CN18-27 CN18-28
DGND 05.04.01
DGND DGND
SM_DEV_K_B
F CN18-29 CN18-30
nSM_DEV_K_EN0 nSM_DEV_K_AM
CLP-600
daVinci MAIN GDI
Rev 0.4
DRIVER INTERFACE 17/21
Service Manual
11-17
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(18/21) Schematic Diagram
1 2 3 4 5 6 7 8
A A
Page Function
1 Index
B 2 Clock(ICS9248) & Power On Reset B
3 CPU ( RM5231A )
4 System Controller ( V320USC )
5 Aribiter PLD, Latch, 245
6 Memory ( Flash & SDRAM ), EEPROM
7 Panel UART
C
8 USB Controller ( ISP1582) C
10 HYPER-C
11 LPEC2
12 SCF, CRUM_DEVE
SAMSUNG
05.04.01
CLP-600
daVinci Main GDI
Rev 0.4
INDEX 1/21
Service Manual
11-18
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(19/21) Schematic Diagram
1 2 3 4 5 6 7 8
A A
+5VA
C32 R60 Q1
U8-2
R232 NHEATER1
nHEATER_FUSER
+2.5VA GNDA
U8-1
Q9
B B
R51
DGND nHEATER_ON GNDA
D12
R64
R65
+2.5VA
GNDA
D9
TH_FUSER R54 R46
R44 FGND
SMW200-04P
GNDA
CN8 TP838
R43 TH1
C A_TH_FUSER1 C
Q8
TP839
ELECTRONICS CO., LTD.
L5
ALL RIGHTS RESERVED
C31 R45
C30
SAMSUNG
nS_NEW_FUSER R565
nCUT_FUSER
DGND DGND
C33
DGND
05.04.01
CLP-600
daVinci MAIN GDI
Rev 0.4
FUSER 19/21
Service Manual
11-19
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(20/21) Schematic Diagram
1 2 3 4 5 6 7 8
A A
CN14-1
R120 R142
+5V
C331 DGND
C313 C310 +5V
R143
U100-1 U100-2
GNDA
Q14 GNDA R350 R342
DGND R351
PWM_CR_1
B B
AN_CR_1 U25-1
AN_CR_1 C311
U30-1 C289
nS_ACR_1
R133
C99
C290 GNDA +3.3V
C292 R149
GNDA GNDA
R134
R344 R345
R348
GNDA GNDA +3.3V_CRUM
DGND DGND
GNDA
SCL_BELT
ELECTRONICS CO., LTD.
R263
SDA_BELT
ALL RIGHTS RESERVED
L40
+5V +3.3V
C332
SAMSUNG
R140 R136
R139
D U30-2 AN_CR_2
AN_CR_2 U25-2
nS_ACR_2 DGND
R153
C291
R148 C293 R137 C95
R349
GNDA GNDA
DGND DGND
GNDA
U29-1 U29-2
Q11 GNDA R158 R343
R157
COVER_CLOSED PWM_CR_2
C312
C108
GNDA
F R346 R347
CLP-600
daVinci MAIN GDI
GNDA GNDA
Rev 0.4
COLOR REGI I/F 20/21
Service Manual
11-20
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Main Board(21/21) Schematic Diagram
1 2 3 4 5 6 7 8
A +5V A
R560
L42 30ohm/3A
C519
C526
2203-000189
47uF(MLCC)
2007-000090
R566
DGND DGND
C518
C559
2007-000134
2203-000903 SI4542DY,6A
MAX6691MUB DGND 1205-002339 R564
SC4603 28.7K , 1%
47uF(MLCC)
47uF(MLCC)
DGND
1009-P00003 DGND 2007-000129
R561
R563
2007-000093 C573 C574 C575 C576 C577 C578 C579 C580 C581 C582
DGND DGND
C C
2203-000783
2007-000079
R541
ELECTRONICS CO., LTD.
2007-000965
ALL RIGHTS RESERVED
DGND
C583 C584 C585 C586 C587
SAMSUNG
D
+5V +3.3V
U176
DGND
L39
2007-000309
R577
2401-000426
C541
R579 475KOHM , 1%
C543
R572
2007-000100
2203-000189
E
DGND
1203-PR0576
DGND DGND
05.04.01
CLP-600
daVinci Main GDI
Rev 0.4
INDEX 21/21
Service Manual
11-21
Samsung Electronics
This Document can not be used without Samsung’s authorization.
11.2 LCD Panel(1/2) Schematic Diagram
1 2 3 4 5 6 7
53015-0510
VCC
04-6232-106-103-800
+5V
2 C16
A CN2-2 A
C6 10uF
GND 100nF 16V
1 R11 VCC
CN2-1
10K D3
DGND 2 1
R12 3
10K DGND
Q12 Q13
MMBT2222ALT1 MMBT2222ALT1
/OPE_RST 1 3
4
R3 1 3 2
C9
CN2-4 100nF
1K 2 C14
C10 R13
100nF 10K 1nF
DGND
B B
DGND
R1
5
CN2-5
200
OPE_TXD VCC
C12
100pF VCC
R14 R15 U1
10K 10K
DGND
SAMSUNG ELECTRONICS CO., LTD.
R2 35 36
Q14 _RESET VDD
OPE_RXD MMBT2222ALT1 3 48 OSC1 20 C11 C7
1
Q15 200 C13 47
TXD _INT
100nF 100nF
3 RXD TMR0 21
3 1 2 100pF DGND
ALL RIGHTS RESERVED
CN2-3 37 34
R4 2 XTAL1 TMR1
1K R16 C15 MMBT2222ALT1 C1 38
XTAL2 LED0 6
10K 1nF 47pF 11 5
NC1 LED1
12 4
NC2 LED2
C DGND C2 13 3 C
NC3 LED3
DGND DGND 47pF 14
NC4 LED4 46
4 LCD_RS CSACS_7.37MHz 8 45
CN1-4 LCD_RW LCD_RS LED5
5 9 44
CN1-5 LCD_E LCD_RWLED6
6 10 43
CN1-6 LCD_D0 LCD_E LED7
7 30 39
CN1-7 LCD_D1 LCD_D0 NC5
8 31 40
CN1-8 LCD_D2 LCD_D1 NC6
JTP1280A6 SW5
9 32 41
CN1-9 LCD_D3 LCD_D2 NC7 SW1 1 2 1 2 VCC
10 33 42
CN1-10 LCD_D3 NC8 R6
11 LCD_D4 18 22
CN1-11 LCD_D5
LCD_D4 KEY0
12 17 23
CN1-12 LCD_D6 LCD_D5 KEY1 10K
CN1-13 13 16
LCD_D6 KEY2 24 SW2 SW6
14 LCD_D7 15 25 1 2 1 2
CN1-14 R10 LCD_D7 KEY3
R7
VCC 2 26
VCC VCC SENSORKEY4
10K 1 27
D_DET KEY5
7 28 10K
D C3 C4 C5 D_SCAN KEY6 SW3 SW7 D
3 19 29
CN1-3 R5 VSS KEY7 1 2 1 2
2 10K R8
CN1-2
C8 22pF 22pF 22pF HT48R50
DGND DGND 10K
SW4
100nF R17
CN1-1 1 1 2
510 R9
D1 10K
DGND DGND
MMSD914T1
D2
MMSD914T1 E
E SIGN J.I.Kim
C
A H E D Davinci
R E N W
P C G G Panel
. K . .
rev 0.2
Service Manual
11-22
Samsung Electronics
This Document can not be used without Samsung’s authorization.
LCD Panel(2/2) Schematic Diagram
1 2 3 4 5 6 7
VCC
DGND
B C17 B
VCC
100nF
DGND
R36 R37 R38 R39
390 390 390 390
SAMSUNG ELECTRONICS CO., LTD.
Q8 Q9 Q10
2 2 2
Q11 2
1 1 1 1
3 3 3 3
ALL RIGHTS RESERVED
DGND
C18
VCC 100nF
VCC
R18 DGND
10K
Q16
D MMBT2222ALT1 R30 D
300
1 3
2
DGND Q1
1 2
3
KSA1182-Y LED10
1
2
VCC
SAM5270-B
E
DGND
R29
Q2 240
1 2 ED. DATE 1 04.11.22 2 3
E 3
KSA1182-Y SIGN J.I.Kim
C
A H E D
R E N W Davinci
P C G G Panel
. K . .
rev 0.2
Service Manual
11-23
Samsung Electronics
This Document can not be used without Samsung’s authorization.
11.3 LED Panel(1/2) Schematic Diagram
1 2 3 4 5 6 7
53015-0510
VCC
+5V
2 C12
A CN2-2 A
C3 10uF
GND 100nF 16V
1 R8 VCC
CN2-1
10K D3
DGND 2 1
R9 3
10K DGND
Q12 Q13
MMBT2222ALT1 MMBT2222ALT1
/OPE_RST 1 3
4
R3 1 3 2
C5
CN2-4 100nF
1K 2 C10
C6 R10
100nF 10K 1nF
DGND
B B
DGND
R1
5
CN2-5
200
OPE_TXD VCC
C8
100pF VCC
R11 R12 U1
10K 10K
DGND
SAMSUNG ELECTRONICS CO., LTD.
R2 35 36
Q14 _RESET VDD
OPE_RXD MMBT2222ALT1 3 OSC1 48 20 C7 C4
1
Q15 200 C9 47
TXD _INT
100nF 100nF
3 RXD TMR0 21
3 1 2 100pF DGND
ALL RIGHTS RESERVED
CN2-3 37 34
R4 2 XTAL1 TMR1
1K R13 C11 MMBT2222ALT1 C1 38
XTAL2 LED0 6
10K 1nF 47pF 11 5
NC1 LED1
12 4
NC2 LED2
C DGND C2 13 3 C
NC3 LED3
DGND DGND 47pF 14 46
NC4 LED4
CSACS_7.37MHz 8 45
LCD_RS LED5
9 44
LCD_RWLED6
10
LCD_E LED7 43 VCC
30 39
LCD_D0 NC5
31 40
LCD_D1 NC6
32 41
LCD_D2 NC7 SW6
33 42
LCD_D3 NC8 1 2
18 22
LCD_D4 KEY0 R5
17 23
LCD_D5 KEY1
16 24
LCD_D6 KEY2 10K
15
LCD_D7 KEY3 25 SW7
VCC R7 2 26 1 2
SENSORKEY4
10K 1 27 R6
D_DET KEY5
7 28
D D_SCAN KEY6 D
19 29 10K
VSS KEY7
HT48R50
DGND
D2
MMSD914T1 E
E SIGN J.I.Kim
C
A H E D Davinci
R E N W
P C G G Panel
. K . .
rev 0.1
Service Manual
11-24
Samsung Electronics
This Document can not be used without Samsung’s authorization.
LED Panel(2/2) Schematic Diagram
1 2 3 4 5 6 7
VCC
DGND
B C13 B
VCC
100nF
DGND
R32 R33 R34 R35
390 390 390 390
SAMSUNG ELECTRONICS CO., LTD.
Q8 Q9 Q10
2 2 2
Q11 2
1 1 1 1
3 3 3 3
ALL RIGHTS RESERVED
DGND
C14
VCC 100nF
VCC
R14 DGND
10K
Q16
D MMBT2222ALT1 R26 D
300
1 3
2
DGND Q1
1 2
3
KSA1182-Y LED10
1
2
VCC
SAM5270-B
E
DGND
R25
Q2 240
1 2 ED. DATE 1 04.11.22 2 3
E 3
KSA1182-Y SIGN J.I.Kim
C
A H E D
R E N W Davinci
P C G G Panel
. K . .
rev 0.1
Service Manual
11-25
Samsung Electronics
This Document can not be used without Samsung’s authorization.
11.4 CR Sensor Schematic Diagram
1 2 3 4 5 6 7 8
A A
B B
C C
ELECTRONICS CO., LTD.
ALL RIGHTS RESERVED
SAMSUNG
Service Manual
11-26
Samsung Electronics
This Document can not be used without Samsung’s authorization.
11.5 DEVE-CRUM IF Schematic Diagram
1 2 3 4 5 6 7 8
A A
B B
C C
ELECTRONICS CO., LTD.
ALL RIGHTS RESERVED
SAMSUNG
Service Manual
11-27
Samsung Electronics
This Document can not be used without Samsung’s authorization.
11.6 DEVE-CRUM IF Schematic Diagram
1 2 3 4 5 6 7 8
A A
B B
C C
ELECTRONICS CO., LTD.
ALL RIGHTS RESERVED
SAMSUNG
Service Manual
11-28
Samsung Electronics
This Document can not be used without Samsung’s authorization.
11.7 Driver(1/3) Schematic Diagram
Service Manual
11-29
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Driver(2/3) Schematic Diagram
Service Manual
11-30
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Driver(3/3) Schematic Diagram
Service Manual
11-31
Samsung Electronics
This Document can not be used without Samsung’s authorization.
11.8 SMPS (1/2) Schematic Diagram
Service Manual
11-32
Samsung Electronics
This Document can not be used without Samsung’s authorization.
SMPS (2/2) Schematic Diagram
CON51
1
2
CON51 AR02
DSS-601M
AR03 TNR11 C30 F71 24V1/4A
F01 DSS-601M F02 H71 RUE500 250V4A CON4-#1,3,5
1 2
14D561 400V332
2
250V15A 250V8A BD01 VCC
4
CON
CON01 C05
R01 LF02 275V684
200K_C3216 4 - + 1 FET H/S AGND FGND F72 24V2/4A
2
1 TNR01 C01 C02 LSA10165 H72 RUE500 250V4ACON4-#7,9,11
2 275V684 TH01 + C11 C13 1 2
D
14D221K AR01 10D-15 630V473 Q11
LF01 275V474 D15SB60 250V860uF 1 STW26NM60
G
S
R02
3
200K_C3216 LHA13013 DSS-601M t + C12
RL01 C71 F73 24V3/2A
3
4
5
250V860uF H73 RUE500 250V4A CON4-#13,15
C04 C03 1 2
400V152 400V152 LKP1AF-24V
R03
200K_C3216 17V D71
2
1
3
AGND
2
R39 1 2
1 Q13
FGND 2222A 3
1/2W120
10K_C2012
YG865C15R
33
AGND R12 D72
17V 1 Q14 1 2
2907 1,2
3 + C72 + C73 + C74 + C75 + C76 + C77 C78
35V1500UF
35V1500UF
35V1500UF
35V1500UF
35V1500UF
35V1500UF
R25 R26 R13 R71
100V 104
150 (2012) YG865C15R
1K_C2012
8,9,10 D73
+5V R22 R23 200 (2012) 2.2_C2012 1 2
1_C2012 10_C2012 D11 3,4
FS1M 3
2A205_C2012
1 2 C22 17V
2A205_C2012
YG865C15R
R17 C20 C21 12,13,14
100K_C2012
2
R75 2A105_C2012 R24 6,7 GND
270_C2012 C16 10K_C2012 R28 150 CON4-#2,4,6,8,10,12,14,16
2
2
MMBT2222A 2A102_C2012 CS 5 2 14 Q15
R18 7 OUT 3 IN N1 13 1 2222A EER4242 T11
1
CT SD VB
1K_C2012
2.7K_C2012 10K_C2012 5 12 R14
3
3
1 4 VSS HD 11 PC71-1 R72 R91
R20 Lp=91uH
1
RT DT VS
GND
10K_C2012
PC73 3 6 10 18K_C2012
33
LTV817 C18 2 IS 7 COM N2 9 2.2_C2012 LTV817
2A102_C2012 FB 1K_C2012 1 LO N3 8 1 C14 C15
2
7552 VCC N4 Q16 R15
4
630V334
630V334
IR21094 2907
2
2
+
10K_C2012 C19 50V1uF R92
2A472_C2012 1.2K_C2012
200 5W0.025
2
AGND PC71-2 U91 1
STANDBY
3
LTV817 KA431
CON4-#27 R93
3
AGND AGND
AGND 2.2K_C2012
17V +5V1_4A
D74 L72 5uF F74
C25 1 2 CON4-#17,19,21
R30 R33 630V 103
R37 3 250V4A
4
2W 100K
PC72-2 2M_2012 *3 1M_2012 *3 YG865C06R F75 +5V2_2A
LTV817 R31 R34 CON4-#23,25
+ C82 + C83 + C84 250V4A
10V3300uF
10V3300uF
10V3300uF
2
3
D12 R73
R32 R35 FS1M 100_C2012
2 24V2_4A 24V1_4A
7,8
1 U13
1
C TOP245Y 24V3_2A
3 3 6,10
R29 X 1 2
2
L
GND 3 4
6.8_C2012 R36 7 5 6
10KF_C2012 4 D 5 7 8
CON4-#18,20,22,24,26
1
S
F
R94 9 10
C23 C26 R38 PC72-1 43_C2012 11 12
FGND
+ C24 68pF_2012 0 R74 13 14
5
2
2 1 +5V2_2A 19 20
EER2525 T12 21 22
D13 23 24
FS1M + C92 R95 25 26
1K_C2012 STANDBY27 28
+ C27 50V 1uF
2
35V100uF
U92 1
FGND
KA431
3
AGND R96
1K_C2012
Service Manual
11-33
Samsung Electronics
This Document can not be used without Samsung’s authorization.
11.9 HVPS(1/9) Schematic Diagram
Service Manual
11-34
Samsung Electronics
This Document can not be used without Samsung’s authorization.
HVPS(2/9) Schematic Diagram
Service Manual
11-35
Samsung Electronics
This Document can not be used without Samsung’s authorization.
HVPS(3/9) Schematic Diagram
Service Manual
11-36
Samsung Electronics
This Document can not be used without Samsung’s authorization.
HVPS(4/9) Schematic Diagram
Service Manual
11-37
Samsung Electronics
This Document can not be used without Samsung’s authorization.
HVPS(5/9) Schematic Diagram
Service Manual
11-38
Samsung Electronics
This Document can not be used without Samsung’s authorization.
HVPS(6/9) Schematic Diagram
Service Manual
11-39
Samsung Electronics
This Document can not be used without Samsung’s authorization.
HVPS(7/9) Schematic Diagram
Service Manual
11-40
Samsung Electronics
This Document can not be used without Samsung’s authorization.
HVPS(8/9) Schematic Diagram
Service Manual
11-41
Samsung Electronics
This Document can not be used without Samsung’s authorization.
HVPS(9/9) Schematic Diagram
Service Manual
11-42
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Reference Information
12
12. Reference Information
This chapter contains the tools list, list of abbreviations used in this manual, and a guide to the
location space required when installing the printer. A definition of tests pages and Wireless
Network information definition is also included.
• Driver
Standard : "-" type, "+" type (M3 long, M3 short, M2 • Vacuum Cleaner
long, M2 short).
• Brush
• Tweezers
Standard : For general home use, small type.
• Cotton Swab
Standard : For general home use, for medical service.
• Software (Driver) installation CD ROM
Install Driver CD
Network S/W CD
Service Manual
12-1
Samsung Electronics
Reference Information
Service Manual
12-2
Samsung Electronics
Reference Information
Service Manual
12-3
Samsung Electronics
Reference Information
Service Manual
12-4
Samsung Electronics
Reference Information
Service Manual
12-5
Samsung Electronics
Reference Information
• Types of desk top PC (or Lap top) that uses the wireless LAN.
Service Manual
12-6
Samsung Electronics