Beruflich Dokumente
Kultur Dokumente
1 5
Note
Read measured value block 004 for multi-function switch
before performing electrical check.
Make sure that selector lever cable is properly adjusted
Automatic gearbox 01V, front-wheel drive and four-wheel
drive; Rep. Gr.37.
– On vehicles fitted with auxiliary heater,
remove screws -arrows- securing exhaust
pipe of auxiliary/ additional heater to noise
insulation.
vw-wi://rl/A.en-GB.A04.5607.89.wi::23493725.xml?xsl=3 14.02.2014
Checking multi-function switchF125 with 8-pin connector .2 5
Contacts Items tested Test conditions and Specification Fault rectification if readout
on -F125- additional steps does not match specification
1+2 Multi-function Ignition switched off
switch -F125- Switch to resistance
measuring range
– Selector lever in “P”, Less than 1 – Check connector at multi-
“N”, “D” function switch for contact
corrosion, moisture or loose
– Selector lever in “R”, fitting
“4”, “3”, “2”
– Check selector lever cable
1+3 – Selector lever in “R”, Less than 1 adjustment Automatic
“N”, “4” gearbox 01V, front-wheel drive
and four-wheel drive; Rep.
– Selector lever in “P”, Gr.37
“D”, “3”, “2” – Renew multi-function switch
Automatic gearbox 01V,
1+4 – Selector lever in “N”, Less than 1 front-wheel drive and four-
“D”, “4”, “2” wheel drive; Rep. Gr.37
vw-wi://rl/A.en-GB.A04.5607.89.wi::23493725.xml?xsl=3 14.02.2014
Checking multi-function switchF125 with 8-pin connector .3 5
– Selector lever in
“P”,“R”, “3”
1+5 – Selector lever in “D”, Less than 1
“4”, “3”
– Selector lever in “P”,
“R”, “N”, “2”
Contacts Items tested Test conditions and Specification Fault rectification if readout
on -F125- additional steps does not match specification
6+7 P/N signal from Ignition switched off
multi-function Switch to resistance
switch -F125- measuring range
– Selector lever in “R”, – Check connector at multi-
“D”, “4”, “3”, “2” function switch for contact
corrosion, moisture or loose
fitting
– Check selector lever cable
adjustment Automatic
gearbox 01V, front-wheel drive
– Selector lever in “P”, Less than 1 and four-wheel drive; Rep.
“N” Gr.37
– Renew multi-function switch
Automatic gearbox 01V,
front-wheel drive and four-
wheel drive; Rep. Gr.37
Contacts Items tested Test conditions and Specification Fault rectification if readout
on -F125- additional steps does not match specification
1+8 Reversing light Ignition switched off
signal from Switch to resistance
multi-function measuring range
switch -F125-
– Selector lever in “P”, – Check connector at multi-
“N”, “D”, “4”, “3”, “2” function switch for contact
corrosion, moisture or loose
fitting
– Check selector lever cable
adjustment Automatic
gearbox 01V, front-wheel drive
and four-wheel drive; Rep.
Gr.37
– Selector lever in “R” Less than 1
– Renew multi-function switch
Automatic gearbox 01V,
front-wheel drive and four-
wheel drive; Rep. Gr.37
vw-wi://rl/A.en-GB.A04.5607.89.wi::23493725.xml?xsl=3 14.02.2014
Checking multi-function switchF125 with 8-pin connector .4 5
switch
– Connect multimeter for voltage
measurement between contacts -1- and -6-
of the 8-pin connector.
– Switch on ignition.
Specification: approx. battery voltage.
If readout does not match specification:
– Repair wiring Current flow diagrams,
Electrical fault finding and Fitting locations.
Note
If readout does not match specification, rectify open circuit in
vw-wi://rl/A.en-GB.A04.5607.89.wi::23493725.xml?xsl=3 14.02.2014
Checking multi-function switchF125 with 8-pin connector .5 5
vw-wi://rl/A.en-GB.A04.5607.89.wi::23493725.xml?xsl=3 14.02.2014