Beruflich Dokumente
Kultur Dokumente
Contents
1 Overview
2 Methods
3 Development
4 See also
5 References
6 Further reading
7 External links
Overview
Geophysical survey is used to create maps of subsurface archaeological features.
Features are the non-portable part of the archaeological record, whether standing
structures or traces of human activities left in the soil. Geophysical instruments
can detect buried features when their physical properties contrast measurably with
their surroundings. In some cases individual artifacts, especially metal, may be
detected as well. Readings taken in a systematic pattern become a data set that can
be rendered as image maps. Survey results can be used to guide excavation and to
give archaeologists insight into the patterning of non-excavated parts of the site.
Unlike other archaeological methods, geophysical survey is neither invasive nor
destructive. For this reason, it is often used where preservation (rather than
excavation) is the goal, and to avoid disturbance of culturally sensitive sites
such as cemeteries.[1]
Although geophysical survey has been used in the past with intermittent success,
good results are very likely when it is applied appropriately. It is most useful
when it is used in a well-integrated research design where interpretations can be
tested and refined. Interpretation requires a knowledge both of the archaeological
record, and of the way it is expressed geophysically. Appropriate instrumentation,
survey design, and data processing are essential for success, and must be adapted
to the unique geology and archaeological record of each site. In the field, control
of data quality and spatial accuracy are critical.
Methods
EM conductivity survey
Geophysical methods used in archaeology are largely adapted from those used in
mineral exploration, engineering, and geology. Archaeological mapping presents
unique challenges, however, which have spurred a separate development of methods
and equipment. In general, geological applications are concerned with detecting
relatively large structures, often as deeply as possible. In contrast, most
archaeological sites are relatively near the surface, often within the top meter of
earth. Instruments are often configured to limit the depth of response to better
resolve the near-surface phenomena that are likely to be of interest. Another
challenge is to detect subtle and often very small features � which may be as
ephemeral as organic staining from decayed wooden posts - and distinguish them from
rocks, roots, and other natural �clutter.� To accomplish this requires not only
sensitivity, but also high density of data points, usually at least one and
sometimes dozens of readings per square meter.
Every kind of material has unique magnetic properties, even those that we do not
think of as being �magnetic.� Different materials below the ground can cause local
disturbances in the Earth�s magnetic field that are detectable with sensitive
magnetometers. Magnetometers react very strongly to iron and steel, brick, burned
soil, and many types of rock, and archaeological features composed of these
materials are very detectable. Where these highly magnetic materials do not occur,
it is often possible to detect very subtle anomalies caused by disturbed soils or
decayed organic materials. The chief limitation of magnetometer survey is that
subtle features of interest may be obscured by highly magnetic geologic or modern
materials.
GPR survey
Ground-penetrating radar (GPR) is perhaps the best known of these methods (although
it is not the most widely applied in archaeology). The concept of radar is familiar
to most people. In this instance, the radar signal � an electromagnetic pulse � is
directed into the ground. Subsurface objects and stratigraphy (layering) will cause
reflections that are picked up by a receiver. The travel time of the reflected
signal indicates the depth. Data may be plotted as profiles, or as planview maps
isolating specific depths.
GPR can be a powerful tool in favorable conditions (uniform sandy soils are ideal).
It is unique both in its ability to detect some spatially small objects at
relatively great depths and in its ability to distinguish the depth of anomaly
sources. The principal disadvantage of GPR is that it is severely limited by less-
than-ideal conditions. The high electrical conductivity of fine-grained sediments
(clays and silts) causes conductive losses of signal strength; rocky or
heterogeneous sediments scatter the GPR signal. Another disadvantage is that data
collection is relatively slow.
Metal detectors use electromagnetic induction to detect metal. Although other types
of instruments (notably magnetometers and electromagnetic conductivity meters) have
some sensitivity to metal, specialized metal detectors are much more effective.
Metal detectors are available in different configurations, varying in
sophistication and sensitivity. Most have some capacity to discriminate between
different types of metallic targets.
Common hand-held metal detectors are widely used by archaeologists. Most of these
instruments do not create a logged data set and thus cannot be used for directly
creating maps, but used in a systematic manner they can be a useful tool in
archaeological research. Sometimes external data loggers are attached to such
detectors which collect information about detected materials and corresponding gps
coordinates for further processing. Misuse of these instruments on archaeological
sites by treasure hunters and artifact collectors has been a serious problem in
archaeological preservation [4][5][6] however cooperative efforts between skilled
amateur operators and academic teams are emerging in the field.[7]
Lidar (LIght raDAR) is an optical remote sensing technology that can measure the
distance to a target by illuminating the target with light, often using pulses from
a laser. Lidar has many applications in the field of archaeology including aiding
in the planning of field campaigns, mapping features beneath forest canopy,[8] and
providing an overview of broad, continuous features that may be indistinguishable
on the ground. Lidar can also provide archaeologists with the ability to create
high-resolution digital elevation models (DEMs) of archaeological sites that can
reveal micro-topography that are otherwise hidden by vegetation. Lidar-derived
products can be easily integrated into a Geographic Information System (GIS) for
analysis and interpretation.
Data processing and imaging convert raw numeric data into interpretable maps. Data
processing usually involves the removal of statistical outliers and noise, and
interpolation of data points. Statistical filters may be designed to enhance
features of interest (based on size, strength, orientation, or other criteria), or
suppress obscuring modern or natural phenomena. Inverse modeling of archaeological
features from observed data is becoming increasingly important. Processed data are
typically rendered as images, as contour maps, or in false relief. When geophysical
data are rendered graphically, the interpreter can more intuitively recognize
cultural and natural patterns and visualize the physical phenomena causing the
detected anomalies.
Development
File:Geophys at Pembroke Castle.webm
A magnetic survey at Pembroke Castle carried out by Dyfed Archaeological Trust.[9]
The use of geophysical survey is well established in European archaeology,
especially in Great Britain, where it was pioneered in the 1940s and 1950s. It is
increasingly employed in other parts of the world, and with increasing success as
techniques are adapted to unique regional conditions.
Although the sensitivity of sensors has improved, and new methods have been
developed, the most important developments have been automated data logging and
computers to handle and process large amounts of data. Continuing improvements in
survey equipment performance and automation have made it possible to rapidly survey
large areas. Rapid data collection has also made it practical to achieve the high
sample densities necessary to resolve small or subtle features. Advances in
processing and imaging software have made it possible to detect, display, and
interpret subtle archaeological patterning within the geophysical data.