Beruflich Dokumente
Kultur Dokumente
chassis PL11.0
TYPE B
32PFL3506/F7 PHILIPS (Serial No.: DS2)
32PFL3506/F7 PHILIPS (Serial No.: DS3)
32PFL3000/F8 PHILIPS (Serial No.: XA2)
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.
111128
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all
P&F Equipment. The service procedures recommended by P&F and
described in this service manual are effective methods of performing
service operations. Some of these service special tools should be used
when and as recommended.
It is important to note that this service manual contains various CAUTIONS
and NOTICES which should be carefully read in order to minimize the risk
of personal injury to service personnel. The possibility exists that improper
service methods may damage the equipment. It also is important to
understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE.
P&F could not possibly know, evaluate and advice the service trade of all
conceivable ways in which service might be done or of the possible
hazardous consequences of each way. Consequently, P&F has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a
service procedure or tool which is not recommended by P&F must first use
all precautions thoroughly so that neither his safety nor the safe operation
of the equipment will be jeopardized by the service method selected.
1-1 PL11.0SP
IMPORTANT SAFETY PRECAUTIONS
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical
codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally
important to implement the following precautions when a set is being serviced.
Safety Precautions for LCD TV d. Leakage Current Hot Check - With the
instrument completely reassembled, plug the
Circuit AC line cord directly into a 120 V AC outlet. (Do
1. Before returning an instrument to the not use an isolation transformer during this
customer, always make a safety check of the test.) Use a leakage current tester or a
entire instrument, including, but not limited to, the metering system that complies with American
following items: National Standards Institute (ANSI) C101.1
a. Be sure that no built-in protective devices are Leakage Current for Appliances and
defective and have been defeated during Underwriters Laboratories (UL) 1410, (50.7).
servicing. (1) Protective shields are provided With the instrument AC switch first in the on
on this chassis to protect both the technician position and then in the off position, measure
and the customer. Correctly replace all missing from a known earth ground (metal water pipe,
protective shields, including any removed for conduit, etc.) to all exposed metal parts of the
servicing convenience. (2) When reinstalling instrument (antennas, handle brackets, metal
the chassis and/or other assembly in the cabinet, screw heads, metallic overlays, control
cabinet, be sure to put back in place all shafts, etc.), especially any exposed metal
protective devices, including but not limited to, parts that offer an electrical return path to the
nonmetallic control knobs, insulating chassis. Any current measured must not
fishpapers, adjustment and compartment exceed 0.5 milli-ampere. Reverse the
covers/shields, and isolation resistor/capacitor instrument power cord plug in the outlet and
networks. Do not operate this instrument or repeat the test.
permit it to be operated without all
protective devices correctly installed and READING SHOULD
functioning. Servicers who defeat safety NOT BE ABOVE 0.5 mA
features or fail to perform safety checks
may be liable for any resulting damage. LEAKAGE
DEVICE CURRENT
b. Be sure that there are no cabinet openings BEING TESTER
through which an adult or child might be able to TESTED + _
insert their fingers and contact a hazardous
voltage. Such openings include, but are not TEST ALL EXPOSED
limited to, (1) spacing between the Liquid METAL SURFACES
Crystal Panel and the cabinet mask, (2)
excessively wide cabinet ventilation slots, and
(3) an improperly fitted and/or incorrectly ALSO TEST WITH
secured cabinet back cover. PLUG REVERSED
c. Antenna Cold Check - With the instrument AC USING AC
plug removed from any AC source, connect an ADAPTER PLUG EARTH
electrical jumper across the two AC plug AS REQUIRED GROUND
prongs. Place the instrument AC switch in the
on position. Connect one lead of an ohmmeter ANY MEASUREMENTS NOT WITHIN THE
to the AC plug prongs tied together and touch LIMITS SPECIFIED HEREIN INDICATE A
the other ohmmeter lead in turn to each tuner POTENTIAL SHOCK HAZARD THAT MUST
antenna input exposed terminal screw and, if BE ELIMINATED BEFORE RETURNING THE
applicable, to the coaxial connector. If the INSTRUMENT TO THE CUSTOMER OR
measured resistance is less than 1.0 megohm BEFORE CONNECTING THE ANTENNA OR
or greater than 5.2 megohm, an abnormality ACCESSORIES.
exists that must be corrected before the
2. Read and comply with all caution and safety-
instrument is returned to the customer. Repeat
related notes on or inside the receiver cabinet, on
this test with the instrument AC switch in the off
the receiver chassis, or on the Liquid Crystal
position.
Panel.
2-1 LTVN_ISP
3. Design Alteration Warning - Do not alter or add 7. Product Safety Notice - Some electrical and
to the mechanical or electrical design of this TV mechanical parts have special safety-related
receiver. Design alterations and additions, characteristics which are often not evident from
including, but not limited to circuit modifications visual inspection, nor can the protection they give
and the addition of items such as auxiliary audio necessarily be obtained by replacing them with
and/or video output connections, might alter the components rated for higher voltage, wattage, etc.
safety characteristics of this receiver and create a Parts that have special safety characteristics are
hazard to the user. Any design alterations or identified by a # on schematics and in parts lists.
additions will void the manufacturer's warranty and Use of a substitute replacement that does not
may make you, the servicer, responsible for have the same safety characteristics as the
personal injury or property damage resulting recommended replacement part might create
therefrom. shock, fire, and/or other hazards. The product's
4. Hot Chassis Warning - safety is under review continuously and new
instructions are issued whenever appropriate.
a. Some TV receiver chassis are electrically
Prior to shipment from the factory, our products
connected directly to one conductor of the AC
are strictly inspected to confirm they comply with
power cord and maybe safety-serviced without
the recognized product safety and electrical codes
an isolation transformer only if the AC power
of the countries in which they are to be sold.
plug is inserted so that the chassis is
However, in order to maintain such compliance, it
connected to the ground side of the AC power
is equally important to implement the following
source. To confirm that the AC power plug is
precautions when a set is being serviced.
inserted correctly, with an AC voltmeter,
measure between the chassis and a known
earth ground. If a voltage reading in excess of
1.0 V is obtained, remove and reinsert the AC
power plug in the opposite polarity and again
measure the voltage potential between the
chassis and a known earth ground.
b. Some TV receiver chassis normally have 85V
AC(RMS) between chassis and earth ground
regardless of the AC plug polarity. This chassis
can be safety-serviced only with an isolation
transformer inserted in the power line between
the receiver and the AC power source, for both
personnel and test equipment protection.
c. Some TV receiver chassis have a secondary
ground system in addition to the main chassis
ground. This secondary ground system is not
isolated from the AC power line. The two
ground systems are electrically separated by
insulation material that must not be defeated or
altered.
5. Observe original lead dress. Take extra care to
assure correct lead dress in the following areas: a.
near sharp edges, b. near thermally hot parts-be
sure that leads and components do not touch
thermally hot parts, c. the AC supply, d. high
voltage, and, e. antenna wiring. Always inspect in
all areas for pinched, out of place, or frayed wiring.
Check AC power cord for damage.
6. Components, parts, and/or wiring that appear to
have overheated or are otherwise damaged
should be replaced with components, parts, or
wiring that meet original specifications.
Additionally, determine the cause of overheating
and/or damage and, if necessary, take corrective
action to remove any potential safety hazard.
2-2 LTVN_ISP
Precautions during Servicing
A. Parts identified by the # symbol are critical for
safety.
Replace only with part number specified.
B. In addition to safety, other parts and assemblies
are specified for conformance with regulations
applying to spurious radiation. These must also be
replaced only with specified replacements.
Examples: RF converters, RF cables, noise
blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components
(transformers, power cord, etc.), wrap ends of
wires securely about the terminals before
soldering.
F. Observe that the wires do not contact heat
producing parts (heat sinks, oxide metal film
resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp
edged or pointed parts.
H. When a power cord has been replaced, check that
11~13 lb (5~6 kg) of force in any direction will not
loosen it.
I. Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder
droplets, etc.) do not remain inside the set.
K. When connecting or disconnecting the internal
connectors, first, disconnect the AC plug from the
AC supply outlet.
L. When installing parts or assembling the cabinet
parts, be sure to use the proper screws and
tighten certainly.
2-3 LTVN_ISP
Safety Check after Servicing
Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and
wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified
values in order to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm
specified clearance distance (d) and (d') between
soldered terminals, and between terminals and Chassis or Secondary Conductor
surrounding metallic parts. (See Fig. 1)
Primary Circuit
Table 1: Ratings for selected area
Clearance d' d
AC Line Voltage Region
Distance (d), (d’)
U.S.A. or ≥ 3.2 mm
110 to 130 V
Canada (0.126 inches)
Fig. 1
Fig. 2
AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to:
U.S.A. or 0.15 µF CAP. & 1.5 kΩ Exposed accessible
110 to 130 V i ≤ 0.5 mA rms
Canada RES. Connected in parallel parts
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
2-4 LTVN_ISP
STANDARD NOTES FOR SERVICING
Circuit Board Indications How to Remove / Install Flat Pack-IC
1. The output pin of the 3 pin Regulator ICs is
1. Removal
indicated as shown.
With Hot-Air Flat Pack-IC Desoldering Machine:
Top View Bottom View 1. Prepare the hot-air flat pack-IC desoldering
Input machine, then apply hot air to the Flat Pack-IC
Out In (about 5 to 6 seconds). (Fig. S-1-1)
Pin 1
10
3-1 TVN_SN
3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron:
be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from
pin or the solder lands under the IC when all pins of the flat pack-IC. When you use solder
removing it. flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
Hot-air
Flat Pack-IC Flat Pack-IC Desoldering Braid
Desoldering
Machine
CBA
Soldering Iron
Masking Flat Pack-IC Fig. S-1-3
Tape
Tweezers 2. Lift each lead of the flat pack-IC upward one by
one, using a sharp pin or wire to which solder will
Fig. S-1-2
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air desoldering
machine. (Fig. S-1-4)
Sharp
Pin
Fine Tip
Soldering Iron
Fig. S-1-4
3-2 TVN_SN
With Iron Wire: 2. Installation
1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA
flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more
you can remove it easily. (Fig. S-1-3) easily.
2. Affix the wire to a workbench or solid mounting 2. The “ I ” mark on the flat pack-IC indicates pin 1.
point, as shown in Fig. S-1-5. (See Fig. S-1-7.) Be sure this mark matches the
3. While heating the pins using a fine tip soldering pin 1 on the PCB when positioning for installation.
iron or hot air blower, pull up the wire as the solder Then presolder the four corners of the flat pack-IC.
melts so as to lift the IC leads from the CBA (See Fig. S-1-8.)
contact pads as shown in Fig. S-1-5. 3. Solder all pins of the flat pack-IC. Be sure that
4. Bottom of the flat pack-IC is fixed with glue to the none of the pins have solder bridges.
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6) Example :
5. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be
taken to ensure that the flat pack-IC is not
being held by glue. When the flat pack-IC is
removed from the CBA, handle it gently
because it may be damaged if force is applied.
Pin 1 of the Flat Pack-IC
is indicated by a " " mark.
Hot Air Blower Fig. S-1-7
or
Presolder
Iron Wire
Soldering Iron
To Solid
Mounting Point
Fig. S-1-5
Flat Pack-IC
CBA
Flat Pack-IC
Tweezers
Fig. S-1-6
3-3 TVN_SN
Instructions for Handling Semi-
conductors
Electrostatic breakdown of the semi-conductors may
occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.
<Incorrect>
CBA
1MΩ
CBA
1MΩ
Conductive Sheet or
Copper Plate
3-4 TVN_SN
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly Flowchart Step/
Fig.
Loc. Part Removal Note
This flowchart indicates the disassembly steps for the No.
No.
cabinet parts and the CBA in order to gain access to
items to be serviced. When reassembling, follow the IR Sensor D3
[8] CL103A ---
steps in reverse order. Bend, route and dress the CBA D4
cables as they were. Function D3 Function Knob,
[9] ---
[1] Stand
CBA D4 Knob Frame
Assembly
LCD
[10] Module D3 (S-11) ---
[8] IR Sensor
CBA
[2] Rear Assembly [7] Speaker Assembly
Front
[9] Function [11] D3 --------------- ---
[3] Inverter CBA Cabinet
CBA
↓ ↓ ↓ ↓ ↓
[4] Jack CBA
(1) (2) (3) (4) (5)
*1: TYPE A
[5] Power Supply
CBA *2: TYPE B
Note:
[6] Digital Main
CBA Unit (1) Order of steps in procedure. When reassembling,
follow the steps in reverse order. These numbers
[10] LCD Module are also used as the Identification (location) No. of
Assembly parts in figures.
[11] Front (2) Parts to be removed or installed.
Cabinet (3) Fig. No. showing procedure of part location
(4) Identification of parts to be removed, unhooked,
2. Disassembly Method unlocked, released, unplugged, unclamped, or
desoldered.
Step/ P = Spring, L = Locking Tab, S = Screw,
Fig.
Loc. Part Removal Note H = Hex Screw, CN = Connector
No.
No. e.g. 2(S-2) = two Screws of (S-2),
Stand 2(L-2) = two Locking Tabs of (L-2)
[1] D1 3(S-1) ---
Assembly (5) Refer to the following "Reference Notes in the
Rear 12(S-2), 2(S-3), Table."
[2] D1 ---
Assembly 4(S-4), 11(L-1)
7(S-5), CN1001,
Inverter D2 CN1003, CN1100,
[3] ---
CBA D4 CN1101, CN1102,
CN1901
D2
[4] Jack CBA 2(S-6), CL701B ---
D4
Power 9(S-7), CN101,
D2
[5] Supply CN301, CN302, ---
D4
CBA CN801, CN802
2(S-8), 8(S-9),
Digital Main D2 CN3902*1, CN3005*2,
[6] ---
CBA Unit D4 Jack Holder, Shield
Box
4(S-10),
[7] Speaker D3 ---
Speaker Holder
4-1 PL11.0-A_DC
[2] Rear Assembly
(L-1)
(S-2)
(L-1)
(S-4)
(S-2)
(L-1)
(L-1)
(S-2)
(S-2)
(S-4)
(S-3)
(S-2)
(S-1)
Fig. D1
4-2 PL11.0-A_DC
[3] Inverter CBA
(S-5)
(S-7)
Shield Box
(S-9)
(S-9)
(S-8)
4-3 PL11.0-A_DC
[11] Front Cabinet
Knob Frame
Speaker [7] Speaker
Holder
Fig. D3
4-4 PL11.0-A_DC
TV Cable Wiring Diagram
Jack
CBA Inverter CBA
CN1102
Power Supply CBA
CL701B
CN201
CN1001
CN1101
CL701A
CN301 AC CORD
CN101 CN802 CN801
To LCD Module
Assembly
To Speaker
Digital Main
CBA Unit Function
CBA
TYPE A CN3702
TYPE B CN3006
Fig. D4
4-5 PL11.0-A_DC
ELECTRICAL ADJUSTMENT INSTRUCTIONS
[32PFL3506/F7 (Serial No.: DS1, XA1), 32PFL3000/F8 (Serial No.: XA1)]
General Note: “CBA” is abbreviation for How to set up the service mode:
“Circuit Board Assembly.”
Note: Electrical adjustments are required after
Service mode:
replacing circuit components and certain 1. Turn the power on.
mechanical parts. It is important to perform 2. Press [MENU] button to display Setup menu.
these adjustments only after all repairs and 3. Select “Features”.
replacements have been completed.
4. Select “Current Software Info”.
Also, do not attempt these adjustments unless
the proper equipment is available. 5. Press [0], [6], [2], [5], [9], [6] and [INFO] buttons on
the remote control unit in this order. The following
Test Equipment Required screen appears.
1. NTSC Pattern Generator (Color Bar W/White "*" differs depending on the models.
Window, Red Color, Dot Pattern, Gray Scale,
Code : *******-***-*-*****-****
Monoscope, Multi-Burst) Pic code : **-*******-*****-**
2. Remote control unit MIPS : Push 0key
3. Color Analyzer
Tuner : ****-*****-****
Safety : safety_Non
5-1 A17F6EA
1. Purity Check Mode 2. VCOM Adjustment
This mode cycles through full-screen displays of red, Test Point Adj. Point
green, blue, and white to check for non-active pixels.
[CH + or -]
1. Enter the Service mode. Screen
buttons
2. Each time the [7] button on the remote control unit
is pressed, the display changes as follows. M. EQ. Spec.
Color analyzer See below
Purity Check Mode
Figure
White mode
Perpendicularity
[7] button
Black mode
L = 1.18 inches
Color Analyzer
[7] button
Red mode
1. Set the color analyzer at the zero point calibration
and bring the optical receptor pointing at the
center of the LCD-Panel at a distance of 1.18
inches(3cm) away from the LCD-Panel surface.
Note: The optical receptor must be set
[7] button perpendicularly to the LCD Panel surface.
Green mode 2. Enter the Service mode.
3. Press [2] button on the remote control unit.
4. Press [CH + or -] buttons on the remote control
unit so that the color analyzer value becomes
minimum within 2minutes from Power-On.
[7] button 5. To cancel or to exit from the VCOM Adjustment,
Blue mode press [PREV CH] button.
[7] button
White 20% mode
Note:
When entering this mode, the default setting is White mode.
5-2 A17F6EA
The White Balance Adjustment should be 5. [CUTOFF]
performed when replacing the LCD Panel Press [1] button to select “COR” for Red Cutoff
adjustment. Press [3] button to select “COB” for
or Digital Main CBA.
Blue Cutoff adjustment.
[DRIVE]
3. White Balance Adjustment Press [4] button to select “DR” for Red Drive
Purpose: To mix red and blue beams correctly for adjustment. Press [6] button to select “DB” for Blue
pure white. Drive adjustment.
Symptom of Misadjustment: White becomes bluish 6. In each color mode, press [CH + or -] buttons to
or reddish. adjust the values of color.
7. Adjust Cutoff and Drive so that the color
Test Point Adj. Point Mode Input temperature becomes 12000°K (x= 0.272 /
White Raster y= 0.278 ± 0.005).
[VOL -] [VIDEO1] (APL 70%) 8. To cancel or to exit from the White Balance
Screen
button C/D or Adjustment, press [PREV CH] button.
(APL 40%)
M. EQ. Spec.
Pattern Generator, x= 0.272 ± 0.005
Color analyzer y= 0.278 ± 0.005
Figure
L = 1.18 inches
INPUT: WHITE 70%, 40% Color Analyzer
Low High
Light Light
100IRE 100IRE
40%=40IRE 70%=70IRE
5-3 A17F6EA
[32PFL3506/F7 (Serial No.: DS2, DS3), 32PFL3000/F8 (Serial No.: XA2)]
General Note: “CBA” is abbreviation for How to set up the service mode:
“Circuit Board Assembly.”
Note: Electrical adjustments are required after
Service mode:
replacing circuit components and certain 1. Turn the power on.
mechanical parts. It is important to perform 2. Press [MENU] button to display Setup menu.
these adjustments only after all repairs and 3. Select “Features”.
replacements have been completed.
4. Select “Current Software Info”.
Also, do not attempt these adjustments unless
the proper equipment is available. 5. Press [0], [6], [2], [5], [9], [6] and [INFO] buttons on
the remote control unit in this order. The following
Test Equipment Required screen appears.
1. Remote control unit "*" differs depending on the models.
2. Color Analyzer, Code: *******-**-**-****-**
CA-310 (KONICA MINOLTA Luminance meter) or Pic code: **********-***-*-**
measuring instrument as good as CA-310. Panel-Option code: **-***-***-***-***
MIPS: Push 0 key
Tuner: ****-*****-****
Safety: Safety_Non
HDMI EDID: ** Total Watch Time: *****
PC EDID: ** Lightsensor: ****
5-4 A17FG_HEA
1. Purity Check Mode 2. VCOM Adjustment
This mode cycles through full-screen displays of red, Test Point Adj. Point
green, blue, and white to check for non-active pixels.
[CH + or -]
1. Enter the Service mode. Screen
buttons
2. Each time the [7] button on the remote control unit
is pressed, the display changes as follows. M. EQ. Spec.
Color analyzer See below
Purity Check Mode
Figure
White mode
To avoid interference from ambient
[7] button
light, this adjustment should be
performed in a dark room.
Perpendicularity
[7] button
Black mode
Color Analyzer
[7] button
Red mode
32PFL3506/F7 (Serial No.: DS2),
32PFL3000/F8 (Serial No.: XA2):
1. Set the color analyzer at the zero point calibration
and bring the optical receptor pointing at the
[7] button center of the LCD-Panel.
Green mode Note: The optical receptor must be set
perpendicularly to the LCD Panel surface.
2. Enter the Service mode.
3. Press [2] button on the remote control unit.
4. Press [CH + or -] buttons on the remote control
[7] button unit so that the color analyzer value becomes
Blue mode minimum.
5. To cancel or to exit from the VCOM Adjustment,
press [PREV CH] button.
5-5 A17FG_HEA
The White Balance Adjustment should be 6. Press [MENU] button. The internal Raster signal
performed when replacing the LCD Panel appears on the screen. (“Internal (Single)”
appears on the upper right of the screen as shown
or Digital Main CBA.
below.)
3. White Balance Adjustment
Purpose: To mix red and blue beams correctly for Internal (Single)
pure white.
Symptom of Misadjustment: White becomes bluish
or reddish.
ITEM SPECIFICATION
HDB 0
x= 0.272 ± 0.002
Color temperature
y= 0.278 ± 0.002
Internal pattern
Input Signal 7. Press [CH + or -] buttons to adjust the color
(40/70% raster)
temperature becomes 12000°K
Measurement point Screen center (x= 0.272 / y= 0.278 ±0.002).
CA-310 (KONICA MINOLTA 8. Press [1] button to select the “HDR” for High Drive
Luminance meter) or Red adjustment (“HDR” appears on the screen.)
M. EQ.
measuring instrument as and press [CH + or -] buttons to adjust the color
good as CA-310. temperature.
60min. 9. If necessary, adjust the “HDB” or “HDR” again.
Aging time (Retail MODE/100IRE Raster
HDMI 1080i@60) 10. Press [6] button to select the “LDB” for Low Drive
Blue adjustment (“LDB” appears on the screen.)
Shipment setting/ and press [CH + or -] buttons to adjust the color
MODE setting of TV
Retail MODE temperature.
Ambient
25°C ± 5°C
temperature
Internal (Single)
1. Operate the unit for more than 60 minutes.
2. Enter the Service mode.
3. Press [VOL -] button three times on the remote
control unit to select “Drive setting” mode. “Drive”
appears on the screen.
LDB 0
4. Set the color analyzer at the CHROMA mode and
zero point calibration. Bring the optical receptor
pointing at the center of the LCD-Panel.
11. Press [4] button to select the “LDR” for Low Drive
To avoid interference from ambient Red adjustment (“LDR” appears on the screen.)
light, this adjustment should be and press [CH + or -] buttons to adjust the color
performed in a dark room. temperature.
Perpendicularity 12. If necessary, adjust the “LDB” or “LDR” again.
13. Press [VOL -] button to shift to the “Debugging
Message” mode.
If there is no message under “[WB]” section, this
adjustment completes.
If “Drive settings are NG. Retry.” is displayed,
Color Analyzer repeat above steps from 5. to 12. Then check
“Debugging Message” again. If “Drive settings are
NG. Retry.” is displayed, replace the LCD Panel or
Note: The optical receptor must be set Digital Main CBA.
perpendicularly to the LCD Panel surface. 14. To cancel or to exit from the White Balance
5. Press [3] button to select the “HDB” for High Drive Adjustment, press [PREV CH] button.
Blue adjustment. (“HDB” appears on the screen.)
5-6 A17FG_HEA
HOW TO INITIALIZE THE LCD TV
The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to
select a language and program channels after the set has been initialized.
To put the program back at the factory-default, initialize the LCD TV using the following procedure.
6-1 A17F6INT
FIRMWARE RENEWAL MODE
Equipment Required 4. The update will start and the following will appear
on the screen.
a. USB storage device
"*" differs depending on the models.
b. Remote Control Unit Software Upgrade
Rear Cabinet
7-1 PL11.0FW
TROUBLESHOOTING
[ Power Supply Section ]
FLOW CHART NO.1
The power cannot be turned on.
No
Is the fuse (F601) normal? See FLOW CHART No.2 <The fuse blows out.>
Yes
Check the presence that the primary component Check the presence that the rectifying diode or circuit
is leaking or shorted and service it if defective. is shorted in each rectifying circuit of secondary side,
and service it if defective.
Does the photocoupler circuit on the No Check IC601, D639, D652, D653, Q631 and their
secondary side operate normally? periphery circuit, and service it if defective.
Yes
Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side,
and service it if defective. (IC631, Q209, Q210, Q211, Q635, Q637, Q640, Q641, Q642, D631, D632, D633, D638, D641,
D642, D646, D647)
Is approximately +35V voltage supplied to the No Check C638, D638, D639 and their periphery
cathode of D638? circuit, and service it if defective.
Yes
8-1 PL11.0TR
FLOW CHART NO.6
LCD+31.5V is not output.
No
Is approximately +35V voltage supplied to the collector See FLOW CHART No.5<AL+33V is not output>
of Q210?
Yes
No
Is approximately +16V voltage supplied to the Check C631, D631, D635 and their periphery circuit,
collector of Q209? and service it if defective.
Yes
No
Is approximately +13.5V voltage supplied to the Check Q207, Q208, D203, D204, D211, P-ON-H1 line
base of Q209? and their periphery circuit, and service it if defective.
Yes
Replace Q209.
No
Is approximately +7V voltage supplied to the Check C644, D646 and their periphery circuit,
cathode of D646? and service it if defective.
Yes
8-2 PL11.0TR
FLOW CHART NO.9
P-ON+5V is not output. (LCD+13V is outputted normally.)
No
Is approximately +6.5V voltage supplied to the See FLOW CHART No.8 <P-ON+7V is not output.>
collector of Q641?
Yes
No
Is approximately +6V voltage supplied to the Check D645 and their periphery circuit, and service
base of Q641? it if defective.
Yes
Replace Q641.
No
Is approximately +6.5V voltage supplied to the See FLOW CHART No.8 <P-ON+7V is not output.>
collector of Q640?
Yes
No
Is approximately +6V voltage supplied to the Check D645 and their periphery circuit, and service
base of Q640? it if defective.
Yes
Replace Q640.
Is approximately +13V voltage supplied to the No Check C639, D641, D642 and their periphery circuit,
cathode of D641 and D642? and service it if defective.
Yes
Check for short-circuiting or leak on the load circuit,
and service it if defective.
No
Is approximately +3V voltage supplied to the Check C645, D647 and their periphery circuit, and
cathode of D647? service it if defective.
Yes
Check for short-circuiting or leak on the load circuit,
and service it if defective.
8-3 PL11.0TR
FLOW CHART NO.13
P-ON+3.3V is not output.
No
Is approximately +4.5V voltage supplied to the Check C633, D633 and their periphery circuit, and
cathode of D633? service it if defective.
Yes
No
Is the "H" signal (approximately +3.5V) inputted to the Check Q638, Q639, D666, P-ON-H2 line and their
base of Q637? periphery circuit, and service it if defective.
Yes
Replace Q637.
No
Is approximately +13.5V voltage supplied to the See FLOW CHART No.11 <AL+13V is not output.>
collector of Q642?
Yes
No
Is approximately +10V voltage supplied to the Check D670 and their periphery circuit, and service
base of Q642? it if defective.
Yes
Replace Q642.
No
Is approximately +35V voltage supplied to the See FLOW CHART No.5 <AL+33V is not output.>
collector of Q635?
Yes
No
Is approximately +5V voltage supplied to Pin(3) of Check Q635, D659 and their periphery circuit, and
IC631? service it if defective.
Yes
Replace IC631.
No
Is approximately -6.5V voltage supplied to the Check C632, D632 and their periphery
anode of D632? circuit, and service it if defective.
Yes
No
Is approximately -6V voltage supplied to the Check Q207, Q208, D208, D210, P-ON-H1 line and
base of Q211? their periphery circuit, and service it if defective.
Yes
Replace Q211.
8-4 PL11.0TR
[ Video Signal Section ]
FLOW CHART NO.1
The key operation is not functioning.
No
Are the contact point and installation state of the key Re-install the switches (SW101B, SW103B~SW107B)
switches (SW101B, SW103B~SW107B) normal? correctly or replace the poor switch.
Yes
No
When pressing each switches (SW101B, SW103B~ Check the switches (SW101B, SW103B~SW107B)
SW107B) do the voltage of Pin(29) of CN302 decrease? and their periphery, and service it if defective.
Yes
Replace Digital Main CBA Unit.
No
Is 3.3V voltage supplied to Pin(2) terminal of the Check AL+3.3V line and service it if defective.
remote control receiver (RS101)?
Yes
No
Is the "L" pulse sent out Pin(1) terminal of remote Replace the remote control receiver(RS101)
control receiver (RS101) when the infrared remote or the remote control unit.
control is activated?
Yes
No
Is the "L" pulse supplied to Pin(25) of CN301? Check the line between Pin(1) terminal of remote
Yes control receiver(RS101) and Pin(25) of CN301,
and service it if defective.
Replace Digital Main CBA Unit.
No
Are the video signal inputted to Pin(4) of CN302? Check the line between Pin(4) of CN302 and
Yes JK752, and service it if defective.
8-5 PL11.0TR
FLOW CHART NO.4
Picture does not appear normally.(Tuner input)
No
Are the DIF signal inputted to the Pin(26,28) of CN302? Check TU301 and their periphery circuit,
Yes and service it if defective.
No
Are the video signal outputted to the Pin(6, 8) of Check the line between Pin(6, 8) of CN302 and
CN302? JK751, and service it if defective.
Pin(6): S-VIDEO-C
Pin(8): S-VIDEO-Y
Yes
No
Are the video signal inputted to the Pin(15, 17, 19) of Check the line between Pin(15, 17, 19) of CN302
CN302? and input terminals(JK731, JK732, JK733), and
Pin(15): VIDEO-Y service it if defective.
Pin(17): VIDEO-Pb
Pin(19): VIDEO-Pr
Yes
8-6 PL11.0TR
[ Audio Signal Section ]
FLOW CHART NO.1
Audio is not outputted normally.(Audio input)
No
Are the audio(L/R) signals inputted to Pin(2, 15) Check the line between Pin(2, 15) of IC771 and
of IC771? input terminal(JK753, JK754), and service it if
defective.
Yes
No
Are the audio(L/R) signals inputted to each pin of Replace Digital Main CBA Unit.
CN301?
Pin(6) : AMP(L)-OUT
Pin(8) : AMP(R)-OUT
Pin(2) : AUDIO(L)-OUT
Pin(4) : AUDIO(R)-OUT
Yes
Are the audio(L/R) signals inputted to the Pin(3, 40) No Check the line between Pin(6, 8) of CN301 and
of IC801? Pin(3, 40) of IC801, and service it if defective.
Are the audio(L/R) signals inputted to the Pin(3, 5) No Check the line between Pin(2, 4) of CN301 and
of IC871? Pin(3, 5) of IC871, and service it if defective.
Yes
Are the audio(L/R) signals outputted to the Pin(1, 2) No
Check IC801 and their periphery circuit, and
of CN801 and CN802? service it if defective.
CN801: SP(L) Yes
CN802: SP(R) Check SP801,SP802 and their periphery circuit,
and service it if defective.
Are the audio(L/R) signals outputted to the audio
output terminal?
No Check the line between Pin(1, 7) of IC871 and audio
JK871: AUDIO(L)-OUT output terminal(JK871, JK872), and service it if
JK872: AUDIO(R)-OUT defective.
8-7 PL11.0TR
FLOW CHART NO.2
Audio is not outputted normally.(Component Audio input)
No
Are the audio(L/R) signals inputted to the Pin(4, 11) Check the line between Pin(4, 11) of IC771 and
of IC771? input terminal(JK741, JK742), and service it if
Yes defective.
No
Are the audio(L/R) signals inputted to each pin of Replace Digital Main CBA Unit.
CN301?
Pin(6) : AMP(L)-OUT
Pin(8) : AMP(R)-OUT
Pin(2) : AUDIO(L)-OUT
Pin(4) : AUDIO(R)-OUT
Yes
Are the audio(L/R) signals inputted to the Pin(3, 40) No Check the line between Pin(6, 8) of CN301 and
of IC801? Pin(3, 40) of IC801, and service it if defective.
Are the audio(L/R) signals inputted to the Pin(3, 5) No Check the line between Pin(2, 4) of CN301 and
of IC871? Pin(3, 5) of IC871, and service it if defective.
Yes
Are the audio(L/R) signals outputted to the Pin(1, 2) No
Check IC801 and their periphery circuit, and
of CN801 and CN802? service it if defective.
CN801: SP(L) Yes
CN802: SP(R) Check SP801,SP802 and their periphery circuit,
and service it if defective.
Are the audio(L/R) signals outputted to the audio
output terminal?
No Check the line between Pin(1, 7) of IC871 and audio
JK871: AUDIO(L)-OUT output terminal(JK871, JK872), and service it if
JK872: AUDIO(R)-OUT defective.
8-8 PL11.0TR
FLOW CHART NO.3
Audio is not outputted normally.(Tuner input)
No
Are the DIF signals outputted to the Pin(26, 28) Check TU301 and their periphery circuit, and
of CN302? service it if defective.
Yes
No
Are the audio(L/R) signals inputted to each pin of Replace Digital Main CBA Unit.
CN301?
Pin(6) : AMP(L)-OUT
Pin(8) : AMP(R)-OUT
Pin(2) : AUDIO(L)-OUT
Pin(4) : AUDIO(R)-OUT
Yes
Are the audio(L/R) signals inputted to the Pin(3, 40) No Check the line between Pin(6, 8) of CN301 and
of IC801? Pin(3, 40) of IC801, and service it if defective.
Are the audio(L/R) signals inputted to the Pin(3, 5) No Check the line between Pin(2, 4) of CN301 and
of IC871? Pin(3, 5) of IC871, and service it if defective.
Yes
Are the audio(L/R) signals outputted to the Pin(1, 2) No
Check IC801 and their periphery circuit, and
of CN801 and CN802? service it if defective.
CN801: SP(L) Yes
CN802: SP(R) Check SP801,SP802 and their periphery circuit,
and service it if defective.
Are the audio(L/R) signals outputted to the audio
output terminal?
No Check the line between Pin(1, 7) of IC871 and audio
JK871: AUDIO(L)-OUT output terminal(JK871, JK872), and service it if
JK872: AUDIO(R)-OUT defective.
8-9 PL11.0TR
IC3301 RS101
(MAIN MICRO CONTROLLER) P-ON+9V REMOTE
SENSOR
[TYPE A]
D101
CN101 CL102B POWER
2 REMOTE 2
5 P-ON+9V 5
4 KEY-IN1 4
CN3702 CN302
KEY-IN1 AC5 29 KEY-IN1 29
INPUT0
TO AUDIO E1 INPUT0
INPUT1
BLOCK E2 INPUT1
DIAGRAM AUDIO-MUTE
AB9 AUDIO-MUTE P-ON-H2
P-ON-H1 TO
CN3701 CN301 POWER SUPPLY
PROTECT1
PROTECT1 AD5 11 PROTECT1 11 BLOCK DIAGRAM
PROTECT2
PROTECT2 AD4 15 PROTECT2 15
1. System Control Block Diagram
9-1
BACKLIGHT-SW AB16 BACKLIGHT-SW INVERTER
26 BACKLIGHT-SW 26 5
BLOCK
BACKLIGHT-ADJ AB23 28 BACKLIGHT-ADJ 28 4 BACKLIGHT-ADJ DIAGRAM
DRIVE 14 VCOM (CN1001)
IC201,Q203,
Q204,Q205
Either TU301 is used for Power Supply CBA.
* TU301 (TUNER UNIT)
CN3702 CN302
SCL AC18 22 SCL 22 9 SCL
SDA AC19 21 SDA 21 8 SDA
BLOCK DIAGRAMS
IC3101 (MEMORY)
* TU301 (TUNER UNIT)
SCK 6 AB25 SCK
SI 5 AB24 SIN 4 SCL
SO 2 AC25 SOUT 5 SDA
CS 1 AC24 CS
WP 3 E11 WP
X3101
25MHz N1 CLKIN
OSC N2 CLKOUT
PL11.0ABLS
VIDEO SIGNAL AUDIO SIGNAL
JK752
VIDEO-IN
WF2 WF3 WF1
CL701B CL701A CN302 CN3702
VIDEO-IN
5 VIDEO-IN 5 4 VIDEO-IN 4
S-VIDEO-C-IN
3 S-VIDEO-C-IN 3 6 S-VIDEO-C-IN 6
C Y S-VIDEO-Y-IN
JK751 1 S-VIDEO-Y-IN 1 8 S-VIDEO-Y-IN 8
S-VIDEO-SW
S-VIDEO 2 S-VIDEO-SW-IN 2 5 S-VIDEO-SW 5
-IN COM-VIDEO-Y-IN
15 COM-VIDEO-Y-IN 15
COM-VIDEO-Pb-IN
17 COM-VIDEO-Pb-IN 17
COM-VIDEO-Pr-IN
19 COM-VIDEO-Pr-IN 19
TO DIGITAL
JK731 SIGNAL PROCESS
COMPONENT BLOCK DIAGRAM
-Y-IN
JK732
COMPONENT
-Pb-IN
JK733
COMPONENT
-Pr-IN
9-2
Either TU301 is used for Power Supply CBA.
* TU301
(TUNER UNIT)
CN302 CN3702
DIF-OUT1
DIF-OUT1 13 26 DIF-OUT1 26
DIF-OUT2
DIF-OUT2 12 28 DIF-OUT2 28
IF-AGC
IF-AGC 14 24 IF-AGC 24
* TU301
(TUNER UNIT)
DIF-OUT1 11
DIF-OUT2 10
IF-AGC 9
PL11.0BALV
AUDIO SIGNAL
CL701B CL701A
JK753 7 AUDIO(L)-IN 7
AUDIO(L) 9 AUDIO(R)-IN 9
-IN
JK754 IC771
AUDIO(R) (AUDIO SELECTOR)
-IN
2
JACK CBA 4
1 3
5
JK741 15
COMPONENT- 11
AUDIO(L)-IN 13
12
JK742
COMPONENT- 14 WF7 TO
AUDIO(R)-IN CN302 CN3702 DIGITAL
AUDIO(L) SIGNAL
3. Audio Block Diagram
13 AUDIO(L) 13
CONTROL AUDIO(R) PROCESS
LOGIC 11 AUDIO(R) 11 BLOCK
DIAGRAM
9 10 CN302 CN3702
Q771 INPUT1 TO
JK721 10 INPUT1 10 SYSTEM
INPUT0 CONTROL
HDMI- 12 INPUT0 12
AUDIO-MUTE BLOCK
AUDIO(L)-IN DIAGRAM
Q772
JK722
HDMI-
AUDIO(R)-IN IC3802 IC3803
IC871 (D/A CONVERTER)
(OP AMP) (AUDIO DSP)
LRCLK
CN301 CN3701 8 35 2
9-3
(L-CH) BCLK
JK871 1 3 2 AUDIO(L)-OUT 2 15 D/A 7 36 40
AUDIO(L)-OUT (R-CH) CONVERTER ADATA1
4 AUDIO(R)-OUT 4 14 6 33 DSP 4
ACLK
6 AMP(L)-OUT 6 5 37 39
JK872 7 5 ADATA0
AUDIO(R)-OUT Q871 8 AMP(R)-OUT 8 34 3
TO
MUTE IC3801 DIGITAL
Q872 Q873,Q874 (D/A CONVERTER) SIGNAL
MUTE DRIVE PROCESS
CN302 CN3702 8 BLOCK
JK841 (L-CH) DIAGRAM
DIGITAL BUFFER 2 SPDIF 2 15 D/A 7
(R-CH) CONVERTER
AUDIO-OUT Q841 20 AUDIO-MUTE 20 14 6
(COAXIAL) IC801 (AUDIO AMP) 5
PWM
8 GENERATOR
GAIN 3
PWM CONTROL SPDIF
15 GENERATOR
PWM
36 GENERATOR
CL801 CN801 GAIN 40
SP801 PWM CONTROL
SP(L)+ 2 28 GENERATOR
SPEAKER
L-CH SP(L)- 1
CONTROL LOGIC
4
Q801
CL802 CN802
SP802 SP(R)+ 2
SPEAKER SP(R)- 1
R-CH
PL11.0ABLA
VIDEO SIGNAL AUDIO SIGNAL
LCD MODULE
ASSEMBLY
IC3301 (DIGITAL SIGNAL PROCESS) IC3901 (TINING CONTROLLER)
DIGITAL MAIN CBA UNIT
CN3902
VIDEO-IN 48 23 LLV0(+)
AA3
S-VIDEO-C-IN 47 22 LLV0(-)
V3
TO VIDEO S-VIDEO-Y-IN 46 21 LLV1(+)
U3 A/D
BLOCK DIAGRAM COM-VIDEO-Y-IN SW 45 20 LLV1(-)
U1 CONVERTER
COM-VIDEO-Pb-IN 44 19 LLV2(+)
V1
COM-VIDEO-Pr-IN DATA 43 18 LLV2(-)
U2
PROCESSING 38 13 LLV3(+)
V2
GAMMA 37 12 LLV3(-)
CORRECTOR LVDS 36 11 LLV4(+)
DIF-OUT1 OUTPUT 35 10 LLV4(-)
AE2 DEMODULATOR FRC
DIF-OUT2 34 9 LLV5(+)
TO VIDEO AF2 /MPEG DECODER LINE BUFFER
BLOCK DIAGRAM IF-AGC 33 8 LLV5(-)
AF7 IF-AGC 42 16 LLVCLK(+)
S-VIDEO-SW
C6 S-VIDEO-SW 41 15 LLVCLK(-)
63 6 TP
64 5 POL
AUDIO(L) 30 4 CPV
M1
AUDIO(R) 31 3 OE1
M2
BCLK 32 1 STV
AD9
TO AUDIO LRCLK
BLOCK DIAGRAM AD12
ACLK AUDIO I/F
AD10
SPDIF
AD11
ADATA0
AC10
ADATA1 AD23 8
JK3701 AD14
AD24 7
LVDS TX
TMDS-D0(+) AE23 10
7 A9
TMDS-D0(-) AF23 9
9 B9
TMDS-D1(+) AF22 12 LVDS DATA
4 C8 RX INPUT
TMDS-D1(-) AE22 11
6 C9 LATCH
TMDS-D2(+) AUDIO AD21 16
9-4
1 B8 DECODER DIGITAL
HDMI-IN1 TMDS-D2(-) AD22 15
3 A8 SIGNAL
TMDS-CLOCK(+) PROCESS AF24 14
10 B10
TMDS-CLOCK(-) AE24 13
12 A10
SDA
4. Digital Signal Process Block Diagram
16 A11
SCL
15 B11
JK3702 TP W25
POL W23
TMDS-D0(+)
7 A5 CPV Y24
TMDS-D0(-)
9 B5 OE Y23
TMDS-D1(+)
4 C4 STV Y22
TMDS-D1(-) HDMI
6 C5
TMDS-D2(+) I/F
HDMI-IN2 1 B4
TMDS-D2(-)
3 A4
TMDS-CLOCK(+)
10 B6
TMDS-CLOCK(-)
12 A6
SDA IC3201
16 A7 (DDR2 SDRAM)
SCL
15 B7
A13-15,A18, B1,B9,C2,C8,
VIDEO A21-23,B13-15, D1,D3,D7,D9,
JK3704 F1,F9,G2,G8, DATA(0-15)
DECODER B17,B19-23
TMDS-D0(+) H1,H3,H7,H9
7 B1 C15,C17-19, M2,M3,M7,M8,
TMDS-D0(-)
9 B2 C23,C24,D14, N2,N3,N7,N8, ADDESS(0-12)
TMDS-D1(+) D15,D17-19, P2,P3,P7,P8,R2
4 C1 D22,D23
TMDS-D1(-)
6 C2
TMDS-D2(+)
HDMI-IN3 1 D1
TMDS-D2(-)
3 D2
TMDS-CLOCK(+)
10 A1
TMDS-CLOCK(-)
12 A2
SDA
16 A3
SCL
15 B3
PL11.0ABLD
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
INVERTER CBA
T1950
TO CN1901 CN1100
POWER 1 +B 2 10 1 BACK
SUPPLY T1100
3 HOT-GND 2 LIGHT
BLOCK 3 11
DIAGRAM 4 HOT+15V 2 8
(CN602) 4 4 7
7 14 1 6
3 5
8 15
Q1930
IC1200
SWITCHING (PWM CONTROL)
Q1300 Q1303
IC1930 (FEED BACK)
+10.5V REG. 7 STB
4 1
Q1700
5. Inverter Block Diagram
9-5
16 2
Q1703
COLD SWITCHING
CN1102
PROTECT
T1102 1 BACK
2 LIGHT
2 8
13 18
4 7
Q1971 Q1972
1 6
3 5
CN1001
TO 10 PROTECT3
SYSTEM 11 BACKLIGHT-SW
CONTROL
BLOCK 12 BACKLIGHT-ADJ
DIAGRAM 2 VCOM
(CN201)
Q1202
CN1003
10 VCOM
LCD MODULE
ASSEMBLY
PL11.0ABLINV
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. NOTE:
CAUTION ! : For continued protection against risk of fire,
If Main Fuse (F601) is blown , check to see that all components in the power supply The voltage for parts in hot circuit is measured using
replace only with same type 4 A, 125V fuse.
circuit are not defective before you connect the AC plug to the AC power supply. 4A/125V hot GND as a common terminal.
Otherwise it may cause some components in the power supply circuit to fail.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
12
CN301 CN3701 DIGITAL MAIN CBA UNIT
4A/125V 10 P-ON+3V 10 P-ON+3V
Q207,Q208 16 P-ON+7V 16 P-ON+7V
CN602 4 13 SWITCHING 21,22 AL+3.3V 21,22 AL+3.3V
TO
INVERTER 1 +B 19,20 P-ON+3.3V 19,20 P-ON+3.3V
BLOCK 2 HOT-GND 13,14 P-ON+5V 13,14 P-ON+5V
DIAGRAM
(CN1901) 3 HOT+15V
Q603, 14 Q401
Q604
SW
HOT+15V Q209, Q213,
15 D204
6. Power Supply Block Diagram
5 SW+13V
16
9-6
7
17
Q601 8 Q642
18
SWITCHING SW+9V P-ON+9V
AL+33V
Q602 P-ON+5V
SWITCHING 9 19 AL+13V
TUNER+5V
AL+3.3V
IC601 P-ON-H1
ERROR Q637,D666 TO SYSTEM
IC602 P-ON-H2
VOLTAGE DET SW+3.3V CONTROL
SWITCHING PROTECT1 BLOCK
CONTROL 4 1 PROTECT2 DIAGRAM
Q638,Q639
VH 8
3 2 SWITCHING
ZCD 1 Q631,
OUT 5 D653
FB 4 FEED
IS 3 BACK
VCC 6
Q640
SW+5V
Q634
Q641,Q643
SW+5V
Q636
IC631
Q635
+3.3V
+5V REG. 3 2
REG.
HOT COLD
POWER SUPPLY CBA
PL11.0ABLP
RS101
IC3005 P-ON+9V REMOTE
(MAIN MICRO CONTROLLER) SENSOR
[TYPE B]
D101
CN101 CL102B POWER
2 REMOTE 2
5 P-ON+9V 5
4 KEY-IN1 4
CN3006 CN302
KEY-IN1 A15 29 KEY-IN1 29
9-7
BACKLIGHT-SW E2 BACKLIGHT-SW 26 BACKLIGHT-SW INVERTER
26 5
BLOCK
BACKLIGHT-ADJ F3 28 BACKLIGHT-ADJ 28 4 BACKLIGHT-ADJ DIAGRAM
DRIVE 14 VCOM (CN1001)
IC201,Q203,
Q204,Q205
Either TU301 is used for Power Supply CBA.
SCL TO DIGITAL
SIGNAL 4 SCL
SDA PROCESS
BLOCK 5 SDA
DIAGRAM
X3001
25MHz H15 XIN25
OSC H16 XOUT25
PL11.0BBLS
VIDEO SIGNAL AUDIO SIGNAL
JK752
VIDEO-IN
WF2 WF3 WF1
CL701B CL701A CN302 CN3006
VIDEO-IN
5 VIDEO-IN 5 4 VIDEO-IN 4
S-VIDEO-C-IN
3 S-VIDEO-C-IN 3 6 S-VIDEO-C-IN 6
C Y S-VIDEO-Y-IN
JK751 1 S-VIDEO-Y-IN 1 8 S-VIDEO-Y-IN 8
S-VIDEO-SW
S-VIDEO 2 S-VIDEO-SW-IN 2 5 S-VIDEO-SW 5
-IN COM-VIDEO-Y-IN
15 COM-VIDEO-Y-IN 15
COM-VIDEO-Pb-IN
17 COM-VIDEO-Pb-IN 17
COM-VIDEO-Pr-IN
19 COM-VIDEO-Pr-IN 19
TO DIGITAL
JK731 SIGNAL PROCESS
COMPONENT BLOCK DIAGRAM
-Y-IN
JK732
COMPONENT
-Pb-IN
JK733
COMPONENT
-Pr-IN
9-8
Either TU301 is used for Power Supply CBA.
* TU301
(TUNER UNIT)
CN302 CN3006
DIF-OUT1
DIF-OUT1 13 26 DIF-OUT1 26
DIF-OUT2
DIF-OUT2 12 28 DIF-OUT2 28
IF-AGC
IF-AGC 14 24 IF-AGC 24
* TU301
(TUNER UNIT)
DIF-OUT1 11
DIF-OUT2 10
IF-AGC 9
PL11.0BBLV
AUDIO SIGNAL
CL701B CL701A
JK753 7 AUDIO(L)-IN 7
AUDIO(L) 9 AUDIO(R)-IN 9
-IN
JK754 IC771
AUDIO(R) (AUDIO SELECTOR)
-IN
2
JACK CBA 4
1 3
5
JK741 15
COMPONENT- 11
AUDIO(L)-IN 13
12
JK742
COMPONENT- 14 WF7
AUDIO(R)-IN CN302 CN3006 TO DIGITAL
AUDIO(L) SIGNAL
3. Audio Block Diagram
13 AUDIO(L) 13
CONTROL AUDIO(R) PROCESS
LOGIC 11 AUDIO(R) 11 BLOCK
DIAGRAM
9 10 CN302 CN3006
Q771 INPUT1
10 INPUT1 10 TO SYSTEM
JK721 INPUT0 CONTROL
HDMI- 12 INPUT0 12 BLOCK
AUDIO(L)-IN AUDIO-MUTE
DIAGRAM
Q772
JK722
HDMI-
AUDIO(R)-IN IC871
(OP AMP)
CN301 CN3002
9-9
AUDIO(L)-OUT
JK871 1 3 2 AUDIO(L)-OUT 2
AUDIO(L)-OUT AUDIO(R)-OUT
4 AUDIO(R)-OUT 4
AMP(L)-OUT
6 AMP(L)-OUT 6
JK872 7 5 AMP(R)-OUT TO DIGITAL
AUDIO(R)-OUT Q871 8 AMP(R)-OUT 8 SIGNAL
MUTE PROCESS
Q872 Q873,Q874 BLOCK
DIAGRAM
MUTE DRIVE
CN302 CN3006
JK841 SPDIF
DIGITAL BUFFER 2 SPDIF 2
AUDIO-OUT Q841 20 AUDIO-MUTE 20
(COAXIAL) IC801 (AUDIO AMP)
9,10
DRIVE1 PWM1 1
13,14
35,36
DRIVE2 PWM2 44
CL801 CN801 31,32
SP801 SP(L)+ 2
SPEAKER
L-CH SP(L)- 1 MUTE CONTROL
20
Q801
CL802 CN802
SP802 SP(R)+ 2
SPEAKER SP(R)- 1
R-CH
PL11.0BBLA
VIDEO SIGNAL AUDIO SIGNAL
LCD MODULE
DIGITAL MAIN CBA UNIT IC3005 (DIGITAL SIGNAL PROCESS) ASSEMBLY
VIDEO-IN
B9 CN3005
S-VIDEO-C-IN
C8 P14 23 LLV0(+)
S-VIDEO-Y-IN
A10 P13 22 LLV0(-)
COM-VIDEO-Y-IN A/D
C9 SW N16 21 LLV1(+)
COM-VIDEO-Pb-IN CONVERTER
D8 N15 20 LLV1(-)
TO VIDEO COM-VIDEO-Pr-IN
B11 P16 19 LLV2(+)
BLOCK DIAGRAM
C10 P15 18 LLV2(-)
LVDS TX T16 13 LLV3(+)
DIF-OUT1 T15 12 LLV3(-)
A12 DEMODULATOR
DIF-OUT2 R14 11 LLV4(+)
B12 /MPEG DECODER
IF-AGC T14 10 LLV4(-)
A16 IF-AGC R13 9 LLV5(+)
S-VIDEO-SW
N12 S-VIDEO-SW T13 8 LLV5(-)
AUDIO(L) R16 16 LLVCLK(+)
A8
AUDIO(R) R15 15 LLVCLK(-)
B8
AUDIO(L)-OUT TP L13 6 TP
B6
TO AUDIO AUDIO(R)-OUT POL M15 5 POL
A6 AUDIO I/F
BLOCK DIAGRAM SPDIF
N10 CPV L16 4 CPV
AMP(L)-OUT OE L15 3 OE1
B7
AMP(R)-OUT STV M14 1 STV
A7
JK3003 AUDIO
HDMI-IN1 DIGITAL
IC3018 (HDMI SW) DECODER SIGNAL
TMDS-D0(+) PROCESS
7 42
TMDS-D0(-)
9-10
9 41
TMDS-D1(+)
4 45
TMDS-D1(-) 26 B4
6 44
TMDS-D2(+) 27 A4
1 48
4. Digital Signal Process Block Diagram
TMDS-D2(-) 23 B3
3 47
TMDS-CLOCK(+) 24 A3
10 39 HDMI
TMDS-CLOCK(-) 20 B2 I/F
12 38
HDMI-DATA 21 A2
16 36
HDMI-CLOCK HDMI 17 B1
15 37
SW 18 A1
JK3004 JK3002
HDMI-IN2 HDMI-IN3
TMDS-D0(+) TMDS-D0(+) VIDEO
7 57 8 7
TMDS-D0(-) TMDS-D0(-) DECODER
9 56 7 9
TMDS-D1(+) TMDS-D1(+)
4 60 11 4
TMDS-D1(-) TMDS-D1(-)
6 59 10 6
TMDS-D2(+) TMDS-D2(+)
1 63 14 1
TMDS-D2(-) TMDS-D2(-)
3 62 13 3
TMDS-CLOCK(+) TMDS-CLOCK(+)
10 54 5 10 IC3002
TMDS-CLOCK(-) TMDS-CLOCK(-) (DDR2 SDRAM)
12 53 4 12
HDMI-DATA HDMI-DATA
16 51 1 16
HDMI-CLOCK HDMI-CLOCK B1,B9,C2,C8,
15 52 2 15 N4,N7,N8,P3,P4,P6-P8, D1,D3,D7,D9,
R3,R4,R6,R8,T2-T5 F1,F9,G2,G8, DATA(0-15)
IC3011 (EEPROM) H1,H3,H7,H9
2 SCL1 SCL3 10 M2,M3,M7,M8,
H1,H2,J1,J2,J4,K1,K3, N2,N3,N7,N8, ADDRESS(0-12)
3 SDA1 SDA3 11 L1,L2,M1-M3,N1 P2,P3,P7,P8,R2
SCL TO SYSTEM
15 SCL2 SCL0 7
SDA CONTROL
14 SDA2 SDA0 6 BLOCK DIAGRAM
PL11.0BBLD
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
INVERTER CBA
T1950
TO CN1901 CN1100
POWER 1 +B 2 10 1 BACK
SUPPLY T1100
3 HOT-GND 2 LIGHT
BLOCK 3 11
DIAGRAM 4 HOT+15V 2 8
(CN602) 4 4 7
7 14 1 6
3 5
8 15
Q1930
IC1200
SWITCHING (PWM CONTROL)
Q1300 Q1303
IC1930 (FEED BACK)
+10.5V REG. 7 STB
4 1
Q1700
5. Inverter Block Diagram
9-11
16 2
Q1703
COLD SWITCHING
CN1102
PROTECT
T1102 1 BACK
2 LIGHT
2 8
13 18
4 7
Q1971 Q1972
1 6
3 5
CN1001
TO 10 PROTECT3
SYSTEM 11 BACKLIGHT-SW
CONTROL
BLOCK 12 BACKLIGHT-ADJ
DIAGRAM 2 VCOM
(CN201)
Q1202
CN1003
10 VCOM
LCD MODULE
ASSEMBLY
PL11.0BBLINV
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. NOTE:
CAUTION ! : For continued protection against risk of fire,
If Main Fuse (F601) is blown , check to see that all components in the power supply The voltage for parts in hot circuit is measured using
replace only with same type 4 A, 125V fuse.
circuit are not defective before you connect the AC plug to the AC power supply. 4A/125V hot GND as a common terminal.
Otherwise it may cause some components in the power supply circuit to fail.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
12
CN301 CN3002 DIGITAL MAIN CBA UNIT
4A/125V 10 P-ON+3V 10 P-ON+3V
Q207,Q208 16 P-ON+7V 16 P-ON+7V
CN602 4 13 SWITCHING 21,22 AL+3.3V 21,22 AL+3.3V
TO
INVERTER 1 +B 19,20 P-ON+3.3V 19,20 P-ON+3.3V
BLOCK 2 HOT-GND 13,14 P-ON+5V 13,14 P-ON+5V
DIAGRAM
(CN1901) 3 HOT+15V
Q603, 14 Q401
Q604
SW
HOT+15V Q209, Q213,
15 D204
6. Power Supply Block Diagram
5 SW+13V
16
9-12
7
17
Q601 8 Q642
18
SWITCHING SW+9V P-ON+9V
AL+33V
Q602 P-ON+5V
SWITCHING 9 19 AL+13V
TUNER+5V
AL+3.3V
IC601 P-ON-H1
ERROR Q637,D666
IC602 P-ON-H2 TO SYSTEM
VOLTAGE DET SW+3.3V CONTROL
SWITCHING PROTECT1
CONTROL BLOCK
4 1 PROTECT2 DIAGRAM
Q638,Q639
VH 8
3 2 SWITCHING
ZCD 1 Q631,
OUT 5 D653
FB 4 FEED
IS 3 BACK
VCC 6
Q640
SW+5V
Q634
Q641,Q643
SW+5V
Q636
IC631
Q635
+3.3V
+5V REG. 3 2
REG.
HOT COLD
POWER SUPPLY CBA
PL11.0BBLP
SCHEMATIC DIAGRAMS / CBA AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis
have special characteristics. These characteristics
often pass unnoticed and the protection afforded by
them cannot necessarily be obtained by using
replacement components rated for higher voltage,
wattage, etc. Replacement parts that have these
special safety characteristics are identified in this
manual and its supplements; electrical components
having such features are identified by the mark “#” in
the schematic diagram and the parts list. Before
replacing any of these components, read the parts list
in this manual carefully. The use of substitute
replacement parts that do not have the same safety
characteristics as specified in the parts list may create
shock, fire, or other hazards.
Notes:
1. Do not use the part number shown on these
drawings for ordering. The correct part number is
shown in the parts list, and may be slightly
different or amended since these drawings were
prepared.
2. All resistance values are indicated in ohms
(K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless
otherwise specified.
4. All capacitance values are indicated in µF
(P = 10-6 µF).
5. All voltages are DC voltages unless otherwise
specified.
6. This schematic diagrams are masterized version
that should cover the entire PL11.0 chassis models.
Thus some parts in detail illustrated on this
schematic diagrams may vary depend on the
model within the PL11.0 chassis.
Please refer to the parts lists for each models.
7. The Circuit Board layout illustrated on this service
manual is the latest version for this chassis at the
moment of making this service manual.
Depend on the mass production date of each
model, the actual layout of each Board may differ
slightly from this version.
10-1 PL11.0SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON
THE FOLLOWING PAGES:
1. CAUTION:
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME
TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not
defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components
in the power supply circuit to fail.
3. Note:
1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.
1 2 3
(Unit: Volt) 5.0 5.0 Power on mode
10-2 PL11.0SC
Power Supply 1 Schematic Diagram
CAUTION ! NOTE:
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, The voltage for parts in hot circuit is measured using
If Main Fuse (F601) is blown , check to see that all components in the power supply replace only with same type 4 A, 125V fuse. hot GND as a common terminal.
circuit are not defective before you connect the AC plug to the AC power supply. 4A/125V ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
Otherwise it may cause some components in the power supply circuit to fail.
CONTINUE
HOT CIRCUIT. BE CAREFUL. R253 R250 POWER 4
6.8/1/2W 16.8 13.2 8.2/1W
INV+13V
AC601 F601 Q213
AC CORD 4A/125V 2SA950-O LCD+13V
16.2 (SWITCHING) P-ON+3.3V
R601 D631 LCD-5V
2.7M/1/2W SB2150BD
(NO CONNECTION) CN601 4A 125V 16.2 12.9
LCD+31.5V
AC120V 2 R602 C631 R501 R247 R227 Q209 C222 R232
OPEN 1000/25V OPEN 4.7 3.9 2SC2120-Y 470/25V 11K D416 D403 D404 CONTINUE
AC120V 1 /1/2W /1/2W 13.5 (SW+13V) OPEN OPEN POWER 4
C501 R233 C225
SA601 Q501 750 OPEN AUDIO(R)-OUT
SURGE D635 OPEN OPEN
4 ABSORBER
C601
0.22/300V
D621A D621B
WIRE 1ZB200-YBB
R605
2.2/5W
C691
1000P/250V
24BSB-T26
R502
OPEN
(SW+13V)
R254
OPEN
JS201
OPEN
R246
OPEN
R228
2.7K
R229
D211 R231 C221
1.5K 0.01
2.5
0
-0.5
Q401
KTC3198
R405
47K
R245
8.2K D406
15BSB-T26
D405
AUDIO(L)-OUT
CONTINUE
POWER 2
AMP(R)-OUT
D201 2.7K D204 R234 -Y-AT/P R412 AMP(L)-OUT
L601 OPEN KIA431-AT/P 2.2K (SWITCHING) 10K
LINE FILTER R603 C692 D646 TO DIGITAL MAIN
2.2/5W OPEN SB360BH CBA UNIT CN3701
CN301 or CN3002
C644 3.3 1 P-ON-H2
3300/16V R654 2.6 2 AUDIO(L)-OUT
C602 D602 D603 R403 R404 10K
0.22/300V 1N5406-BU 1N5406-BU R651 D643 D644 R410 D203 R411 47K 22K R690 0 3 GND
C693 1 FR104-B 6V2BSB-T26 51K 30K OPEN
L602 1000P/250V 2.6 4 AUDIO(R)-OUT
LINE D601 D604 C637 C642 D401
FILTER 1N5406-BU 1N5406-BU 1500P/2KV 1/50V 3.3 5 PROTECT3
C694
JS601
JS602
JS603
JS604
OPEN
OPEN
OPEN
OPEN
3 R619 R618
WIRE WIRE
D612
FR104-B BC601
BEAD
7
5
14
15
16
FR104-B
D647
SB140
C632
220/25V
0.1
0.7
Q208
0 KTC3198-Y-AT/P
(SWITCHING)
R226
22K
R225
22K
R238
1.5K
31.6
R236
10
R699 R700
0.3 15 PROTECT2
6.9 16 P-ON+7V
0 17 GND
0 18 GND
Q602 C645 R239 D205 OPEN OPEN D676
C223 WIRE
KHB1D0N60D-RTF 17 2200/6.3V R242 D209 OPEN 22/50V 24BSC-T26 3.3 19 P-ON+3.3V
SWITCHING 4 12K 39BSB-T26 D206 3.3 20 P-ON+3.3V
CONTROL 18 R237
124.9 15.2 D641 8.2K 3.3 21 AL+3.3V
SB390
3 19 C683 3.3 22 AL+3.3V
D
2 0
Q601
KTC3198
-GR-AT/P
(SWITCHING)
R623
10K R624
10K
D607A
0
BEAD
D614
FR103-B/P
C650
C650A
0.022
6.1
0.022/100V5.5 Q631
KTC3198
-Y-AT/P
(FEED BACK)
R652
24K
R653
WIRE
D651
OPEN
R655
27K
0
Q634
KTC3199-GR-AT/P
(SWITCHING)
-GR-AT/P
(SWITCHING) 0 C676
2.2/50V
R658
10K
R676
47K
R681
OPEN
D667
OPEN
R408
OE2
P-ON-H1
LCD-P-SAFETY
TK5A50D 10K D409
159.4 G (SWITCHING) D607 0.7 R661
11BSB D622 D653 0 R659 CONTINUE
S 2.8 -T26 R649 R650 390 47K POWER 4
FR103-B/P KIA431 2.7K 2.7K /1/2W
0.1 D -AT/PF5 REMOTE
C606 C606A D652 JS630 D658 C647 D657
D610 R662 OPEN D412 P-ON+9V
1500P 1500P C609 IC631 5V6BSB-T26 15 3V3BSB-T26 R660 33BSB-T26 R687
/100V 47/50V 820 10 AL+3.3V
C607 MM3123DPRE D652A R663 13.4 9.0
330P R611 (+3.3V REG.) 0 820
/2KV 4.7K Q642 C656
R664 9.7 KTC3198-Y-AT/P CONTINUE
VOUT
1 C613
33P
1.0 1 ZCD
0.6 2 FB
0.1 3 IS
VH 8 155.3
NU 7
VCC 6 15.2
D617 R610
FR103-B/P 10
R635
3.9/
1/2W
R636
3.9/
1/2W
D673
OPEN
R696
2.7/1W
R697
2.7/1W
OPEN 3V9BSB-T26
R686
1K
(SW+5V)
R685
22
R641
1.1K
R642
10K
C654
220/10V CONTINUE
POWER 3
P-ON+3.3V
P-ON+9V
C614 R609 P-ON+5V
0 4 GND 180 C658
0.022 OUT 5 3.3 100/10V C649
0.1
C648
100/10V D664
4V7BSB-T26 C655 D415 RESET
C611 D611 OPEN D645 R643
0.1 OPEN C643 KIA431B-AT/P 10K CONTINUE
C615 1 POWER 2
3300P
HOT COLD POWER SUPPLY CBA AL+33V
TUNER+5V
A B C D E F
10-3 PL11.0SCP1
Power Supply 2 Schematic Diagram
DIF-OUT2
DIF-OUT1
DIF-OUT2
DIF-OUT1
CONTINUE
IF-AGC
IF-AGC
POWER 1
+32V
+32V
VCC
GND
SDA
SCL
VCC
SCL
SDA
+5V
AL+33V
NU
NU
NU
NU
NU
NU
NU
NU
NU
NU
NU
NU
NU
NU
TUNER+5V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 1 2 3 4 5 6 7 8 9 10 11
CONTINUE
POWER 3
4 SCL
SDA
IF-AGC
R303
0
R301
OPEN R306
0
JS303
DIF-OUT2 D302 C308
R302 OPEN 47P R307
DIF-OUT1 0 0
AUDIO-MUTE
D301 C307 R305
BC301 OPEN 47P OPEN
WIRE JS302 R310
0
JS301 C304 C306 C305
R311 OPEN OPEN 1/50V 0.1
L301 OPEN
WIRE
C302 C303 C301 D303
C310 L302 R304 R309 C309 0.1 330 OPEN OPEN
47P 0.22uH OPEN 82 0.1 /10V
C311 L303 R308
47P 0.22uH 82
CONTINUE
POWER 1
AL+3.3V
AL+13V D806 R805 R819
22K
3 PROTECT1
P-ON-H1
OPEN OPEN
C830
BC805 OPEN
CL802 CN802 BEAD
SP802 SP(R)- 1
SPEAKER C829
R-CH SP(R)+ 2 1
C845 C846 BC804 C828
470P 470P D804 D803 BEAD 1 L803
20BSB-T26 20BSB-T26 33uH
C836 R815 C815 R810
C823 D807 0.47 22K 1/50V 0 C821 C822 L804 C825 C826 C827
1000/25V OPEN R804 0.1 1000P 33uH 0.1 1000P 10/50V
C837 OPEN
220P R816 R894
47K 47K
C819 10/50V C820 C824
0.47 0.47
C817 1 R811 R812
0 0
C816 10/50V
9.9 2.5 2.5 2.5 4.9 0 5.7 13.5 15.0 0 0 15.0 13.5 0 5.7 0 4.8 0 0
42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22
AVCC
VREF
HBA2
HBB2
RREF
NU
NU
NU
NU
2 GAIN
CONTROL
PWM
GENERATOR
PWM
GENERATOR
IC801
R2A15124FP ATT CONTROL
(AUDIO AMP) LOGIC
GAIN
CONTROL
PWM PWM
GENERATOR GENERATOR OSC
HBA1
HBB1
DVDD
GND
NU
NU
NU
NU
VD
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
CONTINUE 0 2.5 2.5 5.5 3.2 0 0 5.6 13.5 14.9 0 0 14.9 13.5 5.6 0 2.3 2.9 13.5 10.0 R817
POWER 1 10K
AMP(R)-OUT C834 R813 C801 R801 C831 R807 R808
0.47 22K 1/50V 0 10/50V 0 OPEN
AMP(L)-OUT
C835 R814 C814 C818 C832 R809
220P 47K 1 0.1 OPEN 4.7K
C803 C806
0.47 0.47 R818
5.5 10K
0.1
1 R647
1K
C811 L801
C804
0.1
C805
1000P
L802
R802
22K
R803
OPEN
C807
0.1
C808
1000P 0 Q801
KTC3198
-Y-AT/P
(AUDIO-MUTE)
R820
47K
G H I J K L
10-4 PL11.0SCP2
Power Supply 3 & Jack Schematic Diagram
4 DIGITAL
AUDIO-OUT
(COAXIAL)
JK841
C841 R842
1
R841
OPEN
0
R844
220
R843
110
KTC3198-Y-AT/P
(BUFFER)
R845
OPEN
R848
4.7K
CONTINUE
POWER 1
P-ON+3.3V
P-ON+9V
C773 C772 C771 R771 P-ON+5V
OPEN 0.1 100/16V WIRE
IC771 RESET
R778 R788 R789 R790 R791 TC4052BF(ELNF) R772 R773 R780 R781 R782 R783
100K OPEN OPEN OPEN OPEN (AUDIO SELECTOR) 10K 10K OPEN OPEN OPEN OPEN
R713 C703 R776
OPEN OPEN 2.3 1 VDD 16 9.0 100K
R711 R715 C701
OPEN OPEN OPEN 4.5 2 15 4.5 R763
10K
4.5 3 14 0.2
JK711 R714 C704 0.2 4 13 4.5
OPEN OPEN CONTINUE
PC-AUDIO-IN 0.2 5
R712 R716 C702 12 2.3 POWER 4
OPEN OPEN OPEN KEY-IN1
C776 R779 R792 R793 R794 R795 0 6 INH
100P 100K OPEN OPEN OPEN OPEN 11 0.2 AUDIO-MUTE
0 7 VEE R784 R785 R786 R787 R777 C775
SW 10 0 OPEN OPEN OPEN OPEN 100K 100P
0 8 GND CTL
R723 C723 9 9.0
JK721 15K 2.2
HDMI-
AUDIO(L)-IN R721 R725 C721
3 HDMI-
AUDIO(R)-IN
JK722
OPEN
R722
R724
15K
39K
R726
OPEN
C724
2.2
C722
OPEN 39K OPEN
0 R774
0.7 10K
R743 C743 0 Q771
JK741 15K 2.2 KTC3198-Y-AT/P
COMPONENT- (INVERTER)
AUDIO(L)-IN R741 R745 C741 TO DIGITAL MAIN
OPEN 39K OPEN CBA UNIT CN3702
R744 C744 9.0 R775 CN302 or CN3006
JK742 15K 2.2 0 10K 0 1 GND
COMPONENT- 1.7 2
AUDIO(R)-IN R742 R746 C742 0 Q772 SPDIF
OPEN 39K OPEN KTC3198-Y-AT/P 0 3
(INVERTER) WF1 GND
0 4 VIDEO-IN
3.4 5 S-VIDEO-SW
0 6 S-VIDEO-C-IN
R734 C734
JK731 10 0 0 7 GND
COMPONENT R731
WF3 0 8
-Y-IN C731 75 S-VIDEO-Y-IN
39P 0 9
R735 C735 WF2 GND
JK732 10 0 3.3 10 INPUT1
COMPONENT 4.5 11
-Pb-IN C732 R732 AUDIO(R)
2 COMPONENT
-Pr-IN
JK733
39P
C733
39P
75
R733
75
R736
10
C736
0
WF7 WF4
0 12
4.5 13
0 14
INPUT0
AUDIO(L)
GND
0 15 COM-VIDEO-Y-IN
WF5 0 16 GND
0 17 COM-VIDEO-Pb-IN
WF6 0 18 GND
0 19 COM-VIDEO-Pr-IN
0 20 AUDIO-MUTE
JK751 3.3 21 SDA
S-VIDEO-IN R756 C754 CL701B CL701A 3.3 22
C Y 0 0 SCL
1 S-VIDEO-Y-IN 1 3.3 23 RESET
C751 R751 2 S-VIDEO-SW 2 0 24
SW OPEN 75 IF-AGC
3 S-VIDEO-C-IN 3 0 25 GND
R757 C755
0 0 4 GND 4 1.0 26 DIF-OUT1
5 VIDEO-IN 5 0 27 GND
C752 R752
OPEN 75 6 GND 6 0.2 28 DIF-OUT2
7 AUDIO(L)-IN 7 3.3 29 KEY-IN1
R758 C756 8 GND 8
JK752 0 0
VIDEO-IN 9 AUDIO(R)-IN 9 CONTINUE
C753 R753
1 AUDIO(L)-IN
JK753
R754
R759
15K
OPEN 75
R761 C761
C757
2.2
SCL
SDA
IF-AGC
POWER 2
M N O P Q R
10-5 PL11.0SCP3
Power Supply 4 Schematic Diagram
CONTINUE
POWER 1
INV+13V POWER SUPPLY CBA
LCD+13V
P-ON+3.3V
LCD-5V
CONTINUE
LCD+31.5V POWER 1
PROTECT3
BACKLIGHT-SW
4 C201
0.1
R210
10 C217
0.1 R218
BACKLIGHT-ADJ
VCOM-PWM
OE2
10K P-ON-H1
C216 12.9 LCD-P-SAFETY
1000P 5.4
Q203
KTC3198-Y-AT/P 5.3 R211 R208
(V-COM DRIVE) 0 1
3 LCD+13V
VGH
GND
9
10
11
(COMPARATOR)
1 2 3 4
VEE
0.2 0.2 0 0
0 Q205
KTC3198-Y-AT/P
(V-COM DRIVE)
P-ON+3.3V 12
LCD-5V 13 R209
0
VCOM 14 R821
R203 OPEN
GND 15 C675 OPEN
C202 C203
0.1 0.1 OPEN
R887
3.4 22K
29.0 31.2 R888
3.4 1K
Q201 R201 C206 D202 C204 CONTINUE
C208 C209 R205 R204 KTA1267-GR-AT/P 30.4 100K OPEN Q873 POWER 3
OPEN OPEN OPEN 560 (SWITCHING) 1SS133 2.2/50V -2.3 Q874 KTC3198-Y-AT/P
KTA1267 3.4 (SWITCHING) R893 KEY-IN1
JS202 -GR-AT/P 22K
(MUTE DRIVE) 0.1 AUDIO-MUTE
R249 0.4 R248 0
R202 OPEN 10K
1K 1.0
2 REMOTE
P-ON+9V
AL+3.3V
L871
WIRE
C879
0.1
C880
100/16V
R873
100K
R877
1K
0
C871
3300P
Q871
-2.3 KTC3198-Y-AT/P
R896 (AUDIO-MUTE)
TO IR SENSOR 0 0
CBA CL102B CN101 C874 R876 R872
2.2 0 560 JK872
GND 1 AUDIO(R)
REMOTE 2 R892 33K -OUT
R874 C872
AL+3.3V 3 C876 47P R880 100K 3300P
16K
KEY-IN1 4 C885 0
2.2 R878
P-ON+9V 5 1K -2.3 Q872
KTC3198-Y-AT/P
R882 (AUDIO-MUTE)
9.0 4.5 4.5 4.5 100 0
8 7 6 5
IC871 VCC
NJM4558M(TE2) R886
(OP AMP) GND 100K
C883
1 2 3 4 1K
4.5 4.5 4.5 0 R884 C878
R885 1000P CONTINUE
100K 100K POWER 1
R881 C882 AUDIO(R)-OUT
100 1K
1 R891 33K
C875 47P
R883
100K
C877
1000P
AUDIO(L)-OUT
R879
16K
C884
2.2
S T U V W X
10-6 PL11.0SCP4
Inverter Schematic Diagram
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
4 R1951
OPEN
R1952 BC1930
OPEN BEAD
R1941
OPEN
R1942
OPEN
3
4
11
D1990
SB3150BH
D1991
C1993
2200
/35V
C1994 D1994
2200 1ZB30BB
/35V
C1304
220/35V C1305
0.1
C1700
2200/35V
C1701
2200/35V R1301
47K
R1302
23.8
D Q1700
C1702
1
C1104
10P/6.3KV
C1105
R1100
39K
C1118
R1101
0
D1503
DAN202U
2
BACK
LIGHT
SB3150BH R1972 R1305 51K R1700 D1700 TK50P04M1 330P 330P R1102
2.2K
22K 510/2W 100 25.2 G (SWITCHING)
BC1931 D1992 T1100
BEAD SB3150BH S INVERTER R1104 R1105
5 D1701 C1703 R1701 20.9 TRANS R1143 OPEN 100 13
R1300 C1300 15BSB-T26 1000P 10K D1506
R1938 10K 0.1 C1100 2.2 R1103 470 DAN202U
82K R1973 2 8
3.3K
7 14 R1977 R1704 C1101 2.2
20K 4.7/1W 4 7
C1932 R1967 R1967A R1146 OPEN R1107 R1108
0.056 3.9K OPEN R1222 C1705 1 6 100 13
/100V D1973 10 0.022 C1102 2.2
C1970 R1106 470
8 15 2200P 3 5
R1934A R1934 C1103 2.2 R1109 R1110
OPEN 120 20.9 D Q1701 39K 0
R1933A
OPEN
R1933
120 Q1970 R1702 D1702 TK50P04M1 C1116 2.2
R1949 KTC3875S-Y-RTK/P 100 0.7 G (SWITCHING) C1106 C1107 C1119 R1111
R1932A 330P 330P
150K
OPEN
R1932
120 D1960 22.5 (SWITCHING) D1703 C1704 R1703 0 S C1117 2.2
10P/6.3KV 2.2K
OPEN 6.3 15BSB-T26 1000P 10K
D1961 5.6 D1972 R1979
OPEN OPEN 6.8K
D1931 R1980
5V6BSB-T26 R1936 R1936A D1970 180 23.8
180 OPEN 5V6BSB-T26 D Q1702 CN1101
R1705 D1704 TK50P04M1 1
R1935A R1935 R1970A 100 24.8 G (SWITCHING) BACK
OPEN 1.5K IC1930 OPEN C1108 D1504 2 LIGHT
R1112 R1113
D1932 TLP781F D1705 C1706 R1706 20.5 S 10P/6.3KV 39K 0 DAN202U
(FEEDBACK) R1970 15BSB-T26 1000P 10K
Q1932 12.1 23.6 220 C1109 C1120 R1114
2SC2120-O C1934
4 1
D1971 Q1300 330P 330P 2.2K
3 6.0 (SWITCHING)
0
0.4
OPEN
0.4 3 2 22.5
R1981
0
33BSB-T26 2SA1576UBTLQ
(SW+10.5V)
17.0 10.6
C1303 C1302
R1223
10
20.5 D Q1703
R1709
4.7/1W
C1708
T1101
INVERTER
TRANS R1145 OPEN
R1115 470
R1116 R1117
100 13 D1507
DAN202U
Q1971 Q1972 R1309 11.0 0.1 10/50V R1707 D1706 TK50P04M1 0.022 2 8
KTC3875S-Y-RTK/P KTC3875S-Y-RTK/P 10K 100 0.7 G (SWITCHING)
163.6 Q1930 IC1931
TK7A50D
D (SWITCHING) TLP781F R1982 1.1 (SWITCHING) R1986 R1988 (SWITCHING) 3.3 S
4 7
R1119 R1120
(ISOLATOR) 1.5K 0 1K 1K 0 D1707 C1707 R1708 0 R1148 OPEN 100 13
C1930 G 15BSB-T26 1000P 10K 1 6
680P 0.2 1.1 0 R1987 0 D1300 R1118 470
C1982 C1983
/2KV S 0.2
4 1
C1981 0.47/50V OPEN OPEN 5V6BSB-T26 3 5
5.9 0.01 D1301 R1121 R1122
0 3 2 0 5V6BSB-T26 39K 0
C1931 D1930 C1110 C1111 C1121 R1123
1800P 27BSB-T26 10P/6.3KV 330P 330P 2.2K
R1501 100K
R1930 R1930A D1500 R1502 100K
47 OPEN DAN202U
6.0 R1503 100K
0.2
R1504 100K CN1102
0 R1931 R1931A 1
Q1931 47K OPEN BACK
KTC3198-Y-AT/P C1905 R1505 100K C1112 2 LIGHT
(SWITCHING) 1000P/250V 10P/6.3KV R1124 R1125 D1505
39K 0 DAN202U
D1501 R1506 100K
D1933 C1906 DAN202U
OPEN R1507 100K C1113 C1122 R1126
D1934 R1937 C1933 R1939A R1939 R1220 330P 330P 2.2K
1ZB36BB 0.39/2W 0.1 OPEN 2.2K OPEN J1002 R1508 100K T1102
INVERTER R1128 R1129
TRANS R1147 OPEN 100 13
J1091 R1509 100K D1508
D1200 D1202 DAN202U
HOT IC1200 OPEN
D1502 R1510 100K 2 8
R1127 470
2 TO POWER SUPPLY
D1201
0 1
BD9244AFV
(PWM CONTROL)
24 1.0
R1216
100
R1221
1
JS1200
R1229
0
C1500 R1500
DAN202U
R1511 100K
R1512 100K
4
1
7
6
R1150 OPEN R1131 R1132
100 13
LCD
MODULE
CBA CN201
GND
CN1001
15 COLD 1.0 2 REG 23 7.6 Q1203
0.01 1M
3 5
R1130 470
R1133 R1134
ASSEMBLY
C1204 C1205 OPEN 39K 0
INV+13V(NU) 14 27.0 3
OUTPUT 22 27.0 0.1 2.2
7.6
(SWITCHING) R1227
GND 13 5.1 OPEN C1114 C1115 C1123 R1135
BACKLIGHT-ADJ 12 C1208 25.1 4 21 25.1 C1209 10P/6.3KV 330P 330P 2.2K
0.47 0.47 0 R1228
BACKLIGHT-SW 11 20.5 5 OPEN
20 20.6 5.1
PROTECT3 10 R1225
GND 9 10.6 6 VCC VLO 19 2.2 OPEN 0.2
LOGIC
LCD+13V 8 C1206 C1201 J1001 0 Q1204
10/50V 0.1 4.0 7 STB 18 1.2 OPEN OPEN
LCD+13V 7 R1205 R1204 PWM (SWITCHING)
560K 75K 1.5 8
VGH 6 17 0.8
C1213 FEED R1226 R1513
GND 5 C1501
Q1303
2SA1576UBTLQ
0.01 9 OSC BACK 16 1.3 OPEN 1000P 1M
P-ON+3.3V 4 R1202 C1203
(SWITCHING) 0 10 GND 6800P
LCD-5V 3 130K 15 0.6
10.6 8.0 R1213 R1214
VCOM 2 4.7K 0 0 11 C1202 R1515 R1516
R1304 R1203
8.2K 14 0 6800P 27K 0
GND 1 R1307 8.6 4.7K DUTY PROTECT
1K 3.1 12 13 0 C1502
OPEN
R1514
39K
TO LCD MODULE R1303 C1301 C1210
ASSEMBLY CN1003 R1308 4.7K 1000P R1209 C1207
1000P
0.47
GND 1 0 4.7K
0
4.7K
LCD+13V 2 12.9 R1306
10K 0.7
Q1301
KTC3875S
LCD+13V 3 12.9 -Y-RTK/P R1201
1 VGH
GND
P-ON+3.3V
4 29.0
5 0
6 3.4
C1936
OPEN
C1935
OPEN
C1311
1000P
R1310
22K 0 (SWITCHING) 68K
R1215
10K
R1212
10K 0.1
3.1
Q1201
KTC3875S-Y-RTK/P
P-ON+3.3V 7 3.4 C1211
OPEN
R1208
22K 0 (SWITCHING)
LCD-5V 8 -5.1 C1937
OPEN 3.3 R1206
GND 9 0 C1938
OPEN 0 10K D1203
VCOM 10 5.3 0 Q1202 R1207 C1200 C1212 R1200 C1214
GND 11 0 C1939
OPEN
KTC3875S-Y-RTK/P 33K OPEN 0.47 68K OPEN
(SWITCHING)
A B C D E F G
10-7 PL11.0SCINV
Function Schematic Diagram
FUNCTION CBA
2 TO IR SENSOR
CBA CL103A CL103B
AL+3.3V 1
GND 2
KEY-IN1 3
A B C
10-8 PL11.0SCF
IR Sensor Schematic Diagram
IR SENSOR CBA
2 RS101
KSM-712TH2E
(REMOTE SENSOR)
VOUT
Vcc
GND
1 2 3
C104
0.1
R102 R101
TO POWER SUPPLY 3.3K 100
CBA CN101 CL102B
GND 1 R106
1K
REMOTE 2
AL+3.3V 3 C103 D109 C101 C102 D108
330P OPEN 47/16V OPEN OPEN
KEY-IN1 4 R103
9.1K
P-ON+9V 5
D101
SLR343WBCT3XM
POWER
TO FUNCTION
1 CL103A
1
2
3
CBA CL103B
AL+3.3V
GND
KEY-IN1
4 KEY-IN2
A B C
10-9 PL11.0SCIR
Digital Main 1 Schematic Diagram [TYPE A]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
CONTINUE
DIGITAL 5
DIGITAL MAIN CBA UNIT P-ON+3.3V
BACKLIGHT-ADJ
IC4202
AT24C16BN-SH-T BACKLIGHT-ADJ(1)
(NO CONNECTION) CN3903 (MEMORY) 8 7 6 5 LCD+12V(1)
+3.3V 1 1 A0 VCC 8
BUS-OPEN 2 IC3752 CN3904 (NO CONNECTION)
C3901 2 A1 WP 7 OPEN 31 LCD+12V
GND 3 OPEN
1 2 3 4 R3838 C3766 30 LCD+12V
4 SDA
SCL
(NO CONNECTION)
4
5
CN4104
3 A2
4 GND
SCL 6
SDA 5
R3905
R3903
OPEN
OPEN
R3800
OPEN
OPEN
C3786
OPEN
OPEN
29
28
27
LCD+12V
LCD+12V
LCD+12V
GND 20 26 GND
R3907 OPEN R3798
LVDS3(+) 19 OPEN Q3751 25 GND
R3906 OPEN OPEN
LVDS3(-) 18 R3799 24 GND
GND 17 R3921 OPEN 23 LLV0(+)
LVDSCE(+) 16 OPEN 22 LLV0(-)
LVDSCE(-) 15 C3904 R3937 21 LLV1(+)
R3933 R3932 1 OPEN R3904 R3912
GND 14 100 100 OPEN OPEN 20 LLV1(-)
LVDS2(+) 13 19 LLV2(+)
LVDS2(-) 12 18 LLV2(-)
GND 11 R3909 R3913 17 GND
22 22
LVDS1(+) 10 16 LLVCNK(+)
R3957 R3916 R3902
LVDS1(-) 9 10K 22K 0 15 LLVCLK(-)
R3934 R3951
GND 8 10K OPEN 14 GND
LVDS0(+) 7 IC3901 13 LLV3(+)
BU9069KUT C3912
LVDS0(-) 6 1 12 LLV3(-)
TIMING
GND 5 COTROLLER 11 LLV4(+)
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
GND 4 10 LLV4(-)
VDDIO
TEST
PWMO
PWMI
VDDP
OE2
GND
GND
GND
NU
NU
NU
C3911
GND 3 1 9 LLV5(+)
+3.3V 2 R3935 8 LLV5(-)
+3.3V 1 2.2K 7 GND
1 48
R3936 CONTROL SIGNAL GENERATOR 6 TP
2.2K
2 47 5 POL
*1 R3919
IC3301(1/5) OPEN 4 CPV
3 NU SERIAL 46
ZR39775HGCF C3921 INTERFACE 3 OE1
DIGITAL SIGNAL PROCESS 1
/MAIN MICRO CONTROLLER 4 NU 45 2 XA0
R4110 0 1 STV
AE24 5 VDD-REG 44
R4109 0
AF24 TO LCD MODULE
6 GND 43 CN3902 ASSEMBLY
AE19
24 GND
AF19 7 42 L3907 EXC24CG900U
R4112 0 R3931 23 LLV0(+)
AD24 100 DATA PROCESSING LVDS
R4111 0 8 OUTPUT 41 22 LLV0(-)
AD23 L3906 EXC24CG900U
R4114 0 21 LLV1(+)
AF23 9 GND 40
R4113 0 R3930 GAMMA CORRECTOR 20 LLV1(-)
AE23 100 FRC L3905 EXC24CG900U
R4116 0 10 LINE BUFFER VDDM 39 19 LLV2(+)
AE22
R4115 0 DATA 18 LLV2(-)
AF22 11 LVDS 38
R4118 0 R3929 RX INPUT 17 GND
AD22 100 LATCH L3904 EXC24CG900U
R4117 0 12 37 16 LLVCNK(+)
AD21
2 LVDS
TX AF21
AE21
AE20
R3928
100
13
14
36
35
L3903 EXC24CG900U
15
14
13
LLVCLK(-)
GND
LLV3(+)
12 LLV3(-)
AF20 15 34 L3901 EXC24CG900U
R3927 11 LLV4(+)
AF18 100
16 33 10 LLV4(-)
AE18 LVDS RX L3902 EXC24CG900U
9 LLV5(+)
AD17
VDDL
VDDL
8 LLV5(-)
GND
AD18
7 GND
AE17 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 R3945 0
6 TP
AF17 R3946 0
5 POL
AF16 R3958 R3947 0
10K 4 CPV
AE16
3 OE1
AD15 L3908 0 R3920 1K
2 XA0
AD16 C3924 C3927 C3910 C3902 R3917 0 R3949 0
1 0.1 1 10 1 STV
AE15 R3915 22 R3948 0
AF15 R3914 22
R3910 OPEN
OPEN
220P
220P
220P
220P
100K
OPEN
100K
OPEN
OPEN
OPEN
R3908 OPEN
TO DIGITAL
MAIN 2 R3918 OPEN
IC3301(2/5)
R3956
R3954
R3953
R3950
R3952
R3955
C3920
C3919
C3918
C3916
C3917
R3911 OPEN
1 NU
NU
AD19
AD20
R3901
1.1K
R3923
R3922
R3924
OPEN
OPEN
OPEN
OE2
POL
CONTINUE
DIGITAL 2
A B C D E F
10-10 PL11.0SCDA1
Digital Main 2 Schematic Diagram [TYPE A]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
CONTINUE
R3002 DIGITAL 3
0 *1
CONTINUE SDA
DIGITAL 5 C3002 IC3301(2/5)
R3003 L3002 C3004 15P ZR39775HGCF SCL
P-ON+3.3V R3004 OPEN 0.22uH 33P
0 DIGITAL SIGNAL PROCESS CONTINUE
AL+3.3V /MAIN MICRO CONTROLLER DIGITAL 4
C3003 C3013 0.1 C3020 0.1 R3022 22 R3724 100
(NO CONNECTION) CN3101 15P AF4 NU U3 SDA
C3014 0.1 C3021 0.1 R3021 22 R3723 100
4 GPIO-P2 1
GND 2
R3140 L3004
R3001 3.9K
AE4 NU
AF2
AE2
AD3 NU
DEMODULATOR
/MPEG
DECODER
NU
NU
NU
V3
U4
V4
U5
C3026
OPEN
C3025
OPEN
R3720 100
C3740
1000P
SCL
RESET
CONTINUE
DIGITAL 5
OPEN OPEN C3005 0.1 R3722 100
AD2 NU NU V5 AUDIO-MUTE
C3007 0.1 R3703 100
AD1 NU KEY-IN1
C3059 C3060 C3008 0.1 TO DIGITAL C3022 0.1 R3023 22
OPEN OPEN AF1 NU AA3
C3009 0.1 MAIN 3 C3024 TO POWER SUPPLY
AE1 NU IC3301(3/5) NU AB3 OPEN CN3702 CBA CN302
IC3001 AD8 NU NU AB4 29 KEY-IN1
OPEN AC7 NU NU AA4 C3734
100P 28 DIF-OUT2
1 VCC 5 AC8 GPIO0 C3714 27 GND
C3034 0.22 R3031 10 OPEN
2 AC6 NU U2 26 DIF-OUT1
R3006 R3005 4.7K C3035 0.22 R3032 10
OPEN AE7 NU U1 25 GND
3 GND 4 R3044 OPEN C3046 C3045
R3007 AF8 NU SW 33P 33P R3033 10 24 IF-AGC
2.2K C3036 0.22
AF7 IF-AGC V1 23 RESET
C3037 4700P R3026 0
C3006 AA5 NU V2 22 SCL
100P C3038 C3047
R3108 OPEN 33P 21 SDA
R3101 4.7K NU W2 C3738 20 AUDIO-MUTE
R3104 100 33P
R3102 4.7K C10 GPIO-P0 NU W1 19 COM-VIDEO-Pr-IN
100 C3739 C3736 C3732
C11 RESET-LCD 33P 1000P 33P 18 GND
R3111 4.7K
3 Q3704
OPEN
(BUFFER)
R3106 4.7K
R3751
R3750 OPEN
C12 GPIO-P2
D10 GPIO-P1
D11 GPIO-P4
D12 NU
NU
NU
Y1
Y2
2 CONTINUE
DIGITAL 5
OE2
W23 POL
V23 NU
V22 NU
V24 NU TO DIGITAL TO DIGITAL
GND *A
D3706
R3721 100
1 OE2
POL
TP
CPV
F2 USB-EN *A:B24,F6,J10~J18,K9~K18,L9~L18, NU
F3 NU
F4 NU
F5 NU
M9~M18,N9~N18,P9~P18,R9~R18, NU
R25,T9~T18,U9~U18,V9~V18,V25,
AE25 NU
H3
AA6
K22
R3836
0
OPEN OPEN OPEN
OE
STV
VCOM-PWM
DIGITAL MAIN CBA
UNIT
G H I J K L
10-11 PL11.0SCDA2
Digital Main 3 Schematic Diagram [TYPE A]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
4 DIGITAL 2
AUDIO(L)
AUDIO(R)
SPDIF R3803 R3820 R3821 C3802 R3804 R3822 R3823 C3805 R3806 R3807
AUDIO(R)-OUT
AMP(L)-OUT
AMP(R)-OUT
47K 0 0 10 47K 0 0 10 47K 47K
P-ON+5V C3803 C3801 C3806 C3804
0.1 10 0.1 10
16 15 14 13 12 11 10 9 16 15 14 13 12 11 10 9 CONTINUE
DIGITAL 4
*1 GND VCC NU NU GND VCC NU NU EJTCK
IC3301(3/5) LPF DAC LPF DAC R3149 100
ZR39775HGCF JTMS
LPF DAC LPF DAC R3153 100
DIGITAL SIGNAL PROCESS JTDO-M
/MAIN MICRO CONTROLLER 4X/8X 4X/8X R3154 100
IC3801 OVERSAMPLING ENHANCED IC3802 OVERSAMPLING ENHANCED JTDI-M
C3055 10 PCM1782DBQR ZERO DIGITAL FILTER MULTI-LEVEL PCM1782DBQR ZERO DIGITAL FILTER MULTI-LEVEL R3151 OPEN
M1 DETECT DELTA-SIGMA DETECT DELTA-SIGMA JTDO-T
C3056 10 AUDIO D/A /FUNCTION AUDIO D/A /FUNCTION R3152 OPEN
M2 CONVERTER CONTROLLER MODULATOR CONVERTER CONTROLLER MODULATOR JTDI-T
R4101 0
L1 TRSTN
SERIAL SYSTEM AUDIO SERIAL SYSTEM AUDIO RESET
L2 CONTROL PORT CLOCK SERIAL PORT CONTROL PORT CLOCK SERIAL PORT
NU K1 MANAGER MANAGER R3164
4.7K
NU K2 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
NU J1 R4102
47 CN4101 (NO CONNECTION)
NU J2 1 VDD
NU H1 2 TRSTN
3 NU
NU
NU
H2
K3
J3
R3041 10K R3801 R3802 R3808 R3809
C3818
OPEN
C3819
OPEN R3805
3
4
5
ADATA1
EJTDO
EJTMS
TO DIGITAL NU AC9 100 100 100 100 100
MAIN 2 R3042 10K 6 EJTCK
IC3301(2/5) NU AD13 7 RESET
R3043 10K
NU AF14 8 RESET
4.7K
OPEN
AUDIO
1K
1K
1K
I/F 9 VSS
R4103
R4106
R4104
R4105
R4107
TO DIGITAL C3816 100P
MAIN 4 C3815 100P R3810 OPEN
IC3301(4/5)
C3814 100P R3811 OPEN
R3828 33 R3813
ACLK AD10 OPEN
R3829 33 R3835 R3834
BCLK AD9 0 0
R3830 33 R3814
LRCLK AD12 OPEN
R3831 33
AC10 R3812
R3832 33 OPEN R3819
AD14 10K
NU AE14
C3812 C3813
100P 100P R3824 OPEN
AF12 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
R3825 OPEN
MUTEXSPO
SYSCLKO
RESETOX
DATAO1
DATAO2
SPDIFO
LRCKO
BCKI
MCLK
VSS3
BCKO
SCLO
SDAO
ADDR
NU
NU
NU
NU
NU
NU
AF11
2 AF10
AF9
AD11
R3826
R3827
OPEN
OPEN
C3023
C3054 10 1000P
NU AE8 IC3803
C3015 0.1 BU9414FV-E2
C3053 10 AUDIO D/A
NU AE12 CONVERTER
C3016 0.1
MUTEX-DAC
C3052 10
MUTEX-SP
DVDDCORE
NU AE13
LDOPOFF
ANATEST
SDATA1
SDATA2
RESETX
PLLFIL
C3017 0.1 CONTINUE
LRCKI
REG15
SCLI
SDAI
VSS1
VSS2
MODE
DIGITAL 2
VDD
NU
NU
NU
GND AF13 RESET-DSP
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
R3818 R3815
CONTINUE R3817 0 1.5K
DIGITAL 5 100 C3810
R3833 OPEN C3811 2700P
P-ON-H1 C3808 C3809 0.027
C3817 R3816 2.2 OPEN
OPEN R3940 100
100
BC3803
1 C3807
10
BC1608HS601-T
SDA
SCL
CONTINUE
DIGITAL 2
M N O P Q R
10-12 PL11.0SCDA3
Digital Main 4 Schematic Diagram [TYPE A]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
*1
IC3301(4/5)
ZR39775HGCF
DIGITAL SIGNAL PROCESS
DIGITAL MAIN CBA UNIT
L3402 /MAIN MICRO CONTROLLER HDMI-
OPEN R3409 JK3701 CONNECTOR-1
0 S0-DQ15 B15 SO-DQ15 B8 1 TMDS-D2(+)
C3419 S0-DQ14 A21 S0-DQ14 A8 2 D-SHIELD0
0.1
IC3201 S0-DQ13 A14 S0-DQ13 C8 3 TMDS-D2(-)
K4T51163QG-HCF7 R3402 C3401 S0-DQ12
(DDR2 SDRAM) 100 0.1 B22 S0-DQ12 C9 4 TMDS-D1(+)
C3403 0.1 S0-DQ11 B20 S0-DQ11 A9 5 D-SHIELD1
*A VDD C3420 R3403 C3421 C3402 R3410
C3404 0.1 0.1 100 L3401 10 0.1 OPEN S0-DQ10 B17 S0-DQ10 B9 6 TMDS-D1(-)
VREF J2 0
C3405 0.1 R3401 S0-DQ9
4 C3406
C3407
C3408
0.1
0.1
0.1 E2 NU
CKE
CK
CK
K2
J8
K8
100
S0-DQ8
S0-DQ7
S0-DQ6
B21
A15
B14
A22
S0-DQ9
S0-DQ8
S0-DQ7
S0-DQ6
HDMI0-CEC
B10
A10
D8
B11 Q3703
2SK3018
R3781
82K
7
8
9
10
TMDS-D0(+)
D-SHIELD2
TMDS-D0(-)
TMDS-CLOCK(+)
C3409 0.1 A2 NU S0-DQ5
NU L8 B13 S0-DQ5 A11 (BUFFER) D3704 11 C-SHIELD0
C3410 0.1 R8 NU S0-DQ4 R3734 RB751S-40TE61
RAS K7 A23 S0-DQ4 HDMI-HPD D9 27K 12 TMDS-CLOCK(-)
C3411 0.1 R7 NU S0-DQ3
R3 NU CAS L7 B19 S0-DQ3 HDMI0-5VSENSE D7 13 CEC
C3412 0.1 S0-DQ2 A18 S0-DQ2 NU D3 R3731 14 NU
WE K3 390
C3413 0.1 S0-DQ1 B23 S0-DQ1 HDMI0-REXT C3 15 SCL
1-U3 BA2/NU L1
C3414 0.1 B7 UDQS S0-DQ0 A13 S0-DQ0 16 SDA
2-U3 BA1 L3
C3415 0.1 A8 UDQS/NU R3727 R3728 17 GND
3-U4 BA0 L2 47K 47K
C3416 0.1 B3 UDM 3-S4 A20 S0-UDM 18 VCC
S0-DQ15 A12 R2
C3417 0.1 B9 DQ15 6-S3 A19 S0-LDM 19 HOT-PLUG-DETECT
S0-DQ14 A11 P7
C3418 0.1 B1 DQ14 R3773 C3745 R3778
S0-DQ13 A10/AP M2 10K 0.1 1K R3726 C3744 D3702
D9 DQ13 A24 S0-VREF 10K 0.1 EDZTE61 HDMI-
S0-DQ12 A9 P3 JK3702 CONNECTOR-2
D1 DQ12 A8 P8 2-S4 B4 1 TMDS-D2(+)
S0-DQ11 D3 DQ11 A16 S0-UDQSN
S0-DQ10 A7 P2 1-S4 B16 S0-UDQS A4 2 D-SHIELD0
D7 DQ10 A6 N7 5-S3 C4 3 TMDS-D2(-)
S0-DQ9 C2 DQ9 B18 S0-LDQSN
S0-DQ8 A5 N3 4-S3 A17 S0-LDQS C5 4 TMDS-D1(+)
C8 DQ8 A4 N8 A5 5 D-SHIELD1
4-U3 D16 S0-RASN HDMI
F7 LDQS A3 N2 I/F B5 6 TMDS-D1(-)
5-U3 E8 LDQS/NU C16 S0-CASN
6-U4 A2 M7 D20 S0-WEN B6 7 TMDS-D0(+)
F3 LDM A1 M3 A6 8 D-SHIELD2
S0-DQ7 F9 DQ7 B12 S0-CKN
A0 M8 B7 9 TMDS-D0(-)
3 S0-DQ6
S0-DQ5
S0-DQ4
S0-DQ3
F1
H9
H1
DQ6
DQ5
DQ4
ODT
VSS *B
K9
A12
C21
C13
C14
S0-CK
S0-CKE
S0-ODT
NU
A7
HDMI1-HPD D6
HDMI1-5VSENSE C7
R3779 1K
10
11
12
TMDS-CLOCK(+)
C-SHIELD0
TMDS-CLOCK(-)
H3 DQ3 R3772 C3743 13 CEC
S0-DQ2 H7 DQ2 *A:A1,A9,C1,C3,C7,C9,E1,E9, C24 S0-A12 10K 0.1
S0-DQ1 G1,G3,G7,G9,J1,J9,M9,R1 C18 S0-A11 14 NU
G2 DQ1 15 SCL
S0-DQ0 *B:A3,A7,B2,B8,D2,D8,E3,E7, D22 S0-A10
G8 DQ0 F2,F8,H2,H8,J3,J7,N1,P9 16 SDA
D18 S0-A9
R3729 R3730 17 GND
CONTINUE D14 S0-A8 47K 47K
DIGITAL 5 D23 S0-A7 18 VCC
P-ON+1.8V R3742 19 HOT-PLUG-DETECT
D17 S0-A6 OPEN
P-ON+3.3V R3725 C3742 D3701
C19 S0-A5 10K 0.1 EDZTE61 HDMI-
AL+3.3V JK3704 CONNECTOR-3
C15 S0-A4
DDR+1.8V C3107 D1 1 TMDS-D2(+)
0.1 C23 S0-A3
D2 2 D-SHIELD0
C17 S0-A2
CONTINUE C1 3 TMDS-D2(-)
DIGITAL 2 D19 S0-A1
C2 4 TMDS-D1(+)
SDA D15 SO-A0
B1 5 D-SHIELD1
SCL C22 S0-BA2
B2 6 TMDS-D1(-)
RESET C20 S0-BA1
C3101 C3115 A1 7 TMDS-D0(+)
0.01 OPEN C3116 D21 S0-BA0
R3171 0.033 A2 8 D-SHIELD2
OPEN
CONTINUE 4 3 R3404 59 B3 9 TMDS-D0(-)
DIGITAL 5 Q3101 IC3103 B26 NU
PROTECT2 OPEN OUT CD R3405 59 A3 10 TMDS-CLOCK(+)
D3102 OPEN PST8420UR A26 NU R3780 1K
PROTECT3 (RESET) GND VDD R3406 150 HDMI2-HPD D4 11 C-SHIELD0
A25 NU
2 PROTECT1
PROTECT5-USB
D3103 OPEN 1 2 C3109
12P
C3108
12P
X3101 R3128 R3127
25MHz 330 1M N1 CLKIN
N2 CLKOUT
HDMI1-5VSENSE E6
S1-DQ11 L25
R3407
4.7K
R3408
4.7K
R3739
10K
C3747
0.1
12
13
14
TMDS-CLOCK(-)
CEC
NU
R3159 S1-UDM L26 15 SCL
10K NU U25 16 SDA
(NO CONNECTION) CN4103
USB+5V 1 NU U26 R3113 R3740 R3741 17 GND
4.7K 47K 47K
UARTSUB-TX 2 CLKIN-SEL AF3 18 VCC
UARTSUB-RX 3 NU AD25 R3148 19 HOT-PLUG-DETECT
OPEN
GND 4 AC12 USB(+) NU AD26 R3771 C3746 D3707
AB12 USB(-) 10K 0.1 EDZTE61
R3138 100 NU AE26
IC3101 R3105 D3101 R3162 4.7K R3139 AB21 MOR-RESET-N
-OUT
AUDIO VIDEO
NU AF26
CONTINUE
W25X32VSSIGE 33K 1SS400 4.7K DECODER DECODER DIGITAL 5
(MEMORY) AB22 MOR-RESET-N REMOTE R22 P-ON+5V
AD7 GPIO1 NU N22 REMOTE
1 CS VCC 8 R3123 100 TO DIGITAL TO DIGITAL
W26 RESET NU P22
R3167 100 MAIN 3 MAIN 2
2 SO NU 7 AB26 SPI-HOLD IC3301(3/5) IC3301(2/5) R3120 100 C4101
R3126 4.7K R3125 4.7K RXD0 M22 0.1
AC26 SPI-SEL1 R3119 100 CN4102 (NO CONNECTION)
3 WP SCK 6 R3168 100 TXD0 L22
AC24 CS R3115 4.7K 1 P-ON+5V
R3166 100 NU D13 R3165
4 GND SI 5 AB25 SCK 4.7K 2 UART0-TX
CONTINUE R3169 100 NU E13
DIGITAL 2 AC25 SOUT R3114 3 UART0-RX
WP R3135 100 OPEN R3124 4 GND
R3761 10K AB24 SIN JTDO-M B25 4.7K
USB-EN R3133 4.7K
AC22 I2C-MORPH-ENA CONTINUE
R3129 10K JTDI-M E19 DIGITAL 3
GPIO1 AC21 TV-I2C-D R3117 100
R3132 10K EJTCK E17 EJTCK
R3121 R3122 AC20 TV-I2C-C JTMS E15 JTMS
1.8K 1.8K
AC19 SDA
1 (USB JACK)
USB+5V
CN3704
1
C3750
1
C4102
0.1
Q3701
2SB1732TL
(SW+5V)
R3760
10K C3724
1
R3770
1K C3752
OPEN
R3767
33K
R3130
R3131
4.7K
4.7K
AC18 SCL
AC17 I2C0-D *B:C25,C26,D24~D26,E23~E26,
AC16 I2C0-C F23~F26,G23~G26,H23~H26,
J23~J26,K23~K26,L23,L24,
JTDO-T
JTDI-T
TRSTN
E18
E14
E16
R3116 100
JTDO-M
JTDI-M
JTDO-T
JTDI-T
USB(-) 2 R3762 R3763 R3715 M23~M26,N23~N26,P23~P26,
330 330 R3764 2.4 *B NU R24,R26 TRSTN
USB(+) 3 10K IC3701 R3768 RESET
GND 4 C3753 R3775 C3754 R3774 R3765 AS431AKTR-E1 33K R3766
56P 15K 56P 15K Q3702 15K SHUNT 1.6
2SC4081UBTLQ REGULATOR R3769
(NO CONNECTION) CN3102 (SWITCHING) 180
I2C0-C 1
GND 2
I2C0-D 3
S T U V W X
10-13 PL11.0SCDA4
Digital Main 5 Schematic Diagram [TYPE A]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
R3777
R3861
R3759
*1
OPEN
OPEN
OPEN
PROTECT2 IC3301(5/5)
PROTECT3 ZR39775HGCF
DIGITAL SIGNAL PROCESS CONTINUE
PROTECT1 /MAIN MICRO CONTROLLER R3758 100 DIGITAL 2
R3504 OE2
PROTECT5-USB 0
4 C3571
1
C3502
0.1
E7 HDMI-VDD3P3
E8 HDMI-VDD3P3
F7 HDMI-VDD3P3
F8 HDMI-VDD3P3
NU
NU
NU
NU
K4
AE3
M6
N6
R3705 100
P-ON-H1
P-ON-H2
BACKLIGHT-SW
REMOTE
*C IO-VDD NU U6 R3704 OPEN
LED1
C3530 C3529 C3528 C3527 C3526 NU V6 R3701 100
10 10 10 10 10 VCOM-PWM
NU AB7 C3704
100P CONTINUE
C3535 C3534 C3533 C3532 C3531 NU AB10 DIGITAL 2
1 1 1 1 1 AUDIO-MUTE AB9 IC3651 AUDIO-MUTE
NU AB8 OPEN
C3540 C3539 C3538 C3537 C3536 R3323 845 KEY-IN1
0.1 0.1 0.1 0.1 0.1 NU G2 CONTINUE
CTL
VCC
GND
OUT
NU L6 DIGITAL 4
C
C3567 C3566 C3543 C3542 C3541 R3322 845 P-ON+1.8V
0.1 0.1 0.1 0.1 0.1 NU G1 R3651 1 2 3 4 5
NU K6 OPEN P-ON+3.3V
R3654 AL+3.3V
C3525 C3570 C3569 C3568 R3652 C3653 OPEN R3655
0.01 0.1 0.1 0.1 LVDSVCRX-VDD33 H6 OPEN OPEN OPEN DDR+1.8V
R3653
LVDSVCRX-VDD33 J6 OPEN CONTINUE
R3110 DIGITAL 2
0 LVDSVCTX-VDD33 G5 C3654 C3655 P-ON+3.3V
AC13 USB-VDD33 OPEN OPEN
C3106 C3104 LVDSVCTX-VDD33 G6 BC3602 AL+3.3V
R3112 1 0.1 C3518 4.7 OPEN
0 NU P4 CONTINUE
AF25 USB2-VDD33 DIGITAL 4
3 BC3001
BK1608HS601-T
C3043 C3032
C3105
1
C3033
C3114
0.1
C3031
V26 PLL-VDD33
NU
VDD33-BOD
KEY-IN1
Y3
AB5
AC5
D3501
1SS400
C3501
100/4V R3008 OPEN
C3652
OPEN
R3707
100
C3651
OPEN P-ON+5V
REMOTE
CONTINUE
1 0.1 L3502 1 0.1 R3009 10K DIGITAL 1
0 KEY-IN2 AD6 R3708 100 P-ON+3.3V
AC15 LDI-VDD33 R3716 100
C3584 C3585 C3503 PROTECT1 AD5 R3714 100 BACKLIGHT-ADJ
0.1 L3501 1 0.1 AB15 LDI-VDD33 R3757 OPEN
BK1608HS601-T PROTECT2 AD4 C3062 R3012 IC3603 C3715 C3718 C3721 BACKLIGHT-ADJ(1)
AB2 DM-PLL-VDD 0.1 100K BD7820FP-E2 1000P OPEN 1000P
PROTECT3 AE5 C3722 LCD+12V(1)
C3505 C3504 (+1.8V REG.) 1000P
4.7 0.1 PROTECT5-USB AE6 TO POWER SUPPLY
R3505 CN3701 CBA CN301
0 NU AB6
CTL
VCC
GND
OUT
E9 HDMI-VDD1V R3039 51K R3744 R3010 OPEN 29 VCOM-PWM
NU AC3
C
C3572 C3508 E10 HDMI-VDD1V C3001 0.1 4.7K R3011 OPEN 28 BACKLIGHT-ADJ
1 0.1 NU AC4 1 2 3 4 5 R3745
F9 HDMI-VDD1V R3611 OPEN 27 LED1
F10 HDMI-VDD1V R3013 OPEN 0 R3613 26 BACKLIGHT-SW
VDDADC8 AF5 10K R3614 R3743 C3713 C3712
R3103 R3040 9.1K C3642 10K 10K 1000P 1000P 25 REMOTE
0 RC-OSC-REXT AF6 OPEN R3612 R3706 100
AC11 USB-VDD1 C3051 C3061 BC3502 3.9K 24 OE2
C3102 C3103 AVDD3-SYNC1 R3 22P OPEN BK1608HS601-T
0.01 1000P C3639 23 GND
AVDD3-HPLL M4 0.1 C3751 C3710
*D CORE-VDD C3510 C3509 C3511 C3640 IC3602 100P 100P 22 AL+3.3V
AVDD18-HPLL L3 0.1 1 0.1 10 BD7820FP-E2
C3591 C3590 C3589 C3588 C3587 C3586 BC3503 21 AL+3.3V
1 1 10 10 10 10 AVSS-HPLL M3 BK1608HS601-T (+1.8V REG.) C3708 C3706
10 0.1 20 P-ON+3.3V
AVDD3-SYNC N3
C3512 C3513 C3519 19 P-ON+3.3V
CTL
VCC
GND
OUT
C3596 C3595 C3641 C3594 C3593 C3592
C
10 0.1 18 GND
AVDD18-R P2 1 2 3 4 5
R3610 17 GND
C3615 C3614 C3600 C3599 C3598 C3597 AVDD18-G P1 BC3505 10K C3748 C3749
1 1 1 1 1 1 BK1608HS601-T R3657 10 0.1 16 P-ON+7V
AVDD18-B R1 R3617 C3611 R3608 OPEN
C3514 C3515 C3520 OPEN 10 1K R3607 15 PROTECT2
AVDD18-SVIDEO R2 1000P 0.01 1 R3609 1K R3656
C3621 C3620 C3619 C3618 C3617 C3616 510 0 14 P-ON+5V
1 1 1 1 1 1 AVDD18-CVBS P3 BC3506
BK1608HS601-T BC3601 13 P-ON+5V
DVDD18 R4 C3612 C3544 BKP1608HS391-T C3701 C3707
C3627 C3626 C3625 C3624 C3623 C3622 C3506 C3507 L3001 C3521 0.1 100/4V 10 0.1 12 GND
1 1 1 1 1 1 0.01 1 BK1608HS601-T 0.1 11 PROTECT1
IF-VDD3P3 AC1 C3644 C3643 C3613 C3703
10 10 0.1 10 10 P-ON+3V
IF-VDD3P3 AC2 C3010 C3011 L3003 R3709 100
C3633 C3632 C3631 C3630 C3629 C3628 0.1 4.7 BK1608HS601-T 9 P-ON-H1
0.1 0.1 0.1 0.1 0.1 1 ACOD3-AVDD AE10
C3018 C3012 C3604 C3603 C3602 L3602 8 AMP(R)-OUT
ACOD3-AVSS AE11 0.1 1 0.1 10 10 BEAD C3705 C3719
C3638 C3637 C3636 C3635 C3634 0.1 1000P 7 GND
0.1 0.1 0.1 0.1 0.1 VFE-AVSS *F
6 AMP(L)-OUT
*E M-VDD R3616 5 PROTECT3
IOVDD-STBY0 H4 IC3601 22K
C3549 C3548 C3547 C3546 C3545 C3522 C3524 C3646 BD9329EFJ-E2 4 AUDIO(R)-OUT
10 10 10 10 10 IOVDD-STBY1 J4 1 10 1000P (DC-DC CONVERTER) C3601 3 GND
IOVDD-STBY2 H5 R3604 0.01
10 1 BST SS 8 2 AUDIO(L)-OUT
C3554 C3553 C3552 C3551 C3550 IOVDD-STBY3 J5 R3713 100
1 1 1 1 10 1 P-ON-H2
IOVDD-STBY4 K7 2 VIN EN 7 C3716
C3607 C3605 C3645 1000P
C3559 C3558 C3557 C3556 C3555 0.1 1 OPEN
3 SW COMP 6
L3601
FB 5
R3603
16K
C3606
1500P
CONTINUE
DIGITAL 3
P-ON+3.3V
N20,N21,P20,P21,R20,R21,T20~T26, 22uH P-ON+5V
CORE-VDD18-STBY4 T7 U20,U21,V7,V20,V21,W7,W20,W21, R3702 100
C3580 C3579 C3578 C3577 C3565 Y7~Y15,AA7~AA15 AUDIO(L)-OUT
0.1 0.1 0.1 0.1 0.1 CORE-VDD18-STBY5 R7 C3647 D3601 C3609 C3610 C3648 R3615 C3608 R3712 100
*E:E20~E22,F16~F22,G17~G22,H20~H22, 1000P OPEN 10 0.1 10 9.1K 100/4V AUDIO(R)-OUT
J20~J22,K20,K21 R3605 R3602 R3711 100
C3582 C3581 *F:L7,M7,N7,P7,U7,W4~W6,Y4~Y6 10 6.8K AMP(L)-OUT
0.1 0.1 R3710 100
R3601 AMP(R)-OUT
47K C3720 C3717 C3723 C3702
1000P 1000P 1000P 1000P
Y Z AA BB CC DD
10-14 PL11.0SCDA5
Digital Main 1 Schematic Diagram [TYPE B]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
VIDEO SIGNAL CONTINUE
DIGITAL 5
REMOTE
DIGITAL MAIN CBA UNIT R3903
AL+3.3V
P-ON+5V
OPEN
P-ON+3.3V
C3906 R3913 CN3901 (SMART PORT)
OPEN OPEN
R3904 1 SM-CLK
OPEN
Q3905 2 SM-MISO
OPEN
5 4 R3906 3 NU
R3912 OPEN
Q3906 4 SM-MISI
VCC
Y
OPEN OPEN R3911
IC3901 R3915 OPEN 5 GND
OPEN OPEN R3910 R3925
OPEN
GND
D3907 OPEN 6 REMOTE
OE
A
OPEN
1 2 3 C3905 R3909 R3907 R3914 CN3011 (NO CONNECTION)
OPEN OPEN OPEN Q3904 OPEN D3905 D3904 D3903 D3902 D3901
OPEN OPEN OPEN OPEN OPEN 31 LCD+12V
OPEN R3921
OPEN 30 LCD+12V
R3919 R3920 L3902 OPEN 29 LCD+12V
OPEN OPEN
R3902 OPEN L3901 OPEN 28 LCD+12V
L3903 OPEN 27 LCD+12V
*1 Q3903 L3904 OPEN 26 GND
IC3005(1/6) OPEN R3908 D3906 C3345
OPEN OPEN OPEN 25 GND
R8A05011BG-U0 R3918 OPEN
DIGITAL SIGNAL PROCESS Q3901 24 GND
/MAIN MICRO CONTROLLER OPEN R3901 R3905
OPEN OPEN R3917 C3901 23 LLV0(+)
OPEN OPEN
R3210 OPEN 22 LLV0(-)
SM-CLK K16 R3916 Q3907 21 LLV1(+)
R3514 OPEN OPEN OPEN
SM-MOSI K14 20 LLV1(-)
R3515 OPEN Q3908
SM-MOSO J16 OPEN 19 LLV2(+)
SM-PU-CONT F14 18 LLV2(-)
C3904 C3903 C3902 17 GND
OPEN OPEN OPEN 16 LLVCNK(+)
15 LLVCLK(-)
3 8 7 6 5
14 GND
13 LLV3(+)
12 LLV3(-)
11 NU
Q3002
R3561 OPEN OPEN 10 NU
R3560 OPEN 9 NU
R3007
R3559 OPEN 1 2 3 4 OPEN 8 NU
R3558 OPEN 7 GND
R3557 OPEN R3006 C3002 6 NU
OPEN OPEN 5 NU
R3556 OPEN
R3555 OPEN R3002 4 NU
OPEN Q3001 3 NU
R3554 OPEN OPEN
R3001 2 NU
R3553 OPEN OPEN
R3552 OPEN 1 NU
TO LCD MODULE
R16 CN3005 ASSEMBLY
C3352 OPEN
R15 24 GND
P14 23 LLV0(+)
C3349 OPEN
P13 22 LLV0(-)
N16 21 LLV1(+)
2 LVDS
TX N15
P16
P15
C3350 OPEN
C3351 OPEN
20
19
18
LLV1(-)
LLV2(+)
LLV2(-)
T16 17 GND
C3353 OPEN
T15 16 LLVCNK(+)
R14 15 LLVCLK(-)
C3354 OPEN
T14 14 GND
R13 13 LLV3(+)
C3355 OPEN
T13 12 LLV3(-)
11 LLV4(+)
10 LLV4(-)
9 LLV5(+)
TO DIGITAL 8 LLV5(-)
MAIN 2 7 GND
IC3005(2/6) R3537 0
TP L13 6 TP
POL M15 5 POL
CPV L16 4 CPV
OE L15 3 OE1
STV M14 2 XA0
NU M16 1 STV
100P
100K
100K
100K
100K
OPEN
100K
NU M13 CONTINUE
R3088 R3152 1K DIGITAL 5
7.5K
C3567
R3567
R3566
R3565
R3564
R3563
R3562
NU K15 P-ON+3.3V
CONTINUE
DIGITAL 2
LESET LCD N14 RESET-LCD
NU N13 CONTINUE
DIGITAL 5
OE2 L14 OE2
LCD+12V
A B C D E F
10-15 PL11.0SCDB1
Digital Main 2 Schematic Diagram [TYPE B]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
CONTINUE
R3144 100 DIGITAL 4
DIGITAL MAIN CBA UNIT R3142 100
AUDIO-MUTE
SDA
R3138 100
SCL
D3056
R3134 100
C3086
1000P
LIGHT-SENS
RESET
TO POWER SUPPLY
/MPEG 0.27uH 33P OPEN CN3006 CBA CN302
DECODER C3225
A12 10P 29 KEY-IN1
28 DIF-OUT2
C3074
R3360 1000P 27 GND
OPEN
26 DIF-OUT1
R3202 L3023 C3242 R3368 25 GND
2.2K OPEN OPEN OPEN
IF-AGC A16 24 IF-AGC
C3178 C3177 C3084 23 RESET
0.1 OPEN OPEN
22 SCL
21 SDA
20 AUDIO-MUTE
19 COM-VIDEO-Pr-IN
C3089 C3092 C3093 18 GND
33P 1000P 33P
17 COM-VIDEO-Pb-IN
C3095 16 GND
33P
15 COM-VIDEO-Y-IN
C3098 14 GND
33P
3 INPUT0 G1
INPUT1 D1
R3511 22
R3187 22
R3091 47
R3156 100
R3172 100
13
12
11
AUDIO(L)
INPUT0
AUDIO(R)
S-VIDEO-SW N12 10 INPUT1
C3099 C3101 C3100 C3102 9 GND
100P 100P 33P 33P
R3513 R3189 8 S-VIDEO-Y-IN
10K 10K
C3103 7 GND
33P
6 S-VIDEO-C-IN
R3175 100
5 S-VIDEO-SW
4 VIDEO-IN
C3104 C3105 C3107 3 GND
33P 33P 33P
2 SPDIF
IC3013
C3291 OPEN
C3292 OPEN
C3293 OPEN
OPEN 1 GND
(BUFFER GATE) C3112 R3181 C3111
100P OPEN 33P CONTINUE
1 VCC 5 R3154 100 DIGITAL 3
C3214 AUDIO(L)
R3296 OPEN 2 OPEN R3171 100
VGA-HSYNC A14 AUDIO(R)
R3298 OPEN 3 GND 4 SPDIF
VGA-VSYNC B14
C3194 OPEN IC3014 CONTINUE
A9 DIGITAL 6
C3195 OPEN OPEN
C7 (BUFFER GATE) R3326 R3321 P-ON+5V(1)
C3196 OPEN OPEN OPEN
2 C11 1
2
VCC 5 R3333
OPEN
R3334
VGA-SDA
VGA-SCL
33P
33P
33P
33P
33P
33P
OPEN
3 GND 4
D3041 D3054
C3256
C3255
C3254
C3287
C3288
C3289
1 TO DIGITAL TO DIGITAL
Q3010
2SC4081UBTLQ
(BUFFER)
R3183
100
R3377
OPEN
D3055
OPEN
14
15 10
9 4
5
MAIN 6 MAIN 1 R3416
IC3005(6/6) IC3005(1/6) OPEN R3532
OPEN
R3185 R3184
10K 10K
CONTINUE
DIGITAL 1
R3186 RESET-LCD
39K
G H I J K L
10-16 PL11.0SCDB2
Digital Main 3 Schematic Diagram [TYPE B]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
4 AUDIO(R)
SPDIF
R3500 R3499
C3338
100P
C3341
100P
C3227
100P
C3229
100P
R3503
OPEN
R3504
OPEN
R3501
OPEN
R3502
OPEN
AMP(R)-OUT
AL+3.3V
100P 100P
R3518 R3520 R3322 R3325
100 100 100 100
*1
IC3005(3/6)
R8A05011BG-U0
R3213 22
REMOTE C14
RESET-N J15
IC3009 R3191 R3182
R3178 BU4221F 100 56K
3.3K (RESET) CONTINUE
R3517 100 DIGITAL 4
VCOM-PWM F2 1 GND OUT 4 CPU-RESET-N
C3116 C3120
TO DIGITAL 2 VDD CD 3 OPEN 1000P
2 MAIN 2
IC3005(2/6)
AUDIO
I/F
KEY-IN1
LIGHT-SENS
PROTECT1
A15
A13
C13
R3313
R3315
R3316
R3312
22
22
22
22
C3106
0.1
C3252
0.1 C3113
0.47
PROTECT2 D13
R3314 100
TO DIGITAL PROTECT3 B13 CONTINUE
MAIN 6 R3233 22 DIGITAL 2
IC3005(6/6) DTV-ON-H2 G13
KEY-IN1
LIGHT-SENS
R3498 C3228
100K OPEN RESET
B6
A6
B7
CONTINUE
A7 DIGITAL 5
C3216 10
NU C5 P-ON+3.3V(2)
C3217 10
A8
CONTINUE
R3341 0 C3231 0.22 DIGITAL 5
LPF C12
PROTECT1
PROTECT2
1 B8
R3340 10K
C3218 10 PROTECT3
DTV-ON-H2
DTV-ON-H1
NU D11
C3219 10 P-ON-H2
NU D7
C3220 10 REMOTE
NU C6
VCOM-PWM
M N O P Q R
10-17 PL11.0SCDB3
Digital Main 4 Schematic Diagram [TYPE B]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
*1
IC3005(4/6)
R8A05011BG-U0
DIGITAL SIGNAL PROCESS
R3064 C3050 /MAIN MICRO CONTROLLER
100 0.1
M5 SD-VREF0
R3065 C3051 N3 GND
100 0.1
4 IC3002
SD-DQ15
SD-DQ14
R8
N8
SD-DQ15
SD-DQ14
M32TRST-N G2
R3224
10K
CN3007
1
(NO CONNECTION)
AL+3.3V
K4T51163QI-HCF7 SD-DQ13 P7 SD-DQ13 2 GND
(DDR2 SDRAM) C3009 SD-DQ12
C3029 0.1 0.1 R6 SD-DQ12 ASEBRKAK-N F15 3 ASEBRKAK-N
*A VDD SD-DQ11 ASEMD0 F16 4 ASEMD0
C3030 0.1 P6 SD-DQ11
C3031 0.1 SD-DQ10 N7 SD-DQ10 TRST-N E16 5 TRST-N
VREF J2
C3032 0.1 C3010 SD-DQ9 T5 SD-DQ9 TCK E15 6 TCK
0.1 SD-DQ8
C3033 0.1 P8 SD-DQ8 TDI D16 7 TDI
E2 NU CKE K2 SD-DQ7 TDO D15 8 TDO
C3034 0.1 P4 SD-DQ7
A2 NU CK J8 SD-DQ6 TMS E14 9 TMS
C3035 0.1 T3 SD-DQ6
R8 NU CK K8 SD-DQ5 R3522 10 CPU-RESET-N
C3036 0.1 R4 SD-DQ5 10K
R7 NU CS L8 SD-DQ4
C3037 0.1 T2 SD-DQ4
R3 NU RAS K7 SD-DQ3
C3038 0.1 P3 SD-DQ3
CAS L7 SD-DQ2
C3039 0.1 T4 SD-DQ2
1-V3 WE K3 SD-DQ1
C3040 0.1 B7 UDQS R3 SD-DQ1
2-V3 BA2/NC L1 SD-DQ0 R3516 100
C3041 0.1 A8 UDQS/NU N4 SD-DQ0 BACKLIGHT-ADJ F3
3-V3 BA1 L3 3-S3
B3 UDM T6 SD-UDM
SD-DQ15 BA0 L2 6-S3
B9 DQ15 R5 SD-LDM LED1 G14
SD-DQ10 A12 R2 2-S3 C3184
3 SD-DQ12
SD-DQ11
SD-DQ13
B1
D9
D1
D3
DQ14
DQ13
DQ12
DQ11
A11
A10/AP
A9
P7
M2
P3
R3049
100
1-S3
5-S3
4-S3
T7
R7
N5
P5
SD-UDQSN
SD-UDQS
SD-LDQSN
SD-LDQS
GND
XIN25
XOUT25
J14
H15
H16
R3223
18P
X3001
25MHz
C3183
SD-DQ14 A8 P8 1K 18P
D7 DQ10 A7 P2 R3029 15
SD-DQ9 C2 DQ9 J3 SD-RAS
SD-DQ8 A6 N7 R3030 15
C8 DQ8 H3 SD-CAS
4-V3 A5 N3 R3031 15 R3510 22
F7 LDQS L4 SD-WE AUDIO-MUTE E1
5-V3 A4 N8
E8 LDQS/NU GPY10 E13 CN3010 (NO CONNECTION)
6-V3 A3 N2 R3024 6.8 R3234 R3395 4.7K
F3 LDM R1 SD-CLKN OPEN R3468 1 P-ON+5V
SD-DQ7 A2 M7 R3015 6.8 100
F9 DQ7 R2 SD-CLK TXD0 G15 2 UART0-TX
SD-DQ6 A1 M3 R3016 15 R3469 100
F1 DQ6 L3 SD-CKE RXD0 G16 3 UART0-RX
SD-DQ5 A0 M8 R3048 15 R3396 4.7K
H9 DQ5 K2 SD-ODT 4 GND
SD-DQ4 ODT K9 R3035 15
H1 DQ4 M2 SD-A12 R3089 47
SD-DQ3 R3036 15 CS P12 C3253
H3 DQ3 VSS *B J2 SD-A11 OPEN CONTINUE
SD-DQ2 R3037 15 DIGITAL 5
H7 DQ2 *A:A1,A9,C1,C3,C7,C9,E1,E9, J4 SD-A10 R3092 47
SD-DQ1 G1,G3,G7,G9,J1,J9,M9,R1 R3038 15 SOUT R11 GPY10
G2 DQ1 L2 SD-A9 R3093 47
SD-DQ0 *B:A3,A7,B2,B8,D2,D8,E3,E7, R3039 15 SIN P11 P-ON-H1
G8 DQ0 F2,F8,H2,H8,J3,J7,N1,P9 H2 SD-A8 R3094 47
R3040 15 SCK T11 LED1
N1 SD-A7 R3188 22
R3041 15 BACKLIGHT-SW E2 BACKLIGHT-SW
K3 SD-A6
R3042 15 P-ON-H1 C1 BACKLIGHT-ADJ
2 R3043
R3044
R3045
15
15
15
M1
H1
M3
K1
SD-A5
SD-A4
SD-A3
SD-A2 GPIO4 T9
R3190
OPEN
R3095
R3201
2.2K
22
CPU-RESET-N
R3046 15
L1 SD-A1 GPIO5 R9
IC3006 R3047 15
R3102 J1 SD-A0
MX25L3205DM2I-12G 10K R3032 15
(MEMORY) P1 SD-BA2
L3004 R3033 15 USBDP R10
BLM21PG221SN1D K4 SD-BA1
R3104 1 CS VCC 8 R3034 15 USBDN T10
10K R3107 C3073 N2 SD-BA0 R3099 5.6K CONTINUE
10K 0.1 R3070 150 NU P10 DIGITAL 5
2 SO NU 7 H4 NU
P-ON+1.8V
3 WP SCK 6 P-ON+3.3V
C3072 10 AL+3.3V
4 GND SI 5 NU H14
C3071 0.1 P-ON+5V
R3206 22
SCL R12
R3207 22 CONTINUE
SDA T12 DIGITAL 3
R3479 CPU-RESET-N
10K
CONTINUE
DIGITAL 2
1 (USB JACK)
BUS-POWER
USBDN
USBDP
CN3009
1
2
3
C3246
1
D3052
OPEN
C3348
100/16V
IC3019
BD2224G-TR
(HIGH SIDE SW)
AUDIO-MUTE
SDA
SCL
GND 4 L3025 1 VIN VOUT 5
EXC24CG900U C3327
0.1 2 GND CONTINUE
R3204 R3203 DIGITAL 6
3 /EN /OC 4 L3041 4.7K 4.7K SDA
R3480 BLM21PG221SN1D C3175 C3176
10K OPEN OPEN SCL
DIGITAL MAIN CBA UNIT
S T U V W X
10-18 PL11.0SCDB4
Digital Main 5 Schematic Diagram [TYPE B]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
AUDIO SIGNAL CONTINUE
R3068 100 DIGITAL 3
PROTECT1
R3058 100
PROTECT2
DIGITAL MAIN CBA UNIT R3083 100
PROTECT3
DTV-ON-H2
DTV-ON-H1
P-ON-H2
*1 REMOTE
R3008 100
IC3005(5/6) VCOM-PWM
R8A05011BG-U0
R3010 OPEN
GPY10
CONTINUE
DIGITAL 4
P-ON-H1
*D VSS VCC33STB F12 LED1
VCC33STB G12 C3160 C3182 G
0.1 0.1 IC3004 BACKLIGHT-SW
VDDSTB E12 D S BD7820FP-E2 R3009 100
L3030 (+1.8V REG.) BACKLIGHT-ADJ
H13 AVSS12 BEAD Q3013 CPU-RESET-N
C3181 SSM3K309T L3015 C3004
L10 AVSS12 0.1 CONTINUE
CTL
VCC
GND
OUT
(SW+3.3V) BLM21PG221SN1D 1000P
VDD12 *C DIGITAL 1
C
G10 AVSS12
AVDD12 J13 1 2 3 4 5 REMOTE
G8 AVSS12
AVDD12 K6 C3121 C3122 C3123 C3124 C3125 C3126 L3001 AL+3.3V
G9 AVSS12 0.1 0.1 0.1 0.1 0.1 0.1 BLM21PG221SN1D
AVDD12 M11 P-ON+5V
E9 AVSS33 C3023 C3024 C3027 R3060 R3061
C3108 10 10 0.1 20K 33K P-ON+3.3V
D2 AVSS33 C3127 C3128 C3129 C3133 C3134 100/16V
0.1 0.1 0.1 10 OPEN CONTINUE
D3 AVSS33 R3059 DIGITAL 4
1K
D12 AVSS33 P-ON+1.8V
D5 AVSS33 L3016 P-ON+3.3V
BLM21PG221SN1D C3263 C3049
E7 AVSS33 VCCQ33 F5 1 100/4V AL+3.3V
VCCQ33 G4 C3157 C3158 C3159 L3043 BLM21PG221SN1D
E3 PD1 0.1 0.1 0.1 P-ON+5V
E4 PD1 VCCQ33 J12 Q3003 CONTINUE
VCCQ33 K13 2SC4081UBTLQ C3054 DIGITAL 2
D4 PD1 (SWITCHING) 1
3 E5 PD1
F10 VSSCLK
VCCQ33
AVDD33
L12
N11
Q3004
R3079 2SC4081UBTLQ
10K (SWITCHING)
R3077
10K
R3086
2.2K
R3084
P-ON+5V
AL+3.3V(2)
CONTINUE
DIGITAL 6
2.2K P-ON+3.3V
AL+3.3V(2)
L3014 CONTINUE
BLM21PG221SN1D R3017 DIGITAL 1
VCCQ18 H5 IC3007 100
OE2
VCCQ18 J5 C3264 C3079 BD7820FP-E2
0.01 100/4V (+1.8V REG.) LCD+12V
VCCQ18 M4 C3326 C3325 C3324 C3343 R3525 R3526R3524
10 10 10 10 OPEN OPEN OPEN
VCCQ18 M6 TO POWER SUPPLY
CTL
VCC
GND
OUT
CN3002 CBA CN301
C
VCCQ18 M7 29 VCOM-PWM
C3322 C3321 C3320 C3319 C3318 C3114 1 2 3 4 5
VCCQ18 M8 10 10 10 10 10 10 28 BACKLIGHT-ADJ
C3066A
VCCQ18 N6 OPEN 27 NU
VCCQ18 T1 R3110 R3011 100
C3140 C3141 C3142 C3143 C3144 C3145 56K R3111 C3075 26 BACKLIGHT-SW
0.1 0.1 0.1 0.1 0.1 0.1 42.2K OPEN C3005 C3006
C3060 C3060A C3068 C3069 C3070 R3109 R3014 100 OPEN 1000P 25 REMOTE
220/6.3V OPEN 10 10 0.1 4.7K 24 OE2
23 GND
L3020 R3531 C3011 C3008
BLM21PG221SN1D BC3001 OPEN 100P 100P 22 AL+3.3V
AVDD12 M10 C3066 C3076 C3052 C3053
220/6.3V BLM21PG221SN1D 10 10 0.1 R3424 D3103 21 AL+3.3V
C3135 100 1SS400TE61 R3050 C3015 C3016 20 P-ON+3.3V
0 10 0.1
2 AVDD12
AVDD12
AVDD12
E8
F8
F9
0.1
C3346
10
C3136
0.1
L3021
BLM21PG221SN1D
C3082
0.1
D3106
1SS400TE61
C3081
10
C3080
10
C3077
100/16V
L3003
BLM21PG221SN1D R3054
0 C3019 C3022
10 0.1
C3028 C3043
19 P-ON+3.3V
18 GND
17 GND
L3019 D3105 10 0.1 16 P-ON+7V
BLM21PG221SN1D 1SS400TE61 D3104
AVDD33 E10 1SS400TE61 15 PROTECT2
AVDD33 C2 14 P-ON+5V
AVDD33 C3 C3117 C3347 C3147 C3148 C3149 C3150 R3423 R3062
0.1 10 0.1 0.1 0.1 0.1 47K L3044 OPEN C3046 C3045 C3047 C3044 13 P-ON+5V
AVDD33 E11 BLM21PG221SN1D 1000P 10 0.1 1000P
12 GND
Q3101 11 PROTECT1
L3026 2SC4081UBTLQ R3100 R3106
BLM21PG221SN1D (SWITCHING) 22K R3105 22K 10 P-ON+3V
ADAC D6 C3265 1K R3072 100
C3151 C3154 10 9 P-ON-H1
0.1 0.1 L3029 Q3006
BEAD R3097 2SA1774TLQ R3464 8 AMP(R)-OUT
AADC E6 2.2K (SWITCHING) OPEN C3048 C3055
OPEN 1000P 7 GND
C3152 L3028 Q3005
0.1 BLM21PG221SN1D 2SC4081UBTLQ 6 AMP(L)-OUT
VDDCLK G11 IC3008 (SWITCHING) D3101 5 PROTECT3
C3091 BD9329EFJ-E2 1SS400TE61
1000P (DC-DC CONVERTER) C3083 4 AUDIO(R)-OUT
C3139 D3102 C3062
0.1 0.022 1SS400TE61 1000P 3 GND
1 BST SS 8
R3141 2 AUDIO(L)-OUT
*C:G5,G6,H6,J7,J11,K7,K11,L8, R3101 100
L9,M9,N9,P9 10 2 VIN EN 7 1 P-ON-H2
C3085 C3090
CONTINUE *D:F4,F6,F7,F10,F11,G7,H7~H12, 0.1 1 C3067 CONTINUE
3 SW COMP 6
1 DIGITAL 3
P-ON+3.3V(2)
CONTINUE
J6,J8~J10,K5,K8~K10,K12,
L5~L7,L11,P2,T8
L3009
22uH
4 GND FB 5
R3137
16K
C3088
1500P
R3133
10K
1000P
R3087 100
DIGITAL 1
P-ON+3.3V
CONTINUE
DIGITAL 3
DIGITAL 6 AUDIO(L)-OUT
P-ON+3.3V(2) R3085 100
D3001 C3094 C3097 C3096 R3149 D3002 AUDIO(R)-OUT
SK22A 47/4V 10 10 5.6K OPEN R3078 100
AMP(L)-OUT
R3145 R3074 100
12K AMP(R)-OUT
AL+3.3V
R3143 C3057 C3061 C3063 C3065
47K 1000P 1000P 1000P 1000P
Y Z AA BB CC DD
10-19 PL11.0SCDB5
Digital Main 6 Schematic Diagram [TYPE B]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
CONTINUE
DIGITAL 5 L3046 HDMI-
BLM21PG221SN1D JK3002 CONNECTOR-3
P-ON+3.3V
C3316 C3310 C3311 C3312 C3313 C3314 C3315 C3300 C3301 C3302 C3303 C3304 1 TMDS-D2(+)
AL+3.3V(2) 10 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 0.01 0.1 2 D-SHIELD0
3 TMDS-D2(-)
C3331 C3332 C3333 C3334 C3305 C3306 C3307 C3308 C3309 4 TMDS-D1(+)
0.1 0.01 0.1 0.01 0.01 0.1 0.01 0.1 0.01
5 D-SHIELD1
6 TMDS-D1(-)
7 TMDS-D0(+)
4 *1
IC3005(6/6)
R8A05011BG-U0
DIGITAL SIGNAL PROCESS
8
9
10
11
D-SHIELD2
TMDS-D0(-)
TMDS-CLOCK(+)
C-SHIELD0
/MAIN MICRO CONTROLLER Q3014
2SK3018T106 R3405 12 TMDS-CLOCK(-)
(BUFFER) 100
13 HDMI-CEC
TO DIGITAL TO DIGITAL R3415 14 NU
MAIN 2 MAIN 3 82K
IC3005(2/6) IC3005(3/6) D3057 R3486 15 HDMI-CLOCK
RB751S-40TE61 4.64K 16 HDMI-DATA
VIDEO AUDIO IC3018 R3275 R3278 R3387 17 GND
DECODER DECODER 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 BU16029KV-E2 47K 47K 0
R3237 (HDMI SW) 18 +5V
GND
VCC
GND
VCC
GND
NU
27K C3262 R3411 R3370 19 HOT PLUG DETECT
HDMI-CEC B15 1 2.7K 1K
17 HOT-PLUG- 64 R3371
DETECT3 R3412 OPEN
18 63 OPEN
3 24
25 VCC
26
HDMI SW 57
56
VCC 55
6
7
8
TMDS-D1(-)
TMDS-D0(+)
D-SHIELD2
9 TMDS-D0(-)
27 54 10 TMDS-CLOCK(+)
R3488 R3487
4.7K 4.7K 11 C-SHIELD0
28 GND 53
12 TMDS-CLOCK(-)
HDMI1-SCL C16 29 SCL-SINK 52 13 HDMI-CEC
14 NU
HDMI1-SDA C15 30 SDA-SINK 51
15 HDMI-CLOCK
HDMI1-HPD D14 31 HOT-PLUG-
DETECT-SINK
HOT-PLUG- 50
DETECT2 16 HDMI-DATA
R3508 R3274 R3277
22 17 GND
HOT-PLUG-
HDMI-SEL0 G3 32 HDMI-
SEL0 NU 49 47K 47K
DETECT1
R3496 18 +5V
HDMI-
4.7K C3260 R3409 R3374
SEL1
HDMI-SEL1 F1 1K 19 HOT PLUG DETECT
VCC
GND
VCC
1 2.7K
NU
R3509 R3497
22 4.7K 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 R3375
R3414 OPEN
OPEN
Q3032
R3406 2SC4081UBTLQ
1K (SWITCHING)
D3065 R3385 HDMI-
1SS400TE61 10K JK3003 CONNECTOR-1
R3270 C3187
2.2K 2.2 1 TMDS-D2(+)
EXT-RES C4 C3186 2 D-SHIELD0
2 PLL-XFC-A B5
PLL-XFC-P A5
4700P
R3271 C3188
3K 2200P
3
4
5
TMDS-D2(-)
TMDS-D1(+)
D-SHIELD1
6 TMDS-D1(-)
7 TMDS-D0(+)
R3236 C3185 8 D-SHIELD2
560 0.01 9 TMDS-D0(-)
10 TMDS-CLOCK(+)
11 C-SHIELD0
12 TMDS-CLOCK(-)
PWR M12 13 HDMI-CEC
14 NU
15 HDMI-CLOCK
16 HDMI-DATA
R3293 R3294 D3066 R3273 R3276 R3388 17 GND
10K 10K 1SS400TE61 47K 47K 0
18 +5V
CONTINUE R3301 R3372
DIGITAL 5 R3477 R3478 R3512 33K 1K 19 HOT PLUG DETECT
R3303 0 0 0 C3261 R3410
P-ON+3.3V(2) 1.5K 1 2.7K
R3373
R3304 C3213 R3413 OPEN
10K IC3011 0.1 OPEN
BU9883FV-WE2
R3302 Q3301 (HDMI SERIAL EEPROM)
10K 2SC4081UBTLQ Q3031
(SWITCHING) 1 VCC1 VCC2 16 2SC4081UBTLQ
R3407 (SWITCHING)
C3190 1K
1 2 SCL1
3 SDA1
4 WPB
SCL2 15
SDA2 14
NU 13
0.1
R3383
10K
CONTINUE
DIGITAL 2
R3523 C3192 0.1 R3507 OPEN
CONTINUE 10K R3282 5 VCC-OUT GND 12 P-ON+5V(1)
DIGITAL 4 100 R3476 OPEN VGA-SDA
SDA R3281 6 SDA0 SDA3 11
100 R3475 OPEN VGA-SCL
SCL 7 SCL0 SCL3 10
8 VCC0 VCC3 9
C3191 C3212
0.1 0.1
DIGITAL MAIN CBA UNIT
EE FF GG HH II JJ
10-20 PL11.0SCDB6
Power Supply CBA & Jack CBA Top View
Because a hot chassis ground is present in the power supply CAUTION !
circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire,
Also, in order to have the ability to increase the input slowly, If Main Fuse (F601) is blown , check to see that all components in the power supply replace only with same type 4 A, 125V fuse.
when troubleshooting this type of power supply circuit, circuit are not defective before you connect the AC plug to the AC power supply. 4A/125V ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
a variable isolation transformer is required. Otherwise it may cause some components in the power supply circuit to fail.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
Jack CBA Power Supply CBA
BA01F2F0102 7 B
BA01F2F0102 7 A
C7A3 A3
R236
C225
R245
D406 D405 R405 Q201
1 9
J163
GND
CL701B
J316
J300
R235
PROTECT3
GND
GND
D210
R244
C224
D202
BL-ADJ
D207
J298 LCD 24V
C219
D208
JS202
J320
GND
D420
R249
C204
Q205
OE2
R203
Q210
D667 J289 GND D203
R240
J337
JK753
R223
LCD -6V
Q401
C210
J292
R224
J372
J315
J385
R243
GND
JK754
Q211
R228
R229
J239 C501 J373
J317
GND
GND
Q207
GND
J241 J374 +36V C403
R212
JK751
JK752
R204
J268
JS203
R237
D205
C223
R239
R238
D206
GND
PROTECT1
Q212
Q202
GND
D416 J378 INV+13V
Q208
-7V
LCD -6V
J314
GND
J269
J309
CN201
Q501 D401
J375 PROTECT2
BL-SW
15
14
J312
JS631 JS633
J264
J366
J376
J371
J301
GND
D201
Q203
Q402 LCD+16V Q631
JS201
C650
R658
D419
D654
R254 R649
+36V
J379
J307
J303
J299
C220
C222 R645
Q206
Q204
J291 GND
R650 D675
LCD 16V
1 2 3 4 5 6 7 8 9 10
J306
J384 D211
J288
D423 J359 GND
J297
J380
R210
GND J381 LOW-VOL PROTECT
TOOL NO.
R655
R653
J284 GND
C646
LCD+3.3V
J369 ALL+6.0V
R639
D653
R638
R637
JS630
R646
Q634
D651
D650
4
J286
1 IC601
C692
D652
J386 GND
C675
J389
GND
GND
J391
GND
1
J390
2
J387 GND
FB
Q209
D204
R227 J383 C631
LCD+16V C637 D639 D622
2 3
R696 J377 R618
LCD+16V
50
C632
R2
R247
D635
4
D638
R253
C609 D610
R697
C638
D403
13
Q213
R622
D619
J319
R501
D6
J267 +15Vfor13VLCD
R624
+15Vfor13VLCD R619
C608
12
D608 Q603
R695
Q636
D6
D609
GND
D209
R667 J339 +15Vfor13VLCD 14
BC602 D6
R502 D631 R621
R242
J263
C611
R666
J290 AMP+12V
R657
1
D407
D61
R661 D606 R626
J365 +6.7V
R407
J396
D412 D607
J351 +6.7V D632 BC603
R625
D647
C610
R627
T601
D66
Q635 J388 GND
R662
R660
DRIVE OUT
Q604
C613
C615
D658
D673
C614
JK731 J278 GND
R663
C645
GND
J392
R636
R613
D657
GND
R612
J393
HV
J361
D633
GND
J370
R406
D662
J394
BC601
IS
J362
R664
HOT+15V
J246 3.5Vfor1.8V C606
GND
J363
D637
D659
R665
J149
D648 D6
17
J364
D404
C633
C640
D616
C647
J395
D620
R635 J353
D643
J352 GND
JK732 J242 R609 R611
J237 Q601
J399 LOW-VOL PROTECT
J356
J355
J357
COMP-Y R610
R606
CL701A
C642
C607
9 P-ON-H1
J235
P-ON 3.3V
GND
GND
D615
J234
D642
C658
D641
VT 31V
COMP-Pr
LCD 16V
J228 GND J229 J238
C691
J232
V-L
V-R
D646
R763 A-OUT-MUTE Q871 J227 GND
J224
GND
JK733
J225
J226
Q874
R672
Q873
J222 J216
S-Y
J217 A-MUTE
R791
C648 COMP-L
R790
R788
OPAMP 9V
V-L
J214
J218
J190 SEL-L J213
D649
D664
A-OUT-L GND
J347 ALL+3.3V J215 AMP 13V
V-R
GND
GND
C771
J185 SEL-R
J205
J204 PROTECT1
HDMI-L
J195
R603
JK871
J210
J207
R674
J206
J182 J202
J200
JK741
OPAMP 9V
R878
SW 9V
GND C880
J178 INPUT1
J346 J194 C652
J191 AOUT-L
GND
J199
J196
R673
A-OUT-R
Q772
R686
J177
J173
Q638
J184 AOUT-R
R780
D621A
3
GND
Q872
R677
1
J341 J368
CN602
J354
R771
J171
D603
GND
Q639
D602
D410
R781
6.7V
D666
Q771
P-ON-H2 R702
GND
D411
J183
GND
R605
L871
JK742 R689
J188
HDMI-L
HDMI-R
J180
PC-R
C676
J192
PC-L
2
D621B
D665
J176
J172
P-ON 9V R701 R693
2 BC301
J164
R691
L301
Q642
GND
GND
J350
D671
GND
J349
J170
J169
C604
J165 VT 31V
TUNER 5V
J166
JK721
R685
R682
R683
TUNER 5V
D303
CN302
R698 J150
Q641
J153 Q643
J156
1
ALL3.3V
R687
JK711
P-ON+5V
JS303
C655
D604
RISK OF FIRE-
C306 J160 P-ON 5V
C303
C654
Q640
D302
D645
C823 L602
D301
J159 TUNER 5V
J158
C656
GND
J154
J161
J342 J157 GND
Q801
28
C653
D415
JK722 J155 GND
D601
29
J151 SPDIF
RESET
BC841
J152
GND
C844 D409
J148
J343
J147
KEY-IN1
C601
L601
GND
COLD
J146
L802
J136 AMP+12V
J143 C832
Q841
L801
1
SA60
ALL+3.3V
D421
J382
GND
P-ON-H1
FH602
J144
J145
GND
J358
J330
R402
J129
GND
1
R821 D806
GND J124 P-ON 5V
4A/125V
3.5Vfor1.8V
C831
D414
2
PROTECT3
J323
01
J131 GND
GND
R6
J139
PROTECT2
TUNER
A-MUTE
J142
J110
J127
D413
3.5Vfor1.8V
J132
J137
D418
J128 GND
J141
D417
A S
J125
GND
J126
J130 ALL3.3V
1 J123 GND
F601
R819
9V
J114 GND
VCOM-PWM
J133
P-ON-H2
C602
J134
GND
PROTECT1
BL-ADJ
KEY-IN1
C801
FH601
BL-SW
GND
J112 GND
ALL3.3V
J135
HOT
OE2
J113
J340
6.7V
P-ON 3.3V
TM601
J118
ALL+3.3V
J121
J120
R700
J122
J119
J108
J115
J117
BC803
CN301
C694
BC802
J140
R699
C693
GND
P-ON 5V
AMP+12V
J345
1
J111
TU301S
C815
60
CN
C816
D6
74 J107
GND
GND
J106
GND
J116
C819
AC601
J344
D807
D676
GND
D804
28
J322 CN801
ALL3.3V
J102
29
CN101
J103
D801
1 5 J101 CN802 BC804 GND
GND
J328
GND
J105
D803
J104
AMP+12V
AMP+12V
C827
D802
BC805 L803 L804
TM602
A B C D E F G
10-21 BA01F2F01027
BA01F2F01027
circuit, an isolation transformer must be used when repairing.
Because a hot chassis ground is present in the power supply
PIN 15 OF
PIN 17 OF
PIN 19 OF
PIN 13 OF
PIN 4 OF
PIN 8 OF
PIN 6 OF
CN302
CN302
CN302
CN302
CN302
CN302
CN302
WF4
WF1
WF2
WF5
WF6
WF3
WF7
JK751
4
J148
D664
C648
RESET 1
J146
29
KEY-IN1
R697
C649
J346
1
GND
29 J382 2 J141 28
J347
J348
CN301
GND
GND
J140
C658
J182
CN302 J126
R667
GND J203
ALL+3.3V
ALL+3.3V
J152 3.5Vfor1.8V
C752
GND
J113 R699
J173
J167
R751 GND
J222
R663
S-Y
J185
J190
C681 C683
SPDIF
C755
R635
1
R757 R660
J217
GND
R302 D301
A
R756
R763
SEL-R
R666
J178
J175
BA01F2F0102 7
SEL-L
J342
R662
R664
A-MUTE
C311
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
C753
D637
R304
ALL3.3V
BC301
R311
D660
JS303
R774
D659
GND J162
CL701B
Jack CBA
R665 R777
JS301
J199 C308
1
R779 C775
S A
D659A J177
R306
GND
9
TUNER
C640 J349
Q635
Q636
CN101
J355 R771
5
J187
C771
CAUTION ! : For continued protection against risk of fire,
C757 GND
R761 J149 V-L VT 31V C305
R636 SW 9V J165
C761 J356
GND R773 C301 R895
J158
PC-L
R790 R782
1
J230 R781
R789
VT 31V
IC771
D676
B
C647 R780
J239
GND
D66
9
8
1 L301
Q873
R792 SW 9V J196 J343
GND
HDMI-R J169
J234 C773
JS201 ALL+3.3V
D403
P-ON 3.3V J195 R784 HDMI-L J170
D657 J364 SPDIF J151
GND R887 D413
R227
D412
R793
The voltage for parts in hot circuit is measured using
HDMI-L
R661
J241
PROTECT1
J134
74
Q401 R231 C221 GND J363 R715
D416
Q501
D6
C701 PROTECT1
JK721
JK722
R785 R723
R254
D211
Q874
A-OUT-L
R713
COMP-L
J133
J216
R786
R404 D204
J237
COMP-Y
JK872
COMP-Pr
COMP-Pb
P-ON-H2
J235
J233
J213
C724
6.7V J115
J229
Q213 C871
A-OUT-MUTE
R721 R724
C501
J385 C841
R732 C732 R741 BL-SW J120
D401
C733
GND R411
JK731
JK732
JK841
BL-ADJ J121
Q209
R742
D667
VCOM-PWM J122
J189
R843
A-OUT-R
R842
D406
D423
J168
P-ON 9V
C
R247
J372
J378
9V J118
J374
J383
C704
Q402
3.5Vfor1.8V
J375
R410 J135
1
C702
INV+13V
R412 C873
TUNER 5V
R502
R716
J298
+15Vfor13VLCD
J369
Q841
J381
C875 D671
PROTECT2
GND
4
IC871 PROTECT3
J386
J387
R405
J289
10-22
ALL3.3V J130
ALL+6.0V
LCD 24V
R879
J292
J359
+36V
J373
J376
J351
J365
LOW-VOL PROTECT
C884
LCD+16V
J290
D404 D670
GND
C885 C656
LCD+16V
R402
CN802 J101
GND
J278
J388
LCD -6V
J137 R813
J232 R885
GND
GND
R881
AMP+12V
C657
GND
D421
C836 C835
PROTECT2
J267
J339
C844
R819
GND
GND
C879
D410
R689
C880
D414
+15Vfor13VLCD
+15Vfor13VLCD
C837
J246
D210 R687
J186
J184
J191
D411 D418
D648
C815 C846
R244
J111 D804
J204
R403
R821
GND J366
GND
AOUT-L
AOUT-R
J142
J223
J155
R816
J157
GND
J227
J316
J211
J215
3.5Vfor1.8V
J238
J399
J116
P-ON-H1
-7V
A-MUTE
J263
GND
J153
R894
PROTECT1
J159
J300
J160
4A/125V
GND
GND
GND
GND
R659 J341 R690
ALL3.3V
R872 D803
R243
P-ON-H2
C816
LCD 16V
AMP 13V
GND D417
C874
A-MUTE
R654
NOTE:
D806
-7V J264 C876
TUNER 5V
R892
P-ON 5V
C801
BC805
D209
BC804
J145
C645
R886 C817
J360
J212
GND
J194
P-ON 3.3V
R658
J242
R644
J174
D649 J110
J202
R655
R401
LOW-VOL PROTECT
GND
D665
6.7V
P-ON-H1
6.7V
D807
6.7V
C814
J147
GND J206
C633
R241 R807
D
J269 D419 R653 D415 R818 R804
GND J207
R693 R701
R702
R698
R647
C631
R409
J353
J127
GND
R242 Q801 R808 C830
D651 D639A
R652 J171 C803
R240
R672 R674
JS631
C654 R820
C403
42
GND
C646A R673 6.7V R809 C820
L803
J390 C809 C828
D655
C829
C646
L801
D420
C644
R677 C805
D652A J104
Q643
C825 AMP+12V
D631
J317
C637
D635
Q631
IC801
C832 J143
R691
C652
P-ON+5V C804
GND D652 Q641 J161 C818 J144 C807 C826
D647
J188
D633
C642 J105
R817
R228 C650 C808 C822 AMP+12V
D208
D203
GND
If Main Fuse (F601) is blown , check to see that all components in the power supply
R680 L802
GND
D644A C810 C821
Q637
R229 C650A
D632
D644
D643 D666 R408
D653
21
R225 C806
D639
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
22
D654
circuit are not defective before you connect the AC plug to the AC power supply.
J354
R638 D646
D409
R223 R641
R637 R802 R812
R651 R679 J172 R643
T601 R682
R645
D638 C651
Otherwise it may cause some components in the power supply circuit to fail.
R639 R642
L804
R683 R803 R811
D639B Q639 BC803
Q207 D641
R678
R646
J136
J112
R226
GND J123
GND J114
R668 R675 R685
J128
JS630 D642 C811 C831
J164 D645
C638
GND
R686 R676
AMP+12V
GND
J107
R649
R650
BC802 C827
J389
Q208
C655 AMP+12V
R224
GND C676
1
GND J106
Power Supply CBA & Jack CBA Bottom View
J315
E
C823
J371
GND J367
R235 C691 C641
IC601
GND
GND
COLD
GND
D802
J368
J176
JS202 J268
GND
J323
J150
GND
OE2 GND
C639
13
GND J337 D6
BC602
4
R237 D801
BC603
R617
BC601
12
C223 D6
Q210
R236 R239 J391 C615
14 C611
FB
C694
R238 D6
C225 J394
D205A
C607
J322
GND
R245 D205 IC602 C614 D603
4
5
IS
Q601
C838
D206
D622
C206
HOT
J314
C602
1
R201 GND D61 C613
R248 1
CN801
Q212 D602
R618
J392
R249 R202 DRIVE OUT R605
17
C207
D6
R612
D610 C609
J320
L602
D616
R609
C693
R610
D202 R206
JS633
C839
Q201
R611
C606
R207 D675
GND
R619
F
R203 R205 R613
C610
R204
C204
C604
D615
C216 C208
R213 GND J312 GND J291 GND D620 R606 D621A
R215 J396 J393
R214 GND J284 HV R603
C209 R607 R604
S
R219
Power Supply CBA
J301 J370
Q205 J297
Q602
Q206
R218 J306 C608A
C603
R220
R217 R222
C605
C608
LCD 16V C675 D621B
C220
D604
8
1
D607
R210
R221
5 JS203
IC201
R620
L601
D608
D601
C218 C217 AC601
R621
R216
4
R212
Q203 C692 R622 D607A C601
D606
C219
C203
Q204 D619
J163 C210
J288 LCD+3.3V R625
GND C212 R624
CAUTION !
C213 R208
J307
PROTECT3 1
C214 R211 J303 3 2 1 SA60
BL-ADJ
G
Q604
Q603
C202 C215 R209
1
60
14 2
F601
CN
CN201 R627 FH602
01
R6
R626
R623
15 1 HOT+15V J395
J309 CN602
LCD -6V GND
C201 J286
BL-SW J299 FH601
4A/125V
Inverter CBA, Function CBA & IR Sensor CBA Top View
Because a hot chassis ground is present in the power supply NOTE:
circuit, an isolation transformer must be used when repairing. The voltage for parts in hot circuit is measured using
Also, in order to have the ability to increase the input slowly, hot GND as a common terminal.
when troubleshooting this type of power supply circuit,
a variable isolation transformer is required.
C7A3/A3 C7A3 A3 / / /
CL101B
SW107B SW106B SW155 SW105B SW154 SW104B SW103B SW101B D101
C151
GREEN RED ORANGE
CL103C
AGING
R156
VOL RS101
D109
CH
D151
UP VOL CH POWER DVD
POWER
DOWN
R123
R124
UP
4 DOWN STB BY RS102 D106
CL103B
CL103A
R155
D108
GND
PATTERN MENU R109 R152
R115 D104
R151
R101
STD BY D105
R113 R112 R111 R108 C113
D107
C108
BA17F4F0103 1 B R153
R114 TOOL NO.
SW107A SW106A SW105A SW104A SW103A SW151 J101 SW101A
SW153 R154 SW152
1 2 3 4 5 6 7 8 9 10
R127
CL102B
R128
C101
VOL
STOP
UP
CH
UP
EJECT
POWER
DOWN
DOWN
MENU
PLAY
C7A3 A3
VOL
CH
J102
BA17F4F0103 1 D BA17F4F0103 1 C
J1005
GND
J1004
GND
J1003
GND
3 C7A3 A3
BA17F4F0103 1 A
J1022
PROT4
SW2
SW2
J1020
J1021
PROT5
J1023
PROT2
PROT3
J1013
J1012
J1010
J1011
SW2
SW2
SW1
SW1
J1006
J1007
J1008
J1009
C1701 C1700
J1014
J1015
SW2
PROT4
PROT5
J1024
SW2
COLD
D1705 J1025
J1110
J1111
J1112
J1113
D1701
R1704
R1709
D1702
D1706
J1026 C1906
GND D1961
J1027
D1700
J1028
D1703
HOT
PROT4
PROT5
GND GND
D1960
2
PROT6
J1032
J1030 LN2
D1704
J1031 NH2 D1707
1
BC1931
J1033
J1034
J1035
J1036
2
R1130
R1150
J1037
LN1
NH1
LN2
NH2
SW2
10 CN1003
GND
C1993
SW1
GND
PROT6
J1044
J1046 PROT3 BC1930
GND
J1054
VS6
J1039
J1040
J1045
J1041
J1042
J1038
J1049 PROT2
J1047
R1143
J1058
R1103
R1146
D1994
R1127
J1048
C1930
R1147
VSEN
J1050 J1051
D1930
11
J1053 GND
C1994
J1056 PROT1
J1091 Q1930 J1055
C1990
R1106
REG 7.5V
J1059
J1063 PROT
+24V
+24V
C1206
+24V
BST2 R1937
D1301
VSEN
J1069
C1304
J1066
J1064
J1065
J1061
J1068
VS2
PROT
R1939
J1072
SW1
J1071
J1067
C1302
D1934
VS4
REG 7.5V
DC12V
J1074
J1076
J1002
J1077 GND
J1073
NH1
D1991
LN1
J1078
J1075
D1931
J1060
R1148
R1118
R1145
R1115
R1930
J1079
R1936
D1932
GND
R1933
R1934
R1932
R1949
DUTY
J1081
R1935
J1085 +24V
1
FAIL
D1970
GND
J1087
PROT
GND
D1200
J1090 +24V
J1099
J1088
D1972
J1001
GND
IC1930
R1967
J1086
R1938
GND
J1092
D1971
R1970
R1931
J1093
JS1200
D1202
J1082
J1083
J1103
REG 7.5V
GND
J1095
D1973 Q1931
J1097
BL-SW
J1098
J1096
BL-SW
J1101
GND
+24V
J1102
J1100
PROTECT3
J1104
CN1900
VSEN
J1080
CN1901
PROTECT3
BL-ADJ 2 14
C1982
IC1931
J1105
D1203
J1120 CN1001
1 15 C1983
J1108
GND J1107 BL-SW
A B C D E F
Inverter CBA
10-23 BA17F4F01031
BA17F4F01031
3
1
4
VOL
DOWN D1508
BA17F4F0103 1
J1003
GND
SW107A
R1128
UP
VOL
R1134 J1082
R1115 D1507
C1114
R1147 R1116
R1133
SW106A
R1125
B
R1513
R1131 J1060
GND
C1501
J1028
R1146
GND
J1026
R115
R114
R1130 J1083
J1061 R1113 C1120 R1516
R1114
R1150 D1506 R1308 C1502
J1077
PATTERN
R1103 Q1301
C1301 R1514
CH
R113
R1102 Q1303
DOWN R1143 R1310
GND
R1101 J1097
R156
T1102
BL-SW
R1303
SW104A
J1071
PROT6 J1048 R1220 J1075
MENU
LN1
REG 7.5V
CN1102
D1201
R1703
Q1701
SW103A
D1702 J1095
J1072
DC12V
C1208
SW154
R111
EJECT
24
SW2 J1038
1
R1226
R109
SW104B
SW153
Q1203
D1203
R1204
13
12
R1227
C1112
R154
J1109
R155 R1701
CH
DOWN
R1511 C1202
D1502
R1510 C1206
R1207
B
C1500
R153
SW152
SW103B
R152
PROT
R1501 C1214
R1205
Q1202
J1081 R1200
J1020 R1503 R1202
J1110 D1700 J1033 R1203 Q1201
C1201 DUTY
R1502 R1214 R1208
J1021 J1034 D1500 PROTECT3
PROT5 J1111 C1302 R1209
R151 PROT5 PROT5 R1507
D151 PLAY J1022
C1207
PROT4 J1112 J1035 R1213 C1211 J1105
POWER PROT4 PROT4 R1506 J1068
J1036 D1501 PROT R1212
J1113 R1505 R1500
SW151
C1303
D1300
PROT R1215
Function CBA
FAIL J1086
R108
J101
R1508
J1030
J1031
POWER R1509
D1301 Q1300
C1701
C151
D107
R1309
LN2
NH2
C108
J1102
BL-ADJ
SW101A
R1708
R1305
J1050
J1053
J1056
J1049
C1707
J1120
GND
J1046
C1939
D1707
J1043
Q1703
PROT1
PROT2
C1938
C1110
PROT3
C
+24V J1066
2
CL103B
1
J1024 R1707 +24V J1064
SW2 D1706
+24V J1065
J1098
C1708
PROTECT3
J1108
J1088
J1084
SW2 J1025 D1705
R1709
C1304
J1107
R1706
CL103A
RS101
GND
GND
14
C101
Q1702
C1706 C1305
C1935
BL-SW
D1704
J1096
15
CN1001
R1705 BL-SW
C1936
The voltage for parts in hot circuit is measured using
C1103 J1099
GND
C102 C1102 C1702 C1937
J1037 J1103
C1994
10-24
GND
D1991
STB BY
BC1301
T1101
D108 GND
C1700
D101
D1992
IR Sensor CBA
C104 J1092
D1990
GND Q1972
CN1101
C1993
R103 R101
J1090
C103
D109 SW2
J1010 C1990
hot GND as a common terminal.
D1973
R1973
R106 J1011 GND
C1983
R1972
J1085
CL102B
+24V
R1988
D
D1971
D1994 R1982 R1987
R1977
C1108
R1979
R1986
R1980 Q1970
J1101
+24V
Q1971
BA17F4F0103 1
T1950
Inverter CBA, Function CBA & IR Sensor CBA Bottom View
PROT3 J1007
H.V. CAUTION
NOTE:
PROT2 J1008
J1027
GND
R123 R1967
C114 J1009
C1982
R1970
C113
J1104
D104
C110
GND
POWER
C1905
R1981
IC1930
R128
C1981
R124 C1934
STD BY
R127
C1906
C111 D1932
C115
C112
R126 R1936
circuit, an isolation transformer must be used when repairing.
D105
Because a hot chassis ground is present in the power supply
J1069 R1935
IC1931
R125
C1106
E
R1931
A
C1932 R1934
DVD
R1933
when troubleshooting this type of power supply circuit,
D1931
D106
BC1930
SW2 J1078
D1933
J1013
Q1931
C1930 R1941
SW2
Q1930
BC1931
COLD
R1939
Q1932
HOT
Not Used
C1933
a variable isolation transformer is required.
R1930 R1938
CL103C
GND J102 D1934
CN1901
R1951 R1952
J1089
T1100
J1073 R1949
C1101 C1931
CL101B
R1937
C1100
CN1900
R1950 D1930
CN1100
R1940
GND
J1051
F
C1910
Inverter CBA
C1104
J1005
GND
1
J1055
11
2 CN1003 10
D1960
D1961
J1093
WAVEFORMS
11-1 LC9NWF
[TYPE A] [TYPE B]
CN301 CL3701 CN3701 CN3002 DIGITAL MAIN CBA UNIT
1 P-ON-H2 1
2 AUDIO(L)-OUT 2
COMPONENT 3 GND 3 [TYPE A]
-Y-IN CN3902
4 AUDIO(R)-OUT 4 CN1100
POWER SUPPLY CBA CN201 CL201 CN1001 [TYPE B]
5 PROTECT3 5 1 BACK
COMPONENT 1 GND 15 CN3005
-Pb-IN 6 AMP(L)-OUT 6 2 LIGHT CL3902
7 GND 7 2 INV+13V(NU) 14 STV 1
TU301 TUNER UNIT 3 GND 13
COMPONENT 8 AMP(R)-OUT 8 XAO 2
-Pr-IN 9 P-ON-H1 9 4 BACKLIGHT-ADJ 12 CN1101 OE1 3
10 P-ON+3V 10 5 BACKLIGHT-SW 11 1 BACK CPV 4
6 PROTECT3 10 2 LIGHT POL 5
11 PROTECT1 11
COMPONENT- 7 GND 9 HDMI-
AUDIO(L)-IN 12 GND 12 TP 6
CONNECTOR-1
13 P-ON+5V 13 8 LCD+13V 8 GND 7
CN1102
14 P-ON+5V 14 9 LCD+13V 7 LLV5(-) 8
COMPONENT- 1 BACK
AUDIO(R)-IN 15 PROTECT2 15 10 VGH 6 LLV5(+) 9
2 LIGHT
16 P-ON+7V 16 11 GND 5 LLV4(-) 10
17 GND 17 12 P-ON+3.3V 4 LLV4(+) 11
HDMI- HDMI-
18 GND 18 13 LCD-5V 3 LLV3(-) 12
AUDIO(L)-IN CONNECTOR-2
19 P-ON+3.3V 19 14 VCOM 2 LLV3(+) 13
20 P-ON+3.3V 20 15 GND 1 GND 14
HDMI-
AUDIO(R)-IN 21 AL+3.3V 21 LLVCLK(-) 15
22 AL+3.3V 22 CN602 CN1901 LLVCLK(+) 16
DIGITAL 23 GND 23 +B 1 1 +B GND 17 HDMI-
AUDIO-OUT 24 OE2 24 HOT-GND 2 2 NU LLV2(-) 18 CONNECTOR-3
(COAXIAL) 25 REMOTE 25 HOT+15V 3 3 HOT-GND LLN2(+) 19
26 BACKLIGHT-SW 26 4 HOT+15V LLV1(-) 20
AUDIO(L)
27 LED1(NU) 27 CN1003 CL1003 LLV1(+) 21
-OUT
28 BACKLIGHT-ADJ 28 1 GND LLV0(-) 22 USB JACK
AUDIO(R) 29 VCOM-PWM 29 2 LCD+13V LLV0(+) 23
-OUT [TYPE A] [TYPE B] 3 LCD+13V GND 24
CN302 CL3702 CN3702 CN3006 4 VGH
1 GND 1 5 GND
12-1
2 SPDIF 2 6 P-ON+3.3V
3 GND 3 7 P-ON+3.3V
4 VIDEO-IN 4 8 LCD-5V
5 S-VIDEO-SW 5 9 GND
6 S-VIDEO-C-IN 6 10 VCOM
7 GND 7 LCD MODULE
INVERTER CBA 11 GND
8 S-VIDEO-Y-IN 8
ASSEMBLY
9 GND 9
10 INPUT1 10
11 AUDIO(R) 11 CL701A CL701 CL701B
VIDEO-IN
12 INPUT0 12 1 S-VIDEO-Y-IN 1
AC601
WIRING DIAGRAM
PL11.0WI
EXPLODED VIEWS
Cabinet
L19 CL201
A1 Power Supply CBA
B46 L17
L34
L17
A15
B34
B34 CL1003
L19
A42
CL3702 X7
AC601 A2
CL3701 L19 S6
L1
B27 B22
X6 L33
A41 L33
L1
Digital Main CBA Unit
L23
B24 B22
L19
IR Sensor CBA B1
A4 A8
A5 Function CBA
L19
CL3902 L1
L23 S6
B18 B5
B18
L33
CL802 L15
A12 S6
CL801 L33
See Electrical Parts List
for parts with this mark.
SP802 Stand Assembly
L42
13-1 PL11.0-A_CEX
Packing
X14 X2
X4 X12 Tape
X3
Tape
X1
Packing Tape
S3
Stand Assembly
S5
Packing Tape
FR
S7 ON
T
S6
S1
S17
S4
32PFL3506/F7 (XA1)
CARTON
13-2 PL11.0PEX
TYPE A
PARTS LIST
[32PFL3506/F7 (Serial No.: DS1), 32PFL3000/F8 (Serial No.: XA1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No.
# have special characteristics important to safety. ACCESSORIES
Before replacing any of these components, read STAND SCREW KIT A17F6UH 1ESA28477
carefully the product safety notice in this service X1 BAG POLYETHYLENE 235X365XT0.03 0EM408420A
manual. Don't degrade the safety of the product X2# OWNERS MANUAL A17F6UH 1EMN28039
through improper servicing. X3 REMOTE CONTROL TRANSMITTER YKF259- URMT34JHG001
001
NOTE: Parts that are not assigned part numbers X4 BATTERY R03-B500/01S XB0M451CZB01
(---------) are not available. X6 QUICK START GUIDE A17F6UH 1EMN28041
X7 REGISTRATION CARD(PHILIPS) A11P4UH 1EMN27321
X12 CABLE MANAGEMENT TIE(BLACK) A01F2UH 1EM431197
Ref. No. Description Part No. X14 ADDENDUM SHEET A17F6UH 1EMN28479
C1705 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223 IC1930# IC PHOTOCOUPLER TLP781F(D4-FUNBLL F) QPEL781FBLLF
C1706 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102 IC1931# IC PHOTOCOUPLER TLP781F(D4-FUNBLL F) QPEL781FBLLF
CN1001 FFC CONNECTOR 15P IMSA-9615S-15A-PP-A JC96J15ER007 Q1972 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
CN1003 FFC CONNECTOR IMSA-9615S-11A-PP-A JC96J11ER007 RESISTORS
CN1100# CONNECTOR/JACK 1747386-1 JB17J02AP002 R1100 RES CHIP 1608 1/10W F 39.0k Ω RTW3902HH008
CN1101# CONNECTOR/JACK 1747386-1 JB17J02AP002 R1101 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
CN1102# CONNECTOR/JACK 1747386-1 JB17J02AP002 R1102 RES CHIP 1608 1/10W F 2.20k Ω RTW2201HH008
CN1901# CONNECTOR PRINT OSU 3 S B3P4-VH-L J3VH030JG015 R1103 RES CARBON FILM T 1/4W G 470 Ω RCX4471T1002
DIODES R1104 RES CHIP 1608 1/10W F 100 Ω RTW1000HH008
D1200 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1105 RES CHIP 1608 1/10W F 13.0 Ω RTW13R0HH008
D1201 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1106 RES CARBON FILM T 1/4W G 470 Ω RCX4471T1002
D1202 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1107 RES CHIP 1608 1/10W F 100 Ω RTW1000HH008
D1203 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1108 RES CHIP 1608 1/10W F 13.0 Ω RTW13R0HH008
D1300 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26 R1109 RES CHIP 1608 1/10W F 39.0k Ω RTW3902HH008
D1301 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26 R1110 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
D1500 SWITCHING DIODE DAN202U T106 QD1Z0DAN202U R1111 RES CHIP 1608 1/10W F 2.20k Ω RTW2201HH008
D1501 SWITCHING DIODE DAN202U T106 QD1Z0DAN202U R1112 RES CHIP 1608 1/10W F 39.0k Ω RTW3902HH008
D1502 SWITCHING DIODE DAN202U T106 QD1Z0DAN202U R1113 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1114 RES CHIP 1608 1/10W F 2.20k Ω RTW2201HH008
IR SENSOR CBA
Ref. No. Description Part No.
IR SENSOR CBA ----------
Consists of the following:
CAPACITORS
C101 ELECTROLYTIC CAP. 47µF/16V M H7 CE1CMAVSL470
C103 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331
C104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
DIODE
D101 LED (WHITE) SLR343WBC7T3XM QPWM343WBC7T
RESISTORS
R101 RES CARBON FILM T 1/4W J 100 Ω RCX4101T1001
R102 RES CHIP 1608 1/10W J 3.3k Ω RRXA332HH013
R103 RES CHIP 1608 1/10W J 9.1k Ω RRXA912HH013
R106 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
MISCELLANEOUS
CL102 WIRE ASSEMBLY 5PIN 5PIN/180MM WX1A17F6-201
CL103 WIRE ASSEMBLY 4PIN 4PIN/35MM WX1A17F6-202
RS101 SENSOR REMOTE RECEIVER KSM-712TH2E USESJRSKK044
G.....±2% J......±5% K.....±10% R813 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
R815 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
M.....±20% N.....±30% Z.....+80/-20% R842 Not used
R875 Not used
R876 Not used
R879 RES CHIP 1608 1/10W J 16k Ω RRXA163HH013
Different parts from the original model R880 RES CHIP 1608 1/10W J 16k Ω RRXA163HH013
32PFL3506/F7 (Serial No. : DS1) R891 RES CHIP 1608 1/10W J 33k Ω RRXA333HH013
R892 RES CHIP 1608 1/10W J 33k Ω RRXA333HH013
R896 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
Chassis PL11.0
• 2011-03-28 32PFL3506/F7 (Serial No. : DS1) added
• 2011-08-25 32PFL3506/F7 (Serial No. : DS2) added
• 2011-11-05 32PFL3000/F8 (Serial No. : XA1) added
Note: Identical product to the 32PFL3506/F7 (Serial No.: DS1).
• 2011-11-05 32PFL3000/F8 (Serial No. : XA2) added
Note: Identical product to the 32PFL3506/F7 (Serial No.: DS2).
• 2011-11-28 32PFL3506/F7 (Serial No. : XA1) added
• TBD 32PFL3506/F7 (Serial No. : DS3) added
15-1 PL11.0REV
COMPARISON LIST OF MODEL NAME
Chassis PL11.0
32PFL3506/F7 (DS1) A17F6UH
(DS2) A17FGUH
(DS3) A17FHUH
(XA1) A17FCMA
PL11.0COM