Beruflich Dokumente
Kultur Dokumente
Issue 04
Date 2014-06-20
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the customer.
All or part of the products, services and features described in this document may not be within the purchase scope or
the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this
document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or
implied.
The information in this document is subject to change without notice. Every effort has been made in the preparation
of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this
document do not constitute a warranty of any kind, express or implied.
Website: http://www.huawei.com
Email: support@huawei.com
Contents
1 Introduction ..................................................................................................................................... 3
1.1 Appearance ....................................................................................................................................................... 4
1.2 Physical Ports ................................................................................................................................................... 4
1 Introduction
OFDM refers to orthogonal frequency division multiplexing, DSSS refers to direct sequence spread
spectrum, and CCK refers to complementary code keying.
Compliance with the IEEE 802.11 a/b/g/n standards, the LampSite solution uses two
radio frequency (RF) units to provide a maximum transmission rate of 300 Mbit/s on
each frequency band in multiple input multiple output (MIMO) 2x2 mode when OFDM
is used.
The LampSite solution works with brilliant performance and high stability. The
processor provides high throughput and robust load capability. The stable signal strength
and quality ensure reliable running of the wireless networks. Automatic power and
frequency adjustment and load balancing enable flexible and stable large-scale networks.
A rich variety of network security features are provided, such as protection against XML
denial-of-service (XDos) attacks, firewall, media access control (MAC) address filtering,
IP address filtering, and link integrity protection.
WLAN authentication and privacy infrastructure (WAPI), wired equivalent privacy (WEP), Wi-Fi
protected access (WPA), WPA2, and 802.1X are supported to ensure network security.
1.1 Appearance
A pRRU can have two Ethernet ports or three Ethernet ports. The pRRU with three Ethernet
ports can be configured with a Wi-Fi daughter board to connect to the AC and provide Wi-Fi
services. Unless otherwise specified, this document uses the pRRU with three Ethernet ports
as an example.
Figure 1-1 shows a pRRU3901 respectively.
Port Description
PoE A port connected to the RHUB. It supports the PoE and is
CPRI_E0 used to transmit CPRI data between the RHUB and the
pRRU.
The PoE emblem indicates that
the CPRI_E0 port supports the
PoE power supply.
2 Technical Specifications
Table 2-2 Modes and frequency bands supported by a pRRU3901 (SRAN9.0 or later)
Scenario Mode Frequency RX TX
Band Frequency Frequency
(MHz) Band (MHz) Band (MHz)
2.1 GHz UMTS UMTS 2100 1920 to 1980 2110 to 2170
1.8 GHz LTE LTE full band 1800 1710 to 1785 1805 to 1880
2.1 GHz UMTS + UMTS 2100 1920 to 1980 2110 to 2170
1.8 GHz LTE
LTE full band 1800 1710 to 1785 1805 to 1880
2.1 GHz UMTS + UMTS 2100 1920 to 1980 2110 to 2170
2.1 GHz LTE
LTE full band 2100 1920 to 1980 2110 to 2170
1.8 GHz GSM + 2.1 GSM 1800 1710 to 1765 1805 to 1860
GHz UMTS
UMTS 2100 1920 to 1980 2110 to 2170
2.6 GHz LTE LTE 2600 2500 to 2570 2620 to 2690
2.1 GHz UMTS + UMTS 2100 1920 to 1980 2110 to 2170
2.6 GHz LTE
LTE 2600 2500 to 2570 2620 to 2690
AWS UMTS + UMTS AWS 1710 to 1755 2110 to 2155
AWS LTE
LTE AWS 1710 to 1755 2110 to 2155
PCS UMTS + AWS UMTS PCS 1850 to 1910 1930 to 1990
LTE
LTE AWS 1710 to 1755 2110 to 2155
PCS UMTS + PCS UMTS PCS 1850 to 1910 1930 to 1990
LTE
LTE PCS 1850 to 1910 1930 to 1990
1.8 GHz LTE + 2.6 LTE full band 1800 1710 to 1785 1805 to 1880
GHz LTE
LTE 2600 2500 to 2570 2620 to 2690
2.1 GHz LTE + 2.6 LTE 2100 1920 to 1980 2110 to 2170
GHz LTE
LTE 2600 2500 to 2570 2620 to 2690
NOTE
In SRAN9.0 or later, Wi-Fi daughter boards of any frequency bands can be configured with only 1.8
GHz LTE, and 2.1 GHz UMTS+1.8 GHz LTE networks. For details about frequency bands of Wi-Fi
daughter boards, see Table 2-7.
2.2 Capacity
Table 2-3 pRRU3901 Capacity
Mode Capacity
UMTS 2 carriers
LTE 1 carrier. The bandwidth per carrier is 5, 10, 15, or 20 MHz.
The receiver sensitivity of UMTS, as recommended in 3GPP TS 25.104, is measured in the entire
operating band at the antenna connector on the condition that the channel rate is 12.2 kbit/s and the
BER is not higher than 0.001.
The receiver sensitivity of LTE is measured, as recommended in 3GPP TS 36.104, under a 5 MHz
channel bandwidth based on the FRC A1-3 in Annex A.1 (QPSK, R = 1/3, 25 RBs) standard.
NOTE
ATBR in the RX and TX Channels column indicates that this RF module has A transmit channels
and B receive channels.
C x D W in the Maximum Output Power column indicates that this RF module has C TX channels
and the maximum output power for each TX channel is D mW.
The maximum output power of the pRRU can be measured at the antenna port or calculated by using
the following formula:
Maximum output power of the pRRU = Maximum output power of the PA - Internal loss
The 11 configuration indicates that two continuous carriers are configured and the spacing between
the center frequencies of two neighboring carriers is 5 MHz. In 101 or 1001 configuration,
discontinuous carriers are configured. The value 0 indicates the spacing of 5 MHz. For example, the
1001 configuration indicates that two discontinuous carriers are configured and the spacing between
the center frequencies of the two carriers is 15 MHz.
Item Specifications
Supported 2.4 GHz frequency band: 2.4 GHz to 2.4835 GHz
frequency 5 GHz frequency band: 5.15 GHz to 5.35 GHz, 5.470 GHz to 5.725
band GHz, and 5.725 GHz to 5.850 GHz
Transmit 2 x 50 mW on each frequency band
power
Single/dual The single band and dual band are supported.
band mode
Throughput 2x2 MIMO with a maximum rate of 300 Mbit/s on each frequency
band
Item Specification
Dimensions (H x W x 230 mm x 230 mm x 50 mm
D)
Weight ≤ 3 kg
Item Specifications
Operating temperature Installed on a wall: –5ºC to +45ºC
Installed on a ceiling: –5ºC to +40ºC
Storage temperature –40ºC to +70ºC
Relative humidity 5% RH to 95% RH
Absolute humidity 1 g/m3 to 30 g/m3
Operating pressure 70 kPa to 106 kPa
Protection rate IP20
Operating environment EUROPEAN ETS 300 019-1-3 Temperature-controlled
locations Class 3.2
Storage environment ETSI EN300019-1-1 V2.1.4 (2003-04) class1.2 "Weather
protected, not temperature-controlled storage locations"
Transport environment ETSI EN300019-1-2 V2.1.4 (2003-04) class 2.3 "Public
transportation"
Anti-seismic IEC 60068-2-57 (1999-11) Environmental testing – Part 2-57:
performance Tests – Test Ff: Vibration – Time-history method
YD5083-99: Interim Provisions for Test of Anti-seismic
Performance of Telecommunications Equipment (telecom
industry standard in the People's Republic of China)
GR63 5.4.1 zone4: NEBSTM Requirements: Physical Protection
Protection from damp, Class B
mold, and salt-spray fog
Item Specifications
Absolute humidity 1 g/m3 to 30 g/m3
Operating pressure 70 kPa to 106 kPa
Protection rate IP20
Operating environment EUROPEAN ETS 300 019-1-3 Temperature-controlled
locations Class 3.2
Storage environment ETSI EN300019-1-1 V2.1.4 (2003-04) class1.2 "Weather
protected, not temperature-controlled storage locations"
Transport environment ETSI EN300019-1-2 V2.1.4 (2003-04) class 2.3 "Public
transportation"
Anti-seismic IEC 60068-2-57 (1999-11) Environmental testing – Part 2-57:
performance Tests – Test Ff: Vibration – Time-history method
YD5083-99: Interim Provisions for Test of Anti-seismic
Performance of Telecommunications Equipment (telecom
industry standard in the People's Republic of China)
GR63 5.4.1 zone4: NEBSTM Requirements: Physical Protection
Protection from damp, Class B
mold, and salt-spray fog