Sie sind auf Seite 1von 5

CURRICULUM VITAE

Name : Jaenal Abidin. ST

Status : Married

Address : Anyer Kp. Gudang Areng, Anyer Serang, Banten Indonesia

No Hp : 62 81296053378 ( Indonesia )

Place and Date of Birth : Serang,15 June 1983

Citizenship : Indonesian

Passport No : A 8087342

Email : jaenalabidin.smcc@yahoo.com

Education : Passed from University Sultan Ageng Of Tirtayasa in 2008 Cilegon

Bachelor Degree, Metalurgical Engineering

TRAINING QUALIFICATIONS:
 CSWIP 3.1 Welding Inspector Level II, Certificate No 67004
 NDT ASNT Ultrasonic Testing Level II,
 NDT ASNT Radiograhic Interpreuter Level II
 Oil and Gas Safety Passport by NIOSH 2014 Malaysia Certificate No (OG008019H)

QUALIFICATION SUMMARY
I have more than 9 years professional experience QA/QC Inspector in the project engineering
phase of Onshore/Offshore Oil & Gas, and Gas Processing Plant. Fabrication & Erection of
Piping Construction, Welding, NDT activities and Inspection & Test Plan, Quality Control
Procedure for Fabrication, Line Checking, Pressure Testing, Reinstatement and Pre-
Commissioning of various process equipments, Piping system, Equipment, etc. and coordinating
with various departments including field engineering, Planning, Fabrication and Erection. Test
Equipment Calibration Control including Heat Treatments Test, Visual Inspection, Dimensional
Check, ) Surface Preparation, also witnessed PMI Test and Pressure Test (Hydro & Pneumatic ).
WORK EXPERIENCES
November 2017
EMPLOYER : PT. BUKAKA TEHNIK UTAMA

Business Line : EPC

Period : Nov 2016 - Present

Position Held : QC Engineer

Project : Poso Energy Pamona ( Hydro Power Plant 65 x 3 MW

Description of Duties :

 Review approved technical specification, project procedures, drawings or other


documents as the reference tobe followed
 Review welding documents such as WPS/PQR, welder certificate
 Witness welder and welding operator qualification test
 Prepare ITP (Inspection and Test Plan )
 Check the drawings are clear, the issue number is marked and the latest revision is used
 Check calibration certificates, and consumer certificates are available and valid.
 Material verification as per drawing requirement.
 Ensure QA/QC Plan Implemented on field
 Monitor welding process has been qualified.
 Visual inspection and prepare weld visual inspection report.
 Review radiographic film from NDE company.
 Monitor line check, Hydro Test, Filling Test, Flushing test.

July 2014
EMPLOYER : PT. Rekind Malaysia SDN.BHD

Business Line : EPC

Period : July 2014 – October 2016

Position Held : QA/QC Piping Inspector

Client : PETRONAS CHEMICAL FERTILISER SABAH SDN BHD MALAYSIA


Description of Duties :

 Review & comment to Vendor/Sub-Contractor/Fabricator Procedure: ITP, WPS/PQR,


Welding Map, NDE Map,NDE Procedure, Fabrication Procedure, Welder Certificate, and
NDE Operator Certificate.
 Monitoring Inspection piping fabrication & verification the documents.
 Monitoring Contractor QA/QC activities at Contractor’s yard and giving guidance to the
Contractors QA/QCTeams.
 Coordinate with client, Inspection agency and authorized party due to several inspection
points.
 Material Inspection & Verification:
 Verify that incoming material is checked against material requisition specification,
applicable code and applicablespecification.
 Verify that all received material are complete with mill certificate and verified for
chemical composition,mechanical properties and test certificate as required by
specification.
 Verifying that Execution Contractors Quality Personnel are in possession of valid
qualifications related to thefunction performed
 Monitoring several Inspection activities such as: Visual & Dimension Inspection for
Material (Plate, pipe, elbow, fitting, flange, cap, reducer, bolt, tube, forging,cladding
plate) and weld production.
 Non Destructive Examination (PT, MT, UT) Witness inspection activities during
production as stated in Inspection and Test Plan (ITP)
 Witness Post Weld Heat Treatment (PWHT) if any witnessed PMI Test
 Coordinate with client, Inspection agency and authorized party due to several inspection
points.
 Monitor line check, Flushing test.
 Witness Piping Reinstatement
 Witness Hydrostatic & performance test.
 Will closely work with Fabrication Supervisor and Engineer to ensure All QA/QC related
works are completed intime with no hold-up work
Januari 2013
EMPLOYER : PT. Inwha Indonesia

Business Line : Engineering Construction

Period : Januari 2013 – September 2014

Position Held : QA/QC Coordinator

Client : 1.BP Tangguh (NCDT Project)

2.Shell Indonesia

3.Mobile Cepu Limited

Description of Duties :

 Verify that incoming material is checked against material requisition specification,


applicable code and applicablespecification.
 Witnessing all the inspection and testing activities as per the approved Inspection and
Test Plan and Inspectionsheet
 Perform welding visual inspection before weld
 Perform welding visual inspection report
 Monitoring welding activities before and during fabrication are performed as WPS
 Verify fabrication fit-up, alignment, and dimensional tolerances and Review of in related
fabrication inspectiondocument.
 Visual & Dimension Inspection for Material (Plate, pipe, elbow, fitting, flange, cap,
reducer, bolt, tube, forging)and weld production.
 Control NDE request for joint which have been visually accepted as required by NDE
plan and monitoring the status
 Witness PMI Test & Witness Post Weld Heat Treatment (PWHT).
 Monitor line check, Flushing test.
 Witness Hydrostatic & performance test. Will closely work with Fabrication Supervisor
and Engineer to ensure All QA/QC related works are completed intime with no hold-up
work.
 Perform welder test
May 2012
EMPLOYER : Sumitomo Mitsui Contruction Mitsui

Business Line : EPC contractor & engineering

Period : May 2012-Januari 2013

Position Held : QA/QC Engineer

Client : Nippon Shokubai Indonesia (i-II 2AA & SAP Plant Project Chemical Plant)

Description of Duties :

 Review original material certificates for compliance to codes and specifications and
Reporting.
 Review Project Procedures according to Client specification, Company Spec and related
code and standards.
 Review all Welding Procedure Specification (WPS) and Procedure Qualification Record
(PQR)
 Review welder qualifications certifications, and attend welder qualification.
 Monitoring and controlling the inspection activities and schedule.
 Verify fabrication fit-up, alignment, and dimensional tolerances and Review of in related
fabrication inspectionDocument
 Ensure storage and use of welding consumables is per manufacture’s recommendations
and full certification,Welding Inspection (Fit-Up, Visual Test).
 Review of inspection reports received from Inspector.
 Witnessing all the inspection and testing activities as per the approved Inspection and
Test Plan and Inspectionsheet.
 Ensure testing, measuring, welding, and NDE equipment is fully calibrated and has
current certification andAuthorized to coordinate NDT personnel to ensuring NDT
application, Review NDT Report.
 Witnessing Hydro test and PWHT if any.
 Coordinate to collect of inspection and test records (MDR).

I hereny certify that all statement in tis data is true and correct to the best of my knowledge
and belief.

Best Regard

JAENAL ABIDIN

Das könnte Ihnen auch gefallen