Beruflich Dokumente
Kultur Dokumente
R
Equipment Issue A
030-100888 Rev. B, August 2005
1. GENERAL DESCRIPTION
1.5 Product Features S Awl or drill with assorted wood or cement bits
Installation includes inspecting the kit for damages, following 1. Determine the mounted location on wall. Choose a location
proper safety precautions, gathering all the necessary tools, and with adequate lighting, unobstructed access for personnel,
mounting the kit. adequate room for proper power supply and cable access,
ventilation, equipment access, as well as sufficient horizon-
- INSPECTION NOTE - tal and vertical space left between any multiple
Visually inspect the unit for damages prior to installation. If damaged in installations. The 6060-04 should be installed in an upright
transit, immediately report the damage to the transportation company position on the wall.
and to Westell (see Part 4 for telephone number).
2. Mark the mounting hole locations to be drilled. Using the
- PRECAUTIONARY STATEMENT - bracket itself as a template, lift and place the bracket
Never install telephone wiring during a lightning storm. against the wall in the desired mounting location then mark
Never install telephone jacks in wet locations unless the jack is the exact mounting hole locations to be drilled for the
specifically designed for wet locations. mounting hardware (wall-mount hardware not included).
Never touch uninsulated telephone wires or terminals unless the Be sure to orient the bracket as shown in Figure 2, so the
telephone line has been disconnected at the network interface.
flanges that hold the power supply protrude away from the
Use caution when installing or modifying telephone lines.
wall.
ECopyright 2005 EWestell, Inc. All rights reserved. *CLEI is a trademark of Telcordia Technologies. 0508IARB
Westellr and 200 MECHANICSr are registered trademarks of Westell, Inc.
Page 1 of 2
Section 31M-K26-20A 030-100888 Rev. B R
È
email: global_support@westell.com
È
Visit the Westell World Wide Web site at http://www.Westell.com
for additional information about Westell.
È
È
4.2 Part Numbers. The enclosure is identified by a product
number (A90-31MK26), which consists of three parts: the issue let-
È
ter of the equipment (A), the assembly type (90), and the specific
model number (31MK26). Each time a product change affects the
È
ented or advanced by one. Be sure to indicate the issue level and
È
the model number when making inquiries about the equipment.
6060-04 Power Supply
È
5. WARRANTY & REPAIRS
È
5.1 Warranty. Westell warrants this product to be defect-
31MK-26 Bracket
free at shipment time and warrants this product to be fully
Noncombustible wall or backboard functional for the time period specified by the terms and condi-
tions governing the product sale. Equipment repairs or
Figure 2. Mounting the 31MK-26 modifications by unauthorized person(s) will void the warranty.
3. Drill holes. Set aside the bracket. Drill appropriately-sized 5.2 Repair and Return. Westell will repair or replace any
pilot holes (to accommodate the mounting screws or fas- defective Westell equipment without cost during the warranty
teners being used) at the marked locations before the next period if the unit is defective for any reason other than abuse, im-
step. The size of the holes and the fastening hardware varies proper use or improper installation. Before returning the
according to the wall type. Do not make the holes too large. defective equipment, first request a Return Material Authoriza-
Mounting hardware is not included. tion (RMA) number from Westell, then return the defective
unit, freight prepaid, and a brief problem description, to:
4. Fasten bracket to wall. Lift the bracket again, align the
Westell, Inc.
mounting holes on the bracket with the drilled holes in the
ATTN: R.G.M. Department
wall, and drive all screws, but do not overtighten.
750 N. Commons Drive
5. Mount 6060-04 power supply to bracket. Orient the Aurora, IL 60504-7940
6060-04 power supply in the proper direction, align the Replacements will be shipped in the fastest manner consistent
mounting holes/slots in the top and bottom of the power with the urgency of the situation. Westell will continue to repair
supply with the slots in the mounting bracket’s tabs, and se- or replace faulty equipment beyond the warranty period for a
cure with the hardware provided. nominal charge. Contact Westell for details.
- CAUTION -
Never apply power until all installer connections are made. 6. SPECIFICATIONS
To order units, call the telephone number shown in Paragraph
4.1 and please specify a specific model number shown in Table 1.
3. TESTING & TROUBLESHOOTING
The physical specifications are shown in Table 2.
This equipment should not be field repaired. If trouble is en-
countered, verify all installer and module connections, and Model Part # Description
check that the CO power fuse is not blown. If trouble persists, #
replace the suspect unit with another, optioned identically, and 31MK-26 A90-31MK26 Wall-mount bracket, for 6060-04 power
retest. If the replacement unit appears to operate correctly, the supply (KTU-type).
original unit may be faulty and should be returned to Westell for Table 1. Ordering Information
repair or replacement (Paragraph 5.2). These procedures are
not designed to effect repairs or modifications. Any tests beyond
Physical Feature U.S. Metric
those outlined herein, or repairs made beyond replacing a faulty
unit, are not recommended and may void the warranty. Height 7.2 inches 18.2 cm
Width 1.625 inches 4.13 cm
4. CUSTOMER & TECHNICAL SERVICES Depth 1.5 inches 3.8 cm
4.1 Customer Service. If technical or customer assistance Weight (approx.) 5 ounces 142 g
is required, contact Westell via one of the following options: Table 2. Physical Specifications
0508IARB
2