Beruflich Dokumente
Kultur Dokumente
ISSUE1.0
OMF000403 GSM Interference Analysis
ISSUE1.0 Table of Contents
Table of Contents
i
OMF000403 GSM Interference Analysis
ISSUE1.0 Table of Contents
ii
OMF000403 GSM Interference Analysis
ISSUE1.0 Course Description
Course Description
Introduction to Course
To introduce affection brought by interference to the GSM system, fault location
method and troubleshooting method, this course hereby lists out the possible
interference sources, and offers description of cases to facilitate fault location and
troubleshooting. The main contents of the course are as follows: overview,
classification of interference source, judgement method, location and troubleshooting,
anti-interference measures, introduction to instrument interference test, etc.
Course Objective
After completed the course, you can:
z get the cause of interference and master the method of locating the interference
source;
z Master the method of overcoming interference.
Relevant Materials
Interference Starwiarski
GSM Principle and Network Optimization Han Binjie
Mobile Communication Engineering Lu Er’Rui
1
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 1 Overview
Chapter 1 Overview
Frequency resource is a kind of rare resource. In GSM system, frequency reuse is
very necessary for GSM system to provide enough capacity. Frequency reuse means
that same frequency can be used simultaneously in several cells when the distance
between them is far enough. The distance between the cells allocating the same
frequency is called the reuse distance. And the ratio between the reuse distance and
the cell radius is called co-frequency interference factor. For certain frequency
resource, the network capacity will be larger if the frequency reuse is more tight, but
the interference will be stronger because the reuse distance becomes nearer.
The interference caused by frequency reuse is called internal network interference (it
is also called internal system interference). Besides, the GSM network may be
affected by interference from other communication systems.
Judging from the aspects such as conversation quality, call drop, handover and
congestion, it is found that interference situation is one of the most important factor
that affects the network. How to reduce or eliminate interference is now becoming
the principal task of network planning and optimization. This document herein
provides a systemic description of interference source, interference location and
troubleshooting on the basis of experience of experts.
2
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 2 Interference Sources
In the figure, Ta denotes the noise temperature, Fa denotes equivalent noise factor,
and the relation between the two is as follows:
Fa = 10 log Ta
To
Wherein, To=2900K.
3
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 2 Interference Sources
From the research data of ITT, it can be viewed that the atmosphere noise and solar
noise is comparatively low in 30~1000MHz, which can be ignored. And above
100MHz, as the radio noise of galaxy is lower than the thermal noise of typical
receiver, the interference can be ignored as well. Thus, natural noises (atmosphere
noise, galaxy noise and solar noise) are unnecessarily considered for the mobile
systems above 450MHz, 800MHz, 900MHz, 1800MHz and 2000MHz[3]. The affection
of sunspot fastigium on mobile communication is temporarily unknown, but scientists
believe that sunspot fastigium has great affection on the electric power and
communication.
According to the research of National Bureau of Standards (NBS), it is found that the
man-made noise is one of the main interference sources. Among those man-made
interference/noise sources, certain interference is uncontrollable, such as ignition
interference of vehicle engine, electric power interference and industrial electric
equipment interference. However, certain interference, such as interference between
communication equipment and internal network interference, which can be overcome
by reasonable network planning and system optimization. The latter is main research
field of this document.
Sche
matic diagram of mobile communication interference
4
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 2 Interference Sources
5
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 3 Discovery of Interference
Check the “Average TCH busy time (second)” in TCH measurement function of each
cell, the reason is that this index can show the TCH mean occupied time (s”), which is
usually called “TCH mean holding time” in the BSC of other manufacturer”, within the
measurement period. If it is found that the Average TCH busy time (second) of
certain cell is comparatively short (such as less than 10s), then maybe there is strong
interference in the cell, causing that handover/call drop happens due to bad quality
after TCH channel occupied to MS.
Certainly, if hardware fault occurs in certain TRX (non-BCCH or non-SDCCH carrier)
of a cell, the case mentioned above will also appear.
The handover measurement data reflects the mobility of the subscribers within the
cell under measurement. Generally, we can divide the handover data into two
categories for analysis, intra-cell handover and inter-cell handover.
z Inter-cell handover
There are many reasons of MS triggering handover The handover measurement
indices mainly used for judging whether there is interference are as follows: times of
attempt to initiate handover (downlink quality), times of attempt to initiate handover
(uplink quality), times of receiving quality level (0~7) when initiating handover (uplink)
and average receiving quality when initiating handover (uplink).
When certain cell initiates handover, if the average receiving quality (uplink) is ≥ 4
(this is true when there is no frequency hopping, if there is, it should be ≥5), and the
mean receiving level is ≥25(-85dBm), then it is possibly caused by uplink interference.
6
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 3 Discovery of Interference
When certain cell initiates handover, if the times of receiving quality level above 5 is
more than that below 4, then there may be uplink interference as well.
If the times of certain cell attempts to initiate handover (uplink/downlink quality) is
more than 10% of total handover attempt times, then there may be interference in the
cell. The two indices are all related to quality handover threshold and interference
handover threshold within the cell parameters.
z Intra-cell handover
For intra-cell handover, there is also measurement items such as intra-cell handover
request times (uplink/downlink quality) and the interference situation. If the intra-cell
handover is caused by uplink/downlink quality, and the proportion taken up by total
intra-cell handover times among the total inter-cell handover times is comparatively
higher than that of others, then there may be interference in the cell.
The handover measurement index is closely related to the setting of cell parameters.
The reducing of handover judgment threshold and P/N duration can make the
handover more sensitive, and cause more handovers. And on the contrary, handover
times will be reduced. Too few handover times maybe no good to the network
performance at whiles, and affect the handover success rate directly. However, too
many handover is no good either. As for the hard handover attribute of GSM,
handover is also the main cause of call drop. According to the online data
measurement, the proportion that one handover per conversation will be
comparatively reasonable.
Call drop is one of the network faults un-acceptable for the subscribers. The
measurement indices related to call drop are as follows: SDCCH/TCH call drop times,
wireless link broken times when SDCCH/TCH occupied (connection failed) and mean
uplink/downlink quality in case of SDCCH/TCH call drop.
If the call drop times of certain cell is rather higher the the other with same traffic load,
and the main cause of call drop is owning to connection fault, then it is possibly
caused by interference.
If the average receiving level during call drop is comparatively high (≥25), while the
average receiving quality level is ≥6, then the cell should be listed into the
interference source.
BTS will utilize an idle TS in a frame to scan the uplink frequencies of the frequencies
used by TRX, and then make measurement to the level 5 interference band. The
default setting of interference bands in BSC of Huawei is as follows: 110, 105, 98, 90,
87 and 85 (unit: -dBm), corresponding to the following interference bands in traffic
measurement:
7
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 3 Discovery of Interference
If the values of interference band 4 and interference band 5 are comparatively large
(≥1), then, there may be co-frequency interference in the cell. If the measurement
values mainly distribute in interference band 1 and interference band 2, then the
possibility of interference will be small. However, if there is comparatively high value
in band 3, then attention should be paid to this.
Note: As Huawei’s measurement method of interference band is based on cell, the
value of interference band of certain TRX that suffers serious co-frequency
interference will be comparatively small in large site type (S8/8/8). The reason is that
this value has been averaged by the values of other seven TRX without interference.
Thus, the values cannot reflect the actual interference condition.
8
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 3 Discovery of Interference
(FER). Generally when the FER ≥25%, subscribers can feel the discontinuous voice,
that is to say, interference exists in this section of highway (FER measurement of ANT
is inaccurate.).
9
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
The sudden deterioration of such indices as call drop rate, handover success rate,
traffic, congestion rate, interference band indicates that interference exists in the cell.
At this time, check the log of the operation on the cells is required. Check whether
BTS hardware is added or modified, and data is modified recently, or whether the
occurrence of the interference is associated with these operations in terms of time.
If no data modification is performed in this duration, it can be sure that the
interference comes from the hardware or external of the network. It is recommended
to check the hardware first, if interference still exists after the hardware fault is
excluded, then check whether external interference exists (the method for checking
external interference, please refer to the chapter infra).
Sometimes, the high call drop rate, low handover success rate and high congestion
rate may be relevant with the equipment fault, check of OMC alarm record will spare
much time spent in judgment and analysis. Similarly, the association of alarm record
with the deterioration of these indices in terms of time is analyzed here.
It should be noted that most alarms of OMC aim at the hardware fault of the such as
TRX no power output, etc. For most potential fault in optimization such as TRX or
CDU receiving performance degradation, self-excitation, etc., the alarm information
cannot be reported. (Compared with digital components, the analog components such
as microwave and so on are more difficult to detect)
If one cell is doubted with interference, check the frequency planning of this cell and
cells around. First you should be very clear about the BTS location distribution and
azimuth of each cell, then make a drawing of the topology map, and mark the
BCCH/TCH frequency and BSIC. At the same time, make a comparison between the
planned frequency and actually configured frequency in BSC to check whether there
is discrepancy.
10
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
Generally you can judge whether there is co-frequency and adjacent frequency
interference according to accurate topology map of frequency planning.
Some cell parameters have impact on the interference such as CRO, handover
threshold, handover judgment/statistics duration (P/N criteria), and adjacent cell
relation.
If CRO is set too larger than the neighbor cells, MS is drawn in this cell with in idle
mode even the actual Rx level lower than the cells around, so once C/I cannot be
more than the threshold 12dB in case of conversation, interference will emerge.
If configuration of adjacent cell is omitted in adjacent cell relation, MS will fail to
handover to the cell with better signal level and quality, this will also lead to
interference. Slight interference may also occur in case of large handover threshold,
and P/N criteria as well as handover difficulty between cells. But it is far more
dangerous if the value is too small, the frequent handover not only increases the call
drop rate, but also the system load, even leads to disastrous result, i.e., BSC
breakdown.
Drive Test is an effective way to locate the interference. The method is the same as
problem location in 3.3. The difference is that the cell with interference is highlighted
during the test when locate the interference.
Adjustments should be made respectively according to the above location results. For
details, please refer to the technical cases. Finally the effect of interference clearance
will be evaluated according to KPI, and Drive Test result.
The specific methods for interference location and clearance are described in form of
cases as follows, at the same time the case ID is provided for the convenience of
consultation.
As one of the passive devices, the possibility of antenna damage is very little, but the
real antenna damage or performance degradation will lead to poor communication
quality.
Case 0010761.
11
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
Fault description: There are 5 BTSs for a certain network in a county configured as
S4/4/4 and 6/6/6, the BTS type includes BTS20 and BTS30. The interference band 5
in TCH measurement function of some cells is over 15, and there is no alarm
information in OMC
Fault location process
1) Register the statistics task of interference band of 24 hours for the cell with
problems, it is found that interference band 5 mainly occurs in daylight, and in
the small hours near middle night, the interference band value is almost 0.
2) After opening the idle BURST of all BTSs and transmitting it in the early morning,
it is found that the interference band occurs. It disappears after transmitting is
stopped. It can be judged from this phenomenon that the interference comes
from internal network and has nothing to do with other equipment.
3) No frequency in the network and data are modified before the interference
occurs, accordingly, the interference is irrelevant with the frequency planning.
4) It can be seen from the above second and third points that the problem is
relevant with the BTS equipment.
5) Observe the RXM test interface of CDU with the spectrum analyzer in peak hour
in the daylight, it can be seen that unstable strong broadband interference and
rise of back noise occur.
6) First replace all boards (TRX, CDU, FPU, HPA, and power board) of this BTS
(BTS20, with Tower Top Amplifier) one by one, at the same time observe the
spectrum signal of RXM test interface, it can be seen that interference exists all
the time. This indicates that the interference is relevant with the antenna feeder
(including divider, combiner, feeder, antenna, lightning arrester, Tower Top
Amplifier, jumper and connector) instead of the board.
7) Since the above BTS under test has the Tower Mount Amplifier, the antenna and
feeder check is inconvenient, replace another BTS30(S4/4/4) (dual-CDU, and
dual-polarization antenna) with interference and check the antenna feeder.
8) Since no interference exists in one of the cells while strong interference exists in
another two cells in the BTS, interchange the antenna and feeder (changing the
jumper at the top of the cabinet) of the cells which are with and without
interference in the BTS in the evening. Then send idle BURST, it is found that
the interference follows the antenna and feeder. This step helps further locate
the fault which should exist in antenna and feeder system.
9) The situation remains the same even after replacing lightning arrester of antenna
feeder and checking all jumper connectors. Then it can be sure that fault exists
in the feeder or antenna.
10) Replace the jumper (i.e., antenna) at the top of the tower, it is found that the
interference follows the antenna, so the feeder fault can be excluded while the
antenna fault is quite possible. (It should be noted that the external interference
at this step cannot be excluded because the actual installation place of the
antenna does not change, but the external interference has already been
excluded in the above step. )
11) Finally check the antenna. The strong interference disappears immediately after
the antenna is replaced on the tower by using the dual-polarization antenna. For
further verification, replace the antenna of one cell with strong interference in
another BTS20 with a new one, and then the interference disappears, thus the
problem is solved here.
Sometimes the alarm cannot be reported to the OMC alarm console after the antenna
is damaged. While the antenna damage will lead to the degradation of the radiation
performance and inter-modulation. And the inter-modulation product is fed back to the
receiving channel of the BTS, generating interference and effect the conversation
quality. Similar case also includes case 0017185.
12
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
The water seepage of antenna and feeder will change the media structure and bring
high loss of radio signals. Fault cases in the on service network indicate that the
possibility for water seepage of antenna and feeder is less than that of antenna
damage, while the former often leads to the reduction of service range. And no case
that interference is caused by water seepage of antenna and feeder till now.
For case of water seepage of feeder, please refer to case 0009057.
The RF signal of GSM falls into the UHF signal, if loose contact exists in any section
from TRX, CDU, feeder to antenna will lead to high VSWR, increase of inter-
modulation and interference.
Case 0015118
Fault description: the type of certain BTS is BTS2.0,site configuration is S242, MS is
difficult to access cell 2, and also call drop often occurs during conversation. It is
found that the interference band 4 and 5 appear in cell 2 interference band of the BTS
by viewing the traffic measurement. Interference of different value occur on several
carriers of this cell through signaling tracing, but interference band only occurs to
interference band 2 and 3 several days later. Though the conversation is not affected,
the interference does not disappear. there is no alarm message in OMC system
Fault location process
1) Check carefully the frequency planning of the BTS. The possibility of internal co-
frequency and adjacent frequency interference is excluded because the BTSs in
this area are not so dense and with loose frequency reuse.
2) It is found that though interference spectrum occurs, but the interference signal
level is not too high when checking with spectrum analyzer.
3) The interference still exists after replacing carrier board, power amplification
board, power board, and CDU. Subsequently the interference occurs and
disappears along with the operations of screwing up and screwing off the
connector at the exit of CDU.
4) It is found that some scraps exist on the CDU output connector. Screw up the
connector after blowing off the scraps, and since then, interference never occurs.
This problem belongs to the soft fault. The scraps in the connector will bring
unconspicuous interference, so experience is quite important here. On the other hand,
this problem reminds us of the importance of checking the engineering quality
carefully.
It is quite usually that the antenna is connected inversely, which will lead to complete
difference between the using frequency and the planned frequency. It will also lead to
co-frequency and adjacent frequency interference, call drop, handover failure, etc. If
the frequency resources for operator is a few, antenna connected inversely will affect
the network quality much more.
Case 0011108
Fault description: the interference bands 4 and 5 often occur in the traffic
measurement after certain BTS is on service, the inter-cell handover success rate is
very low and the congestion rate is up to 5%. There is no alarm in OMC.
13
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
14
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
correct. In this case, Drive Test can be adopted for judgment. The judgment for
TX/RX feeder of one cell is easy and whether the connection is correct can be
known from the results of Drive Test. But RXD transmits no signal, it is unable to
know whether the antenna feeder is correctly connected through the Drive Test.
At this time, switch off the HPA of all carriers in the cell, and connect RXD feeder
to TX/RX output of the CDU where the main BCCH of cell is located, then switch
on the HPA for Drive Test. If correct frequency is received in the specified cell,
the connection of RXD feeder in this cell is correct, otherwise, it is incorrect.
From the Drive Test, the cell to which the RXD feeder belongs can be obtained.
Correct the connection at the lightning arrester of antenna and attach new flag
again after making a clear judgment of all feeders.
5) Verification with Drive Test is required after correction.
There are many jumpers from BTS TRX to the antenna, the confusion of which will
lead to high call drop rate. Case 0015303.
Fault description: a newly constructed BTS is of S333 type and dual-CDU
configuration with the version as 05.0529. The subscriber complains that it is difficult
to make MOC or MTC in the areas covered by this BTS since the on service. In the
traffic measurement, the SDCCH call drop rate of one cell in this BTS is up to 50%.
There is no alarm in OMC
Fault location process
1) The causes for the above phenomenon may include: interference, BSC data
error, and hardware fault. The location will focus on these 3 aspects.
2) The dial test carried out by maintenance engineer of the operator indicates that
this fault phenomenon occurs in cell 3. The “tick” always occurs in the MS and
the MS returns to the idle mode when it initiates a call, moreover, only one in four
and five times of calling is successful.
3) From the traffic measurement, it is found that SDCCH call drop rate of this cell is
very high, i.e., 50%, and moreover, all causes are radio link loss connections
(error indication). But TCH assignment is normal, so it can be judged that
SDCCH call drop is the reason why the MS is difficult to make MOCor MTC.
4) Further analysis of the traffic measurement indicates that the interference band
of this cell is normal, so the impact of interference on SD call drop can be
excluded. Considering that this BTS is a newly on service, the check should
base on data and BTS hardware.
5) A careful check of the data of this BTS including hardware data and nework
planning data shows that there is no error.
6) It is found that there are 3 carriers in 3 cells of this BTS with dual-CDU
configuration, the input of two carriers, which should be connected to the
combiner input end of CDU, is connected to TX-COMB and TX-DUP ends
instead. The fault does not exist after the connection is corrected.
As the core component of BTS, the fault of TRX will lead to the increase of
interference, decrease of coverage, access difficulty, etc.
Case 0011519
Fault description: the subscriber reports that the conversation quality in the area
near certain BTS in certain city is poor and with call drop. From the cell measurement
function report, it can be found that the average idle TCH number of interference
band 1 is 11.44 when BTS cell 2 is busy; that of interference band 2 is 32.27; that of
15
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
interference band 3 and 4 is 0 all the time; that of interference band 5 is 7.2. At the
same time it is found that the number of TCH assignment failure of this cell is up to 50,
and the call drop rate is about 10%. Since this site is on service for two years, and
running always stably . The BTS type is BTS20(M900) with the configuration of
S6/6/6, and the first 4 TRXs of each cell are connected to the “4-in-1” combiner via
rigid RF cable, while the last 2 are connected to the “2-in-1” combiner. The duplex
TMA is installed in the antenna and feeder system. No alarm information has been
generated recently.
Fault location process
1) On-site dial test and analysis of traffic measurement indicate that this is an
interference case. Generally, the number of uplink TCH, TCH congestion and
call drop rate will increase when interference exists. But further location is
necessary to determine whether it is external interference.
2) For external interference, the interference source can be located through the
signal strength within uplink band with spectrum analyzer.
3) The cause of internal interference is basically the same with that of adjacent
frequency interference. But the following will also lead to internal interference:
the performance degradation of RF devices such as antenna, Tower Mount
Amplifier, lightning arrester, combiner/divider, TRX board, and so on, as well as
the loose contact of RF cable. This problem can be solved by replacing
corresponding boards and devices.
4) The co-frequency/adjacent frequency interference can be excluded because the
frequency has already been rationally planed by the optimization engineers. The
external interference is suspected. Then carry out a test for the signal strength of
whole uplink band in the air under the tower with spectrum analyzer, and no
stable signal of more than -100dB is found. This indicates that the interference is
generated within the network.
5) Check the connection of antenna and feeder, no such antenna connected
reversely or loose contacted.
6) Then replace the duplex TMA of cell 2 with normal Tower Mount Amplifier, the
interference band has no change, it indicates that the interference is not caused
by Tower Mount Amplifier.
7) Replace related devices in cell 2 with normal SPL, combiner and RF cable, the
interference band has no change, too. So it can be sure that the interference is
not caused by the above devices. So the location focuses on the antenna and
such boards as TRX, FPU, HPA, etc. Since replacement of antenna is quite
troublesome, the board should be located first. A valuable phenomenon is found
when interference is located through blocking the baseband channel. That is,
the number of idle TCH in interference band 5 of the cell becomes 0 and the
congestion rate and call drop rate are lowered obviously after BT10, and BT11
are blocked at the same time. From this phenomenon, it can be sure that the
interference is caused by one or several boards among TRX10, TRX11, FPU10,
FPU11, HPA10, and HPA11.
8) To further locate, the FPU10, FPU11, HPA10, HPA11, TRX10, TRX11 and
corresponding boards in the cabinet of cell 3 are interchanged. Then observe the
cell performance measurement report. After TRX10, TRX11 and TRX16, TRX17
are interchanged, it is found that the interference band 5 of cell 3 becomes 5.2.
While both congestion rate and call drop rate of cell 2 become 0, number of TCH
occupation fault 1, and interference band 3, 4, and 5 0. This indicates that the
faulty board is just in TRX16, and TRX17.
9) Replace TRX16, and TRX17 respectively and observe the traffic measurement.
The traffic measurement obtained some time after TRX17 is replaced indicates
that the interference band 3, 4, and 5 of cell 3 become 0, the congestion rate and
call drop rate 0, too. It can be known that the interference is caused by self-
excitation of TRX17 internal RF circuit and performance degradation of devices.
16
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
10) No call drop occurs and the voice is distinct when performing frequency locking
dial test on each cell’s BCCH frequency.
Case 0005940
Fault description: congestion rate of 2 cells in BTS (S6/6/6)2 in certain county is
usually up to 10%. The careful view of traffic measurement (TCH measurement
function) reveals that about 7 TCHs in this cell often stay in interference band 4~5, so
the interference maybe exist.
Fault location process
1) To locate the frequency with interference, register the traffic measurement of the
cell (a period of 15 minutes) first. Block the carriers one by one. The number of
TCH in interference band 4 ~5 becomes 0 when blocking carrier 8 (frequency
28), indicating that the interference is from the frequency.
2) Connect the antenna and feeder of cell 2 with spectrum analyzer, set the central
frequency is frequency 28 (895.6MHZ). No external interference exists through
observing the level value. So the interference may come from the equipment.
3) Interchange the carrier board with interference in cell 2 with normal carrier board
in cell 3, then observe the traffic measurement. It is found that the number of idle
TCH in interference band 5 of cell 3 becomes 0, while that in cell 2 becomes 0,
too. So it can be sure that the carrier board fault leads to the interference.
4) Use Maintenance Console—GSM Interface Tracing—ABIS Interface Tracing,
and set the filtering condition to TRX management message. Then it can be
found that the radio resource indication of all timeslots in this carrier reports
interference band 5. This helps further locate that the carrier board is the
interference source.
5) The problem is solved after this faulty carrier board is replaced.
The self-excitation of carrier board or the invalidation of devices will bring strong
interference for the receiving device. So large amount of assignment fault leads to
high congestion rate of the cell.
Case 0007646
Fault description: The interference of a cell always falls into interference band 4 and
5 through the analysis of traffic measurement of certain network, and carrier 28 is
under the interference via tracing and analysis.
Fault location process
The interference source usually comes from radio communication system as following.
1) Carry out a test for the electromagnetic environment of the BTS with spectrum
analyzer. Set the start scan frequency to 895MHz and end scan frequency to
896MHz for the spectrum analyzer, then carry out the test in different time
segments. No continuous interference signal falls into this band, this indicates
that the interference maybe come from within the system and may be caused by
the fault of certain part in the equipment.
2) Replace the carrier board with interference and power amplifier board to another
cell at the same time, and register the traffic measurement of 5 minutes. The
interference disappears from original cell and occurs in new cell, indicating that
the interference may be caused by self-excitation of carrier board or power
amplifier board.
3) Mark the carrier board and power amplifier board respectively, and replace them
to the two carriers free from interference. Then register the traffic measurement
of 5 minutes for tracing and observation, it can be found that the interference
occurs to frequency where the carrier board with mark is located.
This problem is also caused by TRX self-excitation.
17
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
The clock for the digital system similar to GSM is just like the nervous system of the
equipment, so the clock unlocking of BTS will cause the BTS to “go mad”. On one
hand, the large deviation of BTS clock will bring difficulty for the MS to be locked in
the frequency of the BTS, and lead to MS handover failure or unavailability of residing
in the cell of the BTS. On the other hand, it will cause the BTS to be unable to decode
the signal correctly. It should be noted that the clock out-of-lock will not bring
interference, but the increase of error code in transmission will lead to the decrease of
voice quality.
Case 0017590
Fault description: The customer adopts transmission timeslot multiplexer to save the
transmission resource. After being used for some time, the slot multiplexer is
damaged because of the water seepage into the equipment room. After it is replaced,
all BTS 13M clocks under the combiner are out –of-lock, and interruption and
cacophony occur during conversation. The inter-BTS handover is unavailable and
call drop rate rises up. Many alarms of 13M clock out-of-clock occur in OMC alarm
console. The BTS is in free oscillation status through query of the TMU status of BTS.
Fault location process
1) Generally BTS clock out-of-lock is caused by the degradation of transmission
quality and rise of BER. The clock out-of-lock of such a large configuration BTS,
according to the former experience and the phenomenon of the problem, it is not
transmission equipment only but the sharing equipment relevant with these BTSs.
Since these BTSs are under different modules of the BSC, in addition, these
modules also support the BTS of other cities (where no clock out-of-lock is
found), so BSC clock problem can be excluded. So emphasis should be laid on
the physical link from the BSC to inter-BTS Abis interface.
2) The check of alarm box shows no transmission alarm.
3) Check the transmission of each BTS and test, The BER is not too high.
4) Check BSC clock, the clock is in normal tracing status.
5) Check of DDF shows that grounding is good and DDF combines grounding with
the BSC.
6) Disconnect the BTS under the slot multiplexer, and connect it with the BSC
directly via the jumper, skipping the slot multiplexer. It is observed that the BTS
clock changes from pull-in status to tracing status. After removing the jumper and
restoring the original connection, the BTS clock is out of lock. So the fault is
relevant with the slot multiplexer.
7) Check of the program in slot multiplexer shows that all ports are correctly defined.
8) Check of grounding of slot multiplexer shows that the power grounding is all right,
but the protection grounding is not connected. All BTS clocks can trace the
upper-level clock normally after connecting the protection grounding, so the
problem is solved..
The diversity of transmission connection from the BSC to the BTS will easily lead to
BTS fault because of the problem of certain process in the connection. Detailed
understanding of the network is quite necessary for solving the fault, and fault
phenomenon can be used to judge the possible causes. Especially the poor
grounding or contact will generate potential difference which will lead to the
degradation of transmission quality and affect the stable running of overall network.
4.2.8 Summary
The fault of any one of the TRX, CDU, feeder, antenna, jumper, and connector will
lead to interference and call drop. This is also proved by large amount of related
18
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
cases. So check and clearance of BTS hardware fault should be performed first as
interference is found. And in addition, BTS clock out-of-lock will also lead to
interference and call drop.
The hardware fault, in most cases, can be easily located and handled by exchanging
the board and analyzing the traffic measurement data. Certainly the adoption of
spectrum analyzer will help locate the problem faster. In the case that interference
occurs suddenly in some cells during the running of network data to which no data
modification is made, emphasis should be laid on the clearance of hardware fault.
The above interference related to the BTS, is mainly caused by third order
intermodulation, belongs to the uplink interference and will be directly reflected in the
interference band.
For A~D BTSs shown in the above figure, suppose that frequency N is assigned for
cell A-3, then frequency N cannot be assigned to A1, A2, B1, B2, B3, C1, C2, C3, D1,
D2, and D3; frequency N±1 cannot be assigned to A1, A2, A3, B1, C2, D1, and D2
(without frequency hopping).
The case of co-channel interference is scarce, there are only one earlier case and
one case in laboratory for reference besides the above case of co-channel
interference that the antenna is connected inversely.
19
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
Fault phenomenon: The co-channel interference of Huawei early 2.0 BTS (O2) in
certain area leads to high call drop rate and poor voice quality. Serious interruption
with occasional strong noise (whizz in general) occurs. It is after the BTS’s normal
running for a certain time that the call drop occurs. Located in a little town (Du city)
on the border of the city, the BTS is surrounded by the BTSs of the other
manufacturer.
Fault location process
1) The frequencies assigned for the BTS are 64, and 92 (64 is of BCCH frequency).
2) In the optimizing test, the receiving quality (quality level is less than 3) is
continuously good as the downlink signal level is -95dBm in the direction away
from Huanggang and Du City. In the direction from Du City to Huanggang, the
receiving quality is also good when the receiving level is more than -70dBm.
Then move forward until to the place where TA=5, the receiving quality is
sometimes good, and sometimes more than 5 in about 1 minute when the
receiving level is about -75dBm. And network-drop occurs frequently when Idle-
mode test is made at this place. It is suspected that downlink interference may
exist on BCCH frequency.
3) Carry out continuous conversation test with one test MS and scan test for 64#
frequency with another MS. The test carried out again in the section from Du City
to Huanggang reveals that the signal strength of 64# frequency is already less
than -100dBm near the Huanggang, and call drop already had occured. But the
signal strength of 64# frequency rises up to -65dBm and disappears after a
duration of 100 seconds when entering the downtown area of Huanggang. So it
can be judged that the co-channel interference may be from the TCH frequency
of cell nearby.
4) Carry out scan test for this frequency after arriving at the hotel, the signal level
still remains high, but the conversation is not implemented on this frequency. The
next day, carry out designated scan test at the place with the strongest signal of
this frequency in the street of Huanggang, and test in Idle mode with another test
MS. From the system message, it can be confirmed that 64# frequency is
assigned to the TCH in HG08 cell with BCCH frequency 45, and the
conversation is actually established once on 64# frequency in multiple times of
conversation tests.
5) The interference disappears after the application is made to the customer to
modify the frequency. At the same time, the customer should adjust the adjacent
cell relation of peer equipment.
6) Carry out test again at the place where the original co-channel interference
exists after the frequency is modified, the call drop and network drop disappear,
and conversation quality Rx_Qual<3. It indicates that the problem of co-channel
interference (downlink) is solved.
The GSM is a duplex system, so the interface may occur on both the uplink and
downlink frequencies. Current Drive Test tools are unable to measure the co-channel
interference directly, the equipment such as SAFCO, and ANT with so-called C/I test
function actually test the C/A. And in addition, the Drive Test equipment can only
measure the downlink frequency and nothing for the uplink frequency.
The co-channel interference in downlink frequency can be confirmed by using current
Drive Test equipment to measure it indirectly. First, lock the test MS in the cell of the
service area to carry out Drive Test of 2~3 hours in continuous conversation mode. If
the receiving signal in some areas is a relatively high (e.g., -85dBm) while the
receiving quality is very low (e.g., RxQual>4), it is quite possible that co-channel
interference exists in this channel.
The interference of uplink can be judged with the help of interference band statistics
data in traffic measurement
Case 0008119
20
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
Fault phenomenon: It is found in the training equipment room some day: it is hard
for the MS to access the network in BTS30 under BSC2. Even it accesses the
network narrowly, it will drop soon . Test MS shows that the signal exists
intermittently and the receiving level is very high (about -50dBm).
Fault location process
1) The correctness of the data configured by the trainees cannot be ensured in the
training equipment room. So load standard data (which is tested to ensure that
call can be connected) for BSC2, the fault still exists, so the data problem can be
excluded.
2) For the fault phenomenon, it is quite possible that fault occurs in the carrier
board. The fault still exists after replacing the TRX.
3) Check each process related to the voice for the BTS: TMU, DIP switch,
backplane cable, etc. No problem is found, so the BTS is all right.
4) Then focus is turned to the BSC. a BTS20 instead of BTS30 and change the
data into BTS20 (in this way, overall check of BSC can be performed).And the
call is set up easily , so the BSC is all right.
5) At this time, it seems that there is no way out, but restore the BTS30, however,
the MS can call again after power-on loading.
6) It seems that the problem is solved but the cause is still not located. Careful
consideration from the beginning to end reveals that all data of BSC2 and BTS30
are not modified, but BTS20 is switched off during BTS30 rollback. Think about
the phenomenon of the test MS: the signal exists intermittently and the receiving
level is very high (about -50dBm), it is possible that BTS20 works interference on
BTS30?
7) Since BTS20 is in BSC1, check the data of BSC1. It is found that the frequency
of BTS20 is set to be the same with that of BTS30. And the BSC2 data (BTS30),
configured by the trainee, is loaded in BSC1 after it is changed into BTS20,
leading to the same frequency of BTS20 and BTS30. The BTS30 is connected
with the attenuator, and the signal is far weaker than that of BTS20, so the MS
cannot access the BTS30, while can access the BTS20 . In this way, you tend to
think that it is the fault of BTS30, but the truth is hidden herein.
8) The problem is solved after the frequency of BTS30 is modified.
For the cells to which the adjacent channel cannot be allocated, please refer to the
section supra.
Case 0003451
Fault description: the customer reports that the call drop often occurs in the office
during optimization of a certain area. The traffic statistic data and Drive Test data are
normal, The BTS distribution and topology map of frequency planning are shown as
follows:
21
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
In the figure, red stands for BCCH frequencies, while black for TCH frequencies.
Fault location process
1) Thorough test reveals that the level of channel 112 is up to -73dBm in the
position of call drop. First we think the test is incorrect, but several tests indicates
that channel 112 exists from BTS A to B, and the level of which is even up to -
70dBm at some places. When the MS occupies the channel 111, call drop
occurs due to interference of channel 112.
2) Test MS indicats that channel 112 is BCCH channel in D3 cell by distinguishing
CGI.
3) Surveying in BTS D reveals that antenna of D3 cell is installed on a platform at
the top of the building, while 8m away there is one house in glass structure which
is 4m lower than the platform. Testing near the antenna. The transmitting signal
of antenna is about -26dBm, while the strength of test signal near the glass is
unexpectedly up to -14dBm. The signal by complete reflection of glass and leads
to overlap ,then cause interference and call drop.
4) It is recommended that the customer should change the installation position of
the antenna.To meet the emergency: exchange frequency 111 of BTS A with
frequency 114; increase the downtilt angle of antenna in A3 cell; adjust the
direction angle of frequency 113 in C1 cell to avoid the interference of frequency
114 after the exchange.
5) The test is all right after the modification. Frequency 113 of BTS C will work no
interference for frequency 114, and the call drop disappears.
Case 0004034
Fault phenomenon: The call drop ratio is universally high and even up to about 15%
in busy hour after several BTSs are cut over. And it is difficult for the call to be set up
during on-site test. There is no alarm message in OMC system
Fault location process
22
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
1) All BTSs are connected to the same BSC, and call drop occurs after cutover of
new BTSs.
2) The transmission quality is good, and TRX test is carried out for the above BTS
with call drop and this indicates that each TRX is all right. No fault is found by
checking the data and carrying out the test for 32BIE port corresponding to the
BTSs. From the above analysis, the TRX fault, BSC hardware fault, A interface
circuit fault and transmission fault can be excluded.
3) Analysis of traffic measurement result reveals that serious interference occurs in
each cell of the above several BTS. Most cells have measurement values in
interference band 4 and 5, and the number of channels falling into interference
band 5 in several cells is up to 7. So it is sure that the interference in the above
several cells is quite serious.
4) It is found that there are many adjacent channels and the frequency planning is
irrational after checking the frequency configuration of above BTSs and the
adjacent cells. Especially, the area where the above BTSs are located, is newly
added, and interference exists among them. And they also have interference in
between them and the surrounding running BTSs.
5) Call drop disappears after adjusting and loading the frequency configuration of
this area.
The objective of one rationally designed network is that each cell only covers the area
around the BTS and the MS resides in the nearest cell. The over-coverage is that the
service range of a certain cell is too wide that the signal level at an interval of more
than 1 BTS is still strong to let the MS reselect or hand over to it. It is a phenomenon
in which the actual cell service range deviates from the designed service range,
leading to irrational traffic loading, interference, call drop, congestion, hand over
failure, etc.
Case 0005164
Fault phenomenon: The hand over success rate of a certain GSM network is low,
the call drop rate is high and conversation quality is poor. The hand over success
rate is less than 80%, and the call drop rate is more than 2%. It is found that there are
many times of downlink/uplink strength hand overs through view and analysis of
traffic measurement data. while there are many times of bad downlink quality, and
uplink strength among the times of unsuccessful handover. The analysis of cause of
call drop indicates that the times of bad downlink quality are more than those of bad
uplink quality . There is no alarm message in OMC system
Fault location process
1) From the result of traffic measurement, it can be judged that downlink
interference may exist in the system or the coverage is not very good.
2) The actual result of Drive Test shows that the strength of outdoor signal can be
up to -80dBm above in the downtown area, that is to say, the coverage is all right.
But serious over-coverage exists. For example, the service cell used in the
building where BTS A is located is cell B with the same BCCH frequency as cell
A1, while cell B is 6 kilometers away from BTS A in the suburb. In this way, the
problem exists in two aspects: 1. The signal of cell B forms co-channel
interference which leads to poor downlink link quality in coverage area of cell 1 of
BTS A. It is found that ”****” is displayed in the test MS when this cell is locked
during the test. 2. When cell B is selected as the service cell, its adjacent cell is
only geographically adjacent to it, while the cell near the BTS A does not function
as its adjacent cell. So when its signal is unavailable, the “effect of isolated
island” will occur because the signal of its adjacent cell is poor, too. Then hand
over fault and even call drop will easily occur. The on-site survey shows that the
23
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
antenna of cell B is hung 50m above. The data provided by the customer reveals
that the tilt angle is 5°, which is actually far less than 5°.
3) The cause for bad network indices lies in over-coverage, so the basic way is
adopted to lower the antenna and adjust downtilt of it to make actual coverage
area consistent with planned coverage area. Temporarily this problem can only
be solved by adjusting the network parameter. The following operations can be
adopted: lower the power level of cell B and add the adjacent cell of cell B, at the
same time increase the level threshold of candidate cell from 10 to 15. The
network indices exhibit obvious improvement after the above check and
modification are performed for all cells in the downtown area, moreover, the
hand over success ratio rises up to 85%, while call drop ratio drops to 1.3%.
The capacity and quality are a pair of contradictions. In the downtown area, there are
large number of subscribers, so the frequency planning technology of tight reuse
should be adopted to satisfy the requirement of capacity. That is, the increase of
capacity is traded by the sacrifice of quality.
The adoption of tight reuse in the place where the layout of some BTSs is irrational
will easily lead to collision of co-channel or adjacent channel.
Case 0017397
Fault phenomenon: The interference of frequency hopping is serious and the
conversation is intermittent on a bridge, this network adopts the mode of 1*3
frequency hopping. There is no alarm.
Fault location process
1) The signals on the bridge are disorderly due to distribution of multiple BTSs
around the river. So the interference of frequency hopping will easily occur when
adopting frequency hopping.
2) First, adjust the antenna to make one main cell on the bridge, adjust the antenna
and transmission power of other cells to reduce the strength of their signals
reaching the bridge. Then carry out the test. It is found that though the
interference is reduced, yet the interference of frequency hopping still cannot be
under control because all signal receiving levels reaching the bridge are very
high due to the clearance around the bridge. Finally modify the frequency plan,
and adopt the frequency hopping plan of A+B, i.e., adopt 1*3 frequency hopping
for some cells, while 1*1 frequency hopping for other cells. The interference of
1*3 frequency hopping occurs in co-directional cell, while 1*1 frequency hopping
averages the interference. A combination of them in some local areas is better
for the dispersion of interference. The actual test result indicates that the
conversation quality is improved significantly.
24
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
the network indices conform to requirement before the complaint. Both BSC and MSC
are devices of Huawei and two BTSs are connected in star mode. The traffic
measurement indices show that traffic of both BTSs decreases obviously after
occurrence of this problem, especially in the first and third cells. Although the signal of
channel is very strong, the quality of voice is poor. Then it can be seen from traffic
measurement that the interference band of these four cells is in class three, four, and
five, and 95% of channels are under interference. In addition, interference of different
classes also exists in other cells. So subscribers complained strongly. And there is
no alarm message in OMC system
Fault location process
1) The feedback of subscribers shows the possible causes as follows: 1. Problem
occurs in transmission and leads to error code; 2. Problem occurs in antenna
feeder; 3. Fault exists in TMU; 4. Internal or external interference may exist.
2) The traffic measurement console shows the possible reasons as follows: 1.
There may exist strong uplink interference signal in the north lean to west in this
area. This leads to interference of different levels in the first, second and third
cells, especially in the first and third cells;
3) It is found that it is difficult to put through the call in the first and third cells
through on-site dial test. Although the call is put through, the quality of voice is
very poor, and the voice is intermittent seriously with strong interference. If MS
subscriber calls fixed telephone subscriber in this area, it is hard for fixed
telephone subscriber to hear the voice clearly, instead, MS subscriber can hear
fixed telephone subscriber clearly. This also proves the above analysis that the
interference may be external (It can be judged from this point that interference
only exists in uplink.)
4) Carry out test on site with antenna feeder analyzer. No problem of BTS itself is
found, and the situation remains the same after TMU is replaced. Therefore, we
ask customers whether there are such newly constructed equipment as
microwave station, repeater, etc. surrounding the BTS. They told that they didn’t
set up them. It is said that China Mobile sets up a repeater in the area, which is
located about two kilometers away in the north lean to the west of both BTSs of
Huawei, and when it is activated, the problem will occur in Huawei BTS. Then
customers negotiated with China Mobile several times. Finally China Mobile
carried out on-site test with Huawei engineers together, and found that only if the
repeater is switched off, the interference band and call become normal along
with the recovery of Huawei BTS, if the repeater is activated, problem will occur
soon in Huawei BTS, i.e. call cannot be put through, or interference is strong
even after call is put through. The traffic measurement relevant with interference
band in two different cases was handed on to China Mobile, and they approved
our viewpoint. Finally the problem is solved with the coordination of China Mobile.
Case 0001084
Fault phenomenon: it is found that call drop rate in the second and third cell of a
certain BTS (S2/2/2) in traffic measurement increases abruptly. Call drop rate is up to
about 20% at some time.
25
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
Case 0000279
Fault phenomenon: the quality of MS call is very poor in the morning of the third
day (Monday) after a BTS cutover, and it is hard to make calls 2 km away from the
BTS. The voice is under a serious interference, and the complaint of subscriber
increases obviously. Interference band is found large in traffic measurement of OMC.
Fault location process
1) When Drive Test is carried out around the BTS, it is found that MS’s RX signal
level (downlink level) has little change (about –60dBm), but the signal quality RQ
has too much change, it will jump from 0 to 7 and call drop occurs.
2) The fault remains the same after the TRX corresponding to the frequency is
replaced. It is suspected that fault is caused by external interference.
z Measurement for external electromagnetic environment with HP8595E spectrum
analyzer shows that strong interference exists around the frequency of BTS.
Through communicating with customer and the Radio Resource Management
Committee, we get known that the interference is caused by signals transmitted
by one message transmitter of some company, whose RF band is just adjacent
26
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
to the planned GSM frequency. This transmitter usually transmits every Monday,
and no such phenomenon is found in two days after BTS is activated.
27
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
measurement also shows that there is no interference. Use Site master to test
antenna feeder system. The Standing Wave Radio is normal. BTS earth is good.
From the above analysis, it is sure that the problem has nothing to do with this
BTS.
2) Make detailed dial test in B city (22 BTS totalled downtown) and C city (10 BTS
in total in downtown) and find that some BTSs have the same fault phenomenon.
Analyze the commonness of each failed BTS and find that these BTS are all
under BM4. Make sure whether all BTS under BM4 have this case. Choose other
BTSs under BM4 to make dial test and find every BTS has this problem. All
BTSs under other five BM modules have no this case through dial test. The
problem of metal chink is related to BM4 through above location, and the
problem exists in one certain process of BM4 “voice signal transmission path”.
3) Transmission path of voice signal: MS—— radio link (including antenna feeder
system)—— BTS—(E1 line)— BTS_DDF—— trunk transmission——
BSC_DDF—(E1 line)—32BIE—(HW line)—GNET——GOPT—(optic fiber)—
GFBI——GCTN——E3M—(E1 line or transmission device)—MSM——FTC——
MSC.
4) Adopt locating method of analizing section by section. At first analyze and see
whether there is something wrong with swithing network board (GNET and
GCTN) and fiber interface circuit: check the connection and connector between
AM and BM4. They are normal. Use absolute alcohol to clean the fiber connector,
but the fault remains the same. Exchange the third and fourth FBIs (including
FBC) corresponding to BM3 and BM4 with the first and second FBI board
corresponding to BM1 and BM2, but the fault remains the same. Change BM4
GOPT, but the fault remains the same. The possibility of existence of circuit error
code in the part “OPT—(fiber) —FBI” can be excluded. Swap BM4 GNET board,
the problem still exists; swap GCTN board, the problem is still; exchange GNET
board with BM3, the problem is still; exchange E3M board with BM3, the problem
is still.
5) The same fault exists in all BTS under the whole BM4. Error code should not
exist on HW Lines between 32BIE and NET board. That is because it is
impossible that all HW Lines between 32BIE and GNET board are not good.
6) Check the connection line of BM4 from E3M to MSM carefully, and find that the
connector of E3M is normal; check one connector of MSM and find that the
quality of the connector of trunk lines behind one MSM (board No. is 3) is bad.
Deformation and invagination occur on the inner pin of one connector. The
result is that the connector cannot connect the connector of MSM board on
backplane well. The cause lies in here. When the subscriber occupied TCSM
under BM4 sound of metal may occur. The number of MSM of the failed TCSM is
3, and the number of FTC is 84, 85, 86, 87. A interface circuit CIC is 2336~2463.
7) Redo the trunk connector, the fault is eliminated. During the conversation under
all BM4 there is no sound of metal.
When MSC assigns circuit, the circuits in the module that the signaling link belongs to
will be selected with higher priority. If the signaling of the MS call is transmitted
through module 4 of MSC, MSC will assign the circuit of module 4 first (the
corresponding CIC is from 2240 to 2815). The failed circuit (CIC is from 2336 to 2463)
corresponds to module 4 of MSC. So if the signaling of call is transmitted through
module 4 of MSC, the rate for being assigned to the failed circuit is very high. As for
BSC, BTS of module 4 selects A interface link first to transmit signaling. There are
three links on module 4 of BSC, Two of which correspond to module 4 of MSC. So if
the MS is used under module 4 BTS, there is a possibility of 2/3 to be assigned to the
circuit of MSC module 4. 128 of MSC module 4 circuits has fault (corresponding to
BSC 4 module) (the proportion of failed circuit of MSC module 4 is 128/576) and it
may bring about problems of voice quality. The highest rate of occurrence of fault (all
have fault when 128 circuits is busy) is about 2/3 * 128/576 = 15 %. In fact the fault of
dial test under BTS is 10 % or so.
28
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 4 Location and Clearance of Interference Source
29
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 5 Anti-interference Measures
30
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 6 Interference Test Tools
31
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 7 Way to Test Interference
32
OMF000403 GSM Interference Analysis
ISSUE1.0 Chapter 7 Way to Test Interference
33