Beruflich Dokumente
Kultur Dokumente
Karachi: Room No.1, Mezzanine Floor, Al-Hayat Chambers, A-7, Block-7/8, K.C.H.S. Tel: +92 21 4535898-99, Fax: +92 21 4558071
Lahore: 25-A, FCC, Syed Maratib Ali Road, Gulberg 4, Tel: +92 42 5763360 Fax: +92 42 5875384
The curing reaction will not proceed at area very well during application and
Metals - abecote 384 low temperature. drying. Avoid naked flames in the
Porous surfaces – abecote 386 If surfaces are not at least 2° C above vicinity.
MIXING the dew point, there is every chance Avoid inhalation of dust and contact
that a film of condensed moisture may with skin and eyes. Suitable protective
Stir the contents of each container, be present. This will upset adhesion of clothing, gloves, eye protection and
particularly the base, very well. Add the coating. respiratory protective equipment
activator to base and stir together for Wet film thickness should not exceed should be worn. The use of barrier
at least five minutes using a flat the recommended figures as solvent creams provides additional skin
paddle. It has been found that entrapment could result. The same protection. If contact with skin occurs,
mechanical mixing gives better condition may be caused if overcoating wash with water and soap. Splashes
dispersion than manual mixing. A times are shortened. Solvent into eyes should be washed
suitable mixing method would be a entrapment in the film can lead to poor immediately with plenty of clean water
slow-speed electric drill (approximately performance. and medical advice sought.
200 r/min) fitted with a paddle.
If only part of a kit is to be used, add CLEANING Cured abecote 320 is inert and
one volume of activator to two volumes harmless.
of base. Measuring must be accurate abe Super brush cleaner before
and separate stirrers and containers setting. NB: When transporting by aircraft, ask
used for proportioning each for material safety data sheet.
component. PROTECTION ON COMPLETION
The mixed material must be left to IMPORTANT NOTE
stand in a cool place for 20 minutes Protect the surface against traffic and
prior to application. spillage until cured. This data sheet is issued as a guide to
Most epoxies chalk and degrade in the use of the product(s) concerned.
Beware high summer temperature and extensive sunlight. Whilst abe Construction Chemicals
overfast mixing causing extremely fast endeavours to ensure that any advice,
curing. Very low winter temperatures TEMPERATURE & HUMIDITY recommendation, specification or
retard/stop curing. information is accurate and correct, the
company cannot - because abe has no
Do not apply if humidity is in excess of
COVERAGE 85%, or if the surface is less than 2º C
direct or continuous control over where
and how abe products are applied -
above dew point.
Recommended av. accept any liability either directly or
dft per coat 36 µm indirectly arising from the use of abe
2
MODEL SPECIFICATION products, whether or not in accordance
12,5 m / l on with any advice, specification,
Theoretical coverage smooth Two-component solvent borne recommendation, or information given
for above dft surfaces epoxy enamel coating. by the company.
(glass)
Wet film thickness at The coating will be abecote 320, FURTHER INFORMATION
above 8 µm a two-component solvent-borne epoxy
enamel coating applied in accordance Where other products are to be used
2
Practical coverage 8 m / l / coat with abe Construction Chemicals' in conjunction with this material, the
for estimating (depending on recommendations, including necessary relevant technical data sheets should
purposes surface primers as directed. be consulted to determine total
texture) requirements. abe Construction
2 coats for
PACKAGING Chemicals has a wealth of technical
Recommended and practical experience built up over
number of coats optimum
abecote 320 is supplied in 5l yield years in the company’s pursuit of
appearance
metal containers. excellence in flooring and concrete
technology.
For wet film thickness of 80 microns: HANDLING & STORAGE
2
12,5 m / l on glassy surfaces.
2
8 m / l on porous surfaces. All abecote 320 related products have
a shelf life of 12 months if kept in a
APPLICATION dry, cool store in the original,
unopened packs.
abecote 320 may be applied by brush, If stored at high temperatures and/or
short-fiber roller or airless spray. high humidity conditions, the shelf life
Spraying would be through a tip of may be reduced.
approximately 250 µm.
Stir frequently during use. HEALTH & SAFETY
abecote 320 should not be applied if
the ambient temperature is below 10° C Wet abecote 320 is toxic and
flammable. Always ventilate a working
Revision 9203
Karachi: Room No.1, Mezzanine Floor, Al-Hayat Chambers, A-7, Block-7/8, K.C.H.S. Tel: +92 21 4535898-99, Fax: +92 21 4558071
Lahore: 25-A, FCC, Syed Maratib Ali Road, Gulberg 4, Tel: +92 42 5763360 Fax: +92 42 5875384