Sie sind auf Seite 1von 4

MasterSeal® 940 (Formerly known as Masterflex Waterbars )

Flexible PVC Waterstops

DESCRIPTION OF PRODUCT PACKAGING


MasterSeal 940 are PVC waterstops used for
the sealing expansion, contraction and C15 30 Linear metres per roll
C20 30 Linear metres per roll
construction joints. Various types of MasterSeal
C20 T 30 Linear metres per roll
940 are available in different sizes depending on C20 M 30 Linear metres per roll
their intended use. C24 30 Linear metres per roll
C24 T 30 Linear metres per roll
PRIMARY USES C24 M 30 Linear metres per roll
C32 15 Linear metres per roll
MasterSeal 940 are specially designed for water E20 15 Linear metres per roll
retaining and water excluding structures, for it E24 15 Linear metres per roll
prevents the passage of water through E32 15 Liner meters per roll
expansion, contraction and construction joints in
the following applications:- STANDARDS & TECHNICAL PROPERTIES:
 Primary and secondary containment facilities
 Dams, locks, canals, water reservoirs and Type: Polyvinyl Chloride
aqueducts Service temperature: -35°C to + 55°C
 Sewage plants Welding temperature: 160 -180°C
 Water treatment plants Shore A Hardness: >80
 Culverts and tunnels (ASTM D2240)
 Storage tanks Tensile strength: >14N/mm²
(ASTM D638)
 Retaining walls
Elongation at break: >300%
 Bridge and deck abutments (ASTM D638)
 Foundation Alkali resistance: Weight change (+)
 Slab on grade (CRD – C572-65) 0.0631%
 Roof slabs Hardness Change (-) 3.2
 Parking garages points
Accelerated Extraction: Tensile strength
ADVANTAGES (CRD – C572-65) 16.9N/mm²
 Wide range of sizes to suit all construction Elongation 302%
requirements Stiffness in flexural 4.42 Mpa
strenght (CRD C 571)
 Quick and easy-tie to the rebar
 Labor-saving features
Tear Resistance 58.93 N/mm
 Speeds installation (ASTM D624
 Stays in place during concrete placement
 Cost effective Low Temperature No crack observed
Brittleness (-30°) C570

Water Absorption: 0.036%


(ASTM D570)
Volatile loss: 0.73%
(ASTM D1203)
MasterSeal® 940 (Formerly known as Masterflex Waterbars )

DIMENSIONS: MasterSeal 940 feature great inherent elasticity


and abrasion resistance. MasteSeal 940 is
suitable for above or below-grade construction.
Width in cm Roll Length Thickness
Type Width in cm Thickness (±10%)
(±1%)
C15 15 3
C15 T 15 1
C20 20 4
C20 T 20 1
C20 M 20 3
C24 24 4.5
C24 T 24 1
C24 M 24 3
C32 32 5
E20 20 5
E24 24 8
E24 M 24 5.5
E32 32 6 MasterSeal 940 profiles must be installed using
clips so they are securely held in the correct
DESIGN position whilst the concrete is poured. The
concrete must be fully and properly compacted
PVC waterstop were originally designed as
around the waterstops (the use of BASF’s
simple dumbbell profiles which worked on the
Rheodynamic admixtures to produce self
valve sealing action of the opening joint putting
compacting concrete is of great advantage to
the waterstop in tension, thus sealing the water
avoid voids or porous areas after concrete
path. Later designs included multi ribs and fins, in
placing). Where reinforcement is present, an
what is knows as the tortuous path principal of an
adequate clearance must be left between this
extended potential water track created by the ribs
and all Waterstops to permit proper compaction
and fins.
of the concrete.
MasterSeal 940 combine all the accepted and
proven principles of PVC waterstop in four valve
and tortuous path design and grout check fins on
all construction / contraction joint profiles.
150mm

INSTALLATION PROCEDURE code Web Roll Length LM


In concrete structures, Waterbars must be Thickness
designed to seal the expansion, contraction and mm
construction joints and to accommodate lateral C 15 3 30
and transversal movements that could cause the C 15T 1 30
joint to open, close and misalign. MaserSeal 940
should also be designed to accommodate the
expected hydrostatic head within the structure
and must be compatible with concrete forming
200mm
methods and rebar placement design.
MasterSeal 940 are made from virgin raw code Web Roll Length LM
materials and are unaffected by the normal range Thickness
of concrete or concrete additives. mm
MasterSeal 940 will not discolour concrete and C 20 3.5 30
do not produce electrolytic action with adjacent C 20T 1 30
metal structures or reinforcing bars.
Resistant to many water-borne chemicals,
MasterSeal® 940 (Formerly known as Masterflex Waterbars )
governed by slab all thickness, position of

240mm
code Web Roll Length LM
Thickness
mm
C 24 4.5 30
C 24M 3 30
C 24T 1 30 reinforcing steel and aggregate size. As a
general rule, the 250mm width profiles are
appropriate for slab/ wall thickness over 250mm,
allowing good compaction and width of barrier to
water penetration.
200m
code Bulb Web Roll For concrete members less than 250 mm the use
Diameter Thickness Length LM of a smaller profile approximating to the actual
mm slab or wall thickness will be appropriate.
E 20 13mm 4 15
19mm
CHEMICAL RESISTANCE
PERMENANT RESISTANCE TO:
 Sea water
 Salt solutions
240mm  Potable and sewage water
code Bulb Web Roll
Diameter Thickness Length LM TEMPORARY RESISTANCE TO:
mm
 Alkalis
E 24 17mm 8 15
25mm  Mineral oils
E 24M 5.5 15  Mineral acids

SELECTION CONSIDERATIONS STORAGE


MasterSeal 940 is designed for use within the Store under cover, out of direct sunlight and
performance parameters indicated under the protect from extremes of temperature. For
headings Technical Data and Typical Properties. specific storage and disposal instructions, please
Centrally placed profiles are usually located contact BASF’s Technical Services Department.
midway in the slab or wall thickness across the
joints in concrete structures. They will equally STANDARDS
prevent the passage of water through the joint MaserSeal 940 has been tested in accordance to
from either face. They are particularly suited to ASTM D638/ASTM D412 and found to be
water retaining structures and in walls and slabs complying with CRD-C 572-6
where pressure differential may occur such as in
reservoir walls. They are equally appropriate for
joints in suspended slabs, vertical wall joints and
lift joints. The choice of width of profile is mainly
MasterSeal® 940 (Formerly known as Masterflex Waterbars )

NOTE
Field service, where provided, does not
constitute supervisory responsibility. For
additional information, contact your local BASF
representative.

BASF reserves the right to have the true cause of


any difficulty determined by accepted test
methods.

QUALITY STATEMENT
All products manufactured by BASF Egypt, or
imported from BASF affiliate companies world-
wide, are manufactured to procedures certified to
conform to the quality, environment, health &
safety management systems described in the
ISO 9001:2008, ISO 14001:2004 & OHSAS
18001:2007 standards.

* Properties listed are based on laboratory controlled tests.


® = Registered trademark of the BASF-Group in many countries

BASF_CC-EG/Seal_940_09_10/v1/06_14

Das könnte Ihnen auch gefallen