Sie sind auf Seite 1von 5

THE FASTEST WAY TO JOIN HDPE PIPE —

NO IFS, ANDS, OR BUTTS.


The Refuse-to-Fuse™ System for HDPE Pipe The Refuse-to-Fuse™ System for HDPE Pipe

STRONG
DESIGNED FOR
BURIED OR HDPE joints completed per hour on 4" SDR 11 HDPE pipe
ABOVE GROUND
APPLICATIONS Electrofusion 1.3

AS STEEL
Flanging 2.5

Butt Fusion 6
Mechanical
Coupling 20

“WITH THIS COUPLING, IT’S SO EASY... JUST MARK THE DEPTH,


SLIDE THE PIPE IN AND TIGHTEN IT UP... MUCH FASTER THAN FUSING.”
Dave, Stone Hill Contracting
HOUSING

BOLT/NUT INSTALLS UP TO 10× FASTER


Join HDPE pipe in half the time it takes to fuse a joint. Forget the fusion
equipment. Gone are the days of waiting for plastic to heat up just to
cool down. Installing in tight or vertical spaces has never been easier;
STAINLESS the Refuse-to-Fuse system goes where no fusion machine has gone before.
STEEL TEETH
That's time savings you've never seen before.

LUBE

GASKET INSTALLATION IS WEATHER INDEPENDENT PUSH


STAINLESS Whether it's rain, shine, or just downright frigid and fierce, Refuse-to-Fuse
STEEL TEETH products can be installed. No need to check the weather forecast and worry
about protection for fusion equipment or project delays any longer.

REFUSE-TO-FUSE PIPE JOINING TECHNOLOGY MEETS OR EXCEEDS PRESSURE RATINGS OF HDPE PIPE JOIN
If you thought your fused joint was tough, check out Refuse-to-Fuse product
How does it work?
performance. Small diameter solutions call for dual rows of razor-sharp teeth
Small diameter that sink into the O.D. of HDPE pipe, forming a sealed hold that never lets go.
Dual rows of stainless steel teeth Bringing out the big guns? Large diameter solutions enlist a rugged double
engage into the outside diameter groove to seal the deal. Push it, pull it, and drag it to the max; treat it the
of plain end HDPE as coupling same way you would treat fused pipe.
housing halves are tightened bolt
pad to bolt pad, allowing for visual
confirmation of correct assembly. INSTALLS WITH SIMPLE TOOLS TIGHTEN
Large diameter No need to set up your fancy fusion machine because all you will need
with the Refuse-to-Fuse system is a simple socket wrench. If you want
Coupling “keys” engage into double to get crazy, a cordless impact driver will do the job, too!
grooved HDPE pipe as coupling
housing halves are tightened bolt Don’t worry about training certificates or learning how to use fusion
pad to bolt pad, allowing for visual equipment, just stick with the basics.
confirmation of correct assembly.

PB-234 REV F refuse-to-fuse.com 1 PB-234 REV F


Pressure rating of all Refuse-to-Fuse™ products meet Pressure rating of all Refuse-to-Fuse™ products meet
The Refuse-to-Fuse™ System for HDPE Pipe or exceed the performance capabilities of the pipe The Refuse-to-Fuse™ System for HDPE Pipe or exceed the performance capabilities of the pipe

-
Plain End Installation-Ready™ Installation-Ready™ Refuse-to-Fuse™

N
Y™ IO

Y™ IO
AD LAT

AD LAT
RE AL

RE AL
ST
Refuse-to-Fuse™ Coupling for Flange Adapter for HDPE-to-

ST
IN

IN
HDPE Pipe Flanged Pipe
STYLE 905 STYLE 904

Download publication 19.07 for complete information Download publication 19.12 for complete information

• Designed for plain end HDPE pipe from DR7 – DR17 • Designed to provide a single transition from
plain end HDPE pipe (DR7 – DR17) to flanged
• Sizes from 2 – 8" IPS and 63 – 225 mm ISO
piping system components
• Sizes from 3 – 8" IPS HDPE to 3 – 8" IPS ANSI
Class 150 Flange
Certifications/Listings:

WaterMark

Download publication 10.01 for complete information


-

Refuse-to-Fuse™ Coupling for Refuse-to-Fuse™ Fittings


N
Y™ IO
AD LAT
RE AL

HDPE-to-Steel Pipe for HDPE Pipe


ST
IN

STYLE 907
Download publication 19.11 for complete information
Download publication 19.10 for complete information • Available in DR7, DR11, and DR17
• Designed to provide a single transition from plain end • Sizes from 2 – 8" IPS and 63 – 225 mm ISO
HDPE pipe from DR7 – DR17 to grooved steel sized
piping system components • Full flow fittings

• Sizes from 2 – 8" IPS HDPE to 2 – 8" IPS grooved steel • Compatible for use with Style 905 and 907
HDPE couplings
• Sizes from 63 – 225 mm ISO HDPE to 2 – 8" 
ISO grooved steel
Certifications/Listings: Certifications/Listings:

WaterMark WaterMark
No. H10 No. H11 No. H20 No. H50
Download publication 10.01 for complete information Download publication 10.01 for complete information
90° Elbow 45° Elbow Tee Reducer

Refuse-to-Fuse™ Coupling for Mechanical-T Spigot Outlet


Double-Grooved HDPE Pipe STYLE 926
STYLE 908
Download publication 11.07 for complete information
Download publication 19.09 for complete information • Designed to provide an outlet connection
on HDPE, steel, and ductile iron pipe materials
• Designed for double grooved HDPE from DR7 – DR17 in IPS, ISO, and AWWA pipe sizes
• Sizes from 8 – 36" IPS and 250 – 900 mm ISO • 4" outlets available for 10 – 32" IPS pipe diameters
• Standard Victaulic coupling assembly procedure • 114.3 mm outlets available for 250 – 800 mm
used for installation ISO pipe diameters
• 6" outlets available for 16 – 48" IPS pipe diameters
• 168.3 mm outlets available for 450 – 1000 mm
Certifications/Listings: Larger diameter couplings
ISO pipe diameters
have lifting lugs for easy
maneuvering around
the job site.

Download publication 10.01 for complete information

2 PB-234 REV F refuse-to-fuse.com 3 PB-234 REV F


The Refuse-to-Fuse™ System for HDPE Pipe The Refuse-to-Fuse™ System for HDPE Pipe

CASE STUDY
ATLAS RESOURCES HAMMAN
PROJECT
Type of Facility:
Salt Water Disposal
Victaulic Solutions:

SALT WATER DISPOSAL Construction Piping Services


Ease and Speed of Installation
Installation Time Savings
Prefabrication
In June 2015, construction was completed at the Atlas Resources Owner:
Hamman salt water disposal (SWD) facility in Jacksboro, Texas. Atlas Resources

The Hamman facility is comprised of ten water tanks, two oil Contractor:

tanks, one gun barrel, and three offload stations. Prior to its Black Sheep

commencement, the project’s contractor knew the job would be Engineer/Consultant:

laden with challenges associated with joining HDPE pipe while Atlas Resources

facing construction schedule constraints.


Fusing HDPE pipe would be an unfavorable option because During the first week of assembly, the job site was hit with
it of its extremely time-consuming nature. Additionally, high winds and 11 – 13" | 28 – 33 cm of rain. Fortunately,
fusion would require good weather conditions in order thanks to Victaulic, construction was able to remain on
to allow for proper mending of fusion welds. schedule, with the prefabricated portion finishing in 6 days
and the offload station and additional piping finishing in
Prefabrication options and new Victaulic HDPE products
10 days. The easy-to-install Victaulic HDPE couplings
boasted several attractive benefits, including controlled
were the ideal solution to deal with heavy rain and wet
costs and a dramatic improvement on the SWD facility’s
conditions, especially when compared with HDPE fusion.
completion date. Victaulic was able to provide a hard
number for the prefabrication piece of the project and After successfully overcoming various challenges by
presented the new Style 908, Style 907, and Style 905 using Victaulic HDPE solutions, the Hamman facility was
HDPE couplings as a way to finish the job in just recognized by the Plastic Pipe Institute (PPI) and received
3 – 4 weeks, according to Atlas Resources personnel. the 2016 Energy Piping Systems Division Project of the
Year award.

SPECIFICATIONS
Services: Pipe Materials: Pipe Size Range:
Gun Barrell Piping SDR 9 HDPE 10" IPS
Offload Station SDR 9 HDPE 4  –  6" IPS
Tank Manifold Piping SDR 9 HDPE 8  –  10" IPS
Oil Carbon Steel 2 – 4" | DN50–DN100

4 PB-234 REV F refuse-to-fuse.com 5 PB-234 REV F


North and South America Europe, Middle East, Africa and India Asia Pacific
UNITED STATES AND BELGIUM CHINA
WORLD HEADQUARTERS EUROPE HEADQUARTERS Unit 808, Building B
4901 Kesslersville Road Prijkelstraat 36 Hongwell International Plaza
Easton, PA 18040 USA 9810 Nazareth, Belgium No.1602 West Zhongshan Road
1 800 PICK VIC 32 9 381 15 00 Shanghai, China 200235
1 800 742 5842 49 6151 9573 0 86 21 6021 9400
(within North America) (within Germany) vicap@victaulic.com
1 610 559 3300
viceuro@victaulic.com
pickvic@victaulic.com KOREA
UNITED KINGDOM 4F, Seoil Building, 1430-5,
CANADA Seocho-Dong, Seocho-Gu
Units B1 & B2, SG1 Industrial Park
123 Newkirk Road Cockerell Close, Gunnels Wood Road Seoul, Korea 137-070
Richmond Hill Stevenage, Hertfordshire, UK 82 2 521 7235
Ontario L4C 3G5 Canada SG 1 2NB vicap@victaulic.com
1 905 884 7444 44 1438 310 690
viccanada@victaulic.com viceuro@victaulic.com TAIWAN
No. 55, NanGong Rd, LuZhu District
MEXICO UNITED ARAB EMIRATES TaoYuan City 338, Taiwan
Calle Circuito del Marqués P.O. Box 17683, Unit XB 8 886 3 222 3220
No 8 al 11 Jebel Ali Free Zone vicap@victaulic.com
Parque Industrial El Marqués Dubai, United Arab Emirates
Municipio El Marqués AUSTRALIA AND
971 4 883 88 70
Queretaro, Mexico NEW ZEALAND
CP 76246 viceuro@victaulic.com
7 Chambers Road
52 442 253 0066 INDIA Unit 1
vical@victaulic.com Altona North, Victoria
India Land Global Industrial Park
Australia 3025
Plot 4, Hinjewadi, Phase-1, Mulshi
BRAZIL 1 300 PIC VIC
Pune 411057, India
Av. Marquês de São Vicente 1 300 742 842
91 20 67 919 300
446 Cj 1303 (within Australia)
Várzea da Barra Funda – viceuro@victaulic.com
0 508 PICK VIC
São Paulo-SP 0 508 7425 842
CEP 01139-000 – Brazil (within New Zealand)
55 11 3548 4280 61 3 9392 4000
vicbr@victaulic.com vicaust@victaulic.com

For additional locations, information and


support, visit www.victaulic.com/contactus

refuse-to-fuse.com

PB-234 3188 REV F 02/2017


Victaulic and all other Victaulic marks are the trademarks or registered trademarks of Victaulic Company, and/or
its affiliated entities, in the U.S. and/or other countries. All other trademarks listed herein are the property of their
respective holders, in the U.S. and/or other countries. The terms “Patented” or “Patent Pending” refer to design or
utility patents or patent applications for articles and/or methods of use in the United States and/or other countries.
© 2017 VICTAULIC COMPANY. ALL RIGHTS RESERVED.

Das könnte Ihnen auch gefallen