Beruflich Dokumente
Kultur Dokumente
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
10701-P-LI-009-A
Page 2 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
GENERAL REQUIREMENTS
SUMMARY OF CHANGES
Revision Changes
0 As indicated
NUG7NH0 valve added
B As indicated
Manual Valves data sheet
A First Issue
Page 3 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
This specification covers material and technical requirements for pipes, fittings, flanges and other components used for process and
utility system covered by ASME B31.3.
2 REFERENCE DOCUMENTS
The reference documents listed below form an integral part of this General Specification. Unless otherwise stipulated,
the applicable version of these documents, including relevant appendices and supplements, is the latest revision published at
the EFFECTIVE DATE of the CONTRACT.
ASME B1.1 Unified Inch Screw Threads (UN and UNR Thread Form)
ASME B1.20.1 Pipe Threads, General Purpose (Inch)
ASME B16.5 Pipe Flanges and Flanged
ASME B16.9 Factory-Made Wrought Steel Buttwelding Fittings
ASME B16.11 Forged Fittings, Socket-Welding and Threaded
ASME B16.20 Metallic Gaskets for Pipe Flanges Ring-Joint, Spiral Wound, and Jacketed
ASME B16.21 Nonmetallic Flat Gaskets for Pipe Flanges
ASME B16.25 Buttwelding Ends
ASME B16.36 Orifice Flanges
ASME B16.48 Line Blanks
ASME B18.2.1 Square and Hex Bolts and Screws (Inch Series)
ASME B18.2.2 Square and Hex Nuts (Inch Series)
ASME B36.10M Welded and Seamless Wrought Steel Pipe
ASME B36.19M Stainless Steel Pipe
ASTM Standard
Annual Book
API STD 594 Check Valves: Flanged, Lug Wafer and butt-Welding
API STD 598 Valve Inspection and Testing
API STD 600 Bolted Bonnet Steel Gate Valves for Petroleum and Natural Gas Industries
API STD 602 Compact Carbon Steel Gate Valves – Flanged, Threaded, Welding and Extended Body Ends
API STD 607 Fire Test for Quarter-turn Valves and Valves Equipped with Nonmetallic Seats
API STD 609 Lug- and Wafer-Type Butterfly Valves
Page 4 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
MSS SP-6 Standard Finishes for Contact Faces of Pipe Flanges and Connecting-End Flanges of Valves and Fittings
MSS SP-25 Standard Marking System for Valves, Fittings, Flanges, and Unions
MSS SP-55 Quality Standard for Steel Castings and Forgings for Valves, Flanges and Fittings, and Other Piping
Components – Visual Method for Evaluation of Surface Irregularities
MSS SP-95 Swaged Nipples and Bull Plugs
MSS SP-97 Integrally Reinforced Forged Branch Outlet Fittings, Socket Welding, Threaded, and Buttwelding Ends
Reference documents
SCP-00-PD-03 Piping material specification (Minmetal)
PEXGOL CATALOG: sistema de tuberías para uso de infraestructura e industria.
ESPEC TEC. ET-03: Especificación técnica para la fabricación de cañerías de PRFV con resina poliestar y
vinilester.
3. GENERAL REQUIREMENTS
Pipe diameters
Design limits
Pipe wall thickness values that are specified in the piping material specifications are adequate for the full range of
pressure/temperature combinations tabulated.
Pipe wall thickness shall be determined according to ASME B31.3 Code, and shall include corrosion allowance and mill
undertolerance.
Corrosion allowance
Mill Tolerance
The mill tolerance on wall thickness shall be according to each material standard specification.
Page 5 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
GENERAL REQUIREMENTS
4. DESIGN REQUIREMENTS
Flanges
Flanges up to 24" shall be dimension according to ASME B16.5., if requiered, 26 in. and above shall be according to ASME
B16.47 Serie A.
Gaskets
Bolts
For use as a bolt thread lubricant and as a protective coating for bolted joints exposed to atmospheric attack,
use Never Seez NSBT-9 compound or equal nickel-based lubricant
Special Parts
General notes:
TECHNICAL SPECIFICATION
LINE CLASS SELECTION
SUMMARY
Rx
ITEM CLASS SERVICE CODE BASE MAT. ENDS Design Limits Notes
%
AC1 (Compressed air) / AC2 (Compressed air) ASME Carbon 175 psig / -20°F to 100°F
2 A1C 150 # - RF
/ WF2 (Fire water) / WU1 (Process water) B31.3 Steel 125 psig / 353°F
ST1 (Steam low pressure) / SC1 (Steam ASME Carbon 175 psig / -20°F to 100°F
3 A1C1 150 # - RF
condensate) B31.3 Steel 125 psig / 353°F
ASME Galvanized
4 A1E PW4 (Seal water) 150 # - RF 175 psig / 32°F to 150°F
B31.3 CS
ASME
5 B1A BR4 (Brine wells) PVC 150 # - RF 100 psig / 73°F
B31.3
ASME
6 E1A IA2 (Air instrument) SS 304 150 # - RF 150 psig / 200°F
B31.3
ASME
7 H1A WO1 (Water RO) SS 316L 150 # - RF 150 psig / -17°F to 300°F
B31.3
CR1 (Repulp Slurry) / BR3 (Lithium carbonate - ASME Alloy 400 230 psig / -20°F to 100°F
8 M1A 150 # - RF
Reactor) B31.3 (Monel) 180 psig / 400°F
BR2 (Brine liquids / Lithium 1,8 % WT / Lithium 150 psig / -15°F to 75°F
9 L2C NFPA HDPE 150 # - RF 0
chloride liquor) 80 psig / 140°F
DIN
HA2 (Hydrochloridic acid 30% and above) /
11 P2C-B HA3 (Hydrochloridic acid 8-20%)
16965 PRFV 150 # - FF 150 psig / 32°F to 149°F
Part IV
TECHNICAL SPECIFICATION
FLANGED SEAMLESS PIPE ASTM A106 Gr. B 40 ASME B36.10 RF 1" - 24" (1)(2)(3)
FLANGED FITTINGS ASTM A216 Gr. WCB 150# ASME B16.5 RF 1" - 24" (1)(8)
BLIND FLANGE ASTM A105 N 150# ASME B16.5 BLIND RF 1" - 24" (1)
STUD BOLTS ASTM A193 Gr. B7, Zincplated ASME B18.2.1 (10)
NUTS ASTM A194 Gr. 2H, Zincplated ASME B18.2.2
SPECTACLE BLIND 1" - 12"
ASTM A105 150# ASME B16.48 RF (1)(13)
PADDLE & SPACER BLIND 14" - 24"
Notes:
1.- Cross Linked Poliethylenne linned (Pex) according to ASTM D1998-04, tested according to ASTM D638.
- Minimun specified tensile strenght 23 N/mm².
- Minimum elongation 300%.
2.- Lenght shall me accordin to design requierements.
3.- Flanges shall be ASTM A105N ASME B16.5 RF Welding neck.
4.- Maximum face to face lenght of flanged spool shall be 6m.
5.- In case of Flanged Joints, special caution should be taken when torquing. Torque values shall be provided by the linner manufacturer. It is
prohibited the use of other torque values.
8.- Schedule according to Manufacturer STD.
10.- Lenght according to ASME B16.5 (Except for PSV, orifice plate, drip ring, wafer type valves.)
11.- If requiered, Gasket shall be RF according to ASME B16.21, Expanded PTFE material.
12.- Linned carbon steel will be provided by Golan plastic products (PEXGOL)
13.- PTFE linned alternative also suitable
Page 8 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
24" T
20" T R
18" T R R
16" T R R R
14" T R R R H
BRANCH SIZE
12" T R R R H H
10" T R R R H H H
8" T R R R H H H H
6" T R R R H H H H H
4" T R R R H H H H H H
3" T R R R H H H H H H H
2" T R R R H H H H H H H H
1½" T R R R H H H H H H H H H
1" T R R H H H H H H H H H H H
¾" T R R R H H H H H H H H H H H
½" T R R R R H H H H H H H H H H H
½" ¾" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24"
HEADER SIZE
REFERENCES:
Notes:
1.- This table gives the minimun requierement for the 90° branch connection in sizes shown.
Page 9 of 66
10704-P-ET-006
Rev: 0
TECHNICAL SPECIFICATION
TECHNICAL SPECIFICATION
SERVICE: AC1 (Compressed air) / AC2 (Compressed air) / WF2 (Fire water) / WU1 (Process water)
STUD BOLTS ASTM A193 Gr. B7, Zincplated ASME B18.2.1 (10)
NUTS ASTM A194 Gr. 2H, Zincplated ASME B18.2.2
SPECTACLE BLIND 1" - 12"
ASTM A105 150# ASME B16.48 FF
PADDLE & SPACER BLIND 14" - 24"
O-LET FITTINGS ASTM A105 MSS SP-97 NPT ½" - 24" (4)
SWAGE NIPPLE ASTM A105 MSS SP-95 BW-NPT ½" - 4" (4)(8)
BRANCH REINFORCEMENT ASTM A516 Gr. 70 ASME B31.3 16" - 24"
Notes:
TECHNICAL SPECIFICATION
SERVICE: AC1 (Compressed air) / AC2 (Compressed air) / WF2 (Fire water) / WU1 (Process water)
24" T
20" T R
18" T R R
16" T R R P
14" T R R P P
BRANCH SIZE
12" T R R P P P
10" T R R P P P P
8" T R R N P P P P
6" T R R W W W W W W
4" T R R W W W W W W W
3" T R R W W W W W W W W
2" T R R W W W W W W W W W
1½" T H H H H H H H H H H H H
1" T R H H H H H H H H H H H H
¾" T R R H H H H H H H H H H H H
½" T R R R H H H H H H H H H H H H
½" ¾" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24"
HEADER SIZE
REFERENCES:
T Straight TEE.
R Reducing TEE
N Stub-ins, no reinforcing pad requiered.
P Stub-ins with reinforcing pad according to ASME B31.3 Paragraph 304.3 if required. (4)
H Threadolet.
W Weldolet
Notes:
1.- This table gives the minimun requierement for the 90° branch connection in sizes shown.
2.- For lateral branch connections between 45° and 90°, the reinforcement need shall be calculated according to ASME B31.3.
3.- This table covers the reinforcement requierements of branch connections subjected only to pressure. Special considerations shall
be taken to a branch connection subjected to external loads due to thermal expansion or contraction, dead and live loads.
4.- 100% reinforcement shall be provided when a reinforcing pad is requiered according to ASME B31.3
5.- Use same material and thickness as the header pipe for the reinforcement pad unless otherwise specified on piping class.
Page 12 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
GASKETS RING type, PTFE Gore e=3 mm 150# ASME B16.21 ½" - 24"
STUD BOLTS ASTM A193 Gr. B7, Zincplated ASME B18.2.1 (10)
NUTS ASTM A194 Gr. 2H, Zincplated ASME B18.2.2
SPECTACLE BLIND 1" - 12"
ASTM A105 150# ASME B16.48 RF
PADDLE & SPACER BLIND 14" - 24"
O-LET FITTINGS ASTM A105 MSS SP-97 SW ½" - 24" (4)
SWAGE NIPPLE ASTM A105 MSS SP-95 BW-PE ½" - 4" (4)(8)
BRANCH REINFORCEMENT ASTM A516 Gr. 70 ASME B31.3 16" - 24"
Notes:
TECHNICAL SPECIFICATION
24" T
20" T R
18" T R R
16" T R R P
14" T R R P P
BRANCH SIZE
12" T R R P P P
10" T R R P P P P
8" T R R N P P P P
6" T R R W W W W W W
4" T R R W W W W W W W
3" T R R W W W W W W W W
2" T R R W W W W W W W W W
1½" T H H H H H H H H H H H H
1" T R H H H H H H H H H H H H
¾" T R R H H H H H H H H H H H H
½" T R R R H H H H H H H H H H H H
½" ¾" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24"
HEADER SIZE
REFERENCES:
T Straight TEE.
R Reducing TEE
N Stub-ins, no reinforcing pad requiered.
P Stub-ins with reinforcing pad according to ASME B31.3 Paragraph 304.3 if required. (4)
H Sockolet
W Weldolet
Notes:
1.- This table gives the minimun requierement for the 90° branch connection in sizes shown.
2.- For lateral branch connections between 45° and 90°, the reinforcement need shall be calculated according to ASME B31.3.
3.- This table covers the reinforcement requierements of branch connections subjected only to pressure. Special considerations shall
be taken to a branch connection subjected to external loads due to thermal expansion or contraction, dead and live loads.
4.- 100% reinforcement shall be provided when a reinforcing pad is requiered according to ASME B31.3
5.- Use same material and thickness as the header pipe for the reinforcement pad unless otherwise specified on piping class.
Page 14 of 66
10704-P-ET-006
Rev: 0
TECHNICAL SPECIFICATION
TECHNICAL SPECIFICATION
80 ½" - 1½"
SEAMLESS PIPE ASTM A106 Gr. B Galv. ASME B36.10 THRD
40 2" - 4"
SEAMLESS PIPE (NIPPLE) ASTM A106 Gr.B Galv. 80 ASME B36.10 THRD ½" - 1½"
FORGED FITTINGS ASTM A105 Galv. 3000# ASME B16.11 THRD ½" - 4"
FLANGES ASTM A105 Galv. 150# ASME B16.5 THRD / RF ½" - 4" (1)
BLIND FLANGE ASTM A105 Galv. 150# ASME B16.5 BLIND RF ½" - 4"
GASKETS RING type, PTFE e=3 mm 150# ASME B16.21 ½" - 4"
STUD BOLTS ASTM A193 Gr. B7, Zincplated ASME B18.2.1 (10)
NUTS ASTM A194 Gr. 2H, Zincplated ASME B18.2.2
SWAGE NIPPLE ASTM A105 Galv. MSS SP-95 THRD ½" - 4" (1)
Notes:
TECHNICAL SPECIFICATION
24"
20"
18"
16"
14"
BRANCH SIZE
12"
10"
8"
6"
4" T
3" T R
2" T R R
1½" T R R R
1" T R R R R
¾" T R R R R R
½" T R R R R R R
½" ¾" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24"
HEADER SIZE
REFERENCES:
T Straight TEE.
R Reducing TEE.
Notes:
1.- For instrument vent and drain connections on headers, use swagges with straigh tee of header size
Page 17 of 66
10704-P-ET-006
Rev: 0
TECHNICAL SPECIFICATION
TECHNICAL SPECIFICATION
½" - 12"
GASKETS PTFE Gore e=3 mm 150# ASME B16.21 (12)
14" - 24"
STUD BOLTS ASTM A193 Gr. B7, Zincplated ASME B18.2.1 (2) (3)
NUTS ASTM A194 Gr. 2H, Zincplated ASME B18.2.2 (4)
SPECTACLE BLIND ASTM A516 Gr.70, PTFE RF ½" - 12"
150# ASME B16.48
PADDLE & SPACER BLIND Linned FF 14" - 24"
Notes:
1.- PVC piping must be installed with extreme care. All joints must be carefully made according to pipe manufacturer´s instructions. Piping must
be adequately supported to prevent excessive flexing, vibration and joint failures.
2.- Lenght according to ASME B16.5 (Except for PSV, orifice plate, drip ring, wafer type valves.
3.- All bolting to be applied with aluminum, copper and graphite grease. (Permatex Anti-seize lubricant type)
4.- Bolting shall be provided with 2 (two) flat washers.
5.- All socketwelds to be made with heavyduty industrial grade solvent cement (ASTM D2564) for specified manufacturer PVC pipe materials.
Procedure for making solvent cemented jontis shall be according to ASTM D2855.
6.- Transition joints between PVC and any other material shall be ASME Flanged.
7.- Branch connections shall be made with tees and reducing tees.
8.- Branch, vent drain and pressure instrument connections shall be made with reducing tees and bushings.
9.- Hydrostatic vent connections shall be made using threaded couplings and bushings with PVC plugs.
10.- Hydrostatic drain connections shall be valved and blinded, 1/2 in minimun size.
11.- All bolting shall be done with a torque wrench. Boltes shall be weel lubricated and pulled down gradually to a uniform tightness as listed
below.
12.- Gasket type according to Flange Facing.
TECHNICAL SPECIFICATION
73
TEMPERATURE ºF FLANGE CLASS: 150
DESIGN PRESSURE psig 100 MATERIAL: PVC underground
CODE: B 31.3
CA: 0mm
24" T
20" T R
18" T R R
16" T R R R
14" T R R R R
BRANCH SIZE
12" T R R R R R
10" T R R R R R R
8" T R R R R R R R
6" T R R R R R R R R
4" T R R R R R R R R R
3" T R R R R R R R R R R
2" T R R R R R R R R R R R
1½" T R R R R R R R R R R R R
1" T R R R R R R R R R R R R R
¾" T R R R R R R R R R R R R R R
½" T R R R R R R R R R R R R R R R
½" ¾" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24"
HEADER SIZE
REFERENCES:
T Straight TEE.
R Reducing TEE or TEE+RED or TEE+Reducing bushing.
Notes:
Page 20 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
GASKETS RING type, PTFE e=3 mm 150# ASME B16.21 ½" - 24"
Notes:
TECHNICAL SPECIFICATION
24" T
20" T R
18" T R R
16" T R R P
14" T R R P P
BRANCH SIZE
12" T R R P P P
10" T R R P P P P
8" T R R N P P P P
6" T R R W W W W W W
4" T R R W W W W W W W
3" T R R W W W W W W W W
2" T R R W W W W W W W W W
1½" T H H H H H H H H H H H H
1" T R H H H H H H H H H H H H
¾" T R R H H H H H H H H H H H H
½" T R R R H H H H H H H H H H H H
½" ¾" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24"
HEADER SIZE
REFERENCES:
T Straight TEE.
R Reducing TEE
N Stub-ins, no reinforcing pad requiered.
P Stub-ins with reinforcing pad according to ASME B31.3 Paragraph 304.3 if required. (4)
H Sockolet
W Weldolet
Notes:
1.- This table gives the minimun requierement for the 90° branch connection in sizes shown.
2.- For lateral branch connections between 45° and 90°, the reinforcement need shall be calculated according to ASME B31.3.
3.- This table covers the reinforcement requierements of branch connections subjected only to pressure. Special considerations shall
be taken to a branch connection subjected to external loads due to thermal expansion or contraction, dead and live loads.
4.- 100% reinforcement shall be provided when a reinforcing pad is requiered according to ASME B31.3
5.- Use same material and thickness as the header pipe for the reinforcement pad unless otherwise specified on piping class.
Page 22 of 66
10704-P-ET-006
Rev: 0
TECHNICAL SPECIFICATION
TECHNICAL SPECIFICATION
GASKETS RING type, PTFE e=3 mm 150# ASME B16.21 ½" - 24"
Notes:
TECHNICAL SPECIFICATION
24" T
20" T R
18" T R R
16" T R R P
14" T R R P P
BRANCH SIZE
12" T R R P P P
10" T R R P P P P
8" T R R W W W W W
6" T R R W W W W W W
4" T R R W W W W W W W
3" T R R W W W W W W W W
2" T R R W W W W W W W W W
1½" T H H H H H H H H H H H H
1" T R H H H H H H H H H H H H
¾" T R R H H H H H H H H H H H H
½" T R R R H H H H H H H H H H H H
½" ¾" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24"
HEADER SIZE
REFERENCES:
T Straight TEE.
R Reducing TEE
P Stub-ins with reinforcing pad according to ASME B31.3 Paragraph 304.3 if required. (4)
H Sockolet
W Weldolet
Notes:
1.- This table gives the minimun requierement for the 90° branch connection in sizes shown.
2.- For lateral branch connections between 45° and 90°, the reinforcement need shall be calculated according to ASME B31.3.
3.- This table covers the reinforcement requierements of branch connections subjected only to pressure. Special considerations shall
be taken to a branch connection subjected to external loads due to thermal expansion or contraction, dead and live loads.
4.- 100% reinforcement shall be provided when a reinforcing pad is requiered according to ASME B31.3
5.- Use same material and thickness as the header pipe for the reinforcement pad unless otherwise specified on piping class.
Page 25 of 66
10704-P-ET-006
Rev: 0
TECHNICAL SPECIFICATION
TECHNICAL SPECIFICATION
Notes:
TECHNICAL SPECIFICATION
24"
20"
18"
16"
14"
BRANCH SIZE
12" T
10" T R
8" T R R
6" T R R W
4" T R R W W
3" T R R W W W
2" T R R W W W W
1½" T H H H H H H H
1" T R H H H H H H H
¾" T R R H H H H H H H
½" T R R R H H H H H H H
½" ¾" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24"
HEADER SIZE
REFERENCES:
T Straight TEE.
R Reducing TEE
H Sockolet
W Weldolet
Notes:
1.- This table gives the minimun requierement for the 90° branch connection in sizes shown.
2.- For lateral branch connections between 45° and 90°, the reinforcement need shall be calculated according to ASME B31.3.
3.- This table covers the reinforcement requierements of branch connections subjected only to pressure. Special considerations shall
be taken to a branch connection subjected to external loads due to thermal expansion or contraction, dead and live loads.
Page 28 of 66
10704-P-ET-006
Rev: 0
TECHNICAL SPECIFICATION
TECHNICAL SPECIFICATION
SCH /
DESCRIPTION MATERIAL DIM. CODE ENDS SIZE NOTES
RATING
BLIND FLANGE ASTM A536 Gr. 60/40/18 PFA Lined 150# ASME B16.42 BLIND RF 1" - 12"
Notes:
68.- Bolt torque requirements shall be in accordance with gasket manufacturer’s recommendation.
72.- All components may not be available from all manufacturers in size ranges shown
87.- All HPDE pipe and pipe components shall be manufactured and supplied through a single (same) manufacturer
88.- HPDE materials shall not be used in hydrocarbon-contaminated (2% concentration or greater) soil
89.- HPDE shall be provided with long-term UV protection (2% to 3% carbon black)
90.- The effects of surge pressure on the system shall be reviewed for design velocities greater than 5 feet/second
91.- Butterfly valves may require HPDE spacers on each side of valve to permit disc rotation
92.- Flange adapters shall be provided with a serrated sealing surface
93.- One edge of the back-up ring shall be radiused or chamfered. This edge shall fit against the back of the flange adapter.
97.- If used, buried metallic components shall be protected from corrosion by coating, cathodic protection, or other acceptable means.
98.- All fittings molded or fabricated shall meet full pressure rating (FM Class 150). Fiberglas reinforcement (covered) of HPDE fittings shall not be
permitted.
115.- Integral wire electrofusion couplings shall be installed in accordance with manufacturer’s instructions. Use shall be limited to closure joints in
which butt fusion is not feasible.
126.- Stainless steel flat washers shall be used between the nut and back-up ring in accordance with manufacturer’s recommendations.
142.- Carbon steel lap joint flanges shall be acceptable for use in systems for which FM approval is based on use of carbon steel lap joint flanges.
a.- If Gaskets are requiered, 1/8" thick Neoprene, full face, 55 – 75 Durometer, Shore “A” shall be used.
b.- Piping Class according to PIP: PN12PD0H01. Sent by MdA as a part of "Division 15-MECHANICAL 15001 Piping and accesories".
c.- Bolt Torque in flanged connections shall be indicated by the HDPE Supplier.
Page 30 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
12" T
10" T Z
8" T Z R
BRANCH SIZE
6" T Z R R
4" T Z Q Q Q
3" T Z Q Q Q Q
2" T R R Q Q Q Q
1½" T R R R Q Q Q Q
1" T R R R R Q Q Q Q
¾" T R R R R R Q Q Q Q
½" T R R R R R R Q Q Q Q
½" ¾" 1" 1½" 2" 3" 4" 6" 8" 10" 12"
HEADER SIZE
REFERENCES:
T Normal TEE
R Reducing TEE / Branch Saddle or TEE w/Butt Welding Reducer.
Q TEE w/Butt Weld Reducer.
Z TEE w/Butt Weld Reducer or Branch Saddle Reducing TEE
Notes:
1.- This table gives the minimun requierement for the 90° branch connection in sizes shown.
Page 31 of 66
10704-P-ET-006
Rev: 0
TECHNICAL SPECIFICATION
TECHNICAL SPECIFICATION
SERVICE: BR2 (Brine liquids / Lithium 1,8 % WT / Lithium chloride liquor) / BR6 (Hot LiCl brine 30% and above,LOW Ca/Mg Brine, Rinse
water/brine, barium chloride trated brine, neutralized regenerant, low boron Ca/Mg Brine, Rinse water/spent regenerant, Rinse waste,
Lithuim 6% WT / ML2 (Mother liquor carbonate) / VT2 (Vent from tanks)
PIPE GRP, Vinilester Resin PE, Butt and wrap jointing system 1" - 16" (1)(7)
FITTINGS GRP, Vinilester Resin PE, Butt and wrap jointing system 1" - 16" (1)(2)(5)(7)
FF ASME B16.5, PE Butt and wrap
FLANGES Integral GRP, Vinilester Resin 1" - 16" (6)(9)(10)
jointing system
BLIND FLANGE GRP, Vinilester Resin FF, ASME B16.5 1" - 16" (6)(10)(13)
Notes:
1.- Manufacturer to specify wall thickness suitable for pressure class and recommended ASTM D2996/ASTM D2310 Designation code. Outside
diameter, inside diameter and thickness shall be provided by the pipe manufacturer for review and approval. Wall thickness shall include:
a) Internal 3 mm thickness corrosion barrier of 2 layers of Nexus Veil Material (35 kg/m²) 90-95% of weight in resin. Corrosion barrier resin
shall be Type-A Bisphenol Epoxy Vinyl Ester Resin (Derakane 411; Hetron 922; Palatal 430 or equal). Resin Manufacturer shall submit
a resin recommendation verification/letter that the inner linner/corrosion barrier resin is suitable for service in the specified fluid and
pressure/temperature design conditions. The corrosion barrier reinforcement shall be Type-E Fiberglass MAT 450 gr/m² 60-65% of
weight in resin, to complete the linner thickness requirement.
b) Structural reinforcement shall be Filament Winding type with Type-E 2000Tex (2000 gr/m²) Fiberglass Continuos Roving with 30-35%
of weight in resin. Thickness shall be according to pressure/temperature design conditions.
c) External barrier shall have a synthetic or Fiberglass Veil for Corrosion protection, Identification and UV protection purposes.
2.- }
Structural reinforcement shall include Type-E Fiberglass MAT 450 gr/m² interlaying Bidirectional Ronving Veils according to:
a) 220 gr/m² for fittings up to 4 in., 50-60% of weight in Resin.
b) 600 gr/m² for fittings above to 4 in., 50-60% of weight in Resin.
3.- No additional material filler is permitted for GRP pipes, fittings and flanges. (e.g.: sand or recycled material).
4.- Visual examination shall be according to ASTM D2563-94 (Standard Practice for Classifying Visual Defects in Glass-Reinforced Plastic
Laminate Parts).
5.- Fittings shall be manufactured using Hand Lay-up Method and the recommendations of NBS-PS-15/69.
6.- Flanges shall be according to ASME B16.5 Class 150. When manufacturing special caution should be taken to avoid tears and material
delamination.
7.- Jointing system shall be according to DIN 16966 Part VIII, UHDE 303014, AFNOR-NFT 57900 and particular practices for Highly corrosive
chemicals. The use of fillers (others than those indicated) for bevels sealing is not permitted. Jointing shall be 100% wrapped. Beveled ends
shall be 18° or less to permitt the aplication of veils and fiberglass.
Page 33 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
SERVICE: BR2 (Brine liquids / Lithium 1,8 % WT / Lithium chloride liquor) / BR6 (Hot LiCl brine 30% and above,LOW Ca/Mg Brine, Rinse
water/brine, barium chloride trated brine, neutralized regenerant, low boron Ca/Mg Brine, Rinse water/spent regenerant, Rinse waste,
Lithuim 6% WT / ML2 (Mother liquor carbonate) / VT2 (Vent from tanks)
TECHNICAL SPECIFICATION
32 to 178
TEMPERATURE ºF FLANGE CLASS: 150
DESIGN PRESSURE psig 150 MATERIAL: PRVF
CODE: DIN 16965 Part IV
CA: 0 mm
SERVICE: BR2 (Brine liquids / Lithium 1,8 % WT / Lithium chloride liquor) / BR6 (Hot LiCl brine 30% and above,LOW Ca/Mg Brine,
Rinse water/brine, barium chloride trated brine, neutralized regenerant, low boron Ca/Mg Brine, Rinse water/spent
regenerant, Rinse waste, Lithuim 6% WT / ML2 (Mother liquor carbonate) / VT2 (Vent from tanks)
24"
20"
18"
16" T
BRANCH SIZE
14" T R
12" T R R
10" T R R R
8" T R R R H
6" T R R R H H
4" T R R R H H H
3" T R R H H H H H
2" T R R H H H H H H
1½" T R R H H H H H H H
1" T R R H H H H H H H H
1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24"
HEADER SIZE
REFERENCES:
T Straight TEE.
R Reducing TEE.
H Stub-ins
Notes:
1.- This table gives the minimun requierement for the 90° branch connection in sizes shown.
Page 35 of 66
10704-P-ET-006
Rev: 0
TECHNICAL SPECIFICATION
SERVICE: BR2 (Brine liquids / Lithium 1,8 % WT / Lithium chloride liquor) / BR6 (Hot LiCl brine 30% and above,LOW Ca/Mg Brine, Rinse
water/brine, barium chloride trated brine, neutralized regenerant, low boron Ca/Mg Brine, Rinse water/spent regenerant, Rinse waste,
Lithuim 6% WT / ML2 (Mother liquor carbonate) / VT2 (Vent from tanks)
0
Page 36 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
SERVICE: HA2 (Hydrochloridic acid 30% and above) / HA3 (Hydrochloridic acid 8-20%)
PIPE GRP, Vinilester Resin PE, Butt and wrap jointing system 1" - 16" (1)(7)
FITTINGS GRP, Vinilester Resin PE, Butt and wrap jointing system 1" - 16" (1)(2)(5)(7)
FF ASME B16.5, PE Butt and wrap
FLANGES Integral GRP, Vinilester Resin 1" - 16" (6)(9)(10)
jointing system
BLIND FLANGE GRP, Vinilester Resin FF, ASME B16.5 1" - 16" (6)(10)(13)
Notes:
1.- Manufacturer to specify wall thickness suitable for pressure class and recommended ASTM D2996/ASTM D2310 Designation code. Outside
diameter, inside diameter and thickness shall be provided by the pipe manufacturer for review and approval. Wall thickness shall include:
a) Internal 5 mm thickness corrosion barrier of 2 layers of Nexus Veil Material (35 kg/m²) 90-95% of weight in resin. Corrosion barrier resin
shall be Type-A Bisphenol Epoxy Vinyl Ester Resin (Derakane 411; Hetron 922; Palatal 430 or equal). Resin Manufacturer shall submit
a resin recommendation verification/letter that the inner linner/corrosion barrier resin is suitable for service in the specified fluid and
pressure/temperature design conditions. The corrosion barrier reinforcement shall be Type-E Fiberglass MAT 450 gr/m² 60-65% of
weight in resin, to complete the linner thickness requirement.
b) Structural reinforcement shall be Filament Winding type with Type-E 2000Tex (2000 gr/m²) Fiberglass Continuos Roving with 30-35%
of weight in resin. Thickness shall be according to pressure/temperature design conditions.
c) External barrier shall have a synthetic or Fiberglass Veil for Corrosion protection, Identification and UV protection purposes.
2.- }
Structural reinforcement shall include Type-E Fiberglass MAT 450 gr/m² interlaying Bidirectional Ronving Veils according to:
a) 220 gr/m² for fittings up to 4 in., 50-60% of weight in Resin.
b) 600 gr/m² for fittings above to 4 in., 50-60% of weight in Resin.
3.- No additional material filler is permitted for GRP pipes, fittings and flanges. (e.g.: sand or recycled material).
4.- Visual examination shall be according to ASTM D2563-94 (Standard Practice for Classifying Visual Defects in Glass-Reinforced Plastic
Laminate Parts).
5.- Fittings shall be manufactured using Hand Lay-up Method and the recommendations of NBS-PS-15/69.
6.- Flanges shall be according to ASME B16.5 Class 150. When manufacturing special caution should be taken to avoid tears and material
delamination.
7.- Jointing system shall be according to DIN 16966 Part VIII, UHDE 303014, AFNOR-NFT 57900 and particular practices for Highly corrosive
chemicals. The use of fillers (others than those indicated) for bevels sealing is not permitted. Jointing shall be 100% wrapped. Beveled ends
shall be 18° or less to permitt the aplication of veils and fiberglass.
Page 37 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
SERVICE: HA2 (Hydrochloridic acid 30% and above) / HA3 (Hydrochloridic acid 8-20%)
TECHNICAL SPECIFICATION
32 to 149
TEMPERATURE ºF FLANGE CLASS: 150
DESIGN PRESSURE psig 150 MATERIAL: PRVF
CODE: DIN 16965 Part IV
CA: 0 mm
SERVICE: HA2 (Hydrochloridic acid 30% and above) / HA3 (Hydrochloridic acid 8-20%)
24"
20"
18"
16" T
BRANCH SIZE
14" T R
12" T R R
10" T R R R
8" T R R R H
6" T R R R H H
4" T R R R H H H
3" T R R H H H H H
2" T R R H H H H H H
1½" T R R H H H H H H H
1" T R R H H H H H H H H
1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24"
HEADER SIZE
REFERENCES:
T Straight TEE.
R Reducing TEE.
H Stub-ins
Notes:
1.- This table gives the minimun requierement for the 90° branch connection in sizes shown.
Page 39 of 66
10704-P-ET-006
Rev: 0
TECHNICAL SPECIFICATION
SERVICE: HA2 (Hydrochloridic acid 30% and above) / HA3 (Hydrochloridic acid 8-20%)
TECHNICAL SPECIFICATION
SERVICE: BR3 (Lithium carbonate - Reactor) / BR6 (Hot LiCl brine 30% and above,LOW Ca/Mg Brine, Rinse water/brine, barium chloride trated
brine, neutralized regenerant, low boron Ca/Mg Brine, Rinse water/spent regenerant, Rinse waste, Lithuim 6% WT
PIPE GRP, Vinilester Resin PE, Butt and wrap jointing system 1" - 16" (1)(7)
FITTINGS GRP, Vinilester Resin PE, Butt and wrap jointing system 1" - 16" (1)(2)(5)(7)
FF ASME B16.5, PE Butt and wrap
FLANGES Integral GRP, Vinilester Resin 1" - 16" (6)(9)(10)
jointing system
BLIND FLANGE GRP, Vinilester Resin FF, ASME B16.5 1" - 16" (6)(10)(13)
Notes:
1.- Manufacturer to specify wall thickness suitable for pressure class and recommended ASTM D2996/ASTM D2310 Designation code. Outside
diameter, inside diameter and thickness shall be provided by the pipe manufacturer for review and approval. Wall thickness shall include:
a) Internal 2 mm thickness antiabrasive/corrosion barrier of resin with anti abrasive filler (Tungsten carbide, Silicon carbide or equal) and
2 layers of Nexus Veil Material (35 kg/m²) 90-95% of weight in resin. Corrosion/antiabrasive barrier resin shall be Type-A Bisphenol
Epoxy Vinyl Ester Resin (Derakane 411; Hetron 922; Palatal 430 or equal). Resin Manufacturer shall submit a resin recommendation
verification/letter that the inner linner/corrosion barrier resin is suitable for service in the specified fluid and pressure/temperature
design conditions. The antiabrasive/corrosion barrier reinforcement shall be Type-E Fiberglass MAT 450 gr/m² 60-65% of weight in
resin, to complete the linner thickness requirement.
b) Structural reinforcement shall be Filament Winding type with Type-E 2000Tex (2000 gr/m²) Fiberglass Continuos Roving with 30-35%
of weight in resin. Thickness shall be according to pressure/temperature design conditions.
c) External barrier shall have a synthetic or Fiberglass Veil for Corrosion protection, Identification and UV protection purposes.
} Identification shall be done with RAL 7035 color.
2.- Structural reinforcement shall include Type-E Fiberglass MAT 450 gr/m² interlaying Bidirectional Ronving Veils according to:
a) 220 gr/m² for fittings up to 4 in., 50-60% of weight in Resin.
b) 600 gr/m² for fittings above to 4 in., 50-60% of weight in Resin.
3.- No additional material filler is permitted for GRP pipes, fittings and flanges. (e.g.: sand or recycled material).
4.- Visual examination shall be according to ASTM D2563-94 (Standard Practice for Classifying Visual Defects in Glass-Reinforced Plastic
Laminate Parts).
5.- Fittings shall be manufactured using Hand Lay-up Method and the recommendations of NBS-PS-15/69.
6.- Flanges shall be according to ASME B16.5 Class 150. When manufacturing special caution should be taken to avoid tears and material
delamination.
7.- Jointing system shall be according to DIN 16966 Part VIII, UHDE 303014, AFNOR-NFT 57900 and particular practices for Highly corrosive
chemicals. The use of fillers (others than those indicated) for bevels sealing is not permitted. Jointing shall be 100% wrapped. Beveled ends
shall be 18° or less to permitt the aplication of veils and fiberglass.
Page 41 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
SERVICE: BR3 (Lithium carbonate - Reactor) / BR6 (Hot LiCl brine 30% and above,LOW Ca/Mg Brine, Rinse water/brine, barium chloride trated
brine, neutralized regenerant, low boron Ca/Mg Brine, Rinse water/spent regenerant, Rinse waste, Lithuim 6% WT
TECHNICAL SPECIFICATION
32 to 194
TEMPERATURE ºF FLANGE CLASS: 150
DESIGN PRESSURE psig 150 MATERIAL: PRVF
CODE: DIN 16965 Part IV
CA: 0 mm
SERVICE: BR3 (Lithium carbonate - Reactor) / BR6 (Hot LiCl brine 30% and above,LOW Ca/Mg Brine, Rinse water/brine, barium
chloride trated brine, neutralized regenerant, low boron Ca/Mg Brine, Rinse water/spent regenerant, Rinse waste, Lithuim
6% WT
24"
20"
18"
16" T
BRANCH SIZE
14" T R
12" T R R
10" T R R R
8" T R R R H
6" T R R R H H
4" T R R R H H H
3" T R R H H H H H
2" T R R H H H H H H
1½" T R R H H H H H H H
1" T R R H H H H H H H H
1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24"
HEADER SIZE
REFERENCES:
T Straight TEE.
R Reducing TEE.
H Stub-ins
Notes:
1.- This table gives the minimun requierement for the 90° branch connection in sizes shown.
Page 43 of 66
10704-P-ET-006
Rev: 0
TECHNICAL SPECIFICATION
SERVICE: BR3 (Lithium carbonate - Reactor) / BR6 (Hot LiCl brine 30% and above,LOW Ca/Mg Brine, Rinse water/brine, barium chloride trated
brine, neutralized regenerant, low boron Ca/Mg Brine, Rinse water/spent regenerant, Rinse waste, Lithuim 6% WT
TECHNICAL SPECIFICATION
GENERAL REQUIREMENTS
VALVES DATASHEET
VALVE IDENTIFICATION
References:
E.B.: Extended Bonnet
R.B.: Reduced Bore
F.B.: Full Bore
IDENTIFIER MATERIAL
A LOW ALLOY STEEL TYPEP11
B BRONZE
C CARBON STEEL
D DUPLEX
E CAST IRON PTFE/PFA LINED
F CAST IRON PP LINED
I CAST IRON
L LOW TEMPERATURE CARBON STEEL
M MONEL (ALLOY 400)
N NODULAR CAST IRON
P PVDF
S STAINLESS STEEL Type 316
T STAINLESS STEEL Type 316 L
U STAINLESS STEEL Type 304
V STAINLESS STEEL Type 304 L
W PVC-U
Page 45 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
GENERAL REQUIREMENTS
IDENTIFIER TRIM
A API Trim 1
B API Trim 8
C ASTM A 105 + ENP
D API Trim 12
E API Trim 5
F ASTM A 350 Gr.LF2 + ENP
G API Trim 10
H API Trim 11 (MONEL)
I STAINLESS STEEL Type 304
J STAINLESS STEEL Type 316
K EPDM
L PTFE/PFA Lined
M MONEL (ALLOY 400)
N BRONZE
P PVDF
S STAINLESS STEEL Type 304 L
T STAINLESS STEEL Type 316 L
U PVC-U
V PP Lined
R API Trim 15
X API Trim 16
IDENTIFIER RATING
1 150#
2 2500#
3 300#
4 125#
5 5000
6 600#
7 1500#
8 800#
9 900#
0 Non Rating
Page 46 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
GENERAL REQUIREMENTS
IDENTIFIER ENDS
B BUTT WELDING
D DOUBLE FLANGED
E WAFER - RTJ
F FF
J RTJ
L LUG - RF
N THREADED NPT
R RF
S SOCKET WELD
T SOCKET WELD x THREADED NPT
W WAFER - RF
IDENTIFIER OPERATION
G GEAR BOX
H HANDWHEEL
W WRENCH / LEVER
D DUAL PLATE
C CHAINWHEEL
P PISTON CHECK
S SWING CHECK
0 N/A
TECHNICAL SPECIFICATION
GENERAL REQUIREMENTS
1 2 3 4 5 6 7 5
G C A 1 R H E N
GATE VALVE CARBON STEEL API Trim 1 150# RF HANDWHELL E.S NACE
Page 48 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
Standar
E Extended Stem
NEEDLE VALVE COMMODITY REF.NOTE
VALVE TYPE: NUG7NH0 L Locking Device
RISING STEM CODE: NUMBER
Extended Stem and
Y
Locking Device
RATING: CLASS 1500
VALVE DESIGN: API STD 602
SIZE RANGE: 1/4" - 2"
SUPLEMENTARY
REQUIREMENTS
NOTES:
1- Marking shall be according to MSS-SP25. Each valve shall be provided with a Stainless Steel plate showing its corresponding
commodity code. If the plate attachment is not possible, Commodity Code shall be etched to the body
Page 49 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
Standar
E Extended Stem
GATE VALVE COMMODITY REF.NOTE
VALVE TYPE: ECE8SH0 L Locking Device
OS&Y CODE: NUMBER
Extended Stem and
Y
Locking Device
RATING: CLASS 800
VALVE DESIGN: API STD 602 - FULL PORT
SIZE RANGE: 1/2" - 1 1/2"
DESIGN PRESSURE: ASME B16.34
GENERAL 1
BODY/BONNET JOINT BOLTED
END TO END STD: MANUFACTURER'S STANDARD
END CONNECTIONS SW (ASME B16.11)
END EXTENSION NO
OPERATION HANDWHEEL
DISC / SEAT TYPE SOLID WEDGE / RENEWABLE
MATERIALS
BODY ASTM A105
BONNET ASTM A105
STEM TRIM 5
WEDGE TRIM 5
SEAT TRIM 5
GASKET SPIRAL WOUND TYPE 304 SS W/ GRAPHITE FILL
PACKING JOHN CRANE 387I OR SIMILAR
BOLTING ASTM A193 Gr.B7 (Studs) / ASTM A194 Gr.2H (Nuts)
TESTING
SUPLEMENTARY
REQUIREMENTS
1- Marking shall be according to MSS-SP25. Each valve shall be provided with a Stainless Steel plate showing its corresponding
commodity code. If the plate attachment is not possible, Commodity Code shall be etched to the body
Page 50 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
Standar
E Extended Stem
GATE VALVE COMMODITY REF.NOTE
VALVE TYPE: ECE1RH0 L Locking Device
OS&Y CODE: NUMBER
Extended Stem and
Y
Locking Device
RATING: CLASS 150
VALVE DESIGN: API STD 600
SIZE RANGE: 2" - 8"
DESIGN PRESSURE: ASME B16.34
GENERAL 2
BODY/BONNET JOINT BOLTED
FACE TO FACE STD: ASME B16.10
END CONNECTIONS FLANGED RF (ASME B16.5) 1
END EXTENSION NO
OPERATION HANDWHEEL
DISC / SEAT TYPE FLEXIBLE WEDGE / RENEWABLE or INTEGRAL
MATERIALS
BODY ASTM A216 Gr. WCB
BONNET ASTM A216 Gr. WCB
STEM TRIM 5
WEDGE TRIM 5
SEAT TRIM 5
BONNET GASKET SPIRAL WOUND TYPE 304 SS W/ GRAPHITE FILL
PACKING FLEXIBLE GRAPHITE
BOLTING ASTM A193 Gr.B7 (Studs) / ASTM A194 Gr.2H (Nuts)
TESTING
SUPLEMENTARY
REQUIREMENTS
TECHNICAL SPECIFICATION
Standard
BALL VALVE E Extended Stem
COMMODITY REF.NOTE
VALVE TYPE: RCJ8SW0 L Locking Device
CODE: NUMBER
FLOATING BALL Extended Stem and
Y
Locking Device
RATING: CLASS 800
VALVE DESIGN: ISO 17292
SIZE RANGE: 1/2" - 1 1/2"
BORE SIZE: REDUCED
FIRE-SAFE
ISO 10497 / API 607
CERTIFICATION
OTHER BIDIRECTIONAL, BLOW-OUT PROOF STEM, ANTI-STATIC DEVICE, FIRE-SAFE,
REQUIREMENTS POSITION INDICATOR.
NOTES:
TECHNICAL SPECIFICATION
Standard
BALL VALVE E Extended Stem
COMMODITY REF.NOTE
VALVE TYPE: RCC1RW0 L Locking Device
CODE: NUMBER
FLOATING BALL Extended Stem and
Y
Locking Device
RATING: CLASS 150
VALVE DESIGN: API 6D
SIZE RANGE: 2" - 6"
BORE SIZE: REDUCED
FIRE-SAFE
ISO 10497 / API 607
CERTIFICATION
OTHER BIDIRECTIONAL, BLOW-OUT PROOF STEM, ANTI-STATIC DEVICE, FIRE-SAFE,
REQUIREMENTS POSITION INDICATOR.
NOTES:
TECHNICAL SPECIFICATION
Standard
BALL VALVE E Extended Stem
COMMODITY REF.NOTE
VALVE TYPE: RBN8NW0 L Locking Device
CODE: NUMBER
FLOATING BALL Extended Stem and
Y
Locking Device
RATING: CLASS 800
VALVE DESIGN: ISO 17292
SIZE RANGE: 1/4" - 2"
BORE SIZE: REDUCED
SEALS PTFE
GASKET PTFE
TESTING
FIRE-SAFE
CERTIFICATION
OTHER BIDIRECTIONAL
REQUIREMENTS POSITION INDICATOR.
NOTES:
1- Marking shall be according to MSS-SP25. Each valve shall be provided with a Stainless Steel plate showing its corresponding
commodity code. If the plate attachment is not possible, Commodity Code shall be etched to the body
Page 54 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
Standard
BALL VALVE E Extended Stem
COMMODITY REF.NOTE
VALVE TYPE: RUJ8SW0 L Locking Device
CODE: NUMBER
FLOATING BALL Extended Stem and
Y
Locking Device
RATING: CLASS 800
VALVE DESIGN: ISO 17292
SIZE RANGE: 1/2" - 1 1/2"
BORE SIZE: REDUCED
FIRE-SAFE
ISO 10497 / API 607
CERTIFICATION
OTHER BIDIRECTIONAL, BLOW-OUT PROOF STEM, ANTI-STATIC DEVICE, FIRE-SAFE,
REQUIREMENTS POSITION INDICATOR.
NOTES:
TECHNICAL SPECIFICATION
Standard
BALL VALVE E Extended Stem
COMMODITY REF.NOTE
VALVE TYPE: RSJ1RW0 L Locking Device
CODE: NUMBER
FLOATING BALL Extended Stem and
Y
Locking Device
RATING: CLASS 150
VALVE DESIGN: API 6D
SIZE RANGE: 2" - 6"
BORE SIZE: REDUCED
FIRE-SAFE
ISO 10497 / API 607
CERTIFICATION
OTHER BIDIRECTIONAL, BLOW-OUT PROOF STEM, ANTI-STATIC DEVICE, FIRE-SAFE,
REQUIREMENTS POSITION INDICATOR.
NOTES:
TECHNICAL SPECIFICATION
Standard
BALL VALVE E Extended Stem
COMMODITY REF.NOTE
VALVE TYPE: RTT8SW0 L Locking Device
CODE: NUMBER
FLOATING BALL Extended Stem and
Y
Locking Device
RATING: CLASS 800
VALVE DESIGN: ISO 17292
SIZE RANGE: 1/2" - 1 1/2"
BORE SIZE: REDUCED
FIRE-SAFE
ISO 10497 / API 607
CERTIFICATION
OTHER BIDIRECTIONAL, BLOW-OUT PROOF STEM, ANTI-STATIC DEVICE, FIRE-SAFE,
REQUIREMENTS POSITION INDICATOR.
NOTES:
TECHNICAL SPECIFICATION
Standard
BALL VALVE E Extended Stem
COMMODITY REF.NOTE
VALVE TYPE: REL1RW0 L Locking Device
CODE: NUMBER
FLOATING BALL Extended Stem and
Y
Locking Device
RATING: CLASS 150
VALVE DESIGN: API 6D
SIZE RANGE: 1" - 6"
BORE SIZE: REDUCED
FIRE-SAFE
--
CERTIFICATION
OTHER BIDIRECTIONAL, BLOW-OUT PROOF STEM, ANTI-STATIC DEVICE
REQUIREMENTS POSITION INDICATOR.
NOTES:
TECHNICAL SPECIFICATION
Standard
BALL VALVE E Extended Stem
COMMODITY REF.NOTE
VALVE TYPE: RST1RW0 L Locking Device
CODE: NUMBER
FLOATING BALL Extended Stem and
Y
Locking Device
RATING: CLASS 150
VALVE DESIGN: API 6D
SIZE RANGE: 2" - 6"
BORE SIZE: REDUCED
FIRE-SAFE
ISO 10497 / API 607
CERTIFICATION
OTHER BIDIRECTIONAL, BLOW-OUT PROOF STEM, ANTI-STATIC DEVICE, FIRE-SAFE,
REQUIREMENTS POSITION INDICATOR.
NOTES:
TECHNICAL SPECIFICATION
Standard
BALL VALVE E Extended Stem
COMMODITY REF.NOTE
VALVE TYPE: RMM8SW0 L Locking Device
CODE: NUMBER
FLOATING BALL Extended Stem and
Y
Locking Device
RATING: CLASS 800
VALVE DESIGN: ISO 17292
SIZE RANGE: 1/2" - 1 1/2"
BORE SIZE: REDUCED
FIRE-SAFE
ISO 10497 / API 607
CERTIFICATION
OTHER BIDIRECTIONAL, BLOW-OUT PROOF STEM, ANTI-STATIC DEVICE, FIRE-SAFE,
REQUIREMENTS POSITION INDICATOR.
NOTES:
TECHNICAL SPECIFICATION
Standard
PLUG VALVE E Extended Stem
COMMODITY REF.NOTE
VALVE TYPE: PEL1RW0 L Locking Device
CODE: NUMBER
FULL PORT Extended Stem and
Y
Locking Device
RATING: CLASS 150
VALVE DESIGN: API 6D
SIZE RANGE: 1" - 6"
BORE SIZE: FULL PORT
FIRE-SAFE
API 607
CERTIFICATION
OTHER BIDIRECTIONAL, BLOW-OUT PROOF STEM, ANTI-STATIC DEVICE, FIRE-SAFE,
REQUIREMENTS POSITION INDICATOR.
NOTES:
TECHNICAL SPECIFICATION
Standard
BUTTERFLY VALVE E Extended Stem
COMMODITY REF.NOTE
VALVE TYPE: BEL1LW0 L Locking Device
CODE: NUMBER
Extended Stem and
Y
Locking Device
RATING: 150 psi
VALVE DESIGN: API STD 609
SIZE RANGE: 3" - 24"
DESIGN PRESSURE: 150 psi
GENERAL
FACE TO FACE STD: API STD 609
END CONNECTIONS LUG-TYPE FOR MOUNTING BETWEEN FLANGES RF (ASME B16.5)
OPERATION TO BE DEFINED BY VENDOR
MATERIALS
BODY ASTM A395 Gr. 60-40-18, PFA Lined
STEM 17-4 PH PTFE encapsulated
DISC ASTM A351 Gr. CF8M PTFE encapsulated
SEAT TFE / INCONEL
PACKING SEAL PTFE
TESTING
PRESSURE TESTING API STD 598
FIRE-SAFE
--
CERTIFICATION
SUPLEMENTARY
DISC POSITION INDICATOR.
REQUIREMENTS
NOTES:
2- Marking shall be according to MSS-SP25. Each valve shall be provided with a Stainless Steel plate showing its corresponding
commodity code. If the plate attachment is not possible, Commodity Code shall be etched to the body
Page 62 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
Standar
E Extended Stem
CHECK VALVE COMMODITY REF.NOTE
VALVE TYPE: CEL1WS0 L Locking Device
Swing CODE: NUMBER
Extended Stem and
Y
Locking Device
RATING: CLASS 150
VALVE DESIGN: API STD 594
SIZE RANGE: 2" - 6"
DESIGN PRESSURE: --
GENERAL 3, 4
FACE TO FACE STD: ASME B16.5 table 9 col 3
END CONNECTIONS WAFER TYPE FOR MOUNTING BETWEEN FLANGES RF (ASME B16.5)
SEAT TYPE INTEGRAL
MATERIALS 2
BODY ASTM A395 Gr. 60-40-18, PFA Lined
DISC ASTM A395 Gr. 60-40-18, PFA Lined
SEAT SURFACE ASTM A395 Gr. 60-40-18, PFA Lined
SPRING to be defined by vendor
TESTING
SUPLEMENTARY
REQUIREMENTS
NOTES:
TECHNICAL SPECIFICATION
Standar
E Extended Stem
CHECK VALVE COMMODITY REF.NOTE
VALVE TYPE: CMH1WD0 L Locking Device
DUAL-PLATE CODE: NUMBER
Extended Stem and
Y
Locking Device
RATING: CLASS 150
VALVE DESIGN: API STD 594 TYPE "A"
SIZE RANGE: 2" - 12"
DESIGN PRESSURE: ASME B16.34
GENERAL 3, 4
FACE TO FACE STD: API STD 594 TYPE "A"
END CONNECTIONS WAFER-TYPE FOR MOUNTING BETWEEN FLANGES RF (ASME B16.5) 1
SEAT TYPE INTEGRAL
MATERIALS 2
BODY ASTM B562 UNS N04400
DISC TRIM 11
SEAT SURFACE TRIM 11
SPRING INCONEL X-750
TESTING
SUPLEMENTARY
REQUIREMENTS
NOTES:
TECHNICAL SPECIFICATION
Standar
E Extended Stem
CHECK VALVE COMMODITY REF.NOTE
VALVE TYPE: CTT8SP0 L Locking Device
PISTON-TYPE CODE: NUMBER
Extended Stem and
Y
Locking Device
RATING: CLASS 800
VALVE DESIGN: API STD 602
SIZE RANGE: 1/2" - 1 1/2"
DESIGN PRESSURE: ASME B16.34
GENERAL 1
BODY/BONNET JOINT BOLTED
FACE TO FACE STD: MANUFACTURER'S STANDARD
END CONNECTIONS SW (ASME B16.11)
MATERIALS
BODY ASTM A182 Gr. F316L
BONNET ASTM A182 Gr. F316L
DISC TRIM 12
SEAT TRIM 12
GASKET SPIRAL WOUND TYPE 304 SS W/ GRAPHITE FILL
BOLTING ASTM A193 Gr.B8M (Studs) / ASTM A194 Gr 8MA (Nuts)
TESTING
SUPLEMENTARY
REQUIREMENTS
NOTES:
1- Marking shall be according to MSS-SP25. Each valve shall be provided with a Stainless Steel plate showing its corresponding
commodity code. If the plate attachment is not possible, Commodity Code shall be etched to the body
Page 65 of 66
10701-P-LI-009
Rev: 0
TECHNICAL SPECIFICATION
Standar
E Extended Stem
GLOBE VALVE COMMODITY REF.NOTE
VALVE TYPE: GSD1RH0 L Locking Device
OS&Y CODE: NUMBER
Extended Stem and
Y
Locking Device
RATING: CLASS 150
VALVE DESIGN: BS 1873
SIZE RANGE: 2" - 12"
DESIGN PRESSURE: ASME B16.34
GENERAL 2
BODY/BONNET JOINT BOLTED
FACE TO FACE STD: ASME B16.10
END CONNECTIONS FLANGED RF (ASME B16.5) 1
END EXTENSION NO
OPERATION HANDWHEEL
DISC / SEAT TYPE PLUG TYPE / RENEWABLE
MATERIALS
BODY ASTM A351 Gr. CF8M
BONNET ASTM A351 Gr. CF8M
STEM TRIM 12
DISC TRIM 12
SEAT TRIM 12
BONNET GASKET GRAPHITE W / 316 SS CORE
PACKING JOHN CRANE 387I OR SIMILAR
BOLTING ASTM A193 Gr.B8M (Studs) / ASTM A194 Gr.8M (Nuts)
TESTING
SUPLEMENTARY
REQUIREMENTS
NOTES:
TECHNICAL SPECIFICATION
Standar
E Extended Stem
COMMODITY REF.NOTE
VALVE TYPE: DIAPHRAGM VALVE DFK4FH0 L Locking Device
CODE: NUMBER
Extended Stem and
Y
Locking Device
RATING: CLASS 125
SIZE RANGE: 1" - 6"
DESIGN PRESSURE: ASME B16.34
GENERAL 2
BODY/BONNET JOINT BOLTED
FACE TO FACE STD: ASME B16.10
END CONNECTIONS FLANGED FF (ASME B16.5) 1
END EXTENSION NO
OPERATION HANDWHEEL
MATERIALS
BODY ASTM A395 Gr. 60-40-18, PP Lined
COVER ASTM A395 Gr. 60-40-18, PP Lined
COMPRESSOR ASTM A395 Gr. 60-40-18
DIAPHRAGM EPDM
BONNET GASKET EPDM
BOLTING ASTM A193 Gr.B7 (Studs) / ASTM A194 Gr.2H (Nuts)
TESTING
SUPLEMENTARY
REQUIREMENTS
NOTES:
2- Marking shall be according to MSS-SP25. Each valve shall be provided with a Stainless Steel plate showing its corresponding
commodity code. If the plate attachment is not possible, Commodity Code shall be etched to the body