Beruflich Dokumente
Kultur Dokumente
narr
epor
t
on
NON-
DESTRUCTI
VETESTI
NGOFCONCRETE
submi
tt
edby
MANMOHANLODHA
15CE25
I
npar
ti
alf
ulf
il
lmentoft
heawar
doft
hedegr
ee
of
BACHELOROFTECHNOLOGY
i
n
CI
VILENGI
NEERI
NG
at
DEPARTMENTOFCI
VILENGI
NEERI
NG
GOVERNMENTENGI
NEERI
NGCOLLEGE
AJMER
ACKNOWLEDGEMENT
It gives me immense pleasure to express my deepest sense of gratitude to my supervisors Mr.
Pravesh Saini Sir and Mr. Anurag Kumar Singh Sir for their invaluable guidance, comments and
help throughout the course of the project. Their useful suggestions for this whole work and
cooperative behavior are sincerely acknowledged.
I would also like to thank Dr. Ganpat Singh Sir, HOD Civil Engineering Department for his
constant motivation and support during the seminar report.
I also wish to express my indebtedness to my parents as well as my family members whose
blessings and support always helped me to face the challenges ahead.
In the end I would like to express my sincere thanks to all my friends and others who helped me
directly or indirectly during this project work.
Manmohan Lodha
B.Tech IVth Year
Civil Engg.
i
ABSTRACT
Concrete is the combination of cement mortar and binders and is of wide use in many places. Its
applications range from small covering slabs to huge buildings. The necessity to know the strength
its ability to withstand load and durability is a factor of grave concern. The existence of the building
is entirely relied on the concrete structure it is made of. Based on the mixing proportions,
composition and wetting the properties of concrete can vary. Hence it is necessary to test concrete
strength wherever possible.
Although there can be no direct measurement of the strength properties of structural concrete for
the simple reason that strength determination involves destructive stresses, several non -
destructive methods of assessment have been developed. These depend on the fact that certain
physical properties of concrete can be related to strength and can be measured by non-destructive
methods.
ii
TABLE OF CONTENT
ACKNOWLEDGEMENT (i)
ABSTRACT (ii)
1. INTRODUCTION 1
1.1. NON-DESTRUCTIVE TESTING OF CONCRETE 1
2. LITERATURE REVIEW 3
2.1. DESTRUCTIVE TESTING OF CONCRETE 3
2.2. NON-DESTRUCTIVE TESTING OF CONCRETE 3
3. OJECTIVES AND IMPORTANCE OF NDT 5
3.1. OBJECTIVES 5
3.2. IMPORTANCE 5
4. NON-DESTRUCTIVE TESTING METHODS 6
4.1. SURFACE HARDNESS METHODS 6
4.1.1. PRINCIPLE OF TEST 6
4.1.2. PROCEDURE 8
4.2. PENETRATION RESISTANCE METHOD 8
4.2.1. TEST EQUIPMENT 8
4.2.2. LIMITATIONS AND ADVANTAGES 10
4.3. PULL-OUT RESISTANCE METHOD 10
4.3.1. PROCEDURE 11
4.3.2. LIMITATIONS AND ADVANTAGES 11
4.4. RESONANCE FREQUENCY METHOD 11
4.4.1. TEST EQUIPMENT 11
4.4.2. PRINCIPLE OF TEST 11
4.5. MATURITY TEST METHOD 13
4.5.1. PRINCIPLE OF TEST 13
4.6. PERMEATION TEST METHOD 14
4.6.1. PROCEDURE 14
4.7. IMPACT-ECHO METHOD 15
4.7.1. PRINCIPLE OF TEST 15
iii
4.8. ULTRA SONIC PULSE VELOCITY METHOD 15
4.8.1. TEST EQUIPMENT 16
4.8.2. TRANSDUCER ARRANGEMENT 17
4.9. CORE CUTTER METHOD 17
4.9.1. PROCEDURE 18
5. CONCLUSIONS 19
5.1. FOR REBOUND HAMMER TEST 19
5.2. FOR PENETRATION TEST 19
5.3. FOR PULL-OUT TECHNIQUE 19
5.4. FOR RESONANCE FREQUENCY METHOD 19
5.5. FOR MATURITY TEST 19
5.6. FOR PERMEATION TEST 19
5.7. FOR IMPACT-ECHO METHOD 20
5.8. FOR ULTRASONIC PULSE VELOCITY TEST 20
5.9. FOR CORE CUTTER TEST 20
6. FUTURE OF NON-DESTRUCTIVE TESTING 21
REFERENCES 22
iv
LIST OF FIGURES
v
CHAPTER 1
INTRODUCTION
Non-destructive testing (NDT) is a wide group of analysis techniques used in science and
technology industry to evaluate the properties of a material, component or system without
causing damage.
When the inspection and test is done, that part of structure can still be used.
The destructive test are often used to determine physical properties of material such as
impact resistance, ductility, yield and ultimate tensile strength, fracture toughness and
fatigue strength, but discontinuities and differences in material characteristics are more
effectively found by NDT.
These tests are used in manufacturing, fabrication and in-service inspection to ensure
product integrity and reliability, to control manufacturing processes, lower production
costs and to maintain a uniform quality level.
It is a highly valuable technique that can save both money and time in product evaluation,
troubleshooting and research.
It is commonly used in forensic engineering, mechanical engineering, petroleum
engineering, electrical engineering, civil engineering, systems engineering, aeronautical
engineering, medicine, and art.
The purpose of NDT is to determine the quality and integrity of materials, components
or assemblies without affecting the ability to perform their intended functions.
For example, Coring is a common NDT method which alters the appearance of the component
and marginally affects its structural integrity. If done correctly, coring maintains the
serviceability of the structural component and is thus considered to be non-destructive.
1
The non-destructive Testing (NDT) plays an important role in assuring that structural and
mechanical components perform their function in a safe, reliable, and cost-effective manner.
NDT is typically used at various points in a part's life cycle.
NDT can be used prior to the use of a component for the sake of quality control. NDT is also
employed while components are in use to detect service related conditions caused by wear,
fatigue, corrosion, stress or other factors which affect reliability.
NDT methods have materialized as a response to the need for structural damage detection and
prevention. The extensive use of NDT is driven by economics and safety. In a pre-emptive
attempt to eradicate the problems associated with structural deterioration, novel in-site testing
techniques have been invented to allow for the assessment of concrete during the construction,
commissioning and servicing lifecycle stages of a structure
2
CHAPTER 2
LITERATURE REVIEW
3
2.) Ultrasonic pulse velocity test
3.) Rebound hammer test
4.) Core cutter test etc.
Extensive attempts and advancement have been made to develop NDT methods capable of
indicating mechanical, acoustical, chemical, electrical, magnetic and physical properties of
materials.
The first recorded uses of NDT was in 1868, when Englishman S.H. Saxby relied on the
magnetic characteristics of a compass to find cracks in gun barrels.
One of the earliest attempts of NDT dates to the 19th century where cracks were detected in
railroad wheels by means of acoustic tap testing (Stanley, 1995).
The first NDT method to come into industrial application was the X-ray technology. In 1895,
German physicist Wilhelm Conrad Rontgen’s experiment led him to discover X-rays, an
invention that earned him the first-ever Nobel Prize.
In 1929, a Russian named Sokolov proposed the use of ultrasound for testing castings. More
sensitive, reliable and quantifiable NDT methods have expansively emerged in recent years.
NDT has come a long way since the early years, and those of us involved in the industry today
owe a debt of gratitude to these pioneers, many of whom never lived to see the fruit of their labor.
Had it not been for their efforts, non-destructive testing as an industry might not even exist.
4
CHAPTER 3
3.1. OBJECTIVES :-
To control manufacturing processes.
Lower manufacturing costs.
Maintain uniform quality level.
Ensure operational readiness.
Make a profit for the user.
To aid in better product design.
To avoid failures, prevent accidents and save human life.
3.2. IMPORTANCE :-
Various tests can be performed on the same product.
Tests parts are not damaged.
Specimen preparation not required.
Can be performed on parts that are in service.
Low time consumption.
Low labor cost.
5
CHAPTER 4
Assessing the likely compressive strength of concrete with the help of suitable
correlations between rebound index and compressive strength.
Assessing the uniformity of concrete.
Assessing the quality of the concrete in relation to standard requirements.
Assessing the quality of one element of concrete in relation to another.
4.1.1. PRINCIPLE OF TEST :- Upon impact with the concrete surface, the rebounded hammer
records a rebound number which presents an indication of strength properties by referencing
established empirical correlations between strength properties of concrete (compressive and
flexural) and the rebound number.
6
Figure 4.1(a) : Schmidt Rebound Hammer
7
4.1.2. PROCEDURE :-
A visual examination of the concrete surface should be conducted prior to the test in
order to identify a smooth surface suitable for testing.
The test can be conducted in any directional angle where calibration charts are used to
mitigate the different effects of gravity.
The hammer is pressed against the concrete surface until a spring loaded mass is released
causing the plunger to impact against the surface and rebound a distanced measured by a
slide indicator.
The measured distance is referred to as the rebound number.
4.2. PENETRATION RESISTANCE METHOD :- These methods involve driving probes into
concrete samples using a uniform force. Measuring the probe's depth of penetration provides an
indication of concrete compressive strength by referring to correlations.
The most commonly used penetration resistance method is the Windsor probe system. The
system consists of a powder-actuated gun, which drives hardened allow-steel probes into
concrete samples while measuring penetration distance via a depth gauge.
8
Hardened alloy probe (diameter 6.5mm and length 80mm) (Driven into the concrete by
means of a precision powder charge),
Loaded cartridges and
A depth gauge for measuring penetration of probes.
The strength properties of both mortar and stone aggregate influence the penetration depth of the
probe in a concrete. Thus the type of stone aggregate has a strong effect on the relation of
concrete strength v/s depth of penetration. For two samples of concrete with equal cube crushing
strength, penetration depth would be more in the sample with softer aggregate than the one with
harder aggregates.
Correlation of the penetration resistance to compressive strength is based on calibration curves
obtained from laboratory test on specific concrete with particular type of aggregates.
9
4.2.2. LIMITATIONS AND ADVANTAGES :-
The Windsor probe system is quick, cheap and simple to operate.
As with surface hardness methods, the penetration resistance methods do not yield
absolute values of strength and must therefore be used as a method of testing variability
of strength properties between concrete samples.
It also provides a means of assessing strength development with curing.
This test is essentially non-destructive, since concrete and structural members can be
tested in situ, with only minor patching of holes on exposed faces.
4.3. PULL-OUT RESISTANCE METHOD :- Pull-out resistance methods measure the force
required to extract standard embedded inserts from the concrete surface. Using established
correlations, the force required to remove the inserts provides an estimate of concrete strength
properties.
Two types of inserts, cast-in and fixed-in-place, define the two types of pull-out methods.
Cast-in tests require an insert to be positioned within the fresh concrete prior to its placement.
Fixed-in-place tests require less foresight and involve positioning an insert into a drilled hole
within hardened concrete.
10
4.3.1. PROCEDURE :- The most commonly used pull-out test method is the LOK test
developed in 1962 by Kierkegaard-Hansen (Kierkegaard-Hansen, 1975). The test requires an
insert embedment of 25 mm to insure sufficient testing of concrete with coarse aggregates.
A pull-out test measures, with a special ram, the force require to pull from the concrete a
specially shaped steel rod whose enlarged end has been cast into the concrete to a depth of 7.6
cm.
The concrete is simultaneously in tension and in shear, but the force required to pull the
concrete out can be related to its compressive strength.
4.3.2. LIMITATIONS AND ADVANTAGES :-
Pull-out tests do not measure the interior strength of mass concrete, they do give
information on the maturity and development of strength of are preventative part of it.
Such tests have the advantage of measuring quantitatively the strength of concrete in
place.
Their main disadvantage is that they have to be planned in advance and pull out
assemblies set into the formwork before the concrete is placed.
The pull-out of course creates some minor damage.
4.4. RESONANCE FREQUENCY METHOD :- Resonant frequency methods are non-
invasive non-destructive tests that are conducted to determine material properties by measuring
their natural frequency of vibration.
The two categories of resonant frequency methods are resonant frequency by vibration and
resonant frequency by impact.
11
N=(m²k/2πL²)√(E/d)
E=(4π²L⁴N²d)/(m⁴k²)
where E = dynamic modulus of elasticity, d = density of the material, L = length of the specimen,
N = fundamental flexural frequency, k = radius of gyration, and m = a constant (4.73 for the
fundamental mode of vibration).
12
Resonant frequency methods provide an excellent means for studying the effects of extreme
temperature changes and loading.
4.5. MATURITY TEST METHOD :- The maturity method is a NDT technique for
determining strength gain of concrete based on the measured temperature history during curing.
The maturity method has various applications in concrete construction such as formwork
removal and post-tensioning.
14
4.7. IMPACT-ECHO METHOD :- The impact-echo system is a recent development of
ultrasonic methods which involves the measuring of concrete thickness and integrity using one
surface. The test is also applied to determine the location of cracking, voids and delamination.
It is based on monitoring the surface motion of concrete resulting from a short-duration
mechanical impact. Specifically, the test measures the amplitude of reflected shock waves to
detect flaws in concrete.
4.7.1. PRINCIPLE OF TEST :- The impact-echo system uses an electro-mechanical transducer
to generate a short pulse of ultrasonic stress waves that propagates into concrete plate-like
structures. The different materials of different densities and elastic properties will reflect the
stress pulse at their boundaries.
The reflected pulse travels back to the transducer, which also acts as a receiver. An oscilloscope
displays the received signal and the round trip travel time of the pulse is measured electronically.
The distance of the reflecting interface can be determined by knowing the speed of the stress
wave.
The factors that affect the detection of a flaw within concrete are :-
The type of the flaw and its orientation,
The depth of the flaw and
The contact time of the impact.
4.8. ULTRA SONIC PULSE VELOCITY METHOD :-
Ultrasonic pulse velocity methods involve propagating ultrasonic waves in solids while
measuring the time taken for the waves to propagate between a sending and receiving
point.
The features of ultrasonic wave propagation can be used to characterize a composition,
structure, elastic properties, density and geometry using previously established
correlations, known patterns and mathematical relationships.
This non-invasive technique is also used to detect and describe flaws in material as well
as their severity of damage by observing the scattering of ultrasonic waves.
Amplifier and
17
The general rule adopted for fixing the core size, besides the H/D ratio, is the nominal
size of stone aggregate and the dia. should be not less than 3 times the maximum size of
stone aggregate.
For diameter of core less than 3 times the size of the stone aggregate, an increased
number of cores have to be tested.
The core samples can also be used for the following:
1.) Strength and density determination
2.) Depth of carbonation of concrete
3.) Chemical analysis
4.) Water/gas permeability
5.) Petrographic analysis
4.9.1. PROCEDURE :-
Concrete cores are usually cut by means of a rotary cutting tool with diamond bits.
In this manner, a cylindrical specimen is obtained usually with its ends being uneven,
parallel and square and sometimes with embedded pieces of reinforcement.
The cores are visually described and photographed, giving specific attention to
compaction, distribution of aggregates, presence of steel etc.
The core should then be soaked in water, capped with molten sulphur to make its ends
plane, parallel, at right angle and then tested in compression in a moist condition.
Factors Affecting Strength of Concrete Cores :-
Size of stone aggregate,
Presence of transverse reinforcement steel,
H/D ratio,
Age of concrete,
Strength of concrete and
Drilling operations.
18
CHAPTER 5
CONCLUSIONS
5.1. FOR REBOUND HAMMER TEST :- The rebound hammer method could be used for :-
1. Assessing the likely compressive strength of concrete with the help of suitable
correlations between rebound index and compressive strength.
2. Assessing the uniformity of concrete.
3. Assessing the quality of the concrete in relation to standard requirements.
4. Assessing the quality of one element of concrete in relation to another.
5.2. FOR PENETRATION TEST :- Penetration resistance tests on concrete offers a means of
determining relative strengths of concrete in the same structure or relative strength of different
structures.
5.3. FOR PULL-OUT TECHNIQUE :- The test measures the force required to pull out a
previously cast-in steel insert with an embedded enlarged end in the concrete which can be
related to the compressive strength of concrete.
5.4. FOR RESONANCE FREQUENCY METHOD :-
1. To determine the dynamic modulus of elasticity which provides an indication of the
mechanical integrity of structural components.
2. Resonant frequency methods provide an excellent means for studying the effects of
extreme temperature changes and loading
5.5. FOR MATURITY TEST :- The maturity function is presented to quantify the effects of
time and temperature. The measured time history could be used to compute a maturity index
which provides a reliable estimate of early age concrete strength as a function of time.
The resulting maturity factor is then used to determine the strength of concrete based on
established correlations.
5.6. FOR PERMEATION TEST :- To determine the permeability of concrete. The invasion of
aggressive substances into concrete is the main cause for concrete deterioration. Permeability
represents the governing property for estimating the durability of concrete structures.
19
5.7. FOR IMPACT-ECHO METHOD :- The impact-echo system involves the measuring of
concrete thickness and integrity using one surface. The test can be applied to determine the
location of cracking, voids, delamination and flaws in concrete.
5.8. FOR ULTRASONIC PULSE VELOCITY TEST :-
1. An ultrasonic pulse velocity test is an in-situ, non-destructive test to check the quality of
concrete and natural rocks.
2. In this test, the strength and quality of concrete or rock is assessed by measuring the
velocity of an ultrasonic pulse passing through a concrete structure or natural rock
formation.
5.9. FOR CORE CUTTER TEST :- The core samples can also be used for the following :-
1. Strength and density determination
2. Depth of carbonation of concrete
20
CHAPTER 6
Advances in sensors, development of new materials, and miniaturization of devices are all
paving the way for new NDT methods. Data fusion techniques are being developed to integrate
several NDT methods in the aim of enabling effective data-acquisition, processing, and
interpretation of test parameters in relation to material integrity. Much research interest and
industry attention have been devoted to acoustic techniques of NDT. This is a result of a clear
trend in testing concrete structures using acoustic signals processed by software using advanced
data analysis algorithms. NDT of concrete is increasingly gaining acceptance as a means of
evaluating material integrity. Low awareness regarding NDT methods is hindering its uptake and
is attributable to a lack of understanding construction materials and NDT methods themselves.
21
REFERENCES
1. IS: 13311 - 1992, Methods of non-destructive testing of concrete for all methods.
22