Beruflich Dokumente
Kultur Dokumente
15
LT-7000
LASER ALIGNMENT
DEVICE
IMS LT- 7000
INTRODUCTION:
The following instruction are to be used i n mounting the LT-7000 assembly for use i n the Exposcop 7000
C-Arm.
The addition of a few components incorporated i n the LT-7000 U2300 board assembly allows the
Exposcop 7000 laser device to power on and off from the C - A r m control panel. The system incorporates a
timer i n the C - A r m control w i t h a 1 m i n . preset on time.
CAUTION A N D WARNINGS :
T H E LT-7000 L A S E R P O S I T I O N I N G D E V I C E IS A C L A S S II L A S E R D E V I C E W H E N F U L L Y
ASSEMBLED H O W E V E R PLEASE OBSERVE THE FOLLOWING W H E N W O R K I N G A R O U N D
THE LASER ASSEMBLY.
CAUTION:
THE LT-7000 LASER ASSEMBLY INCORPORATES THE USE OF DIODE LASER MODULES WHICH
EMIT LASER RADIATION. THEREFORE DO NOT UNDER ANY CIRCUMSTANCES STARE , OR
VIEW DIRECTLY WITH OPTICAL INSTRUMENTS THE LASER BEAM OR ANY SCATTERED
LASER RADIATION DURING THE ASSEMBLY OR FINAL TESTING OF THE SYSTEM.
LASER: A T T E N T I O N — VISIBLE L A S E R L I G H T
CLASS H LASER PRODUCT
LASER RADIATION - D O N O T STARE
INTO B E A M
L A S E R C L A S S II, IEC 825, 21 C F R S U B C H A P T E R J , 1040
W h e n operating the laser light beam, the "Guidelines for the User IEC 825, M a i n Chapter 3"
have to be f o l l o w e d .
Observe all safety precautions when turning on power with covers removed from the
Observe all safety precautions when removing covers and installing electronic circuit
boards and cables. Static sensitive components are used on some of the components to
be installed.
Observe all Electrostatic discharge (ESD) precautions when handling circuit board
components and other electronic subassemblies.
Observe safety precautions when removing covers and reinstalling cover that you do not
drop or otherwise risk damage to the covers or surrounding components.
I N S T A L L A T I O N INSTRUCTIONS:
1) T u r n off all power to Exposcop 7000 and disconnect power cord from w a l l power outlet.
2 ) Remove Exposcop 7000 C - A r m generator cover then remove U45 board from generator board slot
connectors. See installation instruction diagrams page 6 for further details of removal of
generator cover.
3 ) U s i n g installation diagram page 7 locate and drill three (3) holes and mount connector X01 by
bending over the p i n connectors on the solder side of the board.
4 ) Solder jumper wire on solder side of U45 from P2 connector p i n 3 to X01 p i n 3 and glue to board
to secure i n place. See installation diagram page 8 and page 7.
5 ) Solder jumper wire on solder side of U45 from X I p i n 23 a,c to X01 p i n 2 and glue to the board to
secure i n place. See installation diagram page 8 and page 7.
6 ) Solder jumper wire on solder side of U45 from X I p i n 1 a,c to X01 p i n 1 and glue to the board to
secure i n place. See installation diagram page 8 and page 7.
7 ) Check to make sure all jumper wires are correctly installed and then reinstall U45 board i n the
generator.
8) Connect digital volt meter from p i n 1 of X01 (0V) to p i n 2 of X01 (+) connector on U45 board
making sure meter probes are not shorting at X01 connector.
9 ) Connect Power cord to wall outlet and turn on power to Exposcop 7000. Meter should read
+ 14.0 to 16.5 V D C .
10 ) T u r n off power and connect digital volt meter from p i n 1 of X01 (0V) to p i n 3 of X01 (+) connector
on U45 board making sure meter probes are not shorting at X01 connector.
12 ) If voltages i n step 9 and 11 are correct then turn off the power to the Exposcop Plus and remove
power cord from w a l l power outlet. If not determine cause of error by checking all connections,
then repeat steps 8 to 11.
P A R T 2 I N S T A L L A T I O N A N D A L I G N M E N T O F LT-7000 B O A R D A S S E M B L Y .
2 ) Place a small foam or plastic sheet on top of the end of the C - A r c to support and isolate the
U2300 board assembly and the install cable from X01 U45 board to X I of U2300 board m a k i n g
sure connectors are correctly positioned.
3 ) Connect power cord to wall outlet of Exposcop 7000 and then turn on power. After 40 sec or so the
Exposcop 7000 should be ready to test U2300 board.
4 ) Press the laser key o n the Exposcop 7000 control keyboard. The laser on L E D should light o n the
control keyboard as w e l l as the U2300 board power o n led's and laser's modules.
The lasers should come on for 1 minute then go off. The on time is preset by i n the software.
Pressing the laser key again w h e n the laser's are on should turn off the laser also.
F A I L U R E O F L A S E R P O W E R O N TEST.
If the laser fail to turn on you must determine the problem and repair as necessary. See
schematics for U2300 board and interface to Exposcop 7000 U45, U325 boards page 9.
5 ) After the power on test is found to be working correctly turn off power for Exposcop 7000 a n d
remove power cord form w a l l outlet.
6) Install the four 3" mounting standoff's b y removing only one screw at a time from the collimator
assembly i n order not to disrupt the collimator alignment. See installation diagrams page 11
for further details of U2300 board.
7) Once the stand offs are correctly installed then mount the U2300 board to the standoff's. T h e n
8) Connect power cord to wall outlet of Exposcop 7000 and then turn on power.
After 40 sec or so the Exposcop 7000 should be ready to test LT-7000 U2300 board.
9) Press the laser key on the Exposcop 7000 control keyboard. The laser on L E D should light on the
control keyboard as well as the U2300 board power on led's and laser's modules.
The lasers should come on for 1 minute then go off. The on time is set by the Z I E H M W I N SRV.
software. Pressing the laser key again w h e n the laser's are o n should turn off the laser also.
F A I L U R E O F L A S E R POWER O N TEST.
If the laser fail to turn on y o u must determine the problem and repair as necessary. See
schematics page 9 for U2300 board and interface to Exposcop 7000 U45 , U325 boards.
11) If the lasers turn on and off correctly and the alignment is complete, turn off the power to the
Exposcop 7000 and remove power cord from the w a l l outlet.
12 ) Install the filter cap w i t h laser w i n d o w s to the generator cover and reinstall generator cover.
13 ) Connect power cord to wall outlet of Exposcop 7000 and then turn on power. After 40 sec or so the
Exposcop 7000 should be ready to test laser and LI alignment. Check laser alignment if it is
still aligned then turn off the power to the Exposcop 7000 and remove power cord from the w a l l
outlet.
14 ) Once the alignment is complete secure generator cover and seal w i t h white silicon sealer.
This ends part two of the installation instructions for the LT-7000 laser assembly.
INTRODUCTION:
Several labels are required for identification and for certification of the laser device.
1) The following example and location guides must be used i n placement of the labels to complete
the installation of the laser device i n the Exposcop 7000.
2) Install Caution Label 40-511-L10, Aperture Label 40-513 & 40-514-L10, Small C a u t i o n Label
40-512-L10 to control desk and Laser Caution W h e n O p e n Label 40-515-L10 as shown i n the
following diagrams pages 5 -6.
3) F i l l out the Manufacture certification label 40-510-L10 and included all information. Serial
number, M o t h and Year must be typed. The month and year of manufacture shall be provided
clearly and legibly, without abbreviation, and w i t h the year s h o w n as a four- digit number.
The month must be spelled out. i.e., January, February, June, etc... D O N O T A B B R E V I A T E .
The certification and manufacture label must be installed on the generator cover just above the
C - A r c attachment to the generator and must be positioned i n the m i d d l e of this area. Then
apply a clear label cover over the label to protect the information.
THIS C O M P L E T E S T H E I N S T A L L A T I O N A S S E M B L Y A N D T E S T I N G
OF T H E U2300/LT-7000 L A S E R D E V I C E F O R E X P O S C O P 7000
Located on rear of
Generator cover
LASER
APERTURE
MANUFACTURED BY:
INTERNATIONAL MEDICAL SYSTEMS, INC
4181 L A T H A M STREET RIVERSIDE CA. 92501
MANUFACTURED:
MONTH: YEAR:.
• • •• • • •
c
• • • • • •
APERTURE
• • •
• • • • • •
• • • • 0 • •
• ••
• • •
o
C-Arm Control
APERTURE
C A U T I O N - Laser radiation
BOTTOM OF when open. D O N O T
TUBE HEAD ASSEMBLY ^jj^iTARE INTO B E A M
Laser Cap
RESEALWITH
WHITE SILICON
SEAL WHEN
REINSTALLING
COVER
The U45 Board modification for X01 connector provides power and O N / O F F control for the laser
positioning device.
Make sure the following connection are checked before power is turned on as i n correct placement of
wires can cause damage to both the C - A r m control and the laser device.
X01 P i n Configuration
3 ) A d d Three wire jumpers. Use small amount of glue to fix wires to board to prevent wires
from being damaged w h e n inserted into generator card rack
1) U45 P2 p i n 3 to X01 p i n 3
2) U45 X I p i n l a c to X01 p i n 1
3) U45 X 1 p i n 23ac to X01 p i n 2
3 ~
U45 J l U2300 J l
3 Conductors 9 " Spiral Wrap
1
10 "7 25 mm
The Exposcop 7000 U45 board provides the O N / O F F control and power for the U2300
Laser board through the interconnect cable.
Do not remove Switch Cam to file edge. Move ring assembly to allow
access to file edge of the Cam. Cover Tube head assembly parts to prevent
fillings from getting into tube assembly circuit boards and collimator.
Make sure no lose filings from the switch cam are left in the tube head
assembly.
See Example In
Dotted Lines
Small Caution
Laser Label CAUTION
Must be Attached LASER RADIATION-DO NOT
to Laser Board STARE INTO BEAM
LASER
4mm Alien Head Screws
APERTURE
Removed From The
Colimator Assembly
Small Laser
4mm Flat Washer Supplied With
Aperture Label
Laser Kit U45 Board
Must be Attached
LT-7000 / U2300 Power X01 Connector
Between Laser
Assembly Board
Module Assembly
Note: #40-514-L10
4mm X 3" Hex Stud
[Remove Only One Collimator
Assembly Screw And Replace With
Hex Stud At A Time To Prevent
Collimator Misalignment ]
Collimator
Assembly
Tilt Adjustment Tilt down The inside two screws should be tightened first to tilt
Screws the laser module inward toward the center of the
board. However be carefull not to adjust them to
much.
Laser Board
GRID SCREWS
INTRODUCTION:
The following instruction are to be used i n mounting the LT-7000 assembly for use i n the Exposcop 7000
C-Arm.
The addition of a few components incorporated i n the LT-7000 U2300 board assembly allows the
Exposcop 7000 laser device to power on and off from the C - A r m control panel. The system incorporates a
timer i n the C - A r m control w i t h a 1 m i n . preset on time.
CAUTION A N D WARNINGS :
T H E LT-7000 L A S E R P O S I T I O N I N G D E V I C E IS A C L A S S II L A S E R D E V I C E W H E N F U L L Y
ASSEMBLED H O W E V E R PLEASE OBSERVE THE F O L L O W I N G W H E N W O R K I N G A R O U N D
THE LASER ASSEMBLY.
CAUTION:
THE LT-7000 LASER ASSEMBLY INCORPORATES THE USE OF DIODE LASER MODULES WHICH
EMIT LASER RADIATION. THEREFORE DO NOT UNDER ANY CIRCUMSTANCES STARE , OR
VIEW DIRECTLY WITH OPTICAL INSTRUMENTS THE LASER BEAM OR ANY SCATTERED
LASER RADIATION DURING THE ASSEMBLY OR FINAL TESTING OF THE SYSTEM.
LASER: A T T E N T I O N — VISIBLE L A S E R L I G H T
CLASS n LASER PRODUCT
LASER RADIATION - D O N O T STARE
INTO B E A M
L A S E R C L A S S II, IEC 825, 21 C F R S U B C H A P T E R J , 1040
W h e n operating the laser light beam, the "Guidelines for the User IEC 825, M a i n Chapter 3"
have to be f o l l o w e d .
Observe all safety precautions when turning on power with covers removed from the
system. High voltage will be present at several locations.
Observe all safety precautions when removing covers and installing electronic circuit
boards and cables. Static sensitive components are used on some of the components to
be installed.
Observe all Electrostatic discharge (ESD) precautions when handling circuit board
components and other electronic subassemblies.
Observe safety precautions when removing covers and reinstalling cover that you do not
drop or otherwise risk damage to the covers or surrounding components.
1) M a k e sure power is turned off to Exposcop 7000 and w a l l outlet plug is disconnected.
2 ) Place a small foam or plastic sheet on top of the end of the C - A r c to support and isolate the
U2300 board assembly and the install cable from X4 of U45 board to X I of U2300 board making
sure connectors are correctly positioned.
3) Connect power cord to wall outlet of Exposcop 7000 and then turn on power. After 40 sec or so the
Exposcop 7000 should be ready to test U2300 board.
4 ) Press the laser key on the Exposcop 7000 control keyboard. The laser on L E D should light on the
control keyboard as w e l l as the U2300 board power on led's and laser's modules.
The lasers should come on for 1 minute then go off. The on time is preset by i n the software.
Pressing the laser key again w h e n the laser's are on should turn off the laser also.
5 ) After the power on test is found to be working correctly turn off power for Exposcop 7000 and
remove power cord form w a l l outlet.
6) Install the four 3" mounting standoff's by removing only one screw at a time from the collimator
assembly i n order not to disrupt the collimator alignment. See installation diagrams page 11
for further details of U2300 board.
7) Once the stand offs are correctly installed then mount the U2300 board to the standoff's. Then
Connect the cable from U45 X4, to X I of U2300 board.
8) Connect power cord to wall outlet of Exposcop 7000 and then turn on power.
After 40 sec or so the Exposcop 7000 should be ready to test LT-7000 U2300 board.
The lasers should come on for 1 minute then go off. The on time is set b y the Z I E H M W I N S R V .
software. Pressing the laser key again w h e n the laser's are on should turn off the laser also.
11) If the lasers turn o n and off correctly and the alignment is complete, turn off the power to the
Exposcop 7000 and remove power cord from the w a l l outlet.
12 ) Install the filter cap w i t h laser w i n d o w s to the generator cover and reinstall generator cover.
13 ) Connect power cord to wall outlet of Exposcop 7000 and then turn on power. After 40 sec or so the
Exposcop 7000 should be ready to test laser and I.I alignment. Check laser ah'gnment if it is
still aligned then turn off the power to the Exposcop 7000 and remove power cord from the w a l l
outlet.
14 ) Once the alignment is complete secure generator cover and seal w i t h white silicon sealer.
T h i s ends part two of the installation instructions for the LT-7000 laser assembly.
P A R T 3 L A B E L I N G E X P O S C O P 7000 W I T H L A S E R D E V I C E
INTRODUCTION:
Several labels are required for identification and for certification of the laser device.
1) The following example and location guides must be used i n placement of the labels to complete
the installation of the laser device i n the Exposcop 7000.
2 ) Install Caution Label 40-511-L10, Aperture Label 40-513 & 40-514-L10, Small C a u t i o n Label
40-512-L10 to control desk and Laser Caution W h e n Open Label 40-515-L10 as shown i n the
following diagrams pages 5 -6.
3) F i l l out the Manufacture certification label 40-510-L10 and included all information. Serial
number, M o t h and Year must be typed. The month and year of manufacture shall be p r o v i d e d
clearly and legibly, without abbreviation, and w i t h the year s h o w n as a four- digit number.
The month must be spelled out. i.e., January, February, June, etc... D O N O T A B B R E V I A T E .
The certification and manufacture label must be installed on the generator cover just above the
C - A r c attachment to the generator and must be positioned i n the m i d d l e of this area. Then
apply a clear label cover over the label to protect the information.
THIS C O M P L E T E S T H E I N S T A L L A T I O N A S S E M B L Y A N D T E S T I N G
O F T H E U2300/LT-7000 L A S E R D E V I C E F O R E X P O S C O P 7000
Located on rear of
Generator cover
m LASER RADIATION-DO NOT
STARE INTO BEAM
PEAK POWER
WAVELENGTH
lmW
635nm
CLASS I I LASER PRODUCT
LASER
APERTURE
MANUFACTURED BY:
INTERNATIONAL MEDICAL SYSTEMS, INC
4181 L A T H A M STREET RIVERSIDE CA. 92501
MANUFACTURED:
MONTH: YEAR:
^tASER^
APERTURE
\ /
T
i—/
C-Arm Control LASEFf^
APERTURE
C A U T I O N - Laser radiation
BOTTOM OF when open. D O N O T
TUBE HEAD ASSEMBLY ^ | | ^ T A R E INTO B E A M
RESEALWITH
WHITE SILICON
SEAL WHEN
REINSTALLING
COVER
U45 J l U2300 J l
1 0 " / 25 mm
The Exposcop 7000 U45 board provides the O N / O F F control and power for the U2300
Laser board through the interconnect cable.
Do not remove Switch Cam to file edge. Move ring assembly to allow
access to file edge of the Cam. Cover Tube head assembly parts to prevent
fillings from getting into tube assembly circuit boards and collimator.
Make sure no lose filings from the switch cam are left in the tube head
assembly.
See Example In
Dotted Lines
LASER
4mm Allen Head Screws
APERTURE
Removed From The
Colimator Assembly
Small Laser
4mm Flat Washer Supplied With
Aperture Label
Laser Kit U45 Board
Must be Attached
LT-7000 / U2300 Power X01 Connector
Between Laser
Assembly Board
Module Assembly
Note: #40-514-L10
4mm X 3" Hex Stud
[Remove Only One Collimator
Assembly Screw And Replace With
Hex Stua At A Time To Prevent
Collimator Misalignment ]
Collimator
Assembly