Beruflich Dokumente
Kultur Dokumente
This certifies that the above instrument was calibrated in compliance with Techmaster de Mexico's Calibration Systems
Requirement in accordance with referenced procedures. Standards used to perform this calibration are traceable to SI units;
their source of traceability derives from a National Metrology Institute such as NIST, CENAM, NPL, DIN, from natural
physical constants, consensus standards or derived by the ratio type of calibrations. Collective uncertainties are determined
as required with a distribution that corresponds to a probability of approximately 95% (k=2). Uncertainties are not taken
into account in determining In-Tolerance results. All calibrations are performed to manufacturer's specifications unless
otherwise noted.
This form shall not be reproduced, except in full, without the expressed written consent of Techmaster de Mexico SA de CV
Condition Returned: Calibrated With Data per Customer Contract Calibration Cycle: 3 Months
Returned within specifications?: YES Calibration Date: Mar/25/2019
Temperature: 25ºC Relative Humidity: 44% Next Due Date: Jun/25/2019
Calibrated On Site? No Technician: Gerardo Orduño Beltrán
G. Orduño
Ernesto Matamoros Ing. Mauricio Garayzar Gerardo Orduño Beltrán
Quality Assurance Technical Manager Approved By
Tijuana, B.C. Calle Seminario No. 8610-11, Col. Niños Héroes Este, CP 22120, Tijuana, BC, México Tels.: (664) 624-4444 / 624-3128 / 624-4445 / 624-0440
Mexicali, B.C. Calle Gales Nº 1201, Col. Villa Fontana, C.P. 21180, Mexicali, BC, México Tels.:(686) 555-1660 / 557-6117 / 555-1766
Cd. Juárez,Chih. Blvd. Gomez Morin No.9050-L8, Col. Partido Senecu, CP. 32469, CD. Juarez, Chih. México. Tels.:(656) 687-2471 / 648-1181
Monterrey, N.L. Ave. Morones Prieto No. 914, Oriente Int. 112, Col. La Huerta, C.P. 67144. Tels.:(81)1334-0701 / 1334-0702
540.1 1901
Page 1 of 2
3
TME-0-22140798-R1 20
20
Calibration Results
Manufacturer: Atago Asset No. GAM008195
Step # Function Tested / Nominal Value As Found ± MU* In Tol As Left ± MU* In Tol Calibration Tolerance
1 BRIX % 0 % 0 ± N/A YES 0 ± N/A YES 0 to 0 %
2 5.0 % 5.0 ± N/A YES 5.0 ± N/A YES 4.8 to 5.2 %
3 9.8 % 9.7 ± N/A YES 9.7 ± N/A YES 9.6 to 10.0 %
4 15.8 % 15.7 ± N/A YES 15.7 ± N/A YES 15.6 to 16.0 %
5 21.8 % 21.7 ± N/A YES 21.7 ± N/A YES 21.6 to 22.0 %
6 25.5 % 25.4 ± N/A YES 25.4 ± N/A YES 25.3 to 25.7 %
7 Temperature 25.0 °C 24.800 ± 0.068 YES 24.800 ± 0.068 YES 24.0 to 26.0 °C
*********************************End of Report***********************************
Calibracion apegado al standard AMS2770 seccion 3.4.9.3.6 Metodo B por requerimiento del cliente
Manufacturer Spec
540.6 1503
Page 2 of 2
3
TME-0-22140798-R1 20
20
Curva de Calibración
Brix (%)
Concentración ( g)
0 0
4.99 5
9.99 9.8 Pendiente = 0.8441
16.99 15.8 Intersección = 0.7467
25.00 21.8 Coeficiente de correlación = 0.9963
30.00 25.5
Curva de Calibración
f(x) = 0.8441907151x + 0.7467889174
R² = 0.9963311448
Medición Brix %
Concentración Sacarosa
Page 3 of 3
TME-0-22140798-R1 20