Beruflich Dokumente
Kultur Dokumente
Autoranging Function
Red+ Black- The Autoranging function automatically selects the optimum measurement 1. Set the function selector to Ω.
Test Leads range. 2. Connect the test leads to the object to be measured, and read the display.
The AUTO indicator appears during Autoranging. Red+ Press the RANGE button to select the range manually.
The range automatically switches up when the display shows 2800 to 3249 Black- To re-enable Autoranging, hold RANGE for one seconds.
counts or more, and down when the display shows 269 counts or less. (3.2
Function V (AUTO/ / ), mV (AUTO/ / ): Auto Voltage/DC/AC
kΩ range: 259 counts) Continuity Checking ( )
Selector Ω: Resistance
: Continuity/Diode Check The Autoranging function is not available in the millivolt (mV) range, or in
OFF: Power Off the Continuity or Diode Check functions. Voltage Measurement (V) DANGER
Disabling Autoranging Never apply voltage to the test leads when the Continuity Check
SHIFT Button For the Voltage (V, mV) function: switches between Press RANGE to switch to Manual Ranging (the AUTO indicator
DANGER function is selected. Doing so could damage the instrument and
Auto Voltage, AC and DC The maximum rated voltage is 600 V DC/AC rms (sine wave), or injure the user.
disappears)
Switches between Continuity and Diode Check 107 V Hz. Attempting to measure voltage in excess of the
The measurement range can then be selected by the RANGE button. To avoid electric shock, remove power from the circuit under test
functions maximum rated voltage could destroy the instrument and injure or
Enabling Autoranging before measuring.
Starts and cancels the Auto-Hold function (refer to the kill the user.
Auto-Hold function description) Hold RANGE for 1 seconds.
Cancels the Auto Power Save function (refer to "Auto Do not connect the test leads while voltage is present: a short
Power Save") Auto-Hold Function circuit could result and cause injury. Pay careful attention when
コネクタのつまみ making measurements.
RANGE Button Selects between Manual and Autoranging switching This function displays and holds either the maximum voltage or minimum
resistance measurement. For safety, test lead connections must always be made at the
(refer to "Autoranging Function") Black-
コネクタのつまみ
Hold the SHIFT button for one second to enable Auto-Hold (a beep sounds secondary side of a circuit breaker.
Selects the range during Manual Range operation
and the HOLD indicator appears). The maximum rated voltage between input terminals and ground
LCD (Display) . :
Decimal point
To cancel Auto-Hold: is 600 V AC/DC rms (sine wave). Attempting to measure voltages
:
Indicates DC voltage function exceeding 600 V with respect to ground could damage the
:
Indicates AC voltage function Hold the SHIFT button again for one second (a beep sounds and HOLD Red+
indicator disappears). instrument and injure the user.
:
Indicates continuity during Continuity Check
function When measuring voltage, the display remains unchanged as long as the
: Indicates Diode Check function measured value is within the dead zone (the indicator blinks). AC Voltage
AUTO : Indicates Autoranging, or Auto Voltage When the measured voltage reaches or exceeds the dead zone, the new Measurement 1. Set the function selector to (the , Ω indicator appear).
function when blinking value is displayed and a beep sounds, after which the display remains 2. Connect the test leads to the object to be measured. Resistance is
APS : Indicates Auto Power Save is enabled unchanged until another measured value exceeds the displayed value (the displayed when checking continuity コネクタのつまみ
(320 Ω range).
: Indicates low battery voltage (1.2 0.1 V) HOLD indicator appears). 3. When the circuit is closed (250 Ω or less), the indicator appears and a
mV,V : Voltage and diode check units Dead zone: 270 counts in 3.2 V range, 30 counts in all other ranges. beep sounds.
Ω,kΩ
Ω,MΩ
Ω : Resistance and continuity check units When measuring resistance, the display remains unchanged as long as the Black- Red+
HOLD : Lights when the Auto-Hold function is enabled measured value is "OF" [overflow] (the HOLD indicator blinks). Diode Checking ( )
+Terminal This instrument is a two-terminal design, so test lead When a measurable resistance is present, the value is displayed and a DC Voltage
beep sounds, after which the display remains unchanged until another
DANGER
connections do not need to be changed when changing Measurement
functions. Connect the RED lead here. measured value is less than the displayed value (the HOLD indicator Never apply voltage to the test leads when the Diode Check
lights). 1. Set the function selector to V or mV (if AUTO is blinking, the Auto Voltage function is selected. Doing so could damage the instrument and
COM Terminal This is the common terminal for all functions. Connect injure the user.
the BLACK lead here. function will select AC or DC automatically).
Auto Power Save Function 2. Connect the test leads to the measurement object, and read the display. To avoid electric shock, remove power from the circuit under test
Safety Cap The safety cap minimizes the amount of exposed metal This function activates the power save state 30 minutes after the last To select between Auto Voltage, AC and DC volts, press the SHIFT button. before measuring.
at the probe tip, but the probe can also be used without
operation. In the power save state, the LCD is blanked, but power is not Press the RANGE button to select the range manually.
the cap.
completely turned off. Hold RANGE for one seconds to re-enable Autoranging (AUTO appears).
Auto Power Save is automatically enabled when the instrument is turned on
(the APS indicator appears).
Other Functions Exiting the Power Save State
コネクタのつまみ
Cathode Anode
Auto Voltage Function Either turn the Function selector, or press SHIFT or RANGE.
This function automatically selects the voltage range according to the All selections are reset when exiting the Power Save State, so stored data Black- Red+
voltage being measured, and automatically selects DC or AC voltage is invalid. For long-term operation, disable Auto Power Save beforehand.
measurement. Disabling Auto Power Saving
Setting the function selector to V or mV enables the Auto Voltage function Hold the SHIFT button down while turning the instrument on, and keep
(the AUTO indicator appears blinking). holding it (for about two seconds) until a beep sounds.
When the V function is selected, measurement of DC voltage ( ) begins. The APS indicator is not displayed, and Auto Power Saving is disabled until
Automatic switching from DC to AC occurs at a preset threshold in the the instrument is turned off.
range of two to ten volts (at 50 Hz) AC. If the measured AC voltage 1. Set the function selector to andコネクタのつまみ
press the SHIFT button
コネクタのつまみ
exceeds this threshold, the instrument switches to AC Voltage function. If (the indicator appears).
the measured AC voltage drops below about 1 V on the display, the 2. Connect the red test lead to the diode's anode, and the black test lead to
instrument switches back to DC Voltage function. The actual voltage level the cathode.
at which the AC voltage function switches to DC is frequency dependent, The display shows forward voltage (0.4 to 0.7 V) for a normal diode. In the
and is approximately equal to [frequency/5] volts, or less. opposite polarity, the open-terminal voltage (1.7 V or less) is displayed.
When the mV function is selected, measurement of DC voltage ( ) begins. The display shows about 0 V if the diode is shorted, and the open-terminal
Automatic switching from DC to AC occurs at a preset threshold in the voltage in both directions (3.2 V range) if the diode is open.