Sie sind auf Seite 1von 68

DESIGN OF HVAC

SYSTEM

1 of 68
CONTENTS:

DESCRIPTION
* Scope
* Applicable Codes, Standard and Reference Document
* Design Parameter
* Co-efficient Transmission (U-value) for Roof, wall, partition and floor
* Internal load details
* HVAC Data Gathering sheet
* Ventilation, Exhaust and Pressurization
* Computer Generated Heating and Cooling load calculation
* Equipment selection
* Equipment Data Schedule
* Sequence of Operation
* Computerized Duct sizing calculation
* Heater Sizing
* Battery room and Toilet exhaust fan sizing
* Sizing of sand trap louver & fresh air filter
* Air Balancing and Air Diffusion system

2 of 68
1 SCOPE:

The scope of work includes Designing, Engineering, Procurement of Material,


Manufacturing, Delivery, Installation, Testing and Commissioning of the HVAC
System for the building of‫؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟‬. The scope of work is limited to the
scope of work mentioned in the Clause No‫؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟‬

Scope of work includes the provision of HVAC system for the following building
(Zones):
1 BATTARY ROOM
2 STORE ROOM
3 FIRE FIGHTING ROOM
4 AC/DC ROOM
5 TELECOM
6 PASSAGE
7 CONTROL ROOM
8 OFFICE
9 TOILET
10 KITCHEN
11 33KV SWGR ROOM
12 BASEMENT

2 APPLICABLE CODES,
CODES STANISCOSAD AND REFERENCE DOCUMENT:

2.1 ARI-210 : Unitary Air conditioning Equipment.


2.2 ARI-360 : Commercial and industrial Air Conditioning Equipment.
2.3 ARI-410 : Forced Air Circulation and Air Heating Equipment.
2.4 ARI-365 : Condensing unit.
2.5 ARI-430 : Central Station air handling unit.
2.6 NFPA-70: Terminal Lugs.
2.7 ANSI/ASME B16.22 : Fittings
2.8 NEEMA-MG1 : For Motors.
2.9 ASHRAE hand book of HVAC Fundamental - 1977.
2.10 Principle of HVAC by ASHRAE.
2.11 SMACNA for Duct works.
2.12 73-TMSS-1, REV-4, SEC-EOA Material Standard Specification for Air
Conditioning Units.
2.13 TES-K-100, Rev-2, SEC-EOA Engineering Standard for HVAC System

3 of 68
3 DESIGN PARAMETER:

3.1 SITE CONDITION (Ref. TES-K-100 Table 1.0 & 2.0)

3.1.1 Site Location ‫؟؟؟؟؟؟؟؟‬


3.1.2 Site Elevation 2200 M. Above mean sea level
'o
3.1.3 Site Latitude 18 25' North

3.2 DESIGN CONDITION


Out Door Temperature during summer
o
3.2.1 Design ambient Dry bulb temperature 39 C 102 oF
o
3.2.2 Design ambient Wet bulb temperature 17.2 C 63 oF
o
3.2.3 Daily Range 13.9 C 25 oF
Design Month and Time August (4 p.m)

Out Door Temperature during winter


o
3.2.3 Design ambient Dry bulb temperature 3.9 C 39 oF
3.2.4 Noise level @2M distance in open area 60 dB(A)

3.3 Indoor Conditions:


o
3.3.1 Design temperature 25 C 77 oF
3.3.2 Relative humidity 50 %RH
3.3.3 Equipment operation 24 Hours
3.3.4 Noise level 45 dB(A)
O
3.4 Prevailing wind direction 15 NW
3.5 Maximum wind speed 24 KMPH (15MPH)
3.6 Over Pressurization 0.2 in of W.G.

Note:- Indoor design Temperature


a) 25 oC

4 of 68
4 CO-EFFICIENT OF TRANSMISSION (U-VALUE) FOR ROOF, WALL, DOOR
PARTITION AND FLOOR:
The resistance values are taken from ASHRAE Fundamentals 1997 table # 1, 4 ,
unless other wise mentioned.

4.1 Coefficient of Transmission (U) for roof without false ceiling


Material R-Value Ref. Document
Construction Detail Material Specification o 2
Thickness F-FT -Hr/BTU ASHRAE Table
1.Outside air film - Moving 15 mph 0.17 ASHRAE, Table - 1
2.Tiles 30mm 0.06 ASHRAE, Table - 4
1 2 3 4 3.Separation Layer 200 microns Negligible

4. Extruded rigid polystyrene 50mm 7.7 ISO BOARD ND


insulation
5. Elastomeric sheet water 1.5mm Negligible
proofing membrane(pvc)
6.LW concrete 50mm 0.38
6. Concrete Slab 150mm 0.60 ASHRAE, Table - 4
5 6 7 7. Inside still air 0.92 ASHRAE, Table - 1
TOTAL OF R-VALUE 9.83
U-FACTOR = 1/R 0.102 Btu/Hr-FT2-oF

4.2 Coefficient of Transmission for roof with false ceiling


Material R-Value Ref. Document
Construction Detail Material Specification o 2
Thickness F-FT -Hr/BTU ASHRAE Table
1.Outside air film - Moving 15 mph 0.17 ASHRAE, Table - 1
2.Tiles 30mm 0.06 ASHRAE, Table - 4
1 2 3 4 3.Separation Layer 200 microns Negligible

4. Extruded rigid polystyrene 50mm 7.7 ISO BOARD ND


insulation
5. Elastomeric sheet water 1.5mm Negligible
proofing membrane(pvc)
6.LW concrete 50mm 0.38
6. Concrete Slab 150mm 0.60 ASHRAE, Table - 4
7. Acoustic Tile 20mm 1.34 From Arabian Fibre Gl. Cat.
5 8 6 7 8. Inside still air 0.92 ASHRAE, Table - 1
TOTAL OF R-VALUE 11.17
U-FACTOR = 1/R 0.090 Btu/Hr-FT2-oF

5 of 68
5 INTERNAL LOAD DATA:

Internal loads involve components of cooling loads which arises from sources internal to the

conditioned space. The following components shall be dealt with in the proceeding items :

5.1 LIGHTING :
The details of the lighting loads in each room is taken from actual lighting load calculation.
The Summary of lighting load is enclosed for reference.

Formula
Qs = 3.41 x qw x Fu x Fs x CLF

Where :
Qs = Sensible cooling load in BTU/Hr.

qw = Total Lamp Wattage (As shown in the detailed calculation enclosed)

Fu = Usage factor (%)


= Wattage in use x 100
Total Installed Wattage

Fs = Special Balast allowance refer to Table 4.1 ASHRAE GRP-158


= Use 1.20

CLF = 1, Since lights will be turned on more than 16 Hrs. per day.

Summary of lighting load is as below:

Zone Name Lighting load


in Watts
BATTARY ROOM 835
STORE ROOM 1037
FIRE FIGHTING ROOM 1037
AC/DC ROOM 1382
TELECOM 1382
PASSAGE 518
CONTROL ROOM 5184
OFFICE 1037
TOILET 96
KITCHEN 86
33KV SWGR ROOM 1814
BASEMENT 1037
TOTAL 15446

6 of 68
5.3 EQUIPMENT HEAT GAIN :

The heat gain are due to the heat dissipated by equipment's inside the building.
The actual load dissipation from the each panel is taken from the each equipment
manufacturer & as summarized by the Electrical Engineer.

The summery of equipment load are as below:

Zone Name Equipment load


in Watts
BATTARY ROOM 1,170
STORE ROOM -
FIRE FIGHTING ROOM 500
AC/DC ROOM 4,800
TELECOM 1,000
PASSAGE -
CONTROL ROOM 4,120
OFFICE 200
TOILET -
KITCHEN 500
33KV SWGR ROOM 26400
BASEMENT 15000
TOTAL 53,690

7 of 68
Wall Partition Light. Equip. Nos. of
People
SE SW NW NE Wall Watts Watts
Avg. Height of wall : 5.9 m Avg. Height of wall : 8.95 m
Width of the wall :27.5 m Width of the wall 12.5 m
Area =5.9 M x27.5 M Area =8.95 M x12.5 M
2
162.25 M 111.88 M2
2
1746.62 Ft 1204.33 Ft2
835 1170 -

Avg. Height of wall : M 5 Avg. Height of wall : 5m


Width of the wall : M 6 Width of the wall : 32.2 m
Area =4.6 M x 6.005 M Area =5 M x 32.2 M
1 2
30.03 M 161.00 M
1 2
323.22 Ft 1733.17 Ft
1037 - 1

Avg. Height of wall : 4.18m


Width of the wall : 5.9 m
Area =4.18 M x 5.9 M
2
24.66 M
2
265 49 Ft
265.49
1037 500 1

8 of 68
Wall Partition Light. Equip. Nos. of
People
SE SW NW NE Wall Watts Watts
Avg. Height of wall : 4.27m - -
Width of the wall : 8.3m
Area = 8.3 M x4.27 M
2
35.44 M
2
381.52 Ft
1382 4800 1

4 x1.5

area=6 M2

86 500 1

Avg. Height of wall : 5.2m Avg. Height of wall : 5.2m Avg. Height of wall : 5.2m 5.4 x .8
Width of the wall 4.64 m Width of the wall :3.5 m Width of the wall 4.64 m
Area =5.2M X4.64m Area =5.2M X3.5m Area =5.2M X4.64m area=4.3 M2
2 2 2
24.13 M 18.20 M 24.13 M
2 2 2
259.74 Ft 195.92 Ft 259.74 Ft
1814 26400 1

- 47 x 2.23

area=104.8 M2

1037 15000 -

9 of 68
132/33KV SUBSTATION
HVAC Load Analysis
for

Prepared By:

10 of 68
Chvac - Full Commercial HVAC Loads Calculation Program Elite Software Development, Inc.
132/33KV SUBSTATION

General Project Data Input


General Project Information
Project file name:
Substation_rev_lighting.CHV
Project title:
Project address:
Project city, state, ZIP:
Designed by:
Project date: /
Project comment:
Weather reference city:
Client name:
MAS
Company name:
Company representative:
Company address:
Barometric pressure: 22.900 in.Hg.
Altitude: 7216 feet
Latitude: 18 Degrees
Mean daily temperature range: 25 Degrees
Starting & ending time for HVAC load calculations: 1am - 12am
Number of unique zones in this project: 12

Building Default Values


Calculations performed: Both heating and cooling loads
Lighting requirements: 0.00 Watts per square foot
Equipment requirements: 0.00 Watts per square foot
People sensible load multiplier: 315 Btuh per person
People latent load multiplier: 325 Btuh per person
Zone sensible safety factor: 10 %
Zone latent safety factor: 10 %
Zone heating safety factor: 10 %
People diversity factor: 100 %
Lighting profile number: 2
Equipment profile number: 3
People profile number: 1
Building default ceiling height: 0.00 feet
Building default wall height: 0.00 feet

Internal Operating Load Profiles (C = 100)


hr hr hr hr hr hr hr hr hr hr hr hr hr hr hr hr hr hr hr hr hr hr hr hr
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
1 C C C C C C C C C C C C C C C C C C C C C C C C
2 C C C C C C C C C C C C C C C C C C C C C C C C
3 C C C C C C C C C C C C C C C C C C C C C C C C
4 C C C C C C C C C C C C C C C C C C C C C C C C
5 C C C C C C C C C C C C C C C C C C C C C C C C
6 C C C C C C C C C C C C C C C C C C C C C C C C
7 C C C C C C C C C C C C C C C C C C C C C C C C
8 C C C C C C C C C C C C C C C C C C C C C C C C
9 C C C C C C C C C C C C C C C C C C C C C C C C
10 C C C C C C C C C C C C C C C C C C C C C C C C

11 of 68
C:\disc top 6.032_33kv Substation_rev_lighting.CHV Wednesday, February 11, 2009, 10:54 PM
Chvac - Full Commercial HVAC Loads Calculation Program Elite Software Development, Inc.
Page 3

General Project Data Input (cont'd)


Building-Level Design Conditions
Design Outdoor Outdoor Indoor Indoor Grains In/Outdoor
Month Dry Bulb Wet Bulb Rel.Hum Dry Bulb Diff Correction
August 102 63 50% 77 -40.31 6
Winter 39 75

Master Roofs
Roof ASHRAE Roof Dark Susp.
No. Roof# U-Fac Color Ceil
1 12 0.090 No Yes
2 12 0.102 No No

Master Walls
Wall ASHRAE Wall Wall
No. Group U-Fac Color
1 G 0.250 M
2 A 0.105 M
3 A 0.300 M

Master Partitions
Partition Partition Cool Heat
No. U-Factor T-D T-D
1 0.250 8 10
2 0.133 8 12
3 0.300 3 10

12 of 68
C:\disc top 6. 132_33kv Substation_rev_lighting.CHV Wednesday, February 11, 2009, 10:54 PM
Chvac - Full Commercial HVAC Loads Calculati
AH 132/33KV SUBSTATION
Page 4

Zone Input
Zone 1: Battery Room (377.6592 sq.ft) (Group 0)
Air Handler number: 1 Zone occurrences: 1
Zone length: (feet) 19.68 Zone width (feet): 19.19
Lighting Watts: 835 Equipment Watts: 1,170
Number of people in zone: 0 People profile number: 1
Lighting profile number: 2 Equipment profile number: 3
Ceiling height (feet): 16.70 Heating safety factor (%): 10
Sensible safety factor (%): 10 Latent safety factor (%): 10
Sensible heat per person (Btuh): 315 Latent heat per person (Btuh): 325
Cooling ventilation method: Direct Cooling ventilation value: 1,350.000
Cooling infiltration method: Direct Cooling infiltration value: 0.000
Heating ventilation method: Direct Heating ventilation value: 1,350.000
Heating infiltration method: Direct Heating infiltration value: 0.000
Winter exhaust air CFM: 1,350 Summer exhaust air CFM: 1,350
Minimum supply CFM: 1,350 Latent Btuh equipment load: 0
Ceil. exposed to plenum (sq.ft): 0 Exposed floor slab perimeter (ft): 78
Both heating and cooling loads are calculated for this zone.

Roof Type ASHRAE# U-Factor Dark Length Width Area Susp.Ceil


1 2 12 0.102 No 19.68 19.19 377.7 No

Wall Type ASHRAE# U-Factor Color Height Width Area Direction


1 2 A 0.105 M 16.70 19.68 328.7 SW
2 2 A 0.105 M 16.70 19.19 320.5 SE

Zone 2: Store Room (377.6592 sq.ft) (Group 0)


Air Handler number: 1 Zone occurrences: 1
Zone length: (feet) 19.68 Zone width (feet): 19.19
Lighting Watts: 1,037 Equipment Watts: 0
Number of people in zone: 1 People profile number: 1
Lighting profile number: 2 Equipment profile number: 3
Ceiling height (feet): 16.70 Heating safety factor (%): 10
Sensible safety factor (%): 10 Latent safety factor (%): 10
Sensible heat per person (Btuh): 315 Latent heat per person (Btuh): 325
Cooling ventilation method: Direct Cooling ventilation value: 37.000
Cooling infiltration method: Direct Cooling infiltration value: 0.000
Heating ventilation method: Direct Heating ventilation value: 37.000
Heating infiltration method: Direct Heating infiltration value: 0.000
Winter exhaust air CFM: 0 Summer exhaust air CFM: 0
Minimum supply CFM: 0 Latent Btuh equipment load: 0
Ceil. exposed to plenum (sq.ft): 0 Exposed floor slab perimeter (ft): 78
Both heating and cooling loads are calculated for this zone.

Roof Type ASHRAE# U-Factor Dark Length Width Area Susp.Ceil


1 2 12 0.102 No 19.68 19.19 377.7 No

Wall Type ASHRAE# U-Factor Color Height Width Area Direction


1 2 A 0.105 M 16.70 19.19 320.5 NE
2 2 A 0.105 M 16.70 19.68 328.7 SE

Zone 3: Fire Fighting (377.6592 sq.ft) (Group 0)


Air Handler number: 1 Zone occurrences: 1
Zone length: (feet) 19.68 Zone width (feet): 19.19
Lighting Watts: 1,037 Equipment Watts: 500
Number of people in zone: 1 People profile number: 1
13 of 68
Wednesday, February 11, 2009, 10:54 PM
Chvac - Full Commercial HVAC Loads Calcula
Page 5

Zone Input (cont'd)


Zone 3: Fire Fighting (377.6592 sq.ft) (Group 0)
Lighting profile number: 2 Equipment profile number: 3
Ceiling height (feet): 16.70 Heating safety factor (%): 10
Sensible safety factor (%): 10 Latent safety factor (%): 10
Sensible heat per person (Btuh): 315 Latent heat per person (Btuh): 325
Cooling ventilation method: Direct Cooling ventilation value: 1,125.000
Cooling infiltration method: Direct Cooling infiltration value: 0.000
Heating ventilation method: Direct Heating ventilation value: 1,125.000
Heating infiltration method: Direct Heating infiltration value: 0.000
Winter exhaust air CFM: 1,125 Summer exhaust air CFM: 1,125
Minimum supply CFM: 1,125 Latent Btuh equipment load: 0
Ceil. exposed to plenum (sq.ft): 0 Exposed floor slab perimeter (ft): 8
Both heating and cooling loads are calculated for this zone.

Roof Type ASHRAE# U-Factor Dark Length Width Area Susp.Ceil


1 2 12 0.102 No 19.68 19.19 377.7 No

Wall Type ASHRAE# U-Factor Color Height Width Area Direction


1 2 A 0.105 M 16.70 19.19 320.5 SE

Zone 4: Ac/dc Room (352.4924 sq.ft) (Group 0)


Air Handler number: 1 Zone occurrences: 1
Zone length: (feet) 25.58 Zone width (feet): 13.78
Lighting Watts: 1,382 Equipment Watts: 4,800
Number of people in zone: 1 People profile number: 1
Lighting profile number: 2 Equipment profile number: 3
Ceiling height (feet): 13.12 Heating safety factor (%): 10
Sensible safety factor (%): 10 Latent safety factor (%): 10
Sensible heat per person (Btuh): 315 Latent heat per person (Btuh): 325
Cooling ventilation method: Direct Cooling ventilation value: 86.000
Cooling infiltration method: Direct Cooling infiltration value: 0.000
Heating ventilation method: Direct Heating ventilation value: 86.000
Heating infiltration method: Direct Heating infiltration value: 0.000
Winter exhaust air CFM: 0 Summer exhaust air CFM: 0
Minimum supply CFM: 0 Latent Btuh equipment load: 0
Ceil. exposed to plenum (sq.ft): 352 Exposed floor slab perimeter (ft): 81
Both heating and cooling loads are calculated for this zone.

Wall Type ASHRAE# U-Factor Color Height Width Area Direction


1 2 A 0.105 M 13.12 25.58 335.6 SW

Zone 5: Telecom (401.606 sq.ft) (Group 0)


Air Handler number: 1 Zone occurrences: 1
Zone length: (feet) 25.58 Zone width (feet): 15.70
Lighting Watts: 1,382 Equipment Watts: 1,000
Number of people in zone: 2 People profile number: 1
Lighting profile number: 2 Equipment profile number: 3
Ceiling height (feet): 13.12 Heating safety factor (%): 10
Sensible safety factor (%): 10 Latent safety factor (%): 10
Sensible heat per person (Btuh): 315 Latent heat per person (Btuh): 325
Cooling ventilation method: Direct Cooling ventilation value: 23.000
Cooling infiltration method: Direct Cooling infiltration value: 0.000
Heating ventilation method: Direct Heating ventilation value: 23.000
Heating infiltration method: Direct Heating infiltration value: 0.000
Winter exhaust air CFM: 0 Summer exhaust air CFM: 0
Minimum supply CFM: 0 Latent Btuh equipment load: 0
14 of 68
C:\disc to 132_33kv Substation_rev_lighting.CHV Wednesday, February 11, 2009, 10:54 PM
Chvac - Full Commercial HVAC Loads Calculation Program Elite Software Development, Inc.
A
Page 6

Zone Input (cont'd)


Zone 5: Telecom (401.606 sq.ft) (Group 0)
Ceil. exposed to plenum (sq.ft): 402 Exposed floor slab perimeter (ft): 80
Both heating and cooling loads are calculated for this zone.

Zone 6: Passage (280.7 sq.ft) (Group 0)


Air Handler number: 1 Zone occurrences: 1
Zone length: (feet) 280.70 Zone width (feet): 1.00
Lighting Watts: 518 Equipment Watts: 0
Number of people in zone: 0 People profile number: 1
Lighting profile number: 2 Equipment profile number: 3
Ceiling height (feet): 13.12 Heating safety factor (%): 10
Sensible safety factor (%): 10 Latent safety factor (%): 10
Sensible heat per person (Btuh): 315 Latent heat per person (Btuh): 325
Cooling ventilation method: Direct Cooling ventilation value: 11.000
Cooling infiltration method: Direct Cooling infiltration value: 0.000
Heating ventilation method: Direct Heating ventilation value: 11.000
Heating infiltration method: Direct Heating infiltration value: 0.000
Winter exhaust air CFM: 0 Summer exhaust air CFM: 0
Minimum supply CFM: 0 Latent Btuh equipment load: 0
Ceil. exposed to plenum (sq.ft): 281 Exposed floor slab perimeter (ft): 100
Both heating and cooling loads are calculated for this zone.

Wall Type ASHRAE# U-Factor Color Height Width Area Direction


1 2 A 0.105 M 13.12 8.30 108.9 SW

Zone 7: Control And Protection Room (1434.196 sq.ft) (Group 0)


Air Handler number: 1 Zone occurrences: 1
Zone length: (feet) 50.84 Zone width (feet): 28.21
Lighting Watts: 5,184 Equipment Watts: 4,120
Number of people in zone: 3 People profile number: 1
Lighting profile number: 2 Equipment profile number: 3
Ceiling height (feet): 13.12 Heating safety factor (%): 10
Sensible safety factor (%): 10 Latent safety factor (%): 10
Sensible heat per person (Btuh): 315 Latent heat per person (Btuh): 325
Cooling ventilation method: Direct Cooling ventilation value: 93.000
Cooling infiltration method: Direct Cooling infiltration value: 0.000
Heating ventilation method: Direct Heating ventilation value: 93.000
Heating infiltration method: Direct Heating infiltration value: 0.000
Winter exhaust air CFM: 0 Summer exhaust air CFM: 0
Minimum supply CFM: 0 Latent Btuh equipment load: 0
Ceil. exposed to plenum (sq.ft): 1,434 Exposed floor slab perimeter (ft): 158
Both heating and cooling loads are calculated for this zone.

Wall Type ASHRAE# U-Factor Color Height Width Area Direction


1 2 A 0.105 M 13.12 50.84 667.0 NE

Zone 8: Office (232.842 sq.ft) (Group 0)


Air Handler number: 1 Zone occurrences: 1
Zone length: (feet) 15.42 Zone width (feet): 15.10
Lighting Watts: 1,037 Equipment Watts: 200
Number of people in zone: 1 People profile number: 1
Lighting profile number: 2 Equipment profile number: 3
Ceiling height (feet): 13.12 Heating safety factor (%): 10
Sensible safety factor (%): 10 Latent safety factor (%): 10
Sensible heat per person (Btuh): 315 Latent heat per person (Btuh): 325
Coolin
15 of 68
132_33kv Substation_rev_lighting.CHV Wednesday, February 11, 2009, 10:54 PM
Chvac - Full Commercial HVAC Loads Calculation Program Elite Software Development, Inc.
132/33KV SUBSTATION
Page 7

Zone Input (cont'd)


Zone 8: Office (232.842 sq.ft) (Group 0)
Cooling infiltration method: Direct Cooling infiltration value: 0.000
Heating ventilation method: Direct Heating ventilation value: 7.000
Heating infiltration method: Direct Heating infiltration value: 0.000
Winter exhaust air CFM: 0 Summer exhaust air CFM: 0
Minimum supply CFM: 0 Latent Btuh equipment load: 0
Ceil. exposed to plenum (sq.ft): 233 Exposed floor slab perimeter (ft): 61
Both heating and cooling loads are calculated for this zone.

Zone 9: Toilet (112.6188 sq.ft) (Group 0)


Air Handler number: 1 Zone occurrences: 1
Zone length: (feet) 9.81 Zone width (feet): 11.48
Lighting Watts: 96 Equipment Watts: 0
Number of people in zone: 0 People profile number: 1
Lighting profile number: 2 Equipment profile number: 3
Ceiling height (feet): 13.12 Heating safety factor (%): 10
Sensible safety factor (%): 10 Latent safety factor (%): 10
Sensible heat per person (Btuh): 315 Latent heat per person (Btuh): 325
Cooling ventilation method: Direct Cooling ventilation value: 244.000
Cooling infiltration method: Direct Cooling infiltration value: 0.000
Heating ventilation method: Direct Heating ventilation value: 244.000
Heating infiltration method: Direct Heating infiltration value: 0.000
Winter exhaust air CFM: 244 Summer exhaust air CFM: 244
Minimum supply CFM: 244 Latent Btuh equipment load: 0
Ceil. exposed to plenum (sq.ft): 0 Exposed floor slab perimeter (ft): 42
Both heating and cooling loads are calculated for this zone.

Roof Type ASHRAE# U-Factor Dark Length Width Area Susp.Ceil


1 1 12 0.090 No 11.48 9.81 112.6 Yes

Part Type U-Factor Cool TD Heat TD Height Width Area


1 2 0.133 8.000 12.000 13.12 9.81 128.7

Zone 10: Kitchen (32.2752 sq.ft) (Group 0)


Air Handler number: 1 Zone occurrences: 1
Zone length: (feet) 6.56 Zone width (feet): 4.92
Lighting Watts: 86 Equipment Watts: 500
Number of people in zone: 1 People profile number: 1
Lighting profile number: 2 Equipment profile number: 3
Ceiling height (feet): 13.13 Heating safety factor (%): 10
Sensible safety factor (%): 10 Latent safety factor (%): 10
Sensible heat per person (Btuh): 315 Latent heat per person (Btuh): 325
Cooling ventilation method: Direct Cooling ventilation value: 194.000
Cooling infiltration method: Direct Cooling infiltration value: 0.000
Heating ventilation method: Direct Heating ventilation value: 194.000
Heating infiltration method: Direct Heating infiltration value: 0.000
Winter exhaust air CFM: 194 Summer exhaust air CFM: 194
Minimum supply CFM: 71 Latent Btuh equipment load: 0
Ceil. exposed to plenum (sq.ft): 0 Exposed floor slab perimeter (ft): 23
Both heating and cooling loads are calculated for this zone.

Roof Type ASHRAE# U-Factor Dark Length Width Area Susp.Ceil


1 1 12 0.090 No 6.56 4.92 32.3 Yes

Part Type U-Factor Cool TD Heat TD Height Width Area


1 2 0.133 8.000 12.000 13.12 5.08 66.6
16 of 68
C:\disc top 6h 132_33kv Substation_rev_lighting.CHV Wednesday, February 11, 2009, 10:54 PM
Chvac - Full Commerc
age 8

Zone Input (cont'd)


Zone 10: Kitchen (32.2752 sq.ft) (Group 0)

Zone 11: 33kv Swgr Room (1064.54 sq.ft) (Group 0)


Air Handler number: 1 Zone occurrences: 1
Zone length: (feet) 59.01 Zone width (feet): 18.04
Lighting Watts: 1,814 Equipment Watts: 26,400
Number of people in zone: 2 People profile number: 1
Lighting profile number: 2 Equipment profile number: 3
Ceiling height (feet): 17.70 Heating safety factor (%): 10
Sensible safety factor (%): 10 Latent safety factor (%): 10
Sensible heat per person (Btuh): 315 Latent heat per person (Btuh): 325
Cooling ventilation method: Direct Cooling ventilation value: 496.000
Cooling infiltration method: Direct Cooling infiltration value: 0.000
Heating ventilation method: Direct Heating ventilation value: 496.000
Heating infiltration method: Direct Heating infiltration value: 0.000
Winter exhaust air CFM: 0 Summer exhaust air CFM: 0
Minimum supply CFM: 0 Latent Btuh equipment load: 0
Ceil. exposed to plenum (sq.ft): 0 Exposed floor slab perimeter (ft): 0
Both heating and cooling loads are calculated for this zone.

Roof Type ASHRAE# U-Factor Dark Length Width Area Susp.Ceil


1 1 12 0.102 No 59.00 18.00 1,062.0 No

Part Type U-Factor Cool TD Heat TD Height Width Area


4 2 0.133 8.000 12.000 17.70 2.62 46.4

Wall Type ASHRAE# U-Factor Color Height Width Area Direction


1 2 A 0.105 M 17.70 18.04 319.3 NE
2 2 A 0.105 M 17.70 18.04 319.3 SW
3 2 A 0.105 M 17.70 59.01 1,044.5 NW

Zone 12: Basement (1064.54 sq.ft) (Group 0)


Air Handler number: 1 Zone occurrences: 1
Zone length: (feet) 59.01 Zone width (feet): 18.04
Lighting Watts: 1,037 Equipment Watts: 15,000
Number of people in zone: 0 People profile number: 1
Lighting profile number: 2 Equipment profile number: 3
Ceiling height (feet): 9.40 Heating safety factor (%): 10
Sensible safety factor (%): 10 Latent safety factor (%): 10
Sensible heat per person (Btuh): 315 Latent heat per person (Btuh): 325
Cooling ventilation method: Direct Cooling ventilation value: 259.000
Cooling infiltration method: Direct Cooling infiltration value: 0.000
Heating ventilation method: Direct Heating ventilation value: 259.000
Heating infiltration method: Direct Heating infiltration value: 0.000
Winter exhaust air CFM: 0 Summer exhaust air CFM: 0
Minimum supply CFM: 0 Latent Btuh equipment load: 0
Ceil. exposed to plenum (sq.ft): 0 Exposed floor slab perimeter (ft): 154
Both heating and cooling loads are calculated for this zone.

Part Type U-Factor Cool TD Heat TD Height Width Area


1 2 0.133 8.000 12.000 7.30 18.04 131.7
2 2 0.133 8.000 12.000 7.30 18.04 131.7
3 2 0.133 8.000 12.000 7.30 42.38 309.4
4 2 0.133 8.000 12.000 7.30 17.32 126.4

17 of 68
C:\disc top 6 132_33kv Substation_rev_lighting.CHV Wednesday, February 11, 2009, 10:54 PM
H 132/33KV SUBSTATION
Page 9

Building Summary Loads


Building peaks in August at 3pm.
Bldg Load Area Sen %Tot Lat Sen Net %Net
Descriptions Quan Loss Loss Gain Gain Gain Gain
Roof 5,085 18,661 10.85 0 10,616 10,616 2.36
Wall 4,657 19,365 11.26 0 9,846 9,846 2.19
Glass 0 0 0.00 0 0 0 0.00
Floor Slab 863 8,548 4.97 0 0 0 0.00
Skin Loads 46,574 27.08 0 20,462 20,462 4.55
Lighting 15,445 0 0.00 0 58,941 58,941 13.10
Equipment 53,690 0 0.00 0 201,518 201,518 44.78
People 12 0 0.00 0 4,158 4,158 0.92
Partition 1,087 2,135 1.24 0 1,246 1,246 0.28
Cool. Pret. 0 0 0.00 0 0 0 0.00
Heat. Pret. 0 0 0.00 0 0 0 0.00
Cool. Vent. 3,925 0 0.00 0 82,610 82,610 18.36
Heat. Vent. 3,925 116,795 67.91 0 0 0 0.00
Cool. Infil. 0 0 0.00 0 0 0 0.00
Heat. Infil. 0 0 0.00 0 0 0 0.00
Draw-Thru Fan 0 0 0.00 0 41,661 41,661 9.26
Blow-Thru Fan 0 0 0.00 0 0 0 0.00
Reserve Cap. 0 0 0.00 0 18,775 18,775 4.17
Reheat Cap. 0 0 0.00 0 0 0 0.00
Supply Duct 0 6,489 3.77 0 16,512 16,512 3.67
Return Duct 0 0 0.00 0 4,128 4,128 0.92
Misc. Supply 0 0 0.00 0 0 0 0.00
Misc. Return 0 0 0.00 0 0 0 0.00
Building Totals 171,992 100.00 0 450,011 450,011 100.00

Building Sen %Tot Lat Sen Net %Net


Summary Loss Loss Gain Gain Gain Gain
Ventilation 116,795 67.91 0 82,610 82,610 18.36
Infiltration 0 0.00 0 0 0 0.00
Pretreated Air 0 0.00 0 0 0 0.00
Zone Loads 44,116 25.65 0 269,536 269,536 59.90
Plenum Loads 4,592 2.67 0 35,563 35,563 7.90
Fan & Duct Loads 6,489 3.77 0 62,302 62,302 13.84
Building Totals 171,992 100.00 0 450,011 450,011 100.00

Check Figures
Total Building Supply Air (based on a 20° TD): 19,613 CFM
Total Building Vent. Air (20.01% of Supply): 3,925 CFM
Total Conditioned Air Space: 6,109 Sq.ft
Supply Air Per Unit Area: 3.2107 CFM/Sq.ft
Area Per Cooling Capacity: 162.8971 Sq.ft/Ton
Cooling Capacity Per Area: 0.0061 Tons/Sq.ft
Heating Capacity Per Area: 28.15 Btuh/Sq.ft
Total Heating Required With Outside Air: 171,992 Btuh
Total Cooling Required With Outside Air: 37.50 Tons

18 of 68
C:\disc top 6.2_33kv Substation_rev_lighting.CHV Wednesday, February 11, 2009, 10:54 PM
Chvac - Full Commercial HVAC Loads Calculation Program Elite Software Development, Inc.
UTH 132/33KV SUBSTATION
Page 10

Air Handler #1 - PACU-1&2 - Summary Loads


Zn Description Area Htg.Loss Sen.Gain Lat.Gain Htg.O.A. Clg.O.A.
No Peak Time People Htg.CFM Clg.CFM S.Exh Req.CFM Req.CFM
Volume CFM/Sqft CFM/Sqft W.Exh Act.CFM Act.CFM
1 Battery Room 378 4,994 10,378 0 Direct Direct
8pm August 0 444 1,350 1,350 1,350 1,350
6,307 1.18 3.57 1,350 444 270

2 Store Room 378 4,994 7,054 358 Direct Direct


8pm August 1 444 509 0 37 37
6,307 1.18 1.35 0 444 102

3 Fire Fighting 378 2,935 8,145 358 Direct Direct


8pm August 1 261 1,125 1,125 1,125 1,125
6,307 0.69 2.98 1,125 261 225

4 Ac/dc Room 352 3,071 20,230 358 Direct Direct


12am August 1 273 1,458 0 86 86
4,625 0.78 4.14 0 273 292

5 Telecom 402 1,788 5,493 715 Direct Direct


12am August 2 159 396 0 23 23
5,269 0.40 0.99 0 159 79

6 Passage 281 2,136 1,019 0 Direct Direct


12am August 0 190 73 0 11 11
3,683 0.68 0.26 0 190 15

Control And
1,434 7,889 21,904 1,073 Direct Direct
7 Protection Room
3 702 1,579 0 93 93
12am August
18,817 0.49 1.10 0 702 316

8 Office 233 1,181 1,713 358 Direct Direct


12am August 1 105 123 0 7 7
3,055 0.45 0.53 0 105 25

9 Toilet 113 1,046 762 0 Direct Direct


9pm August 0 93 244 244 244 244
1,478 0.83 2.17 244 93 49

10 Kitchen 32 462 2,696 358 Direct Direct


9pm August 1 41 194 194 194 194
424 1.27 6.02 194 41 39

11 33kv Swgr Room 1,065 10,865 113,227 715 Direct Direct


12am August 2 967 8,162 0 496 496
18,842 0.91 7.67 0 967 1,633

12 Basement 1,065 2,755 61,011 0 Direct Direct


12am August 0 245 4,398 0 259 259
10,007 0.23 4.13 0 245 880

1 Plenum 0 4,592 35,563 0 None None


9pm in August 0 0 0 0 0 0
0 0 0 0 0 0
Zone Peak Totals: 6,109 44,116 289,195 4,290
Total Zones: 12 12 3,925 19,613 2,913 3,925 3,925
Unique Zones: 12 85,119 0.64 3.21 2,913 3,925 3,925
19 of 68
C:\disc top 6. 132_33kv Substation_rev_lighting.CHV Wednesday, February 11, 2009, 10:54 PM
Chvac - Full Commercial HVAC Loads Calculation Program Elite Software Development, Inc.
132/33KV SUBSTATION
Page 11

Air Handler #1 - PACU-1&2 - Total Load Summary


Air Handler Description: PACU-1&2 Constant Volume - Sum of Peaks
Supply Air Fan: Draw-Thru with program estimated horsepower of 21.44 HP
Fan Input: 81% motor and fan efficiency with 5.63 in. water across the fan
Sensible Heat Ratio: 0.99 --- This system occurs 1 time(s) in the building. ---
Air System Peak Time: 3pm in August.
Outdoor Conditions: 102° DB, 63° WB, 50.51 grains
Because of the diversity in zone, plenum and ventilation loads, the zone sensible peak time in August at 10pm is different
from the total system peak time, hence the air system CFM was computed using a zone sensible load of 253,296.
Summer: Ventilation controls outside air, ----- Winter: Ventilation controls outside air.
Zone Space sensible loss: 44,116 Btuh
Infiltration sensible loss: 0 Btuh 0 CFM
Outside Air sensible loss: 116,795 Btuh 3,925 CFM
Supply Duct sensible loss: 6,489 Btuh
Return Duct sensible loss: 0 Btuh
Return Plenum sensible loss: 4,592 Btuh
Total System sensible loss: 171,992 Btuh
Heating Supply Air: 50,605 / (.765 X 1.08 X 16) = 3,925 CFM
Winter Vent Outside Air (100.0% of supply) = 3,925 CFM
Zone space sensible gain: 250,762 Btuh
Infiltration sensible gain: 0 Btuh
Draw-thru fan sensible gain: 41,661 Btuh
Supply duct sensible gain: 16,512 Btuh
Reserve sensible gain: 18,775 Btuh
Total sensible gain on supply side of coil: 327,710 Btuh
Cooling Supply Air: 330,244 / (.765 X 1.1 X 20) = 19,613 CFM
Summer Vent Outside Air (20.0% of supply) = 3,925 CFM
Return duct sensible gain: 4,128 Btuh
Return plenum sensible gain: 35,563 Btuh
Outside air sensible gain: 82,610 Btuh 3,925 CFM
Blow-thru fan sensible gain: 0 Btuh
Total sensible gain on return side of coil: 122,301 Btuh
Total sensible gain on air handling system: 450,011 Btuh
Zone space latent gain: 4,290 Btuh
Infiltration latent gain: 0 Btuh
Outside air latent gain: -82,311 Btuh
Total latent gain on air handling system: -78,021 Btuh
Total system sensible and latent gain: 371,990 Btuh

Check Figures
Total Air Handler Supply Air (based on a 20° TD): 19,613 CFM
Total Air Handler Vent. Air (20.01% of Supply): 3,925 CFM
Total Conditioned Air Space: 6,109 Sq.ft
Supply Air Per Unit Area: 3.2107 CFM/Sq.ft
Area Per Cooling Capacity: 162.8971 Sq.ft/Ton
Cooling Capacity Per Area: 0.0061 Tons/Sq.ft
Heating Capacity Per Area: 28.15 Btuh/Sq.ft
Total Heating Required With Outside Air: 171,992 Btuh
Total Cooling Required With Outside Air: 37.50 Tons
Note: Due to the system's negative latent gain, tonnage is based solely on sensible gain.

20 of 68
C:\disc top 132_33kv Substation_rev_lighting.CHV Wednesday, February 11, 2009, 10:54 PM
Chvac - Full Commercial HVAC Loads Calculation Program Elite Software Development, Inc.
AN
Page 12

Zone Detailed Loads (At Zone Peak Times)


Load Unit -SC- CLTD U.Fac Sen. Lat. Htg. Htg.
Description Quan CFAC SHGF -CLF- Gain Gain Mult. Loss
Zone 1-Battery Room peaks (sensible) in August at 8pm, Air Handler 1 (PACU-1&2), Group 0, 19.7 x 19.2,
Construction Type: 22 (Medium)
Roof-1-12-No.Clg-L 378 0.50 27.5 0.102 1,059 3.672 1,387
Wall-1-SW-A-M 329 0.83 21.7 0.105 748 3.780 1,242
Wall-2-SE-A-M 320 0.83 23.3 0.105 786 3.780 1,211
Lights-Prof=2 835 0.010 2,849
Equipment-Prof=3 1,170 1.000 3,992 0
Floor slab 78 9.000 700
Sub-total 9,435 0 4,540
Safety factors: +10% +10% +10%
--------- --------- ---------
Total w/ safety factors: 10,378 0 4,994

Zone 2-Store Room peaks (sensible) in August at 8pm, Air Handler 1 (PACU-1&2), Group 0, 19.7 x 19.2,
Construction Type: 22 (Medium)
Roof-1-12-No.Clg-L 378 0.50 27.5 0.102 1,059 3.672 1,387
Wall-1-NE-A-M 320 0.83 20.6 0.105 695 3.780 1,211
Wall-2-SE-A-M 329 0.83 23.3 0.105 806 3.780 1,242
Lights-Prof=2 1,037 0.010 3,538
People-Prof=1 1.0 1.000 315 325
Floor slab 78 9.000 700
Sub-total 6,413 325 4,540
Safety factors: +10% +10% +10%
--------- --------- ---------
Total w/ safety factors: 7,054 358 4,994

Zone 3-Fire Fighting peaks (sensible) in August at 8pm, Air Handler 1 (PACU-1&2), Group 0, 19.7 x 19.2,
Construction Type: 22 (Medium)
Roof-1-12-No.Clg-L 378 0.50 27.5 0.102 1,059 3.672 1,387
Wall-1-SE-A-M 320 0.83 23.3 0.105 786 3.780 1,211
Lights-Prof=2 1,037 0.010 3,538
Equipment-Prof=3 500 1.000 1,706 0
People-Prof=1 1.0 1.000 315 325
Floor slab 8 9.000 70
Sub-total 7,404 325 2,668
Safety factors: +10% +10% +10%
--------- --------- ---------
Total w/ safety factors: 8,145 358 2,935

Zone 4-Ac/dc Room peaks (sensible) in August at 12am, Air Handler 1 (PACU-1&2), Group 0, 25.6 x 13.8,
Construction Type: 22 (Medium)
Plenum 352 s:3, w:3 0.750 792 2.250 792
Wall-1-SW-A-M 336 0.83 24.2 0.105 852 3.780 1,269
Lights-Prof=2 1,382 0.010 54
Equipment-Prof=3 4,800 1.000 16,378 0
People-Prof=1 1.0 1.000 315 325
Floor slab 81 9.000 731

21 of 68
C:\disc top 6.0 132_33kv Substation_rev_lighting.CHV Wednesday, February 11, 2009, 10:54 PM
Chvac - Full Commercial HVAC Loads Calculation Program Elite Software Development, Inc.
Page 13

Zone Detailed Loads (At Zone Peak Times) (cont'd)


Load Unit -SC- CLTD U.Fac Sen. Lat. Htg. Htg.
Description Quan CFAC SHGF -CLF- Gain Gain Mult. Loss
Sub-total 18,391 325 2,792
Safety factors: +10% +10% +10%
--------- --------- ---------
Total w/ safety factors: 20,230 358 3,071

Zone 5-Telecom peaks (sensible) in August at 12am, Air Handler 1 (PACU-1&2), Group 0, 25.6 x 15.7,
Construction Type: 22 (Medium)
Plenum 402 s:3, w:3 0.750 905 2.250 905
Lights-Prof=2 1,382 0.010 47
Equipment-Prof=3 1,000 1.000 3,412 0
People-Prof=1 2.0 1.000 630 650
Floor slab 80 9.000 721
Sub-total 4,994 650 1,625
Safety factors: +10% +10% +10%
--------- --------- ---------
Total w/ safety factors: 5,493 715 1,788

Zone 6-Passage peaks (sensible) in August at 12am, Air Handler 1 (PACU-1&2), Group 0, 280.7 x 1.0,
Construction Type: 22 (Medium)
Plenum 281 s:3, w:3 0.750 632 2.250 632
Wall-1-SW-A-M 109 0.83 24.2 0.105 276 3.780 412
Lights-Prof=2 518 0.010 18
Floor slab 100 9.000 898
Sub-total 926 0 1,942
Safety factors: +10% +10% +10%
--------- --------- ---------
Total w/ safety factors: 1,019 0 2,136

Zone 7-Control And Protection Room peaks (sensible) in August at 12am, Air Handler 1 (PACU-1&2),
Group 0, 50.8 x 28.2, Construction Type: 22 (Medium)
Plenum 1,434 s:3, w:3 0.750 3,227 2.250 3,227
Wall-1-NE-A-M 667 0.83 21.5 0.105 1,504 3.780 2,521
Lights-Prof=2 5,184 0.010 179
Equipment-Prof=3 4,120 1.000 14,058 0
People-Prof=1 3.0 1.000 945 975
Floor slab 158 9.000 1,424
Sub-total 19,913 975 7,172
Safety factors: +10% +10% +10%
--------- --------- ---------
Total w/ safety factors: 21,904 1,073 7,889

Zone 8-Office peaks (sensible) in August at 12am, Air Handler 1 (PACU-1&2), Group 0, 15.4 x 15.1,
Construction Type: 22 (Medium)
Plenum 233 s:3, w:3 0.750 524 2.250 524
Lights-Prof=2 1,037 0.010 35
Equipment-Prof=3 200 1.000 682 0
People-Prof=1 1.0 1.000 315 325
22 of 68
C:\disc132_33kv Substation_rev_lighting.CHV Wednesday, February 11, 2009, 10:54 PM
Chvac - Full Commercial HVAC Loads Calculation Program Elite Software Development, Inc.
132/33KV SUBSTATION
Page 14

Zone Detailed Loads (At Zone Peak Times) (cont'd)


Load Unit -SC- CLTD U.Fac Sen. Lat. Htg. Htg.
Description Quan CFAC SHGF -CLF- Gain Gain Mult. Loss
Floor slab 61 9.000 550
Sub-total 1,557 325 1,074
Safety factors: +10% +10% +10%
--------- --------- ---------
Total w/ safety factors: 1,713 358 1,181

Zone 9-Toilet peaks (sensible) in August at 9pm, Air Handler 1 (PACU-1&2), Group 0, 9.8 x 11.5,
Construction Type: 22 (Medium)
Roof-1-12-Susp.C-L 113 0.50 22.5 0.090 228 3.240 365
Partition-1-2 128.7072 8/12 0.133 137 1.596 205
Lights-Prof=2 96 0.010 328
Floor slab 42 9.000 381
Sub-total 693 0 951
Safety factors: +10% +10% +10%
--------- --------- ---------
Total w/ safety factors: 762 0 1,046

Zone 10-Kitchen peaks (sensible) in August at 9pm, Air Handler 1 (PACU-1&2), Group 0, 6.6 x 4.9,
Construction Type: 22 (Medium)
Roof-1-12-Susp.C-L 32 0.50 22.5 0.090 65 3.240 105
Partition-1-2 66.6496 8/12 0.133 71 1.596 106
Lights-Prof=2 86 0.010 293
Equipment-Prof=3 500 1.000 1,706 0
People-Prof=1 1.0 1.000 315 325
Floor slab 23 9.000 209
Sub-total 2,451 325 420
Safety factors: +10% +10% +10%
--------- --------- ---------
Total w/ safety factors: 2,696 358 462

Zone 11-33kv Swgr Room peaks (sensible) in August at 12am, Air Handler 1 (PACU-1&2), Group 0, 59.0
x 18.0, Construction Type: 22 (Medium)
Roof-1-12-Susp.C-L 1,062 0.50 21.0 0.090 2,007 3.240 3,441
Wall-1-NE-A-M 319 0.83 21.5 0.105 720 3.780 1,207
Wall-2-SW-A-M 319 0.83 24.2 0.105 811 3.780 1,207
Wall-3-NW-A-M 1,044 0.83 22.3 0.105 2,446 3.780 3,948
Partition-4-2 46.374 8/12 0.133 49 1.596 74
Lights-Prof=2 1,814 0.010 6,190
Equipment-Prof=3 26,400 1.000 90,081 0
People-Prof=1 2.0 1.000 630 650
Sub-total 102,934 650 9,877
Safety factors: +10% +10% +10%
--------- --------- ---------
Total w/ safety factors: 113,227 715 10,865

Zone 12-Basement peaks (sensible) in August at 12am, Air Handler 1 (PACU-1&2), Group 0, 59.0 x 18.0,
Construction Type: 22 (Medium)
23 of 68
C:\disc 32_33kv Substation_rev_lighting.CHV Wednesday, February 11, 2009, 10:54 PM
Chvac - Full Commercial HVAC Loads Calculation Program Elite Software Development, Inc.
132/33KV SUBSTATION
Page 15

Zone Detailed Loads (At Zone Peak Times) (cont'd)


Load Unit -SC- CLTD U.Fac Sen. Lat. Htg. Htg.
Description Quan CFAC SHGF -CLF- Gain Gain Mult. Loss
Partition-1-2 131.692 8/12 0.133 140 1.596 210
Partition-2-2 131.692 8/12 0.133 140 1.596 210
Partition-3-2 309.374 8/12 0.133 329 1.596 494
Partition-4-2 126.436 8/12 0.133 135 1.596 202
Lights-Prof=2 1,037 0.010 3,538
Equipment-Prof=3 15,000 1.000 51,182 0
Floor slab 154 9.000 1,389
Sub-total 55,464 0 2,505
Safety factors: +10% +10% +10%
--------- --------- ---------
Total w/ safety factors: 61,011 0 2,755

Plenum 1- peaks in August at 9pm., Construction Type: 22 (Medium)


Pl.Credit Cool. 2,702 -3 0.750 -6,080
Pl.Credit Heat. 2,702 -3 0.750 -2.250 -6,080
Roof-1-12-Susp.C-L 2,745 0.50 22.5 0.090 5,559 3.240 8,894
Wall-1-NE-A-M 244 0.83 21.5 0.105 550 3.780 922
Partition-2-3 146.28 3/10 0.300 132 3.000 439
Lighting 9,500 32,975
Sub-total 33,135 0 4,175
Safety factors: +10% +10% +10%
--------- --------- ---------
Total w/ safety factors: 36,449 0 4,592

24 of 68
C:\disc top 6h 132_33kv Substation_rev_lighting.CHV Wednesday, February 11, 2009, 10:54 PM
32/33KV SUBSTATION
Page 16

Air System #1 (PACU-1&2) Psychrometric Analysis


System Load Analysis Latent Grains Sensible Temp CFM
Leaving Coil Condition 90.380 57.000
Draw-Thru Fan 41,661 2.523 2,474
Misc Load on Supply Side 0 0.000 0
Supply Air Duct 16,512 1.000 981
Zone Loads 4,290 0.420 253,296 15.340 15,043
Sensible Reserve 18,775 1.137 1,115
Zone Condition 4,290 90.800 330,244 77.000 19,613
Return Air Duct 4,128 0.250
Return Air Plenum 35,563 2.693
Misc Load on Return Side 0 0.000
Vent Air 3,925 CFM -82,311 -8.064 82,610 4.414
Blow-Thru Fan 0 0.000
Entering Coil Condition -78,021 82.737 452,545 84.357 19,613

General Psychrometric Equations Used In Analysis:


PR = (Barometric pressure of site / Standard ASHRAE pressure of 29.921)
TSH = PR x 1.10 x CFM x (DB entering - DB leaving)
TLH = PR x 0.68 x CFM x (Grains entering - Grains leaving)
GTH = PR x 4.50 x CFM x (Enthalpy entering - Enthalpy leaving)

TSH = 0.765 x 1.10 x 19,613 x( 84.357 - 57.000 )= 451,719 Btuh


TLH = 0.765 x 0.68 x 19,613 x( 82.737 - 90.380 )= -78,020 Btuh
----------
SUM = 373,698 Btuh
GTH = 0.765 x 4.50 x 19,613 x( 33.231 - 27.708 )= 373,064 Btuh
Total System Load = 371,990 Btuh

Chilled and Hot Water Flow Rates and Steam Requirement


Cooling GPM = 373,064 / ( 0.00 x 500 ) = 0.0 GPM
Heating GPM = 171,992 / ( 0.00 x 500 ) = 0.0 GPM
Steam Req. = 171,992 / 0 = 0.0 lb./hr

Entering Cooling Coil Conditions Entering Heating Coil Conditions


Dry bulb temperature: 84.36 Dry bulb temperature: 39.00
Wet bulb temperature: 63.72
Relative humidity: 35.91
Enthalpy: 33.23 Btu/lbm

Leaving Cooling Coil Conditions Leaving Heating Coil Conditions


Dry bulb temperature: 57.00 Dry bulb temperature: 90.60
Wet bulb temperature: 56.89
Relative humidity: 99.39
Enthalpy: 27.71 Btu/lbm

25 of 68
C:\disc to132_33kv Substation_rev_lighting.CHV Wednesday, February 11, 2009, 10:54 PM
7 VENTILATION, EXHAUST AND PRESSURIZATION :

7.1 EXHAUST AND VENTILATION CALCULATION:


7.1.1 Ventilation
We shall design the system in such a way that a positive pressurization is achieved. Introduction of
Outdoor air into the system through a fresh air opening / grilles into the machine room shall eventually
produce heat both sensible and latent in nature.

Qs = 1.1 x (To - TR) x CFM ------------------------ (1 )

QL = 4840 x (Wo - Wi ) x CFM ------------------------ (2 )

Where :
Qs = Sensible heat gain, BTU/Hr.
QL = Latent heat gain, BTU/Hr.
o
To = Design outside ambient temperature - 110 F
o
TR = Room design temperature. 77 F
Wo = Outside Air Humidity ratio # W.V / # water
Wi = Room air humidity ratio # W.V / # Water.
CFM = Ventilation rate requirement.

Please refer to the Computer Generated Calculation Sheets enclosed with this document for the details.

7.1.2
7 1 2 Exhaust

a) Battery room

From SES-K-100 clause No. 10.11 the recommended air changes for the Battery room is 12. Hence No. of
air changes considered in the calculation is 12 AC/Hr. The detailed calculation of the Battery room exhaust
system is enclosed.

b) Toilet room

From SES-K-100 clause No. 10.11 the recommended air changes for the Toilet room is 10. Hence No. of
air changes considered in the calculation is 10 AC/Hr. The detailed calculation of the toilet room exhaust
system is enclosed.

26 of 68
7.2 PRESSURIZATION

7.2.1 Site Condition


o o
Outside temperature : 102 F 39 C
o
Prevailing wind direction : 7 NW
Wind speed : 15 mph
Building pressure : 50 Pa

7.2.2 Wind pressure (Ref. ASHRAE Fundamental 1997 Chapter 25)


2
Wind static pressure: Pv = 1/2 (C1*C2*p*V ) - Equation No.6 Chapter 23 of
ASHRAE Fundamental.
Where :
Pv = Surface pressure relative to static pressure in
Undistributed flow : in of water.

C1 = 0.0129 Unit conversion factor


C2 = wind surface pressure co-efficient
= 1 for the undistributed area

3
p = Air density in lb/ft
= 0.0686 at102Deg.F

V = Wind speed in MPH


= 15 MPH (Taken from SES-K-100)
Hence
Pv = 1/2*(0.0129x1x0.0686x15^2)
= 0.0995 inches of W.G.
= 0.0995 inches of W.G.

7.2.3 Ex-filtration shall be calculated as below:


Qp = Qexh+Po/Pi Qexh+Po/PiQx+Qx
Where :
Qexh = Exhaust air in CFM
Qx = Ex-Filtration in CFM

P0=Pv = Outside Static Pressure on building wall


= 0.0995 (Ref. To above calculation)

Pi = Inside Static pressure of the space.


= P0 + 0.2 in W.G
= 0.0995 + 0.2 in W.G
= 0.2995 in W.G

27 of 68
Qexh= Exhaust air in Battery room +Exhaust air Toilet room+Kitchen+fire fighting
= 1350+ 244+ 194+ 1125= 2913 CFM
(Ref. To detailed calculation of Battery room and
toilet room exhaust fan sizing) = 2913 CFM

Make-up air required to pressurize the conditioned space.= Qp ={Qexh + (Po/P1) Qexh + (Po/P1) Qx + Qx}
Where: Qp = Air required to pressurize the space to required
static pressure in CFM
Qexh = Exhaust air by Powered Exhaust fan - in cfm
Qx = Ex-filtration of the air from the space in cfm.
Po = Outside static pressure acting on wall in In. of w.g.
Pi = Inside static pressure of the conditioned space In.w.g.
7.2.4 Assumptions:
In this design, for the purpose of analysis, following assumptions are made:
Design Static pressure inside the conditioned space to be positive relative to atmosphere.
As per SES-K-100 & SES-P-119.43, the required pressure inside the conditioned space
shall be maintained at 0.2 inches of w.g.
Surface pressure relative to the static pressure is equivalent to the static pressure acting
on the building wall. I.e. P0=Pv = 0.0995 in of W.G
Qexh = 2913 cfm (Exhaust in Battery room&Toilet room)
Qx = 31 cfm
Qp =
Qp = {Qexh + (Po/P1) Qexh + (Po/P1) Qx + Qx}
Qp = {2913+(0.0995/0.2995)x2913+{(0.0995/0.2995) x 31+ 31}
Qp = 3910 CFM
Note: As per SES-K-100, Sec.-10, minimum of 10% of supply air required for fresh
air make up. From air balancing table enclosed, required make up is greater
than the Qp indicated above.

Fresh
F h Air
Ai is
i considering
id i as follows
f ll :

1. Fresh Air = 5% of Supply Air + Exhaust air + Exfiltration Air


= 19,613 x 0.05 + 2,913 + 31 = 3925 CFM (Biggest value)

2. Fresh Air = Pressurization Air + Exhaust Air + Exfiltration Air


from article 7.2.4 = 3910 CFM
3. Fresh Air = 10% Supply Air
= 1961 CFM

Summary is as below:
Total Supply Total Outside Exhaust Air %.O.A. % Press.
Area
Air - CFM Air CFM CFM - -
SWGR and Cont. Build. 19,613 3,925 2,913 20.0% 5.9%

Percent of outside air = Outside Air x 100


Supply air

Percent of Press. Air = (Outside Air - Exhaust air ) x 100


Supply air

28 of 68
7.3 AIR BALANCING:

Supply Air Return Air Exhaust Air Press. Air Ex.A


SL# Zone Name
CFM CFM CFM CFM CFM
0 1 BATTARY ROOM 1,350 0 1350 0 0
37 2 STORE ROOM 509 472 0 30 7
0 3 FIRE FIGHTING ROOM 1,125 0 1125 0 0
86 4 AC/DC ROOM 1,458 1,372 0 86 0
23 5 TELECOM 396 373 0 23 0
11 6 PASSAGE 73 62 0 4 7
93 7 CONTROL ROOM 1,579 1,486 0 93 0
7 8 OFFICE 125 118 0 7 0
0 9 TOILET 244 0 244 0 0
10 KITCHEN 194 0 194 0 0
11 33KV SWGR ROOM 8,162 7,666 0 479 17
259 12 BASEMENT 4,398 4,139 0 259 0
TOTAL 19,613 15,688 2,913 981 31

Total Supply air = 19,613 CFM


Return Air = 15,688 CFM
Exhaust air = 2913 CFM
Press. Air = 981 CFM
Exf. Air = 31 CFM
Outside air = Exhaust air + Press. Air + Exfiltration Air
=
= 3,925 CFM
Adopt outside air= 3,925 CFM
Supply air = Return Air + Outside air.
= 15688 + 3925
= 19,613 CFM
Total Tonnage required with outside air = 37.5 Tons.

Total Static Pressure = Internal Static Pressure + External Static Pressure

= 1.89 + 3.5 = 5.39 " w.g.

Say = 1350 Pa

ISP Details: 1 Casing = 0.15 inch of w.g.


2 Cooling Coil = 0.74 inch of w.g.
3 Filters = 1.5 inch of w.g.
4 Mixing Box = 0.13 inch of w.g.

2.52 inch of w.g.

29 of 68
Exfiltration (Qx)

PW = Wind surface pressure relative to static pressure, in undisturbed flow, in, water.
QX = Ex-filtration in CFM
QX/L = Stack co-efficient, (CFM)2 (Sq. in )-2 (F)-1 = (( Ax ΔT) + (BxV2)1/2
0 = Stack co-efficient
= 0.0156 (Ref. ASHRAE fundamentals 1997 chapter 25, Table 6
ΔT = Indoor temp. - Outdoor temp. = 77-109 = -32OF
1 = Wind co-efficient, (CFM)2 (Sq. in)-2 (mph)-2
= 0.0119 (shielding class-1) ASHRAE fundamentals 1977,
= chapter 25 table 7
V = Wind speed = 15 mph
L = Leakage area In2
QX/L = ((0.0156 x -43) + (0.0119 x 152))1/2 CFM/In2
= (2.01)1/2 = 1.42 CFM/In2

Use 0.12 in2/ft2 for (Double door & single door weather stripped Ref. ASHRAE fundamentals.

Room Name Door Designation Door Area M2 [Ft]2 Leakage Area (in)2 Leakage Air
cfm
BATTARY ROOM Ds 2.6 [28] - 0
STORE ROOM Dd 3.7 [39.8] 5.00 7
FIRE F. ROOM Ds 2.6 [28] - 0
AC/DC ROOM Ds 2.6 [28] - 0
TELECOM ROOM Ds 2.6 [28] - 0
PASSAGE Dd 3.7 [39.8] 5.00 7
CONTROL ROOM Dd 3.7 [39.8] - 0
OFFICE 2.6 [28] - 0
TOILET 2.6 [28] - 0
KITCHEN 2.6 [28] - 0
33KV SWGR ROOM Dd+2Ds 8.9 [95.7] 12 17
BASEMENT - 0
Note: Ds - Single Door Total CFM = 31
Dd - Double Door

30 of 68
HVAC SYSTEM SEQUENCE OF OPERATION :

CHANGEOVER SWITCH
PACU-1 will be the duty unit, whereas PACU-2 will be the standby unit. When
PACU-1 fails to operate, PACU-2 will be switched on automatically and vice-versa.
Corresponding motorized volume dampers will open for the unit in operation while
close in the "failed" or standby unit.

7- D S CHANGEOVER
A 7 days timer will alternate the running of duty unit and standby unit every 7 days.
If the running unit fails, the change over switch shall automatically run the standby
unit and vice-versa.

SMOKE DETECTION
Presence of smoke will be detected by duct mounted smoke detector to shutdown
the HVAC system and close the combination of motorized fire and smoke
damper(s) (MF/SD-1 & MF/SD-2). A time delay will be provided so that MF/SD-1 &
MF/SD-2 will be fully opened before the HVAC system is restarted with the unit
selector switch.

COOLING
The main controller will energize the lead compressor (Compr. No. 1) when the
room temperature is above the set point. The second compressor (Compr. No. 2)
will be energized as well when further cooling is required. BOTH Compressors will
run until the set point of the main controller is achieved.

HEATING
When the room temperature is below the set point of the main controller, this
controller will send signal to the 2-stage controller to energize the electric duct
heater in 1 or 2 stages as required until the desired room temperature is achieved.

DEHUMIDIFICATION
Space air humidity conditions are measured by a duct mounted temperature /
humidity detector and the measured humidity values are transmitted to the DDC
(MEC) controller via analog module. The controller compares the actual values with
required humidity values (50%) and if the humidity is higher, the controller overrides
the temperature control process and operates the compressors to de-humidify the
air to maintain the set point (adjustable 0-100%). As selected on the local user
interface on the HVAC control panel. During dehumidifying process the controller
retains the control of the heater to maintain the room dry bulb conditions.

31 of 68
NO AIRFLOW and FAN BELT FAILURE
AFS-1 and AFS-2 shall have two functions, one is to shut-off the corresponding
electric heater in the event of no airflow. The other is to give only an indication light
on the HVAC control panel when there is fan belt failure then automatically the
standby unit shall take over. The indicating light should not lit when one PACU is
shut down for standby.

DIRTY FILTER
Differential pressure switches DPS will measure the pressure drop across the filter
and if the pressure differential setting is reached, a lamp will glow sending signal to
the HVAC control panel to indicate that the filters are dirty and require replacement
/ cleaning.

H-O-A FOR PACU-1 & PACU-2


On automatic position (A), PACU-1 (duty) will run continuously during cooling,
heating and dehumidification requirement. PACU-1 will switchover to PACU-2
(standby) if trouble occurs in the system due to fault or by seven days changeover
scheme. At hand position (H), only the selected PACU will run.

HI/LO PRESSURE
The high discharge and low suction pressure of the compressor will be monitored
through indicating lamps on the HVAC control panel.

A/C POWER INDICATOR


This indicating lamp will monitor the operation of the PACU-1&2 on the HVAC
control panel.

ANTI-RECYCLE PROTECTION
A minimum of 10 minutes time delay shall project the compressor from restarting in
case of power failure. This shall be accomplished in two equal stages. The first one
shall be taken care by a 5-minute time delay relay installed in the HVAC control
panel in the event of power failure. The second one shall be activated by a built-in
5-minute time delay normal condition, the compressor shall always start from a 5-
minute time delay at the beginning of another cooling cycle.

32 of 68
DUCT SIZING
CALCULATION

33 of 68
132/33KV SUBSTATION
HVAC Duct Sizing
for

34 of 68
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 2

General Project Data Input


General Project Information
Project file name: C:\disc top 6.02
Project title:132/33KV SUBSTATION
Designed by:
Project date:
Project comment: JOB ORDER NO. PLANT
NO.
Client name:
Client address:
Company name:
Company representative:

35 of 68
C:\disc top 6.02DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 3

System 1 "PACU 1&2" - Input Data - Supply


Project & Default Data Trunks Runouts
Maximum desired velocity (FPM): 1,650 600
Material Reference: Galv Rect Galv Rect
Height constraint (in): 26 16
Width constraint (in): 64 30
Diameter constraint (in): 48 24
R-Value of insulation (Sq.ft.F/Btuh): 4.00 2.00
Duct shape: Rect. Rect.
Sizing method: EF EF
NC criteria: N/A 40

Duct System Data


Maximum system velocity (FPM): 1,605.0
Minimum system velocity (FPM): 500.0
Minimum trunk diameter (in): 8.0
Orifice opening interval (in): 1.000
Temperature of air leaving coil (°F): 57
Design room temperature (°F): 77
Temperature of duct installation space (°F): 80
Altitude (ft): 8,200
Density (lb/cu.ft): 0.057
Friction loss per 100 ft. (in.wg): 0.100
Est. st. press. loss of central equip. (in.wg): 0.300
Maximum % supply air increase: 0
Allow increasing downstream diameters: No
Show diversified trunk flows: No
Duct diameter interval (in): 0.0
Whole number dimensions: No

Fan Data
Fan description:
Fan static pressure (in.wg): 0.000
Fan CFM: 0
Fan efficiency: 0
Fan RPM: 0
Number of blades: 0
Fan blast width (in): 0
Fan blast height (in): 0
Length to first fitting (ft): 1.0

36 of 68
C:\disc top 6.02DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 4

System 1 "PACU 1&2" - Input Data - Return


Project & Default Data Trunks Runouts
Maximum desired velocity (FPM): 1,650 600
Material Reference: Galv Rect Galv Rect
Height constraint (in): 26 26
Width constraint (in): 64 50
Diameter constraint (in): 48 48
R-Value of insulation (Sq.ft.F/Btuh): 2.00 2.00
Duct shape: Rect. Rect.
Sizing method: EF EF
NC criteria: N/A 40

Duct System Data


Maximum system velocity (FPM): 1,605.0
Minimum system velocity (FPM): 299.0
Minimum trunk diameter (in): 12.0
Orifice opening interval (in): 1.000
Temperature of air leaving coil (°F): 57
Design room temperature (°F): 77
Temperature of duct installation space (°F): 80
Altitude (ft): 50
Density (lb/cu.ft): 0.077
Friction loss per 100 ft. (in.wg): 0.080
Est. st. press. loss of central equip. (in.wg): 0.000
Maximum % supply air increase: 0
Allow increasing downstream diameters: No
Show diversified trunk flows: No
Duct diameter interval (in): 0.0
Whole number dimensions: No

Fan Data
Fan description:
Fan static pressure (in.wg): 0.000
Fan CFM: 0
Fan efficiency: 0
Fan RPM: 0
Number of blades: 0
Fan blast width (in): 0
Fan blast height (in): 0
Length to first fitting (ft): 1.0

37 of 68
C:\disc top 6.0UCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 5

System 1 "PACU 1&2" - Trunk Input Data - Supply


Trunk Dia Length Fit 1 #Fit Shape Active Material Ref.
Ups. Hei Max.Vel Fit 2 #Fit Add.Loss Take Off Roughness
SM Wid Junc fit #Fit R-Value Per.Div
ST-100 48.0 11.00 CR9-3 1 Rect. Yes Galv Rect
FAN 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-120 48.0 14.00 CR9-6 1 Rect. Yes Galv Rect


ST-480 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-130 48.0 11.50 ---- Rect. Yes Galv Rect


ST-120 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-140 48.0 5.50 ---- Rect. Yes Galv Rect


ST-130 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-1 1 4.00 0

ST-170 48.0 7.50 CR9-5 1 Rect. Yes Galv Rect


ST-450 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-180 48.0 14.00 ---- Rect. Yes Galv Rect


ST-170 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-190 48.0 6.00 ---- Rect. Yes Galv Rect


ST-170 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-230 48.0 17.00 CR9-5 1 Rect. Yes Galv Rect


ST-490 26.0 1,650.0 CR3-1 1 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-240 48.0 5.00 ---- Rect. Yes Galv Rect


ST-230 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-250 48.0 9.00 ---- Rect. Yes Galv Rect


ST-240 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-260 48.0 9.50 ---- Rect. Yes Galv Rect


ST-250 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-270 48.0 5.50 ---- Rect. Yes Galv Rect


ST-230 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-280 48.0 8.00 ---- Rect. Yes Galv Rect


ST-270 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-290 48.0 8.50 ---- Rect. Yes Galv Rect


ST-280 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-300 48.0 7.00 ---- Rect. Yes Galv Rect


38 of 68
C:\disc top 6.02\DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 6

System 1 "PACU 1&2" - Trunk Input Data - Supply (cont'd)


Trunk Dia Length Fit 1 #Fit Shape Active Material Ref.
Ups. Hei Max.Vel Fit 2 #Fit Add.Loss Take Off Roughness
SM Wid Junc fit #Fit R-Value Per.Div
ST-480 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-310 48.0 9.50 ---- Rect. Yes Galv Rect


ST-300 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-320 48.0 3.50 ---- Rect. Yes Galv Rect


ST-310 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-330 48.0 5.50 CR9-5 1 Rect. Yes Galv Rect


ST-300 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-340 48.0 8.00 CR9-5 1 Rect. Yes Galv Rect


ST-310 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-350 48.0 4.61 CR9-5 1 Rect. Yes Galv Rect


ST-320 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-370 48.0 6.00 ---- Rect. Yes Galv Rect


ST-390 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-380 48.0 7.50 ---- Rect. Yes Galv Rect


ST-370 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-390 48.0 8.00 ---- Rect. Yes Galv Rect


ST-460 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-400 48.0 10.50 ---- Rect. Yes Galv Rect


ST-460 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-410 48.0 2.50 ---- Rect. Yes Galv Rect


ST-400 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-420 48.0 4.00 ---- Rect. Yes Galv Rect


ST-400 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-430 48.0 3.50 ---- Rect. Yes Galv Rect


ST-140 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-440 48.0 14.00 CR9-5 1 Rect. Yes Galv Rect


ST-290 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-450 48.0 4.50 ---- Rect. Yes Galv Rect


ST-430 26.0 1,650.0 ---- 0.00 0 0.00050
39 of 68
C:\disc top 6.02\ DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 7

System 1 "PACU 1&2" - Trunk Input Data - Supply (cont'd)


Trunk Dia Length Fit 1 #Fit Shape Active Material Ref.
Ups. Hei Max.Vel Fit 2 #Fit Add.Loss Take Off Roughness
SM Wid Junc fit #Fit R-Value Per.Div
EF 64.0 SR5-5 1 4.00 0

ST-460 48.0 16.00 ---- Rect. Yes Galv Rect


ST-120 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-470 48.0 5.00 ---- Rect. Yes Galv Rect


ST-370 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-480 48.0 19.00 ---- Rect. Yes Galv Rect


ST-230 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

ST-490 48.0 4.50 ---- Rect. Yes Galv Rect


ST-100 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 4.00 0

40 of 68
C:\disc top 6.02\DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 8

System 1 "PACU 1&2" - Trunk Input Data - Return


Trunk Dia Length Fit 1 #Fit Shape Active Material Ref.
Ups. Hei Max.Vel Fit 2 #Fit Add.Loss Take Off Roughness
SM Wid Junc fit #Fit R-Value Per.Div
RT-100 48.0 14.50 CR3-1 1 Rect. Yes Galv Rect
FAN 26.0 1,650.0 CR9-5 1 0.00 0 0.00050
EF 64.0 SR5-5 1 2.00 0
Fit 3 CR9-3 1
Fit 4 CR9-4 1

RT-110 48.0 18.00 CR9-5 2 Rect. Yes Galv Rect


RT-100 26.0 1,650.0 ---- 0.00 0 0.00050
EF 64.0 SR5-5 1 2.00 0

41 of 68
C:\disc top 6.02\ DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 9

System 1 "PACU 1&2" - Runout Input Data - Supply


Runout Dia Length Fit 1 #Fit Shape Active Material Ref.
Ups. Hei Max.Vel Fit 2 #Fit Add.Loss Take Off Roughness
SM Wid Fit 3 #Fit R-Value NC Level Dif.Loss
SR-100 24.0 3.04 ---- Rect. Yes Galv Rect
ST-120 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-110 24.0 6.50 ---- Rect. Yes Galv Rect


ST-450 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-120 24.0 3.04 ---- Rect. Yes Galv Rect


ST-300 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-130 24.0 4.50 CR9-5 1 Rect. Yes Galv Rect


ST-430 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-140 24.0 4.00 ---- Rect. Yes Galv Rect


ST-170 12.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-150 24.0 3.91 ---- Rect. Yes Galv Rect


ST-190 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-160 24.0 6.02 ---- Rect. Yes Galv Rect


ST-180 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-170 24.0 5.59 ---- Rect. Yes Galv Rect


ST-420 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-180 24.0 4.03 ---- Rect. Yes Galv Rect


ST-390 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-190 24.0 7.00 ---- Rect. Yes Galv Rect


ST-380 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-200 24.0 5.10 ---- Rect. Yes Galv Rect


ST-410 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-210 24.0 7.00 ---- Rect. Yes Galv Rect


ST-470 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-230 24.0 3.54 ---- Rect. Yes Galv Rect


ST-260 12.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-240 24.0 3.16 ---- Rect. Yes Galv Rect


ST-250 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-250 24.0 4.50 ---- Rect. Yes Galv Rect


42 of 68
C:\disc top 6.02\DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
32/33KV SUBSTATION
Page 10

System 1 "PACU 1&2" - Runout Input Data - Supply (cont'd)


Runout Dia Length Fit 1 #Fit Shape Active Material Ref.
Ups. Hei Max.Vel Fit 2 #Fit Add.Loss Take Off Roughness
SM Wid Fit 3 #Fit R-Value NC Level Dif.Loss
ST-240 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-260 24.0 2.50 ---- Rect. Yes Galv Rect


ST-270 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-270 24.0 2.55 ---- Rect. Yes Galv Rect


ST-280 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-280 24.0 1.50 ---- Rect. Yes Galv Rect


ST-290 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-290 24.0 1.58 ---- Rect. Yes Galv Rect


ST-350 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-300 24.0 4.00 ---- Rect. Yes Galv Rect


ST-340 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-310 24.0 1.50 ---- Rect. Yes Galv Rect


ST-330 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

SR-320 24.0 2.50 ---- Rect. Yes Galv Rect


ST-440 16.0 600.0 ---- 0.00 0 0.00050
EF 30.0 ---- 2.00 40 0.200

43 of 68
C:\disc top 6.02\ALDUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 11

System 1 "PACU 1&2" - Runout Input Data - Return


Runout Dia Length Fit 1 #Fit Shape Active Material Ref.
Ups. Hei Max.Vel Fit 2 #Fit Add.Loss Take Off Roughness
SM Wid Fit 3 #Fit R-Value NC Level Grille.Loss
RR-100 48.0 2.00 ---- Rect. Yes Galv Rect
RT-110 26.0 600.0 ---- 0.00 0 0.00050
EF 50.0 ---- 2.00 40 0.000

RR-110 48.0 7.00 ---- Rect. Yes Galv Rect


RT-100 26.0 600.0 ---- 0.00 0 0.00050
EF 50.0 ---- 2.00 40 0.000

44 of 68
C:\disc top 6.02\ DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 12

System 1 "PACU 1&2" - Trunk Output Data - Supply


Duct Sect Sect Cumul Press
------ ------ ------ ------ ------
Trunk Dia SM L/100 Shape Ups.Sh Fit Equip Dynam Vel.P Veloc
Upstr Hei TOA Reg Fit.1 Qty Coef Loss Add.L Fric Stat Stat
Vel Wid Gau Fit.2 Qty Coef Loss F.Tot Total Total Total
CFM Len Ref Mat Ups.Junc Coef Loss Dynam
ST-100 41.5 EF 0.090 Rect N/A ---- 0.300 0.958 0.000 0.207
FAN 26.0 0 0.000 CR9-3 1 0.520 0.094 0.000 0.010 0.967 1.005
2,088 57.6 20 ---- 0.958 0.967 0.967 1.212
19,612 11.0 Galv Rect 0.958

ST-120 27.3 EF 0.085 Rect Rect ---- 0.000 0.021 0.088 0.118
ST-480 24.0 0 -0.017 CR9-6 1 0.190 0.020 0.000 0.012 1.351 0.621
1,579 26.0 22 ---- 0.021 0.033 1.440 0.739
6,418 14.0 Galv Rect SR5-5-MN 0.014 0.001 0.021

ST-130 21.9 EF 0.110 Rect Rect ---- 0.000 0.015 0.088 0.118
ST-120 20.0 0 -0.015 ---- 0.000 0.013 1.379 0.593
1,579 20.0 22 ---- 0.015 0.027 1.467 0.712
4,131 11.5 Galv Rect SR5-5-MN 0.139 0.015 0.015

ST-140 21.9 EF 0.110 Rect Rect ---- 0.000 0.000 0.088 0.118
ST-130 20.0 0 0.000 ---- 0.000 0.006 1.385 0.587
1,579 20.0 22 ---- 0.000 0.006 1.474 0.706
4,131 5.5 Galv Rect *SR5-5-MN 0.000

ST-170 19.7 EF 0.090 Rect Rect ---- 0.000 0.035 0.123 0.083
ST-450 18.0 0 -0.023 CR9-5 1 0.460 0.034 0.000 0.007 1.411 0.562
1,327 18.0 24 ---- 0.035 0.042 1.534 0.645
2,808 7.5 Galv Rect SR5-5-MN 0.010 0.001 0.035

ST-180 12.0 EF 0.085 Rect Rect ---- 0.000 0.143 0.166 0.041
ST-170 10.0 0 -0.101 ---- 0.000 0.012 1.523 0.449
928 12.0 24 ---- 0.143 0.155 1.689 0.490
729 14.0 Galv Rect SR5-5-MN 3.948 0.143 0.143

ST-190 12.0 EF 0.085 Rect Rect ---- 0.000 0.143 0.166 0.041
ST-170 10.0 0 -0.101 ---- 0.000 0.005 1.516 0.456
928 12.0 24 ---- 0.143 0.148 1.682 0.497
729 6.0 Galv Rect SR5-5-MN 3.948 0.143 0.143

ST-230 41.5 EF 0.090 Rect Rect ---- 0.000 0.253 0.000 0.207
ST-490 26.0 0 -0.253 CR9-5 1 0.460 0.083 0.000 0.015 1.239 0.733
2,088 57.6 20 *CR3-1 1 0.936 0.170 0.253 0.268 1.239 0.940
19,612 17.0 Galv Rect *SR5-5-MN 0.253

ST-240 21.9 EF 0.110 Rect Rect ---- 0.000 0.630 0.091 0.115
ST-230 20.0 0 -0.538 ---- 0.000 0.005 1.783 0.189
1,560 20.0 22 ---- 0.630 0.635 1.875 0.305
4,080 5.0 Galv Rect SR5-5-MN 6.156 0.630 0.630

ST-250 19.7 EF 0.085 Rect Rect ---- 0.000 0.009 0.128 0.078
ST-240 18.0 0 0.029 ---- 0.000 0.008 1.762 0.210
1,285 18.0 24 ---- 0.009 0.016 1.891 0.288
2,720 9.0 Galv Rect SR5-5-MN 0.123 0.009 0.009

ST-260 15.3 EF 0.085 Rect Rect ---- 0.000 0.019 0.153 0.054
ST-250 14.0 0 0.006 ---- 0.000 0.008 1.765 0.208
1,065 14.0 24 ---- 0.019 0.027 1.918 0.261
45 of 68
C:\disc top 6.02DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 13

System 1 "PACU 1&2" - Trunk Output Data - Supply (cont'd)


Duct Sect Sect Cumul Press
------ ------ ------ ------ ------
Trunk Dia SM L/100 Shape Ups.Sh Fit Equip Dynam Vel.P Veloc
Upstr Hei TOA Reg Fit.1 Qty Coef Loss Add.L Fric Stat Stat
Vel Wid Gau Fit.2 Qty Coef Loss F.Tot Total Total Total
CFM Len Ref Mat Ups.Junc Coef Loss Dynam
1,360 9.5 Galv Rect SR5-5-MN 0.400 0.019 0.019

ST-270 31.7 EF 0.070 Rect Rect ---- 0.000 0.072 0.093 0.113
ST-230 26.0 0 0.021 ---- 0.000 0.004 1.222 0.751
1,547 32.4 20 ---- 0.072 0.076 1.315 0.864
8,478 5.5 Galv Rect SR5-5-MN 0.718 0.072 0.072

ST-280 29.4 EF 0.070 Rect Rect ---- 0.000 0.002 0.099 0.108
ST-270 26.0 0 0.003 ---- 0.000 0.006 1.225 0.748
1,510 28.0 22 ---- 0.002 0.008 1.323 0.856
7,118 8.0 Galv Rect SR5-5-MN 0.024 0.002 0.002

ST-290 26.2 EF 0.085 Rect Rect ---- 0.000 0.003 0.095 0.112
ST-280 24.0 0 -0.007 ---- 0.000 0.007 1.239 0.734
1,538 24.0 22 ---- 0.003 0.010 1.333 0.846
5,758 8.5 Galv Rect SR5-5-MN 0.029 0.003 0.003

ST-300 10.9 EF 0.110 Rect Rect ---- 0.000 0.445 0.161 0.046
ST-480 10.0 0 -0.369 ---- 0.000 0.008 1.699 0.274
981 10.0 26 ---- 0.445 0.453 1.860 0.319
636 7.0 Galv Rect *SR5-5-MN 11.201 0.445 0.445

ST-310 9.7 EF 0.095 Rect Rect ---- 0.000 0.005 0.172 0.035
ST-300 8.0 0 0.006 ---- 0.000 0.009 1.702 0.271
854 8.0 26 ---- 0.005 0.014 1.874 0.305
438 9.5 Galv Rect SR5-5-MN 0.108 0.005 0.005

ST-320 9.7 EF 0.020 Rect Rect ---- 0.000 0.006 0.200 0.007
ST-310 8.0 0 0.022 ---- 0.000 0.001 1.681 0.292
378 8.0 26 ---- 0.006 0.007 1.881 0.298
194 3.5 Galv Rect SR5-5-MN 0.668 0.006 0.006

ST-330 9.7 EF 0.010 Rect Rect ---- 0.000 0.029 0.204 0.003
ST-300 8.0 0 0.013 CR9-5 1 0.460 0.002 0.000 0.001 1.686 0.287
244 8.0 26 ---- 0.029 0.030 1.890 0.289
125 5.5 Galv Rect SR5-5-MN 7.382 0.028 0.029

ST-340 9.7 EF 0.035 Rect Rect ---- 0.000 0.010 0.196 0.011
ST-310 8.0 0 0.013 CR9-5 1 0.460 0.007 0.000 0.003 1.691 0.281
475 8.0 26 ---- 0.010 0.013 1.887 0.292
244 8.0 Galv Rect SR5-5-MN 0.269 0.004 0.010

ST-350 9.7 EF 0.020 Rect Rect ---- 0.000 0.004 0.200 0.007
ST-320 8.0 0 -0.004 CR9-5 1 0.460 0.004 0.000 0.001 1.686 0.286
378 8.0 26 ---- 0.004 0.005 1.886 0.293
194 4.6 Galv Rect *SR5-5-MN 0.004

ST-370 10.9 EF 0.110 Rect Rect ---- 0.000 0.005 0.162 0.045
ST-390 10.0 0 -0.001 ---- 0.000 0.006 1.461 0.511
975 10.0 26 ---- 0.005 0.011 1.623 0.556
632 6.0 Galv Rect SR5-5-MN 0.123 0.005 0.005

ST-380 9.7 EF 0.055 Rect Rect ---- 0.000 0.010 0.189 0.018
ST-370 8.0 0 0.018 ---- 0.000 0.004 1.448 0.525
46 of 68
C:\disc top 6.02\ DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 14

System 1 "PACU 1&2" - Trunk Output Data - Supply (cont'd)


Duct Sect Sect Cumul Press
------ ------ ------ ------ ------
Trunk Dia SM L/100 Shape Ups.Sh Fit Equip Dynam Vel.P Veloc
Upstr Hei TOA Reg Fit.1 Qty Coef Loss Add.L Fric Stat Stat
Vel Wid Gau Fit.2 Qty Coef Loss F.Tot Total Total Total
CFM Len Ref Mat Ups.Junc Coef Loss Dynam
616 8.0 26 ---- 0.010 0.014 1.636 0.543
316 7.5 Galv Rect SR5-5-MN 0.400 0.010 0.010

ST-390 13.1 EF 0.090 Rect Rect ---- 0.000 0.026 0.158 0.049
ST-460 12.0 0 -0.001 ---- 0.000 0.007 1.454 0.519
1,013 12.0 24 ---- 0.026 0.034 1.612 0.568
948 8.0 Galv Rect SR5-5-MN 0.617 0.026 0.026

ST-400 14.2 EF 0.085 Rect Rect ---- 0.000 0.013 0.156 0.051
ST-460 12.0 0 0.010 ---- 0.000 0.009 1.445 0.528
1,038 14.0 24 ---- 0.013 0.022 1.600 0.579
1,141 10.5 Galv Rect SR5-5-MN 0.294 0.013 0.013

ST-410 9.7 EF 0.055 Rect Rect ---- 0.000 0.077 0.189 0.018
ST-400 8.0 0 -0.044 ---- 0.000 0.001 1.490 0.483
616 8.0 26 ---- 0.077 0.078 1.679 0.501
316 2.5 Galv Rect SR5-5-MN 3.207 0.077 0.077

ST-420 9.7 EF 0.055 Rect Rect ---- 0.000 0.077 0.189 0.018
ST-400 8.0 0 -0.044 ---- 0.000 0.002 1.491 0.482
616 8.0 26 ---- 0.077 0.079 1.679 0.500
316 4.0 Galv Rect SR5-5-MN 3.207 0.077 0.077

ST-430 21.9 EF 0.110 Rect Rect ---- 0.000 0.003 0.088 0.118
ST-140 20.0 0 -0.003 ---- 0.000 0.004 1.392 0.580
1,579 20.0 22 ---- 0.003 0.007 1.481 0.698
4,131 3.5 Galv Rect *SR5-1-MN 0.030 0.003 0.003

ST-440 22.9 EF 0.100 Rect Rect ---- 0.000 0.051 0.095 0.112
ST-290 20.0 0 -0.051 CR9-5 1 0.460 0.045 0.000 0.014 1.303 0.669
1,538 22.0 22 ---- 0.051 0.065 1.398 0.781
4,398 14.0 Galv Rect SR5-5-MN 0.055 0.005 0.051

ST-450 19.7 EF 0.105 Rect Rect ---- 0.000 0.007 0.111 0.096
ST-430 18.0 0 0.016 ---- 0.000 0.005 1.381 0.591
1,420 18.0 24 ---- 0.007 0.012 1.492 0.687
3,006 4.5 Galv Rect SR5-5-MN 0.081 0.007 0.007

ST-460 17.5 EF 0.095 Rect Rect ---- 0.000 0.123 0.133 0.074
ST-120 16.0 0 -0.079 ---- 0.000 0.015 1.445 0.527
1,251 16.0 24 ---- 0.123 0.138 1.578 0.601
2,089 16.0 Galv Rect SR5-5-MN 1.876 0.123 0.123

ST-470 9.7 EF 0.055 Rect Rect ---- 0.000 0.010 0.189 0.018
ST-370 8.0 0 0.018 ---- 0.000 0.003 1.446 0.526
616 8.0 26 ---- 0.010 0.012 1.635 0.544
316 5.0 Galv Rect SR5-5-MN 0.400 0.010 0.010

ST-480 28.4 EF 0.085 Rect Rect ---- 0.000 0.151 0.085 0.122
ST-230 26.0 0 -0.067 ---- 0.000 0.016 1.322 0.650
1,604 26.0 22 ---- 0.151 0.167 1.407 0.772
7,054 19.0 Galv Rect SR5-5-MN 1.414 0.151 0.151

ST-490 41.5 EF 0.090 Rect Rect ---- 0.000 0.000 0.000 0.207
47 of 68
C:\disc top 6.02\ DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 15

System 1 "PACU 1&2" - Trunk Output Data - Supply (cont'd)


Duct Sect Sect Cumul Press
------ ------ ------ ------ ------
Trunk Dia SM L/100 Shape Ups.Sh Fit Equip Dynam Vel.P Veloc
Upstr Hei TOA Reg Fit.1 Qty Coef Loss Add.L Fric Stat Stat
Vel Wid Gau Fit.2 Qty Coef Loss F.Tot Total Total Total
CFM Len Ref Mat Ups.Junc Coef Loss Dynam
ST-100 26.0 0 0.000 ---- 0.000 0.004 0.971 1.001
2,088 57.6 20 ---- 0.000 0.004 0.971 1.208
19,612 4.5 Galv Rect *SR5-5-MN 0.000

* Loss coefficient for indicated fitting was extrapolated due to table extents being exceeded.

48 of 68
C:\disc top 6.02 DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 16

System 1 "PACU 1&2" - Trunk Output Data - Return


Duct Sect Sect Cumul Press
------ ------ ------ ------ ------
Trunk Dia SM L/100 Shape Ups.Sh Fit Equip Dynam Vel.P Veloc
Upstr Hei TOA Reg Fit.1 Qty Coef Loss Add.L Fric Stat Stat
Vel Wid Gau Fit.2 Qty Coef Loss F.Tot Total Total Total
CFM Len Ref Mat Ups.Junc Coef Loss Dynam
RT-100 41.5 EF 0.085 Rect N/A ---- 0.000 0.440 0.000 0.206
FAN 26.0 0 0.000 *CR3-1 1 0.936 0.169 0.000 0.013 0.452 0.111
1,792 57.6 20 CR9-5 1 0.460 0.083 0.440 0.452 0.452 0.317
16,831 14.5 Galv Rect 0.440
Fit.3: CR9-3 1 0.520 0.094
Fit.4: CR9-4 1 0.520 0.094

RT-110 39.4 EF 0.070 Rect Rect ---- 0.000 0.130 0.053 0.152
RT-100 26.0 0 -0.077 CR9-5 2 0.460 0.062 0.000 0.012 0.542 0.022
1,543 51.4 20 ---- 0.130 0.143 0.595 0.174
13,061 18.0 Galv Rect SR5-5-MN 0.047 0.006 0.130

* Loss coefficient for indicated fitting was extrapolated due to table extents being exceeded.

49 of 68
C:\disc top 6.02\ DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 17

System 1 "PACU 1&2" - Runout Output Data - Supply


Fit Sect Sect Cumul Press
Runout Dia SM L/100 Shape Ups.Sh ------ ------ ------ ------ ------
Conn Hei TOA Reg Fit1 Qty Coef Loss Diff. Dynam Vel.P Veloc
Vel Wid Gau Fit2 Qty Coef Loss Add.L Fric Stat Stat
CFM Len Ref Mat Fit3 Qty Coef Loss F.Tot Total Total Total
Orif R.NC Act.NC Ups.Junc Qty Coef Loss Dynam
SR-100 9.7 EF 0.025 Rect Rect ---- 0.200 0.329 0.200 0.007
ST-120 8.0 0 -0.218 ---- 0.000 0.001 1.570 0.402
386 8.0 26 ---- 0.129 0.330 1.770 0.409
198 3.0 Galv Rect ---- 0.329
4.70 40 30 *SR5-5-MN 1 13.740 0.129

SR-110 9.7 EF 0.025 Rect Rect ---- 0.200 0.315 0.200 0.007
ST-450 8.0 0 -0.227 ---- 0.000 0.001 1.609 0.363
386 8.0 26 ---- 0.115 0.317 1.809 0.370
198 6.5 Galv Rect ---- 0.315
4.70 40 30 *SR5-5-MN 1 12.241 0.115

SR-120 6.6 EF 0.025 Rect Rect ---- 0.200 0.314 0.202 0.004
ST-300 6.0 0 -0.273 ---- 0.000 0.001 1.972 0.000
307 6.0 28 ---- 0.114 0.315 2.175 0.004
73 3.0 Galv Rect ---- 0.314
6.60 40 30 SR5-5-MN 1 28.231 0.114

SR-130 19.7 EF 0.015 Rect Rect ---- 0.200 0.246 0.193 0.013
ST-430 16.0 0 -0.141 CR9-5 1 0.460 0.005 0.000 0.001 1.534 0.439
531 20.4 24 ---- 0.046 0.247 1.727 0.452
1,125 4.5 Galv Rect ---- 0.246
10.70 40 30 SR5-5-MN 1 3.404 0.040

SR-140 19.7 EF 0.025 Rect Rect ---- 0.200 0.208 0.187 0.019
ST-170 12.0 0 -0.144 ---- 0.000 0.001 1.556 0.417
638 28.4 24 ---- 0.008 0.209 1.743 0.436
1,350 4.0 Galv Rect ---- 0.208
11.70 40 30 SR5-5-MN 1 0.490 0.008

SR-150 12.0 EF 0.085 Rect Rect ---- 0.200 0.200 0.166 0.041
ST-190 10.0 0 -0.200 ---- 0.000 0.003 1.720 0.253
928 12.0 24 ---- 0.000 0.203 1.886 0.294
729 3.9 Galv Rect ---- 0.200
9.00 40 30 *SR5-5-MN 1

SR-160 12.0 EF 0.085 Rect Rect ---- 0.200 0.200 0.166 0.041
ST-180 10.0 0 -0.200 ---- 0.000 0.005 1.729 0.244
928 12.0 24 ---- 0.000 0.205 1.894 0.285
729 6.0 Galv Rect ---- 0.200
9.00 40 30 *SR5-5-MN 1

SR-170 9.7 EF 0.055 Rect Rect ---- 0.200 0.200 0.189 0.018
ST-420 8.0 0 -0.200 ---- 0.000 0.003 1.694 0.279
616 8.0 26 ---- 0.000 0.203 1.882 0.297
316 5.6 Galv Rect ---- 0.200
6.70 40 30 *SR5-5-MN 1

SR-180 10.9 EF 0.030 Rect Rect ---- 0.200 0.217 0.195 0.011
ST-390 10.0 0 -0.180 ---- 0.000 0.001 1.635 0.338
488 10.0 26 ---- 0.017 0.219 1.830 0.349
316 4.0 Galv Rect ---- 0.217
5.90 40 30 SR5-5-MN 1 1.770 0.017
50 of 68
C:\disc top 6.02 DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 18

System 1 "PACU 1&2" - Runout Output Data - Supply (cont'd)


Fit Sect Sect Cumul Press
Runout Dia SM L/100 Shape Ups.Sh ------ ------ ------ ------ ------
Conn Hei TOA Reg Fit1 Qty Coef Loss Diff. Dynam Vel.P Veloc
Vel Wid Gau Fit2 Qty Coef Loss Add.L Fric Stat Stat
CFM Len Ref Mat Fit3 Qty Coef Loss F.Tot Total Total Total
Orif R.NC Act.NC Ups.Junc Qty Coef Loss Dynam
SR-190 9.7 EF 0.055 Rect Rect ---- 0.200 0.200 0.189 0.018
ST-380 8.0 0 -0.200 ---- 0.000 0.004 1.651 0.321
616 8.0 26 ---- 0.000 0.204 1.840 0.339
316 7.0 Galv Rect ---- 0.200
6.70 40 30 *SR5-5-MN 1

SR-200 9.7 EF 0.055 Rect Rect ---- 0.200 0.200 0.189 0.018
ST-410 8.0 0 -0.200 ---- 0.000 0.003 1.693 0.280
616 8.0 26 ---- 0.000 0.203 1.881 0.298
316 5.1 Galv Rect ---- 0.200
6.70 40 30 *SR5-5-MN 1

SR-210 9.7 EF 0.055 Rect Rect ---- 0.200 0.200 0.189 0.018
ST-470 8.0 0 -0.200 ---- 0.000 0.004 1.650 0.322
616 8.0 26 ---- 0.000 0.204 1.839 0.340
316 7.0 Galv Rect ---- 0.200
6.70 40 30 *SR5-5-MN 1

13.1 EF 0.030 Rect Rect ---- 0.200 0.208 0.193 0.014


ST-400 12.0 0 -0.171 ---- 0.000 0.003 1.619 0.354
544 12.0 24 ---- 0.008 0.211 1.811 0.368
509 9.5 Galv Rect ---- 0.208
8.10 40 30 SR5-5-MN 1 0.653 0.008

SR-230 15.3 EF 0.085 Rect Rect ---- 0.200 0.200 0.153 0.054
ST-260 12.0 0 -0.200 ---- 0.000 0.003 1.968 0.005
1,065 16.4 24 ---- 0.000 0.203 2.121 0.059
1,360 3.5 Galv Rect ---- 0.200
15.30 40 30 *SR5-5-MN 1

SR-240 19.7 EF 0.025 Rect Rect ---- 0.200 0.207 0.187 0.020
ST-250 16.0 0 -0.148 ---- 0.000 0.001 1.911 0.061
643 20.4 24 ---- 0.007 0.208 2.099 0.081
1,360 3.2 Galv Rect ---- 0.207
16.70 40 30 SR5-5-MN 1 0.400 0.007

SR-250 20.7 EF 0.020 Rect Rect ---- 0.200 0.225 0.191 0.016
ST-240 16.0 0 -0.126 ---- 0.000 0.001 1.910 0.063
582 22.6 24 ---- 0.025 0.226 2.100 0.079
1,360 4.5 Galv Rect ---- 0.225
16.70 40 30 SR5-5-MN 1 1.770 0.025

SR-260 20.7 EF 0.020 Rect Rect ---- 0.200 0.433 0.191 0.016
ST-270 16.0 0 -0.335 ---- 0.000 0.000 1.558 0.415
582 22.6 24 ---- 0.233 0.433 1.748 0.431
1,360 2.5 Galv Rect ---- 0.433
11.70 40 30 SR5-5-MN 1 16.594 0.233

SR-270 20.7 EF 0.020 Rect Rect ---- 0.200 0.323 0.191 0.016
ST-280 16.0 0 -0.231 ---- 0.000 0.000 1.456 0.516
582 22.6 24 ---- 0.123 0.324 1.647 0.532
1,360 2.5 Galv Rect ---- 0.323
11.70 40 30 SR5-5-MN 1 8.778 0.123
51 of 68
C:\disc top 6.02\ DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
H 132/33KV SUBSTATION
Page 19

System 1 "PACU 1&2" - Runout Output Data - Supply (cont'd)


Fit Sect Sect Cumul Press
Runout Dia SM L/100 Shape Ups.Sh ------ ------ ------ ------ ------
Conn Hei TOA Reg Fit1 Qty Coef Loss Diff. Dynam Vel.P Veloc
Vel Wid Gau Fit2 Qty Coef Loss Add.L Fric Stat Stat
CFM Len Ref Mat Fit3 Qty Coef Loss F.Tot Total Total Total
Orif R.NC Act.NC Ups.Junc Qty Coef Loss Dynam
SR-280 20.7 EF 0.020 Rect Rect ---- 0.200 0.269 0.191 0.016
ST-290 16.0 0 -0.173 ---- 0.000 0.000 1.412 0.560
582 22.6 24 ---- 0.069 0.270 1.603 0.576
1,360 1.5 Galv Rect ---- 0.269
11.70 40 30 SR5-5-MN 1 4.951 0.069

SR-290 9.7 EF 0.020 Rect Rect ---- 0.200 0.200 0.200 0.007
ST-350 8.0 0 -0.200 ---- 0.000 0.000 1.886 0.086
378 8.0 26 ---- 0.000 0.200 2.086 0.093
194 1.6 Galv Rect ---- 0.200
6.70 40 30 *SR5-5-MN 1

SR-300 9.7 EF 0.035 Rect Rect ---- 0.200 0.200 0.196 0.011
ST-340 8.0 0 -0.200 ---- 0.000 0.001 1.892 0.080
475 8.0 26 ---- 0.000 0.201 2.088 0.091
244 4.0 Galv Rect ---- 0.200
7.70 40 30 *SR5-5-MN 1

SR-310 6.6 EF 0.065 Rect Rect ---- 0.200 0.200 0.194 0.013
ST-330 6.0 0 -0.210 ---- 0.000 0.001 1.897 0.075
526 6.0 28 ---- 0.000 0.201 2.091 0.088
125 1.5 Galv Rect ---- 0.200
5.60 40 30 *SR5-5-MN 1

SR-320 22.9 EF 0.100 Rect Rect ---- 0.200 0.200 0.095 0.112
ST-440 16.0 0 -0.200 ---- 0.000 0.003 1.506 0.467
1,538 28.0 22 ---- 0.000 0.203 1.601 0.579
4,398 2.5 Galv Rect ---- 0.200
17.90 40 30 *SR5-5-MN 1

* Loss coefficient for indicated fitting was extrapolated due to table extents being exceeded.

52 of 68
C:\disc top 6.02\ DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 20

System 1 "PACU 1&2" - Runout Output Data - Return


Fit Sect Sect Cumul Press
Runout Dia SM L/100 Shape Ups.Sh ------ ------ ------ ------ ------
Conn Hei TOA Reg Fit1 Qty Coef Loss Diff. Dynam Vel.P Veloc
Vel Wid Gau Fit2 Qty Coef Loss Add.L Fric Stat Stat
CFM Len Ref Mat Fit3 Qty Coef Loss F.Tot Total Total Total
Orif R.NC Act.NC Ups.Junc Qty Coef Loss Dynam
RR-100 38.2 EF 0.080 Rect Rect ---- 0.000 0.000 0.033 0.172
RT-110 26.0 0 -0.020 ---- 0.000 0.002 0.563 0.000
1,641 48.0 20 ---- 0.000 0.002 0.596 0.172
13,061 2.0 Galv Rect ---- 0.000
38.20 40 30 *SR5-5-MN 1

RR-110 35.0 EF 0.010 Rect Rect ---- 0.000 0.099 0.185 0.020
RT-100 26.0 0 0.087 ---- 0.000 0.001 0.366 0.197
564 39.8 20 ---- 0.099 0.099 0.551 0.218
3,770 7.0 Galv Rect ---- 0.099
32.00 40 30 SR5-5-MN 1 5.473 0.099

* Loss coefficient for indicated fitting was extrapolated due to table extents being exceeded.

53 of 68
C:\disc top 6.02\ DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 21

System 1 "PACU 1&2" - Output Summary - Supply


Number of active trunks: 33
Number of active runouts: 23
Total system weight (lb.) minus fittings: 2,823.02
Total outlet flow 19,612
Total outlet flow after heat gain 19,612
Size of largest trunk: 41.5
Size of smallest trunk: 9.7
Size of largest runout: 22.9
Size of smallest runout: 6.6
Maximum static pressure loss occurrs in route to runout: SR-120
Cumulative static pressure loss at above runout: 1.97
Isolate Return From Supply Option: No
Return SP Loss Added to 1st Trunk of Supply: 0.56
Available static pressure at above runout: 0.00
Fan static pressure: 1.97
Fan velocity pressure: 0.21
Fan total pressure: 2.18

54 of 68
C:\disc top 6.02\ DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 22

System 1 "PACU 1&2" - Output Summary - Return


Number of active trunks: 2
Number of active runouts: 2
Total system weight (lb.) minus fittings: 887.60
Total outlet flow 16,831
Total outlet flow after heat gain 16,831
Size of largest trunk: 41.5
Size of smallest trunk: 39.4
Size of largest runout: 38.2
Size of smallest runout: 35.0
Maximum static pressure loss occurrs in route to runout: RR-100
Cumulative static pressure loss at above runout: 0.56
Isolate Return From Supply Option: No
Return SP Loss Added to 1st Trunk of Supply: 0.56
Available static pressure at above runout: 0.00
Fan static pressure: 0.56
Fan velocity pressure: 0.21
Fan total pressure: 0.77

55 of 68
C:\disc top 6.02\ DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 23

System 1 "PACU 1&2" - Runout Sound Data - Supply


Runout
63 125 250 500 1000 2000 4000 8000 NC
Name
SR-100 Required Attenuation 0 7 13 19 23 25 26 27 40
Actual Attenuation 50 46 46 55 91 94 61 64 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-110 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 56 53 58 79 140 145 89 91 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-120 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 52 48 46 52 86 107 65 66 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-130 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 49 45 48 67 124 112 73 75 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-140 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 53 50 57 80 148 142 88 91 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-150 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 52 50 58 86 158 167 99 102 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-160 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 54 53 64 97 181 213 119 122 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-170 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 53 50 54 71 126 174 98 101 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-180 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 49 46 47 61 108 138 82 85 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-190 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 55 53 59 81 144 212 115 118 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-200 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 53 49 53 69 121 165 94 97 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-210 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 54 52 57 78 139 200 110 113 30
Additional Attenuation 0 0 0 0 0 0 0 0

Required Attenuation 0 7 13 19 23 25 26 27 40
Actual Attenuation 54 51 55 73 129 176 101 104 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-230 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 44 43 47 62 105 100 69 72 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-240 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 40 38 39 51 84 75 56 59 30
56 of 68
C:\disc top 6.02\ DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 24

System 1 "PACU 1&2" - Runout Sound Data - Supply (cont'd)


Runout
63 125 250 500 1000 2000 4000 8000 NC
Name
Additional Attenuation 0 0 0 0 0 0 0 0

SR-250 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 39 36 35 43 69 64 48 51 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-260 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 39 36 34 40 64 59 45 48 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-270 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 40 37 36 45 73 67 50 53 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-280 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 42 39 39 51 85 77 56 59 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-290 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 52 50 54 69 119 178 96 99 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-300 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 53 51 55 72 124 189 101 103 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-310 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 53 49 49 57 94 124 73 74 30
Additional Attenuation 0 0 0 0 0 0 0 0

SR-320 Required Attenuation 0 7 13 19 23 25 26 27 40


Actual Attenuation 43 40 43 62 107 98 67 70 30
Additional Attenuation 0 0 0 0 0 0 0 0

57 of 68
C:\disc top 6.0 DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 25

System 1 "PACU 1&2" - Runout Sound Data - Return


Runout
63 125 250 500 1000 2000 4000 8000 NC
Name
RR-100 Required Attenuation -12 -5 1 7 11 13 14 15 40
Actual Attenuation 27 25 24 30 48 46 35 38 30
Additional Attenuation 0 0 0 0 0 0 0 0

RR-110 Required Attenuation -12 -5 1 7 11 13 14 15 40


Actual Attenuation 29 28 28 36 50 48 41 44 30
Additional Attenuation 0 0 0 0 0 0 0 0

58 of 68
C:\disc top 6. DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 26

Duct Connection Tree Diagram - System 1 - PACU 1&2


System 1 - PACU 1&2
Supply
ST-100
ST-490
ST-230
ST-240
SR-250
ST-250
SR-240
ST-260
SR-230
ST-270
SR-260
ST-280
SR-270
ST-290
SR-280
ST-440
SR-320
ST-480
ST-120
SR-100
ST-130
ST-140
ST-430
SR-130
ST-450
SR-110
ST-170
SR-140
ST-180
SR-160
ST-190
SR-150
ST-460
ST-390
SR-180
ST-370
ST-380
SR-190
ST-470
SR-210
ST-400

ST-410
SR-200
ST-420
59 of 68
C:\disc top 6.02\ DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
Ductsize - HVAC Duct Sizing Elite Software Development, Inc.
132/33KV SUBSTATION
Page 27

Duct Connection Tree Diagram - System 1 - PACU 1&2 (cont'd)


SR-170
ST-300
SR-120
ST-310
ST-320
ST-350
SR-290
ST-340
SR-300
ST-330
SR-310
Return
RT-100
RR-110
RT-110
RR-100

60 of 68
C:\disc top 6.02\ DUCTING.dsw Wednesday, February 11, 2009, 11:28 PM
ELECTRIC DUCT HEATER SIZING EDH-1 :

Data:

Total air flow = 19613 cfm From Load calculation


Air Flow rate required at heater = 19613 cfm Total air flow
Total heating required = 171992 Btuh. From Load Calculation

Calculation.
Desired heating capacity in KW Total heating required in BTUH.
3520 BTU/Hr./kW
= 50.39 kW
Equipment heat load= 53.69 kw
Consider 50% from Equipment heat load= 26.845 kw
Net heating required = 50.4 - 26.845 =23.6 KW
Take 10% safty
Net heating required = 23.6 X 1.1=28.32 KW
Use Heater Capacity =29 kW

Size on location of Elec. heater : 1500 x650mm


5' x2.17'
13.5 Sqft.
KW per square feet 29/13.5 =2.2 kw/sqft. = 13.4 watts/sq.inch
Maximum element heating density shall be 55 watts/sq.inch
As per SEC-EOA Std.(73-SMSS-1, Rev.4, page 19 of 32)
HENCE 13.4 WATTA/SQ.INCH IS SAFE

ELECTRICAL DATA OF UNIT MOUNTED HEATER


From the manufacturer's catalogue the
required line current for 1 phase system = Wattage / (Voltage)
= 29000 / 220
= 131.82 Amp

Considered number of step control = 4


Hence the ampere per step = 32.95 amps

61 of 68
BATTERY ROOM EXHAUST FAN SIZING:

DATA

Battery room length 6.00 M


Battery room width 5.900 M
Battery room height 5.40 M
No. of Air changes considered 12 Nos./Hr.

Notes
Number of Air changes required for the battery room is 12 as per the clause
No.4.1.10 of SES-P-119-19 & clause No.10.9 of SES-K-100. Hence 12 air changes
per hour is considered in calculation.

Calculation
3
Volume of Battery room V= 6x5.9x5.4 M
= 191.16 M3
= 6750.75 Ft3
Fan capacity in CFM = Room volume x No. Of Air changes/Hr
60
= 6750.75x12 / 60
= 1350.15 CFM

p y of
Use fan capacity = 1350 CFM
= 2294 CMH
From load calc. Battery Room CFM= 1350 CFM

Pressure loss through the exhaust duct = 0.51 in.W.G. (Ref. To comp. Cal
enclosed)

62 of 68
FIRE FIGHTING EXHAUST FAN SIZING:

DATA

Battery room length 5.09 M 16.70 FT


Battery room width 5.85 M 19.19 FT
Battery room height 6.00 M 19.68 FT
No. of Air changes considered 10 Nos./Hr.

Notes
Number of Air changes required for the battery room is 10 as per the clause
No.4.1.10 of SES-P-119-19 & clause No.10.9 of SES-K-100. Hence 10 air changes
per hour is considered in calculation.

Calculation
3
Volume of Battery room V= 341463415x5.850609756M
= 178.729 M3
= 6311.75 Ft3
Fan capacity in CFM = Room volume x No. Of Air changes/Hr
60
= 6311.75x10 / 60
= 1051.958 CFM

p y of
Use fan capacity = 1125 CFM
= 1912 CMH
From load calc. Battery Room CFM= 1125 CFM

Pressure loss through the exhaust duct = 0.51 in.W.G. (Ref. To comp. Cal
enclosed)

63 of 68
KITCHEN EXHAUST FAN SIZING:

DATA

Battery room length 2.00 M 6.56


Battery room width 1.50 M 4.92
Battery room height 4.00 M 13.1
No. of Air changes considered 10 Nos./Hr.

Notes
Number of Air changes required for the battery room is 12 as per the clause
No.4.1.10 of SES-P-119-19 & clause No.10.9 of SES-K-100. Hence 12 air changes
per hour is considered in calculation.

Calculation
3
Volume of Battery room V= 2x1.5x4.0030487804878 M
= 12.00915 M3
= 424.1 Ft3
Fan capacity in CFM = Room volume x No. Of Air changes/Hr
60
= 424.1x10 / 60
= 71 CFM

p y of
Use fan capacity = 71 CFM
= 121 CMH
From load calc. Battery Room CFM= 194 CFM
ACTUAL AIR CHANGE= 27 ACH
Pressure loss through the exhaust duct = 0.51 in.W.G. (Ref. To comp. Cal
enclosed)

64 of 68
TOILET EXHAUST FAN SIZING :

DATA

Toilet length 3.46 M


Toilet width 2.99 M
Toilet height 4.00 M
Air change 10 AC/Hr.

Notes:
Number of Air changes required for the toilet is 6-10 as per the clause No.4.1.11 of
SES-P-119-19 & clause No.10.11 of SES-K-100. Hence 10 air changes per hour is
considered in calculation.

Calculation
3
Volume of Battery room V= 3.46x2.99x4 M
= 41.3816 M3
3
= 1461.38 Ft
Fan capacity in CFM = Room volume x No. Of Air changes/Hr
60
= 1461.38x10 / 60
= 244 CFM
= 414 CMH
Use fan capacity of = 244 CFM FROM LOAD CALCULATION

Pressure loss through the exhaust duct = 0.2 in.W.G. (Ref. To comp. Cal
enclosed)
`

65 of 68
SAND TRAP LOUVER AND FRESH AIR FILTER SIZING :

DATA
Required Fresh Air 3,925 CFM
1852 L/s

Velocity through louvers 1.52 M/s (Ref: Clause 6(d) of PTS)


299.21 FPM

Required face area to


keep above velocity , AREA = 1846/1.52
1.22 M2 = 13.11 SQ FT
From the GCC catalogue Selected size =
L= 78 in
W= 78 in

Actual face velocity= 3911/13.41


297.64 FPM

From the graph pressure loss across the louver is= 0.40 in.W.G.

Selected model is WST5 - X , Make : GGC

Sizing of fresh air Aluminum panel filter

Select a 2" thick panel filter for fresh air intake.

Make : FAAS PANEL FILTER

The pressure drop across the filter is 0.06 in.W.G. (Clean)


The pressure drop across the filter is 0.5 in.W.G. (Dirty)

66 of 68
AIR DIFFUSION PERFORMANCE INDEX :-

ZONE
S.No. Particulars BATTARY ROOM STORE ROOM FIRE FIGHTING ROOM AC/DC ROOM TELECOM PASSAGE CONTROL ROOM OFFICE TOILET
Metric unit FPS unit Metric unit FPS unit Metric unit FPS unit Metric unit FPS unit Metric unit FPS unit Metric unit FPS unit Metric unit FPS unit Metric unit FPS unit Metric unit FPS unit
1 Room Length M/FT 6.000 19.686 4.000 13.124 31.800 104.336 8.100 26.576 4.500 14.765 4.000 13.124 31.900 104.664 11.150 36.583 4.500 14.765
2 Room width M/FT 5.950 19.522 5.000 16.405 5.500 18.046 4.000 13.124 3.000 9.843 1.960 6.431 16.150 52.988 4.000 13.124 3.000 9.843
3 R
Room Area M2 /FT2
A 35 700
35.700 384 309
384.309 20 000
20.000 215 299 174.900
215.299 174 900 1882 792
1882.792 32 400
32.400 348 785
348.785 13 500
13.500 145 327
145.327 7 840
7.840 84 397
84.397 515 185 5545.946
515.185 5545 946 44 600
44.600 480 117
480.117 13 500
13.500 145 327
145.327
4 Room Char. Length 6.000 19.686 3.000 9.843 5.500 18.046 4.000 13.124 3.200 10.499 3.000 9.843 2.400 7.874 3.300 10.827 3.000 9.843
Supply air stream
5 Supply air to room
38.24 1,350 14.42 509 31.87 1125 41.30 1458 11.22 396 2.07 73 44.73 1579 3.54 125 6.91 244
Cum/Min/CFM
6 Number of Outlets 1 1 1 2 2 1 5 1 1
7 Supply air to outlets
Cum/Min/CFM 38.24 1350.00 14.42 509.00 31.87 1125.00 20.65 729.00 5.61 198.00 2.07 73.00 8.95 315.80 3.54 125.00 6.91 244.00

8 Outlet size MM/In 700x450 28x18 500x250 20x10 750x300 30x12 375x375 15x15 225x225 9x9 150x150 6x6 300x300 12x12 150x150 6x6 300x300 12x12
10 TV/L as per
manufacturer's 3/4 3/4 3/4 - - - - - -
Catalogue
11 Calculated TV - M
6.00 19.69 3.00 9.84 5.50 18.05 4.00 13.12 3.20 10.50 3.00 9.84 2.40 7.87 3.30 10.83 3.00 9.84
/FT
12 Actual TV in FT 24-33 12-18 22-31 14-19 7-10 4-7 8-12 7-11 6-9
13 Sound Level dB 37 <20 37 26 <20 <20 <20 <20 <20
14 Pressure Drop, in W.G
0.013 0.013 0.026 0.066 0.032 0.024 0.032 0.066 0.017
15 Supply register model
SH6-IID SH6-IID SH6-IID CD9-4SD CD9-4SD CD9-4SD CD9-4SD CD9-4SD CD9-4SD
No.
Return Air Stream
16 Return air to outlets
Cum/Min/CFM 38.87 1372 10.57 373 1.76 62 42.10 1486 3.29 116

17 Outlet size MM/In 375X375 15X15 225X225 9X9 150X150 6X6 300X300 12X12 150x150 6X6
18 Number of Return
2 2 1 5 1
registers
19 Sound Level dB 25 <20 <20 <20 <20
20 Pressure Drop, in W.G
-0.269 -0.132 -0.269 -0.097 -0.269
21 Return register model
CD9-4S CD9-4S CD9-4S CD9-4S CD9-4SD
No.
Transfer Air Grilles
27 Air capacity
10.31 364 38.81 1370 10.51 371 3.29 116
Cum/Min/Cfm
28 Exhaust Grille Size 350X300 14X12 700X600 28X16 400X250 16X10 150X150 6X6
29 Exhaust Grille Model
EC14-1D EC14-1D EC14-1D EC14-1D
No.
30 Face velocity 400 FPM 500 FPM 400 FPM 500 FPM
31 Sound Level dB 24 24 24 33
32 Static pressure in.w.g -0.026 -0.042 -0.026 -0.082
Exhaust Air Grilles
27 Air capacity
38.24 1350 31.87 1125 6.91 244
Cum/Min/Cfm
28 Exhaust Grille Size 500X259 20X10 800X300 32X12 300X300 12X12
29 Exhaust Grille Model
EC14-1D EC14-1D EC14-1D
No.
30 Face velocity 500FPM 500 FPM 500 FPM
31 Sound Level dB 28 24 21
32 Static pressure in.w.g -0.059 -0.042 -0.016

67 of 68
AIR DIFFUSION PERFORMANCE INDEX :-
ZONE
S.No. Particulars KITCHEN 33KV SWGR ROOM BASEMENT
Metric unit FPS unit Metric unit FPS unit FPS unit
Metric unit
1 Room Length M/FT 2.000 6.562 18.000 59.058 18.000 59.058
2 Room width M/FT 1.500 4.922 5.500 18.046 5.500 18.046
3 Room Area M2 /FT2 3.000 32.295 99.000 1065.731 99.000 1065.731
4 Room Char. Length 1.500 4.922 4.130 13.551 13.500 44.294
Supply air stream
5 Supply air to room
5.50 194 231.22 8162 124.59 4398
Cum/Min/CFM
6 Number of Outlets 1 6 1
7 Supply air to outlets
5.50 194.00 38.54 1360.33 124.59 4398.00
Cum/Min/CFM
8 Outlet size MM/In 225x225 9x9 300X300 32X16 600x300 24X12
10 TV/L as per
manufacturer's - 3/4 -
Catalogue
11 Calculated TV -
1.50 4.92 4.13 13.55 13.50 44.29
M /FT
12 Actual TV in FT 7-10 24-33 -
13 Sound Level dB <20 37 -
14 Pressure Drop, in
0.032 0.013 0.1
W.G
15 Supply register
CD9-4SD SH6-IID BMO
model No.
Return Air Stream
16 Return air to outlets
444.42 15688 115.38 4073
Cum/Min/CFM
17 Outlet size MM/In 2500X1250 100X50 1000x450 40x18
18 Number of Return
1 1
registers
19 Sound Level dB - -
20 Pressure Drop, in
02
0.2 02
0.2
W.G
21 Return register
BMO BMO
model No.
Transfer Air Grilles
27 Air capacity
Cum/Min/Cfm
28 Exhaust Grille Size
29 Exhaust Grille
Model No.
30 Face velocity
31 Sound Level dB
32 Static pressure
in.w.g
Exhaust Air Grilles
27 Air capacity
5.50 194
Cum/Min/Cfm
28 Exhaust Grille Size 250X250 10X10
29 Exhaust Grille
EC14-1D
Model No.
30 Face velocity 400 FPM
31 Sound Level dB 25
32 Static pressure
-0.026
in.w.g

68 of 68

Das könnte Ihnen auch gefallen